Panasonic WV-X4170, WV-X4171, WV-S4150 Installation Guide
PGQX2201XA avs1117-2127 Printed in China
Preparations
Installation method
Description of
installation method
Mount the camera on the two-gang junction box using the attachment plate (accessory).
【Type 1】
Directly mount the camera onto the ceiling or wall using the attachment plate (when wiring can be installed in the ceiling or wall).
【Type 2】
When mounting the camera on an insuffi ciently strong ceiling using
the WV-Q105A ceiling mount brackets
(approximately 150 g {0.33 lbs}).
Refer to the Instruction
Manual provided with the
WV-Q105A *1.
When mounting the camera on ceiling using the
mount bracket
(locally procured)
*2
.
Refer to the Instruction Manual provided with the mount
bracket (locally procured)
*1
*1 Make sure that the installed mount bracket can support more than 5 times of the total weight of
the camera, brackets and anchor bolt itself.
*2 Connect the safety wire to the camera referring to “Attach the safety wire (accessory)”
mentioned at right, and secure the safety wire on the ceiling using the washer (accessory), spring
washer (accessory), and a fixing screw (locally procured).
External I/O terminal plug
Power cable plug
Step 2 Fixing the attachment plate
*There are 2 methods to install the camera to a ceiling or wall.
【
Type 1】Mount the camera on the two-gang junction box using the attach-
ment plate
.
Network Camera
Model No. WV-X4171 / WV-X4170
WV-S4150
Installation Guide
Included Installation Instructions
Important safety instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7)
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8)
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Only use attachments/accessories specified by the manufacturer.
10) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
11) Unplug this apparatus during lightning storms or when unused for long periods of time.
12) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
Troubleshooting
Open Source Software
This product contains open source software licensed under GPL (GNU General Public License),
LGPL (GNU Lesser General Public License), etc.
Customers can duplicate, distribute and modify the source code of the software under license of
GPL and/or LGPL.
Refer to the “readme.txt” file on the provided CD-ROM for further information about open source
software licenses and the source code.
Please note that Panasonic shall not respond to any inquiries regarding the contents of the source
code.
The model number and serial number of this
product may be found on the surface of the unit.
You should note the model number and serial
number of this unit in the space provided and
retain this book as a permanent record of your
purchase to aid identification in the event of
theft.
Model No.
Serial No.
NOTE: This equipment has been tested and found
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Caution: To assure continued compliance,
(example - use only shielded interface cables
when connecting to computer or peripheral devices). Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate this
equipment.
For U.S.A.
For U.S.A.
CAN ICES-3(A)/NMB-3(A)
For Canada
WARNING:
• To prevent injury, this apparatus must be securely attached to the wall/ceiling in accordance with
the installation instructions.
• To prevent fire or electric shock hazard, do not
expose this apparatus to rain or moisture.
• The apparatus should not be exposed to dripping or splashing.
• All work related to the installation of this product
should be made by qualified service personnel
or system installers.
• The installation shall be carried out in accordance with all applicable installation rules.
• The connections should comply with local electrical code.
• Batteries (battery pack or batteries installed)
shall not be exposed to excessive heat such as
sunlight, fire or the like.
CAUTION:
• Any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
• The network camera is only intended for a connection to an ethernet or PoE network without
routing to the outside plant.
Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries must not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them
to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment.
For more information about collection and recycling, please contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
Note for the battery symbol (bottom symbol)
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
About the user manuals
Product documentation is composed of the following documents.
• Installation Guide (this document): Explains installation, mounting, cable connections, and adjusting the
fi eld of view. This manual uses the WV-S4150 as an example in the explanations.
• Important Information (included in the CD-ROM):
Provides basic information about the product.
• Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to
operate this camera.
Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.
When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the Adobe web site
and install it.
The external appearance and other parts shown in this manual may differ from the actual product within the
scope that will not interfere with normal use due to improvement of the product.
Standard accessories
Installation Guide (this document) ........................1 set
IMPORTANT SAFETY INSTRUCTIONS ............... 1 pc.
