Peerless-AV PE0316 Installation Instructions

Page 1
Installation and Assembly - Vector Pro™ and PRS Projector
IMPORT ANT! Read entire instruction sheet before you start installation and assembly . IMPORT ANT! Certain types of walls require additional mounting hardware...
Models: PWA-14,
PWA-14S, PWA-14W
WALL CONSTRUCTION ADDITIONAL HARDW ARE REQUIRED
Wood Stud, Wood Beam none Solid Concrete, Cinder Concrete Anchor Kit - order accessory kit ACC200 or ACC203.
Block, Brick Metal Stud Metal Stud Kit - order accessory kit ACC415. Other or unsure? Contact customer service.
Max. Load Capacity
50 lb (22.7 kg)
Some of the following
tools may be required:
Drill, hammer, socket
wrench, pencil, stud finder
TURN TO THE APPROPRIATE PAGE FOR YOUR INSTALLATION.
Installations:
T o Wood Stud Walls.............................................................. step 2, p age 3
T o Concrete Walls...................................................................step 3, page 4
T o Metal Stud W alls.................................................................step 4, page 5
1 of 6
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
ISSUED: 03-19-03 SHEET #: 017-9011-3 06-10-04
Page 2
Parts List
Model # PWA-14 PWA-14S PWA-14W
Description
A
support arm
B
carriage bolt
C
M10 locknut
D
M10 steel washer
E
M10 bronze washer
F
#14 x 2.5 phillips wood screw
G
threaded rod adapter
H
end cap
Some parts may appear slightly different than illustrated.
Attach threaded rod adapter (G) to support arm (A) using carriage bolt (B), locknut (C), steel washer (D) and bronze washer (E) as shown. Insert end cap (H) into end of support arm (A) as shown.
Qty.
1 1 1 1 1 2 1 1
Part #
017-1019 520-1046 530-9402 540-9407 540-9441 5S1-015-C03 580-1021 590-1014
Part #
017-4019 520-2046 530-9404 540-9407 540-9441 5S1-015-C04 580-4021 590-4014
B
Part #
017-2019 520-2046 530-9404 540-9470 540-9441 5S1-015-C04 580-2021 590-1001
F
A
H
D
G
E
C
2 of 6
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
ISSUED: 03-19-03 SHEET #: 017-9011-3 06-10-05
Page 3
Installation to a wood stud wall
Drill two 5/32" (4 mm) dia. holes 2 1/2" (65 mm) deep. Attach wall arm (A) with #14 x 2.5"(6 mm x 65 mm) wood screws (F).
WARNING
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly recommended.
5/32"
(4 mm)
A
5/32"(4 mm)
F
A
3 of 6
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
ISSUED: 03-19-03 SHEET #: 017-9011-3 06-10-04
Page 4
Installation to a concrete wall
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica­tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity .
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor .
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hard­ware and components.
Drill two 1/4" (6 mm) dia. holes to a minimum depth of
2.5" (64 mm). Attach support arm (A) using concrete anchors(call customer service to order accessory kit ACC
200 or ACC203)
shown in Illustration A and 1, 2, and 3. Tighten all fasteners.
and #14 x 2.5" wood screws (F) as
1
concrete wall
concrete anchor
WARNING
Drill hole and insert anchor
• Tighten wood screws firmly , but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
2
F
A
concrete anchor
concrete anchor
A
F
Illustration A
WARNING
• Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster, drywall, or other finishing material. If mounting to concrete wall covered with plaster/drywall is unavoidable, plaster/ drywall (up to 5/8" thick) must be counterbored as shown below. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer .
Place wall plate over anchor and secure with screw
3
concrete
F
After repeating step one tighten all fasteners
INCORRECT
CUT AW A Y VIEW
metal bracket
metal bracket
plaster/ dry wall
CORRECT
plaster/ dry wall
concrete
concrete
anchor
4 of 6
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
ISSUED: 03-19-03 SHEET #: 017-9011-3 06-10-05
Page 5
Installation to a metal stud wall
WARNING
• Product must be mounted through drywall that has a minimum thickness of 1/2" and into metal studs, 26 gauge or heavier.
Drill 1/2" (13 mm) dia. holes through drywall and stud. Insert togglers (call customer service to order accessory kit ACC 415) as follows.
Important: Product must be mounted through drywall that has a minimum thickness of 1/2" and into metal studs, 26 gauge or heavier.
Pivot end of toggler.
toggler
1/2"(13 mm)
Push into hole.
Slide plastic cap forward while pulling back firmly on ring.
Snap off as shown.
A
1/4-20 x 2.5" phillips screw
Attach wall arm with 1/4-20 phillips screws.
5 of 6
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
ISSUED: 03-19-03 SHEET #: 017-9011-3 06-10-04
Page 6
Thread projector mount onto threaded rod adapter (G) as shown. Note: Make sure the notch in threaded rod adapter (G) is aligned with one of the four holes at the top of the PJC 100.
Note: Installation PRS-1 not shown. Please refer to PRS model instructions to attach PRS mount to PWA-14.
G
PJC 100 (not included) (PRS-1 not shown)
Secure PJC 100 to threaded rod adapter (G) with one #10-32 x 3/8 socket pin screw provided with PJC 100.
Note: Installation PRS-1 not shown. Please refer to PRS model instructions to attach PRS mount to PWA-14.
#10-32 x 3/8 socket pin screw
Refer to PJC 100 or PRS model instructions for attachment of projector .
6 of 6
Visit the Peerless Web Site at www.peerlessmounts.com For customer service call 1-800-729-0307 or 708-865-8870.
© 2004 Peerless Industries, Inc. All rights reserved. Peerless is a registered trademark of Peerless Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 03-19-03 SHEET #: 017-9011-3 06-10-05
Loading...