Pelco FTV10D1A2S1FC, FTV10D1A2M1ST, FRV10D1A2M1ST, FRV10D1A2S1ST, FRV10D1A2S1FC Specsheet
PRODUCT SPECIFICATION
transmission & power
FTV10D1A2/FRV10D1A2 Transmitter and Receiver
SINGLE-CHANNEL BIDIRECTIONAL VIDEO WITH BIDIRECTIONAL DATA, AUDIO, AND CONTACT CLOSURE
Product Features
• 10-Bit Digitally Encoded Bidirectional Video for High-Quality
Transmission over a Single Fiber
• 1 Bidirectional Data Channel Supports RS-232, RS-422, and RS-485
(2-wire/4-wire), Manchester, and Bi-Phase Communication
• 2 Bidirectional 24-Bit (96 kHz) Digitally Encoded Audio Channels with
600-Ohm Balanced Line-Level Audio (up to +6 dBm) and 20 to 18 kHz
Audio Bandwidth
• 1 Bidirectional Contact Closure
• Multimode Fiber Support for Distances up to 4 km (2.5 mi)
• Single-Mode Support for Distances up to 48 km (29.8 mi)
• Exceeds All Requirements for the EIA RS-250C Short-Haul
Transmission Specification
• Laser Diode for Transmission of Optical Signals
• Compatible NTSC, PAL, and SECAM Video Standards
• Designed to Meet NEMA TS 1/TS 2 and Caltrans Traffic Signal
Control Equipment Environmental Standards
• Voltage Transient Protection on All Power and Signal
Input/Output Lines
• LED Status Indicators for Monitoring All Critical
Operating Parameters
• Hot-Swappable Rack Modules
• Stand-Alone or Rack-Mountable Modular Design
FTV10D1A2S1FC
The FTV10D1A2/FRV10D1A2 fiber transmitter and receiver provide
simultaneous transmission of one bidirectional video channel, one
bidirectional data channel, two bidirectional audio channels, and one
bidirectional contact closure over one optical fiber in a two-slot wide
design. Units are available in single-mode and multimode versions.
The FTV10D1A2 transmitter and FRV10D1A2 receiver provide
transmission of two bidirectional 24-bit (96 kHz) audio signals with
sample rate digital encoding for superior transmission of balanced
line-level audio. Data selection offers a choice of RS-232, RS-422,
and RS-485 (2-wire/4-wire), Manchester, and Bi-Phase
Communication.
The FTV10D1A2/FRV10D1A2 plug-and-play design ensures ease of
installation by requiring no electrical or optical adjustments.
Modular in design, FTV10D1A2 and FRV10D1A2 units can be
rack-mounted using the EURACK/USRACK chassis, or stand-alone
modules can be placed on a desktop or mounted to a wall (wall
mount kit not required).
For stand-alone and wall mount installations, external power is
required for the FTV10D1A2/FRV10D1A2 units. The units can be
powered with the recommended FEXTPS fiber external power supply.
International Standards
Organization Registered Firm;
ISO 9001 Quality System
C3925 / NEW 6-7-12
TECHNICAL SPECIFICATIONS
MODEL
Transmitter
Compatible
Receiver
Fiber Optical
Connector Type
Number
of Fibers
Wavelength
Optical Power
Budget
Multimode (62.5/125 µm)
FTV10D1A2M1ST FRV10D1A2M1ST ST 1 1310/1550 nm 16 dB 4 km (2.5 mi)
Single Mode (9/125 µm)
FTV10D1A2S1ST FRV10D1A2S1ST ST 1 1310/1550 nm 16 dB 48 km (29.8 mi)
FTV10D1A2S1FC FRV10D1A2S1FC FC 1 1310/1550 nm 16 dB 48 km (29.8 mi)
Note: This product requires a fiber installation with a minimum 30 dB connector return loss.
*Distance may be limited by optical dispersion.
Maximum
Transmission
Distance*
VIDEO/ELECTRICAL
Number of Channels 1
Video Input (FTV10D1A2)/
Video Output (FRV10D1A2) 1.0 Vp-p, 75 ohms; NTSC, PAL, SECAM
Overload >1.5 Vp-p
Bandwidth 10 Hz to 6.5 MHz per channel
Differential Gain <2%
Differential Phase <0.7°
Tilt <1%
Signal-to-Noise Ratio 67 dB typical
Max. Coaxial Cable (RG59) 100 m (300 ft) camera to fiber optic module
maintains 6 Mhz bandwidth
Power
Surface Mount 8 to 15 VDC at 4 W
Rack Mount Provided by rack
MTBF >100,000 hours
LED Indicators Link, Video, Data, Audio, Contact Closure,
Power
DATA
Number of Channels 1
Data Communication RS-232, RS-422, and RS-485 (2-wire/4-wire),
Manchester, and Bi-Phase
Maximum Baud Rate 250 Kbps
Operating Mode Simplex or full-duplex
Bit Error Rate <10
-9
at maximum optical loss budget
AUDIO
Audio Channels 2 (balanced)
Audio Input/Output Signal Maximum 4.4 Vp-p (+6 dBm)
Bandwidth 20 Hz to 18 kHz
Total Harmonic Distortion 0.02%
Signal-to-Noise Ratio (SNR) 85 dB (typical)
CONTACT CLOSURE
Number of Channels 1
Contact Interface 0.5 ms response time
Input Dry
Output SPST relay, 0.15 A contact rating, normally
open
MECHANICAL
Connectors
Optical ST or FC
Power Terminal block
Video BNC
Data Terminal block
Audio Terminal block
Alarm Terminal block
Contact Terminal block
Number of Rack Slots 2
GENERAL
Dimensions 15.5 × 13.5 × 5.6 cm
Operating Temperature –40° to 75°C (–40° to 167°F)
Storage Temperature –40° to 85°C (–40° to 185°F)
Relative Humidity 0 to 95%, noncondensing
Unit Weight 0.5 kg (1.5 lb)
Shipping Weight 0.9 kg (2.0 lb)
CERTIFICATIONS/RATINGS
• CE, Class A
• FCC, Class A
• UL/cUL Listed
•C-Tick
• Designed to meet NEMA TS 1/TS 2 and Caltrans traffic signal control
equipment environmental standards
†
At the time of this printing, all certifications are pending. Please
consult the factory, our Web site (www.pelco.com), or the most
recent B.O.S.S.
®
update for the current status of certifications.
(6.1" D × 5.3" W × 2.2" H)
†
RECOMMENDED ACCESSORIES
EURACK 4 RU rack accessory with European power
USRACK 4 RU rack accessory with North American
FEXTPS Fiber External Power Supply with multiple
supply
power supply
plug adaptors (North American, Australian,
United Kingdom, and European);
100 to 240 VAC, 50 to 60 Hz input,
9 VDC output
Pelco by Schneider Electric
3500 Pelco Way, Clovis, California 93612-5699 United States
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120
www.pelco.com
Pelco, the Pelco logo, and other tra demarks associated with Pelco products referred
to in this publication are trademarks of Pelco, Inc. or its affiliates. All other
product names and services are the prope rty of their respective companies.
Product specifications and availability are subject to change without notice.
©Copyright 2012, Pelco, Inc. All rights reserved.
Loading...