Peerless-AV SA761P Installation [en, es, fr]

Installation and Assembly: PeerCare™ Universal

Articulating Arm Wall Mount for 37" to 71" Flat Panel Displays

Models: SA771PU-AB, SA771PU-AW

Features:

• Treated with Agion® medical antimicrobial ﬁ nish in black or white designed to assist with infection control

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

Max UL Load Capacity: 200 lb (90.7 kg)

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

Note: Read entire instruction sheet before you start installation and assembly.

WARNING

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum UL Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁ nder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁ rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

• Wood Beam Included

• Solid Concrete Included

• Cinder Block Included

• Metal Stud Contact Qualiﬁ ed Professional (not evaluated by UL)

• Brick Contact Qualiﬁ ed Professional (not evaluated by UL)

• Other or unsure? Contact Qualiﬁ ed Professional

Tools Needed for Assembly

• stud ﬁ nder ("edge to edge" stud ﬁ nder is recommended)

• phillips screwdriver

• drill

• 3/16" (5mm) drill bit for wood studs, 3/8" (10mm) drill bit for concrete

• level

Table of Contents

Parts List.............................................................................................................................................................................3, 4

Wall installation ...................................................................................................................................................................6, 7

Installing Adapter Brackets to Screen................................................................................................................................8-13

Mounting Flat Panel Screen .................................................................................................................................................14

Cable Management ..............................................................................................................................................................16

2 of 56

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

Before you begin, make sure all parts shown are included with your product.

Parts List

Description Qty. Part # Part #

wall arm assembly 1 095-S1994 095-S2994

B universal adapter bracket 1 095-S1635-1 095-S2635-1 C wood screws 4 520-1243 520-2243 D concrete anchors 4 590-0321 590-0321

M10 x 15 mm socket head screw

wall plate cover

cable ties

G H 6 mm allen wrench 1 560-9716 560-9716

I 5 mm allen wrench 1 560-9640 560-9640 J rear cable cover 4 590-P1326 590-2326 K front cable cover 4 590-P1327 590-2327 L Panasonic extension bracket 2 095-S1623 095-S2623 M Sharp extension bracket 2 095-S1622 095-S2622 N 1/4-20 self tapping screws 4 520-1633 520-2633 O M10 x 15 phillips screws 4 520-1305 520-2305

5/32" allen wrench 1 560-9646 560-9646

Parts may appear slightly different than illustrated.

SA771PU-ABSA771PU-A

520-9262 520-9534

590-1325 590-2325

590-1168 590-1168

HIP

3 of 56

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

Adapter Bracket Fasteners

M4 x 12mm (6)

(504-9013)

M6 x 30mm (4)

(510-9109)

M4 x 25mm (4)

(504-1015)

M8 x 16mm (6)

(520-9257)

M5 x 12mm (4)

(520-1027)

M8 x 25mm (4)

(520-1031)

M5 x 25mm (4)

(520-9543)

M8 x 40mm (4)

(520-1136)

M6 x 12mm (4)

(520-1128)

I.D. .22" (4)

(540-1057)

I.D. .34" (4)

(540-1059)

M6 x 20mm (4)

(520-9402)

multi-washer (6)

M6 x 25mm (4)

(520-1208)

(580-1036)

4 of 56

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

Optional Horizontal Adjustment of Wall Arm on Wall Plate

NOTE: If mounting wall arm (A) to wood stud walls, slots on wall plate must align to wood studs.

Determine desired location of screen center detailed in step 2. Measure the distance from the center of wall arm (A) to desired screen center. Loosen four 1/4-20 x 17mm screws

using 5mm allen wrench (I). Slide wall arm assembly 4-1/2" to the left or right as shown in ﬁ gure 1.1. NOTE: Align bevels (dots) of slide plate with bevels (dots) of wall plate rails as shown in detail 1 then retighten 1/4-20 x 17mm screws.

Do not adjust arm while screen is attached.

Skip to page 6 for Wood Stud Installation. Skip to page 7 for Concrete and Cinder Block Installation.

1/4-20 X 17MM SCREWS

WALL PLATE

WALL PLATE RAIL

SLIDE PLATE

DETAIL 1

ﬁ g. 1.1

5 of 56

WALL ARM

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

Installation to Double-Stud Wall

WARNING

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

• Tighten wood screws so that wall plate is ﬁ rmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁ nder is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

Use a stud ﬁ nder to locate the edges of the studs and draw a vertical line down the center of each stud. Determine

and mark the desired screen center on the wall. Place wall plate template (wall arm) on wall with top mounting slots 9" (229mm) above desired screen center as shown in ﬁ gure 2.1. Level wall plate template (wall arm) on wall and mark center of four mounting holes making sure that the mounting holes are on the stud centerlines. Drill four 3/16" (5mm) dia. pilot holes to a depth of 3" (76mm). Attach wall arm (A) to wall using four wood screws (C) as shown in ﬁ g. 2.2.

