Panasonic PV-DF274, PV-DF204 User Manual

TV / DVD / VCR Combination

Operating Instructions

Getting Started

Models No.

• Initial Setup and Connection Procedures are on page 18.

PV-DF204/PV-DF274

MULTI FORMAT PLAYBACK

TV Operation VCR

Operation

TV / VCR

Operation

Disc

Information

*Ability to play back may depend on recording conditions.

As an ENERGY STAR® Partner, Matsushita Electric Corporation of America has determined that this product or product model meets the

Please read these instructions carefully before attempting to connect, operate, or adjust this product. Please save this manual. Spanish Quick Use Guide is included. (Guía para rápida consulta en español está incluida.)

This operating instruction book is designed for use with models PV-DF204 and PV-DF274. Illustrations in this manual show the PV-DF274. Fea tures may vary, so please read care ful ly.

ENERGY STAR

guidelines for energy efficiency.

LSQT0798 A

Before Using

Congratulations

On your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you and your family years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your unit.

Date of Purchase _______________

Dealer Purchased From __________

Dealer Address _________________

Dealer Phone No. _______________

Model No. ____________________

Serial No. _____________________

Accessories

Please check and identify the supplied accessories. Use numbers indicated in parentheses when asking for replacement parts.

To order accessories, call toll free 1-800-332-5368.

1 Remote Control (EUR7724030)

Safety Precaution

Be sure to read the following cautions carefully.

WARNING

Never pick unit up by VCR cassette opening.

■ PV-DF274 only

Always grasp bottom and front of unit as shown for proper balance.

To avoid injury to hands, always hold unit by area shown with arrow when resting it on a flat surface.

2 Batteries “AA”

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

The unit may tip or fall if not situated on a stable surface, if pushed, or during an earthquake. Use a strong rope or chain (not included) to fasten the unit firmly to a strong wall support.

Getting Started

TV and VCR Operation

Before Using ..................................................................................2

Safety Precautions .......................................................................4

IMPORTANT SAFEGUARDS AND PRECAUTIONS ....................6

Information (Unit, Cassette) ........................................................8

Information (Disc) .........................................................................9

Location of Controls ...................................................................11

Connections ................................................................................ 14

Initial Setup -Ready to Play- ......................................................18

Tuning TV ..................................................................................... 19

TV Operation ...............................................................................22

MTS Broadcast / TV Stereo System ..........................................24

TV Timer Features .......................................................................25

Closed Caption System ..............................................................26

Video / Audio Menu .....................................................................28

Basic VCR Operation -Playback- ..............................................30

Basic VCR Operation -Record- ..................................................31

Tape Operation ............................................................................32

Timer Recording .........................................................................34

Special VCR Features .................................................................36

Copy Your Tapes (Dubbing) .......................................................38

V-Chip Control Features ............................................................39

Display Feature ...........................................................................45

Getting Started

TV Operation VCR

Operation

TV / VCR

Disc Operation

Information

Basic Disc Operation ..................................................................46

Disc Operation -In PLAY mode- ................................................48

DVD-RAM Operation ...................................................................52

Disc Operation -Using Information Screen- ............................54

Special Disc Operation ..............................................................58

Settings for DVD Operation .......................................................62

Warning and Instruction Displays ............................................67

Before Requesting Service ........................................................68

Spanish Quick Use Guide

Guía rápida de uso en español - Conexión Guía rápida de uso en español - Funcionamiento del televisor Guía rápida de uso en español - Funcionamiento del videograbador Guía rápida de uso en español - Funcionamiento del disco-

Limited Warranty ........................................................................78

Customer Services Directory ....................................................79

Glossa r y ....................................................................................... 80

Specifications .............................................................................81

Index ............................................................................................. 82

..........................................70

............... 71

......73

....................75

Operation

Disc

Information

Safety Precautions

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOIS TURE.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT IN WALL SOCKET. FULLY INSERT.

