Panasonic TH-65PF10WK, TH-50PF10WK User Manual

Operating Instructions

High Deﬁ nition Plasma Display

Model No.

TH-50PF10WK TH-65PF10WK

The illustration shown is an image.

Please read these instructions before operating your set and retain them for future reference.

English

TQBC2236

Dear Panasonic Customer

Welcome to the Panasonic family of customers. We hope that you will have many years of

enjoyment from your new Plasma Display.

To obtain maximum benefit from your set, please read these Instructions before making

any adjustments, and retain them for future reference.

Retain your purchase receipt also, and note down the model number and serial number of

your set in the space provided on the rear cover of these instructions.

Visit our Panasonic Web Site http://panasonic.net

Table of Contents

Important Safety Notice ........................................... 3

Safety Precautions ................................................... 4

Accessories .............................................................. 7

Accessories Supply ................................................. 7

Remote Control Batteries ........................................ 7

Connections .............................................................. 8

PC Input Terminals connection .............................. 10

SERIAL Terminals connection ............................... 11

HDMI connection ................................................... 12

COMPONENT / RGB connection .......................... 12

Power On / Off ......................................................... 13

Initial selections ..................................................... 15

Selecting the input signal ...................................... 15

Selecting the On-Screen Menu Language ............ 15

Basic Controls ........................................................ 16

On-Screen Menu Displays ..................................... 18

ASPECT Controls ................................................... 20

Adjusting Pos. /Size ............................................... 21

MULTI PIP ................................................................ 23

Advanced PIP .......................................................... 24

Picture Adjustments ............................................... 25

Advanced settings ................................................. 26

Sound Adjustment .................................................. 27

SDI soud Output .................................................... 28

SURROUND .......................................................... 28

Mute ...................................................................... 28

Digital Zoom ............................................................ 29

PRESENT TIME Setup / Set up TIMER .................. 30

PRESENT TIME Setup .......................................... 30

Set up TIMER ........................................................ 31

Screensaver (For preventing image retention) .... 32

Setup of Screensaver Time ................................... 33

Reduces screen image retention ........................... 33

Side Panel Adjustment .......................................... 34

Reduces power consumption ............................... 35

Customizing the Input labels ................................. 35

Setup for MULTI DISPLAY ...................................... 36

How to Setup MULTI DISPLAY ............................. 36

How to set the display location number

for each Plasma Display ....................................... 37

ID Remote Control Function .................................. 38

Set up for Portrait ................................................... 39

How to setup Portrait ............................................. 39

Setup for Input Signals .......................................... 41

Component / RGB-in select ................................... 41

3D Y/C Filter .......................................................... 41

P-NR / Block NR / Mosquito NR ............................ 42

Refresh Rate ......................................................... 42

Colour system / Panasonic Auto ........................... 43

Cinema reality ....................................................... 43

Sync ...................................................................... 44

H-Freq. (kHz) / V-Freq. (Hz) .................................. 44

Options Adjustments ............................................. 45

Weekly Command Timer ....................................... 49

Shipping condition ................................................. 51

Troubleshooting ..................................................... 52

COMPONENT/RGB/PC/VIDEO input signals ........ 53

Command list of Weekly Command Timer. .......... 55

Speciﬁ cations ......................................................... 56

Important Safety Notice

WARNING

1) To prevent damage which may result in ﬁ re or shock hazard, do not expose this appliance to dripping or splashing.

Do not place containers with water (ﬂ ower vase, cups, cosmetics, etc.) above the set. (including on

shelves above, etc.)

No naked ﬂ ame sources, such as lighted candles, should be placed on / above the set.

2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualiﬁ ed service personnel.

3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three pin earthing-type power plug. This plug will only ﬁ t an earthing-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician.

Do not defeat the purpose of the earthing plug.

4) To prevent electric shock, ensure the earthing pin on the AC cord power plug is securely connected.

CAUTION

This appliance is intended for use in environments which are relatively free of electromagnetic ﬁ elds. Using this appliance near sources of strong electromagnetic ﬁ elds or where electrical noise may overlap with the input signals could cause the picture and sound to wobble or cause interference such as noise to appear. To avoid the possibility of harm to this appliance, keep it away from sources of strong electromagnetic ﬁ elds.

