Pelco ESTI650-5N, ESTI335-2W, ESTI335-2N, ESTI314-5W, ESTI3100-5W User Manual

INSTALLATION/OPERATION

Sarix® TI Series Fixed Thermal Camera

C1316M-C (8/13)

Contents

Important Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Legal Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Video Quality Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Open Source Software Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Built-in Analytics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Compatible Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

User-Supplied Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Device Configuration Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Accessing the IP Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Live Video Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Settings Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

System Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Network Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Imaging Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Connecting a Relay Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Connecting Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Logging On to the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Live Video Page Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Selecting a Stream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Taking a Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Accessing the Camera Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Changing the Device Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Configuring DHCP Time Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Configuring Manual Time Server Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Customizing the Appearance of the Text Overlay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Generating a System Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Rebooting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Restoring All Camera Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Downloading a Full Backup of Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Uploading a Backup File to Restore Camera Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Changing the Hostname . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Changing the HTTPS Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Turning On DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Configuring a Static IPv4 Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Configuring IPv6 Address Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Selecting the Secure Sockets Layer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Enabling Secure Shell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Configuring the 802.1x Port Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Selecting SNMP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Configuring SNMP V2c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Configuring SNMP V3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Selecting the Color Palette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Changing the Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Changing the Image Enhancement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

. . . . . . . . . . . . . . . . . . . . . . . . . . . .25

C1316M-C (8/13) 3

Configuring Noise Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Configuring the Recalibration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

A/V Streams Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Selecting a Video Preset Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Configuring a Custom Video Stream Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Selecting the Audio Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Users Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Selecting the Users and Groups Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Enabling Remote Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Creating a New User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Editing a User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Deleting a User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Events Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Handlers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Analytic Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Calibrate Scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Behaviors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Adaptive Motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Camera Sabotage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Loitering Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Object Counting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Stopped Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

4 C1316M-C (8/13)

List of Illustrations

1 Camera Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2 Removing the Back Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3 Alarm, Relay, and Audio Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4 Relay Wiring Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

5 Supervised Alarm Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

6 Supervised Alarm Input Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7 Unsupervised Alarm Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

8 Normally Closed and Normally Open Unsupervised Alarm Input Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

9 Alarm Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

10 Line-In Audio Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

11 Line-Out Audio Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

C1316M-C (8/13) 5

Important Notices

LEGAL NOTICE

SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND RECORDING CAPABILITIES, THE IMPROPER USE OF
WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH CAPABILITIES VARY
BETWEEN JURISDICTIONS AND MAY REQUIRE, AMONG OTHER THINGS, EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS. YOU
ARE SOLELY RESPONSIBLE FOR INSURING STRICT COMPLIANCE WITH SUCH LAWS AND FOR STRICT ADHERENCE TO ANY/ALL RIGHTS OF
PRIVACY AND PERSONALTY. USE OF THIS EQUIPMENT AND/OR SOFTWARE FOR ILLEGAL SURVEILLANCE OR MONITORING SHALL BE DEEMED
UNAUTHORIZED USE IN VIOLATION OF THE END USER SOFTWARE AGREEMENT AND RESULT IN THE IMMEDIATE TERMINATION OF YOUR
LICENSE RIGHTS THEREUNDER.

REGULATORY NOTICES

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.

Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission’s rules.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

VIDEO QUALITY CAUTION

FRAME RATE NOTICE REGARDING USER-SELECTED OPTIONS

Pelco systems are capable of providing high quality video for both live viewing and playback. However, the systems can be used in lower quality
modes, which can degrade picture quality, to allow for a slower rate of data transfer and to reduce the amount of video data stored. The picture
quality can be degraded by either lowering the resolution, reducing the picture rate, or both. A picture degraded by having a reduced resolution
may result in an image that is less clear or even indiscernible. A picture degraded by reducing the picture rate has fewer frames per second,
which can result in images that appear to jump or move more quickly than normal during playback. Lower frame rates may result in a key event
not being recorded by the system.

Judgment as to the suitability of the products for users’ purposes is solely the users’ responsibility. Users shall determine the suitability of the
products for their own intended application, picture rate and picture quality. In the event users intend to use the video for evidentiary purposes in
a judicial proceeding or otherwise, users should consult with their attorney regarding any particular requirements for such use.

OPEN SOURCE SOFTWARE NOTICE

This product includes certain open source or other software originated from third parties that is subject to the GNU General Public License (GPL),
GNU Library/Lesser General Public License (LGPL) and different and/or additional copyright licenses, disclaimers, and notices.

The exact terms of GPL, LGPL, and some other licenses are provided to you with this product. Please refer to the exact terms of the GPL and LGPL
at http://www.fsf.org (Free Software Foundation) or http://www.opensource.org (Open Source Initiative) regarding your rights under said license.
You may obtain a complete corresponding machine-readable copy of the source code of such software under the GPL or LGPL by sending your
request to [e-mail]; the subject line should read Source Code Request. You will then receive an email with a link for you to
download the source code.

This offer is valid for a period of three (3) years from the date of the distribution of this product by Pelco.

6 C1316M-C (8/13)

Introduction

The Sarix® TI Series fixed thermal IP camera is an advanced thermal imaging system designed for easy integration into any new or existing video
security application. At the core of the Sarix TI Series is an uncooled, sun-safe, amorphous silicon microbolometer, long wave infrared (LWIR)
camera. Every Sarix TI Series features IP and analog outputs in the same package.

The Sarix TI Series provides outstanding sensitivity below 50 mK. It is capable of multiple display formats, including white hot, black hot, and
rainbow. The Sarix TI Series is available with multiple lens configurations for effective deployment in a wide range of applications.

The camera features open architecture connectivity to third-party software. Pelco offers an application programming interface (API) and software
development kit (SDK) that enables third-party systems to interface with Pelco's IP cameras. The camera is also compatible with Endura
and Digital Sentry

®

to record, manage, configure, and view multiple live streams.

BUILT-IN ANALYTICS

When used in an IP video system, the Sarix TI Series is preloaded with user-configurable behaviors. The device is capable of running up to three
behaviors at the same time; however, the number of behaviors is limited to the available processing power of the camera and the type of analytic
being used.

Pelco analytics are configured and enabled using a standard Web browser. Refer to Analytic Configuration on page 37 for instructions on how to
configure and enable Pelco analytics.

COMPATIBLE SYSTEMS

The device can also be used with an Endura, DX Series, or Digital Sentry system. It also works with many third-party systems with Pelco’s API
and the ONVIF API. For detailed instructions on configuring the device using one of these systems, refer to the manual shipped with the system.

Go to partnerfirst.pelco.com for a list of compatible products and partners.

®

, DX

C1316M-C (8/13) 7

MODELS

640 x 480 Resolution

Lens Format Model

100 mm

50 mm

35 mm

14.25 mm

384 x 288 Resolution

NTSC TI6100

PAL TI6100-X

PAL, 8.33 ips TI6100-X1

NTSC TI650

PAL TI650-X

PAL, 8.33 ips TI650-X1

NTSC TI635

PAL TI635-X

PAL, 8.33 ips TI635-X1

NTSC TI614

PAL TI614-X

PAL, 8.33 ips TI614-X1

Lens Format Model

NTSC TI3100

100 mm

50 mm

35 mm

14.25 mm

PAL TI3100-X

PAL, 8.33 ips TI3100-X1

NTSC TI350

PAL TI350-X

PAL, 8.33 ips TI350-X1

NTSC TI335

PAL TI335-X

PAL, 8.33 ips TI335-X1

NTSC TI314

PAL TI314-X

PAL, 8.33 ips TI314-X1

240 x 184 Resolution

Lens Format Model

6.30 mm

NTSC TI206

PAL TI206-X

8 C1316M-C (8/13)

GETTING STARTED

Before installing your camera, thoroughly familiarize yourself with the information in this section.

NOTES:

• While this camera can operate in both IP and analog modes, it is recommended that you use the camera in only one of these modes at any
given time, not both.

• Pelco recommends connecting the camera to a network that uses a Dynamic Host Configuration Protocol (DHCP) server to address devices.

• Do not use a network hub when configuring the network settings for the camera.

• To ensure secure access to the IP camera, place the camera behind a firewall when it is connected to a network.

PARTS LIST

The following parts are supplied:

Qty Description

1Camera
1 Quick Start Guide
1 Resource disc
3 MAC address labels (extra)
1 T20 security driver bit

USER-SUPPLIED PARTS LIST

Installation tools and mounting hardware are needed but not supplied.

C1316M-C (8/13) 9

Product Overview

ì

Audio Connectors: Enables optional audio capability.

î

BNC Connector: Enables analog video output.

ï

Alarm and Relay Connectors: Enables optional alarms and relays.

ñ

24 VAC Connector: Provides power to the unit.

ó

Micro SD Card Slot: Saves a snapshot image to a micro SD card based on alarm activity.
NOTE: The micro SD card must be formatted as FAT32. Other formats are not compatible with the camera.

r

Reset Button: Reboots the camera or restores the camera’s factory default settings. This button is recessed. Using a small tool, such as
a paper clip, press and release the reset button once to reboot the camera. Press and hold the reset button for 10 seconds to restore the
camera to the factory default settings.

s

Ethernet Link LED: Flashes green to indicate that a live network connection is established.

Figure 1. Camera Features

t

Ethernet Activity LED: Glows solid green to indicate that data is being transmitted or received by the camera.

u

Product Label: Lists the model number, revision number, serial number, and Media Access Control (MAC) address. This information
might be required for setup.

NOTE: Figure 1 shows the camera with the back cover removed.

10 C1316M-C (8/13)

Installation

1. Mount the camera in the desired location using a recommended mount (refer to the instructions provided with the mount).

NOTE: Do not install the camera behind a window or other glass. Glass is opaque to long wave infrared and will block the camera's view.

2. Loosen the two T20 security screws using a T20 security driver bit (supplied), and then remove the back cover.

3. Connect all wires and cables (refer to Figure 1 on page 10).

4. Optional: Connect the wiring for relays, alarms, and audio. Refer to Wiring on page 12 for more information.

5. Turn on the system power.

NOTE: There might be a delay of approximately 3 minutes between power up and video being displayed in analog installations.

6. Refer to Operation on page 16 for instructions on how to use your Sarix TI system.

Figure 2. Removing the Back Cover

C1316M-C (8/13) 11

WIRING

IN

A1

NO

_

+

_

+

OUT

Figure 3. Alarm, Relay, and Audio Connections

Table A. Pinouts for Alarm, Relay, and Audio Connections.

Pin Group Pin Description

A1 Alarm Input

Alarm Return

NO Normally Open (N.O.) Relay Output.

Relay Return

– Audio Line-In (negative)

+ Audio Line-In (positive)

– Audio Line-Out (negative)

+ Audio Line-Out (positive)

CONNECTING A RELAY DEVICE

NOTE: Relays must be configured using the Web interface.

The Sarix TI has one output for activating external devices. It supports both momentary and continuous relay operation.

You can operate the relays interactively during an active connection, or they can operate automatically to coincide with certain events. Typical
applications include turning on lights or other electrical devices or activating a door, gate, or lock.

WARNING: Do not exceed the maximum relay ratings of 15 VDC, 75 mA.

CCESSORYSARIX TI

USER A

A1

A2

Figure 4. Relay Wiring Diagram

12 C1316M-C (8/13)

CONNECTING ALARMS

1 KΩ

A

1

1 KΩ

A

1

NORMALLY OPENNORMALLY CLOSED

NOTE: Alarms must be configured using the Web interface.

