Panasonic PV-DM2792 User Manual

TV / DVD / VCR Combination

Operating Instructions

Model No. PV-DM2792

Initial Setup

Basic Operation

TV Operation

Timer Operation

• Initial Setup and Connection Procedures are on pages 14 to 17.

As an ENERGY STAR
determined that this product or product model meets the
guidelines for energy efficiency.

Please read these instructions carefully before attempting to connect,
operate, or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

®

Partner, Matsushita Electric Corporation of America has

E

NERGY STAR

®

LSQT0520A

Advanced Operation

For Your Information

Important Safeguards and Precautions

READ AND RETAIN ALL SAFETY AND
OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON UNIT

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from power source indicated on unit
or in this manual. If uncertain, have your Electric
Utility Service Company or Video Products Dealer
verify your home power source.

2 POWER CORD PLUG

For safety, this unit has a polarized type plug (one
wide blade), or a three-wire grounding type plug.
Always hold the plug firmly and make sure your
hands are dry when plugging in or unplugging the
AC power cord. Regularly remove dust, dirt, etc.
on the plug.

POLARIZED PLUG CAUTION:

The plug fits into outlet one way. If it cannot be fully
inserted, try reversing it. If it still will not fit, have an
electrician install the proper wall outlet. Do not
tamper with the plug.

GROUNDING PLUG CAUTION:

The plug requires a three-hole grounding outlet.
If necessary, have an electrician install the proper
outlet. Do not tamper with the plug.

3 POWER CORD

To avoid unit malfunction, and to protect against
electrical shock, fire or personal injury:

- Keep power cord away from heating appliances
and walking traffic. Do not rest heavy objects on,
or roll such objects over the power cord.

- Do not tamper with the cord in any way.

- An extension cord should have the same type
plug (polarized or grounding) and must be
securely connected.

- Overloaded wall outlets or extension cords is a
fire hazard.

- Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and should
be replaced by a qualified electrician.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat
generated during operation. If blocked, heat
build-up may result in a fire hazard or heat
damage to cassettes or discs.
For your protection:
a. Never cover ventilation slots while unit is ON,

or operate unit while placed on a bed, sofa,
rug, or other soft surface.

b. Avoid built-in installation, such as a book case

or rack, unless properly ventilated.

5

AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES

Do not place unit over or near a heater or radiator,
in direct sunlight, inside closed vehicles,
in high temperature [over 95˚ F (35˚ C)], or in over
75% humidity. If unit is suddenly moved from a
cold place to a warm one, moisture may
condense in unit and on the tape causing
damage. Never subject unit to vibration, impact,
or place it so that the surface is tilted as internal
parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Never place unit on support or stand that is not
firm, level, and adequately strong.
The unit could fall causing serious
injury to a child or adult and
damage to the unit.

• Move any appliance and cart
combination with care.
Quick stops, excessive force, and
uneven surfaces may cause objects to overturn.

2

• Carefully follow all operating instructions.

OUTDOOR ANTENNA INSTALLATION

1 SAFE ANTENNA AND CABLE CONNECTION

An outside antenna or cable system must be properly
grounded to provide some protection
against built up static charges
and voltage. Section 810
of the National Electrical
Code, ANSI/NFPA 70 (in
Canada, part 1 of the
Canadian Electrical Code)
provides information
regarding proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE

POWER LINES OR CIRCUITS

Locate an outside antenna system well away from power
lines and electric light or power circuits so it will never
touch these power sources should it ever fall. When
installing antenna, absolutely never touch power lines,
circuits or other power sources as this could be fatal.

ELECTRIC
SERVICE
EQUIPMENT

NEC

- NATIONAL ELECTRICAL CODE

GROUND
CLAMP

ANTENNA
LEAD IN
WIRE

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)

USING THE UNIT

Before unit is brought out of storage or moved to a new location,
refer again to the INSTALLATION section of these safeguards.

1 KEEP UNIT WELL AWAY FROM WATER OR

MOISTURE, such as vases, sinks, tubs, etc.

2 IF EXPOSED TO RAIN, MOISTURE, OR

STRONG IMPACT,

by a qualified service technician before use.

3 ELECTRICAL STORMS

During a lightning storm, or before leaving unit unused for
extended periods of time, disconnect all equipment from
the power source as well as the antenna and cable system.

4 WHEN UNIT IS PLUGGED IN

• DO NOT OPERATE IF:

- liquid has spilled into unit.

- unit was dropped or otherwise damaged.

- unit emits smoke, malodors, or noises.
Immediately unplug unit, and have it inspected by a
service technician to avoid potential fire and shock hazards.

•

Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or fire hazard.
Do not put any foreign object on the tray.

• Keep magnetic objects, such as speakers, away from
unit to avoid electrical interference.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer
to avoid risk of fire, shock, or other hazards.

6 CLEANING UNIT

Unplug unit. Use a clean, dry, chemically untreated cloth to
gently remove dust or debris. DO NOT USE cleaning fluids,
aerosols, or forced air that could over-spray, or seep into unit and
cause electrical shock. Any substance, such as wax, adhesive
tape, etc. may mar the cabinet surface. Exposure to greasy,
humid, or dusty areas may adversely affect internal parts.

unplug unit and have it inspected

SERVICE

1 DO NOT SERVICE PRODUCT YOURSELF

If, after carefully following detailed operating instructions, the
unit does not operate properly, do not attempt to open or
remove covers, or make any adjustments not described in the
manual. Unplug unit and contact a qualified service technician.

2 REPLACEMENT OF PARTS

Make sure the service technician uses only parts specified
by the manufacturer, or have equal safety characteristics
as original parts. The use of unauthorized substitutes may
result in fire, electric shock, or other hazards.

3 SAFETY CHECK AFTER SERVICING

After unit is serviced or repaired, request that a thorough safety
check be done as described in the manufacturer’s service
literature to insure video unit is in safe operating condition.

