INSTALLATION AND OPERATION MANUAL
FTV/FRV(160,320)(M,S)1(ST,FC)
16- OR 32-CHANNEL10-BIT DIGITALLY ENCODED VIDEO
The FTV/FRV(160,320)(M,S)1(ST,FC) is a multi-channel ten (10) bit digitally
encoded video transmission series. It combines sixteen or thirty-two individual
video signals into one high speed digital stream and transmits this over one
optical fiber. Both the transmitter and receiver are made up from modules:
Multiple 8 Channel Video Modules
One Passive Optical Wavelength Division Multiplexor (WDM)
One Chassis with integral power supply
The outputs of the Video Modules are combined at the transmitter into a single
optical signal by means of the WDM and separated out at the receiver with an
identical WDM. While the WDM has provision for five (5) different wavelengths
(colors), in this application only two wavelengths are used.
The video channels are referred to in numerical order (1 through 16 or 32). A
video input to the channel 3 transmitter BNC connector will be received out of
the channel 3 BNC on the corresponding video receiver module.
The transmitters and receivers come completely assembled and tested from the
factory. There are no optical or electrical adjustments required or permitted.
Bi-color (Red/Green) LED indicators are provided for rapidly ascertaining
equipment operating status. See Figure 5 on Page 7 for LED indication
explanations.
See Figures 1 – 4 for complete installation details.
TECH SUPPORT: (800) 289-9100 INTERNATIONAL: +1 (559) 292-1981
C5631M / REV 04-13-12
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit
from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
14. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases shall be placed on the
apparatus.
15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
16. Installation should be done only by qualified personnel and conform to all local codes.
17. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must
not be installed where exposed to rain and moisture.
18. Use only installation methods and materials capable of supporting four times the maximum specified load.
19. A CCC-approved power cord must be used to power this equipment when used in China.
20. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.
This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
TECH SUPPORT: (800) 289-9100 INTERNATIONAL: +1 (559) 292-1981 C5631M / REV 04-13-12
INSTALLATION AND OPERATION MANUAL FTV/FRV(160,320)(M,S)1(ST,FC)
FIGURE 1 – FTV160(M,S)1(ST,FC) FRONT AND REAR
OPTICALFIBER
CONNECTION
CUSTOMER
Input: 90-264VAC
@1.0Amps 50/60 Hz
Fuse: 1.250ASB, 250 VAC
Output:9.0VDC@6.5Amps
CAUTION!
ForContinuedProtection
AgainstRisk Of Fire,
ReplaceOnlyWithSame
TypeandRatingOfFuse
NC
TX
OPTICAL
13
14
VIDEOIN
15
FIBER
9
10
11
1216
UNITFIBER
5
6
VIDEOIN
7
NC
TX
OPTICAL
1
2
3
48
Power Sources - The product should only
be operated from the
included power supply.
VIDEOTRANSMITTER
CH 1
CH 2
CH 3
CH 4
POWER POWER
CHANNELS
1THRU8
CH 5
CH 6
CH 7
CH 8
FTV160S1ST
16 CHANNEL
VIDEOTRANSMITTER
VIDEOTRANSMITTER
CHANNELS
9 THRU16
CH 9
CH 10
CH 11
CH 12
CH 13
CH 14
CH 15
CH 16
POWER
TECH SUPPORT: (800) 289-9100 INTERNATIONAL: +1 (559) 292-1981
C5631M / REV 04-13-12
Loading...