AVERTISSEMENT :

AFIN DE PRÉVENIR TOUT RISQUE D’INCENDIE OU DE CHOCS ÉLECTRIQUES, NE PAS EXPOSER CET APPAREIL À LA PLUIE OU À UNE HUMIDITÉ EXCESSIVE.

Attention :

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

FCC WARNING :

ANY UNAUTHORIZED CHANGES OR MODIFICATIONS TO THIS EQUIPMENT WOULD VOID THE USER’S AUTHORITY TO OPERATE.

FCC NOTICE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/T V technician for help. You may find the booklet, “Something About Interference” available from FCC local regional offices helpful.

This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org.>

This video recorder, equipped with the HQ (High Quality) System, is compatible with existing VHS equipment. Only use those tapes with the only cassette tapes that have been tested and inspected for use in 2, 4, 6, and 8 hour VCR machines be used. This television receiver provides display of television closed captioning in accordance with §15.119 of the FCC rules.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

mark. It is recommended that

CAUTION:

UNIT IS A CLASS I LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZ ARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED. WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE UNIT YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

Getting Started

CAUTION:

LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.

ATTENTION:

RAYONNEMENT L ASER EN CAS D’OUVERTURE.

NE PAS REGARDER DANS LE FAISCE AU.

(Inside of product)

This symbol warns the user that uninsulated

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS

INSIDE REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL

voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and main te nance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098, and 4,907,093, licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Cor po ra tion. Reverse engineering or dis as sem bly is prohibited.

This television receiver provides display of television closed captioning.

IMPORTANT SAFEGUARDS AND PRE CAU TIONS

WARNING

TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE PRODUCT.

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from power source indicated on

unit or in this manual. If uncer tain, have your Electric Utility Service Company or Video Products Dealer verify your home power source.

2 POWER CORD PLUG

For safety, this unit has a polarized type plug

(one wide blade), or a three-wire grounding type plug. Always hold the plug firmly and make sure your hands are dry when plugging in or unplugging the AC power cord. Regularly remove dust, dirt, etc. on the plug. POLARIZED PLUG CAUTION:

The plug fits into outlet only one way. If it

cannot be fully inserted, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not tamper with the plug. GROUNDING PLUG CAUTION:

The plug requires a three-hole grounding

outlet. If necessar y, have an electrician install the proper outlet. Do not tamper with the plug.

3 POWER CORD

To avoid unit malfunction, and to protect

against electrical shock, fire or personal injury:

- Keep power cord away from heating appliances and walking traffic. Do not rest heavy objects on, or roll such objects over the power cord.

- Do not tamper with the cord in any way.

- An extension cord should have the same type plug (polarized or grounding) and must be securely connected.

- Overloaded wall outlets or extension cords are fire hazards.

- Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified electrician.

4 DO NOT BLOCK VENTILATION

HOLES

Ventilation openings in the cabinet release heat

generated during operation. If blocked, heat build-up may result in a fire hazard or heat damage to cassettes or discs.

For your protection:

a. Never cover ventilation slots while unit is

ON, or operate unit while placed on a bed, sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book

case or rack, unless properly ventilated.

5 AVOID EXTREMELY HOT LOCATIONS

OR SUDDEN TEMPERATURE CHANGES

Do not place unit over or near a heater or

radiator, in direct sunlight, inside closed vehicles, in high temperature locations [over 95 °F (35 °C)], or in over 75 % humidity. If unit is suddenly moved from a cold place to a warm one, moisture may con dense in unit and on the tape causing damage. Never subject unit to vibration, impact, or place it so that the surface is tilted as internal parts may be seriously dam aged.

6 TO AVOID PERSONAL INJURY

• Never place unit on support or stand that is not firm, level, and adequately strong. The unit could fall causing serious injur y to a child or adult and damage to the unit.

