Panasonic WV-CP474H User Manual
1. The following functions are built in.
(1) Auto Light Control (ALC)/Electronic Light Control (ELC)
(2) The SUPER-D2 function eliminates interference by strong background lighting
which makes the camera picture dark, such as a spotlight.
Dynamic range of 46 dB.
(3) Internal Line-locked Multiplex Vertical (VD2) Sync.
(4) Auto/Manual White Balance Function
(5) Electronic Shutter Function
2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off)
3. Minimum Illumination of 0.8 lx (0.08 foot-candle) at color mode, 0.1 lx (0.01 foot-candle)
at black and white mode with F1.4 lens.
4. 480 lines of horizontal resolution
5. High quality picture:
(a) 2H type vertical enhancer for greater picture sharpness
(b) Chroma averaging circuit for better color signal-to-noise ratio
(c) Minimum of aliasing on fine objects
(d) Expanded dynamic range by use of knee circuit
(e) Highlight aperture correction for greater picture detail of bright objects
6. Ability to shoot indoor scenes with fixed iris lens by use of Electronic Light Control (ELC)
function.
7. Selectable electronic sensitivity enhancing modes including AUTO, MANUAL and OFF
8. Built-in Digital Motion Detector
9. Auto black-and-white mode enables the camera to switch between color and blackand-white picture in response to light input.
FEATURES
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws or covers.
There are no user-serviceable parts inside. Ask a qualified service personnel for servicing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged
by improper handling or storage.
3. The installation should be made by qualified service personnel or system
installers.
4. Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty. When the dirt is hard to remove, use a
mild detergent and wipe gently. Then wipe off the remaining detergent with a dry cloth.
5. Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton
tipped applicator and ethanol.
6. Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether the camera is in use or not, never
aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may
be caused.
7. Do not operate the camera beyond the specified temperature, humidity or power
source ratings.
Use the camera at temperatures within –10 °C to +50 °C (14 °F - 122 °F), and humidity
below 90 %. The input power source is 24 V.
8. Avoid do connections during a lightning storm.
Otherwise, electric shock may be caused.
PRECAUTIONS
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
The exclamation point within
an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing)
instructions in the literature
accompanying the appliance.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence
of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
The serial number of this product may be found
on the top of the unit.
You should note the serial number of this unit
in the space provided and retain this instruction
as a permanent record of your purchase to aid
identification in the event of theft.
Model No. WV-CP474H
Serial No.
SA 1966
SA 1965
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
q Auto Iris Lens Connector
Connects the auto iris lens with a 4-pin male connector supplied as a standard accessory (Part No. YFE4191J100).
w Flange-back Adjusting Ring & Screw
Adjusts the back focal length and picture focus.
e Lens (Option)
r Camera Mounting Screw Hole
Mounts the camera onto a mounting bracket.
t Down Button (D)
Moves the cursor downward and selects items in the CAM SET UP menu.
y Left Button (L)
Moves the cursor to the left, selects the mode and adjusts some levels.
u Up Button (U)
Moves the cursor upward and selects items in the CAM SET UP menu.
i Right Button (R)
Moves the cursor to the right, selects the mode and adjusts some levels.
o Set Button (SET)
Activates an item selected in the CAM SET UP menu.
!0 Video Output Cable with BNC Connector
Connects the VIDEO IN connector of the monitor.
!1 Power Cable
!2 Alarm Output Terminal (ALARM OUT/GND)
Connects to the alarm input connector (terminal) of an external device. When the camera detects motion, the alarm output signal is supplied to the connected external device
(Open collector output: 16 V DC, 100 mA max).
!3 Day/Night Input Terminal (DAY/NIGHT IN/GND)
This terminal is used for connecting the camera to an external day/night detecting sensor.
N1002-0 3TR001320AAA Printed in Japan
N 19
Panasonic's WV-CP474H series color digital camera introduces a new level of high picture
quality and high resolution through the use of a 1/3-inch interline transfer CCD image sensor
having 771 horizontal pixels (picture elements), and digital signal processing LSIs. This
model offers cutting-edge technology for advanced video surveillance.
PREF ACE
Caution:
To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for
the AC 24 V Input Cable.
Slide the panel to the left until it locks.
Color CCTV Camera
Operating Instructions
(Lens: Option)
WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SER-
VICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
NOTE: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference in
which case the user will be required to correct
the interference at his own expense.
FCC Caution: To assure continued compliance, (example - use only shielded interface
cables when connecting to computer or
peripheral devices). Any changes or modifications not expressly approved by the party
responsible for compliance could void the
user’s authority to operate this equipment.
For U.S.A
Model No.
WV-CP474H
qwe
r
!0
!1
Color CCTV Camera
Model No. WV-CP474H
POWER 24V~60Hz 4.3W
VIDEO OUT 1V[p-p] 75Ω
Monufochured by Matsushita
Communication industrial
Co.Ltd. Yokohama Japan
Made in Japan
FOR COMMERDAL USE ONLY
GND DUT
Day /
Night
IN
!3
uoy
U
LR
SET
D
ALARM
GND
POWER
!2
i
t
Mounting the Lens
Note: Before you mount the lens, loosen the screw on the side of the camera, and rotate the
ring clockwise until it stops.
