Panasonic WV-CP280, WV-CP284 User Manual

Color CCTV Cameras

Operating Instructions

Model Nos. WV-CP280

WV-CP284

V-CP284

W

ENGLISH

OCK

L

(Lens: Option)

WV-CP284 is shown above.

please read these instructions carefully and save this manual for future use.

Before attempting to connect or operate this product,

No model number suffix is shown in this manual.

FRANÇAIS

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrow­head symbol, within an equilater­al triangle, is intended to alert the
user to the presence of uninsu­lated "dangerous voltage" within
the product's enclosure that may

SA 1965

SA 1966

be of sufficient magnitude to con­stitute a risk of electric shock to
persons.

The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and mainte­nance (servicing) instructions in
the literature accompanying the
appliance.

This Class A digital apparatus complies with

For Canada

Canadian ICES-003.

For U.S.A

NOTE: This equipment has been tested and
found to comply with the limits for a Class A dig­ital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide rea­sonable protection against harmful interference
when the equipment is operated in a commer­cial environment. This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance with
the instruction manual, may cause harmful inter­ference to radio communications.
Operation of this equipment in a residential area
is likely to cause harmful interference in which
case the user will be required to correct the
interference at his own expense.

FCC Caution: To assure continued compliance,
(example - use only shielded interface cables
when connecting to computer or peripheral
devices). Any changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate this equipment.

Power disconnection. Unit with
or without ON-OFF switches
have power supplied to the unit
whenever the power cord is
inserted into the power source;
however, the unit is operational
only when the ON-OFF switch is
in the ON position. The power
cord is the main power discon­nect for all units.

WARNING:

• This apparatus must be earthed.

• Apparatus shall be connected to a main socket outlet with a protective earthing connection.

• The mains plug or an appliance coupler shall remain readily operable.

• To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture.

• The apparatus should not be exposed to dripping or splashing and that no objects filled with liquids, such
as vases, should be placed on the apparatus.

• All work related to the installation of this product should be made by qualified service personnel or system
installers.

• For PERMANENTLY CONNECTED APPARATUS provided neither with an all-pole MAINS SWITCH nor
an all-pole circuit breaker, the installation shall be carried out in accordance with all applicable installation
rules.

• The connections should comply with local electrical code.

The serial number of this product may be found
on the surface of the unit.
You should note the serial number of this unit in
the space provided and retain this book as a
permanent record of your purchase to aid identi­fication in the event of theft.

Model No.
Serial No.

2

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.

ENGLISH

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.

S3125A

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.

3

Limitation of Liability

THIS PUBLICATION IS PROVIDED "AS IS"
WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO, THE IMPLIED WAR­RANTIES OF MERCHANTABILITY, FITNESS
FOR ANY PARTICULAR PURPOSE, OR
NON-INFRINGEMENT OF THE THIRD
PARTY'S RIGHT.

Disclaimer of Warranty

IN NO EVENT SHALL MATSUSHITA ELEC­TRIC INDUSTRIAL CO., LTD. BE LIABLE TO
ANY PARTY OR ANY PERSON, EXCEPT FOR
REPLACEMENT OR REASONABLE MAINTE­NANCE OF THE PRODUCT, FOR THE
CASES, INCLUDING BUT NOT LIMITED TO
BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING

WITHOUT LIMITATION, DIRECT OR
INDIRECT, SPECIAL, CONSEQUENTIAL
OR EXEMPLARY, ARISING OUT OF OR
RELATING TO THE PRODUCT;

(2) PERSONAL INJURY OR ANY DAMAGE

CAUSED BY INAPPROPRIATE USE OR
NEGLIGENT OPERATION OF THE USER;

(3) UNAUTHORIZED DISASSEMBLE,

REPAIR OR MODIFICATION OF THE
PRODUCT BY THE USER;

(4) INCONVENIENCE OR ANY LOSS ARIS-

ING WHEN IMAGES ARE NOT DIS­PLAYED, DUE TO ANY REASON OR
CAUSE INCLUDING ANY FAILURE OR
PROBLEM OF THE PRODUCT;

THIS PUBLICATION COULD INCLUDE
TECHNICAL INACCURACIES OR TYPO­GRAPHICAL ERRORS. CHANGES ARE
ADDED TO THE INFORMATION HEREIN, AT
ANY TIME, FOR THE IMPROVEMENTS OF
THIS PUBLICATION AND/OR THE CORRE­SPONDING PRODUCT (S).