Safety Precautions/Mesures de sécurité

Warning : To prevent fire or shock hazard, do not expose this equipment to rain or moisture.

Caution : To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement : Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas

Attention : Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la

FCC WARNING :Any unauthorized changes or modifications to this equipment

would void the user’s authority to operate.

exposer cet appareil à la pluie ou à une humidité excessive.

borne correspondante de la prise et pousser jusqu’au fond.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT
PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY
AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE
UNIT YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION:

LASER RADIATION
WHEN OPEN. DO NOT
STARE INTO BEAM.

ATTENTION:

RAYONNEMENT LASER
EN CAS D’OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.

(Inside of product)

FCC NOTICE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when operated in a residential
environment. If this eqiupment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, use the equipment in another location and/or utilize an
electrical outlet different from that used by the receiver. If necessary, consult the dealer or an
experienced radio/TV technician for help. You may find the booklet, 'Something About Interference'
available from FCC local regional offices helpful.

This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead.
Disposal of these materials may be regulated in your community due to environmental
considerations. For disposal or recycling information please contact your local authorities, or the
Electronics Industries Alliance: <http://

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS

INSIDE REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL

www.eiae.org.>

This symbol warns the user that uninsulated voltage within the unit may
have sufficient magnitude to cause electric shock. Therefore, it is
dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the
operation and maintenance of this unit has been included. Therefore, it
should be read carefully in order to avoid any problems.

Region Management Information

Region Management Information: This unit is designed and
manufactured to respond to the Region Management
Information that is recorded on a DVD disc. If the Region
number described on the DVD disc does not correspond to
the Region number of this unit, this unit cannot play this disc.

The Region number
for this unit is 1.

1

3

Before Using

Congratulations

on your purchase of one of the most
sophisticated and reliable products on the
market today. Used properly, it will bring you
and your family years of enjoyment. Please fill in
the information below. The serial number is on
the tag located on the back of your unit.

Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.

PV-DM2792

Accessories

Remote Control
LSSQ0302

Batteries
2 “AA”

Loading the Batteries

1) Open the cover.

2) Insert batteries as
marked.

3) Close the cover.

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

Prevent Accidental Tape Erasure

Break off the tab
to protect.

Record Tab

To order accessories,
call toll free 1-800-332-5368.

SELF-DEMO Mode

4

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Screw driver

To record again.

Cover the hole
with cellophane tape.

Record/Playback Time

Only use tapes with the mark in this unit.

Tape Speed

Setting

SP (Standard Play)

LP (Long Play)

SLP

(Super Long Play)

Type of Video Cassette

T120T60

1 Hour

2 Hours 4 Hours

3 Hours 6 Hours 8 Hours

2 Hours

T160

2 Hours

40 Minutes

5 Hours

20 Minutes

Table of Contents

Initial Setup

TV / VCR

Important Safeguards and Precautions / Safety Precautions ........ 2 - 3

Before Using ........................................................................................ 4

Information (Unit, Cassette, Disc) .................................................. 6 - 7

Location of Controls ...................................................................... 8 - 10

Connections ................................................................................ 11 - 13

Initial Setup .................................................................................. 14, 15

Reset Language, Channels, Clock, Time Zone Adjust ............... 16, 17

Basic Operation

TV / VCR

DVD

Playback a Tape ................................................................................ 18

Record On a Tape ............................................................................. 18

Copy Your Tapes (Dubbing) .............................................................. 19

Basic DVD Operation .................................................................. 20, 21

TV Operation

TV / VCR

TV Operation ..................................................................................... 22

MTS Broadcast / TV Stereo System ................................................. 23

Closed Caption System ............................................................... 24, 25

TV Timer Features ............................................................................. 26

On-Screen Display (OSD) ................................................................. 27

FM Radio...................................................................................... 28, 29

Timer Operation

TV / VCR

Timer Recording........................................................................... 30, 31

Initial Setup

Basic Operation

TV Operation

Timer Operation

Advanced Operation

TV / VCR

DVD

Cable Box Universal Remote Control Feature ............................ 32, 33

Tape Operation ........................................................................... 34 - 37

Special VCR Features ................................................................ 38, 39

V-Chip Control Feature .............................................................. 40 - 43

Audio Features ............................................................................ 44, 45

Video / Audio Menu ........................................................................... 46

Video / Audio Adjustment .................................................................. 47

Disc Operation ............................................................................ 48 - 51

MP3 Playback Operation .................................................................. 52

DVD Operation using On-Screen Displays ................................ 53 - 55

DVD Lock Feature ............................................................................. 56

For Your Information

TV / VCR

DVD

Before Requesting Service.......................................................... 60, 61

Warning and Instruction Displays ...................................................... 62

Spanish Quick Use Guide / Guía para rápida consulta ............. 65 - 71

Index ............................................................................................ 72, 73

Limited Warranty ............................................................................... 74

Customer Services Directory ............................................................ 75

Settings for DVD Operation ........................................................ 57 - 59

Language Code List .......................................................................... 63

Advanced Operation

.

For Your Information

5

Information (Unit, Cassette, Disc)

SpecificationsHead Cleaning

Playing older or damaged tapes may eventually
cause video heads to become clogged.

Head Clog Sensor

During playback this
screen appears if clogging
is detected. To remove
screen, press PLAY on the
remote or unit.

• Use “dry” type head cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape directions carefully.
Excessive use of head cleaning tape can shorten
the video head life.

• If head clog symptoms persist, contact your
nearest Factory Service Center or authorized
Service Center. (See Page 64.)

V I DE

O

HEADS MAY

NEED C

LEAN I NG

PL

EASE

I

NSERT HEAD

C

LEAN I NG CASSETTE

REFER TO MANUAL

OR

END : PLAY

DST (Daylight Saving Time)

Unit auto adjusts clock for DST (Daylight Saving Time.)

