Patton electronic 1092A User Manual

Page 1
F
EATURES
F
EATURES
7622 Rickenbacker Dr., Gaithersburg, MD 20879
Phone: (301) 975-1000 • Fax: (301) 869-9293 • E-mail: sales@patton.com • WWW: http://www.patton.com
KiloModem
KiloModem
2-W
2-W
e/4-W
e/4-W
e Baseband Modem
e Baseband Modem
Synchronous data rates of 32, 56, 64
and 128 kbps in all clock modes (Asynchronous data rates to 38.4 kbps)
Full duplex operation over one or two
twisted pairs (2 or 4 wires)
4-Wire distances up to 18 km (all data
rates) on 19 AWG twisted pair
Replaceable interface modules: G.703,
V.35, X.21, RS-422/530, V.24 (RS-232), Ethernet WAN bridge & data + voice
2B1Q Modulation
In-Band and Out-of-Band remote
management capabilities
The Patton Model 1092A
KiloModem™
supports point-to-point, synchronous or asynchronous communication over one or two twisted pairs (2 or 4 wires). Offering switch selectable synchronous data rates of 32, 56, 64 and 128 kbps, the
KiloModem™
also supports asyn-
chronous speeds up to 38.4 kbps. The
Kilo-Modem™
is an excellent choice for connecting two bridge/routers, or for simi­lar networking applications at distances up to 11.4 miles/18.2 km (4 wires).
Using the 2B1Q modulation scheme, the
KiloModem™
is able to send remote management information on the “D” channel. This means that a terminal con­nected to the
KiloModem’s
RS-232 con-
trol port can be used to send in-band
Continued...
The Patton Model 1092A
Page 2
Transmission Format: Sync or Async Transmission Line: Full duplex over one or two
unconditioned twisted pairs (2 or 4 wires) Line Encoding: 2B1Q with Integrated Echo
Cancellation.
Clocking: Internal, external or receive loopback Distance: Up to 11.4 m/18.2 km (see table below) Data Rates: 32, 56, 64, 128, synchronous (switch
selectable); 0 - 38.4 kbps, asynchronous
Carrier Control: “Constantly on” or “Contr. by RTS” RTS/CTS Delay: no delay, short delay (4-8 ms), or
long delay (33-58 ms) Diagnostics: local analog loopback, remote digital
loopback, V.52 compliant bit error rate pattern (511/511E pattern) generator and detector with error injection mode
LED Status Indicators: Dual red/green LEDs for TD, RD, CTS and DC; green for DTR; red for ER, TM and NS
Isolation & Protection: 1500V RMS (gas tube surge protection optional)
DTE Interface: Depends upon interface module
Twisted Pair Interface: RJ-45 jack Power: 120/230 VAC (switch selectable), 50/60 Hz;
100 - 240 VAC, 50/60 Hz (universal input option); 48 VDC (option). 5 watts.
Compliance: CE Marked per EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC. UL and cUL Safety Approvals.
Dimensions: 7.3” x 6.6” x 1.62” (185mm x 168mm x 41mm)
Weight: 2.02 lbs.
7622 Rickenbacker Dr., Gaithersburg, MD 20879 Phone: (301) 975-1000 • Fax: (301) 869-9293 • E-mail: sales@patton.com • WWW: http://www.patton.com
Factory Part Numbers:
1092A/IM/ PS/ Z
Interface Modules: IM = A = V24, DB25F
B = RS422/RS530, DB25F C = V35, M34F D = X21, DB15F
F = G703, RJ45 G = V.24, DB-25F (Async 57.6/115.2 kbps) I = Ethernet WAN Bridge, RJ-45F J = Data + Voice Combination (modular ports)
Power Supplies: PS = 120 = Switchable 120/230 Configured 120V
230 = Switchable 120/230 Configured 230V UI = Universal Input Supply 100-240VAC 48 = 48 VDC
Power Cord Sets:
K =American, A=European CEE 7, D=United Kingdom, C=Australia, E=Denmark, F=France/Belgium, G=India, H=Israel, J=Japan, L=Switzerland. (Others Available)
Power Cord
Power Supply
Interface Module
Base Unit
Examples: 1092A/A/120/A (V.24
DB-25F
interface module, 120 VAC power supply, US power cord)
1092A/E/230/D (G.703
RJ-48S
interface module, 230 VAC power supply, UK power cord)
S
PECIFICATIONS
S
PECIFICATIONS
Data Rate
(kbps)
128 11.4
(18.2) 7.6 (12.1) 5.3 (8.5) 3.6 (5.7)
64 11.4 (18.2) 7.6 (12.1) 5.3 (8.5) 3.6 (5.7) 56 11.4 (18.2) 7.6 (12.1) 5.3 (8.5) 3.6 (5.7) 32 11.4 (18.2) 7.6 (12.1) 5.3 (8.5) 3.6 (5.7)
0 - 38.4 11.4 (18.2) 7.6 (12.1) 5.3 (8.5) 3.6 (5.7)
Model 1092A 4-Wire Distances - Miles (Km)
Wire Gauge (AWG/mm)
19 (.7mm) 22 (.6mm) 24 (.5mm) 26 (.4mm)
O
RDERINGINFO
O
RDERINGINFO
Model 1092A
KiloModem™
, 2/4-wire,
sync/async baseband modem
Data Rate
(kbps)
128 10.8
(17.3) 7.2 (11.5) 5.0 (8.0) 3.4 (5.5)
64 10.8 (17.3) 7.2 (11.5) 5.0 (8.0) 3.4(5.5) 56 10.8 (17.3) 7.2 (11.5) 5.0 (8.0) 3.4(5.5) 32 10.8 (17.3) 7.2 (11.5) 5.0 (8.0) 3.4(5.5)
0 - 38.4 10.8 (17.3) 7.2 (11.5) 5.0 (8.0) 3.4(5.5)
Model 1092A 2-Wire Distances - Miles (Km)
Wire Gauge (AWG/mm)
19 (.7mm) 22 (.6mm) 24 (.5mm) 26 (.4mm)
Page 3
configuration and control commands to both the local and remote
KiloModems™.