The Sarix TI provides one alarm input for external signaling devices, such as door contacts or motion detectors. Both normally open and normally
closed devices are supported.

Supervised Alarms

When an alarm is configured as a supervised alarm, the Sarix TI maintains a constant electrical current through the alarm circuit
(3.3 VDC, 1 kohm). If the alarm circuit length changes, due to an electrical short or a bypass, the voltage fluctuates from its normal state and
activates an alarm.

NOTE: Install the 1-kohm resistor as close to the switch as possible.

Figure 5 illustrates the alarm and no alarm conditions of a supervised alarm input. Whether the alarm is normally closed or normally open,
neither a cut nor a bypass can defeat these alarms.

NORMALLY OPENNORMALLY CLOSED

NO ALARM

GND

1 KΩ

+V

NO ALARM

GND

1 KΩ

+V

ALARM

ALARM

ALARM

GND

GND

GND

1 KΩ

+V

1 KΩ

+V

CUT

1 KΩ

+V

BYPASS

Figure 5. Supervised Alarm Conditions

Figure 6 illustrates the wiring configuration for supervised alarm inputs.

Figure 6. Supervised Alarm Input Wiring

ALARM

GND

ALARM

GND

ALARM

GND

1 KΩ

+V

1 KΩ

+V

CUT

1 KΩ

+V

BYPASS

C1316M-C (8/13) 13

Unsupervised Alarms

+V

+V

+V

+V

+V

+V

+V

+V

BYPASS

CUT

BYPASS

CUT

GND

ALARM

GND

ALARM

GND

NO ALARM

GND

NO ALARM

GND

NO ALARM

GND

ALARM

GND

NO ALARM

GND

ALARM

NORMALLY OPENNORMALLY CLOSED

A1A1

NORMALLY OPENNORMALLY CLOSED

When an alarm is configured as an unsupervised alarm, an alarm is only activated when the normal alarm state (open or closed) changes.

Figure 7 illustrates the alarm and no alarm conditions of an unsupervised alarm input.

Figure 7. Unsupervised Alarm Conditions

Figure 8 illustrates the wiring configuration for unsupervised alarm inputs.

Figure 8. Normally Closed and Normally Open Unsupervised Alarm Input Wiring

NOTE: A normally closed alarm input can be defeated with a bypass; a normally open input can be defeated with a cut.

Alarm Connections

Figure 9 shows how to wire the Sarix TI to an alarm.

ALARM A1

ALARM

Figure 9. Alarm Connections

14 C1316M-C (8/13)

CONNECTING AUDIO

+

–

NOTES:

• The maximum recommended cable length for the audio wiring is 304.8 m (1,000 ft).

• The Sarix TI is designed to work with microphones that have an internal preamplifier and provide professional line-level output (+4 dBu).

• If your microphone is a consumer line-level device (–10 dBu), the audio output may be quieter than you expect. Mic-level devices are not
recommended as they must be amplified to a line-level signal, which often results in excessive noise.

Figure 10. Line-In Audio Wiring

ì

Microphone

î

Amplifier

ï

600-Ohm Impedance Matching Transformer

ñ

Line In –

ó

Line In +

+

–

Figure 11. Line-Out Audio Wiring

ì

Speaker

î

Amplifier

ï

600-Ohm Impedance Matching Transformer

ñ

Line Out –

ó

Line Out +

C1316M-C (8/13) 15

Operation

DEVICE CONFIGURATION SEQUENCE

Once the device is installed and power is applied, the device undergoes a configuration sequence. The configuration sequence takes
approximately two minutes to complete, and then the device will come on line.

NOTE: If the device is not connected to a Dynamic Host Configuration Protocol (DHCP) server and DHCP is enabled, the configuration sequence
might take up to five minutes to complete.

MINIMUM SYSTEM REQUIREMENTS

Network interface card: 100 megabits (or greater)

Monitor: Minimum of 1024 x 768 resolution, 16- or 32-bit pixel color resolution

®

Web browser: Internet Explorer
analytics

Media player: Pelco Media Player or QuickTime
(or later)

NOTES:

• Pelco Media Player is recommended for control, smoothness, and reduced latency as compared to QuickTime.

• This product is not compatible with QuickTime version 7.6.4 for Windows XP or Windows Vista. If you have this version installed on your PC,
you will need to upgrade to QuickTime version 7.6.5.

• Network and processor bandwidth limitations might cause the video stream to pause or appear pixelated when additional Web-interface
users connect to the camera. Decrease the images per second (ips), resolution, compression, or bit rate settings of the Web interface video
streams to compensate for network or processor limitations.

8.0 (or later) or Mozilla® Firefox® 3.5 (or later); Internet Explorer 8.0 (or later) is recommended for configuring

®

7.6.5 for Windows XP, Windows Vista, and Windows 7; or QuickTime 7.6.4 for Mac OS X 10.4

ACCESSING THE IP CAMERA

The first time you access the camera, the live video page appears. By default, you are viewing the video as a public user and only have access to
the single stream live view.

If, for security purposes, users should not be allowed to view video without first logging on to the camera, change the permissions for public
users.

LOGGING ON TO THE CAMERA

1. Open the Web browser.

2. Type the camera’s IP address in the browser address bar.

NOTE: If you do not know the camera’s IP address, you can locate it using the Pelco Device Utility software.

3. Click the Login button in the navigation bar; a dialog box opens.

4. Type your user name and password.

NOTE: If you are logging on to the camera as the administrator for the first time, the default user name and password are admin
(all lowercase). For security purposes, be sure to change the password after you log on for the first time.

5. Click Log In.

16 C1316M-C (8/13)

LIVE VIDEO PAGE

The live video page allows you to manage the way you view live video and capture images. You can also view live video from this page and
access menus on the navigation bar (based on user permissions).

LIVE VIDEO PAGE ICONS

Viewable icons are based on user permissions.

Select Stream: Selects the viewable video stream that displays in live view (Primary, Secondary, QuickView, or Event) and selects
unicast or multicast and throttle settings.

Maximize Viewing Area: Scales the image to the full size of the browser. To resize the video pane to normal view, click the
Show Toolbar button in the upper-right corner of the window.

Show Toolbar: Returns the window to normal view. This icon is only available after the window has been set to maximize the
viewing area.

Open Stream in New Window: Opens the video in a scalable, independent window. Opening the video in a separate window allows
you to view the video while other applications are running. This window can be minimized, maximized, or closed using the title bar
buttons of the active window. The window can also be resized by dragging a corner of the window.

Take a Snapshot: Captures the image displayed in the video pane and saves it as a JPEG file.

Recalibrate Now: Immediately closes the shutter to improve video quality by removing noise from the image. During recalibration, the

video will freeze for approximately one-third of a second, and a small number of video frames will be lost.

Delay Recalibration: Delays closing the shutter by one minute.

SELECTING A STREAM

1. Click the Select Stream button.

2. Select one of the following streams from the Select Stream page:

Primary Stream: To select this stream, click the button next to Primary Stream.

Secondary Stream: To select this stream, click the button next to Secondary Stream.

QuickView Stream: To select this stream, click the button next to QuickView Stream.

Event Stream: To select this stream, click the button next to Event Stream.

NOTE: If the secondary stream has not been configured, only Primary Stream, Event Stream, and QuickView Stream are available.

3. Configure the display settings for the selected stream. Available display settings are determined by the video compression of the selected
stream:

H.264 compression: For the Primary Stream or Secondary Stream. You can also select Unicast or Multicast from the Transmission drop­down menu.

JPEG compression: For the Secondary Stream or QuickView Stream, select Images Per Second (IPS) from the Throttle drop-down menu.

4. Click the Select button to save the stream settings.

Primary Stream and Secondary Stream

The Primary Stream and Secondary Stream are video streams that include compression, resolution, image rate, and bit rate settings. The streams
can be set up using a video configuration preset or they can be customized using the video configuration settings.

A video preset is a predefined video configuration that offers a good balance between video performance and bandwidth usage. For easy stream
configuration, use the Video Presets page located in the drop-down menu of the A/V Streams tab.

To customize the Primary Stream or Secondary Stream, select the Settings page and then use the Video Configuration page located in the drop­down menu of the A/V Streams tab. Configurable settings include the stream name, compression, resolution, image rate, bit rate, and I-frame

C1316M-C (8/13) 17

interval of the video streams. The default names for the streams are Primary Stream and Secondary Stream; however, if these stream names are
changed, the new names replace the default names (Primary Stream and Secondary Stream) on the Select Stream page.

QuickView Stream

The QuickView Stream is a predefined JPEG video stream with a lower resolution. This low resolution, low frame rate stream is available when
the Imaging tab settings are being configured. This allows users to view changes to exposure, white balance, and other settings as they are
configured and before the settings are saved.

The QuickView Stream is also ideal for users who are connected to a network with processor bandwidth limitations that might cause a high
resolution, high frame rate video stream to pause or appear pixilated.

The aspect ratio of the QuickView Stream mirrors that of the Primary Stream.

Event Stream

The Event Stream displays a list of alerts triggered by a running analytic behavior. The alert includes a screen capture, the profile that was
triggered, and the zone where the alert was detected. For the Event Stream to work you must have an analytic behavior profile running. To set up
and run analytic behaviors, profiles, and zones, use the Analytic Configuration page located in the drop-down menu of the Events tab.

Unicast

A unicast transmission sends a separate video stream to each user that is requesting data. Although multiple users might request the same data
from the camera at the same time, duplicate video streams are transmitted to each user. Every unicast user that connects to the camera
consumes additional processing power, which limits the number of simultaneous users who can access the camera.The camera supports a
maximum of 20 simultaneous users.

Multicast

A multicast transmission sends data to multiple users at the same time using one transmission stream. Each multicast user that connects to the
camera consumes no additional processing power; therefore, multicast video streams can be sent to an unlimited number of simultaneous users.

TAKING A SNAPSHOT

1. Click the Take a Snapshot button.

2. A dialog box opens, allowing you to open or save the file.

3. Select one of the following options:

Open: Your computer’s photo editing program opens and displays the screen image. This function is available only when using
Microsoft

Save: The image is saved as a JPEG file at the location you specify.

Cancel: The captured image is not opened or saved and the dialog box closes.

NOTE: If you are using JPEG, the captured image is the size of the largest MJPEG stream. If you are using MPEG-4 or H.264, the image is

captured using the QuickView Stream, which is a low resolution image.

SETTINGS PAGE

Depending on user permissions, the Settings page allows you to manage camera system and network settings, set up users, configure events,
and control the camera imaging and streams.

®

Internet Explorer® 7.0 (or later) or Mozilla® Firefox® 3.0 (or later).

NOTE: The Settings menu might not be available if the user does not have permission to access this feature.

18 C1316M-C (8/13)

ACCESSING THE CAMERA MENUS

1. Log on to the camera.

2. Click the Settings link in the navigation bar located in the upper-right corner of the page; a list of menu tabs appears.

3. Place your mouse pointer over a tab to display a list of submenus.

SYSTEM TAB

Use the System tab to change general system settings, configure the time settings, set up the text overlay for the live view, configure backup and
restore, display system information, and access snapshots generated by event handlers.

General System Settings

The general system settings page includes configurable fields for the device name, time settings, and text overlay settings. The device name is
the user-friendly description of the camera displayed in the gray area near the top of screen. The time server is an external server that uses
Network Time Protocol (NTP) to synchronize the camera date and time settings. The text overlay settings allow you to customize the appearance
of the video by displaying overlays such as the device name, or the date and time at the top or bottom of the video stream.