■ Spring (First Sunday in April)

DST : ON ➔ Sets clock ahead one hour.

■ Autumn (Last Sunday in October)

DST : ON ➔ Turns clock back one hour.

• If your area does not observe Daylight Saving
Time, select DST : OFF (see “Clock” on pages 16
and 17).

• Keep these time changes in mind when
programming the unit for timer recordings.

Features for a Quality Picture

Digital Auto Tracking

Continuously analyzes the signal and adjusts for optimum
picture quality.

Manual Tracking Control (to reduce picture noise)

Use during Playback and Slow Motion mode to reduce
picture noise. Press the 3 or 6 number key on the remote
control or CH

on the unit until the picture clears up.
To return to Auto Tracking, press POWER off, then on
again a few seconds later.

V-Lock Control

In Still mode, the 3 or 6 number key on the remote control or
CH

on the unit operate as a V-Lock control to reduce jitter.

PanaBlack

This unit uses a PanaBlack

TM

Picture Tube

TM

picture tube for better color

reproduction and picture contrast.

6

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Display

Picture Tube: 27 inch measured

diagonal 100˚ deflection
Picture Tube

VCR

Video Recording System:

Audio Track: 1 track (Normal)

4 rotary heads helical
scanning system

2 channel
(Hi-Fi Audio Sound)

Tun er

Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels: Midband A through I (14 ~ 22)

Superband J through W (23 ~ 36)

Hyperband AA ~ EEE (37 ~ 64)
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01)
Ultraband 65 ~ 94, 100 ~ 125

FM Radio

Band range: 87.5 ~ 108.1 MHz

General

Power Source: 120V AC, 60 Hz
Power Consumption:

Power On
Approx. 170 watts
Power Off

Approx. 3.5 watts
Television System: EIA Standard NTSC color
Speaker: 2 pieces
Operating Temperature:

5˚ C ~ 35˚ C (41˚ F ~ 95˚ F)
Operating Humidity: 10 % ~ 75%
Weight:
Dimensions:

42 kg (92.4 lbs.)

772 (W) x 654 (H) x 533 (D) mm

30-

3/8” (W) x 25-3/4” (H)

x 21” (D)

Discs played

(1) DVD-VIDEO disc

5” (12 cm) single-sided,

single-layer

5” (12 cm) single-sided,

double-layer

5” (12 cm) double-sided,

double-layer

(one layer per side)

3” (8 cm) single-sided,

single-layer

3” (8 cm) single-sided,

double-layer

3” (8 cm) double-sided,

double-layer

(one layer per side)
(2) Compact disc 5” (12 cm) disc
(CD-DA, CD-RW,

3” (8 cm) disc
VIDEO CD)

Digital audio output:

Optical digital output: Optical connector
Pickup: Wave length:

655 nm (DVD)
790 nm (Video CD/CD)

Laser power: CLASS II

Note : Designs and specifications are subject to change

without notice.

Disc formats supported by this unit

The unit can play back discs bearing any of
the following marks:

DVD

3” (8 cm) disc / 5” (12 cm) disc

Video CD

3” (8 cm) disc / 5” (12 cm) disc

CD

3” (8 cm) disc / 5” (12 cm) disc

Discs which cannot be played with this unit

• DVD with Region No. other than “1” or “ALL”

• DVD of PAL system

• DVD-ROM

• DVD-R/DVD-RAM

• CD-ROM

• CDV

• CD-G

• Do not try to play a Photo CD.

is a registered trademark.

Definition of Terms

Angle

Some DVD discs feature scenes simultaneously
shot from different angles. The ANGLE button can be
used to view the scene from different angles.
(ANGLE Indicator lights up on the unit when a scene
recorded at different angles is detected.)

Chapter Number

Titles are subdivided into numbered sections. You can
quickly search for a favorite scene using these numbers.

DVD

A high-density optical disc on which high-quality
pictures and sound have been digitally recorded.
DVD incorporates new video compression technology
(MPEG II) and high-density recording technology
which allow entire movies to be recorded with
incredible playback quality.

Playback Control

With Video CD (version 2.0), scenes or information
may be selected for viewing or listening from an
interactive menu that appears on the TV screen.

Subtitles

Written dialogue which appears at the bottom of the screen.

Time Number

The elapsed play time from the start of a disc or title.
Use to quickly find scenes.

Title Number

For DVD discs with two or more titles, the title is
numbered as title 1, title 2, etc.

Track Number

Numbers assigned to tracks on Video CDs and CDs
to allow specific tracks to be quickly located.

Video CD

CD containing picture and sound with same quality
level as video tape. This unit also supports Video
CDs with playback control (version 2.0).

(May not work with some discs.)

Disc Handling

Handling precautions

• Only hold disc by edges as shown.
Fingerprints, dirt, and scratches
can cause skipping and distortion.

• Do not write on label
side of disc.

• Never use record
cleaning sprays, benzine,
thinner, static electricity
prevention liquids, or any
other solvent.

• Be careful not to drop or
bend disc.

• Do not place more than
1 disc on disc tray.

• Do not try to close disc
tray when disc is not
properly placed.

• Always store discs in their
proper cases when
not in use.

To clean disc surface

With a soft, damp (water only) cloth, gently wipe from
the center hole to the outer edge as shown below.
(Wiping in a circular pattern will scratch the surface.)

If disc is brought from a cold to a warm
environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth
before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216,
and 4,819,098, licensed for limited viewing uses only.

This product incorporates copyright protection technology
that is protected by method claims of certain U.S. Patents
and other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or
disassembly is prohibited.

Disc tray

Disc

Initial Setup

7

Location of Controls

Remote Control Buttons

EJECT/OPEN/CLOSE

See next page.

POWER

Turn the unit on or off.