Warranty card*1 ...................................................1 set
CD-ROM*2 .......................................................... 1 pc.
Code label*3........................................................ 1 pc.
*1 This product comes with several types of warranties. Each warranty is only applicable to the products pur-
chased in the regions indicated on the relevant warranty.
*2 The CD-ROM contains the operating instructions and different kinds of tool software programs.
*3 This label may be required for network management. Use caution not to lose this label.
The following parts are used during installation procedures.
Attachment plate ................................................ 1 pc.
Template A (for the attachment plate)
......................1 sheet
Audio cable
.................... 1 pc.
Power cable plug*
4
......... 1 pc.
External I/O terminal plug*
4
.. 1 pc.
Cable tie
.. 2 pcs. (incl. 1 spare)
Safety wire lug
................ 1 pc.
Safety wire
....................... 1 pc.
Washer
........................... 1 pc.
Spring washer
................ 1 pc.
*4
The external I/O terminal plug and power cable plug are attached to the camera.
Prepare the required parts for each installation method before starting the installation.
IMPORTANT:
Procure 4 screws (M4) to secure the attachment plate (accessory) to a ceiling or a wall.
The minimum required pull-out capacity of a single screw or anchor bolt is 196 N {44 lbf} or
more when mounting with the installation method 【Type 1】 or 【Type 2】 described in the
table below.
Select screws according to the material of the location that the camera will be mounted to.
In this case, wood screws and nails should not be used.
If the mounting location such as plaster board is too weak to support the total weight, the
area shall be sufficiently reinforced.
Installation
Step1
Insert an SD memory
card.
Step2
Fixing the attachment
plate
Step3
Making connections
⇨
⇨
Step5
Configure the network
settings
⇨
Step4
Mount the camera
⇨
Step6
Make fi ne adjustment to
the image direction
⇨
Remove the camera using the reverse order of the installation procedures.
The installation tasks are explained using 6 steps.
【
Type 2】Directly mount the camera onto the ceiling or wall using the attach-
ment plate.
46 mm {1-13/16 inches}
83.5 mm {3-9/32 inches}
Two-gang junction box
Attachment plate (accessory)
Fixing screws for attachment
plate: 4 pcs. (M4, locally procured)
When installing the camera directly on the ceiling or
wall with cables exposed, cut out a portion of the
enclosure to open a cable access hole.
IMPORTANT:
To prevent injuries and protect the cables, finish the
side cable access hole with a file to avoid sharp
edges.
Side cable access hole
Before requesting service, refer to the Important Information (included in the CD-ROM) and
“Troubleshooting” in the Operating Instructions (included in the CD-ROM) and confirm the
trouble.
: Direct current symbol
【
Common
】
Before attempting to connect or operate this product, please read these instructions carefully and
save this manual for future use.
For information about the basic description of this product, refer to the Important Information on
the provided CD-ROM. For information about how to perform the settings and how to operate the
camera, refer to the Operating Instructions on the provided CD-ROM.
The model number is abbreviated in some descriptions in this manual.
© Panasonic Corporation 2017
For U.S. and Canada:
Panasonic System Communications
Company of North America,
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark,NJ 07102-5490
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
For Europe and other countries:
Panasonic Corporation
http://www.panasonic.com
Panasonic Corporation
Osaka, Japan
Authorised Representative in EU:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Audio cable
Other items that are needed (not included)
Attach the safety wire (accessory)
Processing of side cable access hole
Attach the attachment plate (accessory) so that the “TOP” mark (see the illustration at left in
【
Type 2】) faces toward the opposite side of the attachment
face (camera installation side).
When this product is installed on a wall, attach the attachment plate
(accessory) with the “TOP” mark facing upward.
Fixing screws for attachment plate: 4 pcs.
(M4, locally procured)
Attachment plate (accessory)
83.5 mm
{3-9/32 inches}
46 mm
{1-13/16 inches}
ø30 mm {ø1-3/16 inch}
TOP mark
Align the front direction of the template A (accessory) with the direction to be attached
(upper direction of the screen), bore holes for screws or anchors on the ceiling or wall,
and a hole for wiring (ø30 mm {ø1-3/16 inch}) as occasion demands. Then, fix the
attachment plate.
