Panasonic VDR-D220EB User Manual

LSQT1157_EB.book 1 ページ２００６年１２月１１日　月曜日　午後８時４６分

Operating Instructions

DVD Video Camera

Model no. VDR-D310EB

VDR-D220EB

Before use, please read these instructions completely.

LSQT1157 A

LSQT1157_EB.book 2 ページ２００６年１２月１１日　月曜日　午後８時４６分

Dear Customer,

We would like to take this opportunity to thank you for purchasing this Panasonic Movie Camera. Please read these Operating Instructions carefully and keep them handy for future reference. Please note that the actual controls and components, menu items, etc. of your Movie Camera may look somewhat different from those shown in the illustrations in these Operating Instructions.

Caution for AC mains lead

For your safety, please read the following text carefully.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark Ï or the BSI mark Ì on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local dealer.

CAUTION!

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13-AMPERE SOCKET.

If a new plug is to be fitted please observe the wiring code as stated below. If in any doubt please consult a qualified electrician.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code: Blue: Neutral, Brown: Live. As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black or Blue. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Brown or Red.

WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E, BY THE EARTH SYMBOL Ó OR COLOURED GREEN OR GREEN/YELLOW.

THIS PLUG IS NOT WATERPROOF—KEEP DRY.

Before use

Remove the connector cover.

How to replace the Fuse

The location of the fuse differ according to the type of AC mains plug (figures A and B). Confirm the AC mains plug fitted and follow the instructions below. Illustrations may differ from actual AC mains plug.

1) Open the fuse cover with a screwdriver.

Figure A Figure B

Fuse cover

2) Replace the fuse and close or attach the fuse cover.

Figure A Figure B

Fuse (5 ampere)

LSQT1157

LSQT1157_EB.book 3 ページ２００６年１２月１１日　月曜日　午後８時４６分

Information for Your Safety

The socket outlet shall be installed near the

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE, ≥ DO NOT EXPOSE THIS APPARATUS TO

RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

≥ USE ONLY THE RECOMMENDED

ACCESSORIES.

≥ DO NOT REMOVE THE COVER (OR

BACK); THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

equipment and easily accessible. The mains plug of the power supply cord shall remain readily operable. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from AC receptacle.

Product Identification Marking is located on the bottom of unit.

Use only the recommended accessories.

≥ Do not use any other AV/S cables and USB

cables (VDR-D310) except the supplied one.

≥ When you use the cable which are sold

separately, please make sure to use the one whose length is less than 3 meters.

CAUTION!

≥ DO NOT INSTALL OR PLACE THIS UNIT

IN A BOOKCASE, BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE. ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.

≥ DO NOT OBSTRUCT THE UNIT’S

VENTILATION OPENINGS WITH NEWSPAPERS, TABLECLOTHS, CURTAINS, AND SIMILAR ITEMS.

≥ DO NOT PLACE SOURCES OF NAKED

FLAMES, SUCH AS LIGHTED CANDLES, ON THE UNIT.

≥ DISPOSE OF BATTERIES IN AN

ENVIRONMENTALLY FRIENDLY MANNER.

CLASS 1 LASER PRODUCT IEC 60825-1:2001

CAUTION This product contains a laser diode of higher class than 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.

LSQT1157

LSQT1157_EB.book 4 ページ２００６年１２月１１日　月曜日　午後８時４６分

Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)

This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery

and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

LSQT1157

LSQT1157_EB.book 5 ページ２００６年１２月１１日　月曜日　午後８時４６分

∫ Indemnity concerning recording

content

The manufacturer shall in no event be liable for the loss of recordings due to malfunction or defect of this unit, its accessories or recordable media.

∫ Carefully observe copyright laws

Recording of pre-recorded tapes or discs or other published or broadcast material for purposes other than your own private use may infringe copyright laws. Even for the purpose of private use, recording of certain material may be restricted.

≥ SDHC Logo is a trademark. ≥ miniSD Logo is a trademark. ≥ The Movie Camera uses copyright-protected

technologies and is protected by the patented technologies and intellectual properties of Japan and the U.S. To use these copyrightprotected technologies, authorization of the Macrovision Company is required. It is prohibited to disassemble or modify the Movie Camera.

≥ Manufactured under license from Dolby

Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

≥ LEICA is a registered trademark of Leica

microsystems IR GmbH and DICOMAR is a registered trademark of Leica Camera AG.

≥ Other names of systems and products

mentioned in these instructions are usually the registered trademarks or trademarks of the manufacturers who developed the system or product concerned.

≥ Depending on the model, some functions are

not available.

≥ Features may vary, so please read carefully.

These operating instructions are designed for use with models VDR-D310 and VDR-D220. Pictures may be slightly different from the original. ≥ The illustrations used in these operating

instructions show model VDR-D310, however, parts of the explanation refer to different models.