You can also use the general system settings page to turn the camera’s LEDs on or off and to configure the Simple Mail Transfer Protocol (SMTP)
server to send an email notification when an event handler is activated.

NOTE: Contact your network administrator for information on configuring email notification on your local network.

You can also use the general system settings page to generate a system log, reboot the camera, or restore the camera’s factory default settings.

Licensing Settings

The Licensing page provides an interface to add specialized features to your Sarix® device. Refer to license-specific documentation for more
information about installing licenses and the effects that a license might have on your device.

Backup and Restore Settings

The backup and restore settings page includes configurable fields for backup and restore of camera settings. Once the camera settings have
been configured for optimal scene display, use the backup feature to save the camera settings. If the camera settings are changed and
inadvertently result in a less desirable image, use the restore feature to restore the camera to the previously saved settings.

NOTE: This feature is not intended for the configuration of multiple units or for firmware upgrades.

Information Settings

The information settings page includes read-only fields for the firmware version, hardware version, model number, and serial number of the
camera. This information is typically required by Pelco Product Support for troubleshooting purposes.

Snapshot Viewer

The Snapshot Viewer page displays a list of snapshots saved to the SD card when a “Write JPEG to SD Card” event handler is activated. From
this page, you can open, download, or delete snapshots from the SD card. There are 100 snapshots displayed per page.

CHANGING THE DEVICE NAME

1. Place your mouse pointer over the System tab.

2. Select General Settings from the drop-down menu.

3. Click the Device Name box and highlight the text.

4. Type a user-friendly name into the Device Name box (2 to 63 characters). A user-friendly name makes it easier to recognize the device on
the network. Examples of user-friendly names are Front Door, Lobby, or Parking Lot.

5. Click Save to save the new device name, or click Reset to restore to the previously saved device name.

C1316M-C (8/13) 19

CONFIGURING DHCP TIME SERVER SETTINGS

The Auto setting allows the device to discover and synchronize with a network time server over IPv4 or IPv6. If a network time server is not
available for discovery on the network, select the Manual time server setting.

1. Place your mouse pointer over the System tab.

2. Select General Settings from the drop-down menu.

3. Select Auto for the Time Server.

4. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

CONFIGURING MANUAL TIME SERVER SETTINGS

1. Place your mouse pointer over the System tab.

2. Select General Settings from the drop-down menu.

3. Select Manual for the Time Server.

4. Type the IP address or hostname of the time server in the Time Server box.

5. Configure the Time Zone by selecting the continent and region that are closest to the camera’s location from the Time Zone drop-down
menus.

NOTE: If your location observes a form of daylight saving time, the system automatically changes the time on the associated dates.

6. You can also specify time using an offset from Greenwich Mean Time (GMT) if you do not make a selection from the Time Zone drop-down
menu.

7. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

CUSTOMIZING THE APPEARANCE OF THE TEXT OVERLAY

1. Place your mouse pointer over the System tab.

2. Select General Settings from the drop-down menu.

3. Set the Text Overlay settings:

Date/Time Overlay: Select Show to display the date and time in the live view overlay. The default setting is Hide.

Camera Name Overlay: Select Show to display the camera name in the live view overlay. The default setting is Hide.

4. Select the display position for the overlay from the Position drop-down menu. Selections include Top Right, Top Center, Top Left, Bottom
Right, Bottom Center, and Bottom Left.

5. If an overlay is set to Show, view the format of the overlay in the Overlay Format area.

6. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

GENERATING A SYSTEM LOG

1. Place your mouse pointer over the System tab.

2. Select General Settings from the drop-down menu.

3. Click the Generate System Log button.

4. A dialog box opens, allowing you to open or save the file.

5. Save the file to create a system log that can be used by Pelco Product Support for troubleshooting. Contact Pelco Product Support at
1-800-289-9100 (USA and Canada) or [phone] (international).

20 C1316M-C (8/13)

REBOOTING THE CAMERA

1. Place your mouse pointer over the System tab.

2. Select General Settings from the drop-down menu.

3. Click the Reboot Camera button to restart the camera.

NOTE: Rebooting the camera does not change the configured camera settings.

RESTORING ALL CAMERA DEFAULTS

WARNING: This process cannot be undone; all user and custom settings will be lost.

1. Place your mouse pointer over the System tab.

2. Select General Settings from the drop-down menu.

3. Click the Restore All Camera Defaults button to restore the camera’s factory default settings.

NOTE: If the device is not connected to a Dynamic Host Configuration Protocol (DHCP) network, the IP address settings for the device will be lost
and the server will not recognize the device. The default setting for the device IP address is DHCP On.

DOWNLOADING A FULL BACKUP OF CAMERA SETTINGS

1. Place your mouse pointer over the System tab.

2. Select Backup and Restore from the drop-down menu.

3. Click the Download Now button. A file download dialog box opens.

4. Click Save and specify where you want to save the file.

5. Click OK to save the backup file, or click Cancel to stop the operation.

UPLOADING A BACKUP FILE TO RESTORE CAMERA SETTINGS

1. Place your mouse pointer over the System tab.

2. Select Backup and Restore from the drop-down menu.

3. Click the Browse button. A file upload dialog box opens.

4. Select the file you want to upload.

5. Click the Open button.

6. Click the Upload and Restore button.

NOTE: Restoring a backup file restarts the camera.

7. Click OK to restore the backup file, or click Cancel to stop the operation.

C1316M-C (8/13) 21

NETWORK TAB

Use the Network tab to change the camera’s general network settings, select the Secure Sockets Layer (SSL) settings, enable Secure Shell (SSH),
configure 802.1x port security, and select Simple Network Management Protocol (SNMP) settings.

General Network Settings

The general network settings page includes configurable and read-only fields for IPv4 and IPv6 network communication settings. The port
settings determine the ports over which the camera communicates using HTTP, HTTPS, and RTSP protocols. The hardware address is read-only.

IPv4 settings must be configured for the device. You can enable or disable the IPv4 DHCP setting from the general network settings page. If DHCP
is set to On, the IP address, subnet mask, gateway, and DNS server settings are automatically assigned to the device and are read-only text. If
DHCP is set to Off, these settings must be manually configured. The default camera setting for DHCP is On.

SSL Settings

The SSL settings page includes SSL configuration modes and certificate generation. To ensure security on the Internet, all Web browsers provide
several security levels that can be adjusted for sites that use SSL technology to transmit data. SSL encrypts communications, making it difficult
for unauthorized users to intercept and view user names and passwords.

SSL requires signed certificates to determine if the Web browser accessing the camera has the required authentication. The camera can
generate a certificate signing request (CSR) that can be sent to a certificate authority for a signature (for example, VeriSign
a self-signed certificate using the Generate Self-Signed Certificate option.

®

), or it can generate

SSH Settings

The SSH settings page enables or disables SSH access to the camera. SSH is a user-enabled protocol that allows Pelco Product Support to log on
to and service the camera for advanced troubleshooting purposes. From the SSH settings page, users with the appropriate permissions can
enable or disable SSH access to the camera.

802.1x Settings

The 802.1x settings page enables or disables 802.1x port security, which authenticates devices that want to establish a point-to-point access
through a wired or wireless port using Extensible Authentication Protocol (EAP) protocols. This port-based authentication method prevents
unauthorized access to a Local Area Network (LAN) through a physical port. For example, when a device is connected to a network port, the
network switch asks the device for authentication. The device replies with its credentials. If the credentials are accepted, the network switch
opens the port for normal use. If authentication fails, the device is prevented from accessing information on the port.

SNMP Settings

The SNMP setting page includes SNMP configuration settings. SNMP is an application layer protocol used to manage TCP/IP-based networks
from a single workstation or several workstations. The camera supports SNMP v2c and v3 and can be configured to send traps.

CHANGING THE HOSTNAME

1. Place your mouse pointer over the Network tab.

2. Select General from the drop-down menu.

3. View the read-only hardware address.

4. Click the Hostname box and highlight the text.

5. Type a user-friendly name into the Hostname box (1 to 21 characters) using alphanumeric characters. A user-friendly name makes it easier
to recognize the device on the network. Numeric-only names are not allowed.

6. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

22 C1316M-C (8/13)

CHANGING THE HTTP PORT

NOTE: The HTTP port number must remain at the default setting of 80 when connecting to a Pelco video management system (VMS). If you are

connecting to a Pelco VMS, do not change the HTTP port setting.

1. Place your mouse pointer over the Network tab.

2. Select General from the drop-down menu.

3. Click the HTTP Port box and highlight the text.

4. Type a new port number for HTTP communications. The default setting is 80.

NOTE: Contact your network administrator before changing port settings to ensure they do not conflict with your network infrastructure.

5. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

CHANGING THE HTTPS PORT

NOTE: Before configuring the HTTPS port, set the SSL configuration mode to either Optional or Required and install a security certificate.

1. Place your mouse pointer over the Network tab.

2. Select General from the drop-down menu.

3. Click the HTTPS Port box and highlight the text.

4. Type a new port number for HTTPS communications. The default setting is 443.

NOTE: Contact your network administrator before changing port settings to ensure they do not conflict with your network infrastructure.

5. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

CHANGING THE RTSP PORT

NOTE: The camera uses the RTSP protocol to communicate with a video management system (VMS). Do not change the RTSP port unless you

are sure your VMS does not use the default RTSP port.

1. Place your mouse pointer over the Network tab.

2. Select General from the drop-down menu.

3. Click the RTSP Port box and highlight the text.

4. Type a new port number for RTSP communications. The default setting is 554.

NOTE: Contact your network administrator before changing port settings to ensure they do not conflict with your network infrastructure.

5. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

TURNING ON DHCP

The default Dynamic Host Configuration Protocol (DHCP) setting for the camera is DHCP On. If DHCP is set to Off, complete the following steps to
reset it to On.

1. Place your mouse pointer over the Network tab.

2. Select General from the drop-down menu.

3. Select On for DHCP.

4. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

NOTE: If the camera is not connected to a DHCP server but DHCP is set to On, the default IP address 192.168.0.20 on subnet mask 255.255.255.0
is automatically assigned to the camera. After the first camera is connected and assigned the default IP address, the system automatically looks
for other cameras on the auto IP address system and assigns IP addresses in sequential order as required. For example, if three cameras are
connected to a network without a DHCP server, the first camera is assigned address 192.168.0.20, the second camera is assigned address

192.168.0.21, and the third camera is assigned address 192.168.0.22.

C1316M-C (8/13) 23

CONFIGURING A STATIC IPV4 ADDRESS

WARNING: Contact your network administrator to avoid any network conflicts before setting or changing the IP address of the device.

1. Place your mouse pointer over the Network tab.

2. Select General from the drop-down menu.

3. Select Off for the Dynamic Host Configuration Protocol (DHCP).

4. Change the following network settings as required:

IP Address: The address of the camera connected to the network.

Subnet Mask: The address that determines the IP network to which the camera is connected (relative to its address).

Gateway: The router that accesses other networks.

DNS Servers: The addresses of the dedicated servers that translate the names for Web sites and host names into numeric IP addresses.

5. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

CONFIGURING IPV6 ADDRESS SETTINGS

Your Sarix device supports IPv6 in conjunction with IPv4 configurations; the device does not support IPv6-only network deployments. The device
will accept up to sixteen IPv6 addresses, three IPv6 DNS servers, and three IPv6 gateways.