Step1 Insert an SD memory card
When using an SD memory card, go through the following procedure before installing the camera.
When removing an SD memory card, reverse the procedure.
Refer to the Important Information on the provided CD-ROM for further information about the SD
memory card settings.
【1】
Loosen the SD slot cover fixing screw, then insert a slotted head driver or other tool
into the notched area on the SD slot cover to remove SD slot cover.
*Do not use excessive force when removing SD slot cover. Failure to observe this may damage
the SD slot cover.
Notched area
SD slot cover
SD slot cover fixing screw
【2】
Insert an SD memory card into the SD memory card slot straight to the
end, and confirm a click sound is heard. (direct the label face of the SD
memory card toward the lens side of the camera)
After a click sound is heard, release your finger from the SD memory card and confirm the rear
end of the card does not project from the higher parts of the SD guide rib.
【3】Close the SD slot cover, and tighten the SD slot cover fixing screw to secure the
cover.
(Recommended tightening torque: 0.39 N·m {0.29 lbf·ft})
Higher parts of SD guide rib
SD slot cover
fixing screw
SD slot cover
SD memory
card slot
SD memory card
(label face)
The following are descriptions of safety wire (accessory) attachment when mounting the camera
on the mounting bracket (locally procured).
【2】Engage the safety wire (accessory) with the wire engaging hole.
Wire lug fi xing screw
Fixing screw hole
Safety wire lug (accessory)
Safety wire lug (accessory)
Wire engaging hole
Safety wire (accessory)
【1】Remove the wire lug fixing screw from the bottom of this product, and attach the
safety wire lug (accessory) to the camera with the screw.
IMPORTANT:
Attach the safety wire lug (accessory) in
the direction that is shown in the enlarged
illustration at right.
Use the wire lug fixing screw to attach the
safety wire lug (accessory). When using
different length screws, it may damage
the camera or cause the camera to fall.
(Recommended tightening torque:
0.39 N·m {0.29 lbf·ft})
Rear end of SD memory card
* Camera is not shown in these illustrations.
Center of the camera
Enclosure
WV-X4171 WV-S4150
The following notations are used when describing the functions limited for specified models.
The functions without the notations are supported by all models.
:The functions with this notation are available when using the model WV-X4171.
:The functions with this notation are available when using the model WV-X4170.
:The functions with this notation are available when using the model WV-S4150.
About notations
X4171 S4150
X4171
S4150
Side cable access hole
S3125A
X4171
X4170
S4150
X4171 S4150
X4171
X4171 S4150
S4150
X4171
X4171 S4150
S4150
4
3
2
1
X4171
X4171 S4150
S4150
X4171 S4150
X4171 S4150
X4171 S4150
X4171 S4150
X4171 S4150
Step 4 Mount the camera
【1】Align the OPEN mark on the side of
enclosure with the tab of the attachment
plate, insert 3 attachment mounting
screws into the attachment plate, and
rotate the camera by approximately 20°.
The camera is temporarily secured.
(align the LOCK mark center, “I”, with the
tab of the attachment plate)
Step 3 Making connections
Note:
The audio output can be switched to the monitor output. Refer to the "Operating
Instructions" on the provided CD-ROM for descriptions of how to switch the output.
Step 5 Configure the network settings
Configure the setting of the camera after temporarily invalidating the firewall software. Once the
camera configuration is completed, return to the original state.
Contact the network administrator or your Internet service provider for information about configuring
the settings of the network.
【2】Click the [Run] button next to [IP Setting Software].
⇒
[Panasonic IP Setting] screen will be displayed.
The MAC Address / IP address of the detected camera will be displayed.
【1】Insert the provided CD-ROM into theCD-ROM drive of your PC.
The License Agreement will be displayed. Read the Agreement and choose “I accept the term in
the license agreement”, and click [OK].
⇒The launcher window will be displayed.
Note:
If the launcher window is not displayed,
double click the “CDLauncher.exe” file
on the CD-ROM.