If the ring is not at the end, the inner glass or CCD image sensor may be damaged.
1. Attach the supplied C-mount
adapter when using a C-mount
lens.
2. Jump to step 3 if the lens has focus
adjusting mechanism. Loosen the
flange-back screw, and rotate the
adjusting ring down until it stops on
the side of the camera.
3. Mount the lens.
4. Connect the lens cable to the auto
iris connector on the side of the camera.
Flange-back Adjustment
The adjustment is required only when a lens without focus-adjusting mechanism is mounted,
or when a lens with adjusting mechanism is mounted and focus that is more accurate is
needed.
1. Loosen the flange-back fixing screw on the flange-back adjusting ring.
2. Turn the flange-back adjusting ring to obtain a focused point while watching the monitor
screen.
3. Tighten the flange-back fixing screw on the flange-back adjusting ring.
Caution: Tightening the screw by force will cause damage to the screw or deviation of
focus.
Note: The object may be out of focus when using a source of near-infrared light than
using the visible light.
Caution for Mounting the Lens
Follow the indication shown in the figure for the protrusion between a lens and the camera
body. This camera wears mount for use with the CS-mount lens at the factory shipment.
Use the supplied C-mount adapter when using the C-mount lens.
The lens less than 450 g (0.99 lbs) can be mounted on the camera. If the lens is heavier,
both the lens and camera should be
secured by the supporter.
C-mount: Less than 13 mm (1/2”)
CS-mount: Less than 8 mm (5/16”)
MOUNTING LENS/FOCUS ADJUSTMENT
• Mounting from the Top
Remove the mount adapter from the bottom of the camera by removing the two fixing
screws. Attach the mount adapter to the top as shown in the figure, then mount the
camera on the mounting bracket.
Cation:
Be sure to use two original fixing
screws for the mount adapter.
Longer screws may damage the inner
components. Or shorter screws may
cause the camera drop.
INSTALLATION OF CAMERA
Flange-back
Adjusting Ring & Screw
Installation of Auto Iris Lens Connector
Install the lens connector (YFE4191J100) when using a video drive ALC lens.
(1) Cut the iris control cable at the edge of the lens connector to remove the existing lens
connector and then remove the outer cable cover as shown in the figure below.
The pin assignment of the lens connector is as follows:
Pin 1: Power source; +9 V DC, 50 mA max.
Pin 2: Not used
Pin 3: Video signal; 0.7 V[p-p]/40 kΩ
Pin 4: Shield, ground
(2) Solder the lens cable to the pins of the
supplied connector.
Pin 3
Pin 4
Pin 2
Rib
Pin 1
C-mount Adapter
Fixing Screws
Mount Adapter
Lens Mount
■ Connections
Precaution:
The following connections should be made by qualified service personnel or system
installers in accordance with NEC 725-51.
Note: For the WV-CP474E Colour CCTV Camera, do not use a transformer larger than
10 VA.
• Power supply connection
Recommended wire gauge sizes for 24 V AC line.
Cautions:
1. CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY. Be sure to connect
the grounding lead to the GND terminal.
2. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for
the Input Terminal.
3. The connections should comply with National Electrical Code (NEC).
CONNECTIONS
Alarm Connections
1. Connect an external sensor to the DAY/NIGHT terminal.
2. Connect an external device such as a buzzer or lamp to the ALARM terminal.
• The alarm output terminal is an open collector terminal with a capacity of 16 V DC, 100
mA or less.
OFF: Open contact
ON: 100 mA or less
• Color/black-and-white input terminal with a capacity of 5 V DC pull-up input, 0.2 mA or
more.
OFF: Open contact
ON: Closed contact
Notes:
• Use a relay unit if the voltage or current of the connected device exceeds the ratings.
• To validate the Day/Night function, set BW mode to EXT on the special menu.
Copper wire size
(AWG)
#18
(0.83 mm
2
)
#24
(0.22 mm2)
Length of cable
(Approx.)
(m)
(ft)
#22
(0.33 mm2)
#20
(0.52 mm2)
20 30 45 75
65 100 160 260
Cautions:
1. Shrinking the cable-entry seal is a one-time procedure. Do not shrink the cable-entry
seal until it has been ascertained that the unit is functioning.
2. CONNECT THIS TO 24 V AC CLASS 2 POWER SUPPLY ONLY. Be sure to connect
the grounding lead to the GND terminal.
3. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for
the Input Terminal.
4. The connections should comply with National electrical Code (NEC).
Power Cable
Video Output Cable
BNC Plug
Black (Live)
White (Neutral)
Green/Yellow (Ground)
BNC Plug
To Video IN
(CAMERA IN)
24 V AC, 60 Hz
(19.5 V-28 V)
CLASS 2 SUPPLY ONLY)
BNC Plug
Loading...