In addition, the
KiloModem™
is able to send an out-of-band alarm signal through its control port.
The
KiloModem™
incorporates local analog and remote digital loopback test modes, as well as a V.52 BERT pattern generator. Eight front panel LED indica­tors (TD, RD, CTS, CD, DTR, No Signal, Error, and Test Mode) provide real-time
diagnostic information. Extended dis­tances are accomplished using automatic equalization, gain control and echo can­cellation. Data integrity is enhanced by transformer isolation and surge protec­tion. Synchronous clocking options include internal, external and receive recovered clock. For flexible connection of WAN hardware, the
KiloModem™
accepts replaceable
QuikConnect™
interface modules. These modules adapt to a variety of popular terminal interfaces (see below). Standard AC power supply options include 120/230VAC (switchable) or 85-256VAC (universal). A 48VDC power supply is also available.
7622 Rickenbacker Dr., Gaithersburg, MD 20879 Phone: (301) 975-1000 • Fax: (301) 869-9293 • E-mail: sales@patton.com • WWW: http://www.patton.com
D
ESCRIPTION
Continued...
S
PECIAL
F
EATURE
Ethernet Bridge QuikConnect™
Interface Modules
RS-232, 422, 530
64K G.703
V.35
Ethernet Bridge
X.21
Voice + Data
The Ethernet Bridge QuikConnect Module Module (model no. IM1/I) adds transparent Ethernet bridging capability to all its CSU/DSU, fiber, shorthaul, baseband, and transmission products. Now, two remote LANs can be peered across a 2/4 wire leased line, T1 (DSX-1), G.703 (64K and E1), multi­mode fiber or 56/64 kbps DDS network through a screw-in QuikConnect package. The Ethernet Bridge Module is a Media
Access Control (MAC) layer bridge and is transparent to layer-3 network protocols. It can be used in many environments, including IP, IPX, NetBIOS and DECnet™LANs. The Ethernet Bridge Module connects to an 802.3 Ethernet LAN using a standard 10BaseT interface with an RJ45 connector. Its trans­parent bridging function allows broadcast, multicast and data frames to be passed.
Page 4
7622 Rickenbacker Dr., Gaithersburg, MD 20879
Phone: (301) 975-1000 • Fax: (301) 869-9293 • E-mail: sales@patton.com • WWW: http://www.patton.com
The Ethernet Bridge Module is a likely solution for connecting LANs over fiber or copper in a campus. It can also be used to connect LANs between remote branches or satellite offices and the head office. In wide area networks, the Ethernet Bridge Module connects LANs across distances up to 18.2km at speeds up to 2.048Mbps.
The screw-in QuikConnect package allows the Ethernet Bridge Module to be installed into the rear panel of any Patton transmission product with two thumb­screws. No tools are necessary. Dual LEDs monitor the Ethernet link and CPU status. Scalable onboard RAM allows the Ethernet Bridge Module to buffer up to 4,000 frames.
Up to 4,096 MAC addresses are dynami­cally learned by the Ethernet Bridge Module and addresses age out of the table after a period of inactivity.
A
PPLICATIONS
Cash Register
ATM
Machine
Ethernet Hub
2W/4W/MMF
circuit
Patton Modem
Patton Modem
Point Of Sale
Terminal
10BaseT
VSAT Station
Ethernet Bridge
LAN Interface 10BaseT to 802.3 Ethernet via RJ45 connector LAN Address Table 4,096 MAC addresses Frame Latency 1 frame Frame Buffer 512 frames (standard), upgradeable to 4,000 frames
WAN throughput Up to 2Mbps dependent on transmission product Address Aging 1-20 minutes (factory configured)
Approvals FCC Patt 15, Class A; CE Mark per EEC Directive
89/336/EEC and Low Voltage Directive 73/23/EEC
Dimensions 2.9" x 3.2" (7.36 x 8.12 cm)
Ethernet Bridge Module Specifications
Ethernet Bridge Module
Loading...