(5) ANY PROBLEM, CONSEQUENTIAL

INCONVENIENCE, OR LOSS OR DAM­AGE, ARISING OUT OF THE SYSTEM
COMBINED BY THE DEVICES OF THIRD
PARTY;

(6) ANY CLAIM OR ACTION FOR DAM-

AGES, BROUGHT BY ANY PERSON OR
ORGANIZATION BEING A PHOTO­GENIC SUBJECT, DUE TO VIOLATION
OF PRIVACY WITH THE RESULT OF
THAT SURVEILLANCE-CAMERA'S PIC­TURE, INCLUDING SAVED DATA, FOR
SOME REASON, BECOMES PUBLIC OR
IS USED FOR THE PURPOSE OTHER
THAN SURVEILLANCE.

4

CONTENTS

Important Safety Instructions ..................................................................................................... 3

Limitation of Liability ................................................................................................................... 4

Disclaimer of Warranty ............................................................................................................... 4

Preface ....................................................................................................................................... 6

Precautions ................................................................................................................................ 6

Major Operating Controls and Their Functions ........................................................................... 8

Installations and Connections .................................................................................................... 11

Specifications ............................................................................................................................. 15

Standard Accessories ................................................................................................................ 15

5

Preface

The WV-CP280/WV-CP284 is surveillance color CCTV camera equipped with a 1/3 inch CCD
solid-state image sensor with 768 of horizontal pixels.
The WV-CP280/WV-CP284 is provided with the adaptive black stretch function, high resolution
of 540 TV lines (horizontal), and minimum illuminance of 0.8 lx {0.08 foot-candle} (F1.4) thanks
to the adoption of the newly-developed digital signal processor.

Precautions

Do not attempt to disassemble the cam­era.

To prevent electric shock, do not remove
screws or covers.
There are no user-serviceable parts inside.
Ask qualified service personnel for servicing.

Do not drop metallic parts through slots.

This could permanently damage the appara­tus.
Turn the power off immediately and contact
qualified service personnel for service.

Use this product for indoor use only.

Do not expose this product to direct sunlight
for hours and do not install the product near
a heater or an air conditioner. Otherwise, it
may cause deformation, discoloration and
malfunction. Keep this product away from
water.

To keep on using with stable performance

• Parts of this product may deteriorate and
it may shorten the lifetime of this product
when using in locations subject to high
temperatures and high humidity. Do not
expose the product to direct heat such
as from a heater.

• Use this product at temperature within
–10 °C - +50 °C {14 °F - 122°F} and
humidity below 90 %. (When using this
product without turning the power off)

Handle the camera with care.

Do not abuse the camera. Avoid striking,
shaking, etc. The camera could be damaged
by improper handling or storage.

Cleaning the camera body

Turn the power off when cleaning of the cam­era. Use a dry cloth to clean the camera.
Do not use strong abrasive detergent when
cleaning the camera body. When the dirt is
hard to remove, use a mild detergent and
wipe gently. Then, wipe off the remaining
detergent with a dry cloth.
Otherwise, it may cause discoloration. When
using a chemical cloth for cleaning, read the
caution provided with the chemical cloth
product.

Discoloration on the CCD color filter

When continuously shooting a bright light
source such as a spotlight, the color filter of
the CCD may have deteriorated and it may
cause discoloration. Even when changing the
fixed shooting direction after continuously
shooting a spotlight for a certain period, the
discoloration may remain.

6

Do not aim the camera at strong light
sources.

A light source such as a spot light causes a
blooming (light bleeding) or a smear (vertical
lines).

• Locations subject to vibrations (This
product is not designed for on-vehicle
use.)

• Locations subject to condensation as the
result of severe changes in temperature

Smear

Blooming

Bright subject

Installing place

Contact your dealer for assistance if you are
unsure of an appropriate place in your partic­ular environment.
Make sure that the installation area is strong
enough to hold the camera, such as a con­crete ceiling. When the installation area is not
strong enough, reinforce and strengthen it.

Avoid installing in the following locations.

• Locations where it may get wet from rain
or water splash

• Locations where a chemical agent is
used such as a swimming pool (not only
outdoor)

• Locations subject to steam and oil smoke
such as a kitchen

• Locations near flammable gas or vapor

• Locations where radiation or x-ray emis­sions are produced

• Locations subject to strong magnetic
field or radio waves

• Locations where corrosive gas is pro­duced

• Locations where it may be damaged by
briny air such as seashores

• Locations where the temperature is not
within –10 °C - +50 °C {14°F - 122°F}.

Be sure to remove this apparatus if it is
not in use.