TV/VCR

Sets to TV/VCR mode.

MUTE

Mutes the sound instantly.

CHANNEL UP/DOWN

Selects a channel.

SURROUND

Hears a deeper, 3-D sound effect.

NUMBER Keys

Selects a channel directly.

ANGLE

Selects the desired angle
in DVD mode.

AUD IO

Selects the desired audio mode.

TITLE

Selects the desired title by number
on some DVDs.

SELECT

Control navigation around
on-screen menu.

ACTION

Displays Main Menu.

SET

Sets a selected menu.

REW/SLOW-

Rewinds tape and searches reverse
scene. Decreases slow motion
speed in Still mode.

STILL/PAU SE

Pauses picture in Play mode and
frame advance picture in Still mode.

SKIP /SEARCH

Skips back one chapter or track. Goes to
previous menu screen. Goes directly
to the desired recording. Locates end
point of recording.

PLAY

Begins

playback.

SKIP

Skips one chapter or track. Goes to next

screen. In Stop mode, goes to the counter
“0:00:00”. In Play mode, skips
3 minutes of tape.

8

/CM SKIP/ZERO SEARCH

over 1 to

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

DVD

Sets to DVD mode.

LIGHT

See next page.

DSS/CABLE

Sets the remote to control some
basic DDS or Cable box functions.

FM

Receives FM radio signal.

VOLUME UP/DOWN

Adjusts volume.

RAPID TUNE

Displays the last channel
you were watching.

ADD/DELETE/CLEAR

Adds or deletes a channel.
Cancels an item on the screen.

SUB TITLE

Selects a different subtitle language.

DISPLAY/ENTER

Displays the TV status and clock.
In DVD mode, displays disc and
unit information.
In DSS or CABLE mode, it may be
necessary after channel selection.

MENU

Displays DVD menu.

PROGRAM

Displays SET PROGRAM screen.
You can set Timer Program and
On-Timer.

FF/SLOW+

Fast forwards tape and searches
forward scene. Increases slow
motion speed in Still mode.

ZOOM/COUNTER RESET

Enlarges specific portions of DVD
picture. Resets to “0:00:00” at
desired portion of tape.

REC

Records a program.

RETURN/SPEED

Returns to DVD menu screen.
Selects recording speed of tape.

STOP

Stops playback.

Location of Controls (continued)

Universal Light Tower® Illuminated Remote Control

LIGHT button:

When LIGHT is pressed, (DVD,
buttons will light for 5 seconds for easy button location.
If no button is pressed in 5 seconds, the light goes out to conserve the battery.

EJECT/OPEN/CLOSE button:

When this button is pressed in TV-VCR mode, the tape is ejected.
This button is inoperative if pressed during recording.
If pressed in DVD mode, the disc tray opens or closes.

, DSS/CABLE, CH UP/DOWN, VOL UP/DOWN)

Indicators on the Front Panel

Initial Setup

ANGLE Indicator

Lights up when a scene
recorded at different
angles is detected.
(DVD only).

Pg. 49

PROG TIMER Indicator

Lights up when the unit is set for

Recording. It flashes when

Timer
a Timer Recording has been set
with no tape inserted, the clock is
not set, or the tape is in motion.
Pg. 30
Lights up when the On Timer is set.
Pg. 26

Remote Sensor

REC Indicator

Lights up during recording.
In Rec Pause or OTR
Pause mode, the Indicator
flashes.
Pg. 18

9

Front View of the unit

If the disc cannot be removed...

First, unplug unit.
Then, prepare a rigid wire (e.g. an
extended paper clip) and, applying
moderate force, insert it straight into the
hole at the base of the tray. The tray will
eject a little. Now, pull the tray all the
way out and remove the disc.

PHONES

Connect an earphone
or headphones.

AUDIO/VIDEO IN
Connector

Connect from other
component.

POWER (See page 8.)

STOP (See page 8.)

PLAY (See page 8.)

OPEN/CLOSE (See page 8.)

REWIND/SEARCH (See page 8.)

SKIP (See page 8.)

SKIP (See page 8.)

DVD

Disc Tray

Cassette
Compartment

Built-In SpeakerX2

CHANNEL UP/DOWN

(See page 8.)

TRACKING UP/DOWN

(See page 8.)

VOLUME UP/DOWN

(See page 8.)

REC

(See page 8.)

PLAY/REPEAT

(See page 8.)

STOP/EJECT

(See page 8.)

FAST FORWARD/
SEARCH

(See page 8.)

10

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Location of Controls (continued)

Rear View of the unit

VHF/UHF Antenna
Input Terminal

See below.

AC Power Plug

When plugged into an AC outlet,
this unit consume W of

s 3.5

electric power in OFF condition.

Connections

Initial Setup

Audio Output

Connector (L/R)

Pg. 12

Optical digital audio

output connector

Pg. 13

For ANT./Cable
Connect the cable from
Antenna/Cable to the VHF/UHF
terminal on the unit.

For DSS/Cable Box
Connect the OUT jack on your
cable box to the VHF/UHF
terminal on the unit with a RF
cable.

WARNING:

Overtightening “Nut type” RF coaxial cables
may damage jacks. Finger tighten only.

UNIT

IN from
ANT./CABLE

V

H

F

/

U

HF

VHF/UHF

Cable TV
Converter Box

V

H

F

/

U

HF

IN from
ANT./CABLE

11

Connections (continued)

Audio connections

■

Unit ➔ Amplifier ➔ Speaker

Unit

AUDIO OUT
R L

Amplifier

R L

AUDIO IN

Speaker

Speaker

Ready Checklist

Turn down the volume, then turn this unit, as well as
other equipment to be connected, off before
proceeding with connection.
Do not block ventilation holes of any of the
equipment and arrange them so that air can
circulate freely.
Read through the instructions before connecting
other equipment.
Ensure that you observe the color coding when
connecting audio and video cables.

