®
Installation/Operation
CC3500/CC3600 Series
Color Cameras
C1981M-C (8/02)
Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com
USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150
International: Tel: 1-559/292-1981 • Fax: 1-559/348-1120
[ 2 ] Pelco Manual C1981M-C (8/02)
CONTENTS
IMPORTANT SAFEGUARDS AND WARNINGS ................................................................................. 4
Regulatory Notices ............................................................................................................................... 5
DESCRIPTION .................................................................................................................................... 5
Models ................................................................................................................................................. 5
CAMERA LAYOUT ............................................................................................................................... 6
INSTALLATION .................................................................................................................................... 6
Lens Mounting ..................................................................................................................................... 6
Camera Mounting ................................................................................................................................ 7
POWER AND VIDEO CONNECTIONS ............................................................................................... 8
POWER CONNECTIONS .................................................................................................................... 8
LENS SETUP AND FOCUS PROCEDURES .................................................................................... 10
BACK FOCUS ADJUSTMENT...........................................................................................................11
SWITCH SETTINGS .......................................................................................................................... 12
CAMERA SYNCHRONIZATION ........................................................................................................ 14
SPECIFICATIONS ............................................................................................................................. 15
WARRANTY AND RETURN INFORMATION .................................................................................... 16
LIST OF ILLUSTRATIONS
Figure 1. Camera Layout .................................................................................................................... 6
Figure 2. DD/AI Lens Connector ......................................................................................................... 7
Figure 3. Camera Mounting ................................................................................................................ 7
Figure 4. Power Supply Connections .................................................................................................. 8
Figure 5. AGC and EI Switch Settings .............................................................................................. 10
Figure 6. Back Focus Adjustment ..................................................................................................... 11
Figure 7. Switch Settings .................................................................................................................. 12
LIST OF TABLES
Table A. Recommended Wire Gauge and Wiring Distances............................................................... 9
Table B. Video Coaxial Cable Requirements ......................................................................................9
Pelco Manual C1981M-C (8/02) [ 3 ]
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Only use attachments/accessories specified by the manufacturer.
10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, the apparatus does not operate normally, or the apparatus has been dropped.
12. Apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
13. Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture.
14. Caution: Danger of explosion if battery is replaced incorrectly. Replace only with the same or
equivalent type.
15. To reduce the risk of shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
16. Use only installation methods and materials capable of supporting four times the maximum
specified load.
17. Use only UL listed class 2 power supply.
18. DD/AI Lens Connector
The maximum load for a direct drive lens must not exceed 25 mA.
The maximum load for an auto-iris lens must not exceed 50 mA.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
This symbol indicates that there are important operating and maintenance instructions
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
in the literature accompanying this unit.
Please thoroughly familiarize yourself with the information in this manual prior to installation and
operation.
[ 4 ] Pelco Manual C1981M-C (8/02)
REGULATORY NOTICES
This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device many not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
DESCRIPTION
The CC3500 and CC3600 Series are compact, color video cameras with a 1/3-inch CCD imager.
All cameras have a direct drive/auto iris lens connector and adjustable back focus, and they accept
C and CS lenses.
Models
CC3500S-2 Standard resolution, 330 TV lines, HyperHAD™ CCD, 1.0 lux at f1.2, NTSC
CC3500H-2 High resolution, 480 TV lines, HyperHAD CCD, 1.0 lux at f1.2, NTSC
CC3600H-2 High resolution, 480 TV lines, EXview HAD CCD™, 0.6 lux at f1.2, NTSC
CC3500S-2X Standard resolution, 330 TV lines, HyperHAD CCD, 1.0 lux at f1.2, CCIR
CC3500H-2X High resolution, 480 TV lines, HyperHAD CCD, 1.0 lux at f1.2, CCIR
CC3600H-2X High resolution, 480 TV lines, EXview HAD CCD+, 0.6 lux at f1.2, CCIR
Pelco Manual C1981M-C (8/02) [ 5 ]
CAMERA LAYOUT
BACK FOCUS
ADJUSTMENT
LOCKING
SCREW
BACK FOCUS
ADJUSTMENT
RING
MOUNT ADAPTER
PHASE ADJUSTMENT
LEVEL ADJUSTMENT
POWER SUPPLY
COSMETIC TRIM
RING
BNC VIDEO CONNECTOR
LENS CONNECTOR
LED
DIP SWITCHES
Figure 1. Camera Layout
NOTE: The cosmetic trim ring conceals the LED light for more discreet surveillance operations.
The trim ring also hides the power connectors and protects the DIP switches.
