PANJIT CP3010, CP301, CP306, CP304, CP302 Datasheet
CP300 THRU CP3010
Recongnized File #E111753FEATURES
MECHANICAL DATA
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTIC
S
CP300CP301CP302CP304CP306CP308CP301
0
Typical Junction capacitance per leg(Note 4)C
J
P
CP-
3
SINGLE-PHASE SILICON BRIDGE-P.C. MTG 2A, HEAT-SINK MTG 3A
VOLTA GE - 50 to 1000 Volts CURRENT - 3.0 Amperes
l
Surge overload rating—50 Amperes peak
l
Low forward voltage drop and reverse leakage
l
Small size, simple installation
l
Plastic package has Underwriter Laboratory
Flammability Classification 94V-O
l
Reliable low cost construction utilizing molded
plastic technique
Terminals: Leads solderable per MIL-STD-202,
Method 208
Weight: 0.08 ounce, 2.5 grams
At 25 ¢J ambient temperature unless otherwise noted; resistive or inductive load at 60Hz.
UNITS
Max Recurrent Peak Rev Voltage 50 100 200 400 600 800 1000 V
Max Bridge Input Voltage RMS 35 70 140 280 420 560 700 V
Max Average Rectified Output at TC=50¢J*
See Fig.2 at TA=25 ¢J**
Peak One Cycle Surge Overload Current 50 A
Max Forward Voltage Drop per element at
1.5A DC & 25¢J. See Fig.3
Max Rev Leakage at Rated DC Blocking
Voltage per element at 25
See Fig.4 at 100¢J
I2t Rating for fusing ( t<8.3ms) 15.0 A2Sec
Typical Thermal Resistance per leg(Note 2) R£KJA
(Note 3) R£KJL
Operating Temperature Range -55 TO +125 ¢J
Storage Temperature Range -55 TO +150 ¢J
NOTES:
1. Bolt down on heat-sink with silicon thermal compound between bridge and mounting surface for
maximum heat transfer with #6 screw.
2. Unit mounted on 4.0¡Ñ 4.0 ¡Ñ0.11” thick (10.5 ¡Ñ 10.5¡Ñ 0.3cm) AL. Plate.
3. Unit mounted on P.C.B at 0.375”(9.5mm) lead length with 0.5 ¡Ñ0.5” (12 ¡Ñ 12mm) copper pads.
¢J
3.0
2.0
1.0 V
10.0
1.0
21.0
12.0
8.0
¢J
£g
mA
A
A
F
/W
4. Measured at 1 MHz and applied reverse voltage of 4.0 Volts.
RATING AND CHARACTERISTIC CURVES
NUMBER OF CYCLES AT 60h
z
C
AMBIENT TEMPERATURE,
¢J
TYPICAL
INSTANTANEOUS FWD VOLTAGE, VOLT
S
TA = 10
0
PERCENT OF PEAK REVERSE VOLTAG
E
IN
CP300 THRU CP3010
50
40
5
FORWARD SURGE CURRENT,
AMPERES pk (HALF SINE-WAVE)
30
20
10
0
2
4
6 10
20 40 60 100
60Hz RESISTIVE OR
4
INDUCTIVE LOAD HEAT SINK
3
2
1
OUTPUT CURRENT AMPERES
P.C. BOARD
0
0 50 100 150
MOUNTING T
2.0" sq × 0.62 thick
Copper Plate
Fig. 1- NON-RECURRENT SURGE RATING Fig. 2- DERATING CURVE FOR OUTPUT RECTIFIED
CURRENT
5
4
3
2
1
.9
.8
.7
.5
.3
DISTRIBUTION
.2
.1
.07
.05
.03
.02
STANTANEOUS FWD CURRENT AMPERES
.01
0 0.2 0.4 0.6 0.8
MEDIAN
1.0 1.2 1.4
Fig. 3- T YPICAL FORWARD CHARACTERISTICS(25
¢J)
10
20 40
¢J
TA = 25¢J
60 80
100 120 140
1.0
.1
MICROAMPERES
INSTANTANEOUS REVERSE CURRENT,
.01
0
Fig. 4- TYPICAL REVERSE CHARACTERISTICS
Loading...