Installation Manual
Additional Digital Cordless Handset
Thank you for purchasing a Panasonic product.
This unit is an additional handset compatible with the following series of
Panasonic Digital Cordless Phone:
- KX-TGC350/KX-TGC360
(The corresponding models are subject to change without notice.)
You must register this handset with your base unit before it can be used. This
installation manual describes only the steps needed to register and begin using
the handset. Please read the base unit’s operating instructions for further details.
Please read this installation manual before using the unit and save it for future
reference.
For assistance, visit our Web site: http://shop.panasonic.com/support
for customers in the U.S.A.
Model No. KX-TGCA35
KX-TGHA20
Printed in Malaysia
PNQX7767ZA
PT1115MG0
Accessory information
Supplied accessories
Accessory item/Order number Quantity
1
Rechargeable batteries/HHR-4DPA 2
1
*
Note:
R Please read the base unit’s operating instructions for additional/replacement
accessories.
Setting up
Connections/Wall mounting
Connect the AC adaptor to the power outlet.
Drive the screws (1) (not supplied) into the wall, if necessary.
Installation
Charger/PNLC1073ZB
1
Handset cover
1 The handset cover comes attached to the handset.
*
/PNYNTGCA35BR
For assistance, please visit http://shop.panasonic.com/support
Note:
R The AC
adaptor must remain connected at all times. (It is normal for the adaptor
to feel warm during use.)
R Make sure that the wall and the fixing method are strong enough to support the
weight of the unit.
Battery installation/Battery charging
Import
ant:
R Use the supplied rechargeable batteries. For replacement, we recommend using
the Panasonic rechargeable batteries noted on page 2.
R USE ONLY rechargeable Ni-MH batteries AAA (R03) size (
).
R Do NOT
use Alkaline/Manganese/Ni-Cd batteries.
R Confirm correct polarities (
, ).
Charge
for about 7 hours.
R Confirm “Charging” is displayed (
).
R When t
he batteries are fully charged, “Fully charged” is displayed.
Note:
R If the batteries are fully charged, but the operating time seems to be shorter,
clean the battery ends (
, ) and the charge contacts with a dry cloth and
charg
e
again.
Registering a handset to a base unit
1 Base unit:
Press and hold M N for about 5 seconds. R If all registered
handsets start ringing, press M N
again to stop, then repeat this step.
For assistance, please visit http://shop.panasonic.com/support
2 Handset:
Pl
ace the handset on the base unit or charger, then wait until a long beep
sounds and
is displayed.
Not
e:
R If an error tone sounds, or if
is displayed, register the handset according to
the
base unit’s operating instructions.
Display language
1 MMEN
UN (right soft key) #110
2 MbN: Select the desired setting. a MSAVEN a MOFFN
For your safety
To
prevent severe injury and loss of life/property, read this section carefully before
using the product to ensure proper and safe operation of your product.
WARNING
Power connection
R Completely insert the AC adaptor/power plug into the power outlet. Failure to do
so may cause electric shock and/or excessive heat resulting in a fire.
R Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it
from the power outlet, then wiping with a dry cloth. Accumulated dust may cause
an insulation defect from moisture, etc. resulting in a fire.
R Unplug the product from power outlets if it emits smoke, an abnormal smell, or
Installation
R To prevent the risk of fire or electrical shock, do not expose the product to rain
or any type of moisture.
R Do not place or use this product near automatically controlled devices such as
automatic doors and fire alarms. Radio waves emitted from this product may
cause such devices to malfunction resulting in an accident.
4
makes an unusual noise. These conditions can cause fire or electric shock.
Confirm that smoke has stopped emitting and contact us at
http://shop.panasonic.com/support
For assistance, please visit http://shop.panasonic.com/support