There are two configuration modes for IPv6 address assignments:

Auto: Enables automatic configuration using router advertisement. Additional configuration can be provided over DHCPv6 (if available on your
network). Selecting Auto mode still allows you to manually configure additional IPv6 addresses, DNS servers, and gateways.

Manual Only: Provides a link-local IPv6 address for the device and allows you to assign up to 16 static IPv6 addresses to the device.

1. Place your mouse pointer over the Network tab.

2. Select General from the drop-down menu.

3. Select On for IPv6.

4. Select a Configuration Mode from the drop-down box. Selecting Auto allows the device to configure the remaining IPv6 settings
automatically, rendering the remaining steps optional.

5. (Optional) Provide static, unicast addresses in the Manual IP Addresses box. Each address requires a prefix, and it must be input using the
format prefix/IPv6Address. Manual IP addresses without prefix information will be rejected.

6. (Optional) Provide the addresses of DNS servers that are not configured automatically in the Manual DNS Servers box.

7. (Optional) Provide the addresses of gateways that are not configured automatically in the Manual Gateways box.

NOTES:

• The device will not accept multicast, localhost, or undefined IPv6 addresses.

• Link-local addresses are not supported for DNS.

• Manually specified DNS servers supersede automatically discovered DNS servers.

• Manually specified DNS servers are not validated by the device; verify any manually specified DNS servers before saving IPv6 settings.

• Manually specified gateways must be on the same network as the devices’s IPv6 addresses. Behavior for a gateway that is not on the same
network as the device’s IPv6 addresses is undefined.

• Some video management systems (VMS), including Pelco VMS systems, do not support connections to cameras and encoders over IPv6.

24 C1316M-C (8/13)

SELECTING THE SECURE SOCKETS LAYER MODE

1. Place your mouse pointer over the Network tab.

2. Select SSL from the drop-down menu.

3. Select one of the following modes:

Disabled: Turns off access to the Web client through SSL. Sensitive data is not encrypted during transmission. The default setting is
disabled.

NOTE: If the SSL mode is set to disabled, you cannot access the camera using a URL that begins with an “https:” protocol. Your Web
browser displays an error message if you do not type the camera URL correctly.

Optional: A signed SSL certificate must be installed, but a secure URL that begins with the protocol name “https:” is optional when
accessing the camera. You can also access the camera using a standard URL with the “http:” protocol, but sensitive data is not encrypted
during transmission. To ensure that sensitive data is encrypted, you must use a secure URL with the “https:” protocol.

Required: A signed Secure Sockets Layer (SSL) certificate must be installed, and a secure URL that begins with the protocol name “https:”
must be used to access the camera. Sensitive data is always encrypted during transmission. A URL that begins with the “http:” protocol
rather than the “https:” protocol is redirected to the secure URL automatically.

NOTE: Beginning with firmware version 1.8.2, this mode cannot be modified in the Web browser. To select or clear the Required mode, you
must use the ONVIF or Pelco API call. Doing so avoids placing the camera into a mode in which it would no longer work with a connected
VMS system.

Generating a Certificate Request

1. Place your mouse pointer over the Network tab.

2. Select SSL from the drop-down menu.

3. Click the Install New Certificate button located at the bottom of the SSL Configuration page. The Select Certificate Install Method buttons
appear on the page.

4. Select Generate Certificate Request, and then click Next. The Generate Certificate Signing Request form opens.

5. Fill in all of the fields, and then click Generate Request. The following progress message appears on the page: “Generating certificate
signing request, please wait.”

6. Send the CSR, which looks like an encrypted block of undecipherable text, to a third-party certificate authority of your choice for a
signature. You will receive a signed certificate.

7. Click Choose File and browse to locate the certificate on your computer.

8. Click Open once you locate and select the certificate.

9. Click Upload Certificate to upload the signed certificate to the device.

10. After the certificate is uploaded, select the desired mode.

11. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

NOTE: Depending on the third-party certificate authority that signed your certificate, you might need to renew your certificate after a specified
amount of time. Consult the certificate authority for more details.

Generating a Self-Signed Certificate

1. Place your mouse pointer over the Network tab.

2. Select SSL from the drop-down menu.

3. Click the Install New Certificate button located at the bottom of the SSL Configuration page. The Select Certificate Install Method buttons
appear on the page.

4. Select Generate Self-signed Certificate and then click Next. The Generate Self-signed Certificate form opens.

5. Fill in all of the fields, and then click the Generate Certificate button.

C1316M-C (8/13) 25

6. After the certificate is uploaded to the device, select the desired mode.

7. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

NOTE: Self-signed certificates are valid for one year. The certificate’s expiration date is listed in the “Valid from” and To fields in the Certificate
section of the window. If the certificate has expired and you attempt to access the camera using a secure URL, the Web browser displays a
message. Repeat this procedure to generate and upload a new certificate.

ENABLING SECURE SHELL

1. Place your mouse pointer over the Network tab.

2. Select SSH from the drop-down menu.

3. Select the Enabled check box.

4. Click the Password box and type a password (4 to 16 alphanumeric characters). Passwords are case-sensitive.

NOTE: The default user name is “root” and cannot be changed. The user name and password are required when accessing the camera
through a third-party SSH client.

5. Click the Re-type Password box and retype your password.

6. Click the Save button to save the password and enable SSH, or click the Reset button to clear all of the information you entered without
saving it.

CONFIGURING THE 802.1X PORT SECURITY SETTINGS

WARNING: To prevent network conflicts, contact your network administrator before configuring the 802.1x port security settings.

1. Place your mouse pointer over the Network tab.

2. Select 802.1x from the drop-down menu.

3. Select On for the 802.1x port security. The default setting for 802.1x port security is Off.

4. Select the Extensible Authentication Protocol (EAP) method from the Protocol drop-down menu. Supported EAP methods include EAP-MD5,
EAP-TLS, EAP-TTLS, EAP-PEAP, and EAP-FAST.

5. Type the information required for the selected 802.1x EAP method.

6. Connect the PC to a 802.1x secured switch that has the same EAP method.

7. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

26 C1316M-C (8/13)

SELECTING SNMP SETTINGS

WARNING: The Simple Network Management Protocol (SNMP) settings are advanced controls. Contact your network administrator to

obtain the required information to configure SNMP settings.

1. Place your mouse pointer over the Network tab.

2. Select SNMP from the drop-down menu.

3. Select the SNMP version to configure: SNMP V2c or SNMP V3. The default setting is No SNMP Server, which disables the SNMP
configuration.

NOTE: SNMP V2c and SNMP V3 configuration settings are independent of each other, but only one SNMP version can be active at a time.

CONFIGURING SNMP V2C

1. Place your mouse pointer over the Network tab.

2. Select SNMP from the drop-down menu.

3. Select SNMP V2c for the SNMP version.

4. Type the community name in the Community String box. The default name for the Community String is ”public.”

5. Configure the Trap Configuration settings:

Address: Type the host name or IP address of the trap server.

Community String: Type the community name for the trap server.

6. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

CONFIGURING SNMP V3

1. Place your mouse pointer over the Network tab.

2. Select SNMP from the drop-down menu.

3. Select SNMP V3 for the SNMP version.

4. Type the SNMP user name in the SNMP user box.

5. Select the encryption algorithm for authentication from the Authentication drop-down menu. Support authentication settings include None,
MD5, or SHA. If you use authentication method MD5 or SHA, type a password in the box to the right of the selected Authentication
encryption.

6. Select the privacy encryption algorithm setting from the Privacy drop-down menu. Supported encryption settings include None, DES, or
AES. If you use privacy method DES or AES, type a password in the Privacy text box.

7. Type the host name or IP address of the trap server in the Address box under Trap Configuration.

8. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

C1316M-C (8/13) 27

IMAGING TAB

Use the Imaging tab to change the camera’s general image settings, configure presets and preset tours, or configure positioning settings.

General Imaging Settings

General imaging settings include adjustments for the thermal color palette, sharpness, image enhancement, and recalibration.

The color palette programs the specific range of colors to represent the temperatures in the thermal image. These colors are not calibrated to a
specific temperature; rather, they represent the temperature variations within the thermal image.

The sharpness setting sharpens details in a scene. The image enhancement setting adjusts the thermal contrast range and detail of the image
definition of objects in the image; a higher image enhancement setting results in higher contrast and greater image detail with increased noise.
The noise filtering setting adjusts the strength of the automatic noise filter: lower noise filtering results in greater image detail with more noise,
and higher noise filtering results in lower noise and image detail. It is recommended that you configure the image enhancement setting before
the noise filtering setting.

Recalibration closes the shutter to improve video quality by removing noise from the image.

WARNINGS:

• When using the sharpness or image enhancement settings, be aware that picture noise, although unnoticeable to the eye, will

increase and may cause compression rate changes in DVRs, NVRs, and network devices.

• During recalibration, the video will freeze for approximately one-third of a second, and a small number of video frames will be lost.

SELECTING THE COLOR PALETTE

1. Place your mouse pointer over the Imaging tab.

2. Select General from the drop-down menu.

3. Select one of the options from the Color Palette drop-down menu.

CHANGING THE SHARPNESS

1. Place your mouse pointer over the Imaging tab.

2. Select General from the drop-down menu.

3. Move the Sharpness slider to the right to increase the clarity of detail in a scene; move the slider to the left to decrease the clarity of detail
in a scene. The sharpness range is 0 (zero) to 100; the default setting is 50.

CHANGING THE IMAGE ENHANCEMENT

1. Place your mouse pointer over the Imaging tab.

2. Select General from the drop-down menu.

3. Move the Image Enhancement slider to the right to increase the contrast and detail in the scene; the noise in the scene increases. Move the
Image Enhancement slider to the left to decrease the contrast and detail in the scene; the noise in the scene dereases.

CONFIGURING NOISE FILTERING

NOTE: It is recommended that you configure image enhancement settings to produce the desired image contrast and detail before configuring

the noise filtering setting.

1. Place your pointer over the Imaging tab.

2. Select General from the drop-down menu.

3. Move the slider to the right to reduce noise in the image at the cost of image detail; move the slider to the left to maintain higher image
detail at the cost of increased video noise.

28 C1316M-C (8/13)

CONFIGURING THE RECALIBRATION SETTINGS

1. Place your mouse pointer over the Imaging tab.

2. Select General from the drop-down menu.

3. Select one of the following Recalibration settings:

Auto: Closes the camera shutter to automatically recalibrate as frequently as needed based on the camera conditions.

Periodic: Closes the camera shutter to recalibrate as often as specified.

Manual: Closes the camera shutter to recalibrate only when the user clicks the recalibrate buttons on the Live View page.

4. If you selected the periodic recalibration setting, click in the “Recalibrate every” box and type the frequency at which the camera should
recalibrate.

A/V STREAMS TAB

Use the A/V Streams tab to configure the video and audio streams for the camera. The A/V Streams tab includes video presets settings, and
video and audio configuration.

Video Presets Settings

The video preset settings page includes three fully-configured video presets, High, Medium, and Low, which include primary and secondary video
stream settings for easy setup. These presets can also be used as a starting point for a custom video configuration. These preset configurations
vary depending on camera model.