INSTALLATION
Lens Mounting
The CC3500 and CC3600 Series cameras can use fixed iris, manual iris, auto iris, or direct drive
lenses. Cameras are factory-set for CS-mount lenses, but easily adjusted for C-mount lenses.
1. C-Mount Lens Only - Loosen the two back focus locking screws. Rotate the back focus
adjustment ring fully counterclockwise before installing the C-mount lens (refer to the section on
Back Focus Adjustment
2. Remove the cosmetic trim ring from the back of the camera (refer to Figure 1). Set the lens mode
selector switch on the side of the camera to AI (auto iris video drive lens) or DD (auto iris DC
drive lens). Refer to the Switch Settings section. Switch setting is determined by the type of lens
used.
3. Screw the lens onto the lens mount. Be careful to prevent dust from entering the space between the
lens and the CCD element. If necessary, use clean, compressed air to remove any foreign matter.
4. Thread the lens cable through the cosmetic trim ring.
5. Connect the direct drive (DD) or auto iris (AI) lens to the 4-pin iris drive connector located on the
side of the camera. Pin connections for the iris drive connector are as follows.
).
[ 6 ] Pelco Manual C1981M-C (8/02)
3 4
12
PIN DD LENS CONNECTIONS AI LENS CONNECTIONS
1 Control coil negative (-) Not used
2 Control coil positive (+) Lens positive supply
3 Drive coil positive (+) Video drive signal
4 Drive coil negative (-) Ground
Figure 2. DD/AI Lens Connector
Camera Mounting
Use a standard 1/4-20 screw (provided) with a maximum thread length of 3/8-inch (10 mm) for top or
bottom camera mounting. The mount adapter may be fitted to the top or bottom of the camera. The
camera is shipped with the mount adapter located on the top of the camera.
To change the mount adapter position:
1 Remove the four screws from the mount adapter located on the top of the camera.
2 Remove the trim cover from the bottom of the camera by prying it loose. Place the trim cover on
the top of the camera where the mount adapter was removed. Press into place.
3 Install the mount adapter to the bottom of the camera. Secure with the four screws removed in
step 1.
1
2
3
Figure 3. Camera Mounting
Pelco Manual C1981M-C (8/02) [ 7 ]
POWER AND VIDEO CONNECTIONS
To connect the camera power and video do the following:
1. Remove the rear cover from the camera (refer to Figure 1). Thread cabling through the rear cover.
2. Connect the power cable to the two pin power connector on the back of the camera using the
terminal block connector provided. Refer to Table A for the recommend wire gauge to use for
the installation.
3. Connect a video cable to the SIGNAL OUT connector (BNC) on the back of the camera. Refer to
Table B for the type of video coaxial cable to use.
4. Reattach the rear cover to the back of the camera.
Power Connections
CC3500 and CC3600 Series cameras are designed to operate from a 12 VDC or 24 VAC power supply. The power supply connections are shown in Figure 4. The LED on the back panel of the camera
indicates that power is connected. Use only a Class 2 isolated power supply. Power consumption is
less than 5 watts.
CLASS 2
ISOLATED
POWER
SUPPLY
24 VAC 12 VDC
CLASS 2
ISOLATED
POWER
SUPPLY
Figure 4. Power Supply Connections
To connect the camera power and video:
1. Remove the cosmetic trim ring from the camera (refer to Figure 1). Thread cabling through the
rear cover.
2. Connect the power cable to the two pin power connector on the back of the camera using the
terminal block connector (provided). Refer to Table A for the recommend wire gauge and wiring
distances.
3. Connect a video cable to the SIGNAL OUT connector (BNC) on the back of the camera. Refer to
Table B for the type of video coaxial cable to use.
4. Reattach the trim ring to the back of the camera.
[ 8 ] Pelco Manual C1981M-C (8/02)
AC Operation Only – If you are wiring more than one camera to the same transformer, connect one
side of the transformer to the same terminal on all cameras, and connect the other side of the transformer to the remaining terminal on all cameras. Failure to connect all of the cameras the same way
will cause the cameras to be out of phase with each other and may produce a vertical roll when
switching between cameras.
Table A. Recommended Wire Gauge and Wiring Distances
The following are the recommended maximum distances for 24 VAC applications and are calculated
with a 10-percent voltage drop. (Ten percent is generally the maximum allowable voltage drop for
AC-powered devices.)