Refer to “Using the CD-ROM” in the
Operating Instructions on the provided
CD-ROM for further information about
CDLauncher
Note:
For more information on the following content, refer to the Operating Instructions.
Please set [Time & date] on the [Basic] screen of “Setup” before using the camera.
It is impossible to display H.265 (or H.264) or MJPEG images, receive/transmit audio
, display logs, and use full-screen display when the viewer software
“Network Camera View 4S” is not installed on the PC.
Depending on the environment of your PC, it may take time for images to be displayed.
At the time of purchase, the audio input and output are set to “Off”.If needed, change the
setting on the “Audio” screen in “Setup”.
Due to security enhancements in “IP Setting Software”, “Network settings” cannot be
changed when around 20 minutes have passed after turning on the power of the camera to
be configured. (When the effective period is set to “20 min” in the “Easy IP Setup
accommodate period”.) However, settings can be changed after 20 minutes for cameras in
the initial set mode.
If images are not displayed, set the Web browser to compatibility view. For details on how to
configure, refer to our website (https://security.panasonic.com/support/info/)
【3】Select the camera you want to configure (A), and click [Network Settings]
(B) to chance the network settings. Then, click [Access Camera] (C).
Note:
Select the camera with same MAC address as the MAC address printed on the camera that you
want to configure.
A
B
【4】When the administrator registration window is displayed, enter “User
name”,“Password” and “Retype password” by following the instructions
displayed on the screen, and then click the [Set] button.
IMPORTANT:
When the camera is used over the Internet, setting user authentication to “Off” may lead
to unintended access by a third party. Please leave user authentication set to “On”.
【5】When live images from the camera are displayed, the network connection
is complete.
■
Refer to the Important Information on the provided CD-ROM for details about each cable.
As necessary, use a cable tie (accessory) to tie the cables together.
【2】
Connect an Ethernet cable (category 5e or bet-
ter, straight) to the network connector.
【3】
If needed, connect a microphone or the line out of an external device to the
audio input connector.
IMPORTANT:
Turn off each system’s power supply (PoE hub or device to supply power to the camera) before
making a connection.
T
he 12 V DC power supply shall be insulated from the commercial AC power.
Please keep your user name and password in a safe place free from public view to ensure
security. After completing the registration, the camera will automatically be re-connected and
the authentication window will be displayed. Enter the registered user name and password.
The default setting of user
authentication is “On”. For
further information, refer
to the “Preface” section in
the Operating
Instructions.
【1】
When connecting an AC adaptor or an external power supply, use the
power cable plug (accessory) to connect it to the camera.
Caution:
A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO
THE EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.
ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED
POWER SOURCE (IEC/EN/UL/CSA 60950-1).
① Strip 3 mm to 7 mm {1/8 inches to 9/32 inches} from the
end of the wire, twist the stripped part of the wire sufficiently to avoid short circuit.
When connecting an external power supply to the camera,
use the 16 AWG to 24 AWG single-wired or stranded wired
cables.
②Loosen the screw of the power cable plug (accessory),
connect the output cable to the power cable plug
③Tighten the screw of the power cable plug
(accessory)
.
(Recommended tightening torque: 0.34 N·m {0.25 lbf·ft})
④Connect the power cable plug to the camera.
【5】
If needed, connect the alarm input/output cables to the EXT I/O terminal plug
(accessory).
Note:
Do not connect 2 wires or more directly to a terminal. When it is necessary to connect 2 or
more wires, use a splitter.
Check whether the stripped part of the wire is not exposed and is securely connected.
The default of EXT I/O terminals is "Off". Refer to the Operating Instructions on the provid-
ed CD-ROM for further information about the EXT I/O terminal settings.
Connect an external device to the external I/O terminal plug (accessory) and fit it into the camera.
①
When connecting an external device, remove 8 mm - 9 mm
{5/16
inches -
11/32
inches
}
of the
outer jacket of the cable and twist the cable core to prevent the short circuit first.
Specification of cable (wire): 20 AWG - 26 AWG, Single core, twisted
②
Push down the button of the desired terminal on the external I/O terminal plug with a ballpoint
pen, and release the button when the cable of the external device is fully inserted into the terminal hole.