Level wall plate then tighten all fasteners.

WOOD STUD

CS = CENTER OF SCREEN

ﬁ g. 2.1

(229 mm)

WOOD STUD

6 of 56

ﬁ g. 2.2

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

Installation to Solid Concrete or Cinder Block

WARNING

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block. Cinder block must meet ASTM C-90 speciﬁ cations. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Determine and mark the desired screen center on the

wall. Place wall plate template (wall arm) on wall with top mounting slots 9" (229mm) above desired screen center as shown in ﬁ gure 2.1 on page 6. Level wall plate template (wall arm) on wall and mark center of four mounting holes making sure that the mounting holes. Drill four 3/8" (10mm) dia. pilot holes to a depth of 3" (76mm). Insert anchors (D) into holes ﬂ ush with wall as shown (right). Place wall arm over anchors and secure with 5/16 x 3" screws (C). Level, then tighten all fasteners.

WARNING

Drill holes and insert anchors (D).

Place plate (A) over anchors (D) and secure with screws (C).

concrete surface

• Tighten screws so that wall plate is ﬁ rmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete expansion anchors directly to load-bearing concrete.

• Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other ﬁ nishing material. If mounting to concrete surfaces covered with a ﬁ nishing surface is unavoidable (not evaluated by UL), the ﬁ nishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8" (16mm), custom fasteners must be supplied by installer (not evaluated by UL).

INCORRECT CORRECT

plate

CUTAWAY VIEW

wall

plaster/ dry wall

concrete

wall

plate

plaster/ dry wall

concrete

Tighten all fasteners.

SOLID CONCRETE

CINDER BLOCK

7 of 56

ﬁ g. 2.3

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

Installing Extension Brackets to Universal Adapter Brackets

Skip to step 3-1 on page 9 if not installing

extension brackets.

Remove four 1/4-20 self-tapping screws to detach screen brackets from universal adapter bracket (B) using 5mm allen wrench (I) as shown.

1/4-20 SELF-

T APPING SCREWS

HOLES

For 65" Panasonic Display: NOTE: Mount through holes ﬁ rst, then secure

through slots for proper alignment. Attach Panasonic extension brackets (L) through

holes indicated to universal adapter bracket (B) with four 1/4-20 self-tapping screws using 5mm allen wrench (I) as shown. Then secure with 1/4-20 self-tapping screws (N) through slots indicated.

SLOTS

For 65" Sharp Display: NOTE: Mount through holes ﬁ rst, then secure

through slots for proper alignment. Attach Sharp extension brackets (M) through holes

indicated to universal adapter bracket (B) with two M5 ﬂ athead screws using 5mm allen wrench (I) as shown. Then secure with two 1/4-20 self-tapping screws (N) through slots indicated.

HOLE

SLOT

SLOTS

HOLES

8 of 56

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

Installing Adapter Brackets to Screen

NOTE: If screen has a VESA 400 horizontal

mounting pattern, skip to step 3-4 or 3-5 on page

11. NOTE: For VESA 200x200 or VESA 200x100

mount hole patterns, skip to step 4 on page 12. NOTE: For dedicated PLP plate installation skip to

step 5 on page 14.

3-1

Remove four 1/4-20 x .6" screws using 5mm allen wrench (I) and loosen two 1/4-20 x 1.25" screws 1/2 turn to allow for screen bracket adjustment.

1/4-20 x 1.25" SCREWS

1/4-20 x .06" SCREWS

3-2

To prevent scratching the screen, set a cloth on a ﬂ at, level surface that will support the weight of the screen. Place screen face side down and refer to screen manufacturers instructions for removing obstructions from the back of the screen. Adjust screen brackets to align with screen mounting holes.

Measure horizontal mounting hole pattern and choose ﬁ xed stop-position from chart below.

horizontal mounting hole pattern fixed stop-position

10-3/4" - 16-1/16" (273 - 408 mm) #1 15-1/16" - 21-9/16" (383 - 548 mm) #2 20-7/16" - 27-9/16" (519 - 700 mm) #3 26-1/16" - 32-9/16" (661 - 827 mm) #4

FIXED STOP-POSTION #4

FIXED STOP-POSTION #3

FIXED STOP-POSTION #2

FIXED STOP-POSTION #1

9 of 56

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

WARNING

• Tighten screws so screen brackets are ﬁ rmly attached to screen. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.