Video Configuration Settings

The video configuration settings page allows you to customize the compression, resolution, image rate, bit rate, and I-frame interval of the video
streams. The default names for the streams are Primary Stream and Secondary Stream. Although each stream can be configured independently,
the settings of one stream can limit the options available to the other stream, depending on the processing power used.

NOTE: Always configure the primary stream before the secondary stream. The primary stream should always be the most resource-intensive of
the streams.

SELECTING A VIDEO PRESET CONFIGURATION

1. Place your mouse pointer over the A/V Streams tab.

2. Select Video Presets from the drop-down menu.

3. Click the button next to the desired video preset stream configuration.

4. Click the Save button to save the settings, or click the Reset button to clear your selection without saving it.

CONFIGURING A CUSTOM VIDEO STREAM CONFIGURATION

1. Place your mouse pointer over the A/V Streams tab.

2. Select Video Configuration from the drop-down menu.

3. Click both of the Clear buttons to delete the primary and secondary streams settings.

4. Optional: In the Primary Stream section, type a user-friendly name in the Name box (2 to 64 characters). A user-friendly name makes it
easier to recognize the stream (for example, Live and Recording).

5. Configure the Compression Standard, Resolution, Image Rate, Bit Rate, and I-frame Interval settings for the primary stream.

NOTE: The compression standard, resolution, image rate, bit rate, and I-frame interval settings are dependent on each other. You must first
decide the priority setting before you configure a stream. For example, if you want an image rate of 30 ips, set the image rate before you
configure the other settings.

6. Configure QoS (DSCP) Codepoint, Endura Signing, Profile, and GOP Structure.

C1316M-C (8/13) 29

7. Repeat steps 3 to 5 for the Secondary stream.

8. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Compression Standards

JPEG: A commonly used video compression scheme. JPEG has the least impact on the camera’s processor, but it requires the most bandwidth.

MJPEG: Motion JPEG has the same characteristics as JPEG but differs in its mode of transfer (RTP).

H.264: Also known as MPEG-4 Part 10 or Advanced Video Coding (AVC), H.264 is one of the most widely used compression, recording, and

distribution methodologies for High Definition (HD) video. It is used in Blu-ray™ video players and by companies that transmit HD video or movies
over the internet and by satellite. H.264 is the most processor-intensive compression standard, but it requires the least amount of bandwidth.

Image Rate

The image rate is the number of images per second (ips) available for the video stream configuration. Available image rates depend upon the
model of the device that you are using.

NOTE: The maximum image rate setting might not be obtainable due to the compression standard and the resolution of the stream.

Bit Rate

The bit rate is the quality of the video stream (rendered in kilobits per second). The higher the value, the higher the video quality and bandwidth
required.

NOTE: When you change any of the video stream configuration settings, the camera automatically adjusts the bit rate. If you manually reduce
the bit rate lower than the camera's automatic setting, the image quality might be reduced and the stream selection options might be limited.

I-Frame Interval

The I-frame interval configures the number of partial frames that occur between full frames in the video stream. For example, in a scene where a
door opens and a person walks through, only the movements of the door and the person are stored by the video encoder. The stationary
background that occurs in the previous partial frames is not encoded, because no changes occurred in that part of the scene. The stationary
background is only encoded in the full frames. Partial frames improve video compression rates by reducing the size of the video. As the I-frame
interval increases, the number of partial frames increases between full frames. Higher values are recommended only on networks with high
reliability. This setting is available only with H.264.

Quality of Service for Differentiated Services Code Point

Quality of Service (QoS) for Differentiated Services Code Point (DSCP) is a code that allows the network to prioritize the transmission of different
types of data. This setting is available only with H.264.

NOTES:

• If you are not familiar with DSCP, contact your network administrator before changing this setting.

• Your network must be configured to use QoS. If you are unsure if your network is QoS-aware, contact your network administrator.

Endura Signing

Enabling the Endura Signing feature allows an Endura® system to authenticate video from an Endura recorded stream. This setting is available
only with H.264.

30 C1316M-C (8/13)

SELECTING THE AUDIO CONFIGURATION SETTINGS

To use audio with the camera if it does not have built-in audio support, you must connect an audio device to the accessory port. Once the device
is connected, audio can only be enabled through the primary stream.

Audio and video may not be synchronized when viewing and listening to the primary stream through a Web browser. You may experience a
three-second delay in video when viewing the primary stream with audio.

NOTE: Improper use of audio/visual recording equipment may subject you to civil and criminal penalties. Applicable laws regarding the use of
such capabilities vary between jurisdictions and may require, among other things, express written consent from the recorded subjects. You are
solely responsible for ensuring strict compliance with such laws and for strict adherence to any/all rights of privacy and personalty.

1. Place your mouse pointer over the A/V Streams tab.

2. Select Audio Configuration from the drop-down menu.

3. Select Enabled in the Audio section.

4. Select the audio device setting from the Audio Device drop-down box.

Native Line In: Enables audio from a microphone connected to the audio-in connector.

5. Select the sample rate from the Sample Rate drop-down box. The sample rate is the quality of the audio stream (rendered in hertz per
second). The higher the value, the higher the audio quality. Available sample rate settings are 8000 Hz and 12000 Hz. The default setting is
8000 Hz.

6. Select the encoding method for the audio device from the Encoding drop-down box. Available encoding methods are PCMU, PCMA, and
PCM16. The default setting is PCMU.

7. If required, click the button next to Mute to mute the audio device.

NOTE: Do not use the mute button on an audio device, as it will override the audio software settings. To mute the audio device, select
Mute located on the Audio Configuration page.

8. Set the sensitivity of the input level by moving the Input Level slider. Move the slider to the right to increase the sensitivity level; move it to
the left to decrease the sensitivity level. For example, if the camera is installed in a noisy environment or the connected microphone has a
built-in line amplifier, set the sensitivity to a low setting. The setting range is 0 to 100.

9. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

C1316M-C (8/13) 31

USERS TAB

Use the Users tab to create and manage user accounts and to change the way the camera manages the users settings.

General Users Settings

The general users settings page sets the public user access level. This access level is a predefined set of user permissions that allows the
camera to be accessed without logging on. Available permissions depend on the model of the camera that you are using.

The general users settings page also allows you to change the way the camera manages users and groups. These settings can be managed on a
camera-to-camera basis (local mode) or by using a centralized server to apply changes to multiple cameras (remote mode).

Users Settings

The users settings page defines the access levels assigned to individuals logged on to the camera. Use this page to create, modify, or delete user
accounts for Administrators, Managers, Operators, and Viewers. User accounts are created to limit permissions.

SELECTING THE USERS AND GROUPS SETTINGS

1. Place your mouse pointer over the Users tab.

2. Select General Settings from the drop-down menu.

3. Select one of the following Authentication modes:

Open Authentication: Allows users to view video and use the camera API without validating user credentials. When Open Authentication
is selected, you can select “Require password for PTZ control” to limit PTZ control to authenticated users.

Closed Authentication: Requires users to possess valid credentials to view video and access the camera API. Before selecting Closed
Authentication, ensure that your video management system supports Closed Authentication mode.

4. Select one of the following User and Group Management modes to manage permissions of users and groups:

Local Mode: The camera manages users and groups locally. Any changes to users and groups affect only the camera that you are
accessing. The default setting is Local Mode.

Remote Mode: The camera authenticates and manages users through a Lightweight Directory Access Protocol (LDAP) server supported by
Microsoft
Selecting Remote Mode disables Local Mode and all management is done on the server.

5. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

®

Active Directory®. This allows administrators to tie cameras and group permissions into existing single sign-on services (SSO).

WARNING: Remote Mode settings are advanced controls. Contact your network administrator to obtain the required information to
configure remote settings.

32 C1316M-C (8/13)

ENABLING REMOTE MODE

1. Place your mouse pointer over the Users tab.

2. Select General Settings from the drop-down menu.

3. Select Remote Mode. The default setting is Local Mode.

4. Type the IP address or host name of the LDAP server in the LDAP Server box.

5. Type the port over which the camera communicates with the LDAP server in the LDAP Port box. The default port for LDAP communications
is 389.

6. Type the distinguished name (DN) that is the basis for LDAP searches in the Base DN box.

7. Provide the template to format the user name (provided when the user logs on to the camera) for searches in the LDAP directory in the Bind
DN Template box.

8. Provide the LDAP search query for users found in the base DN in the Search Template box. The search must match an entry in the LDAP user
record to the bind name (user name).

9. Type the Group Mappings for each of the camera’s four user groups:
a. Type the common name (CN) and DN for the group of users to whom you want to grant admin access in the Admins box.

b. Type the CN and DN for the group of users to whom you want to grant manager access in the Managers box.

c. Type the CN and DN for the group of users to whom you want to grant operator access in the Operators box.

d. Type the CN and DN for the group of users to whom you want to grant viewer access in the Viewers box.

10. Type the credentials of a user who can be authenticated through the LDAP server in the User and Password boxes.

NOTE: Remote Mode (LDAP authentication) will not be enabled if you leave these boxes blank or do not provide valid credentials; this
ensures that you cannot lock yourself out of the camera with invalid or incorrect LDAP settings.

11. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

CREATING A NEW USER

1. Place your mouse pointer over the Users tab.

2. Select Users from the drop-down menu.

3. Select the Access Level for the user:

Admins: Permissions include access to all camera settings.

Managers: Permissions include access to all settings except this user cannot modify user permissions or restore factory default settings.

Operators: Permissions include view video and pan and tilt functions.

Viewers: Permissions include view video and use the API.

4. Click the Username box and type a user name (2 to 32 alphanumeric characters). User names are not case-sensitive and are saved in
lowercase characters.

5. Click the Password box and type a password (4 to 64 alphanumeric characters). Passwords are case-sensitive.

6. Click the Retype Password box and retype your password.

7. Click the Save button to save the settings and create a new user (the new user profile appears in the Users box on the left side of the page),
or click the Reset button to clear all of the information you entered without saving it.

C1316M-C (8/13) 33

EDITING A USER

1. Place your mouse pointer over the Users tab.

2. Select Users from the drop-down menu.

3. Click the user profile that you want to edit from the Users box on the left side of the page.

4. If required, select a different Access Level for the user.

5. Double-click each of the password boxes to highlight the text. Type the new information in each password box.

NOTE: The Username cannot be modified; this box is read-only.

6. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

DELETING A USER

1. Place your mouse pointer over the Users tab.

2. Select Users from the drop-down menu.

3. Click the user profile that you want to delete from the Users box located on the left side of the page.

4. Click the Delete User button. A dialog box opens and the following message appears “Are you sure you want to delete this user?”

5. Click OK. The user profile is deleted from the Users box.

NOTE: The “admin” user cannot be deleted.

EVENTS TAB

Use the Events tab to configure camera events and analytics.

Events are activated by user-defined event sources that tell the device how to react when an event occurs. Event handlers are the actions that
the device takes when an event occurs. For example, a system source can be configured to send email to an operator if the system shuts-down
and restarts.

Sources Settings

The sources settings page defines the camera functions that are automatically triggered by an event source. The camera supports Alarm,
Analytics, Park Action, System, and Timer sources. The Alarm source is the camera input for an external signaling device, such as a door contact
or motion detector. The Analytics source triggers when any configured behavior is detected. The System source is activated when the camera
restarts. The Timer source is a user-defined event that activates an event after a specified amount of time.

