Patton electronic 1195-4E1 User Manual

Model 1195/4E1

Optical Multiplexer

Quick Start Guide

Part Number: 07M1195-QS, Rev. A
Revised: February 12, 2009

Sales Office: [phone]

Technical Support: [phone]

E-mail: [e-mail]

WWW: www.patton.com

WARNING

• This device contains no user serviceable parts. The equipment shall be
returned to Patton Electronics for repairs, or repaired by qualified
service personnel.

• Mains Voltage: Line voltages are present when the power cord is con­nected. The mains outlet shall be within 10 feet (3 meters) of the
device, shall be easily accessible, and protected by a circuit breaker.

• For AC powered units, ensure that the power cable used meets all
applicable standards for the country in which it is to be installed, and
that it is connected to a wall outlet which has earth ground.

• Hazardous network voltages are present in WAN ports, regardless of
whether power to the unit is ON or OFF. To avoid electric shock, use
caution when near WAN ports. When detaching the cables, detach the
end away from the unit first.

• Do not work on the system or connect or disconnect cables during
periods of lightning activity.

• For units with an external power adapter, the adapter shall be a
listed Limited Power Source.

2

Model 1195/4E1 Quick Start Guide

1.0 Connecting power

AC Mains version:

Please use the AC main cable (provided) to connect the system to your AC mains power

outlet.

DC Mains version

: Please connect the DC mains cable (provided) to the system. The polarity should not be

reversed while connecting. Otherwise, you can get your system damaged.

1.1 AC Power

To connect the AC 220V power:

DC 48 V

~ 220 V

PGND

IEC 60320

Male on Unit

OPTICAL B

GND

-48V

TX RX

OPTICAL A

TX RX

IEC 60320

Female

From AC Source
(220V)

E1 4-1

II

1.2 DC Power

To connect the DC -48V:

CONSOLE

RS232

DC 48 V

~ 220 V

PGND

GND

-48V

DC Power

Cable

Model 1195/4E1 Quick Start Guide

OPTICAL B

TX RX

OPTICAL A

TX RX

E1 4-1

II

CONSOLE

RS232

3

1.3 Grounding

When the equipment is used with the AC~220V power supply, the 3-core socket must be grounded for protec­tion.The other equipment, e.g. optical terminal, connected with this equipment must also be grounded

To connect the Earth:

DC 48 V

~ 220 V

PGND

GND

OPTICAL B

-48V

TX RX

OPTICAL A

TX RX

E1 4-1

II

CONSOLE

RS232

DC 48 V

~ 220 V

Earth Wire

2.0 Connecting the optical interface

PGND

GND

-48V

through Optical

OPTICAL B

Optical Signal

Fiber Cable

TX RX

Transmit

OPTICAL A

TX RX

E1 4-1

II

CONSOLE

RS232

Receive

Optical Signal

through Optical

Fiber Cable

Note: Do not expose to the naked eye.
Connect fiber cable to system
when power is OFF.

ar nE th Poi t

Note

Do not expose to the naked eye. Connect fiber cable to system when power is OFF.

Note

For Testing:

ALWAYS INSTALL OPTICAL ATTENUATORS. For distances of less than 10 km, optical attenuators

must be installed on the Optical Links. Otherwise, the optics will be permanently damaged.

4

Model 1195/4E1 Quick Start Guide

3.0 Connecting the DB-37 connector

DC 48 V

~ 220 V

PGND

OPTICAL B

TX RX

OPTICAL A

TX RX

GND

-48V

E1 4-1

II

CONSOLE

RS232

19

1

DB-37 (Female)

Connector

1

RJ-45 (F)

Connector

2

RJ-45 (F)

Connector

4xE1 Signals

18

37

3

RJ-45 (F)

Connector

4

RJ-45 (F)

Connector

Model 1195/4E1 Quick Start Guide

5

4.0 Connecting E1 Links

Connect E1 line after ensuring that transmission device have been grounded. A Bit Error Rate (BER) test may be
conducted on E1 Link using a BERT tester to ensure that the E1 errors are within the permitted limits / threshold.