LSQT1157

LSQT1157_EB.book 6 ページ２００６年１２月１１日　月曜日　午後８時４６分

Contents

Caution for AC mains lead .................... 2

Information for Your Safety................... 3

Before using

Features ..................................................8

Accessories..........................................10

Parts identification and handling .......11

Using the LCD monitor ............................. 15

Using the viewfinder .................................15

Using the remote control (VDR-D310) .....16

Discs and cards....................................18

Discs that can be used on this unit...........18

Cards that you can use with this unit........22

Disc and card handling.............................23

Setup

Power supply........................................24

Charging the battery.................................24

Connecting to the AC outlet .....................28

Turning the unit on/off............................... 28

Inserting/removing a disc....................29

Inserting/removing an SD card........... 31

Selecting a mode..................................32

How to use the joystick .......................32

Switching the language.......................36

Using the menu screen........................36

Setting date and time...........................38

Adjusting LCD monitor/viewfinder..... 39

Recording

Soft skin mode ......................................... 52

Tele macro function (VDR-D310) ............. 52

Colour night view function........................ 53

Self-timer recording.................................. 53

Recording guideline function....................54

Wide mode............................................... 54

Image stabilizer function .......................... 54

Wind noise reduction function.................. 55

Manual recording functions................ 55

Scene mode............................................. 55

Manual focus adjustment ......................... 56

White balance.......................................... 57

Manual shutter speed/

aperture adjustment ................................. 58

Playback

Motion picture playback...................... 60

Still picture playback

(JPEG still pictures)............................. 64

Editing

Editing scenes......................................66

Deleting scenes ....................................... 66

Dividing a scene....................................... 67

Combining scenes ...................................67

Using playlists......................................68

What is a playlist?.................................... 68

Creating a new playlist ............................. 68

Playing back a playlist.............................. 69

Editing a playlist....................................... 69

Editing still pictures.............................73

Deleting still pictures................................ 73

Locking still pictures ................................. 74

DPOF setting ........................................... 74

Before recording ..................................40

Recording motion pictures .................42

Recording modes and recordable time

available for the motion picture ................43

Recording still pictures

(JPEG still pictures).............................45

Number of pixels and picture quality

for still picture recording ...........................48

Various recording functions ...............49

Zoom in/out function.................................49

Recording yourself ...................................50

Backlight compensation function..............50

Fade in/fade out function..........................51

LSQT1157

Disc and card management

Disc management ................................76

Finalizing a disc ....................................... 76

Un-finalizing a DVD-RW .......................... 77

Protecting a disc ...................................... 77

Formatting discs.......................................77

Displaying disc information ...................... 78

Card management................................78

Formatting an SD card............................. 78

LSQT1157_EB.book 7 ページ２００６年１２月１１日　月曜日　午後８時４６分

With other products

With a TV...............................................80

Playback on TV........................................80

With a DVD recorder/player.................81

Playback on DVD recorder, DVD player,

computer etc.............................................81

Dubbing recordings

onto a DVD recorder’s hard disk ..............82

With a VCR............................................83

Dubbing images

onto other video devices ..........................83

With a printer (PictBridge)...................83

Others

Menus....................................................86

Menu list ...................................................86

Other menus.............................................87

Indications ............................................88

Indications ................................................88

Messages .................................................91

Functions that cannot be used

simultaneously ..........................................93

Frequently asked questions................94

Troubleshooting...................................95

Cautions for use...................................99

Explanation of terms..........................102

Specifications.....................................104

Number of recordable pictures

on an SD card ........................................106

Index....................................................110

LSQT1157

LSQT1157_EB.book 8 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

Features

∫ Easy recording! (l 42)

No need to search for the recording start position. The new recording will not overwrite any previously recorded scene.

∫ Easy playback! (l 60)

Recorded scenes are displayed as thumbnails. You can easily search for the scenes you want to watch.

∫ Editing scenes! (l 66, 68)

You can create an original video (playlist) by collecting your favourite scenes together and then easily dub this video to a VCR or a DVD recorder hard disk.

LSQT1157

LSQT1157_EB.book 9 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

If you insert a DVD-RW or a DVD-R disc recorded in this unit (that has not been finalized) into another device such as DVD recorder, computer, etc., the disc may become unusable. Be sure to finalize the disc on this unit before inserting it in other devices. (l 76)

∫ Using with DVD player/recorder! (l 81)

Just insert the disc into a DVD player/recorder compatible with 8 cm discs to play back the scenes recorded with this unit on it. If you have a DVD recorder with hard disk, you can dub scenes recorded on a disc with this unit to the hard disk.

∫ Using with a computer! (VDR-D310) (Refer to the operating instructions

for PC connection.)

You can enjoy editing scenes with the software on the supplied CD-ROM and creating original DVD-Video discs.

LSQT1157

LSQT1157_EB.book 10 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

∫ Sales and Support Information

Customer Care Centre

≥ For customers within the UK: 08705 357357 ≥ For customers within the Republic of

lreland: 01 289 8333

≥ Visit our website for product information ≥ E-mail: customer.care@panasonic.co.uk

Technical Support for AV Software ≥ For UK, ROI: 08701 505610

Direct Sales at Panasonic UK ≥ Order accessory and consumable items for

your product with ease and confidence by phoning our Customer Care Centre Monday– Thursday 9.00 a.m.–5.30 p.m., Friday 9.30 a.m.– 5.30 p.m. (Excluding public holidays)

≥ Or go on line through our Internet Accessory

ordering application at www.panasonic.co.uk

≥ Most major credit and debit cards accepted. ≥ All enquiries transactions and distribution

facilities are provided directly by Panasonic UK Ltd.