Trademark Credits

• VGA is a trademark of International Business Machines Corporation.

• Macintosh is a registered trademark of Apple Computer, USA.

• S-VGA is a registered trademark of the video Electronics Standard Association. Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.

• HDMI, the HDMI logo and High-Deﬁ nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

Note:

Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.

Safety Precautions

WARNING

Setup

This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury.

(All of the following accessories are manufactured by Matsushita Electric Industrial Co., Ltd.)

• Speakers .....................................................TY-SP50P8W-K (TH-50PF10WK), TY-SP65P10WK (TH-65PF10WK)

• Pedestal ...................................................... TY-ST07-K (TH-50PF10WK), TY-ST08-K (TH-50PF10WK),

TY-ST65-K (TH-65PF10WK)

• Mobile stand ................................................ TY-ST42PF3 (TH-50PF10WK), TY-ST58PF10 (TH-50PF10WK)

• Wall-hanging bracket (vertical) .................... TY-WK65PV7 (TH-65PF10WK)

• Wall-hanging bracket (angled) .................... TY-WK42PR7 (TH-50PF10WK), TY-WK65PR8 (TH-65PF10WK)

• Wall-hanging bracket (drawer type) ............ TY-WK42DR1 (TH-50PF10WK)

• Ceiling-hanging bracket ..............................TY-CE42PS7 (TH-50PF10WK)

• BNC Component Video Terminal Board ......TY-42TM6A

• BNC Composite Video Terminal Board .......TY-42TM6B

• BNC Dual Video Terminal Board ................. TY-FB9BD

• DVI-D Terminal Board for PF Series ........... TY-FB9FDD

• RCA Component Video Terminal Board ......TY-42TM6Z

• RCA Composite Video Terminal Board .......TY-42TM6V

• RGB Active Through Terminal Board ..........TY-42TM6G

• PC Input Terminal Board .............................TY-42TM6P

•

Composite / Component Video Terminal Board

• SDI Terminal Board .....................................TY-FB7SD

• HD-SDI Terminal Board ............................... TY-FB9HD

• HDMI Terminal Board .................................. TY-FB8HM

• Ir Through Terminal Board ..........................TY-FB9RT

• HD-SDI Terminal Board with audio .............TY-FB10HD

• Dual HDMI Terminal Board .........................TY-FB10HMD

• Wireless Presentation Board ....................... TY-FB10WPE

• AV Terminal Box .......................................... TY-TB10AV

• Touch Panel ................................................TY-TP50P10S (TH-50PF10WK), TY-TP65P10S (TH-65PF10WK)

• Anti glare ﬁ lter .............................................TY-AR50P9W (TH-50PF10WK), TY-AR65P9W (TH-65PF10WK)

... TY-42TM6Y

Always be sure to ask a qualiﬁ ed technician to carry out set-up.

Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from being played with by young children, creating the potential risk of suffocation.

Do not place the Plasma Display on sloped or unstable surfaces.

• The Plasma Display may fall off or tip over.

Do not place any objects on top of the Plasma Display.

• If water is spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in ﬁ re or electric shock. If any foreign objects get inside the Plasma Display, please consult your local Panasonic dealer.

Transport only in upright position!

• Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry.

Ventilation should not be impleded by covering the ventilation openings with items such as newspapers, table cloths and curtains.

For sufﬁ cient ventilation; If using the pedestal (optional accessory) for the Plasma Display, leave a space of at least 10 cm at the top, left and right, at least 6 cm at the bottom, and at least 7 cm at the rear. If using some other setting-up method, leave a space of at least 10 cm at the top, bottom, left and right, and at least 7 cm at the rear.

Safety Precautions

When using the Plasma Display

The Plasma Display is designed to operate on 220 - 240 V AC, 50/60 Hz.

Do not cover the ventilation holes.

• Doing so may cause the Plasma Display to overheat, which can cause ﬁ re or damage to the Plasma Display.

Do not stick any foreign objects into the Plasma Display.