Enjoying digital audio output from the
digital audio output connector

Notes on audio output from the optical digital
audio output connector

Disc

Sound
recording
format

Dolby Digital

DVD

Linear PCM
(48/96 kHz
16/20/24 bit)
dts

Video
CD

CD

*1 The type of audio output from the connector can be

*2 Sound having 96 kHz sampling is converted into 48

MPEG 1

Linear PCM

selected by the Settings for DVD Operation. (See
page 60.)

kHz sampling when it is output from the unit’s optical
digital audio output connector.

Optical digital audio
output from connector

Dolby Digital bitstream
(1-5.1 ch) or OFF (no
output)*

1

Linear PCM (2ch)
(48 kHz sampling/16 bit
only)*

2

or no output*

1

Bitstream or no output*
PCM
(44.1 kHz sampling)
Linear PCM
(44.1 kHz sampling)

1

Manufactured under license from Dolby
Laboratories. “Dolby”, and the double-D
symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. © 1992-1997
Dolby Laboratories, Inc. All rights reserved.

12

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

For your reference:

• Dolby Digital is a digital sound compression technique
developed by the Dolby Laboratories Licensing
Corporation. Supporting 5.1-channel surround sound,
as well as stereo (2-channel) sound, this technique
enables a large quantity of sound data to be efficiently
recorded on a disc.

• Linear PCM is a signal recording format used in CDs.
While CDs are recorded in 44.1 kHz/16 bit, DVDs are
recorded in 48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you
will obtain the full benefit of Pro Logic from the same
DVD movies that provide full 5.1 channel Dolby Digital
soundtracks, as well as from titles with the Dolby
Surround mark. For information on Panasonic or
Technics Dolby Pro Logic Surround Sound Decoders
please contact your local dealer.

Unit Decoder with Dolby Digital Amplifier ➔➔➔ Speaker

■

or

dts (digital theater systems)

When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or dts bitstream
is output from the unit Optical digital audio output connector. When the unit is connected to a
Dolby Digital decoder or dts decoder, you can enjoy theater-quality audio in your home.
[An optical digital audio cable (optional) is required when an optional Dolby Digital decoder or
dts decoder is used.]

Initial Setup

Notes on connecting an Optical
digital audio cable (optional)

•

Firmly connect the cable to

the connector.

Caution for optical digital audio
output connector:

• When connecting an amplifier (with
an Optical digital input connector)
which does not contain the Dolby
Digital or dts decoder, be sure to
select “OFF” at “Dolby Digital” and
“OFF” at “dts” of the Settings for
DVD Operation “AUDIO OUTPUT”
(see page 58). Otherwise, any
attempt to play DVDs may cause
such a high level of noise that it may
be harmful to your ears and damage
your speakers.

• When a dts decoder is connected,
please select “Bitstream” at “dts” of
the Settings for DVD Operation
“AUDIO OUTPUT”. If “OFF” is
selected, there will be no sound.
(See page 58).

• Video CDs and CDs can be played
as normal.

Note:

• Some dts decoders which do not
support DVD-dts interface may not
work properly with the unit.

Unit

Optical digital audio
cable (optional)

Amplifier

Front
Speaker

Subwoofer

Surround
speaker

Decorder with Dolby Digital/
dts processing (optional)

Center speaker

Front

Speaker

Surround

speaker

13

Initial Setup (Ready to Play)

COMPLETED

2 / 6/

2002

WED

PM

Please make all cable or antenna connections before powering on.

Initial Setup (Ready to Play)

Press

on the remote for TV-VCR mode.

Plug the unit power cord into an AC wall outlet.

1

Press Power* on the remote or unit. The unit
comes on and auto channel and clock set starts.

2

CH AUTO SET PROCEEDING

• If you use a cable box, turn it on and set it to the Public
Broadcasting Service (PBS) channel in your time zone.
If you use a DSS receiver, it must be turned off.

AUTO CLOCK SET

PROCEEDING

CANCEL : PRESS STOP KEY

Settings are made automatically.
When setup is done, this screen appears.

3

POWER
TV-VCR

SELECT

SET

ACTION

14

2 / 6 /

2002

WED 12 : 00PM

DST : O

ETED

N

0

SETT I NG : CH 1

UTO CLOCK SET

A

MPL

CO

If AUTO CLOCK SET IS INCOMPLETE
screen appears, set the clock using MANUAL
CLOCK SET procedure on next page.

SET

CLOC

K

2 / 6/

2002

SESET COMPLETED

SET : SET BACK:

START

:

ACT I ON

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

WED

12

DST : O

:

00

PM

N

on the remote and try the button again.

1 / /

COMPLETED

PM

s the button

Press ACTION on the Remote to
display SET CLOCK Menu screen.

CLOC

K

1 / /

SESELE CT MONTH

SELECT :
SET :
END

Press

to select the month

and press

SET

SET

:

ACT I ON

SET to set. In the same

DST

:

: ON

manner, select and set the date,
year, time, and DST. (Daylight
Saving Time)

CLOC

K

SET

2 / 6/

2002

SESET COMPLETED

SET

SET :
START

:

ACT I ON

WED

12

DST : O

BACK:

:

00

PM

N

Press ACTION twice to start
CLOCK and exit.

Reset all unit Memory Functions

When moving unit to a new location, or if a
mistake was made in the Initial Setup section.

• Make sure a tape is not inserted in the unit.

SKIP

Turn the unit

1

Power on.

Press and hold both PLAY and

2

FF on the unit for more than 5

seconds.

• The power will shut off.

• Please ignore “NO CASSETTE” warning.

Do “Initial Setup” on page 14.

3

Initial Setup

Note to CABLE System Installer

This reminder is provided to call the
CABLE (Cable TV) System Installers
attention to Article 820-40 of the NEC
that provides guidelines for proper
grounding and, in particular, specifies
that the cable ground shall be
connected to the grounding system of
the building, as close to the point of
cable entry as practical.