Handlers Settings

The device supports a Send Email handler, a “Write JPEG to SD Card” handler, an “Upload JPEG to FTP Server” handler, and an Open/Close Relay
handler. The Send Email handler sends an email to a defined email address when an event is activated. The “Write JPEG to SD Card” saves a
JPEG of the activated event to an SD card. The “Upload JPEG to FTP Server” saves a JPEG of the activated event to a defined FTP server. The
Open/Close Relay handler sends a signal to an external device when an alarm or relay is triggered. The Run Tour handler starts a user-defined
preset tour.

NOTE: The Pelco Alarm accessory must be connected to the camera’s accessory port for Open/Close Relay to work.

Analytic Configuration Settings

Pelco analytics can be configured and enabled using a standard Web browser. The device is preloaded with user-configurable behaviors and is
capable of running several behaviors at the same time. The number of behaviors is limited to the available processing power of the device.
Available processing power is determined by the settings for compression standards, resolution, image rate, bit rate, and analytic configuration.

Pelco analytics are also compatible with Endura
documentation for instructions on how to configure and enable Pelco analytics.

®

or a third-party system that supports alarms using Pelco’s API. Refer to the specific product

NOTE: Analytic alerts can be seen in the event stream, but alarms are only transmitted through Pelco’s API.

34 C1316M-C (8/13)

Models are also available with ObjectVideo® (OV) Suites. OV Suites require an OV ready-compliant system with an OV Ready™ video
management system to configure and enable the OV Analytic Suites that are preloaded on the camera. Refer to the ObjectVideo documentation
for instructions on how to configure and enable OV analytics.

Pelco analytics include the following behaviors:

Adaptive Motion: Detects and tracks objects that enter a scene and then triggers an alarm when the objects enter a user-defined zone. The
objects are monitored until they exit the scene.

Camera Sabotage: Detects contrast changes in the field of view. An alarm is triggered if the lens is obstructed with spray paint, a cloth, or
covered with a lens cap. Any unauthorized repositioning of the camera also triggers an alarm.

Loitering Detection: Identifies when people or vehicles remain in a defined zone longer than the user-defined time allows. This behavior is
effective for real-time notification of suspicious behavior around ATMs, stairwells, and school grounds.

Object Counting: Counts the number of objects that enter a defined zone or cross a defined trip wire. This behavior can be used to count people
at a store entrance/exit or inside a store where the traffic is light.

Stopped Vehicle: Detects vehicles stopped near a sensitive area longer than the user-defined time allows. This behavior is ideal for parking
enforcement, suspicious parking, traffic lane breakdowns, and vehicles waiting at gates.

SOURCES

An event is a preconfigured camera function that is activated automatically by an event source. The camera supports the following types of event
sources:

Alarm: If the Pelco Alarm accessory is connected to the device’s accessory port, the device can support alarm and auxiliary relay sources.

Analytics: An analytic source will activate a user-defined event handler when an analytic alert is detected.

System: A system source activates a user-defined event handler when the camera restarts.

Tim er: A timer source activates a user-defined event handler after a specified amount of time.

Creating an Alarm Event Source

1. Place your mouse pointer over the Events tab.

2. Select Sources from the drop-down menu.

3. In the New Event Source section of the window, click the Name box and type a user-friendly name (2 to 23 alphanumeric characters).

4. Select Alarm from the Type drop-down menu.

5. Select PCP from the Alarm Bank drop-down menu.

6. Select the alarm you want to trigger when an event occurs from the Alarm drop-down menu.

7. Move the Dwell Time slider to set the amount of time in seconds that the alarm is active. The dwell time range is 0.1 to 25 seconds;
the default setting is 0.1.

8. Select either Normally Open or Normally Closed from the Polarity drop-down menu.

9. Select either True or False from the Supervised drop-down menu.

10. Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

C1316M-C (8/13) 35

Creating an Analytics Event Source

1. Place your mouse pointer over the Events tab.

2. Select Sources from the drop-down menu.

3. In the New Event Source section of the window, click the Name box and type a user-friendly name (2 to 23 alphanumeric characters).

4. Select Analytics from the Type drop-down menu.

5. Select the Any Analytics check box to activate an event when any analytic event occurs.

6. Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Creating a System Event Source

1. Place your mouse pointer over the Events tab.

2. Select Sources from the drop-down menu.

3. In the New Event Source section of the window, click the Name box and type a user-friendly name (2 to 23 alphanumeric characters).

4. Select System from the Type drop-down menu.

5. Select the Boot check box to activate an event when the camera reboots.

6. Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Creating a Timer Event Source

1. Place your mouse pointer over the Events tab.

2. Select Sources from the drop-down menu.

3. In the New Event Source section of the window, click the Name box and type a user-friendly name (2 to 23 alphanumeric characters).

4. Select Timer from the Type drop-down menu.

5. Configure the frequency:
a. Select the time interval from the drop-down menu. Time intervals include seconds, minutes, hours, or days. The default setting is

seconds.

b. Click the Frequency box and type a number.

6. Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Editing an Event Source

1. Place your mouse pointer over the Events tab.

2. Select Sources from the drop-down menu.

3. Click the source profile that you want to edit from the Sources box located on the left side of the page.

4. Make your changes to the available fields in the Edit Event Source section of the window.

5. Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Deleting an Event Source

1. Place your mouse pointer over the Events tab.

2. Select Sources from the drop-down menu.

3. Click the source profile that you want to delete from the Sources box located on the left side of the page.

4. Click the Delete Source button. The source profile is deleted from the Sources box.

36 C1316M-C (8/13)

HANDLERS

Event handlers are the actions that the camera takes when an event occurs. The camera supports the following event handlers:

Send Email: Sends an email to a defined email address when an event is activated. The Simple Mail Transfer Protocol (SMTP) server must be
configured to accept the camera’s IP address.

Write JPEG to SD Card: Saves a JPEG of the activated event to an SD card. An SD card must be installed in the device for this handler to
function.

NOTE: The SD card must be formatted as FAT32. Other formats are not compatible with the camera.

Upload JPEG to FTP Server: Saves a JPEG of the activated event to a defined FTP server.

Open/Close Relay: Sends a signal to an external device when an alarm or relay is triggered.

Creating an Event Handler: Send Email

NOTE: To use email notification, the camera must be connected to a local area network (LAN) that maintains an SMTP mail server. Contact your

network administrator for information on configuring email notification on your local network.

1. Configure the SMTP server to send email.

2. Place your mouse pointer over the Events tab.

3. Select Handlers from the drop-down menu.

4. In the New Event Handler section of the window, click the Name box and type a user-friendly name (2 to 23 alphanumeric characters).

5. Select Send Email from the Type drop-down menu.

6. Click the boxes (To, From, Subject, and Message), and then type the necessary information in each box.

7. Select the JPEG Snapshot box if you want to send a JPEG as an attachment.

8. Select the Attach Raw Event Data box if you want the email to include extra data about the event. For example, select this box if the event
is triggered by an alarm and you want to receive data about the state, time, or type of alarm.

9. If you do not want the handler to activate every time an event occurs, set filters for the handler:
a. Select the day(s) of the week on which you want emails to be sent.

b. Type times in the Start and End boxes for the days you have selected. Use time values in 24-hour notation (for example, use 0800 for

8:00 a.m., 1600 for 4:00 p.m.).

c. If required, click the plus button (+) to add another time range.

10. Select one or more event sources to send an email when those event sources are activated.

11. Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Creating an Event Handler: Write JPEG to SD Card

1. Install an SD card in the SD card slot located on the back of the camera.

NOTE: The SD card must be formatted as FAT32. Other formats are not compatible with the camera.

2. Place your mouse pointer over the Events tab.

3. Select Handlers from the drop-down menu.

4. Click in the Name box and type a user-friendly name (2 to 23 alphanumeric characters).

5. Select the Write JPEG to SD Card option from the Type drop-down menu.

6. The JPEG files saved to the SD card will be given file names that correspond to the date and time of the event. Select a time standard from
the File Name drop-down menu.

7. Click in the Size limit box and type a number. Select Kilobytes, Megabytes, or Gigabytes from the Size Limit drop-down menu.

NOTE: Do not select a size limit that is larger than the amount of memory on the SD card. For example, if the SD card is 2 MB, do not
exceed 2 MB in the Size Limit box.

C1316M-C (8/13) 37

8. If you do not want the handler to activate every time an event occurs, set filters for the handler.
a. Select the day(s) of the week on which you want JPEGs saved to the SD card.

b. Type times in the Start and End boxes for the days you have selected. Use time values in 24-hour notation (for example, use 0800 for

8:00 a.m., 1600 for 4:00 p.m.).

9. Select one or more sources to save a JPEG to the SD card when those event sources are activated.

10. Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Creating an Event Handler: Upload JPEG to FTP Server

1. Place your mouse pointer over the Events tab.

2. Select Handlers from the drop-down menu.

3. In the New Event Handler section of the window, click the Name box and type a user-friendly name (2 to 23 alphanumeric characters).

4. Select the Upload JPEG to FTP Server option from the Type drop-down menu.

5. Click the Server box and type the server address (1 to 32 alphanumeric characters).

6. Click the Username box and type the user’s name (1 to 32 alphanumeric characters).

7. Click the Password box and type a password (4 to 16 alphanumeric characters).

8. Click the Base Path box and type the base path (1 to 32 alphanumeric characters). The base path is the path to your root directory.

9. Select a time standard from the File Name drop-down menu. The JPEG files uploaded to the FTP server are given file names that
correspond to the date and time of the event.

10. If you do not want the handler to activate every time an event occurs, set filters for the handler:
a. Select the day(s) of the week on which you want JPEGs saved to the FTP server.

b. Type times in the Start and End boxes for the days you have selected. Use time values in 24-hour notation (for example, use 0800 for

8:00 a.m., 1600 for 4:00 p.m.).

c. If required, click the plus button (+) to add another time range.

11. Select one or more sources to save a JPEG to the FTP server when those event sources are activated.

12. Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Creating an Event Handler: Open/Close Relay

1. Place your mouse pointer over the Events tab.

2. Select Handlers from the drop-down menu.

3. In the New Event Handler section of the window, click the Name box and type a user-friendly name (2 to 23 alphanumeric characters).

4. Select Open/Close Relay in the Type drop-down menu.

5. Select the serial number of the relay device from the Relay Bank drop-down menu.

6. Select either PCP or the serial number of the relay device from the Relay Bank drop-down menu.

7. Select the relay you want to trigger when an event occurs from the Relay drop-down menu.

8. Move the On Time slider to set the amount of time for the relay to remain open. The time range is 0.1 to 200 seconds; the default setting
is 0.1.

9. Move the Off Time slider to set the amount of time for the relay to remain closed. The time range is 0.1 to 200 seconds; the default setting
is 0.1.

10. Click the Pulse Count box and type a number. The pulse count is the number of relay pulses (number of on and off cycles).

11. If you do not want the handler to activate every time an event occurs, set filters for the handler:
a. Select the day(s) of the week on which you want the relay opened or closed.

38 C1316M-C (8/13)

b. Type times in the Start and End boxes for the days you have selected. Use time values in 24-hour notation (for example, use 0800 for

8:00 a.m., 1600 for 4:00 p.m.).