• Do not insert any metal or ﬂ ammable objects into the ventilations holes or drop them onto the Plasma Display, as doing so can cause ﬁ re or electric shock.

Do not remove the cover or modify it in any way.

• High voltages which can cause severe electric shocks are present inside the Plasma Display. For any inspection, adjustment and repair work, please contact your local Panasonic dealer.

Ensure that the mains plug is easily accessible.

Do not use any power supply cord other than that provided with this unit.

• Doing so may cause ﬁ re or electric shocks.

Securely insert the power supply plug as far as it will go.

• If the plug is not fully inserted, heat may be generated which could cause ﬁ re. If the plug is damaged or the wall socket is loose, they shall not be used.

Do not handle the power supply plug with wet hands.

• Doing so may cause electric shocks.

Do not do anything that may damage the power cable. When disconnecting the power cable, pull on the plug body, not the cable.

• Do not damage the cable, make any modiﬁ cations to it, place heavy objects on top of it, heat it, place it near any hot objects, twist it, bend it excessively or pull it. To do so may cause ﬁ re and electric shock. If the power cable is damaged, have it repaired at your local Panasonic dealer.

If the Plasma Display is not going to be used for any prolonged length of time, unplug the power supply plug from the wall outlet.

If problems occur during use

If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out from the Plasma Display, immediately unplug the power supply plug from the wall outlet.

• If you continue to use the Plasma Display in this condition, ﬁ re or electric shock could result. After checking that the smoke has stopped, contact your local Panasonic dealer so that the necessary repairs can be made. Repairing the Plasma Display yourself is extremely dangerous, and shall never be done.

If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet becomes damages, disconnect the power supply plug immediately.

• A short circuit may occur, which could cause ﬁ re. Contact your local Panasonic dealer for any repairs that need to be made.

Safety Precautions

CAUTION

When using the Plasma Display

Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.

• Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result.

Be sure to disconnect all cables before moving the Plasma Display.

• If the Plasma Display is moved while some of the cables are still connected, the cables may become damaged, and ﬁ re or electric shock could result.

Disconnect the power supply plug from the wall socket as a safety precaution before carrying out any cleaning.

• Electric shocks can result if this is not done.

Clean the power cable regularly to prevent it becoming dusty.

• If dust built up on the power cord plug, the resultant humidity can damage the insulation, which could result in ﬁ re. Pull the power cord plug out from the wall outlet and wipe the mains lead with a dry cloth.

This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment. Install your infrared sensor in a place away from direct or reﬂ ected light from your Plasma Display.

Cleaning and maintenance

The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth.

• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry.

• Do not scratch or hit the surface of the panel with ﬁ ngernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected.

If the cabinet becomes dirty, wipe it with a soft, dry cloth.

• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.

• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get inside the unit, operating problems may result.

• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contact with articles made from rubber or PVC.

Accessories

Accessories Supply

Check that you have the accessories and items shown

Operating Instruction book

Power supply cord Fixing bands × 2

Remote Control Transmitter EUR7636070R

Batteries for the Remote Control Transmitter (2 × R6 (UM3) Size)

Remote Control Batteries

Requires two R6 batteries.

1. Pull and hold the hook, then open the battery cover.

2. Insert batteries - note correct polarity ( + and -).

“R6 (UM3)” size

Helpful Hint:

For frequent remote control users, replace old batteries with Alkaline batteries for longer life.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Disposal of batteries should be in an environment-friendly manner.

Observe the following precaution:

1. Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.

2. Do not combine a used battery with a new one.

3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.

3. Replace the cover.

Connections

TH-50PF10WK

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

Speakers (Optional accessories)

Speaker

terminal (L) Speaker terminal (R)

– AC cord ﬁ xing

Note:

Make sure that the AC cord is locked on both the left and right sides.

– Cable ﬁ xing bands Secure any excess cables with bands as required.

Pass the attached cable ﬁ xing band through the clip as shown in the ﬁ gure.

To secure cables connected to Terminals, wrap the cable ﬁ xing band around them then pass the pointed end through the locking block, as shown in the ﬁ gure.