Wire Gauge
Total 20 18 16 14 12 10
vA (0.5 mm2) (1.0 mm2) (1.5 mm2) (2.5 mm2) (4.0 mm2) (6.0 mm2)
10 283 451 716 1142 1811 2880
(86) (137) (218) (348) (551) (877)
EXAMPLE: A camera that requires 10 vA and is installed 283 feet (86 m) from the transformer
would require a minimum wire gauge of 20 AWG.
NOTE: Distances are calculated in feet; values in parentheses are meters.
Table B. Video Coaxial Cable Requirements
Cable Type* Maximum Distance
RG59/U 750 ft (229 m)
RG6/U 1,000 ft (305 m)
RG11/U 1,500 ft (457 m)
* Minimum cable requirements:
75 ohms impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage
Pelco Manual C1981M-C (8/02) [ 9 ]
LENS SETUP AND FOCUS PROCEDURES
Video Drive Auto Iris Lens
When a video drive auto iris lens is used, the lens mode selector switch must be set to AI. Switch the
EI and AGC OFF. Refer to the lens instructions and adjust the lens for the optimum picture (video
output level of 1V peak-to-peak). Switch the AGC ON. To focus, fully open the iris by covering the
lens with a suitable neutral density (ND*) filter. If the viewed scene is 6.5 feet (2 m) away or farther,
set the lens focus to infinity (far). Use the back focus adjustment ring (refer to the
ment
section) and focus on the selected scene. Remove the ND filter and set the lens focus as re-
quired.
Direct Drive (DC) Auto Iris Lens
When a direct drive lens is used, the lens mode selector switch must be set to DD. Switch the EI and
AGC OFF. Use an appropriate screwdriver to turn the lens level potentiometer (refer to Figure 1)
fully clockwise. Next, slowly adjust the potentiometer counterclockwise until the optimum picture is
obtained (video output level of 1V peak-to-peak). Switch the AGC ON. To focus, fully open the iris by
covering the lens with a suitable neutral density (ND*) filter. Select the scene to be viewed. If the
viewed scene is 6.5 feet (2 m) away or farther, set the lens focus to infinity (far). Use the back
focus adjustment ring (refer to the
Back Focus Adjustment
section) and focus on the selected scene.
Remove the ND filter and set the lens focus as required.
Fixed Lens
Set the EI switch and AGC switch to ON. To focus, set the lens focus to infinity and view an image
greater than 6.5 feet (2 m) away. Focus the image with the back focus adjustment ring (refer to the
Back Focus Adjustment
section). Set the lens focus as required.
Manual Iris Lens
Set the EI switch and AGC switch to ON. To focus, open the iris fully and set the lens focus to infinity.
View an image greater than 6.5 feet (2 m) away. Focus the image with the back focus adjustment ring
(refer to the
Back Focus Adjustment
section). Adjust the lens focus and set the iris for the best picture
quality. The largest aperture gives the best light sensitivity, the smallest aperture the greatest depth of field.
Back Focus Adjust-
Zoom Lens
Set the lens focus to infinity (far) and fully open the iris by covering the lens with a suitable neutral
density (ND*) filter. Zoom out to the widest field of vision and view a distant object. Adjust the back
focus adjustment ring until the object is in focus (refer to the
Back Focus Adjustment
section).
Next, zoom fully in and adjust the lens focus until the object is again focused. Repeat these steps
until the full zoom range may be viewed with the minimum loss of focus.
4
3
7
7
AGC ON
AGC OFF
EI ON
1
4
EI OFF
3
DIP SWITCH SETTINGS – WHITE REPRESENTS SWITCH POSITION
Figure 5. AGC and EI Switch Settings
*NOTE: For best results outdoors use an ND3 filter.
[ 10 ] Pelco Manual C1981M-C (8/02)
BACK FOCUS ADJUSTMENT
The back focus adjustment is located at the front of the camera and is accessible from either side of
the case.
To adjust the back focus:
1. Loosen the two back focus locking screws (one on each side).
2. Turn the back focus ring:
a. Clockwise - Moves the CCD sensor assembly towards the back of the lens.
b. Counterclockwise - Moves the CCD sensor away from the lens.
3. When the back focus adjustment is satisfactory, tighten the locking screws. Do not over-turn or
force the back focus adjustment ring.
COUNTERCLOCKWISE
BACK FOCUS
ADJUSTMENT
BACK FOCUS
ADJUSTMENT
RING
CLOCKWISE
Figure 6. Back Focus Adjustment
LOCKING SCREW
Pelco Manual C1981M-C (8/02) [ 11 ]
SWITCH SETTINGS
8
8
NORMAL (0.45)
LINEAR (1.0)
BLACK REPRESENTS
SWITCH POSITION
10
9
8
7
6
5
4
3
2
1
Figure 7. Switch Settings
Color Balance - Switch Settings 9 and 10
Pelco’s CC3500 and CC3600 cameras have four color balance settings.