12. Select one or more event sources to open/close the relay when those event sources are activated.

13. Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Editing an Event Handler

1. Place your mouse pointer over the Events tab.

2. Select Handlers from the drop-down menu.

3. Click the handler profile that you want to edit from the Handlers box located on the left side of the page.

4. Make your changes to the available fields in the Edit Event Handler section of the window.

5. Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Deleting an Event Handler

1. Place your mouse pointer over the Events tab.

2. Select Handlers from the drop-down menu.

3. Click the handler profile that you want to delete from the Handlers box located on the left side of the page.

4. Click the Delete Handler button. The handler profile is deleted from the Handlers box.

Example Handler Filter Setup

If you do not want a handler to activate every time an event occurs, use the filter fields to limit handlers. In the following example, you only want
a handler activated when an event occurs after business hours. Your business is open Monday through Saturday, 8:00 a.m. to 6:00 p.m., and it is
closed on Sunday.

1. Create a handler for Monday through Saturday:
a. Select the day filter fields Monday through Saturday.

b. Type 0000 in the Start box and 0800 in the End box.

c. Click the plus button (+) to add another time range. Type 1800 in the second Start box and type 2400 in the second End box.

d. Select the source(s) that activates the handler.

e. Click the Submit button to save the handler.

2. Create a second handler for Sunday:
a. Select Sunday from the day filter fields.

b. Do not set a Start time or End time as this is a 24-hour event.

c. Select the source(s) that activates the handler.

d. Click the Submit button to save the second handler.

C1316M-C (8/13) 39

ANALYTIC CONFIGURATION

To configure an analytic behavior using a standard Web browser, you must create a profile, select the behavior for the profile, and then create the
zones to be monitored by the behavior.

NOTES:

• This section explains how to configure and enable Pelco analytics using a Web browser.

• Analytic alerts can be seen in the event stream, but alarms are only transmitted through Pelco’s API.

PROFILES

A profile defines the scene attributes of a behavior including scene type, background movement, and noise sensitivity. When configured properly,
a profile accurately detects behavior violations and decreases the number of triggered false alarms.

Profile Settings

For each behavior, you can create several custom profiles that contain different settings. These settings include:

Name: Assigns a descriptive name to the profile to make it easier to recognize and locate. Consider naming profiles based on their function.

Scene type: Sets the scene type of the profile. Available settings include Indoor and Outdoor.

Background: Defines the background movement of the scene. Available settings include Still or Noisy. If the background is stable, with few

moving objects, set the background to Still. If the background is busy, with many moving objects, select Noisy.

Fine tuning: Defines the zone violation sensitivity. Available settings include Conservative, Normal, or Aggressive. Conservative is the least
sensitive setting and reduces the amount of triggered false alarms, but it could miss some zone violations. Aggressive is the most sensitive
setting and detects all suspect objects, but it could trigger more false alarms. Normal falls between conservative and aggressive sensitivity and
provides moderate results.

Sensitivity: Defines the minimum motion an object can move before a behavior is activated. Settings range from 1 (low) to 10 (high). The
selected setting identifies any movement lower than the defined setting as noise, and ignores it. The higher the setting, the greater the chance
for a false alarm. A lower setting reduces the chance for a false alarm, but it could result in missed violations.

Creating a New Profile

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Click the New button located in the Select Profile section.

4. Type a descriptive name for the profile in the Name box located in the Profile Settings section.

NOTE: Consider naming profiles based on their function. A more descriptive name makes it easier to recognize and locate a profile.

5. Select the Camera preset, Scene type, Background, Fine tuning, and Sensitivity settings from the drop-down menus located in the Profile
Settings section.

6. Click the Calibrate Scene button to calibrate the scene.

NOTE: Set the perspective settings to reflect the camera’s angle. This information makes the object sizes you set on the next tab more
meaningful and helps reduce the number of false alarms.

7. Select the behavior for the profile from the Select Behaviors section.

8. Configure the settings for the behavior.

9. Click the Save button to save the profile. The new profile name appears in the Select Profile section. Or click the Reset button to clear all of
the information you entered without saving it.

40 C1316M-C (8/13)

Revising a Profile

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Select the profile name from the Select Profile section. The settings for the profile appear.

4. Make the required changes to the profile settings.

5. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Deleting a Profile

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Select the profile name from the Select Profile section.

4. Click the Delete button located in the Select Profile section.

5. A dialog box opens and the following message appears: “Are you sure you want to delete the profile [profile name]?”

6. Click the OK button to delete the profile.

CALIBRATE SCENE

Calibrate the scene to specify the dimensions for the objects of interest and to filter out objects that should not trigger an event or alarm. You
must calibrate the scene for both object height and object width.

NOTES:

• When setting object height, be sure to use an object that is similar in size to the objects you plan to track in the scene. For example, if you
want to detect people in a scene, use a person to calibrate the object height; if you want to detect vehicles in the scene, use a vehicle to
calibrate the object height.

• When setting object width, be sure to use a relatively wide, static object such as a road or an aisle. This will ensure that the scene is
calibrated with accurate perspective to reflect the camera’s angle.

Setting Object Height

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Click the profile you want to use from the Select Profile list.

NOTE: You must repeat scene calibration for each profile you want to use.

4. Click the Calibrate Scene button.

5. Click the “Set height” button.

6. Click the Pause button to freeze the video while you make adjustments on screen.

7. Place three objects of the same height at three different locations in the scene (near left, near right, and at a distance).

8. Using your mouse pointer, drag the three blue boxes on the screen to overlay the objects you have placed in the scene.

9. Resize each of the three boxes to cover the objects that you have placed in the scene.

10. Type the real-world height of the objects in the boxes in the lower-right corner of the screen.

11. Set the object width to complete the scene calibration.

C1316M-C (8/13) 41

Setting Object Width

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Click the profile that you want to use from the Select Profile list.

NOTE: You must repeat scene calibration for each profile you want to use.

4. Click the Calibrate Scene button.

5. Click the “Set width” button.

6. Click the Pause button to freeze the video while you make on-screen adjustments.

7. Using your mouse pointer, drag the two yellow lines on the screen to overlay an object that appears both in the foreground (near) and
background (far). For example, you might select a car, hallway, or street. Use the same type of object for both the near and far settings.

NOTES:

• Select an object that is larger horizontally to provide a more accurate perspective of the monitored scene.

• The monitored scene is more accurate when the “Width of near object” and the “Width of far object” lines are farther apart.

8. Resize both of the lines to exactly span the width of the objects that you are using for calibration.

9. Click the “Return to Main View” button to save your calibration settings and continue setting up analytics.

BEHAVIORS

Behaviors analyze objects within the camera’s field of view and are configured to detect and trigger alarms automatically when specific activity
is detected.

Examples of behaviors include Camera Sabotage, which detects contrast changes in the field of view and triggers an alarm if the lens is
obstructed or if the camera is repositioned; Adaptive Motion, which detects and tracks objects that enter a user-defined zone; and Object
Counting, which counts the number of objects that enter a defined zone.

Configuring a Behavior

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Select a profile from the Select Profile section.

4. Select the behavior for the profile from the Select Behaviors section.

5. Check the Activate Behavior box located in the “Settings for [behavior name]” section.

If the camera has enough resources, the behavior activates and a check mark appears to the left of the selected behavior(s), which is
located in the Select Behaviors section.

If the camera does not have enough resources, the following message and instructions appear: “The camera does not have enough
processing power to activate this behavior. To free up needed resources, turn off one of the other behaviors or reconfigure the video
streams.”

6. Set up the zones for the behavior.

7. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

42 C1316M-C (8/13)

ZONES

A zone is a defined boundary or area that is monitored by a configured behavior. A zone can be defined by a box, polygon, or line. If a box or
polygon is drawn to define the zone, any motion in the defined direction triggers an alarm. For example, if a line is drawn to define the zone, any
motion that crosses the line in the defined direction triggers an alarm. Objects within a zone can also be excluded and sized.

Drawing a Zone

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Click a behavior located in the Select Behaviors section.

4. Check the Activate Behavior box located in the “Settings for [behavior name]” section. A check mark appears to the left of the selected
behavior(s) located in the Select Behaviors section.

5. Use the draw tools to define the zone.

6. Set the behavior-specific settings for the zone.

7. To draw another zone, repeat steps 5 and 6.

8. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Deleting a Zone

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Click the behavior located in the Select Behaviors section that you want to modify.

4. The settings for the behavior are displayed in the “Settings for [behavior name]” section.

5. In the “Zone list” area of the page, click the check box next to the zone you want to delete.

6. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

Draw Zone Tools

NOTE: The available zone drawing tools depend on the configured analytic behavior.

Box: Tracks objects in a defined zone and triggers an alarm if the objects move in the same direction as defined.

Polygon: Tracks objects in a defined zone and triggers an alarm if the objects move in the same direction as defined.

Line: Tracks objects that cross a line and triggers an alarm if the objects move in the same direction as defined.

Exclude Zone Box Tool: Ignores objects inside a defined zone.

Exclude Zone Polygon Tool: Ignores objects inside a defined zone.

Object Size Filter: Sets the minimum and maximum object size for a zone.

C1316M-C (8/13) 43

ADAPTIVE MOTION

The Adaptive Motion behavior detects and tracks objects that enter a scene and then triggers an alarm when the objects enter a user-defined
zone. The objects are monitored until they exit the scene.

The Adaptive Motion behavior is designed to work indoors and outdoors to track a few moving objects in uncrowded fields of view. The behavior
learns the background scene over time and adjusts to changing conditions like snow, fog, wind, and rain.

Analytics events, including Adaptive Motion, are displayed on the live video page when viewing the Event stream. You must configure both an
analytics event source and the appropriate event handlers in order to receive notifications when an Adaptive Motion alarm is triggered.

Scene Setup for Adaptive Motion

Install the camera in a ceiling or against a wall with the lens pointing at a slight downward angle, above regular motion activity.

The ideal scene for Adaptive Motion behavior is one with light traffic and a clean background. If heavy traffic or a busy background is
unavoidable, place the user-defined zone in a relatively stable area.

Avoid crowded scenes where people move in all directions or stand in one place for long periods of time.

NOTE: Objects that are very small might not be classified as the correct object type. This could result in false alarms or alarms not being
triggered. If objects appear too small in the scene, move the camera closer to the zone of interest to increase the relative size of the objects in
the scene.

Selecting Adaptive Motion Settings

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Click the profile that you want to use from the Select Profile list.

4. Select Adaptive Motion from the Select Behaviors list.

5. Click the Activate Behavior check box to enable Adaptive Motion for the selected profile.

6. Use the zone draw tools to draw one or more zones of interest in the video pane.

7. After you have defined the desired zones, adjust the following zone settings:

Name: Assigns a descriptive name to make the zone easier to distinguish when viewing detection messages.

Direction: Detects and tracks moving objects and people that move in a specified direction within the defined zone.

Object type: Specifies which type of moving objects will be detected within the defined zone.

Enable alarm: Turns on the zone alarm, which displays a log of analytics events in the Event stream on the live video page. Alarms can

also trigger an event handler if sources and handlers are configured for analytics.

Alarm severity: Defines the severity of an alarm to allow the prioritization of alarms.

Dwell time: Defines the amount of time that an alarm remains activated after the alarm-triggering object exits the zone.

8. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

44 C1316M-C (8/13)

CAMERA SABOTAGE

The Camera Sabotage behavior detects contrast changes in the field of view. An alarm is triggered if the lens is obstructed by spray paint, a
cloth, or if it is covered with a lens cap. Any unauthorized repositioning of the camera also triggers an alarm.

