Panasonic TH-50PHD3VE, TH-50PHD5VBX, TH-50PHD3VU, TH-50PHD5VUY, TH-42PWD4VBX User Manual

...
Plasma Display
Installation
Instructions
TH-50PHD3V TH-50PH30V TH-50PHD5V TH-42PWD4V TH-42PWD5V
Before attempting to install this model,
Operation method of plasma display, please see the
Operation Manual for the TH-50PHD3,
TH-50PHD30,TH-50PHD5, TH-42PWD4,
TH-42PWD5.
TQZH330-1
Model No.
Model No.
2
Thank you very much for purchasing the Plasma Display.
Installation work should only be carried out by a qualified technician.
If the unit is installed incorrectly, the display may fall down and personal injury may result.
Precautions with regard to setting up
WARNING
Always have a service technician perform the installation.
The internal components of the display may be hot and cause burns. If the product is not correctly installed and adjusted, damage may result to the product.
Make sure that all safety factors regarding strength of installation are observed.
If the installation strength is insufficient, the display may fall down and personal injury may result.
Do not install in places which are unable to bear loads.
If the strength of the installation surface is insufficient, the display may fall down and personal injury may result.
Caution
Do not install in places which are subject to humidity, dust, oil fumes, water vapor or excessive heat.
These can have adverse effects on Plasma Display operation, and fire or electric shocks may result.
Two people are required to install and remove the display.
If two people are not present, the display may be dropped, and personal injury may result.
Maintain a space of at least 10 cm (3
15
/16inch) at the top, bottom and sides of the display,
and at least 1.9 cm (
3
/4inch) at the rear of the display.
The display has air outlet holes at the top and air intake holes at the bottom and rear. These holes must not be covered, otherwise fire may result.
3
Components
Points to note during installation
This model is for the Plasma Display. Do not use this model for any other purpose.
In order to ensure correct, problem-free operation of the Plasma Display, do not
install the Display in any of the following places.
Places which are next to sprinklers or sensors
Places which are subject to vibration or shocks
Places which are close to high-voltage wires or electric motors
Places in direct contact with air from heaters
When installing the wall-hanging bracket unit, use a mounting method appropriate
to the type of wall.
This model does not include the bolts needed to mount the bracket to the wall.
Please purchase screws suitable for the material (wood, steel frame, concrete, etc.) of the wall on which the bracket and Plasma Display are to be mounted.
Insert the power cord plug for the Plasma Display into a wall outlet which is close
and easily accessible.
Provide adequate ventilation so that the temperature around the display does not rise above 40. If there is insufficient movement of air inside the display, heat
may build up inside the display, and fire may result.
This Plasma Display is for use only with the following optional accessories.
Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of following accessories are manufactured by Matsushita Electric Industrial Co., Ltd.)
Wall-hanging bracket (vertical) --- TY-WK42PV1
Wall-hanging bracket (for PDP with PC) --- TY-WK42PRE1 (for U.S.A only)
Always be sure to ask a qualified technician to carry out set-up.
Make sure that you have the following accessory.
There is following accessory in addition to the accessories indicated by the TH­50PHD3, TH-50PHD30, TH-50PHD5, TH-42PWD4, TH-42PWD5 operating instructions.
Fixing screw
( M5-35)........................2
The wall-hanging bracket weights approx. 6 kg (13.2 lbs.), a 50-inch display weights approx. 45 kg (99.2 lbs.), a 42-inch display weights approx. 30 kg (66 lbs.). Using the bracket dimensions shown in the diagram at right, confirm that the 6 locations for mounting the bracket to the wall are able to bear the combined weight. If the wall is not strong enough, reinforce it.
4
Installation procedure
The wall-hanging bracket has 24 installation holes. If the wall material is not strong enough to install the display using six installation holes, use some of the spare holes. However, depending on the wall material, cracks may develop and attachment intensity becomes inadequate if the screws are inserted too close to each other.
Note
Note
1. Check the strength of the installation location.
2. Install the wall-hanging bracket to the wall.
Hang the bracket so that the arrow on the bracket points to the right.
If it is necessary to embed bolts or nuts beforehand because the wall is made of concrete, use
the bracket itself to determine the correct installation hole positions, or use the dimension diagram to calculate the hole positions. Then embed the M6 bolts or nuts into the holes. Embed the bolts so that they protrude from the wall by 10 mm (
13
/32 inch) to 15 mm (19/32 inch).
Units
: mm
( ): inch
930 (36
5
/8)
490 (19 19/64) 450 (17
23
/32)
50
(1
31
/32)
30
(1
3
/16)
20
(
25
/32)
20
(25/32)
450 (17
23
/32)450 (17
23
/32)
100
(3
15
/16)50
(1
31
/32)
15
(
19
/32)
Wall installation holes
(6 locations)
Used for routing wires
behind a wall
15
(19/32)
Dimensions of the wall-hanging bracket (sold separately)
Fixing screw
Fixing screw
Installation procedure
1.
Insert a bolt into the upper right hole.
2.
Use a level to adjust the bracket so that it is parallel to the ground. Insert bolts into the other 5 holes.
3.
Insert and slightly tighten the fixing screw (M5 x 35). Do not insert the bolt more than 5 mm (
13
/64inch). The display cannot be installed in the correct position if the bolt is over­tightened.
*
Note: In this case, the wall-hanging bracket fixing screw
(M5 x 135) is not used.
Use commercially available bolts which suit the wall materials for installation to the wall.
Note
Note
Loading...
+ 8 hidden pages