Peavey PV MICROPHONE DATASHEET

@

PV
Microphone

SPEClFlCATIO/VS

Element Type:

Dynamic

Polar Pattern:

Cardioid

Front-to-Back Rejection:

17 dB

typical

Impedance:

Low Z (500 ohms,

Frequency Response:

50 to

14,000 Hz

Sensitivity:

Output Power Level:

-59 dB (0 dB = Im

w/IO

microbars*)

Open Circuit Voltage:

-75 dB (0 dB = 1 volt/dyne/cm2)

Case (Housing):

Die-cast alloy

Finish:

Low-gloss

Windscreen:

Brazed

Pop Filter:

Integral acoustic

Connector:

3 pin

Switch:

Slide

Phasing:

Positive
diaphragm produces positive voltage
at pin #2

Weight:

8 oz. (227

*IO

microbars = 1

10 dynes/cm2

black

steel

XLR-type

on/off,

(inward)

grams)

FEATURES:

l On/off switch in handle
l Clean, natural sound
l Cardioid unidirectional polar

response

l Low pop and handling noise

balanced)

mesh

foam

shorting

pressure

Pascal =

on

l Rugged die-cast and steel case
l Low-gloss black finish

DESCRIPTION:

The

PV@

is a cardioid unidirectional
dynamic microphone designed for
applications in which a built-in “on/off”
switch is desired. With a clean, natural
speech response and good noise and
feedback rejection, the PV is an ideal
microphone for vocals, church and
institutional systems, meeting rooms,

auditoriums, and some instruments
almost anywhere in which convenient
local control of the microphone is
required. The PV mic has been

-

re-fashioned to make it attractive in any
setting. An integral acoustic foam pop
and wind filter provides effective control
of plosive sounds and moderate wind.
The internal shock-mounting system
minimizes handling and stand noise.
The PV is a rugged, reliable
microphone well-suited for rental
systems, convention centers and similar
rough usage applications. The PV mic
gives the look, feel, and performance of
expensive professional microphones at
a fraction of the price. Also available
in Hi

Z.

NOTE: The switch mutes the

microphone by directly shorting across
the dynamic element. Microphones with
this type of switching should not be
used if more than one microphone is
connected to the same input, since the
“off” function on one microphone will
also short any other unit connected to
that input. If this type of operation is
required, the use of a transformer-type
microphone combiner is suggested.
(Another possible alternative is to rewire
the PV so that the switch is used to
open one side of the line for

(‘off.“)

100

50

50 100

I I I I

Figure 2. Proximity Effect

200

200 500

500 1 k 2 k

Figure 1. Frequency Response

5k

lok

1

k

1

Proximity effect is a naturally
occurring phenomenon in
unidirectional microphones. The
effect is to accentuate or boost the
low frequency response. This
effect is a function of distance
from the diaphragm to the source
and increases as the diaphragm is

moved closer to the source.

20 k

For high impedance

mics,

cable lengths
of 25’ or more and input impedance
not less than 20 kilohms are not
recommended due to loss of signal
quality.

ARCHITECTURAL
SPECIFICATIONS

The microphone shall be a moving
coil dynamic type with a frequency
response of 50 Hz to 14
microphone shall have a cardioid polar
characteristic with a rear response that
is 15 to 20 dB down.

The microphone shall include a
handle-mounted “on/off” switch slide
type with positive action which
circuits the microphone output. The
microphone shall have non-reflecting,
low-gloss paint on a die-cast alloy
housing and a brazed metal screen.
The connector shall be a
equivalent audio type. The microphone
shall have overall dimensions of
length and

13/4”

in diameter. The

microphone shall be a Peavey

Electronics model PV or equivalent. This
microphone will also have a high
impedance model that shall be the

PV Hi

Z.

kHz.

3-pin

The

short-

XLR

6V2”

in

50

100

200

Figure

500 1 k 2 k

3.0”

and

180”

Response

5k

10k

20 k