≥ It couldn’t be simpler! ≥ Also available through our Internet is direct

shopping for a wide range of finished products, take a browse on our website for further details.

Interested in purchasing an extended guarantee? Please call 0870 240 6284 or visit our website www.panasonic.co.uk/guarantee

Accessories

Check the accessories before using this unit.

Battery pack (VDR-D310)

CGA-DU12 ≥ The supplied battery pack is not available as

spare part, see the list of optional batteries below for alternative battery.

Battery pack (VDR-D220)

CGR-DU06 ≥ The supplied battery pack is not available as

spare part, see the list of optional batteries below for alternative battery.

AC adaptor

VSK0651B (DE-974GC)

DC cable

K2GJ2DC00011

AV/S cable

K2KZ9CB00001

AC cable

K2CT3CA00004 (RJA0053-3X)

Remote control (VDR-D310)

N2QAEC000023

Button-type battery (VDR-D310)

CR2025

LSQT1157

Lens cap

LSYK2004

USB cable (VDR-D310)

K1HA05CD0010

CD-ROM (VDR-D310)

2 3 4

LSQT1157_EB.book 11 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

Disc cleaning cloth

VFC3778-2

Optional accessories

Some optional accessories may not be available in some countries.

AC adaptor (VW-AD11EB)

Battery pack (lithium/CGR-DU06/640 mAh) (VDR-D220)

Battery pack (lithium/CGA-DU12/1150 mAh)

Battery pack (lithium/CGA-DU14/1360 mAh)

Battery pack (lithium/CGA-DU21/2040 mAh)

Wide conversion lens (VW-LW3707M3E) (VDR-D310)

Tele conversion lens (VW-LT3714ME) (VDR-D310)

Filter kit (VW-LF37WE)

Video DC light (VW-LDC10E)

Light bulb for video DC light (VZ-LL10E)

Stereo microphone (VW-VMS2E) (VDR-D310)

Tripod (VW-CT45E)

8 cm DVD-RAM disc (single sided/LM-AF30E)

8 cm DVD-RAM disc (double sided/ LM-AF60E)

8 cm DVD-RW disc (single sided/LM-RW30E)

8 cm DVD-RW disc (double sided/ LM-RW60E)

8 cm DVD-R disc (single sided/LM-RF30E)

8 cm DVD-R disc (double sided/LM-RF60E)

8 cm DVD-R DL disc (dual layer on single side/LM-RF55LE)

USB cable (K1HA05CD0010) (VDR-D220)

Parts identification and handling

1 Lens (LEICA DICOMAR) (VDR-D310)

Lens (VDR-D220)

2 Microphone (built-in, stereo) 3 White balance sensor (l 58)

Remote control sensor (VDR-D310) (l 17)

6 7 8

4 Menu button [MENU] (l 36) 5 Viewfinder (l 15)

Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the viewfinder screen. However, this is not a malfunction and does not affect the recorded picture.

6 Delete button [ ] (l 66, 70, 73) 7 LCD monitor open part (l 15) 8 DC input terminal [DC/C.C. IN] (l 28) 9 Battery holder (l 24) 10 Power switch [OFF/ON] (l 28) 11 Status indicator (l 28) 12 Disc/computer access lamp [ACCESS/

PC] (VDR-D310) (l 29) (Refer to the operating instructions for PC

1 1 1

LSQT1157

LSQT1157_EB.book 12 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

connection.) Disc access lamp [ACCESS/PC]

(VDR-D220) (l 29) 13 Mode dial (l 32) 14 Joystick (l 32) 15 Recording start/stop button (l 42) 16 Disc eject lever [DISC EJECT] (l 29)

17 18

28 29

31 32

19 20

17 When recording: Zoom lever [W/T] (l 49)

When playing back: Volume lever

[sVOLr] (l 62) 18 Photoshot button [ ] (l 45) 19 Accessory shoe

≥ Accessories, such as a video DC light

(optional), are attached here.

20 Eyepiece corrector knob (l 39)

21 Tripod receptacle (l 14) 22 Battery release lever [BATTERY] (l 24)

23 LCD monitor (l 15)

Due to limitations in LCD production technology, there may be some tiny bright or dark spots on the LCD monitor screen. However, this is not a malfunction and does not affect the recorded picture.

24 Terminal cover 25 Microphone terminal [MIC] (VDR-D310)

≥ A compatible plug-in powered microphone

can be used as an external microphone.

≥ When the unit is connected with the AC

adaptor, sometimes noise may be heard depending on the microphone type. In this case, please switch to the battery for the power supply and the noise will stop.

