Panasonic WV-PB5504AE Instructions Manual

Pin No. Designation

-1-

Video Output Board

WV-PB5504AE

Before attempting to connect or operate this product, please read these instructions completely

PREFACE

The WV-PB5504AE Video Output Board is provided for expanding the video output capability of the
Matrix Switcher.

APPEARANCE

1. Alarm Output/Reset Output Connector (ALARM OUT/RESET OUT)
External Timing Input Connector (EXT TIMING IN)
Recover Input Connector (RECOVER IN)

ALARM OUT: When the Matrix Switcher receives an alarm from the WV-PB5564E Alarm Board

or camera site receivers WV-RC100, WV-RC150 or WV-RC170, the alarm output signal is
provided at this connector for the Time Lapse VTR. The active pin number of the alarm out­put depends on the alarm mode set by the on-screen programme (Mode-1, Mode-2,
Mode-3).

RESET OUT: When the Matrix Switcher resets the activated alarm, the alarm reset output sig-

nal, either Open Collector or pulse, is provided at this connector for the Time Lapse VTR.

EXT TIMING IN: The camera switching interval (Sequential Dwell Time) can be synchronized

with the lapse mode set in the Time Lapse VTR.
EXT. TIMING IN 1 controls Monitor 1 output, EXT. TIMING IN 2 controls Monitor 2 output, etc.
Supply the camera switching pulse from the Time Lapse VTR to this connector. Minimum
duration for camera switching pulse needs to be more than one (1) second.

RECOVER IN: This connector accepts the alarm recover signal from the Time Lapse VTR.

When handling this board, hold only by circuit board edges. Otherwise components on the
board may be damaged by static electricity.

Caution

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

ALARM OUT 1
RESET OUT 1
RECOVER IN 1
Ground
EXT TIMING IN 1
Ground
ALARM OUT 2
RESET OUT 2
RECOVER IN 2
Ground
EXT TIMING IN 2
(+5V DC)
ALARM OUT 3
RESET OUT 3
RECOVER IN 3
Ground
EXT TIMING IN 3
Ground
ALARM OUT 4
RESET OUT 4
RECOVER IN 4
Ground
EXT TIMING IN 4
Ground
Ground

OUT

IN

OUT

IN

OUT

IN

OUT

IN

MONITOR

ALARM OUT
RESET OUT
EXT TIMING IN
RECOVER IN

OUTPUT

1

2

3

4

q

w

25

13

24
23
22
21
20
19
18
17
16
15
14

12
11

10

9
8
7

6
5
4
3
2
1

BOARD

NO.

-2-

BOARD SETTING

Before installing this board, the following settings should be made by qualified service personnel or system installers.

1. Set switches (SW1) on the board to meet the monitor output number as shown in the following table.
Initially, monitor 1-4 is selected at the factory.

1234

OFF

SW1

SW4
SW5

SW3

SW2

12

OFF

SW6

SW100

SW150

SW200

SW250

2. Monitor Input/Output Connector (MONITOR IN/OUT)

OUT: The video signal selected by the Matrix Switcher is provided at this connector for the video monitor.
IN: This connector is used for video input from a VTR or system expansion to 128 camera input.

1234

OFF

1234

OFF

1234

OFF

1234

OFF

1234

OFF

1234

OFF

1234

OFF

1234

OFF

1

2

3

4

5

6

7

8

1-4

5-8

9-12

13-16

1-4

5-8

9-12

13-16

MONITOR

OUT NO.

SW1 SETTING

Be careful when setting these switches as the swtches are not physically
located on the board in numerical order. Switch location from the top of the
board, going downward, is: SW4 (reset out 3), SW5 (reset out 4), SW3
(reset out 2) and SW2 (reset out 1).

2. Set switches (SW2/SW3/SW4/SW5) on the board to choose the alarm
reset output signal as either Open Collector (OPEN C.) or Pulse (VTR).

Open Collector (OPEN C.): 16VDC 100mA max.
Pulse (VTR): +5VDC approx. 500 msec.

Initially, VTR positions are selected at the factory.

CH1

OPEN C

VTR

Note