Reset Language, Channels, Clock,

M A I N MENU

1

DVD

TV

SELECT :
END : ACT I ON

Language Channels

2

1) Press to
select language
icon.

DVD

TV

SELECT :
END : ACT I ON

2) Press SET
repeatedly.

MENU PR I NCIPAL

DVD

ELEG I R :
TERM I NAR :

For Spanish

DVD

SEL. :

REGLER : SET

FIN :

ACT I ON

For French

DVD

TV

SELECT :
END : ACT I ON

For English

3) Press ACTION to
exit.

LOCK

CLOC

K

M A I N MENU

LOCK

CLOC

BLOQUEO

RELOJTV

F I

ACT I ON

MENU

BLOCAGE

HORLOGETELE

M A I N MENU

LOCK

CLOC

LANGUAGE

1

3

5

CH

SET : SET

LANGUAGE

5

CH

K

SET : SET

HOLA

ID I OMA

5

CANAL

JAR : SET

BONJOUR

LANGUE

3

5

CANAL

HELLO

LANGUAGE

5

CH

K

SET : SET

Press ACTION*

to display MAIN MENU.

1) Press
select “CH.”

DVD

1

3

1

3

1

1

3

TV

SELECT :
END : ACT I ON

2) Press SET.

SET UP CHA

ANT

ENNA

A

UTO SE
CHANNEL CAPT I ON
W

EAK S I GNAL

SELECT :

SET

: SET

END

: ACT I ON

3) Press to select
“ANTENNA,” then
press SET to set
your antenna system
(“TV” or “CABLE”).

4) Press
“AUTO SET,” then
press SET.

• After Channel Auto
Set is finished, Clock
Auto Set will be
performed.

(If clock is set manually,

Clock Auto Set will not
be performed.)

M A I N MENU

LOCK

CLOC

: CABLE

T

D I

to

LANGUAGE

3

5

CH

K

SET : SET

NNE

L

SPLAY : OFF

to select

Clock

1) Press
select “CLOCK.”

M A I N MENU

1

DVD

TV

SELECT :
END : ACT I ON

2) Press SET.

SET CLOCK

AUTO CLOCK SET

MANU

AL

T I M

E ZONE AD

SELECT :
SET

: SET

: ACT I ON

END

(“TIME ZONE ADJUST”

appears only when
auto clock is set.)

3)Press to select
“MANUAL,” then
press SET.

(For Auto Clock Set,
select “AUTO CLOCK
SET,” and press SET.)

SET

2 / 6/

2002

SELE CT

HOUR

SELECT :
SET :

SET

START

:

ACT I ON

<Example MANUAL
CLOCK SET screen>

Continued on the
next page.

to

LANGUAGE

LOCK

3

5

CH

CLOC

K

SET : SET

JUS

T :

CLOC

K

:

WED

12

00

: ON

DST

BACK :

1

0

PM

16

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Time Zone Adjust

Time Zone Adjust

4)Press and
press SET to select

and set the month,
date, year, time, and
DST

(Daylight Saving

Time)

.

To Make Corrections,

repeatedly press
to move to error, then
correct.

5) Press ACTION
twice to

start the
clock and exit this
mode.

(Only when Auto Clock is set.)

1) Press to
select “CLOCK.”

DVD

TV

SELECT :
END : ACT I ON

2) Press SET.

AUTO CLOCK SET
MANU

T I M

SELECT :
SET

:
: ACT I ON

END

M A I N MENU

LOCK

CLOC

SET CLOCK

AL

E ZONE AD

K

LANGUAGE

5

CH

SET : SET

JUS

T :

1

3

0

Important:

*

If a remote control button does not work
when pressed, press the button on
the remote and try the button again.

NUMBER
keys

ADD/DLT

SELECT

SET

ACTION

Initial Setup

3)Press

to select
“TIME ZONE
ADJUST” and

press

or to
subtract or add
hour(s) as
necessary.

SET CLOCK

AUTO CLOCK SET
MANU

AL

T I M

E ZONE AD

SELECT :
SET

:

END

: ACT I ON

JUS

T :

4)Press ACTION
twice to exit.

Add or Delete a Channel

To add channel:
Select channel with number
keys and press ADD/DLT.

C

HANNEL

08 ADDED

+1

To delete channel:
Select channel with CH
or number keys and press
ADD/DLT.

C

HANNEL

08 DELE T

ED

17

Playback a Tape

Record On a Tape

Ready Checklist

All connections are made.
Your unit is plugged in.

Insert a tape.

1

Record
tab

To prevent tape jam,

remove loose or peeling
labels from tapes.

Press PLAY* to play a tape.

• If tape has no record tab (see page 4),

2

auto play begins.

Forward/Reverse scene search

■

➔ Press FF/SLOW+ or REW/SLOW-.
➔ Press again or PLAY to release.

Still (Freeze) picture

■

➔ Press STILL/PAUSE.
➔ Press PLAY to release.

Slow Motion picture

■

➔ Press FF/SLOW+ (increases speed) or

REW/SLOW- (decreases speed) in

Still mode.

➔ Press PLAY to release.
Frame by Frame picture

■

➔ Press STILL/PAUSE in Still mode.
➔ Press PLAY to release.

Notes

• These features work best in SP or SLP mode.

• After the unit is in Still or Slow mode for 3
minutes, it will switch to Stop mode automatically
to protect the tape and the video head.

Stop ➔ Press STOP

■

Rewind tape ➔ Press REW/SLOW-

■

■

Fast forward tape ➔ Press FF/SLOW+

Eject tape ➔ Press EJECT on the remote

■

Operation using unit buttons

Insert a tape.