26 Audio-video output terminal [A/V]

(l 80, 83)

27 Speaker 28 Mode select switch [AUTO/MANUAL/

FOCUS] (l 41, 55, 56) 29 Reset button [RESET] (l 98) 30 Card slot cover [SD CARD] (l 31) 31 Card access lamp (l 32) 32 Card slot (l 31) 33 USB terminal [ ] (l 83)

(Refer to the operating instructions for PC

connection.) (VDR-D310)

LSQT1157

LSQT1157_EB.book 13 ページ２００６年１２月１１日　月曜日　午後８時４６分

1 Pass the end of the lens cap cord

through the belt.

Before using

34 Disc compartment (l 29) 35 Grip belt (l 13)

Using grip belt

Adjust the belt length so it fits your hand.

Adjust the belt length and the pad position.

1 Flip the belt. 2 Adjust the length. 3 Replace the belt.

Attaching the lens cap

Attach the lens cap to protect the surface of the lens. ≥ When the MC protector or the ND filter of the

Filter Kit (VW-LF37WE; optional) is attached, use the lens cap included in the Filter Kit.

2 Pass the lens cap through the

loop.

3 To attach or remove the lens cap,

hold both sides of the lens cap

with the tips of your finger and

thumb.

During recording

The removed lens cap can be attached to the lens cap fixture.

LSQT1157

LSQT1157_EB.book 14 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

≥ When 2 lens accessories, such as the ND filter

Lens hood

∫ VDR-D310

and tele conversion lens, are attached and the W/T lever is pressed toward the W side, the 4 corners of an image will be darkened. (Vignetting)

Rotate the lens hood counterclockwise A to remove it. In order to attach it, place into slot B, and then rotate it clockwise C.

∫ VDR-D220 Rotate the lens hood counter-

clockwise A to remove it. In order to attach it, rotate it clockwise B.

≥ Attach the MC protector or the ND filter of the

Filter Kit (VW-LF37WE; optional) in front of the lens hood. Do not attach the other accessories on the hood. (Except for the lens cap) (Refer to the operating instructions for the Filter Kit.)

≥ When attaching the tele conversion lens

(VW-LT3714ME; optional) or the wide conversion lens (VW-LW3707M3E; optional), first remove the lens hood. (Refer to the operating instructions for the tele conversion lens or the wide conversion lens.)

LSQT1157

≥ Do not attach the accessories on the hood.

(Except for the lens cap)

≥ When attaching the MC protector or the ND

filter of the Filter Kit (VW-LF37WE; optional), first remove the lens hood. (Refer to the operating instructions for the accessories.)

Tripod receptacle

This is a hole for attaching the unit to the optional tripod.

LSQT1157_EB.book 15 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

(Please carefully read the operating instructions for how to attach the unit to the tripod.)

≥ When the tripod is used, the card slot cover

cannot be opened. Insert an SD card before attaching this unit to the tripod. (l 31)

Using the LCD monitor

You can record the image while viewing it on the LCD monitor.

1 Place your finger on the LCD

monitor open part A and pull the LCD monitor out in the direction of the arrow.

≥ The brightness and colour level of the LCD

monitor can be adjusted from the menu. (l 39)

≥ The unit may be damaged or fail if the LCD

monitor is forcibly opened or rotated.

≥ If the LCD monitor is rotated by 180x towards

the lens and the viewfinder is extended (when recording yourself), the LCD monitor and the viewfinder simultaneously light.

Using the viewfinder

Pull out the viewfinder.

The viewfinder will be activated. (If the LCD monitor is opened, the viewfinder will be deactivated.)

≥ The brightness of the viewfinder (l 39) and

the field of view (l 39) can be adjusted.

≥ It can open up to 90o.

2 Adjust the angle of the LCD

monitor as desired.

≥ It can rotate up to 180o A towards the lens or

90o B towards the viewfinder.

LSQT1157

LSQT1157_EB.book 16 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

1 While pressing the stopper A,

Using the remote control (VDR-D310)

pull out the battery holder.

EXT

DISPLAY

DATE/

TIME

STILL ADV STILL ADV

START/

PHOTO

STOP

SHOT

ZOOM

VOL

PLAY

PAU S E

STOPSKIP SKIP

ENTER

1 Photoshot button [PHOTO SHOT, ]* 2 On-screen display button [EXT DISPLAY]

(l 81) 3 Date/time button [DATE/TIME] (l 38) 4 Playback operation buttons (l 61) 5 Delete button [ ]* 6 Direction buttons [3,4,2,1] (l 37) 7 Recording start/stop button [START/

STOP]* 8 Zoom/volume buttons [ZOOM, VOL]* 9 Menu button [MENU]* (l 37) 10 Enter button [ENTER] (l 37)

* means that these buttons function in the same

manner as the corresponding buttons on the unit.

2 Set the button-type battery with

its (r) mark facing upward and then put the battery holder back in place.

∫ Concerning the button-type battery ≥ When the button-type battery runs down,

replace it with a new battery (part number: CR2025). The battery should normally last about 1 year, however this depends on how frequently the unit is used.

≥ Keep the button-type battery out of the reach of

children.