3-3

Select the screws from the bafﬂ ed fastener pack that best ﬁ t your screen and secure to screen following step 3-4 or 3-5 on page 11.

NOTE: Top and bottom mounting holes must be used for attaching screen brackets. Middle holes should also be used where the fasteners and screens allow.

Verify that all holes are properly aligned, then tighten screws using a phillips screwdriver.

SCREEN BRACKETS

CENTER SCREEN BRACKETS VERTICALLY ON BACK OF SCREEN

SCREEN

NOTE: "X" dimensions should be equal.

"Y" dimensions should be equal.

10 of 56

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

For Flat Back Screen

3-4

Begin with the shortest length screw, hand thread screw through multi-washer and screen brackets (B) into screen as shown below. Screw must make at least three full turns into the mounting hole and ﬁ t snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the bafﬂ ed fastener pack. Repeat for remaining mounting holes, level screen brackets and tighten screws. NOTE: Spacers may not be used, depending upon the type of screen.

Skip to step 3-6.

For Bump-out or Recessed Back Screen

3-5

Begin with the longest length screw, hand thread screw through multi-washer, screen brackets (B) and spacer in that order into screen as shown below. Screw must make at least three full turns into the mounting hole and ﬁ t snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a shorter length screw from the bafﬂ ed fastener pack. Repeat for remaining mounting holes, level screen brackets and tighten screws.

SCREEN

SPACER

MULTI-WASHER

SCREW

MULTI-WASHER

SCREW

3-6

Center screen brackets horizontally and vertically on back of screen. Tighten two 1/4-20 x 1.25" screws. Reinstall four 1/4-20 x .6" screws using 5mm allen wrench (I) into appropriate ﬁ xed-stop position from chart on page 9.

1/4-20 x 1.25" SCREWS

11 of 56

1/4-20 x .6" SCREWS

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

VESA 200 x 200 or VESA 200 x 100 Mounting Pattern

Remove four 1/4-20 x .6" screws using 5mm allen wrench

(I) and loosen two 1/4-20 x 1.25" screws 1/2 turn to allow for screen bracket adjustment.

1/4-20 x .06" SCREWS

1/4-20 x 1.25" SCREWS

4-1

Remove four 1/4-20 self tapping screws to detach screen brackets from outer mount holes of universal adapter bracket (B) using 5mm allen wrench (I) as shown in ﬁ gure 4.1. Reinstall four 1/4-20 self tapping screws to secure screen brackets to inner set of mounting holes on universal adapter bracket (B) as shown in ﬁ gure 4.2.

1/4-20 SELF

T APPING SCREWS

To prevent scratching the screen, set a cloth on a ﬂ at, level surface that will support the weight of the screen. Place screen face side down and place universal adapter bracket (B) onto screen.

ﬁ g. 4.1

OUTER MOUNTING HOLES

SCREEN BRACKETS

INNER MOUNTING HOLES

SCREEN BRACKETS

1/4-20 SELF

T APPING SCREWS

ﬁ g. 4.2

12 of 56

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

VESA 200 x 200 or VESA 200 x 100 Mounting Pattern (Continued)

4-2

Align one screen bracket with one set of screen mounting holes.

Begin with the shortest length screw, hand thread screw through multi-washer and screen brackets into screen as shown. Screw must make at least three full turns into the mounting hole and ﬁ t snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the bafﬂ ed fastener pack. Center screen brackets vertically and tighten screws.

NOTE: For screens with a bump-out or recessed back, spacer may be used. Spacer goes between screen bracket and screen.

SCREW

MULTI-

WASHER

SCREEN

BRACKET

SCREEN

4-3

4-4

Slide universal adapter bracket to the opposite side and align second screen bracket with second set of screen mounting holes.

Hand thread screws through multi-washer, screen bracket, and spacer if used, into screen as shown. Tighten all screws.

Center screen brackets horizontally on back of screen as shown in ﬁ gure 4.3. Tighten two 1/4-20 x 1.25" screws. Reinstall four 1/4-20 x .6" screws using 5mm allen wrench (I) into ﬁ xed-stop

position 1 as shown in ﬁ gure 4.4.