While ensuring there is sufﬁ cient slack in cables to minimize stress (especially in the power cord), ﬁ rmly bind all cables with the supplied ﬁ xing band.

AC cord connection (see page 13)

Plug the AC cord into the display unit.

Plug the AC cord until it clicks.

Unplug the AC cord

Unplug the AC cord pressing the two knobs.

Note:

When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet ﬁ rst.

To tighten: To loosen:

Pull

SLOT1 SLOT3

Optional Terminal Board Insert Slot (covered)

Note: At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3.

Dual HDMI Terminals (equivalent of Dual HDMI Terminal Board (TY-FB10HMD)) (see page 12)

SLOT2

AUDIO

R L

COMPONENT/RGB IN and Audio IN Terminals (equivalent of BNC Component Video Terminal Board (TY-42TM6A)) (see page 12)

P R /C R /R P B /C B /B

COMPONENT/RGB IN

Y/G

From EXTERNAL monitor terminal on Computer (see page 10)

Push the catch

Pull

AUDIO

SERIAL PC IN

From SERIAL Terminal on Computer (see page 11)

TH-65PF10WK

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

Speakers (Optional accessories)

Connections

Speaker terminal (R)

AC cord connection (see page 13)

– AC cord ﬁ xing

Plug the AC cord

into the display unit.

Plug the AC cord

until it clicks.

Fix the AC

Note:

Make sure that the AC cord is locked on both the left and right sides.

– Cable ﬁ xing bands Secure any excess cables with bands as required.

Pass the attached cable ﬁ xing band through the clip as shown in the ﬁ gure.

cord with the clamper which is attached to the unit.

To secure cables connected to Terminals, wrap the cable ﬁ xing band around them then pass the pointed end through the locking block, as shown in the ﬁ gure.

While ensuring there is sufﬁ cient slack in cables to minimize stress (especially

Open

in the power cord), ﬁ rmly bind all cables with the supplied ﬁ xing band.

Speaker terminal (L)

Push until the hook clicks.

2. Pull off.

Keep the

knob pressed.

Unplug the AC cord

Unplug the AC cord pressing the two knobs.

Note:

When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet ﬁ rst.

To tighten:

Pull

SLOT1 SLOT3

Optional Terminal Board Insert Slot (covered)

Dual HDMI Terminals (equivalent of Dual HDMI Terminal Board (TY-FB10HMD)) (see page 12)

AUDIO

R L

SLOT2

COMPONENT/RGB IN and Audio IN Terminals (equivalent of BNC Component Video Terminal Board (TY-42TM6A)) (see page 12)

P R /C R /R P B /C B /B

COMPONENT/RGB IN

Note:

At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3.

To loosen: Push the catch

Y/G

From EXTERNAL monitor terminal on Computer (see page 10)

Pull

AUDIO

SERIAL PC IN

From SERIAL Terminal on Computer (see page 11)

Connections

PC Input Terminals connection

COMPUTER

TH-42PS9

Conversion adapter (if necessary)

RGB

PC cable

AUDIO

PC IN

Mini D-sub 15p

Audio

Connect a cable which matches the audio output terminal on the computer.

Stereo plug

Notes:

• Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input Terminal.

• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

• The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080 dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show ﬁ ne detail with sufﬁ cient clarity.

• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

• Some PC models cannot be connected to the set.

• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

• The computer shown in the illustration is for example purposes only.

• Additional equipment and cables shown are not supplied with this set.

• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speciﬁ ed frequency range.

• Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.

• Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”

(when Component signal connection) or “RGB” (when RGB signal connection). (see page 41)

Signal Names for Mini D-sub 15P Connector

Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name

15 14 13 12 11

Pin Layout for PC Input Terminal

67839

R (PR/CR)

B (PB/CB)

NC (not connected)

GND (Ground)

G (Y)

GND (Ground)

+5 V DC

GND (Ground)

NC (not connected)

HD/SYNC

SDA

SCL

SERIAL Terminals connection

The SERIAL terminal is used when the Plasma Display is controlled by a computer.

