IM250A
19
IMPORTANT!
DO NOT DESTROY
It is the customer's responsibility to have
all operators and service personnel read
and understand this manual.
OPERATING MANUAL
16 GAUGE CORDLESS
ANGLED
FINISH NAILER
Model: IM250A
Part No. 900600
Angled Finish Nailer
Printed in U.S.A.
© 2002 Illinois Tool Works, Inc.
405630-9
03/02
www.paslode.com
P
CORDLESS
1
Contents
Subject Page
Introduction and Warranty............................................... 2
An Overview of the Paslode
Angled Finish Nailer........... 3
Safety Instructions...........................................................4
Battery and Charger........................................................ 7
Fuel Cell and Metering Valve .......................................... 9
Preparing the Paslode Angled Finish Nailer for Use..... 12
Paslode Angled Finish Nailer Operation ....................... 13
Fasteners and Applications........................................... 14
Servicing ....................................................................... 15
Troubleshooting ............................................................ 17
The Impulse
®
battery charger system meets all safety
requirements for power tools.
is a trademark
Paslode
An Ilinois Tool Works Company
888 Forest Edge Drive
Vernon Hills, Illinois 60061
www.paslode.com
Power Nailers are made in the U.S.A. and are
protected by one or more of the following U.S. patents:*
4,403,722 4,483,280 4,483,474 4,522,162
*Other patents issued and pending.
Paslode
®
is a member of:
P
P
CORDLESS
CORDLESS
2
Introduction and Warranty
Paslode
Angled Finish Nailer
Operating
Manual
This manual is intended to acquaint you with the Paslode
Cordless Angled Finish Nailer. Unlike other power fastening
tools, the Paslode Angled Finish Nailer is powered by an
internal combustion linear motor. In simpler terms, your
Paslode Angled Finish Nailer is powered by a motor similar
to the one that powers an automobile. The Paslode Angled
Finish Nailer ignites a fuel and air mixture to produce the
energy to drive the motor, which in turn drives the fastener.
The Paslode Angled Finish Nailer is totally self-contained.
It carries its own fuel supply and battery, along with a supply
of fasteners.
For ease of use, this manual is divided into sections (see
Contents). Each section of the manual is written with you,
the tool operator, in mind. We have left out many of the
technical terms so that you can easily understand how to get
the maximum performance from your Paslode Angled Finish
Nailer, and how to avoid damaging the tool or injuring
yourself. But, to accomplish this, we need you to do two
things:
1. READ THE MANUAL FROM COVER TO COVER
BEFORE USING THE TOOL.
2. FOLLOW ALL INSTRUCTIONS IN THE MANUAL.
The Paslode Finish nailer should be handled like other
power fastening tools that you use. Like most tools, when
used improperly injury could result . If you are going to
allow others to use the Paslode Finish nailer, it is your
responsibility to make sure that they also read and comply
with the instructions in this manual before attempting to
operate the tool.
Should you have questions about the Paslode Finish
nailer, or wish to obtain additional copies of this manual,
please contact your Paslode
®
representative. The space
below is provided so that you may record your
representative's name, address, and telephone number.
For the nearest Paslode representative call 1-800-
682-3428
Name
Address
City State Zip
Telephone Number
Paslode Cordless Warranty and Limitations
Paslode warranties that new Impulse
®
power fastening tools,
parts and accessories will be free from defects in material and
workmanship for the period shown below, after the date of
delivery to the original user.
ONE-YEAR LIMITED WARRANTY
A one-year warranty will apply to all parts, except those listed
below as normal wearing parts, or parts which are specifically
covered by an extended warranty.
FIVE-YEAR EXTENDED LIMITED WARRANTY
A five-year warranty will apply to all molded nylon parts:
• Cap and Grille
• Handle Halves and Actuator
• Trigger
90-DAY LIMITED WARRANTY
A 90-day warranty applies to the following parts, which are
considered normal wear parts:
• Bumper
• Driver Blades
• O-Rings
WARRANTY STATEMENT
Paslode's sole liability hereunder will be to replace any part or accessory
which proves to be defective within the specific time period. Any replacement
part or accessory provided in accordance with this warranty will carry a
warranty for the balance of the period of warranty applicable to the part it
replaces. This warranty does not apply to part replacement required due
to normal wear.
This warranty is void on any tool which has been subjected to misuse,
abuse, accidental or intentional damage, use with fasteners, fuel, batteries,
or battery chargers not meeting Paslode specification, size, or quantity,
improperly maintained, repaired with other than genuine Paslode
replacement parts, damaged in transit or handling, or which, in Paslode's
opinion, has been altered or repaired in a way that affects or detracts from
the performance of the tool.
PASLODE MAKES NO WARRANTY, EXPRESSED OR IMPLIED,
RELATING TO MERCHANTABILITY, FITNESS, OR OTHERWISE,
EXCEPT AS STATED ABOVE, and Paslode's liability AS STATED ABOVE
AND AS ASSUMED ABOVE is in lieu of all other warranties arising out of,
or in connection with, the use and performance of the tool, except to the
extent other wise provided by applicable law. PASLODE SHALL IN NO
EVENT BE LIABLE FOR ANY DIRECT, INDIRECT, OR CONSEQUENTIAL
DAMAGES, INCLUDING, BUT NOT LIMITED TO, DAMAGES WHICH
MAY ARISE FROM LOSS OF ANTICIPATED PROFITS OR
PRODUCTION, SPOILAGE OF MATERIALS,, INCREASED COST OF
OPERATION, OR OTHERWISE.
3
Description
The Paslode Angled Finish
nailer is a self-contained, fully
portable nailer that uses liquid hydrocarbon fuel to power a
unique linear drive internal combustion motor.
