Pelco C986M-A User Manual

®

RMA14

Rack Mount Kit

Installation/Operation Manual

Manual C986M-A (5/95)

1.0 WARNINGS

Prior to installation and use of this product, the following
WARNINGS should be observed.

1. Installation and servicing should only be done by
Qualified Service and Installation Personnel.

2. Installation shall be done in accordance with all
local and national electrical and mechanical codes
utilizing only approved materials.

3. Use only installation methods and materials capable
of supporting four (4) times the maximum specified
load.

2.0 SCOPE

The information within this manual covers the installa­tion of the RMA14 Rack Mount Kit.

Installation should be in accordance with all applicable
local and national electric codes, utilizing approved
materials only.

Please thoroughly familiarize yourself with the infor­mation in this manual prior to installation and operation.

3.0 DESCRIPTION

The RMA14 Rack Mount Kit is designed to provide
rack mounting for single PELCO PMC14 or PMC 14­X monitors.

This versatile rack will fit any standard 19 inch wide
console or rack configuration.

PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • [phone] or (1-559) 292-1981

FAX [phone] or (1-559) 292-3827

4.0 SPECIFICATIONS

Dimensions: See Figure 1
Construction: 16-gauge steel
Weight: 8 lbs 12 oz.

5.0 INSTALLATION

The RM14 rack kit is supplied unassembled. The fol­lowing hardware is provided for use in assembling the
rack kit.

Qty Description

6 10/32 Hex nuts
6 #10 Lock washers

1. Assemble the rack as shown in Figure 2 using the
supplied hardware.

While assembling, install all hardware loosely un­til all components are attached and then finish by
tightening all hardware.

2. Set the monitor into the rack, aligning the four (4)
feet with the holes in the base plate.

3. Install rack and monitor as an assembly into con­sole and make any required electrical connections.

4. Hold into place, aligning mounting holes of the
RMA14 with mounting holes in console, and insert
and tighten required fasteners (not supplied).

To install the rack kit and monitor, perform the follow­ing steps:

A faceplate is supplied if required.

Figure 1. RMA14 Dimension Drawing

2 PELCO Manual C986M-A (5/95)

Figure 2. RMA14 Rack Kit Assembly

PELCO Manual C986M-A (5/95) 3

6.0 WARRANTY AND RETURN
INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved
defective in material or workmanship for a period of one year after the date
of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series fiber optic products.

• Three years on Genex

keyboard).

• Three years on Camclosure

CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.

• Two years on standard motorized or fixed focal length lenses.

• Two years on Legacy

DF5/DF8 Series fixed dome products.

• Two years on Spectra

ing when used in continuous motion applications.

• Two years on Esprit

wiper blades).

• Eighteen months on DX Series digital video recorders, NVR300

Series network video recorders, and Endura
network-based video products.

• One year (except video heads) on video cassette recorders (VCRs).

Video heads will be covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in

continuous motion applications (that is, preset scan, tour and auto scan
modes).

Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289­9100 or [phone] to obtain a Repair Authorization number (RA),
and provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice

number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall
under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.

®

Series products (multiplexers, server, and

®

and fixed camera models, except the

®

, CM6700/CM6800/CM9700 Series matrix, and

®

, Esprit®, ExSite™, and PS20 scanners, includ-

®

and WW5700 Series window wiper (excluding

™

Series distributed

RETURNS

In order to expedite parts returned to the factory for repair or credit, please
call the factory at [phone] or [phone] to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:

If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:

Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699

Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA

Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: [phone]
Fax: [phone]

®

PELCO

300 West Pontiac Way

Clovis, CA 93612-5699 USA

[phone] • [phone]

FAX [phone] or [phone]

International customers call 1-559-292-1981 or

FAX [phone]

Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.

© Copyright 1995, Pelco. All rights reserved.

(Product specifications subject to change

without notice.)

C986M-A

4 PELCO Manual C986M-A (5/95)