Pelco FTV10D11, FTV10D1M1ST, FTV10D1S1FC, FRV10D1M1, FRV10D1S1ST operations manual

INSTALLATION AND OPERATION MANUAL

FTV/FRV10D1(M,S)1(ST,FC) Series

10-BIT DIGITALLY ENCODED VIDEO WITH “UP-THE-COAX”
EXTENDED DISTANCE OR BI-DIRECTIONAL DATA
(RS232, RS422 RS485 2/4W)

The FTV/FRV10D1(M,S)1(ST,FC) series transmits 10 bit digital video and

full duplex data over one Singlemode or Multimode fiber. The video supports

NTSC, PAL and SECAM CCTV camera systems. The data supports RS232,

RS422 and RS485 (2W & 4W) at data rates up to 115 Kbps (NRZ). The FTV/

FRV10D1(M,S)1(ST,FC) series also supports “Up-the-Coax” control signals

for Pelco Coaxitron. The product is “Plug-and-Play” with no electrical or optical

adjustments.

The FTV/FRV10D1(M,S)1(ST,FC) series allows the user to choose

bi-directional data or up-the-coax data through a switch on the unit, as

described in Figure 5 on Page 4.

Bi-color (Red/Green) LED indicators are provided for rapidly ascertaining

equipment operating status. Figure 6 on Page 4 describes the LED indicators

for each light on the unit.

These units are interchangeable between stand-alone or card mount

configurations. See Figure A on Page 6 for installation instructions.

See Figures 1 – 7 for complete installation details.

TECH SUPPORT: [phone] INTERNATIONAL: [phone]

C5633M-A / REV 07-24-14

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit
from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.

14. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases shall be placed on the
apparatus.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

16. Installation should be done only by qualified personnel and conform to all local codes.

17. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must
not be installed where exposed to rain and moisture.

18. Use only installation methods and materials capable of supporting four times the maximum specified load.

19. A CCC-approved power cord must be used to power this equipment when used in China.

20. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit.

This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

TECH SUPPORT: [phone] INTERNATIONAL: [phone] C5633M-A / REV 07-24-14

GND

+Vin

PWR

OPTICAL

IN/OUT

VIDEOIN

B

A

DOUT-

DOUT+

DIN-

DIN+

GND

DIN

DOUT

232485422

DATA

GND

+Vin

PWR

OPTICAL

IN/OUT

VIDEOIN

B

A

DOUT-

DOUT+

DIN-

DIN+

GND

DIN

DOUT

232485422

DATA

GND

+Vin

PWR

OPTICAL

IN/OUT

VIDEOOUT

B

A

DOUT-

DOUT+

DIN-

DIN+

GND

DIN

DOUT

232485422

DATA

INSTALLATION AND OPERATION MANUAL FTV/FRV10D1(M,S)1(ST,FC)

FIGURE 1 – FTV/FRV10D1(M,S)1(ST,FC) SERIES TRANSMITTER AND RECEIVER

MULTIMODE OR SINGLE MODE
OPTICAL FIBER

BLACK WITH WHITE STRIPES

BLACK
Power Supply:
Surface Mount: 8–15 VDC @ 2W
Rack Mount: From Rack
NOTE: Remove Electrical Connector for Rack
Mount Units
Above wiring assumes use of Pelco FEXTPS
power supply. When using non-Pelco power
supplies, confirm polarity before connecting.

FIGURE 2 – TRANSMITTER

REAR PANEL REAR PANELFRONT PANEL FRONT PANEL

FTV10D1S1ST

VIDEO

TRANSMITTER

+
2 WAY DATA /
UP the COAX

VIDEOIN

LINK

VIDEO

DATA IN

DATAOUT

POWER

12

ON

DOUT

DIN
GND
DIN+

DIN­DOUT+
DOUT-

GND

+Vin

TECH SUPPORT: [phone] INTERNATIONAL: [phone]