Connections

COMPUTER

RS-232C Straight cable

SERIAL

Pin layout for SERIAL Terminal

13452

6789

D-sub 9p

Notes:

• Use the RS-232C cable to connect the computer to the Plasma Display.

• The computer shown is for example purposes only.

• Additional equipment and cables shown are not supplied with this set.

The SERIAL terminal conforms to the RS-232C interface speciﬁ cation, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisﬁ es the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details.

Communication parameters

Signal level RS-232C compliant

Synchronization method Asynchronous

Baud rate 9600 bps

Parity None

Character length 8 bits

Stop bit 1 bit

Flow control -

D-sub 9-pin female Details

RS-232C Conversion cable

2 3 5

• 7 8

•

R X D T X D

GND

Non use

Shorted

Basic format for control data

The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent.

STX C1 C2 C3 P1 P2 P3 P4: P5 ETX

Start (02h)

Colon Parameter(s) 3-character command (3 bytes)

(1 - 5 bytes)

End (03h)

Notes:

• If multiple commands are transmitted, be sure to wait for the response for the ﬁ rst command to come from this unit before sending the next command.

• If an incorrect command is sent by mistake, this unit will send an “ER401” command back to the computer.

• SL1A, SL1B, SL2A and SL2B of Command IMS are available only when a dual input terminal board is attached.

Command

Command Parameter Control details PON None Power ON POF None Power OFF AVL ** Volume 00 - 63

AMT

IMS None

DAM None

0 Audio MUTE OFF 1 Audio MUTE ON

Input select (toggle) SL1 SL2 SL3 PC1 SL1A SL1B SL2A SL2B

NORM ZOOM FULL JUST SELF

Slot1 input

Slot2 input

Slot3 input

PC input

Slot1 input (INPUT1A)

Slot1 input (INPUT1B)

Slot2 input (INPUT2A)

Slot2 input (INPUT2B)

Screen mode select (toggle)

NORMAL (4 : 3)

ZOOM

FULL

JUST

Panasonic AUTO

With the power off, this display responds to PON command only.

Connections

HDMI connection

This unit has terminal boards equivalent to Dual HDMI Terminal Board (TY-FB10HMD) and BNC Component Video Terminal Board (TY-42TM6A) as standard equipment.

[Pin assignments and signal names]

Pin No.

3 4

6 7

Signal

T.M.D.S Data2+

T.M.D.S Data2 Shield

T.M.D.S Data2T.M.D.S Data1+ T.M.D.S Data1

Shield T.M.D.S Data1T.M.D.S Data0+ T.M.D.S Data0

Shield T.M.D.S Data0T.M.D.S Clock+

Pin No.

T.M.D.S Clock

Shield

T.M.D.S Clock-

CEC

Reserved

(N.C. on device)

SCL

SDA DDC/CEC

Ground

+5V Power

Hot Plug Detect

Signal

AUDIO

SLOT1 SLOT2 SLOT3

PR/CR/R PB/CB/B

COMPONENT/RGB IN

Y/G

HDMI cables

Note:

Additional equipment and HDMI cables shown are not supplied with this set.

COMPONENT / RGB connection

COMPONEN T VIDEO OUT

B , P R ,

OUT

AUDIO

OUT

P B

Example of input signal source

DVD

Digital TV-SET-TOP-BOX (DTV-STB)

Y , P

HDMI

AV OUT

HDMI

AV OUT

DVD player DVD player

RCA-BNC adapter plug

Computer

RGB Camcorder

Notes:

• Change the “Component/RGB-in select” setting in the “Setup” menu to “Component” (when Component signal connection) or “RGB” (when RGB signal connection). (see page 41)

• Additional equipment, cables and adapter plugs shown are not supplied with this set.

• Sync on G signal is needed. (see page 44)

AUDIO

R L

P R /C R /R P B /C B /B

COMPONENT/RGB IN

SLOT3

Y/G

Power On / Off

Connecting the AC cord plug to the Plasma Display.

Fix the AC cord plug securely to the Plasma Display with the clamper. (see page 8, 9)

TH-50PF10WK TH-65PF10WK

Connecting the plug to the Wall Outlet

Notes:

• Main plug types vary between countries. The power plug shown at right may, therefore, not be the type ﬁ tted to your set.

