Panasonic WJ-PB85t08 Operating Instructions

-1-
Before attempting to connect or install this product,
please read these instructions carefully and save this manual for future use.
Extend Card (O.S.D.)
1
2
3
4
5
6
7
8
MONITOR OUT
VIDEO IN
q
w
Model No. WJ-PB85T08

Preface

The WJ-PB85T08 On Screen Display Board is an optional board for displaying the camera title, clock, and system status on the active monitors.

Appearance

q Monitor Output Connector (MONITOR OUT, 1 - 8)
Outputs the video signal connected to the VIDEO IN port with the character display for the video monitor.
w Video Input Port (VIDEO IN)
Accepts the video signal from the VIDEO OUT Port on the WJ-PB85M16 Cross Point Output Board of the Cross Point cage (MXSW).
17 16 15 14
5 4 3 2 1
20 19 18
8 6
23 22 21
11 10 9
7
25 24
13 12
Pin No. Designation
25 24 23 22 21 20 19 18 17 16 15 14
VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7 VIDEO 8 Not used Not used Not used Not used
Pin No. Designation
13 12 11 10
9 8 7 6 5 4 3 2 1
Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground Ground
Hold this board only by its edges. Otherwise components on the board may be damaged by static electricity.
Caution
SW Positions
Monitor Output
Board
No.
SW2 SW1
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 1 2 3 4 5 6 7 8 9 A
B C D E
F
1 - 8
9 - 16 17 - 24 25 - 32 33 - 40 41 - 48 49 - 56 57 - 64 65 - 72 73 - 80 81 - 88 89 - 96
97 - 104 105 - 112 113 - 120 121 - 128
-2-

Board Setting

Before installing this board, the following settings should be made by qualified service personnel or system installers.
SW3
SW2SW1SW5
OFF
1234
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Reset Switch
1. Set switches (SW1 and SW2) on the board to designate the On Screen Display board number as shown in the following table. The factory default setting is Board Number 1 (00).
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
1
Switch Positions
-3-
2. Confirm that switches (SW3) on the board are set to the OFF position as shown below.
SW3
OFF
1234

Installation

The following installation should be made by qualified service personnel or system installers.
Installing Additional Extension
Boards
1. Remove the screws from the rear panel(s) of the WJ-SX850 Matrix Switcher Card Cage.
432
Switch Number
OFFOFFOFFOFFSW3
2. Remove the rear panel(s).
3. Remove the front panel of the cage by removing the two screws on the panel shown below.
4. Place the Boards into the specified positions in the front or rear of the Cage by sliding them along the board guides as shown below.
5. Make sure to push in the Boards until they are seat­ed firmly.
6. Secure the rear board by tightening the two screws on the board.

Specifications

Video Input 1.0 V[p-p]/75composite video signal
8 inputs 25-pin D-sub connector Video Output: 1.0 V[p-p]/75Ω composite video signal On Screen Display:
Time and Date: 3 display types selectable Camera Title: 1 Line, 30 alphanumeric characters maximum
Dimensions: Front Board; 255(W) x 250(H) x 12(D) mm
10-1/16”(W) x 9-13/16”(H) x 1/2”(D)
Rear Board; 117.5(W) x 265(H) x 20(D) mm
4-5/8”(W) x 10-7/16”(H) x 13/16”(D)
Weight: 0.6
kg (1.3 lbs)
Weight and dimensions indicated are approximate. Specifications are subject to change without notice.
NM1099-0 YWV8QA5058AN Printed in Japan
N 19
© Matsushita Communication Industrial Co., Ltd. 1999
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010
Panasonic Sales Company Division of Matsushita Electric of Puerto Rico Inc.
Ave. 65 de Infanteria. Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 (809)750-4300
Panasonic Security and Digital Imaging Company A Division of Matsushita Electric Corporation of America
Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Regional Offices:
Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 (770) 338-6838 Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5211 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840
Board
Tighten screws
Tighten screws
Rear
panel
Rear
panel
Tighten screws
7. Close open spaces on the rear of the Cage with the supplied rear panel(s).
8. Close the front of the cage by fixing the front panel.
Loading...