IN/OUT

OPTICAL

DATA

232485422

A
B

PWR

FIGURE 3 – RECEIVER

FRV10D1S1ST

VIDEO

RECEIVER

+
2 WAY DATA /
UP the COAX

LINK

VIDEO

DATA IN

DATAOUT

ON

12

POWER

VIDEOOUT

DOUT

DIN
GND
DIN+

DIN­DOUT+
DOUT-

GND

+Vin

IN/OUT

OPTICAL

DATA

232485422

A
B

PWR

C5633M-A / REV 07-24-14

INSTALLATION AND OPERATION MANUAL FTV/FRV10D1(M,S)1(ST,FC)

12

ON

DATAOUT

DATA IN

VIDEO

LINK

FTV10D1S1ST

VIDEO

TRANSMITTER

+
2 WAY DATA /
UP the COAX

FIGURE 4 – DATA CHANNEL CONNECTIONS

FIGURE 5 – SWITCH POSITIONS

The mode for each data channel is configured using a pair of switches on the front panel of the unit.

Switch

FIGURE 6 – LED INDICATORS

GREEN Communication link

RED Communication

OFF Unit powered down.

1 2

Up-the-Coax

Protocols

LINK VIDEO DATA IN DATA OUT POWER

has been established

over optical fiber

link has not been
established.

An active video signal

is present on the BNC

connector.

– – – –

An active data signal

is present on the

input pins of the data

connector.

1 2

RS485

4-Wire Data

An active data signal

is present on the

output pins of the

data connector.

1 2 1 2

RS232 Data RS422,

Unit powered up

RS485 2-Wire,

Manchester or

Bi-Phase Data

TECH SUPPORT: [phone] INTERNATIONAL: [phone] C5633M-A / REV 07-24-14

INSTALLATION AND OPERATION MANUAL FTV/FRV10D1(M,S)1(ST,FC)

FIGURE 7 – DATA CONNECTIONS

UTC Control

RS232

RS422

Customer

Equipment

Up-the-Coax

Control Receiver

Customer

Equipment

Data Transmit

Data Receive

Signal Ground

Data Out (+)

Data Out (–)

Data In (+)

Data In (–)

Transmitter

VIDEO IN

Transmitter

DIN

DOUT

GND

DIN(+)

DIN(–)

DOUT(+)

DOUT(–)

Receiver

VIDEO OUT

Receiver

DOUT

DIN

GND

DOUT(+)

DOUT(–)

DIN(+)

DIN(–)

Customer

Equipment

Up-the-Coax

Control Transmitter

Customer

Equipment

Data Receive

Data Transmit

Signal Ground

Data In (+)

Data In (–)

Data Out (+)

Data Out (–)

Bi-phase or

Manchester

2-Wire

RS485

4-Wire

RS485

Data Out (+)

Data Out (–)

Data (A)

Data (B)

Data Out (A)

Data Out (B)

Data In (A)

Data In (B)

DIN(+)

DIN(–)

A

B

A

B

DOUT(+)

DOUT(–)

DOUT(+)

DOUT(–)

A

B

DOUT(+)

DOUT(–)

A

B

Data In (+)

Data In (–)

Data (A)

Data (B)

Data In (A)

Data In (B)

Data Out (A)

Data Out (B)

TECH SUPPORT: [phone] INTERNATIONAL: [phone]

C5633M-A / REV 07-24-14

MECHANICAL INSTALLATION INSTRUCTIONS

INSTALLATION CONSIDERATIONS

This fiber-optic link is supplied as a Standalone/Rack module. Units
should be installed in dry locations protected from extremes of
temperature and humidity.

CARD CAGE RACKS

CAUTION: Although the units are hot-swappable and may be installed

without turning power off to the rack, the manufacturer recommends
that the power supply be turned off and that the rack power supply
is disconnected from any power source. Note: Remove electrical
connector before installing in card cage rack.

1. Make sure that the card is oriented right side up, and slide it into the
card guides in the rack until the edge connector at the back of the
card seats in the corresponding slot in the rack’s connector panel.
Seating may require thumb pressure on the top and bottom of the
card’s front panel.

CAUTION: Take care not to press on any of the LEDs.