• When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet ﬁ rst.

Press the Power switch on the Plasma Display to turn the set on: Power-On.

INPUT MENU ENTER/ +/ VOL -/

Power Indicator

Power Indicator: Green

Example: The screen below is displayed for a while after the

Plasma Display is turned on (setting condition is an example).

When the Power is turned on for the ﬁ rst time, the Language selection screen is displayed.

From the second time on, language selection can be done from the setup menu. (see page 15)

OSD Language

English (UK)

Deutsch

Français

Italiano

Español

ENGLISH (US)

Select the desired language using the or button and press the ACTION ( )

Русский

button.

Note:

SetSelect

Set with the remote control. Buttons on the main unit are unavailable for this setting.

Remote Control Sensor

From the second time on, the below screen is displayed for a while (setting condition is an example).

16:9

Power On / Off

Press the button on the remote control to turn the Plasma Display off.

Power Indicator: Red (standby)

Press the

Power Indicator: Green

Turn the power to the Plasma Display off by pressing the switch on the unit, when the Plasma Display is on or in standby mode.

Note:

During operation of the power management function, the power indicator turns orange in the power off state.

button on the remote control to turn the Plasma Display on.

INPUT MENU ENTER/ + / VOL - /

Initial selections

Selecting the input signal

Select the input signals to be connected by installing the optional Terminal Boards.

Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display.

Input signals will change as follows:

INPUT1 INPUT2 PCINPUT3

Press the INPUT “1”, “2”, “3” or “PC” input mode selection button to select the input mode. This button is used to switch directly to INPUT mode. These buttons can only display the slot which is installed. If you press the button whose slot is not installed, it automatically displays the current input signal. When a dual input terminal board is attached, A or B is displayed depending on the selected input signal. (Ex. INPUT1A, INPUT1B)

Notes:

• Selecting is also possible by pressing the INPUT button on the unit.

• Input terminal will not be selected if the terminal board is not installed into the SLOT.

• Select to match the signals from the source connected to the component/RGB input terminals. (see page 41)

• In 2 screen display, the same input mode cannot be selected for the main picture and sub picture.

• Image retention (image lag) may occur on the plasma display panel when a still picture is kept on the panel for an extended period. The function that darkens the screen slightly is activated to prevent image retention (see page 52), but this function is not the perfect solution to image retention.

INPUT MENU ENTER/ + / VOL - /

Selecting the On-Screen Menu Language

Press to display the Setup menu.

Press to select the OSD Language.

Press to select your preferred language.

Selectable languages

English(UK)

Deutsch

Français

Italiano

Español

ENGLISH(US)

.......(Chinese)

.......(Japanese)

Русский

.......(Russian)

Setup

Component/RGB-in select

Input label

Power save Standby save Power management Auto power off OSD Language English (UK

1/2

Signal

RGB

PC Off Off Off Off

)

INPUT MENU ENTER/

/VOL

Basic Controls

Main Unit

Remote control sensor

Main Power On / Off Switch

Power Indicator

The Power Indicator will light.

• Power-OFF ....Indicator not illuminated (The unit will

still consume some power as long as the power cord is still inserted into the wall outlet.)

• Standby ......... Red

• Power-ON ......Green

• DPMS .............Orange (With PC input signal and during

operation of PC’s screensaver.)

Volume Adjustment

Volume Up “+” Down “–” When the menu screen is displayed: “+” : press to move the cursor up “–” :

press to move the cursor down

(see page 18)

Enter / Aspect button

(see page 18, 20)

MENU Screen ON / OFF

Each time the MENU button is pressed, the menu screen will switch. (see page 18)

Normal Viewing PICTURE SET UP

SOUND POS. /SIZE

INPUT button (INPUT1, INPUT2, INPUT3 and PC selection)

(see page 15)

Remote Control Transmitter

Basic Controls

R button (see page 19)

Press the R button to return to previous menu screen.