Auto (Default setting) - Automatically corrects the color balance of
the picture.
6300°K - May improve the color balance in areas where 6300°K
lighting is the main source.
3200°K - May improve the color balance in some indoor lighting
conditions.
4200°K - May improve some indoor fluorescent lighted scenes.
Gamma - Switch Setting 8
Set the Gamma level to one of the following:
Normal (Default setting) - Increases visibility in dark areas of the
picture.
Linear - Linear response increases (overall) contrast.
AGC (Automatic Gain Control) - Switch Setting 7
Automatically adjusts the image to compensate for changes in light levels
when using fixed or manual iris lenses. Following are the AGC switch
settings:
ON (Default setting) - Enables the AGC mode.
OFF - Disables the AGC mode.
Lens Mode Selector (AI/DD Switch) - Switch Setting 6
The AI/DD switch setting is determined by the type of lens used:
AI - Auto iris lens
DD - Direct drive lens
SYNC (Synchronization) - Switch Setting 5
Locks the frame rate to the power supply frequency. Eliminates vertical roll
caused by multiple cameras connected to the same switching device. Each
camera output is synchronized to the frequency of the power supply. Set the
camera synchronization mode to one of the following:
Line Lock (LL) - Line-locks frame rate of cameras.
Internal - Disables line lock.
01236
10
9
10
9
10
9
10
9
7
7
6
6
5
5
AUTO
6300OK
3200OK
4200OK
AGC ON
AGC OFF
AI LENS
DD LENS
LL
INTERNAL
[ 12 ] Pelco Manual C1981M-C (8/02)
Shutter Speed Selection - Switch Settings 4, 3, 2, and 1
4
3
1/50
2
1
4
3
1/125
2
1
4
3
1/250
2
1
4
3
1/500
2
1
4
3
1/1,000
2
1
4
3
1/2,000
2
1
4
3
2
1
4
3
2
1
EI (Electronic Iris) Switch Settings 4, 3, and 1
The EI (Electronic Iris) feature compensates for an excessive light level by
automatically adjusting shutter speed. Selecting Electronic Iris disables
manual shutter speed selection. The Electronic Iris setting must not be used
when the camera is set to Flickerless mode. Following are the EI switch
settings:
ON (Default setting) - Enables the Electronic Iris mode.
OFF - Disables the Electric Iris mode.
BLC (Backlight Compensation) Switch Settings 2 and 4
The BLC (Backlight Compensation) feature compensates for backlit scenes
by enhancing objects in the center of the scene that would previously have
been in silhouette. BLC will only function with a manual iris lens when the
Electronic Iris feature is switched on. For direct drive and auto iris lenses,
BLC will still function even though the Electronic Iris feature is switched off.
Following are the EI switch settings:
ON - Enables the BLC mode.
OFF (Default setting) - Disables the BLC mode.
Flickerless Switch Settings 4, 3, and 1
The Flickerless setting can reduce the flicker caused by certain lighting conditions. The Electronic Iris setting must be off for correct operation of the
Flickerless function. Choose between the following settings:
ON - Enables the Flickerless mode.
OFF (Default setting) - Disables the Flickerless mode.
1/4,000
1/10,000
00014
4
3
1
4
3
4
2
4
2
4
3
1
4
1
EI ON
EI OFF
BLC ON
BLC OFF
FLICKERLESS
ON
FLICKERLESS
OFF
Pelco Manual C1981M-C (8/02) [ 13 ]
CAMERA SYNCHRONIZATION
When using one AC power supply in a multi camera system, a brief vertical roll may occur on the
monitor each time a camera view is switched. To eliminate vertical roll adjust the phase control to
synchronize (line-lock), the cameras to one another. The synchronization switch (DIP switch 5)
for each camera must be set to LL. Use the potentiometer located on the side of the camera to
make adjustments
It may be necessary to have two people in communication when synchronizing the cameras: one
person at the camera and another person at the monitor to observe the vertical roll and the effect of
any adjustments made at the camera.
To synchronize the cameras do the following:
1. Choose a reference camera to which all other cameras will be phased.
2. Select a camera and synchronize it to the reference camera by turning the phase adjustment
control clockwise and/or counterclockwise.
3. Each time an adjustment is made, switch back and forth between the camera you are adjusting
and the reference camera. Repeat this process as many times as necessary, until the roll
between the cameras is no longer noticeable.