Warning

Keep the Button-Type battery out of the reach of children. Never put Button-Type battery in mouth. If swallowed call your doctor.

∫ Install a button-type battery

Install the supplied button-type battery in the remote control before using it.

LSQT1157

LSQT1157_EB.book 17 ページ２００６年１２月１１日　月曜日　午後８時４６分

WARNING

“THE LITHIUM BATTERY IS A CRITICAL COMPONENT (TYPE NUMBER CR2025 MANUFACTURED BY PANASONIC). IT MUST NEVER BE SUBJECTED TO EXCESSIVE HEAT OR DISCHARGE. IT MUST THEREFORE ONLY BE FITTED IN EQUIPMENT DESIGNED SPECIFICALLY FOR ITS USE. REPLACEMENT BATTERIES MUST BE OF THE SAME TYPE AND MANUFACTURER. THEY MUST BE FITTED IN THE SAME MANNER AND LOCATION AS THE ORIGINAL BATTERY, WITH THE CORRECT POLARITY CONNECTIONS OBSERVED. DO NOT ATTEMPT TO RE-CHARGE THE OLD BATTERY OR RE-USE IT FOR ANY OTHER PURPOSE. IT SHOULD BE DISPOSED OF IN WASTE PRODUCTS DESTINED FOR BURIAL RATHER THAN INCINERATION.”

Before using

∫ Remote control usable range

The distance between the remote control and the unit’s remote control sensor A: Within approx. 5m Angle: Approx. 10o up and 15o down, left, and right

≥ The remote control is intended for indoor

operation. Outdoors or under strong light, the unit may not operate properly even within the usable ranges.

LSQT1157

LSQT1157_EB.book 18 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

Discs and cards

Discs that can be used on this unit

Disc type DVD-RAM

8 cm

Single sided/

DVD-RW

8 cm

Single sided/double sided

double sided

(DVD-RAM

[DVD-RW Ver. 1.1/2X-SPEED (2X/1X)]

Ver. 2.1)

Recording format DVD Video

Recording format (VR format)

DVD Video Recording format (VR format)

DVD-Video format (Video format)

Characteristic Rewritable disc Rewritable disc One time recording

disc

Display on the screen

Indication in these instructions

(RAM) (-RW‹VR›) (-RW‹V›)

Functions

≥ Deleting recorded scenes ¥¥ –

≥ Editing on this unit ¥¥ –

≥ Playback on other

products

≥ Recording after finalizing – ¥¥

LSQT1157

LSQT1157_EB.book 19 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

Disc type DVD-R

8 cm

Single sided/double sided

DVD-R DL

8cm

Dual layer on single side

(DVD-R for General Ver. 2.0) (DVD-R for DL Ver. 3.0)

Recording format DVD-Video format

(Video format)

DVD-Video format (Video format)

Characteristic One time recording disc One time recording disc

Display on the screen

Indication in these instructions

(-R)

Functions

≥ Deleting recorded scenes –

≥ Editing on this unit –

≥ Playback on other

products

≥ Recording after finalizing –

¥: available –: not available

*1 By formatting the disc, it can be used repeatedly. (l 77) *2 DVD players and DVD recorders that support 8 cm discs. *3 Playback is possible on compatible products. *4 Must be finalized on this unit. (l 76) Playback is possible on compatible products. *5 Must be finalized on this unit. (l 76) Playback of DVD-R DL is possible on compatible products. *6 Un-finalize the disc. (l 77)

LSQT1157

LSQT1157_EB.book 20 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

≥ For the purposes of these operating instructions, DVD-R and DVD-R DL are referred to as the

“DVD-R”.

≥ Still pictures cannot be recorded on a disc with this unit. ≥ You cannot record or play continuously from one side of the disc to the other when using a double

sided disc. You will need to eject the disc and turn it over.

≥ Discs inserted in a holder, cartridge, or caddy case cannot be used. Always remove bare discs from

these containers prior to use.

≥ It is recommended that you use Panasonic discs. Usually discs compatible with the DVD standard

can be used for recording and playback with no problems. However, some commercially available discs do not meet the DVD standard for quality and performance. If you use one of these discs, you may not be able to record or playback normally. (The message “FOR BEST PERFORMANCE PANASONIC DISC IS RECOMMENDED.” appears.) Refer to the following support site for information about discs that have been confirmed as compatible by Panasonic. http://panasonic.co.jp/pavc/global/cs/e_cam (This website is in English only.)

≥ Discs recorded on this unit may not be playable on other products. ≥ Recording on DVD-R in DVD Video Recording format is not supported. ≥ When using DVD-RW or DVD-R, do not perform the following as it may make the disc

unusable.

jRecord on a disc with other products after recording on it with this unit. jRecord on a disc with this unit after recording on it with other products. jInsert an un-finalized disc in any other products.

∫ About format types

What is the DVD Video Recording format (VR format)?

This is a format for recording on DVD discs which allows you to record and erase repeatedly and create playlists. You can record on DVDRAM and DVD-RW in DVD Video Recording

What is the DVD-Video format (Video format)?