• Move any appliance and cart combination with care. Quick stops, excessive force, and uneven surfaces may cause objects to overturn.

• Carefully follow all operating instructions.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

USING THE UNIT

Before unit is brought out of storage or moved to a new location, refer again to the INSTALLATION section of these safe guards.

1 KEEP UNIT WELL AWAY FROM

WATER OR MOISTURE,

such as vases, sinks, tubs, etc.

2 IF EXPOSED TO RAIN, MOISTURE,

OR STRONG IMPACT,

unplug unit and have it inspected by a qualified

service technician before use.

3 ELECTRICAL STORMS

During a lightning storm, or before leaving unit

unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.

4 WHEN UNIT IS PLUGGED IN

• DO NOT OPERATE IF:

- liquid has spilled into unit.

- unit was dropped or otherwise damaged.

- unit emits smoke, odours, or noises. Immediately unplug unit, and have it inspected by a service technician to avoid potential fire and shock hazards.

• Never drop or push any object through openings in unit. Touching internal parts may cause electric shock or fire hazard. Do not put any foreign object on the tray.

• Keep magnetic objects, such as speakers, away from unit to avoid electrical interference.

5 USING ACCESSORIES

Use only accessories recommended by the

manufacturer to avoid risk of fire, shock, or other hazards.

6 CLEANING UNIT

Unplug unit. Use a clean, dry, chemically

untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into unit and cause electrical shock. Any substance, such as wax, adhesive tape, etc. may mar the cabinet sur face. Exposure to greasy, humid, or dusty areas may adversely af fect internal parts.

OUTDOOR ANTENNA INSTALLATION

1 SAFE ANTENNA AND CABLE

CONNECTION

An outside antenna or cable system must be

properly grounded to provide some protection against built up static charges and voltage. Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical Code) provides information regarding proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, con nec tion to grounding electrodes, and requirements for the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH

VOLTAGE POWER LINES OR CIRCUITS

Locate an outside antenna system well away

from power lines and electric light or power circuits so it will never touch these power sources should it ever fall. When installing antenna, absolutely never touch power lines, circuits or other power sources as this could be fatal.

ELECTRIC SERVICE EQUIPMENT

NEC

- NATIONAL ELECTRICAL CODE

GROUND CLAMP

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING C ONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

SERVICE

1 DO NOT SERVICE PRODUCT

YOURSELF

If, after carefully following detailed operating

in struc tions, the unit does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug unit and contact a qualified service tech ni cian.

2 REPLACEMENT OF PARTS

Make sure the ser vice technician uses only

parts specified by the manufacturer, or have equal safety char ac ter is tics as original par ts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.

3 SAFETY CHECK AFTER SERVICING

After unit is serviced or repaired, request that a

thorough safety check be done as described in the manufacturer’s service literature to ensure video unit is in safe operating condition.

Getting Started

Information (Unit, Cassette)

Loading the Batteries

1 Open the

cover.

2 Insert

batteries as marked.

3 Close the

cover.

• Insert so the poles (+ and - ) match those in the remote control.

• Do not use rechargeable type batteries.

Do not:

• Mix old and new batteries.

• Use different types at the same time.

• Heat or expose to flame.

• Take apart or short circuit.

• Attempt to recharge alkaline or manganese batteries.

• Use batteries if the covering has been peeled off.

Mishandling of batteries can cause electrolyte leakage which can damage items the fluid contacts and may cause a fire. Remove if the remote control is not going to be used for a long period of time. Store in a cool, dark place.

Prevent Accidental Tape Era sure

 Break off the tab to protect.

Record Tab

Screw driver

 To record again.

Cover the hole with cellophane tape.

Head Cleaning

Playing older or damaged tapes may eventually cause video heads to become clogged.

 Built-in Head Cleaner

A clean video head helps produce a clear picture. So, we have equipped your unit with a built-in, nonchemical head cleaning system that helps prevent clogging of the video heads. Cleaning is performed each time you load or unload a video cassette.