Radio interference

When the camera is used near TV/radio
antenna, strong electric field or magnetic
field (near a motor or a transformer), images
may be distorted and noise sound may be
produced.

Mounting screws

It is necessary to procure screws or bolts to
mount the camera. Prepare them according
to the material and strength of the area where
the camera is to be installed. The screws and
bolts must be tightened with an appropriate
tightening torque according to the material
and strength of the installation area.

7

Major Operating Controls and Their Functions

GND

VIDEO OUTVIDEO OUT

AC 24V IN :
DC 12V IN :

q

we

r

t

i

!0

oo

u

INT

ALCONON

B.S.

ON

BLCD/N

LL

ELC

OFF

OFF

OFF

!0

INT

ALCONON

B.S.

ON

BLCD/N

LL

ELC

OFF

OFF

OFF

-

-

WV-CP280 WV-CP284

LOCK

WV-CP284

y

1L 2N

8

q Flange-back adjustment ring

This ring adjusts the back-focal distance
or picture focus.

Important:

• When an object is out of focus
because it is too close to the cam­era, focus on a darker object with the
aperture open.

w ALC lens connector

Supplies power and control signals to an
auto iris lens (optional).

e Lens (optional)

Important:

• The lens mount should be a CS­mount (1"-32UN).

• The protrusion at the rear of the lens
should be as shown in the diagram
to prevent the camera's damage.

CS-mount: Less than 8 mm {5/16"}

r Flange-back lock screw

Loosen this screw with a screwdriver to
adjust the flange-back adjustment ring.
When completing the adjustment, tighten
this screw.
Recommended tightening torque:

0.05 N·m {0.5 kgf·cm}

Important:

• When the screw is tightened stronger
than the recommended tightening
torque, it may strip the thread or
cause focus misalignment.

tom, however, a top-mounting type is
also available. To mount from the top,
remove the mount adapter from the bot­tom of the camera by removing two fixing
screws.
Attach the mount adapter to the top as
shown in the diagram, then mount the
camera on the mounting bracket. Make
sure that two original screws are used
when mounting the mount adapter;
longer type screws may damage inner
components, too shorter type screws
may cause the camera drop.

y Power cord (WV-CP280 only)

Connect this power cord to an electrical
outlet of 120 V AC 60 Hz.

u 24 V AC/12 V DC input terminal [AC

24V IN/DC 12V IN] (WV-CP284 only)

This terminal is for connecting the 24 V
AC 60 Hz/12 V DC power supply cord.

i GND terminal (WV-CP284 only)

o Video output connector [VIDEO OUT]

Composite video signals are transmitted.
If this unit is connected to the multiplex
unit, the multiplexed VD2 that is priori­tized over INT/LL is automatically select­ed.

!0 Dip switch

Selects ON/OFF for light control mode,
backlight compensation, Adaptive Black
Stretch, simple day/night mode, and
INT/LL for synchronization mode.

B.S.

BLCD/N

ALC

ON

ON

ON

INT

t Mount adapter

The camera mounting screw hole is for
mounting the camera onto a mounting
bracket. The camera is originally
designed to be mounted from the bot-

OFF

OFF

OFF

LL

ELC

9

• Simple day/night mode selector [D/N]

ON: The camera selects black-and-white

mode if the picture is dark, or color
mode if the picture is bright enough.

OFF: Color picture is displayed normally.
Default setting: OFF

Note:

• The simple day/night function is
established by utilizing the sense up
function for B/W images. The IR filter
is secured.

• Adaptive Black Stretch Selector [B.S.]

ON: The dark area of the object is auto-

matically corrected to lighten it.

OFF: Does not compensate.
Default setting: ON

Important:

• In the case of "ON" setting, noise
may be increased in the dark area of
the object.
In addition, darkness and brightness
may be emphasized in the vicinity of
the boundary between the dark and
bright areas.

• Backlight compensation selector
[BLC]

ON: Compensates the background auto-

matically if it is brighter than the
object.

OFF: This mode is used when the front of

the object is extremely bright.

Default setting: OFF

Note:

• Under conditions such as extremely
strong backlight, the desired com­pensation effect may not be
achieved even with this mode set to
ON to detect the backlight level.

• Synchronization mode selector
[INT/LL]

Selects the camera synchronization
mode as either internal sync mode (INT)
or line-lock mode (LL).

INT: Sets to internal 2:1 interlace
LL: Sets to line-lock mode
Default setting: INT

• Light control mode selector [ALC/ELC]

ALC: Adjusts the lens iris automatically.
ELC:

Select this mode when a fixed iris
lens or manual iris lens is used with this
camera.

Default setting: ALC

10