Page 1
Before attempting to connect or operate this product,
please read these instructions completely.
Indoor Camera Housing
WV-7110A
Page 2
-2-
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The serial number of this product may be found on the bottom of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No. WV-7110A
Serial No.
Page 3
-3-
CONTENTS
PREFACE .................................................................... 3
PRECAUTI0NS ............................................................ 3
INSTALLATION ........................................................... 4
LENS FOCUS ADJUSTMENT .................................... 10
SPECIFICATIONS ...................................................... 11
ACCESSORIES .......................................................... 11
PREFACE
The Panasonic's WV-7110A Camera Housing is
designed to be used for indoor applications. This housing can easily be installed after the camera adjustment
and installation had been completed.
PRECAUTIONS
• It is designed for indoor use. Avoid using it in the
extreme environment where the rain falls directly,
extremely high temperature and humidity generate.
• Do not use the housing in the condition where the
sunlight directly falls to the housing. It may
increase interior temperature of the housing
extremely high.
• Use a dry cloth to clean the housing if it is dirty. If
the dirt is formidable, it is advisable to use a mild
detergent and wipe gently.
Page 4
-4-
2. Mounting of the Camera
2-1. Mount the camera mounting bracket or the pan/tilt
mechanism onto the mounting adaptor of the camera.
When the cameras and lenses shown below are
installed into this housing, choose the suitable
angle according to the following tables.
INSTALLATION
A.Mounting from top
1. Disassembling of camera housing
Remove the Front Case, Rear Cover and Upper/
Lower Covers as shown in the following.
WV-LA6/LA12
WV-LA4.5/LA6B2/LA12B2
WV-LA8B/LA16B/LA25B/LA50B
WV-LM6B2/LM12B2
Lens
WV-BL200 Series
WV-BL600 Series
Camera
Mounting Adaptor
WV-LA2.8 Angle-B
Use Angle
APPLICABLE MODELS AND MOUNTING
Upper Cover Rear Cover
Mounting Adaptor
Front Case
1
3
Lower Cover
2
Page 5
-5-
See below.
Lens
WV-CP460 Series
WV-CP470 Series
WV-CP240 Series
WV-BP140 Series
Camera
Angle-A
Apply the placing directions and fixing holes shown below.
Use Angle
ABCDEF
Hole
Hole
<180˚ Reversal Position><Normal Position>
FE
Use properly the other side applicable hole,
besides the hole A through F.
DCBA
Lens
Camera
WV-LA908C3
WV-LA408C3
WV-LZA61/2
WV-LZF61/2
WV-LA210C3
WV-LA9C3B
WV-LA4R5C3B
WV-LA2R8C3B
WV-LZ62/8
WV-LZ61/10
WV-LA12A
WV-LA4R5A
WV-LA6A
WV-CP460 series A C (180° reversal) B A
WV-CP470 series D F (180° reversal) F F (180° reversal)
WV-CP240 series
WV-BP140 series
DE (180° reversal) F E (180° reversal)
APPLICABLE MODELS AND MOUNTING
Page 6
-6-
a.Mounting of the Angle-A(supplied)
a-1. Remove the mounting adaptor of the camera by
removing the two mounting adaptor fixing screws.
Note: Use the supplied screws when fixing the Angle-
A or Angle-B. Using shorter ones may cause the
camera to fall down, or longer ones may damage
the inside of the camera.
a-2. Fix the Angle-A onto the camera by using the two
Angle Fixing Screws(supplied) as shown in the following.
Angle-A (normal)
Angle-A (180° reversal)
Mounting Adaptor
Angle Fixing Screws (supplied)
Angle-A (supplied)
Angle Fixing Screws (supplied)
Page 7
-7-
a-3. Be sure to stick the Angle Seat(supplied) onto the
Angle-A.
Caution: When the left and right pan limit screws
should be removed from the pan/tilt unit due to the
Angle-A installation, use the Angle Seat as shown
below.
b.Mounting of the Angle-B(supplied)
b-1. Remove the mounting adaptor of the camera by
removing the two mounting adaptor fixing screws.
b-2. Fix the Angle-B onto the camera by using the two
Angle Fixing Screws(supplied) as shown in the
following.
Angle seat (supplied)
Mounting Adaptor
Angle Fixing Screws (supplied)
Angle-B (supplied)
Cut here when using
the Angle-A (normal)
Cut here when using
the Angle-A (180° reversal)
Page 8
-8-
b-3. Re-install the mounting adaptor on the Angle-B.
2-2. Complete the adjustment and connections
required for the camera operation.
2-3. Mount the camera mounting bracket or the pan/tilt
mechanism onto the mounting adaptor of the camera.
3. Installation of Upper and Lower Cover
3-1. Place the Upper Cover on the camera.
3-2. Attach the Lower Cover to the Upper Cover.
Note: Do not clamp the cable with this installation.
Page 9
-9-
3-3. Attach the Front Case to the Upper and Lower
Covers.
4. Installation of Rear Cover
Attache the Rear Cover as shown in the following.
Note:
1. Be sure to insert the cable opening side to this
housing first.
2. If the cable opening is too small due to the number
of coaxial cable, enlarge the cable opening by
cutting off the Rear Cover.
Cut off the
shaded portion
Page 10
-10-
5 Cable Clamp
5-1. Attach the Cable Clamp (supplied) to the housing.
5-2. Clamp the cables with the cable clamp.
B.Mounting from bottom
The Upper and Lower Cover must be attached on
the camera in reverse.
LENS FOCUS ADJUSTMENT
When the focus adjustment is required, remove the
Front Case.
Note: When the WV-LZ61/10 or WV-LZ62/8 is
mounted on the camera, adjust the lens focus
before mounting the upper cover, lower cover,
and front case.
CAUTION:
The reflection of the power indicator on the
front of camera may be displayed in the picture.
In this case, seal the LED by using the Power
Indicator Masking Label on the LED.
Page 11
-11-
SPECIFICATIONS
Dimensions : 133(W) X 83(H) X 320(D) mm
5-1/4"(W) X 3-1/4"(H) X 12-5/8"(D)
Weights : 0.5 kg(1.1 lbs.)
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.
ACCESSORIES
Angle-A..................................................................1 pc.
Angle-B..................................................................1 pc.
Angle Fixing Screw................................................2 pcs.
Angle Seat .............................................................1 pc.
Cable Clamp..........................................................1 pc.
Power Indicator Masking Label .............................1 pc.
Page 12
Panasonic Digital Communications & Security Company
Unit Company of Matsushita Electric Corporation of America
Security Systems
www.panasonic.com/cctv
Executive Office : One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Zone Office
Eastern : One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303
Central : 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205
Western : 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905) 624-5010
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.
San Gabriel Industrial Park 65th, Infantry Ave. KM. 9.5 Carolina, P.R. 00985 (809) 750-4300
2001 © Matsushita Communication Industrial Co., Ltd.
N0694-2092 V8QA3353CN Printed in Japan
N 19
Loading...