MULTI-WASHER

1/4-20 x 1.25" SCREWS

SCREEN

SCREW

SCREEN

BRACKET

ﬁ g. 4.3

ﬁ g. 4.4

13 of 56

FIXED STOP POSITION #1 WITH

1/4-20 x .6" SCREWS

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

WARNING

• Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen.

• Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten M10 x 15mm screws (E) to 40 in. • lb (4.52 N.M.) maximum torque.

Mounting Flat Panel Screen

For Dedicated PLP Plate (not evaluated by UL):

Refer to PLP model instruction sheet for attachment of dedicated PLP plate to screen.

Install two M10 x 15mm screws (provided with dedicated PLP plate) into top two holes of dedicated PLP plate leaving 1/4" of exposed thread as shown in ﬁ gure 5.1.

For Universal Adapter Bracket: Hook M10 x 15mm screws into keyslots of wall arm adapter plate (A) as shown ﬁ gure 5.2.

SCREEN NOT SHOWN

FOR CLARITY

1/4"

5-1

DEDICATED

PLP PLATE

1/4"

M10 X 15MM

SCREW

ADAPTER PLATE

ﬁ g. 5.1

Insert two M10 x 15mm screws (E) into bottom holes of adapter plate as shown in ﬁ gure 5.3 or 5.4. Tighten all fasteners with 6mm allen wrench (H).

DEDICATED PLP PLATE

ﬁ g. 5.2

ADAPTER PLATE

ADAPTER

PLATE

ﬁ g. 5.3 ﬁ g. 5.4

14 of 56

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

Adjustment of Flat Panel Screen

WARNING

• M10 x 15mm screws (E) must be securly tightened before changing orientation of wall arm assembly (A). Failure to lock adapter bracket can cause screen to come off of mount.

FOR PORTRAIT OR LANDSCAPE SCREEN ORIENTATION: Remove two M5 x 12mm screws and rotation block

from top of tilt head as shown in top view and rear view. Gently grasp sides of screen and rotate screen into portrait or landscape position as shown in ﬁ gure 6.1 then reinstall rotation block with two M5 x 12mm screws.

ROTATION BLOCK

M5 X 12MM SCREWS

TOP VIEW

M5 X 12MM SCREWS

TIL T Adjustment: Adjust tension knob on side of

mount to desired tension to enable tilt adjustment and balance your screen size and weight. Push or pull from top or bottom of screen to adjust tilt as shown. The tilt can be adjusted to a maximum of 10° forward or 5° backward. Retighten tension knob. NOTE: For larger displays, tension screw on opposite side of mount may need to be tightened using 5/32" allen wrench (P).

ROLL Adjustment:

counter-clockwise, level screen then tighten M5 x 10mm roll screws using 5mm allen wrench (I) as shown in detail 2.

FOR VERTICAL HEIGHT ADJUSTMENT: Tighten or loosen M8 x 40mm screw to achieve ± 1" of vertical height adjustment as shown in detail 2.

Rotate screen 5° clockwise or

CAUTION

ROTATION BLOCK

REAR VIEW

ﬁ g. 6.1

TENSION KNOB

M5 X 10MM

SCREWS

• Do not tighten screws with excessive force.

• Be careful not to pinch ﬁ ngers when opening and closing mount from the wall.

15 of 56

M8 X 40MM

SCREW

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

DETAIL 2

Cable Management

NOTE: Make sure cables have enough slack to

allow full movement of the arm. Run power cable through top or bottom of arm (A)

and signal cable(s) through other side of arm in order to avoid interference with the signal. Lock cables into place by snapping cable covers (J & K) onto mount as shown. Screen may have to be moved for easy access.

Optional: If additional cable management is required route cable ties (G) through slots of arm (A) as shown in detail 3.

SLOT

CABLE

Snap wall plate covers (F) to top and bottom of wall

plate rails as shown.

DETAIL 3

WALL PLATE RAILS

16 of 56

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

Arm Tension Adjustment

WARNING

• Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the screen to fall.

• If screws become loose over time, tighten screws as necessary. Tighten screws to 50 in • lbs (5.6 N.m.) maximum torque.

If more or less tension is desired in the arm pivot points, do the following:

• To increase tension, turn socket screw clockwise with 5mm allen wrench (I). NOTE: Tighten screws to 50 in • lbs (5.6 N.m.) maximum torque.

• To reduce tension, turn socket screw counter-clockwise with 5mm allen wrench (I). NOTE: Do not turn more than half a turn.

TENSION SCREW

TENSION SCREWS

17 of 56

ISSUED: 03-09-12 SHEET #: 095-9386-2 03-26-12

+ 39 hidden pages