• This feature is preventative only, If your video heads are seriously clogged, consider the use of a chemical non-abrasive head cleaning kit.

 Head Clog Sensor

During playback this screen appears if clogging is detected. To clear message from screen, press PLAY on the remote or unit.

• Use “dry” type head cleaning cassette only. (Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape directions carefully. Excessive use of head cleaning tape can shorten the video head life.

VIDEO HEADS MAY NEED CLEANING PLEASE INSERT HEAD CLEANING CASSETTE OR REFER TO MANUAL

END:PLAY

DST (Daylight Saving Time)

Unit auto adjusts clock for DST (Daylight Saving Time.)

■ Spring (First Sunday in April)

DST: ON ➞ Sets clock ahead one hour.

■ Autumn (Last Sunday in October)

DST: ON ➞ Turns clock back one hour.

• If your area does not observe Daylight Saving Time, select DST : OFF (see “Manual Clock Setting” on page 20).

• Keep these time changes in mind when pro gram ming the unit for timer recording.

Record/Playback Time

Only use tapes with the mark in this unit.

Tap e

Speed

Setting

SP (Standard Play)

SLP (Super Long Play)

Type of Video Cassette

T60 T120 T160

1 Hour 2 Hours

3 Hours 6 Hours 8 Hours

2 Hours

40 Minutes

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Information (Disc)

Discs that can be played

Disc type Disc Logo

DVD-Video

DVD-R*

DVD-RAM

CD-R

CD-RW

Do not use irregularly shaped discs (e.g. heart-shaped), as these can damage the unit.

*1 DVD-Video formatted discs [finalized].

Discs recorded using Version 1.1 of the Video

Recording Format.

Indication in these operating instructions

DVD-V

(DVD-Video)

DVD-RAM

(CD-DA)

 DVDs that can be played

You can play discs with these symbols.

 Playing DVDs

The producer of these discs can control how they are played so you may not always be able to control play as described in these operating instructions. Read the disc’s instructions carefully.

 DVD-R discs

Panasonic DVD-R recorded and finalized* on a Panasonic DVD video recorder are played as DVD-Video on this unit.

DVD-RAM discs

DVD-RAM discs must meet the following conditions for this unit to be able to play them.

• Non-cartridge discs

Type

Capacity

• Remove TYPE 2 and 4 discs from their cartridges before use, then return them when you are finished. Read the instructions for the disc carefully.

• Discs that can be removed from their car tridges (T YPE 2 and 4)

• 12 cm (5″) 9.4 GB (double-sided) and 4.7 GB (single-sided)

• 8 cm (3″) 2.8 GB (double-sided)

TYPE 2 or 4 disc

Non-cartridge disc

Getting Started

 Discs that cannot be played

DVD with Region No. other than “1” or “ALL”, DVD from PAL system, DVD-ROM, DVD+R, DVD-AUDIO, DVD-RW, DVD+RW, CD-ROM, CDV, CVD, CD-G, CD-TEXT, SACD, Photo-CD,

Note

• It may not be possible to play CD-R, CD-RW, DVD-R and DVD-RAM in all cases due to the type of disc or condition of the recording.

Video CD.

• Some parts of the disc, for example where one program ends and another begins, may not play smoothly.

 CD-R and CD-RW discs

This unit can play CD-R and CD-RW if they are formatted as CD-DA (digital audio) and finalized*.

*A process that allows play on compatible equipment.

Disc Handling

Handling precautions

• Sticking a label on the disc may impair DVD-R playback.

• Do not attach sticker to disc. (Do not use discs with exposed adhesive from tape or left over peeled-off stickers.)

• Only hold disc by edges as shown below. Fin ger prints, dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning sprays, benzine, thinner, static electricity prevention liquids, or any other solvent.

• Do not try to close disc tray when disc is not properly placed.