4. Adjust the phase of all other cameras by repeating steps 2 through 3. Always adjust to the
reference camera selected in step 1.
NOTE: The preferred method for camera phase adjustment is to use a dual trace oscilloscope to
align the vertical sync pulses of the reference camera to the selected camera(s).
[ 14 ] Pelco Manual C1981M-C (8/02)
SPECIFICATIONS
GENERAL
CCD Sensor: 1/3-inch
Picture Elements
CC3500S-2: 510 (H) x 492 (V)
CC3500H-2: 768 (H) x 494 (V)
CC3600H-2: 768 (H) x 494 (V)
Sensing Area: 6mm diagonal
Synchronization System: AC line lock or internal oscillator
Horizontal Resolution
CC3500S-2, CC3500S-2X: 330 TV lines
CC3500H-2, CC3500H-2X: 480 TV Lines
CC3600H-2, CC3600H-2X: 480 TV Lines
Iris Control: Electronic/passive
Minimum Illumination
CC3500S-2, CC3500S-2X: 1.0 lux at f1.2
CC3500H-2, CC3500H-2X: 1.0 lux at f1.2
CC3600H-2, CC3600H-2X: 0.6 lux at f1.2
Signal-to-Noise Ratio: 52 dB (AGC Off)
Gain Control: Automatic
Vertical Phase: Adjustable 0° ±120°
Automatic Gain Control: Selectable by DIP switch setting
Backlight Compensation: Selectable by DIP switch setting
Scanning System: 525 lines, 2:1 interlace
Signal Processing: DSP
Auto Iris Lens Type: DC/video control
Video Output: 1 Vp-p, 75 ohms
Iris Control Range: 1/60-1/100,000 second
Auto White Balance Range: 2500-9500 K
ELECTRICAL
Power Requirements: 11-40 VDC or 14-30 VAC
Power Connector: 2-pin terminal strip, push-in type
Video Connector: BNC
Lens Jack: 4-pin connector (miniature square)
Power Consumption: Less than 6.5 watts
MECHANICAL
Lens Mount: C/CS mount (adjustable)
Camera Mount: Use 1/4-20 screw, top or bottom of camera housing
ENVIRONMENTAL
Operating Temperature: 14° to 122°F (-10° to 50°C)
Storage Temperature: 14° to 158°F (-10° to 70°C)
PHYSICAL
Dimensions: 2.48 (W) x 2.67 (H) x 4.33 (D) inches (6.3 x 6.8 x 11 cm)
Weight (without lens): 0.77 lb (0.35 kg)
(Design and product specifications subject to change without notice.)
Pelco Manual C1981M-C (8/02) [ 15 ]
WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after
the date of shipment. Exceptions to this warranty are as noted below:
• Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600 Series); two years on all other cameras.
• Three years on Genex® Series (multiplexers, server, and keyboard) and 090 Series Camclosure® Camera System.
•Two years on 100/150, 200 and 300 Series Camclosure
•Two years on all standard motorized or fixed focal length lenses.
•Two years on Legacy
•Two years on Spectra
•Two years on Esprit and WW5700 series window wiper (excluding wiper blades).
• Eighteen months on DX Series digital video recorders.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto
scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall
be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are
not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the
Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or
product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be
liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however
caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation
from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization
number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a
written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an
authorization number (CA number if returned for credit, and RA number if returned for repair). Goods returned for repair or credit should be
clearly identified with the assigned CA/RA number and freight should be prepaid. All merchandise returned for credit may be subject to a
20% restocking and refurbishing charge.
Ship freight prepaid to: Pelco
® Pelco, the Pelco logo, Spectra, Genex, Legacy, PelcoVision, Esprit, and Camclosure are registered trademarks of Pelco.
®
, CM6700/CM6800/CM8500/CM9500/CM9740/CM9760 Matrix, DF5 and DF8 Series Fixed Dome products.
®
, Esprit®, and PS20 Scanners, including when used in continuous motion applications.
3500 Pelco Way
Clovis, CA 93612-5699
™ HyperHAD and EXview HAD CCD are trademarks of the Sony Corporation.
®
Camera Systems.
© Copyright 2002, Pelco. All rights reserved.
REVISION HISTORY
Manual # Date Comments
C1981M 6/00 Original version.
10/00 Revised Lens Setup and Focus Procedures.
C1981M-A 12/00 Revised switch settings.
C1981M-B 7/01 Revised Warranty and Return Information.
C1981M-C 8/02 Added Canadian UL certification. Revised
Important Safeguards and Warnings.
Loading...