Patton electronic 2173R User Manual

USER
MANUAL

MODEL 2173R

Ruggedized High Speed
Ethernet Extender

An ISO-9001Certified

Company

Part# 07M12173R-UM
Rev. B
Revised 2/3/12

SALES OFFICE
[phone]
TECHNICAL SUPPORT
[phone]

CONTENTS

1.0 Warranty Information ................................................................. 4

1.1 Compliance................................................................................... 4

EMC Compliance:......................................................................... 4

Low-Voltage Direcive (Safety):..................................................... 4

PSTN:.................................................. ..... ...... ..... ...... ................... 4

1.2 Radio and TV Interference (FCC Part 15) .................................... 4

1.3 CE Declaration of Conformity ....................................................... 5

1.4 Authorized European Representative........................................... 5

1.5 Service.......................................................................................... 5

1.6 Safety When Working With Electricity .......................................... 6

2.0 General Information.................................................................... 8

2.1 Features........................................................................................ 8

2.2 Description.................................................................................... 8

3.0 Installation................................................................................... 9

3.1 Connecting the Twisted-Pair Line Interface................................ 10

3.2 Connecting the 10/100Base-T Ethernet Interface ...................... 11

3.3 Connecting Power ......................... ............................................. 12

4.0 Configuration ............................................................................ 12

4.1 Configuring the hardware DIP switches..................... ...... ........... 12

4.2 Configuring DIP Switch S1......................................................... 14

5.0 Operation................................................................................... 14

5.1 Power Up.................................................................................... 14

5.2 Front Panel LED Status Monitors ............................................... 15

A

Specifications ........................................................................... 16

A.1 LAN Connection ......................................................................... 16

A.2 Transmission Line ....................................................................... 16

A.3 CopperLINK Line Rate and CopperLINK Distance .................... 16

A.4 LED Status Indicators ................................................................. 16

A.5 Power Supply .............................................................................. 16

A.6 Temperature Range .................................................................... 16

A.7 Humidity ...................................................................................... 16

A.8 Dimensions ................................................................................. 16

B

Model 2173R Factory

Replacement Parts and Accessories ...................................... 17

C

Model 2173R Interface Pin Assignment.................................. 18

C.1 10/100Base-T Interface .............................................................. 18

RJ-45.......................................................................................... 18

C.2 CopperLINK Interface ................................................................ 18

RJ-45.......................................................................................... 18

2

D

Sample Rates/Distance Chart, Based on 24 AWG (0.5 MM) . 19

3

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 2173R components to be free
from defects, and will—at our opti on —repair or replace the product
should it fail within one year from the first date of the shipment.

This warranty is limited to de fects in workmansh ip or material s, and does
not cover customer damage, abuse or unauthorized modification. If this
product fails or do es not perfo rms as warrante d, you r so le reco urse shal l
be repair or replacement as described above. Under no condition shall
Patton Electronics be liable for any damages incurred by the use of this
product. These dama ges include , but are not limite d to, the follow ing: lost
profits, lost savings and incidental or consequential damages arising
from the use of or inability to use this product. Patton Electronics spe

­cifically disclaims all other warranties, expressed or implied, and the
installation or use of this product shall be deemed an acceptance of
these terms by the user.

Note Conformity documents of all Patton products can be viewed

online at www.patton.com under the appropriate product page.

1.1 COMPLIANCE

EMC Compliance:

• FCC Part 15, Class A

• EN55022, Class A

• EN55024

• A-tick

Low-Voltage Direcive (Safety):

• IEC/EN60950-1, 2nd Edition

• AS/NZS 60950-1, A-tick

PSTN:

• This device is not intended nor approved for connection to the PSTN.

1.2 RADIO AND TV INTER FERENCE (FCC PART 15)

This equipment generates and uses radio frequency energy, and if not
installed and used properly—that is, in strict accordance with the manu
facturer's instructions—may cause interference to radio and television

4

-

reception. This eq uip me nt h as bee n tested and found to comply with the
limits for a Class A computing device in accordance with the specifica

­tions in Subpart B of Part 15 of FCC rules, whic h are designed to prov ide
reasonable protection from such interference in a commercial installa

­tion. However, there is no guarantee that interference will not occur in a
particular installation. If the equipment causes interference to radio or
television reception, which can be determined by disconnecting the
cables, try to correct the interference by one or more of the following
measures: moving the computing equipment away from the receiver, re­orienting the rece iving anten na, and /or plu gging the rec eivi ng equ ipmen t
into a different AC outlet (such that the computing equipment and
receiver are on different branches).

1.3 CE DECLARATION OF CONFORMITY

We certify that the apparatus described above conforms to the require­ments of Council Directive 2004/108/EC on the approximation of the
laws of the member states relating to electromagnetic compatibility; and
Council Directive 2006/95/EC on the approximation of the laws of the
member states relating to electrical equipment designed for use within
certain voltage limits.

The safety advice in the doc um entation accompanying this pro duc t s hall
be obeyed. The conformity to the above directive is indicated by the CE
sign on the device.

1.4 AUTHORIZED EUROPEAN REPRESENTATIVE

D R M Green, European Compliance Services Limited.
Avalon House, Marcham Road, Abingdon, Oxon OX14 1UD, UK

1.5 SERVICE

All warranty and non-warranty repairs must be returned freight prepaid
and insured to Patton Electro nic s. All retu rns mus t hav e a Ret urn M ate ri
als Authorization number on the outside of the shipping container. This
number may be obtained from Patton Electronics Technical Services at:

•Tel: [phone]

•Email: [e-mail]

• URL: http://www.patton.com

Note Packages received without an RMA number will not be

accepted.

5

-

1.6 SAFETY WHEN WORKING WITH ELECTRICITY

• This device contains no user serviceable parts. This
device can only be repaired by qualified service per
sonnel.

• Do not open the device when the power cord is con­nected. For systems without a power switch and without
an external power adapter, line voltages are present
within the device when the power cord is connected.

• For devices with an external power adapter, the power
adapter shall be a listed Limited Power Source. The
mains outlet that is utilized to power the device shall be
within 10 feet (3 meters) of the device, shall be easily
accessible, and protected by a circuit breaker in com
pliance with local regulatory requirements.

• For AC powered devices, ensure that the power cable
used meets all applicable standards for the country in
which it is to be installed.

• For AC powered devices which have 3 conductor
power plugs (L1, L2 & GND or Hot, Neutral & Safety/

WARNING

Protective Ground), the wall outlet (or socket) must
have an earth ground.

-

-

• For DC powered devices, ensure that the interconnect­ing cables are rated for proper voltage, current, antici­pated temperature, flammability, and mechanical
serviceability.

• WAN, LAN & PSTN ports (connections) may have haz­ardous voltages present regardless of whether the
device is powered ON or OFF. PSTN relates to inter
faces such as telephone lines, FXS, FXO, DSL, xDSL,
T1, E1, ISDN, Voice, etc. These are known as “hazard
ous network voltages” and to avoid electric shock use
caution when working near these ports. When discon
necting cables for these ports, detach the far end con­nection first.

• Do not work on the device or connect or disconnect
cables during periods of lightning activity.

-

6

-

-