Panasonic WV-CP460, WV-CP464 User Manual
Color CCTV Cameras
CP460
Operating Instructions
Model No. WV-CP460
WV-CP464
(Lens Option)
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SER-
VICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert
the user to the presence of
uninsulated "dangerous volt-
SA 1965
SA 1966
age" within the product's enclosure that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
The exclamation point within
an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing)
instructions in the literature
accompanying the appliance.
N0100-1020 YWV8QA5377BN Printed in Japan
N 19
For U.S.A
NOTE: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference in
which case the user will be required to correct
the interference at his own expense.
FCC Caution: To assure continued compliance, (example - use only shielded interface
cables when connecting to computer or
peripheral devices). Any changes or modifications not expressly approved by the party
responsible for compliance could void the
user’s authority to operate this equipment.
The serial number of this product may be found
on the top of the unit.
You should note the serial number of this unit
in the space provided and retain this instruction
as a permanent record of your purchase to aid
identification in the event of theft.
Model No.
Serial No.
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
PREF ACE
Panasonic's WV-CP460 (WV-CP464) series color digital camera introduces a new level of
high picture quality and high resolution through the use of a 1/3-inch interline transfer CCD
image sensor having 771 horizontal pixels (picture elements), and digital signal processing
LSIs. This model offers cutting-edge technology for advanced video surveillance.
PRECAUTIONS
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws or covers.
There are no user serviceable parts inside. Ask a qualified service person for servicing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged
by improper handling or storage.
3. Do not expose the camera to rain or moisture, or try to operate it in wet areas.
Turn the power off immediately and ask a qualified service person for servicing.
Moisture can damage the camera and also create the danger of electric shock.
4. Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty.
In case the dirt is hard to remove, use a mild detergent and wipe gently.
5. Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton
tipped applicator and ethanol.
6. Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether the camera is in use or not, never
aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may
be caused.
7. Do not operate the camera beyond the specified temperature, humidity or power
source ratings.
Use the camera under conditions where temperature is between –10°C - +50°C (14°F 122°F), and humidity is below 90%. The input power source is 120 V AC 60 Hz for WVCP460 and DC 12 V/AC 24 V for WV-CP464.
Caution:
To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for
the DC 12 V or AC 24 V Input Terminal.
FEATURES
<WV-CP460>
<WV-CP464>
qewr
t
y
o
u!0
!1
i
!2
!3
!2
!5
!3
!4
Super
Dynamic
WV-
CP460
Hi-Z G/L 75Ω
VIDEO OUT
120V AC 60Hz
GEN-LOCK
AC 24V
IN
DC 12V
IN
1
2
VIDEO OUT
GND
GEN-LOCK
LOCK
AC 24V
IN
DC 12V
IN
1
2
GND
1. The following functions are built in.
(1) Auto Light Control (ALC)/Electronic Light Control (ELC)
(2) The SUPER-D2 function eliminates interference by strong background lighting
which makes the camera picture dark, such as a spotlight.
Dynamic range of 46 dB.
(3) Various External Sync Functions, including Gen-Lock
(4) Auto/Manual White Balance Function
(5) Electronic Shutter Function
2. Signal-to-noise ratio of 50 dB
3. Minimum illumination of 0.8 lx (0.08 footcandle) with F 1.4 lenses.
4. Minimum illumination of 0.4 lx (0.04 footcandle) with Panasonic aspherical high speed
(F0.75) lenses.
5. 480 lines of horizontal resolution
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
Slide the panel to the left until it locks.
q Auto Iris Lens Connector
This connector is used to connect the auto iris lens with a 4-pin male connector supplied as a standard accessory (Part No. YFE4191J100).
w Focus Fixing Screw
e Flange-back Adjusting Ring
This ring is used to adjust the back focal length or picture focus. Rotate this ring clockwise for a C-mount lens or counterclockwise for a CS-mount lens.
r Lens (Option)
t Camera Mounting Screw Hole
This hole is used to mount the camera onto a mounting bracket.
CONNECTIONS
A. WV-CP460 (120 V AC 60 Hz)
1. Plug the AC power cord (supplied as standard accessory) into the AC Inlet Socket.
2. Connect the AC power cord to a 120V AC 60 Hz outlet.
Notes:
• Connect the power cord firmly.
• The power cord should be long enough for panning and tilting.
If the cable is too short, the power cord plug may be pulled off the camera when the
camera pans or tilts.
B. WV-CP464 (12 V DC/24 V AC)
The WV-CP464 has an AC/DC compatible input terminal. The 12 V DC or 24 V AC power
supply cord can be connected to this terminal. The camera detects the power source automatically.
1. 12 V DC Power Supply
Connect the power cord to the AC/DC compatible input terminal on the rear panel of the
camera.
Resistance of copper wire [at 20°C (68°F)]
Copper wire #24 #22 #20 #18
size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)
12 V DC
(10.8 V - 16 V)
Resistance 0.078 0.050 0.030 0.018
Ω/m
Resistance 0.026 0.017 0.010 0.006
Ω/ft
• Calculation of maximum cable length between camera and power supply
10.8 V DC ≤ V
L : Cable length (m)
A - (R x 0.42 x L) ≤ 16 V DC
R : Resistance of copper wire (Ω/m)
A : DC output voltage of power supply
V
unit
L standard = (m)
L minimum = (m)
L maximum = (m)
V
A − 12
0.42 x R
A
V
− 16
0.42 x R
V
A − 10.5
0.42 x R
6. High quality picture:
AC 24V
IN
DC 12V
IN
1
2
GND
(a) 2H type vertical enhancer for greater picture sharpness
(b) Chroma averaging circuit for better color signal-to-noise ratio
(c) Minimum of aliasing on fine objects
(d) Expanded dynamic range by use of knee circuit
(e) Highlight aperture correction for greater picture detail of bright objects
7. Ability to shoot indoor scenes with fixed iris lens by use of Electronic Light Control (ELC)
function.