Disc tray

Disc

Region Management Information

This unit is designed and man u fac tured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not cor re spond to the Region number of this unit, this unit cannot play this disc.

For U.S.A. and Canada

• The region number of this player is “1”.

• The player will play DVD-Video marked with

labels bearing “1” or “ALL”.

Example:

ALL

To clean disc surface

With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.)

• DVD-RAM, DVD- R : Clean only with the DVD-RAM disc cleaner

available. Never use cloths or cleaners for CDs, etc.

If disc is brought from a cold to a warm environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.)

Improper disc storage

Discs can be damaged if stored or left in these environment:

• Exposed to direct sunlight.

• Areas that are humid or dusty.

• Near heat (i.e. heater, radiator, etc.).

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Location of Controls

Remote Control Buttons

1 2

12 13 14

When this button is pressed in TV / VCR mode, the tape is

OPEN / CLOSE /

EJECT

POWER Turns the unit on or off.

DISPLAY

RAPID TUNE

MUTE Mutes the sound instantly.

INPUT Changes input source.

ACTION Displays Main Menu.

SELECT ▲▼◄ ►

ejected. This button is inoperative if pressed during recording. If pressed in DVD mode, the disc tray opens or closes.

Displays the TV status and clock. In DVD mode, displays disc and unit information.

Displays the last channel you were watching.

Controls navigation around on-screen menu.

28 29

CHANNEL

UP/DOWN

REW/SLOW-

STOP Stops rec ording or playback.

STILL/PAUSE

SKIP- /

AUDIO Selects the desired audio mode.

ANGLE

REC Records a program.

PROGRAM

DVD Set to DVD mode.

TV/VCR Sets to TV/VCR mode.

TRACKING UP /

DOWN NUMBER Keys Selects a channel directly.

ADD/DELETE/

CLEAR MENU / PLAY

LIST SET Sets selected menu.

VOLUME

UP/DOWN PLAY Begins playback.

FF/SLOW+

TITLE / D.NAVI

SKIP+ / CM SKIP / ZERO

SURROUND / VSS

SUB TITLE

ZOOM/

COUNTER RESET

SPEED / RETURN

Selects a channel.

Rewinds tape and searches previous scene. Decreases slow motion speed in Still mode.

Pauses picture in Playback mode and frame advance picture in Still mode.

Skips back one chapter or track. Goes to previous menu screen. Goes directly to the desired recording.

Selects the desired angle in DVD mode.

Displays SET PROGR AM screen. You can set Timer Program and On-Timer.

Reduces picture noise during Playback and Slow Motion.

Adds or deletes a channel. Cancels an item on the screen.

Displays DVD menu. Displays Play List. (DVD- RA M)

Adjusts volume.

Fast forwards tape and searches next scene. Increases slow motion speed in Still mode.

Selects the desired title by number on some DVDs. Displays Direct Navigator. (DVD-RAM).

Skips one chapter or track. Goes to next menu screen. In Stop mode, goes to the c ounter “0: 00:00”. In Playback mode, skips over 1 to 3 minutes of tape.

Creates a deeper, 3-D sound effect.

Selects a different subtitle language.

Enlarges specific portions of DVD picture. Resets to “ 0:00: 00” at desired portion of tape.

Returns to DVD menu screen. Selects recording speed of tape.

Getting Started

Unit Buttons

Front View

8' 14'

23 4

789101112

141516171819202122 24

Built In Speakers Equipped with 2 front speakers.

Audio Input

Connector 2 Disc Tray Place compatible discs here.

Cassette

Compartment

Phones Jack

Video Input

Connector 2 POWER Turns the unit on or of f.

STOP Stops playback.

STILL

DVD Operation

(PV-DF204

only) PLAY Begins playback.

SKIP ◄◄

SKIP►►

OPEN/CLOSE Opens or closes the disc tray.

