ParaBody Serious Steel 894104 Assembly Manual

!

Serious Steel

894104 PEC DEC OPTION

Illl

I

ASSEMBLY INSTRUCTIONS

I

Part # 6820101

1

Revision:4/26/99

[ IMPORTANT NOTES’[

WELCOME TO THE WORLD OF SeriOUS ~e~!lt

Please no~e:

* Thank you for purchasing the Parabody 894104 PEC DEC OPTION. Please read these
instructions thoroughly and keep them for future reference. This product r~m,,;t be assembl~l on a

fiat, level surface to assure its proper function.

* We recommend cleaning your product (pads and frame) on a regular brads, using warm soapy

water. Touch-up paint can be purchased from your Parabody customer serape representative

at [phone].

There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:

1.

Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.

2. Do not allow minors or children to play on or around this equipment.

3. Exercise with care to avoid injury.

4.

If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at [phone].

5. Consult a physician before beginning any exercise program.

I Tools Required for Assembly I

*

3/4" wrench

* 9/16" wrench ~
* Ratchet with 3/4" and 9/16" sockets
*

Adjustable wrench

* Tape measure

[ Bolt Length Ruler [

NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSI])E OF THE HEAD OF THE BOLT.

BOLT LENGTH RULER:

BOLT LENGTH

1/2

I

1/2

I

1/2

I

1/2

I

1/2

I

1/2 l

6

2

I I I I

1

I I I I

I I I

I

KEY PART #

DESCRIPTION

1 6818103

BEARING HOUSING

2

6818403 PEC DEC ARM LEFT

3 6818503 PEC DEC ARM RIGHT

4

6818303 CENTER PULLEY BRACKET

5

6686802 PULLEY BRACKET

6 6597402

BACK PAD
7 6176201 4 X 12" ROLLER PAD
8 3116201

3-1/2" PULLEY

9 6492201 94-1/2" CABLE

10 6819001

134-3/4" CABLE

11 6405201 2" SQ END CAP

PARTS LIST

QTY

KE~ PART#
1 12 61407O1
1

13 6533501

1 14

3102933

1

15 3102922

1

16 3102918

1 17

3102501

2

18 3102801

5 19

3102502

1 20 3102801

1

21

6 22

DES ’,RIPTION

1 X 1" GUIDE

CABLE Pd~TAINING CLIP

3/8. 2" BOLT

3/8 X 2-3/4" BOLT

1/2 X 3-1/4" BOLT

3/8- V~/ASHER

3/8" LOCK NOT

1/2’ RASHER

1/2" LOCK NUT

3104901

3/4"FLPiNC~BEARING

3102804 1/2" LOW~EIGHTLOCK-NUT

FIGURE 1

STEP 1:
¯ Remove the lower CABLE from the UPRIGHT FRAME and PULLEY BLOCK and discard as shown in FIGLrRE 1.

¯

Remove eight 9/16" HOLE PLUGS from the UPRIGHT FRA~ME if applicable. See FIGURE 1.

QTY

2

4

5
2

2
6

5 "

2
2
4

2

FIGURE 2

STEP 2:

¯ Assemble t~vo 1 X 1" GLIDES (12) to the BEARING HOUSING (1) as sho~vn in FIGURE

¯ Insert t~vo 2" SQ. END CAPS (11) to the ends of the BEARING HOUSING (1) as shown in FIGURE

1/2 [ 1/2 [

1/2

[ 1/2

[

1/2 ~

5

4

1/2

I

6