③Connect the external I/O terminal plug to the camera.
【4】
If needed, connect a powered speaker to the audio output connector.
C
Step 6 Make fine adjustment to the image direction
Cable connection to the camera
Preparation for cable connection
Power
cable
plug
External I/O
terminal
plug
【１】Remove the power cable plug (accessory) and the external I/O terminal plug
(accessory) attached to the camera.
【2】
If needed, connect the audio cable (accessory) to the audio cable connector.
*When disconnecting the audio cable (accessory), pull out the audio cable (accessory) while
holding down the hook of the connector.
Hook of the
connector
Audio cable
connector
Audio cable
【5】External I/O terminal
【4】Audio output
connector (black)*
【3】Audio input
connector (white)*
【2】Network connector (RJ45)
*Make sure to use the stereo mini plug.
【1】12 V DC power supply terminal
Note:
Since the connector storage section does not
have a sufficient space, use a LAN cable that
does not exceed the sizes described in the illustrations.
9 mm
{11/32 inches}
13 mm
{1/2 inches}
Straight section
30 mm
{1-3/16 inches}
Example of Ethernet
cable connector
External I/O terminal plug
GND
ALARM IN3 (Alarm input 3/ AUX output)
ALARM IN2 (Alarm input 2/ Alarm output)
ALARM IN1 (Alarm input 1/ Auto time adjustment input)
Button
Tab of the
attachment plate
Attachment
mounting screws
OPEN mark
LOCK mark
Attachment plate
(accessory)
Note:
The image direction can be fi nely adjusted after
completion of the installation. Refer to “Step 6
Make fi ne adjustment to the image direc-
tion” for further information on adjustment.
【2】
Secure the camera.
IMPORTANT:
Be sure to tighten the camera fixing screw.
Failure to observe this may cause camera trouble
due to camera falling.
(Recommended tightening torque: 0.78N·m
{0.58 lbf·ft})
① Use a slotted head screwdriver to open the camera
fixing
screw cover.
②Secure the camera by tightening the camera fixing
screw.
③
Close the camera fixing screw cover.
Camera fixing
screw
cover
Camera fixing
screw
r
【3】Remove the protection fi lm from the lens.
【4】Turn on power for the camera.
See the captured image on a PC, and
follow the procedure described below for
fine adjustment of the upper direction of
the screen (camera direction).
For camera fixation, three points are
available considering “I” of the LOCK
mark as 0°; 0° (center), +5° (rightward),
and -5° (leftward).
Camera fixing
screw
cover
Camera fixing
screw
【1】
Use a slotted head screwdriver to
open the camera fi xing screw cover,
and then use a cross slot screwdriver
to loosen the camera fi xing screw.
【2】Move the LOCK position of
the camera clockwise or
counterclockwise to finely adjust
the image direction while seeing
the captured image on a PC.
【3】
Secure the camera by tightening
the camera fi xing screw, and then
close the camera fi xing screw
cover.
Camera fixing
screw
r
IMPORTANT:
Be sure to tighten the camera fixing
screw. Failure to observe this may cause
camera trouble due to camera falling.
(Recommended tightening torque:
0.78N·m {0.58 lbf·ft})
IMPORTANT:
Turning the camera counterclockwise
too much removes the camera from the
attachment plate. Be careful not to do
so.
IMPORTANT:
Loosening the camera fixing screw allows
the camera to be in the temporary fixed
state.
Upper direction of screen
Enclosure
40 mm
{1-9/16 inches}
Note:
The mic input is set to "Internal (built-in mic)" in the default settings of the camera. If you want to change the
mic input setting to "External(audio cable)", refer to the Operating Instructions on the provided CD-ROM.
X4171 S4150
X4171
X4171 S4150
S4150
X4171 S4150
4
3
2
1
X4171 S4150
X4171 S4150
X4171 S4150
X4171
power cable
plug (accessory)
S4150
X4171 S4150
X4171 S4150
(12 V DC)
(GND)
X4171 S4150
X4171 S4150
Loading...