VOLUME

UP/DOWN CHANNEL

UP/DOWN or

TRACKING UP/DOWN

INPUT (PV-DF204-K

14'

only)

Connect from other component. (LINE 2)

Insert VHS tapes here.

Connect an ear phone or headphones.

Connect from other component. (LINE 2)

Pauses picture in Playback mode and frame advance picture in Still mode.

Skips back one chapter or track. Goes to previous menu screen.

Skips one chapter or track. Goes to next menu screen.

Adjusts volume.

Selects a channel. Reduces picture noise during Playback and Slow Motion.

Changes input source.

STOP/

EJECT

VCR Operation

PLAY/

REPEAT

REWIND/

FAST FORWARD/

SEARCH REC Records a program.

Remote Sensor

REC Indicator

(RED)

ON TIMER Indicator

(ORANGE)

PROG TIMER Indicator

(GREEN)

ANGLE Indicator

(RED)

STOP: Stops playback. EJECT: Ejects the tape.

PLAY: Begins playback. REPEAT: Sets to see a recording over and over.

Rewinds tape and searches previous scene. Decreases slow motion speed in Still mode.

Fast forwards tape and searches next scene. Increases slow motion speed in Still mode.

Receives infrared signal from remote control.

Lights up during recording. In Rec Pause or OTR Pause mode, the Indicator flashes.

Lights when the On Timer is set.

Lights up when the unit is set for Timer Recording. It flashes when a Timer Recording has been set with no tape inserted, the clock is not set, or the tape is in motion. Lights up when the On Timer is set.

Lights up when a scene recorded multiple angles is detected. (DVD only)

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Rear View

1 AC Power Plug

Optical digital audio output

connector Audio Output Connector

(L/R)

4 Audio Input Connector 1

5 Video Input Connector 1

Getting Started

12 3 45 6

When plugged into an AC outlet, this unit consumes 1.5 W of electric power in OFF condition.

Outputs audio signal. (Digital)

Outputs audio signal. (Analog)

Connect from other component. (LINE 1)

VHF/UHF Antenna

Input Terminal

Input terminal for an antenna or cable box signal.

Connections

Notes on con nec tions

• Turn off the power supply for all com po nents before making any connections.

• If the cables necessary for connecting a component to the system are not included with the component or available as an option, you may need to fashion a cable to suit the component concerned.

• Read the instruction manual for each system component care ful ly before connecting it.

Connecting the RF in Terminal

CAUTION

Overtightening “Nut type” RF coaxial cables may damage jacks. Finger tighten only.

 Antenna Connection

Connect the cable from Antenna to the VHF/UHF terminal on the unit.

VHF Antenna

Mixer

UHF Antenna

 Cable Connection

Connect the cable supplied by your local cable company to VHF/UHF terminal on the unit.

Note to CABLE system installer:

This re mind er is pro vid ed to call the CABLE (Cable TV) System Installer’s at ten tion to Article 820- 40 of the NEC that pro vides guide lines for proper grounding and, in par tic u lar, specifies that the cable ground shall be con nect ed to the ground ing system of the build ing, as close to the point of cable entry as practical.

In from CABLE

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Cable Box

Connecting the “1, 2” AV Input Terminals

Connects VCRs and other peripheral equipment

 AV Input terminal 1 is used

Getting Started

Video

OUT

Audio

OUT

Notes

• Similar connections are available at the “1, 2” AV input terminals.

• AV Input terminal 2 is located on the front of the unit.

Connecting the Audio Output Terminal

Enjoy the powerful movie theater and hall-like sound available with multiple channel audio found on DVDs by connecting an amplifier and speakers. There are two types of connection, digital and analog.

 Analog connection Digital connection

Connect an amplifier with Dolby Digital or DTS decoders to enjoy surround sound.

Connect an amplifier to enjoy high-quality stereo sound with sampling frequencies of 96 kHz.

Firmly connect the cable to the connector.

OPTICAL

Amplifier with built in Dolby Digital or DTS decoders.

