Pelco FTV10S1STM, FTV10S1FCM, FTV10M1STM Specsheet

PRODUCT SPECIFICATION

FTV10M Miniature Fiber Transmitter

SINGLE-CHANNEL DIGITALLY ENCODED VIDEO

Product Features

• Miniature Module Designed for Use in Pelco®

EH2515/EH3512/EH3515 Series Camera Enclosures and in DF5/DF8 Series Fixed Mount Domes, or for Use as a Stand-Alone Module

• 10-Bit Digitally Encoded Video for High-Quality Transmission over a

Single Fiber

• 1 Simplex Contact Closure

• Multimode Fiber Support for Distances up to 4 km (2.5 mi)

• Single-Mode Fiber Support for Distances up to 54 km (33.6 mi)

• Exceeds All Requirements for EIA RS-250C Short-Haul Transmission

Specifications

• Laser for Transmission of Optical Signals

• Compatible with NTSC, PAL, or SECAM Video Standards

• Designed to Meet NEMA TS 1/TS 2 and Caltrans Traffic Signal

Control Equipment Environmental Standards

• LED Status Indicators for Monitoring All Critical Operating

Parameters

transmission & power

FTV10S1STM

The FTV10M miniature fiber transmitter allows transmission of one composite video channel over one optical fiber. The FTV10M transmitter is compatible with the FRV20 Series receivers. The FTV10M transmitter is available in multimode and single-mode versions. When using single-mode fiber, the FTV10M transmitter and compatible receiver offer an optical power budget of up to 16 dB and provide a transmission distance of up to 54 km (33 mi).

Plug-and-play design ensures ease of installation requiring no electrical or optical adjustments. Specially designed for use in EH2515/EH3512/EH3515 Series camera enclosures and in DF5/DF8 Series fixed mount domes, the FTV10M transmitter can also be used as a stand-alone module. As a stand-alone module, the unit can be placed on a desktop or can be mounted to a wall.

For stand-alone and wall mount installations, external power is required for the FTV10M transmitter. The unit can be powered with the recommended FEXTPS fiber external power supply.

International Standards

Organization Registered Firm;

ISO 9001 Quality System

C3915 / REVISED 11-9-12

TECHNICAL SPECIFICATIONS

MODEL

Optical

Power

Budget

Transmitter

Compatible

Receiver

Fiber Optical

Connector Type

Number

of Fibers

Wavelength

Multimode (62.5/125 µm)

FTV10M1STM FRV20M2ST ST 1 1310 nm 12 dB 4 km (2.5 mi)

Single Mode (9/125 µm)

FTV10S1STM FRV20S2ST ST 1 1310 nm 16 dB 54 km (33.6 mi)

FTV10S1FCM FRV20S2FC FC 1 1310 nm 16 dB 54 km (33.6 mi)

Note: This product requires a fiber installation with a minimum 30 dB connector return loss *Transmission distance will be diminished if additional losses are introduced by the optical connectors, splices and other factors

regarding the quality of the fiber. Operating distance of multimode is limited by the characteristics of the fiber bandwidth.

Maximum

Transmission

Distance*

VIDEO

Number of Channels 1 Video Input 1.0 Vp-p, 75 ohms Overload >1.5 Vp-p Bandwidth (minimum) 5 Hz to 10 MHz Differential Gain <2% Differential Phase <0.7° Tilt <1% Signal-to-Noise Ratio >67 dB typical at maximum optical loss Max. Coaxial Cable (RG59) 100 m (300 ft) camera to fiber optic module to

maintain bandwidth

ELECTRICAL

Power Consumption 2 W, 28 BTU/H Power Input 9 to 36 VDC; 12 to 24 VAC MTBF >100,000 hours Optical Emitter Laser LED Indicators Video, contact Contact Closure Input Closure to ground, 0.33 mA

MECHANICAL

Connectors

Power Terminal block Optical ST or FC Video BNC (gold-plated center pin) Contact Terminal block

Current Protection Automatic resettable solid-state current

limiters

Circuit Board Meets IPC standard

GENERAL

Dimensions 5.72 × 7.62 × 2.74 cm

(2.25" D × 3.00" W × 1.08" H) Operating Temperature –40° to 75°C (–40° to 167°F) Storage Temperature –40° to 85°C (–40° to 185°F) Relative Humidity 0% to 95%, noncondensing Unit Weight 0.15 kg (0.34 lb) Shipping Weight 0.90 kg (2.00 lb)

SUPPLIED ACCESSORIES

Wall mounting bracket (supplied); refer to dimension drawing

RECOMMENDED ACCESSORIES

FKIT-DF5DF8 Fiber mount kit for use with DF5 Series and

FKIT-EH2500 Fiber mount kit for use with EH2500 Series

FKIT-EH3500 Fiber mount kit for use with EH3500 Series

FEXTPS Fiber external power supply with multiple

DF8 Series fixed mount domes

enclosures

plug adaptors (North American, Australian, United Kingdom, and European); 100 to 240 VAC, 50 to 60 Hz input, 9 VDC output

CERTIFICATIONS/RATINGS

• CE, Class A

• FCC, Class A

• UL/cUL Listed

•C-Tick

• Designed to meet NEMA TS 1/TS 2 and Caltrans traffic signal control equipment environmental standards

VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS.

Ø 0.21

(0.08)

Ø 0.79

(0.31)

11.71 (4.61)

2.81

(1.10)

1.58

(0.62)

0.79

(0.31)

Pelco by Schneider Electric

3500 Pelco Way, Clovis, California 93612-5699 United States

USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120 www.pelco.com www.pelco.com/community

7.32 (2.88)

Pelco, the Pelco logo, and other tradema rks associated with Pelco products referred

to in this publication are trademarks of P elco, Inc. or its affiliates. ONVIF and the

ONVIF logo are trademarks of ONVIF Inc. All other pro duct names and

Product specifications and availability are subject to change without notice.

services are the property of their re spective companies.