REC Indicator

18

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

• The unit power comes
on automatically.

in Stop mode

in Stop mode

or STOP/EJECT on the unit

PLAY/
REPEAT

CH

REC

Press to stop
and/or eject tape.

Insert a tape with record tab.

• The unit power comes on automatically.

1

Press CH or number keys to
Select Channel.

2

• For “LINE” input, see bottom of next page.

Press SPEED to select recording

(see page 4).

speed

3

SP = Standard Play
LP = Long Play
SLP = Super Long Play

• Selected speed is displayed.

Press REC to start recording.

• To edit out unwanted portions, press

4

■

■

REW/SLOW-

STILL/PAUSE to pause and resume
recording.

• You cannot view another channel during
recording.

Stop Press STOP

➔

One Touch Recording (OTR)
Press REC repeatedly

to set the recording
length (30 min - 4 hours.)

• The unit stops recording at a preset time.

• PROG TIMER Indicator lights on the unit.

Notes

• It is not possible to record from DVD/
Video CD/CD to VHS tape using this unit.

• After the unit has been in Rec Pause mode for

5 minutes, it will stop automatically to protect
the tape and the video head.

• The remaining recording time of an OTR can be

displayed by pressing DISPLAY.

SELECT

SET

ACTION

STILL/

PAUSE

Normal Rec

0:30 1:00

EJECT

CH

CH

NUMBER
keys

DISPLAY

PLAY

FF/SLOW+

STOP

REC

SPEED

1:302:003:004:00

Important:

*

Copy Your Tapes (Dubbing)

If a remote control button does not work
when pressed, press the
the remote and try the button again.

button on

Connections you’ll need to make

Playing (Source) VCR

R-AUDIO-L

OUT

IN

VIDEO

MONO

Playback (Source)

Insert pre-

1

recorded tape.

2

Press PLAY then

3

PAUSE at starting
point t

o put in

Standby mode.

Recording (Editing) unit

IN FROM

ANT.

OUT TO

TV

L-AUDIO IN-RVIDEO IN

Recording (Editing) unit

Insert blank tape
with record tab.

• Dubbing tapes protected
with Copy Guard will have
poor quality results.

Select “LINE” mode.

See “Selecting Input Mode” below.

Press REC, then
Press STILL/PAUSE

immediately

Standby mode.

to put in

Basic Operation

(Perform operation of steps 4 and 5 on both units at same time.)

Press PLAY

4

5

Caution

• Unauthorized exchanging and/or

copying of copyrighted recordings
may be copyright infringement.

• Please note that some tapes
cannot be dubbed on this unit.
Also, it is not possible to dub
DVD/Video CD/CD to VHS tape
using this unit.

STOP

to start dubbing.

Press STOP

to stop dubbing.

Selecting Input Mode

Method 1:
Press CH

Method 2:
a Press ACTION for MAIN MENU.
b Press

for SET UP TV screen.

c Press

then press SET to select “TUNER” or “LINE”

d Press ACTION twice to exit this mode.

to select “INPUT SELECT,” and

Press STILL/PAUSE

to start dubbing.

Press STOP

to stop dubbing.

. The display will change as follows.

to select “TV”, then press SET

1

2

(CABLE)

3

(TV)

or

125LINE

69

19

Basic DVD Operation

Ready Checklist

All connections are made. (See page 11.)
Your unit is plugged in.
If unit is connected to an audio amplifier,

turn the stereo system’s power on.

Operation using unit buttons

Press PLAY.

4

Insert disc.

3

•

7

3

Press
OPEN/CLOSE.

Press POWER* on the remote or unit.

1

Press DVD to select DVD mode.

• If a disc is already inserted, go to step 4.

2

(Depending on the disc, playback may start
automatically.)

Insert a disc.

1) Press OPEN/CLOSE.

3

2) Place disc into disc tray.

• Hold disc by its edges only
(page 7

) with printed side up

use guides to place into

and

1

tray. Use

2

5” (12 cm) disc.

Press PLAY to start play.

Disc tray closes automatically.

4

CLOSE

READING

If an interactive DVD*1 or a
Video CD with playback
control*
MENU appears, go to step 5.

5

2

is used and a TITLE

T I TLE MENU

Cas t l es

Dogs

Love

r

s

Dogs

of the world

• You may also close the tray

by pressing OPEN/CLOSE.

• Data reading time differs with
each disc.

i r

ds

B

3”(8 cm) or

1

<Example>

T I TLE MENU

Dogs

Love

Press or
number key(s) (see

below) to select title
and press SET to
play.

Using number key(s)
starts play automatically.

r

s

2

Cas t l es

B

i r

ds

Press

1

POWER

1

Interactive DVD...

*

May include multiple camera angles,
stories, etc.

2

Video CD with playback control...

*

Particular scenes or information can be
interactively selected from a menu that
appears on the screen.

20

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Press STOP.

6

<Example> 1 digit number 1 ••• 1

Press SKIP | or | to go to next or previous menu screen.

• SKIP function not available with all discs.
Please refer to disc jacket for operation information.

To return to MENU (play stops)
Press TITLE, MENU, or RETURN. (DVD)
Press RETURN. (Video CD)

<Example>

2 digit number 12 •••
3 digit number 123 •••100 1 2 3

Press STOP to stop play.

10 1 2

6

Press OPEN/CLOSE to eject the disc.

7

Important:

*

I

f a remote control button does not work when pressed, press the DVD button on the remote

and try the button again.

■

Forward/Reverse rapid scene
search

➔

Press FF/SLOW+ or REW/SLOW-
during play.

➔

Press PLAY to release.

• Starting forward/reverse search during play
started from menu on Video CDs may recall
menu.

• Search speed, slow at first, increases with
each additional press of the button up to 5
levels.

■

Forward/Reverse Chapter/Track

Skip

➔

Press SKIP

|

or

|

during play.

