Paradox NV35M Installation Manual

NV35M

Installation Manual v1.0

Outdoor/Indoor

Window and Sliding Door

Dual Detector with

Anti-Masking and

Pet Immunity

4. Attach the Main Unit to the back cover - ensure the locks snap closed.

NV35M-EI01

General Description

Thank you for choosing the NV35M for your professional protection needs.
The NV35M wired version will provide you the most advanced window and
sliding door protection either in Pet Immune or Sharp mode. If you have
any comments please write to us at Paradox.Com/products/feedback.
This guide describes how to install and program the NV35M.

Installing the NV35M

1. Remove the NV35M front cover - open the Captive screw.

Front cover

Captive screw

Figure 1 – Removing the

Front Cover

Figure 2 – Main Unit

1

23

Figure 5 – Attaching the Main Unit

5. Connect the wires to the terminal blocks according to the following
wiring assignment.

Table 1: Wiring Assignment

Terminal Connector Recommended Wiring Assignment

1 12V+

2 Minus (-)

3 Fault indication

4 Tamper indication

5 Common (Fault & Tamper)

6 Alarm indication

7 Common (Alarm)

6. Set the following Detector settings according to requirements.

Sensitivity Trimmer

2. Remove the Main Unit: open the two snap-lock mechanisms on each
side of the back cover attaching the Main Unit to the back cover as
displayed below. Then remove the Main Unit.

Figure 3 – Removing the Main Unit

3. Pull the wires from the control panel through the knockout holes and
mount the back cover onto the window frame or wall using screws.

Figure 4 – Mounting the Back Cover

Knockout
holes

Mounting
screw 1

Tamper
knockout
hole

Mounting
Tamper
screw 2

LED flashes green 1-3 times
according to the selected
level

Figure 6 – Detector Settings

The following table displays the Dip Switch settings.

Table 2: Dip Switch Settings

Dip Switch

Number

1 LED

2

Function Mode Description

ON: LED on (default)
OFF: LED off

PET Immunity/
SHARP Mode

ON: PET Immunity mode (default)
OFF: SHARP mode

7. Replace the front cover and close the Captive screw.

Warning: Do not obscure the detector's field of view.

Dip Switch

PARADOX.COM

Testing the NV35M

LED Display

Perform a Walk-Test to test successful installation: Walk slowly across the
far end of the detection range. Ensure detection.

Walk test mode lasts 5 minutes after the tamper screw is closed.

Beam Pattern

PET Mode

SHARP Mode

Top View

Feature LED Status Indicator

Tamper open Green: ON for 0.3 seconds every 30

seconds

PIR sensitivity level setting Green: Flashes 1-3 times according to

the selected level

Alarm detection Red: ON for 2 seconds

Booting/Tamper close Green/Red alternating flashes for 30

seconds

Anti-mask detection Orange: Flashes ON/OFF 3 times every

60 seconds

Technical Specifications

Specification Description

Infrared sensor type 2 Dual elements

Detection range • PET Immunity mode: 7.5m x 2m (25 x 7

ft)

• Sharp mode: 10 x 2m (33 x 7 ft)

Super Pet Immunity Pet size approximately 50cm

Anti- mask Active IR detection for blocking items 30cm

and sprayed liquid

Input voltage 10 to 15VDC

Current consumption Typical: 15mA

Maximum: 19.2mA

Compatibility EVO, Spectra and Magellan systems

Outdoor protection IP54

Operation temperature -35°c: +50°c

Relative humidity 95% non-condensing

Dimensions 12.3 x 6.1 x 4.3 cm (4.8 x 2.4 x 1.7 in.)

Certifications CE, EN50131-2-2 Grade 3, Class IV

Weight 100g / 0.2 lb

Notification

Changes or modifications to this equipment not expressly approved by the
party responsible for compliance (Paradox Security Systems Ltd.) could
void the user’s authority to operate the equipment.

Warranty

The Limited Warranty Statement found on the website www.paradox.com/
terms.

Your use of the Paradox product signifies your acceptance of these terms
and conditions.

Patents

The following US patents may apply 5,886,632 and 6,215,399, Other
Canadian and international patents may apply.

Printed in Canada 05/2015.

PARADOX.COM