Peerless Industries PRS-1S, PRS-1W, PRS-1 User Manual
Installation and Assembly Manual:
PRS Series Projector Mount
Models: PRS-1, PRS-1S, PRS-1W
This product is intended for use with UL
Listed products and must be installed by a
L
USC
qualifi ed professional installer.
Features:
• ImageLockTM alignment prevents picture sag or drift
• Exclusive aluminum track quick release
U
©
Maximum UL Load Capacity:
25 lb (11 kg)
1 of 13
Visit the Peerless Web Site at www.peerlessmounts.com
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
For customer care call 1-800-865-2112 or 708-865-8870.
ISSUED: 08-15-07 SHEET #: 055-9188-6 06-25-10
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call
Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum UL Load Capacity. See page 1.
• If mounting to wood joist ceilings, make sure that mounting screws are anchored into the center of the joist. Use of an
"edge to edge" stud fi nder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed and intended to be mounted to the following supporting surfaces checked below with the
hardware included in this product as specifi ed in the installation sheet. To mount this product to an alternative sup-
porting surface, contact Peerless customer care at 1 800 865-2112.
• This product was designed to be installed on the following ceiling construction only;
CEILING CONSTRUCTION ADDITIONAL HARDWARE REQUIRED
x Wood Stud None
x Wood Joist None
x Solid Concrete None
Cinder Block Contact Customer Service (Not Evaluated by UL)
Metal Stud Do not attach except with Peerless accessory kit for metal studs;
Contact Customer Service for Peerless accessory kit for metal studs.
(Not Evaluated by UL)
Brick Contact Customer Service (Not Evaluated by UL)
Other or unsure? Contact Customer Service (Not Evaluated by UL)
Tools Needed for Assembly
• stud fi nder ("edge to edge" stud fi nder is recommended)
• phillips screwdriver
• drill
• 1/4" bit for concrete surface
• 5/32" bit for wood studs
• level
Table of Contents
Parts List............................................................................................................................................................................3
Installation to Extension Columns / Ceiling Plate ..............................................................................................................4
Installation to Wood Joist Ceilings .....................................................................................................................................5
Installation to Concrete Ceilings ........................................................................................................................................6
Installation to Threaded Rods ............................................................................................................................................7
Attaching Adapter Plate to Projector..................................................................................................................................8
Attaching Adapter Plate to Projector Mount.......................................................................................................................9
Cable Management .........................................................................................................................................................10
Projector Alignment .........................................................................................................................................................11
Accessories ...............................................................................................................................................................12, 13
ISSUED: 08-15-07 SHEET #: 055-9188-6 06-25-10
Visit the Peerless Web Site at www.peerlessmounts.com
2 of 13
For customer care call 1-800-865-2112 or 708-865-8870.
Before you start check the parts list to insure all of the parts shown are included.
Parts List
Description Qty. Part # Part # Part #
projector mount assembly 1 055-1963 055-4963 055-2963
A
4 mm security allen wrench 1 560-9646 560-9646 560-9646
B
#10-32 x 3/8" serrated washer head socket pin screw 2 520-1151 520-2151 520-2151
C
#10-32 x 1/4" socket pin screw 1 520-1196 520-2196 520-2196
D
flat washer 2 540-1078 540-1078 540-1078
E
#14 x 2.5 phillips hex head wood screw 2 5S1-015-C03 5S1-015-C04 5S1-015-C04
F
concrete anchor 2 590-0097 590-0097 590-0097
G
connection block
H
A
B
PRS-1 PRS-1S PRS-1W
1
580-1065 580-4065 580-4065
G
C
NOTE: Actual parts may appear slightly different than illustrated.
D
E
H
F
Visit the Peerless Web Site at www.peerlessmounts.com
3 of 13
ISSUED: 08-15-07 SHEET #: 055-9188-6 06-25-10
For customer care call 1-800-865-2112 or 708-865-8870.
Installation to Extension Column / Ceiling Plate
NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to
1
ceiling.
Screw projector mount assembly (A) onto extension column as shown in fi gure 1.1.
Tighten swivel stop screw against extension column, fl ush mount tube or reducer using 4 mm security t-wrench
(B) as shown in fi gure 1.2.
NOTE: Swivel stop screw is used to jam against threads of extension column, fl ush mount tube or reducer to
prevent any excess movement of projector mount assembly (A). Do not overtighten screw; overtightening screw
will damage threads making it diffi cult to separate products.
Skip to step 5.
1 1/2" EXTENSION COLUMN
(SOLD SEPARATELY)
(UL LISTED EXT OR AEC SERIES)
A
SWIVEL STOP
SCREW
fi g. 1.1
BACK OF
MOUNT
CMJ 455
(SOLD SEPARATELY)
Visit the Peerless Web Site at www.peerlessmounts.com
4 of 13
fi g. 1.2
ISSUED: 08-15-07 SHEET #: 055-9188-6 06-25-10
For customer care call 1-800-865-2112 or 708-865-8870.
Loading...