Standby (ON / OFF) button

The Plasma Display must ﬁ rst be plugged into the wall outlet and turned on at the power switch (see page 13, 14). Press ON to turn the Plasma Display On, from Standby mode. Press OFF to turn the Plasma Display Off to Standby mode.

N button (see page 21, 22, 25, 26, 27)

POSITION buttons

ACTION button

Press to make selections.

POS. /SIZE button

(see page 21)

PICTURE button (see page 25)

INPUT button (INPUT1, INPUT2, INPUT3 and PC selection)

Press to select INPUT1, INPUT2, INPUT3 and PC input SLOTS sequentially. (see page 15)

Sound mute On / Off (see page 28)

Numeric buttons (see page 38)

ASPECT button

Press to adjust the aspect. (see page 20)

MULTI Window buttons (see page 23)

Status button

Press the “Status” button to display the current system status.

Input label

Aspect mode (see page 20)

Off timer

The off timer indicator is displayed only when the off timer has been set.

4:3

Off timer 90

SET UP button (see page 18, 19)

SOUND button (see page 27)

DIRECT INPUT buttons

Press the INPUT “1”, “2”, “3” or “PC” input mode selection button to select the INPUT mode. (see page 15) This button is used to switch directly to INPUT mode.

Channel Adjustment

This button cannot be used for this model.

Volume Adjustment

Press the Volume Up “+” or Down “–” button to increase or decrease the sound volume level.

OFF TIMER button

The Plasma Display can be preset to switch to stand-by after a ﬁ xed period. The setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed.

30 60

When three minutes remain, “OFF TIMER 3” will ﬂ ash. The off timer is cancelled if a power interruption occurs.

Digital Zoom (see page 29)

Remote ID lock (see page 38)

SURROUND button

(see page 28) The surround setting switches on and off each time the SURROUND button is pressed. The beneﬁ ts of surround sound are enormous. You can be completely enveloped in sound; just as if you were at a concert hall or cinema.

INPUT MENU ENTER/+/VOL-/

On-Screen Menu Displays

To Picture adjust menu (see page 25)

Normalise

Picture Mode Contrast Brightness Colour Hue Sharpness

White balance Colour Management Advanced settings

Normal

0 0 0 5

1/2 Picture

2/2Picture

Normal

Off On

The MENU button on the unit can also be pressed.

Each time the MENU button is pressed, the menu screen will switch.

Press to select “On”.

Press to enter Advanced settings.

To Advanced settings (see page 25, 26)

Advanced settings

Normalise

Black extension Input level Gamma AGC

Advanced settings

W/B High R W/B High G W/B High B W/B Low R W/B Low G W/B Low B

Normal

1/2

0 0

2.2 Off

2/2

0 0 0 0 0 0

To Pos. /Size adjust menu (see page 21) During “Video (S Video)”, “Digital”,

“SDI” and “HDMI” input signal.

Pos. /Size

Normalise

Auto Setup

Normal

H-Pos H-Size V-Pos V-Size 1:1 Pixel Mode

0 0 0 0

Off

During “Component”, “RGB” and “PC” input signal.

Pos. /Size

Normal Viewing Picture Setup

Sound Pos. /Size

Normalise

Auto Setup

Normal

H-Pos H-Size V-Pos V-Size Dot Clock

Clock Phase

1:1 Pixel Mode

0 0 0 0 0 0

Off

Press to select.

[ from the unit ]

Press to select.

Press to access each adjust

screen.

Setup

Component/RGB-in select

Input label

Power save Standby save Power management Auto power off OSD Language English (UK

Signal

RGB

PC Off Off Off Off

Screensaver

MULTI DISPLAY Setup

Portrait Setup Set up TIMER

PRESENT TIME Setup

To Sound adjust menu (see page 27)

Sound

Normalise

Sound Mode Bass Mid Treble Balance Surround Audio Out (PIP)

Normal

1/2

Normal 0 0 0 0

Off

Main

When HD-SDI Terminal Board with audio (TY-FB10HD) is installed

SDI Sound Output

Left Channel Right Channel Sound Out Level Meter

2/2

Channel 1 Channel 1

Off Off

1/2

)

2/2 Setup

+ 42 hidden pages