8. Selectable electronic sensitivity enhancing modes including AUTO, MANUAL and OFF
9. Built in Digital Motion Detector
y Down Button ( )
This button is used to move the cursor downward. It is also used to select items in the
CAM SET UP menu.
u Left Button ( )
This button is used to move the cursor to the left. It also selects the mode and can be
used to adjust some levels.
i Up Button ( )
This button is used to move the cursor upward. It is also used to select items in the
CAM SET UP menu.
o Right Button ( )
This button is used to move the cursor to the right. It also selects the mode and can be
used to adjust some levels.
!0 Set Button ( )
This button is used to activate an item selected in the CAM SET UP menu.
!1 Gen-lock Termination Switch (Hi-Z, G/L 75 Ω)
Set this switch to Hi-Z when a gen-lock video input signal is looped through. In all other
cases, set this switch to 75 Ω.
!2 Gen-lock Input Connector (GEN-LOCK)
This connector is used to connect an external system for synchronization.
!3 Video Output Connector (VIDEO OUT)
This connector is used to connect the VIDEO IN connector of the monitor.
!4 AC Inlet Socket
This socket is used to connect the power cord (supplied as a standard accessory).
!5 AC/DC Compatible Input Terminal
(DC 12 V IN/AC 24 V IN)
This terminal is for connecting the 12 V DC or 24 V AC power supply cord.
Cautions:
1. Connect to 12 V DC (10.8 V-16 V) or 24 V AC (19.5 V-28 V) class 2 power supply
only. Make sure to connect the grounding lead to the GND terminal when the power
is supplied from a 24 V AC power source.
2. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for
the Input Terminal.
2. 24 V AC Power Supply
Connect the power cable to the AC/DC compatible input terminal on the rear panel of
the camera.
Recommended wire gauge sizes for 24 V AC line.
Copper wire #24 #22 #20 #18
size (AWG) (0.22mm2) (0.33mm2) (0.52mm2) (0.83mm2)
24 V AC, 60 Hz
(19.5 V - 28 V)
Length (m) 95 150 255 425
of Cable
(Approx.) (ft) 314 495 842 1 403
Caution:
To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007).
Video Cable
1. It is recommended to use a monitor whose resolution is at least equal to that of the
camera.
2. The maximum extensible coaxial cable length between the camera and the monitor is
shown below.
Type of RG-59/U RG-6U RG-11/U RG-15/U
coaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V)
Recommended (m) 250 500 600 800
maximum
cable length (ft) 825 1 650 1 980 2 640
Installation of Auto Iris Lens Connector
Install the lens connector (YFE4191J100) when using a video drive ALC lens.
The installation should be made by qualified service personnel or system installers.
(1) Cut the iris control cable at the edge of the lens connector to remove the existing lens
connector and then remove the outer cable cover as shown in the diagram below.
The pin assignment of the lens connector is as follows:
Pin 1: Power source; +9 V DC, 50 mA max.
Pin 2: Not used
Pin 3: Video signal; 1.3 V[p-p]/40 kΩ
Pin 4: Shield, ground
(2) Solder the lens cable to the pins of the
Pin 3
Pin 1
Rib
Pin 4
Pin 2
supplied connector.
Mounting the Lens
Caution:
Before you mount the lens, loosen the screw on the side of the camera, and rotate this
ring clockwise until it stops. If the ring is not at the end, the inner glass or CCD image
sensor may be damaged.
1. Mount the lens by turning it clockwise
on the lens mount of the camera.
2. Connect the lens cable to the auto iris
lens connector on the side of the cam-
Screw
q
era.
w
Flange-back
Adjusting Ring
Caution for Mounting the Lens
The lens mount should be a C-mount or CS-mount (1”-32UN) and the lens weight should be
less than 450 g (0.99 lbs). If the lens is heavier, both the lens and camera should be
secured by using the supporter.
The protrusion at the rear of the lens should be as shown below:
C-mount: Less than 13 mm (1/2”)
CS-mount: Less than 8 mm (5/16”)
FOCUS OR FLANGE-BACK ADJUSTMENT
The following adjustment should be made by qualified service personnel or system
installers.
1. Loosen the screw on the side of the
camera.
2. Turn the flange-back adjusting ring to
the desired position.
Caution: When the C-mount lens is
mounted, do not rotate the ring
counterclockwise by force after it
stops. If the ring is rotated by
force, the inner lens or CCD image
sensor may be damaged.
3. Tighten the screw on the side of the
camera.
Focusing of
CS-mount lens
Screw
Focusing of
C-mount lens
Flange-back
Adjusting Ring
Caution: Tightening the screw by force will cause damage to the screw or deviation of
focus.
INSTALLA TION OF CAMERA
• Mounting from the top
Remove the mount adapter from the bottom of the camera by removing the two fixing
screws. Attach the mount adapter to the top as shown in the diagram, then mount the
camera on the mounting bracket.
Make sure that the two original fixing
screws are used when mounting the
mount adapter as longer length screws
may damage inner components.
Fixing Screws
Mount Adapter
Loading...