In order for you to fully understand the information contained
in this manual, you need a basic understanding of the
Paslode Angled Finish nailer. As you can see in the illustration
below, the Paslode Finish nailer is made up of three major
areas: handle, motor, and magazine.
As you examine the Paslode Angled Finish nailer, become
familiar with the three major areas and the various
components located in each of them.
The Handle contains the fuel cell, indicator light, and the
trigger.
The Motor contains the cover and filter, the motor housing,
the nose, and the work contacting element.
The Magazine contains the components to load and control
the fastener and the battery for the Paslode Angled Finish
nailer.
Specifications
Dimensions: Weight-with battery 4 lbs 14oz.
Height 11-1/2 inches
Length 10-3/4 inches
Magazine Angled
(use Paslode angled fasteners only.)
Cycle Rate: Intermittent Operation – 2 to 3 nails
per second
Continuous Operation – 500 nails
per hour
NOTE: Exceeding these cycle rates could cause the tool to
overheat, resulting in loss of performance or damage to tool
components.
By using the Paslode Angled Finish nailer at its
recommended cycle rate, you will be able to drive several
thousand nails in a typical workday.
Fasteners: 16 gauge, angled F-16 Series, Chisel Point
Magazine Capacity: 2 nail strips, or 100 fasteners
Battery : 6 volts DC - Provides enough energy to
drive approximately 4000 fasteners on a full
charge.
Fuel Cell: Liquid hydrocarbon - Provides enough fuel
to drive approximately 1200 fasteners.
An Overview of the Paslode Angled Finish Nailer
reversable
belt hook
Magazine
fuel cell compartment
cap
removable
cover & filter
no-mar tip
Handle (soft grip)
soft
touch
trigger
Motor
battery compartment
(opposite side)
battery indicator light
(opposite side)
follower
motor housing
nail count indicator
lockout
feature
adjustable
depth of drive
(opposite side)
quick clear
cover
4
Safety Instructions
The following safety instructions have been included in this
booklet to provide you with basic information necessary for
safe operation of the Paslode
Angled Finish Nailer. DO
NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU
HAVE READ AND UNDERSTAND ALL SAFETY
PRECAUTIONS AND MANUAL INSTRUCTIONS.
DANGER
The Paslode
Angled
Finish Nailer is an internal
combustion device. It
produces hot exhaust
gases that may ignite
flammable materials. This
tool must not be used in a
combustible environment
or in the presence of
combustible materials,
such as flammable
chemicals, adhesives,
gasoline, or solvents.
WARNING
Do not attempt to
operate this tool until
you have read and
understood all safety
precautions and manual
instructions. Failure to
follow all safety
precautions and
instructions may result in
a permanent loss of
vision, serious personal
or even fatal injury,
property damage and/or
tool damage.
WARNING
Do not expose the tool to
temperatures in excess of
120° F (49° C). Fuel and/
or the battery may burst,
releasing flammable gas.
WARNING
ALWAYS keep the
Paslode Angled Finish
Nailer, fuel cell, battery
and battery charger out
of the reach of children.
WARNING
This tool must be operated
only in a well-ventilated
environment, because the
tool exhausts carbon
monoxide similar to a gas
chainsaw or lawnmower.
Exposure to carbon
monoxide may cause
dizziness, nausea, or
unconsciousness.
5
Safety Instructions
WARNING
Always wear EYE and
EAR safety gear when
working with or in the
vicinity of the Paslode
Angled Finish Nailer.
7. NEVER OPERATE THE TOOL WITH THE WORK
CONTACTING ELEMENT REMOVED OR DISABLED.
This device helps reduce the possibility of accidental
fastener discharge by preventing the tool from operating
until it is completely against the work surface.
NEVER operate the tool if the work contacting element
is not working properly.
8. ALWAYS POINT THE TOOL AWAY FROM
YOURSELF AND OTHERS WHEN CLEARING
JAMS OR REMOVING FASTENERS.
Pull the follower slightly back and push the release
lever. Tip the tool nose up slightly and fasteners should
slide out of the rear of the magazine. If fasteners are
jammed, refer to the appropriate servicing section of
this manual.
9. NEVER OPERATE THE PASLODE
ANGLED FINISH
NAILER IF PARTS ARE LOOSE, DAMAGED OR
MISSING.
10. DO NOT DRIVE FASTENERS INTO KNOTS OR ON
TOP OF OTHER FASTENERS.
A fastener may ricochet and cause serious injury.
11. OPERATE THE TOOL ONLY ON THE WORKPIECE.
1. Eye protection must meet the requirements of ANSI
Standard Z87.1 and should have side shields for
increased protection.
2. NEVER ASSUME THE TOOL IS EMPTY.
Never point the tool at yourself or anyone else.
3. NEVER ENGAGE IN "HORSEPLAY" WITH THE TOOL.
The Paslode Angled Finish Nailer is not a toy – it is a
tool. Careless and improper use may result in a serious
accident.
4. NEVER CARRY THE TOOL WITH YOUR FINGER ON,
OR SQUEEZING, THE TRIGGER.
This practice may result in the accidental discharge of
a fastener.
5. NEVER OPERATE A MALFUNCTIONING TOOL.
Refer to the servicing or troubleshooting section of this
manual to correct the problem. If the problem cannot be
corrected, stop using the tool and report it to your
supervisor or Paslode
®
representative.
6. DO NOT LOAD FASTENERS WITH THE TRIGGER
AND/OR WORK CONTACTING ELEMENT PRESSED
IN.
A fastener may be accidentally discharged.
WARNING
The Paslode Angled
Finish Nailer should be
operated only when it is in
contact with the work
surface. When fastening
thin materials such as
plywood, be sure to
position the tool so that
the fastener is driven into
the underlying piece.
Loading...