Scene Setup for Camera Sabotage

Install the camera in a high position, looking down on the scene. The field of view should be as large as possible. A small field of view could
result in the view being blocked by an adjacent object.

Avoid scenes with a dark, uniform background; low lighting; and large moving objects.

Selecting Camera Sabotage Settings

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Click the profile that you want to use from the Select Profile list.

4. Select Camera Sabotage from the Select Behaviors list.

5. Click the Activate Behavior check box to enable Camera Sabotage for the selected profile.

6. Adjust the following zone settings:

Delay before alarm: Defines the delay between the time a violation is detected and the actual trigger of an alarm. If the violation does
not continue past the delay period, an alarm does not trigger. If the violation lasts longer than the delay period, an alarm triggers. The
default setting is 3 seconds.

Alarm severity: Defines the severity of an alarm to allow the prioritization of alarms.

7. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

C1316M-C (8/13) 45

LOITERING DETECTION

The Loitering Detection behavior identifies when people or vehicles remain in a defined zone longer than the user-defined time allows. This
behavior is effective in real-time notification of suspicious behavior around ATMs, stairwells, and school grounds.

Scene Setup for Loitering Detection

Install the camera in a ceiling or against a wall with the lens pointing at a slight downward angle, above regular motion activity.

The ideal scene for Loitering Detection behavior is one with light traffic and a clean background. If heavy traffic or a busy background is
unavoidable, place the user-defined zone in a relatively stable area.

Avoid crowded scenes where people move in all directions or stand in one place for long periods of time.

Selecting Loitering Detection Settings

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Click the profile that you want to use from the Select Profile list.

4. Select Loitering Detection from the Select Behaviors list.

5. Click the Activate Behavior check box to enable Loitering Detection for the selected profile.

6. Use the zone draw tools to draw one or more zones of interest in the video pane.

7. After you have defined the desired zones, adjust the following zone settings:

Name: Assigns a descriptive name to make the zone easier to distinguish when viewing detection messages.

Enable alarm: Turns on the zone alarm, which displays a log of analytics events in the Event stream on the live video page. Alarms can

also trigger an event handler if sources and handlers are configured for analytics.

Alarm severity: Defines the severity of an alarm to allow the prioritization of alarms.

Dwell time: Defines the amount of time that an alarm remains activated after the alarm-triggering object exits the zone.

Delay before alarm: Defines the amount of time an object must remain in the zone before an alarm triggers.

8. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

46 C1316M-C (8/13)

OBJECT COUNTING

The Object Counting behavior counts the number of objects that enter a user-defined zone. This behavior can be used to count people at a store
entrance/exit or inside a store where the traffic is light. It might also be used to monitor vehicle traffic on highways, local streets and roads,
parking lots, and garages.

Scene Setup for Object Counting

If you plan to detect people, install the camera pointing downward (vertically) above regular motion activity. If you plan to detect vehicles, install
the camera pointing downward at a slight angle above regular motion activity.

The ideal scene selection for the Object Counting behavior is one with light traffic, minimal object obstructions, and a clean background. If heavy
traffic or a busy background is unavoidable, place the monitoring zone (polygon or line) in a relatively stable area.

A one-directional motion scene (for example, a vertical hallway) is preferable. Avoid crowded scenes where people move in all directions or
remain in one place for long periods of time.

Selecting Object Counting Settings

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Click the profile that you want to use from the Select Profile list.

4. Select Object Counting from the Select Behaviors list.

5. Click the Activate Behavior check box to enable Object Counting for the selected profile.

6. Use the zone draw tools to draw one or more zones of interest in the video pane.

7. After you have defined the desired zones, adjust the following zone settings:

Name: Assigns a descriptive name to make the zone easier to distinguish when viewing detection messages.

Direction: Detects and tracks moving objects and people that move in a specified direction within the defined zone.

Object type: Specifies which type of moving objects will be detected within the defined zone.

Enable alarm: Turns on the zone alarm, which displays a log of analytics events in the Event stream on the live video page. Alarms can

also trigger an event handler if sources and handlers are configured for analytics.

Alarm severity: Defines the severity of an alarm to allow the prioritization of alarms.

Dwell time: Defines the amount of time that an alarm remains activated after the alarm-triggering object exits the zone.

8. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

C1316M-C (8/13) 47

STOPPED VEHICLE

The Stopped Vehicle behavior detects vehicles stopped near a sensitive area longer than the user-defined time allows. This behavior is ideal for
parking enforcement, suspicious parking, traffic lane breakdowns, and vehicles waiting at gates.

Scene Setup for Stopped Vehicle

Install the camera in a ceiling or against a wall with the lens pointing at a slight downward angle, above regular motion activities.

The ideal scene selection for Stopped Vehicle behavior is one with light traffic where vehicles are continually moving, minimal object
obstruction, and a clean background. If heavy traffic or a busy background is unavoidable, place the monitoring zone in a relatively stable area.

Avoid crowded scenes where people or objects remain in one place for long periods of time.

Selecting Stopped Vehicle Settings

1. Place your mouse pointer over the Events tab.

2. Select Analytic Configuration from the drop-down menu.

3. Click the profile that you want to use from the Select Profile list.

4. Select Stopped Vehicle from the Select Behaviors list.

5. Click the Activate Behavior check box to enable Stopped Vehicle for the selected profile.

6. Use the zone draw tools to draw one or more zones of interest in the video pane.

7. After you have defined the desired zones, adjust the following zone settings:

Name: Assigns a descriptive name to make the zone easier to distinguish when viewing detection messages.

Enable alarm: Turns on the zone alarm, which displays a log of analytics events in the Event stream on the live video page. Alarms can

also trigger an event handler if sources and handlers are configured for analytics.

Alarm severity: Defines the severity of an alarm to allow the prioritization of alarms.

Dwell time: Defines the amount of time that an alarm remains activated after the alarm-triggering object exits the zone.

Delay before alarm: Defines the amount of time an object must remain in the zone before an alarm triggers.

8. Click the “Enable advanced options” box to adjust the following additional setting:

Sensitivity: Overrides the global Profile sensitivity setting. Defines the motion detection sensitivity, which includes minimum motion
sensitivity and minimum motion size. The default setting is 5; settings range from 1 (low) to 10 (high).

NOTE: When advanced options are enabled with the Stopped Vehicle behavior, any excluded zones that you have previously created
within the scene are disabled. Additional excluded zones can be created, but they will remain exclusive to this behavior within the selected
profile.

9. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.

48 C1316M-C (8/13)

Specifications

THERMAL CAMERA/OPTICS

Detector Sun-safe, uncooled microbolometer, amorphous silicon

Array Format 640 x 480, 384 x 288, or 240 x 184

Pixel Size

640 x 480 17 µm
384 x 288, 240 x 184 25 µm

Effective Resolution 307,200 (640 x 480); 110,592 (384 x 288); 44,160 (240 x 184)

Spectral Response 7.5 to 13.5 µm, LWIR

Normalization Source Internal shutter (offset only), 0.3 second video freeze during shutter

Temporal NETD 50 mK at f/1.0

Display Formats White hot, black hot, and rainbow

LENS

Lens (mm) F-Number (f)

14.25 1.2 44° x 33° x 54°

35 1.4 18° x 13° x 22°

50 1.2 12° x 9° x 15°

100 1.4 6° x 5° x 8°

14.25 1.2 39° x 29° x 48°

35 1.4 16° x 12° x 19°

50 1.7 11° x 8° x 14°

100 1.6 6° x 4° x 7°

6.30 1.2 55° x 41° x 68°

640 x 480 Resolution

Field of View

(H/V/D)

384 x 288 Resolution

240 x 184 Resolution

VIDEO

IP/Network

Video Encoding H.264 High, Main, or Base profiles; MJPEG, and JPEG.

Video Streams Up to 2 simultaneous streams; the second stream is variable based on the setup of the primary stream

Frame Rate* Up to 30, 25, 24, 15, 12.5, 12, 10, 8, 7.5, 6, 5, 4, 3, 2.5, 2, 1 (dependent upon stream configuration)

Available Resolutions 640 x 480, 384 x 288, and 240 x 184

Supported Protocols TCP/IP, UDP/IP (Unicast, Multicast IGMP), UPnP, DNS, DHCP, RTP, RTSP, NTP, IPv4, IPv6†, SNMP, QoS,

HTTP, HTTPS, LDAP (client), SSH, SSL, SMTP, FTP, and 802.1x (EAP)

Users

Unicast Up to 20 simultaneous users depending on resolution settings (2 guaranteed streams)
Multicast Unlimited users H.264

Security Access Password protected

Software Interface Web browser view and setup

Pelco System Integration Endura 2.0 (or later) Digital Sentry

Analog

Video 75 ohms, unbalanced

Video Modes NTSC or PAL

Video Level 1 Vp-p

*Some models are limited to 8.33 ips to comply with US government export control regulations.

†

Supports mixed IPv4 and IPv6 envornments, but not IPv6-only deployments.

®

4.2 (or later)

C1316M-C (8/13) 49

ELECTRICAL

Port RJ-45 connector for 100Base-TX, auto MDI/MDI-X

Cabling Type Cat5 or better for 100Base-TX

Power Input 24 VAC or 24 VDC

Input Voltage Range +15%, -20%

Power Consumption Lens (mm) Power

24 VAC 6.30, 14.25, 30, 50; 1.30 A, 30 VA (22 W);

100 3.8 A, 90 VA (82 W)

24 VDC 6.30, 14.25, 30, 50; 0.90 A (22 W);

100 3.50 A (85 W)

Local Storage Micro SD

Alarm Input N.O. switch, N.C. switch, or 1 kohm; supervised

Alarm Output 0 to 32 VDC maximum, 100 mA maximum

Audio Bidirectional, half duplex; Line level/external microphone input; 600 Ohm differential;

1 Vp-p max signal level

Compression G.711 PCM 64 kbps

MECHANICAL

Cable Access Cover 2 captive Torx™ screws

Cable Entry 2 adjustable 0.5-inch NPT liquid-tight glands

GENERAL

Construction Aluminum

Finish Gray polyester powder coat

Environment Indoor/outdoor

Operating Temperature –40° to 50°C (–40° to 122°F)

Storage Temperature –40° to 60°C (–40° to 140°F)

Weight

14.25 mm 3.1 kg (6.9 lb)
35 mm 3.2 kg (7.2 lb)
50 mm 3.3 kg (7.3 lb)
100 mm 3.4 kg (7.5 lb)

NOTE: VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS.

5.08

(2.00)

37.59

(14.80)

33.78

(13.30)

12.57
(4.95)

12.77
(5.03)

2.54

(1.00)

50 C1316M-C (8/13)

WARRANTY STATEMENT

For information about Pelco’s product warranty and thereto related information, refer to www.pelco.com/warranty.

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

REVISION HISTORY

Manual # Date Comments

C1316M 8/11 Original version.
C1316M-A 8/12 Updated to include 1.8.2 changes and 240 x 184 resolution.
C1316M-B 10/12 Updated to correct F-numbers for 640 x 480 cameras.
C1317M-C 8/13 Updated to include Sarix 1.9.2 features.

Pelco, the Pelco logo, and other trademarks associa ted with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affilia tes. © Copyright 2013, Pelco, Inc.
ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies. All rights reserved.
Product specifications and availability are subject to change without notice.

Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612-5699 United States

USA & Canada Tel [phone] Fax [phone]

International Tel [phone] Fax [phone]

www.pelco.com www.pelco.com/community