By finalizing the disc, it can be played back on most DVD players. You can record on DVD-RW and DVD-R in DVDVideo format with this unit.

format with this unit.

≥ If a disc is recorded in VR format, the data can be exported on a computer.

∫ About DVD-R DL (Dual Layer)

DVD-R DL (Dual Layer) discs have two layers of recording/playback surface on one side. If the first layer (L0) becomes full during recording, the recording continues uninterrupted on the second layer (L1). However, the recorded picture is divided into 2 scenes at the point where the layers switch. The unit automatically switches layers during disc playback so you can play the whole of the disc continuously like a normal disc. However, the image or sound momentarily stop at the point where the layers switch.

∫ Examples of discs that cannot be used on this unit ≥ Discs other than those with diameter of 8 cm ≥ CD-RW ≥ Double layer discs other than DVD-R DL ≥ CD-R ≥iRW ≥ CD-ROM ≥iR ≥ CD ≥ DVD-ROM ≥ DVD-Video

LSQT1157

LSQT1157_EB.book 21 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

When using brand-new DVD-RW

When using DVD-RW, select whether to record in DVD Video Recording format (VR format) or DVDVideo format (Video format) and then format the disc. (l 20, About format types)

1 When a brand-new DVD-RW is inserted in this unit,

the screen on the right appears. Select [YES], then

press the joystick.

2 Select format type, then press the joystick.

[VIDEO]: DVD-Video format [VR]: DVD Video Recording format

3 When the confirm screen appears, select [YES],

then press the joystick.

≥ To change the format type, format the disc again. (l 77)

If the disc is formatted, then all the data recorded on the disc will be erased.

LSQT1157

LSQT1157_EB.book 22 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

Cards that you can use with this unit

Card type SD Memory Card SDHC Memory Card

8 MB, 16 MB, 32 MB, 64 MB,

Capacity

Indication in these instructions

This unit is compatible with both SD Memory cards and SDHC Memory cards. You can only use SDHC Memory cards on devices that are compatible with them. You cannot use SDHC Memory cards on devices that are only compatible with SD Memory cards. (When using an SDHC Memory card on another device, be sure to read the operating instructions for that device.)

≥ For the purposes of these operating instructions, SD Memory Card and SDHC Memory Card are

referred to as the “SD card”.

≥ Motion pictures cannot be recorded on an SD card with this unit. ≥ Please confirm the latest information on the following website. (This website is in English only.)

http://panasonic.co.jp/pavc/global/cs/e_cam

≥ This unit supports SD Memory Cards formatted in FAT12 system and FAT16 system based on SD

Memory Card Specifications and SDHC Memory Cards formatted in FAT32 system.

≥ Use this unit to format SD cards. If an SD card is formatted on other products (such as a computer),

the time spent for recording may become longer and you may not be able to use the SD card. (l 78)

≥ We recommend that you use a Panasonic brand SD card. ≥ When the write-protect switch A on SD card is locked, no recording, deletion or

editing will be possible on the card.

128 MB, 256 MB, 512 MB, 1 GB, 2GB

4GB

(SD)

≥ Keep the Memory Card out of reach of children to prevent swallowing. ≥ A MultiMediaCard cannot be used on this unit.

LSQT1157

LSQT1157_EB.book 23 ページ２００６年１２月１１日　月曜日　午後８時４６分

Before using

Disc and card handling

∫ How to hold a disc or card

Do not touch the recording/playback surface or the terminal surface.

∫ When inserting/removing a disc

Do not allow the recording/playback side of the disc to get fingerprints or dirty. ≥ If there is a scratch or dirt (e.g. dust or fingerprints) on the recording/playback side of the disc, images

cannot be recorded or played back normally and the following phenomena may occur:

jRecording or playback become impossible. jPlayback image stops momentarily or sound is interrupted during playback. jBlock noise appears on playback images. jThe message “PLEASE CHECK FOR SCRATCHES OR STAINS ON DISC.” appears.

∫ If there is dirt on the disc

Clean it with the supplied disc cleaning cloth. Wipe the disc from the centre to the outer edge to remove the dirt. Do not use force when wiping the disc as it may scratch it. Also, do not use solvents (thinner, water, antistatic agent, detergent etc.)

∫ Handling precautions ≥ Be careful about scratches and dirt. ≥ Do not attach labels or stickers to discs.

(This may cause disc warping and un-balanced rotation, rendering it unusable.)

≥ Write on the label side of the disc only with a soft, oil-based felt pen. Do not use ballpoint pens or

other hard writing implements.

≥ Do not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any other

solvent.

≥ Do not use scratch-proof protectors or covers. ≥ Do not drop, stack, or impact discs. Do not place objects on them. ≥ Do not use the following discs:

jDiscs with exposed adhesive from removed stickers or labels. jDiscs that are badly warped or cracked. jIrregularly shaped discs, such as heart shapes.

≥ Do not expose the terminals of the card to water, garbage or dust. ≥ Do not place in the following areas:

jIn direct sunlight. jIn very dusty or humid areas. jNear a heater. jLocations susceptible to significant difference in temperature (condensation can occur). jWhere static electricity or electromagnetic waves occur.