4.1 Definition for E1 Interfaces

The E1 Interface (RJ-45 connector) is defined as:

1 2 3 4 5 6 7 8

Rx+ Rx- N/C Tx+ Tx- N/C N/C N/C

Data In + Data In - Data Out + Data Out -

5.0 Connecting Ethernet Links

Please configure the Ethernet port of the equipment at both sides as well as the Ethernet Ports of the devices that
are connected to the equipment. Connect the Ethernet links.

Please ensure that the connecting LANs on both sides of the link are operating in the same IP domain.

5.1 Verifying the connection

Ping over the Ethernet connection from one side to the other (near-end to the far-end) to verify the link.

5.2 Definition for Ethernet Interfaces

The Ethernet Interface (RJ-45 connector) is defined as:

1 2 3 4 5 6 7 8

Tx+ Tx- Rx+ N/C N/C Rx- N/C N/C

Data Out + Data Out - Data In + Data In -

6

Model 1195/4E1 Quick Start Guide

6.0 Connecting the RS-232 port

DC 48 V

~ 220 V

PGND

OPTICAL B

GND

-48V

TX RX

OPTICAL A

TX RX

Settings:

1 Bits per second 19200
2 Data bits 8
3 Parity None
4 Stop bits 1
5 Flow control None

DB9 (Male)

Connector

E1 4-1

II

DB9 Connector (Male)

CONSOLE

DB9 Connector (Female)

RS232

PC

Note

An RS-232 COM port cable is provided with the 1195/4E1 system.

6.1 RS-232 port cable details

End 1
End 2

DB-9 (Female Connector)
DB-9 (Female Connector)

Type of cable Twisted pair cable - solid conductor
Number of pairs 2
Diameter 24 AWG
Length 3 meters
Connections As per details given below

Model 1195/4E1 Quick Start Guide

DB9 (Female)

Connector

7

6.2 RS-232 pin definition

DB-9 Pin Number Definition

2 RS-232 input signal for management
3 RS-232 output signal for management
5 GND

RS-232

Others NC

8

Model 1195/4E1 Quick Start Guide

7.0 Configuring HyperTerminal

1.

Click on the Start button from the task bar on your PC.

2.

Select Programs > Accesories > Communications > HyperTerminal. The following screen will display:

3.

Enter a name for the new connection and click OK. The connection window will display:

4.

Select the COM port from the drop-down menu, and click OK. The properties window will display:

Model 1195/4E1 Quick Start Guide

9

5.

Change the Bits per second option to 19200 and change the flow control option to None.
The COM Properties settings should be:

Bits per second
Data bits
Parity
Stop bits
Flow control

6.

Click Apply, then click OK.

7.

A new HyperTerminal session screen will display. Press Enter. The system prompt will appear on the

19200
8
None
1
None

screen. This prompt is generated by the system. Now, you may access/configure the system with the CLI
commands.

Note

Remember to save the settings for future use before you exit the HyperTerminal window.

Note

For detailed information about configuring the 1195/4E1 system using CLI commands or the Graphi­cal User Interface (GUI), refer to the

Model 1195/4E1 Getting Started Guide

that came with your unit.

10

Model 1195/4E1 Quick Start Guide

8.0 Additional Information

Refer to the

Model 1195/4E1 Getting Started Guide

located on the CD-ROM shipped with your device

For detailed information about:

•

Installing, configuring, operating, and troubleshooting

A.0 Customer and Technical Support

Toll-Free VoIP support: call
Online support: www
E-mail support:

[e-mail]

Telephone support:

Standard: [phone] (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

•

2200 UTC/GMT)
Alternate: [phone] (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

•

UTC/GMT)

Fax:

[phone]

sip:[e-mail]

.patton.com

(USA)

or [phone] (

with a VoIP SIP client

—answered within 1 business day

Switzerland)

.

Model 1195/4E1 Quick Start Guide

11

Copyright statement

Copyright © 2009, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

In accordance with the requirements of council directive 2002/96/EC on Waste of
Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate
this product from other waste and scrap and deliver to the WEEE collection system in
your country for recycling.

12

Model 1195/4E1 Quick Start Guide