Speakers (example)

Please see amplifier manual for speaker requirements.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Amplifier

Speakers (example)

Check List

Turn down the volume, then turn this unit, as

well as other equipment to be connected, off before pro ceed ing with connection.

Do not block ventilation holes of any equipment

and arrange it so that air can circulate freely.

Enjoying digital audio output from the digital audio output con nec tor

Notes on audio output from the optical digital audio output con nec tor

Disc

DVD-V

DVD-RAM

Sound recording format

Dolby Digital

Linear PCM (48/96 kHz 16/20/24 bi t)

dts

Dolby Digital

Linear PCM (48 kHz 16 bit)

Linear PCM

*1 The type of audio output from the connector can

be selected by adjusting the Settings for DVD Operation. (See pages 64-65.)

*2 When "LPCM" is set to OFF in the DVD Main

Menu, only 48 kHz sampling/16 bit is output. When set to ON, sampling of sound quality greater than 48 kHz/16 bit is reduced to 48 kHz/16 bit. (See pages 64-65.)

Manufactured under license from Digital Theater Systems, Inc. US Pat. No’s. 5,451,942, 5,956,674, 5,974,380, 5,978,762, 6,487,535 and other U.S. and world-wide patents issued and pending. “DTS” and “DTS 2.0 + Digital Out” are trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Reserved.

Optical digital audio output from connector

Dolby Digital bitstream (1-5.1 ch) or PCM (48 kHz sampling/16 bit only)*

Linear PCM (2ch) (48 kHz sampling/16 bit

only)*

Bitstream or PCM (4 8 kHz sampling/16 bit only)*

Dolby Digital bitstream (1-5.1 ch) or PCM (48 kHz sampling/16 bit only)*

Linear PCM (2ch)

Linear PCM (44.1 kHz sampling)

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be ef ficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic Surround Sound Decoders please contact your local dealer.

IMPORTANT NOTE:

Caution for optical digital audio output connector:

• When connecting an amplifier (with an optical digital input connector) which does not contain the Dolby Digital or dts decoder, be sure to select “PCM” at “Dolby Digital” and “PCM” at “dts” in the Settings for DVD Operation “Selecting AUDIO OUTPUT” (see pages 64-65). Other wise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers.

• Be sure to refer to pages 64-65 regarding output settings of Dolby Digital, dts, and PCM.

• CDs can be played as usual.

Note

• Some dts decoders which do not support DVD-dts Interface may not work properly with the unit.

Getting Started

Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories.

Initial Setup -Ready to Play-

EJECT

POWER

ACTION

SELECT

▲▼◄ ►

SET

STOP

POWER

STOP

Initial Setup (Ready to Play)

Please make all cable or antenna connections before powering on. Plug the unit power cord into an AC wall outlet.

• Function buttons are void during Initial Setup.

• To eject a tape during Auto Set, press EJECT on remote. Then make settings manually. (See pages 19-21.)

• If Auto Clock Set takes more than 30 minutes, press STOP and perform settings manually. (See pages 19-21.)

Case 1

Settings are made automatically. When complete, this screen appears.

10/25/2004 MON 11:45AM

SETTING : CH 10

AUTO CLOCK SET

DST:ON

COMPLETED

Case 2

If setup is incomplete, the following screen appears. Check connection of Antenna/Cable to the RF in Terminal, then

AUTO CLOCK SET

IS INCOMPLETE

PLEASE SET CLOCK BY PRESSING ACTION KEY

try to manually set the clock as follows.

a. Press ACTION on the Remote to

display SET CLOCK Menu screen.

SET CLOCK

1/ 1/2004 THU 12:00AM

DST:ON

Press POWER on the remote or unit. Auto channel and clock set starts.

• If you use a cable box, turn it on and set it to the Public Broadcasting Service (PBS) channel in your time zone. If you use a DSS receiver, it must be turned of f.