≥ Put discs and cards back in their cases for protection when not using them.

LSQT1157

LSQT1157_EB.book 24 ページ２００６年１２月１１日　月曜日　午後８時４６分

Setup

Power supply

Fitting the battery

Charging the battery

When this unit is purchased, the battery is not charged. Charge the battery before using this unit.

≥ If the DC cable is connected to the AC

adaptor, then the battery will not charge. Remove the DC cable from the AC adaptor.

1 Connect the AC cable to the AC

adaptor and the AC outlet.

2 Put the battery on the battery

mount by aligning the mark, and

then securely plug it in.

≥ The output plug of the AC cable is not

completely connected to the AC adaptor socket. As shown in A, there is a gap.

∫ Charging lamp

Lights up: Charging Goes off: Charging completed Flashing: The battery is over discharged

(discharged excessively). In a while, the lamp will light up and normal charging will start. When the battery temperature is excessively high or low, the CHARGE lamp flashes and the charging time will be longer than normal.

Push the battery against the battery holder and slide it until it clicks.

Removing the battery

While sliding the BATTERY lever, slide the battery to remove it.

≥ Hold the battery with your hand so it does not

fall.

≥ Before removing the battery, be sure to set the

OFF/ON switch to OFF and check that the status indicator is off.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

≥ Battery charging time (l 25) ≥ We recommend using Panasonic batteries.

(l 10, 11)

≥ If you use other batteries, we cannot guarantee

the quality of this product.

LSQT1157

LSQT1157_EB.book 25 ページ２００６年１２月１１日　月曜日　午後８時４６分

Setup

Charging time and recordable time

The times shown in the tables below are for when the temperature is 25 oC and the humidity is 60%. If the temperature is higher or lower than 25 oC, the charging time will become longer.

∫ Charging time ≥ The charging time shown in the table are approximations.

≥ “2 h 25 min” indicates 2 hours 25 minutes.

VDR-D310:

Battery model number Voltage/capacity Charging time

Supplied battery/

CGA-DU12 (optional)

CGA-DU14 (optional) 7.2 V/1360 mAh 2 h 45 min

CGA-DU21 (optional) 7.2 V/2040 mAh 3 h 55 min

VDR-D220:

Battery model number Voltage/capacity Charging time

Supplied battery/

CGR-DU06 (optional)

CGA-DU12 (optional) 7.2 V/1150 mAh 2 h 25 min

CGA-DU14 (optional) 7.2 V/1360 mAh 2 h 45 min

CGA-DU21 (optional) 7.2 V/2040 mAh 3 h 55 min

7.2 V/1150 mAh 2 h 25 min

7.2 V/640 mAh 1 h 40 min

LSQT1157

LSQT1157_EB.book 26 ページ２００６年１２月１１日　月曜日　午後８時４６分

Setup

∫ Recordable time (When using a DVD-RAM disc) ≥ The times indicate the recordable time when the viewfinder is used. The times in parentheses

indicate the recordable time when the LCD monitor is used.

≥ The actual recordable time refers to the recordable time on a disc when repeatedly starting/stopping

recording, turning the unit on/off, moving the zoom lever, etc.

≥ “1 h 25 min” indicates 1 hour 25 minutes.

VDR-D310:

Battery model

number

Supplied

battery/

CGA-DU12

(optional)

CGA-DU14

(optional)

CGA-DU21

(optional)

Voltage/

capacity

7.2 V/

1150 mAh

7.2 V/

1360 mAh

7.2 V/

2040 mAh

Recording

mode

Maximum

continuously

recordable time

1h25min

(1 h 20 min)

1h40min

(1 h 30 min)

1h45min

(1 h 40 min)

1h45min

(1 h 40 min)

(1 h 50 min)

2h5min

(1 h 55 min)

2h50min

(2 h 40 min)

3h10min

(3 h)

3h20min

(3h5min)

Actual recordable

time

35 min

(35 min)

45 min

(40 min)

45 min

(45 min)

45 min

(45 min)

50 min

(50 min)

55 min

(50 min)

1h15min

(1 h 10 min)

1h25min

(1 h 20 min)

1h30min

(1 h 20 min)

VDR-D220:

Battery model

number

Supplied

battery/

CGR-DU06

(optional)

CGA-DU12

(optional)

Voltage/

capacity

7.2 V/

640 mAh

7.2 V/

1150 mAh

Recording

mode

Maximum

continuously

recordable time

1h5min

(1 h)

1h20min

(1 h 10 min)

1h25min

(1 h 15 min)

(1 h 50 min)

2h20min

(2 h 10 min)

2h30min

(2 h 15 min)

Actual recordable

time

30 min

(25 min)

35 min

(30 min)

35 min

(30 min)

55 min

(50 min)

(55 min)

1h5min

(1 h)

LSQT1157

LSQT1157_EB.book 27 ページ２００６年１２月１１日　月曜日　午後８時４６分

Setup

Battery model

number

CGA-DU14

(optional)

CGA-DU21

(optional)

Voltage/

capacity

7.2 V/

1360 mAh

7.2 V/

2040 mAh

Recording

mode

Maximum

continuously

recordable time

2h35min

(2 h 20 min)

(2 h 40 min)

3h10min

(2 h 50 min)

3h50min

(3 h 30 min)

4h30min (4h5min)

4h45min

(4 h 20 min)

Actual recordable

time

1h5min

(1 h)

1h20min

(1 h 10 min)

1h25min

(1 h 15 min)

1h40min

(1 h 35 min)

(1 h 50 min)

2h5min

(1 h 55 min)

≥ The display changes as the battery capacity reduces.