Each press skips a chapter (DVD) or
track (Video CD/CD).

Pressing | SKIP once midway through a
chapter/track returns to start of that chapter/track.
Each additional press skips back one chapter/
track.

|

• Pressing SKIP
from menu on Video CDs may recall menu.

Chapter/Track Chapter/Track Chapter/TrackChapter/Track

Reverse Skip Forward Skip

■

Still (Pause) Picture

➔

Press STILL/PAUSE during play.

➔

Press PLAY to release.

• DVD/Video CD : The unit will enter Still picture mode.

• CD : The unit will enter Pause mode.

■

Frame by Frame picture

or | during play started

Current playback position

(DVD/Video CD)

➔

Press STILL/PAUSE in Still mode.

➔

Press PLAY to release.

• Each press advances picture one frame.

• Hold down for consecutive frame advance.

• Whether pictures are advanced by “FRAME” or
“FIELD” is selected automatically (see page 61).

■

Slow Motion picture (DVD/Video CD)

➔

Press FF/SLOW+ or REW/SLOW-
(DVD only) in Still mode.

➔

Press PLAY to release.

• Slow motion speed, slow at first, is increased
with each additional press of the button up to 5
levels.

• Reverse slow motion is not available for video
CDs.

• When
is being operated, it means that the
corresponding operation is prohibited by the
unit or the disc.

appears on the screen while a button

RESUME function

The unit memorizes the point where STOP
is pressed (

Press PLAY to resume play from this point.
Pressing STOP again or opening the tray

cancels RESUME, however, RESUME is not
canceled when power is turned off and on.

• RESUME works only with discs for which

elapsed play time is displayed during play.

flashes on screen).

Auto-Power Off function

Power turns off after unit has been in Stop
mode (DVD) for about 5 minutes.

Enjoy Video CDs featuring
playback control without
using menus (Video CDs only)

1.Do steps 1-4 (previous page).

When menu appears, press STOP.

2.Press number key(s) to select desired

track (play begins).

• Check disc for track numbers.

• Press “1” to start at beginning of disc.

To Resume Menu use,
Press STOP, and press PLAY, the menu

screen will be displayed.
Now, go to step 5 (previous page).

Notes

• Please read the disc jacket for operation
information.

• If a single sided disc is placed in upside down,
“PLEASE CHECK THE DISC,
AND FOR STAINS OR SCRATCHES ON
DISC” is displayed.

• Remove disc and press unit POWER off when
not in use.

• Disc continues to rotate with menu displayed
even after play is done. Press STOP to clear
menu display when finished with menu.

Basic Operation

21

TV Operation

Important:

*

If a remote control button does not work
when pressed, press the
the remote and try the button again.

button on

Press POWER* on the remote or unit.

1

Use CH or

0 8

A

BC

2

3

24

number keys to
select a channel.

Press VOL + or VOL -
to adjust volume.

Ready Checklist

All connections are made. (See page 11).
Your unit is plugged in.

VOL + / VOL -

POWER

CH

PHONES
Jack

Using the 100 key

When selecting CABLE channels 100 to 125
with the number keys, first press the 100 key,
and then enter the remaining two digits.

Rapid Tune

Press R-TUNE to display the last channel you

were watching.

Audio Mute

Press MUTE to instantly mute the sound.

Press again to restore the previous sound level.

Phones

Connect an earphone (not supplied) or
headphones (not supplied) to the Phones Jack.

22

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

MTS Broadcast / TV Stereo System

Equipped with ®-TV Noise
Reduction for true MTS
reproduction. ®-TV Noise
Reduction is required for good
stereo separation and audio fidelity.

®

is a registered trademark, and
is licensed by ®Technology
Licensing.

Receivable Broadcast Types

The following are possible audio broadcast types and
on-screen displays. The signal being received is indicated
with an “ ” mark while the selected audio mode is indicated
with an arrow. To change the audio mode for these
broadcasts, see the “Select Audio Mode for TV Viewing”
section (below.)

Press DISPLAY to display

the broadcast signal being received.

MTS Stereo and SAP broadcast

STOP

STER
SAP
M

STOP

STER
SAP
M

STOP

STER
SAP
M

STOP

STER
SAP
M

ONO

ONO

ONO

ONO

1 2 : 0 0A

EO

1 2 : 0 0A

EO

1 2 : 0 0A

EO

1 2 : 0 0A

EO

M

0 : 0 0 : 0 0

M

0 : 0 0 : 0 0

M

0 : 0 0 : 0 0

M

0 : 0 0 : 0 0

ABC

Multi-channel Television Sound Stereo

SP

(main language) and Secondary Audio
Program (sub language) broadcasts are
being received simultaneously.
Select the STEREO or SAP audio mode.

MTS Stereo broadcast

ABC

Multi-channel Television Sound Stereo

SP

broadcast. Select STEREO audio mode.

• If stereo broadcast is weak and the
display flickers, select MONO audio
mode for possibly better results.

SAP broadcast

ABC

Secondary Audio Program

SP

(sub language).
Select SAP audio mode for the sub
language.

ABC

MONO broadcast

SP

Normal monaural sound broadcast.

TV Operation

< Example >

Press AUDIO

Press AUDIO to select the desired audio mode
as described above.

(Arrow shows selection.)

• Each press of AUDIO will change the audio mode as shown

• “SAP” is selected with first press of AUDIO.

STOP

1 2 : 0 0A

STER
SAP
M

ONO

Press AUDIO

M

EO

Audio Mode for TV Viewing

below.

ABC

0 : 0 0 : 0 0

SP

STOP

1 2 : 0 0A

STER

EO
SAP
M

ONO

Press AUDIO

M

0 : 0 0 : 0 0

ABC

SP

STOP

STER
SAP
M

ONO

1 2 : 0 0A

EO

M

0 : 0 0 : 0 0

ABC

SP

23