2. Tighten the two thumb screws on the card until the front panel of the
card is seated against the front of the rack.

WARNING: Unit is to be used with a Listed Class 2 power supply.

FIGURE A

Dimensions are for a standard one slot module

.2cm

[5.2in]

11.9cm
[4.7in]

7. 5cm

0.63cm
[0.25in]

[2.9in]

15cm

[5.9in]

IMPORTANT SAFEGUARDS:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack

assembly, the operating ambient temperature of the rack environment may
be greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such

that the amount of air flow required for safe operation of the equipment is not
compromised.

2.75cm
[1.1in]

TECH SUPPORT: [phone] INTERNATIONAL: [phone] C5633M-A / REV 07-24-14

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

•Five years:
–Fiber optic products
– Unshielded Twisted Pair (UTP) transmission products
–CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

MC3651H-2X camera models

• Three years:
–FD Series and BU Series analog camera models
–Fixed network cameras and network dome cameras with Sarix
–Sarix thermal imaging products (TI and ESTI Series)
–Fixed analog camera models (C20 Series, CCC1390H Series, C10DN Series,

and C10CH Series)
– EH1500 Series enclosures
–Spectra
–Spectra HD dome products
–Camclosure

®

IV products (including Spectra IV IP)

®

IS Series integrated camera systems

– DX Series video recorders (except DX9000 Series which is covered for a

period of one year), DVR5100 Series digital video recorders, Digital Sentry

Series hardware products, DVX Series digital video recorders, and NVR300

Series network video recorders

®

– Endura
– Genex

Series distributed network-based video products

®

Series products (multiplexers, server, and keyboard)
– PMCL200/300/400 Series LCD monitors
–PMCL5xxF Series and PMCL5xxNB Series LCD monitors

•Two years:
–Standard varifocal, fixed focal, and motorized zoom lenses
– DF5/DF8 Series fixed dome products

®

–Legacy
–Spectra III

Series integrated positioning systems

™

, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, ExSite IP, and

PS20 scanners, including when used in continuous motion applications
– Esprit Ti and TI2500 Series thermal imaging products
– Esprit and WW5700 Series window wiper (excluding wiper blades)
–CM6700/CM6800/CM9700 Series matrix
– Digital Light Processing (DLP

®

) displays (except lamp and color wheel). The
lamp and color wheel will be covered for a period of 90 days. The air filter is
not covered under warranty.

®

technology

•Six months:
– All pan and tilts, scanners, or preset lenses used in continuous motion

applications (preset scan, tour, and auto scan modes)

Pelco will warrant all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid
to a Pelco designated location. Repairs made necessary by reason of misuse,

alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss
resulting from the specific use or application made of the Products. Pelco’s liability
for any claim, whether based on breach of contract, negligence, infringement of
any rights of any party or product liability, relating to the Products shall not exceed
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be
liable for any special, incidental, or consequential damages (including loss of use,
loss of profit, and claims of third parties) however caused, whether by the
negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at [phone] or
[phone] to obtain a Repair Authorization

®

following information:

number (RA), and provide the

1. Model and serial number

2. Date of shipment, P. O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product that does not fall under
the warranty conditions stated above, please include a written explanation with
the product when returned.

Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.

RETURNS

To expedite parts returned for repair or credit, please call Pelco at [phone]
or [phone] to obtain an authorization number (CA number if returned for
credit, and RA number if returned for repair) and designated return location.

All merchandise returned for credit may be subject to a 20 percent restocking and
refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned
CA or RA number and freight should be prepaid.

Revised 1-12-12

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pe .cnI ,ocleP ,2102 thgirypoC © .setailiffa sti ro .cnI ,ocl
All other product names and services are the property of their respective companies. All rights reserved.
Product specifications and availability are subject to change without notice.

www.pelco.com

co, Inc.

Pel

625 W. Alluvial, Fresno, California 93711 United States USA & Canada Tel [phone] Fax (800)

289-9150 I

nternational Tel [phone] Fax [phone] www.pelco.com