####.

If the battery discharges, then ( ) will flash.

≥ The recordable times will vary depending on the status of use. These times are approximations. The

recordable time will become shorter when you use both the viewfinder and the LCD monitor simultaneously while rotating the LCD monitor frontward to record yourself, etc.

≥ The batteries heat up after use or charging. This unit will also heat up while being used. This is not a

malfunction.

≥ Be aware that the operating time of the battery will become shorter in low temperatures. We

recommend charging a spare battery for use when recording.

LSQT1157

LSQT1157_EB.book 28 ページ２００６年１２月１１日　月曜日　午後８時４６分

Setup

Connecting to the AC outlet

The unit is in the standby condition when the AC adaptor is connected. The primary circuit is always “live” as long as the AC adaptor is connected to an electrical outlet.

1 Connect the AC cable to the AC

adaptor and the AC outlet.

2 Connect the DC cable to the AC

adaptor.

3 Connect the DC cable to this unit.

How to turn on the power

While pressing the button A, set the OFF/ON switch to ON.

The status indicator B lights and the power turns on. ≥ When the unit is turned on for the first time, a

message asking you to set the date and time will appear. Select [YES] and set the date and time. (l 38)

How to turn off the power

While pressing the button A, set the OFF/ON switch to OFF.

≥ Do not use the AC cable with any other

equipment as it is designed only for this unit. Do not use the AC cable from other equipment with this unit.

≥ While the DC cable is connected to the AC

adaptor, the battery will not charge.

Turning the unit on/off

≥ When recording, remove the lens cap before

turning the unit on. If the unit is turned on with the lens cap attached, the automatic white balance adjustment (l 102) may not function properly.

LSQT1157

The status indicator B goes off when the power turns off.

LSQT1157_EB.book 29 ページ２００６年１２月１１日　月曜日　午後８時４６分

∫ To turn off the power

When the power is turned on for the first time after changing the disc or battery, the unit carries out a recognition procedure to check that there are no problems with the disc. This takes approximately 25 seconds with DVD-RAM. If you want to start using the unit as soon as you turn on the power, do the following.

1) Turn on the power.

2) After “READING DISC...” disappears from the screen, turn off the power.

You can start recording approximately 8 seconds after you turn on the power again. ≥ Depending on the condition of the disc, it

may take longer than this.

≥ If the date and time are not set, it will take

longer than usual before you can start recording.

Close the LCD monitor and retract the viewfinder.

The status indicator goes off and the power turns off. ≥ The power will not turn off unless the LCD

monitor is closed and the viewfinder is retracted.

≥ The power will not turn off while recording on a

disc even if the LCD monitor is closed and the viewfinder is retracted.

Setup

How to turn the power on and off with the LCD monitor/viewfinder

When the OFF/ON switch is set to ON, the power can be turned on and off with the LCD monitor and the viewfinder when the unit is in video recording mode or picture recording mode.

∫ To turn on the power Open the LCD monitor or extend the

viewfinder.

The status indicator lights and the power turns on.

Set the OFF/ON switch to OFF when the unit is not being used.

Inserting/removing a disc

When inserting or removing the disc, fit the charged battery pack or connect the AC adaptor to the unit. The cover of the disc compartment will not open unless the unit is powered.

1 Fit the battery or connect the AC

adaptor.

2 Slide the DISC EJECT lever once

and release it.

LSQT1157

LSQT1157_EB.book 30 ページ２００６年１２月１１日　月曜日　午後８時４６分

Setup

A few moments after the ACCESS/PC lamp blinks, the cover of the disc compartment will open slightly.

3 Open the cover of the disc

compartment by hand and insert/ remove the disc.

∫ Inserting disc

Fit the disc onto the spindle in the centre and then push the disc down until it clicks into place.

A Recording/playback side B Pickup lens

∫ Removing disc

While pressing down on the spindle, grasp the edge of the disc and gently lift it out.

≥ Take care not to touch the recording/playback

sides of a disc when inserting or removing it.

LSQT1157

4 Push the section marked

PUSH CLOSE on the cover of the disc compartment to close the cover.

≥ If you use a new DVD-RW, it is necessary to

format the disc. (l 21)

∫ Identifying recording/playback sides of

disc

Single sided disc:

The recording/playback side is opposite to the labelled side.

Double sided disc:

The “SIDE A” recording/playback side is the side opposite the side with the “SIDE A” mark. The

+ 82 hidden pages