Partlow 1166 1/16 DIN Data Sheet

Features

Control Types

PID with Pre-tune and RaPID fuzzy logic, or Manual Tuning. Heat or Heat/Cool, applications

Auto/Manual

Selectable from front panel, with bumpless transfer

Output Configuration

Up to 3 total. Max 2 for control (Heat & Cool), max 2 for Alarms, max 1 for retransmit PV or SP

Alarm 1 & 2 Types

Process high, process low, setpoint deviation and band

Human Interface

4 buttons, 10mm & 8mm high LED’s, plus run-hold, tune, event & profile/control status LED’s

PC Configuration

Off-line configuration & profile editing via config socket (comms option not required)

Profiles

Number of Programs

4, each with 16 free-form segments (Ramp/Dwell/End). Max segment length 99 hours 59 minutes

Delayed Start

Max 99 hours 59mins delay from initiation to program start

Guaranteed Soak

Holds program if PV is outside of specified hold band during dwell segments.

Program Cycles

1 to 9999 or infinite (continuously re-starts program at end)

Ramp Rate Definition

Either ramp rate, or time to final setpoint

Power Loss Recovery

Hot (continue profile from point of power fail) or Cold (end profile and return to controller mode)

Input

Thermocouple

J, K, R, S, T, B, L, & N.

RTD

3 Wire PT100, 50 per lead maximum (balanced)

DC Linear

0-20/4-20mA, 0-50/10-50mV, 0-5/1-5/0-10/2-10V. Scaleable -1999 to 9999, dec point available

Impedance

>100M for Thermocouple and mV ranges, 47K for V ranges and 4.7 for mA ranges

Accuracy

+/- 0.25% of input span +/- 1 LSD (T/C CJC better than 0.7°C)

Sampling

4 per second, 14 bit resolution approximately

Sensor Break Detection <2 secs (except zero based DC ranges), control O/P’s turn off, *high alarms activate

(*low for RTD inputs)

Outputs & Options

Control/Alarm/Event Relay

Contacts SPDT 2Amp resistive at 240V AC, >500,000 operations

DC for SSR

Drive capability >4.2V DC in 1K minimum (10V 500 version available)

DC Control/Retransmit

0-20/4-20mA into 500 max, 0-10/0-5V into 500 min. Accuracy, Control OP +/- 0.5%, Retransmit +/- 0.25%

Solid State (Triac)

0.01 to 1 Amp AC 20 to 280V, 47 to 63Hz

Remote Run-Hold

Volt free or TTL input (Hold = -0.6 to 0.8V or contact open, Run = 2 to 24V or contact close)

Communications

2 Wire RS485, 1200 to 9600 Baud, Modbus protocol

Operating and Environmental

Temperature & RH

0 to 55°C (-20 to 80°C storage), 20% to 95%RH non-condensing

Power Supply

100 to 240V 50/60Hz 7.5VA (optional 20 to 50V AC 7.5VA/22 to 65V DC 4W)

Front Panel Protection

IEC IP66 (Behind panel protection is IP20)

Approvals and Certification

CE, UL & Ulc

1166 1/16 DIN Profiler Controller

• Free-form programming

• Delayed start

• Guaranteed soak

• Power fail recovery

• Event/Profile active outputs

• Remote start

• Modbus comms

The 1166 is one of the most powerful profilers of its size available. It features our proven RaPID fuzzy logic control algorithm, for faster, more accurate control. Four programs can be held in memory.

Specification

Ref DS-1166-1-1207-ENUS

Dimensions

Connection Details

45 x 45mm

110mm

48mm

10mm (approx)

Field Reconfiguration

Input

45 x 45mm

+0.5 –0.0

Configurable to any type, no extra parts required

Output 1

Type is fixed as ordered. Either Relay/SSR (selectable), Triac or DC Linear (selectable

for mV, mA, Volts)

Output 2

Configurable as Cool O/P or Alarm, Event or Profile Active via plug-in Relay, Cool O/P or Alarm via plug-in SSR module, or Cool O/P only via Triac or DC Linear modules

Output 3

Configurable as Alarm, Event or Profile Active via plug-in Relay, Alarm via plug-in SSR module, or retransmit using DC Linear module

Option Slot

Configurable as RS485 comms or remote run-hold, via plug-in modules

Ref DS-1166-1-1207-ENUS

+ 1 hidden pages