CH AUTO SET PROCEEDING

AUTO CLOCK SET

PROCEEDING

CANCEL:STOP

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

SELECT: SET:SET START :ACTION

b. Press ▲▼ to select the month and

press SET to set. In the same manner, select and set the date, year, time, and DST (Daylight Saving Time).

• Press ◄ repeatedly to move the cursor. Press ▲▼ to make a correction.

SET CLOCK

10/25/2004 MON 11:45AM

SELECT: SET:SET START :ACTION

DST:ON

c. Press ACTION twice to start CLOCK

and exit.

Tuning TV

ACTION SELECT

▲▼◄ ►

CH▲▼

NUMBER keys

ADD/DLT

SET

4 Press ▲▼ to select “ANTENNA,” then

press SET to set your antenna system (“TV” or “CABLE”).

5 Press ▲▼ to select “AUTO SET,”

then press SET.

• After Channel Auto Set is finished, Clock Auto Set will be per formed. (If clock is set manually, Clock Auto Set will not be per formed.)

Add or Delete a Chan nel

 To add channel :

Select channel with NUMBER keys and press ADD/DLT.

CHANNEL 08 ADDED

TV Operation

Automatic Channel Setting

1 Press ACTION to display MAIN

MENU.

2 Press ▲▼◄ ► to select “CH.”

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

3 Press SET.

SET UP CHANNEL

ANTENNA : CABLE

AUTO SET WEAK SIGNAL DISPLAY:OFF

SELECT: SET:SET END :ACTION

 To delete chann el:

Select channel with CH ▲▼ or NUMBER keys and press ADD/DLT.

CHANNEL 08 DELETED

ACTION

SELECT

▲▼◄ ►

SET

POWER

PLAY/REPEAT

Automatic Clock Setting

1 Press ACTION to display MAIN

MENU.

Manual Clock Setting

1 Press ACTION to display MAIN

MENU.

2 Press ▲▼◄ ► to select “CLOCK.”

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

3 Press SET.

(“TIME ZONE ADJUST” appears only when auto clock is set.)

SET CLOCK

AUTO CLOCK SET

MANUAL

TIME ZONE ADJUST : 0

SELECT: SET:SET END :ACTION

4 Press ▲▼ to select “MANUAL,” then

press SET.

SET CLOCK

10/25/2004 MON 11:45AM

DST:ON

2 Press ▲▼◄ ► to select “CLOCK.”

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

3 Press SET.

SET CLOCK

AUTO CLOCK SET

MANUAL

SELECT: SET:SET END :ACTION

4 Press ▲▼ to select “AUTO CLOCK

SET,” then press SET.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

SELECT: SET:SET END :ACTION

5 Press ▲▼ and press SET to select

and set the month, date, year, time, and DST (Daylight Saving Time).

To Make Corrections, repeatedly

press ◄ to move to error, then correct.

6 Press ACTION twice to start the

clock and exit this mode.

Time Zone Adjust

(Only when Auto Clock is set.)

1 Press ▲▼◄ ► to select “CLOCK.”

MAIN MENU

DVD LOCK LANGUAGE

3 Press SET repeatedly.

English Spanish

French

For Engl ish

MAIN MENU

TV CLOCK CH

SELECT: SET:SET END :ACTION

2 Press SET.

SET CLOCK

AUTO CLOCK SET MANUAL

TIME ZONE ADJUST : 0

SELECT: SET:SET END :ACTION

3 Press ▲▼ to select “TIME ZONE

ADJUST” and press SET to subtract or add hour(s) as necessary.

SET CLOCK

AUTO CLOCK SET MANUAL

TIME ZONE ADJUST :+1

SELECT: SET:SET END :ACTION

-1

4 Press ACTION twice to exit.

Note

• “TIME ZONE ADJUST” returns to “0” if clock is set manually.

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

For Spanish

MENU PRINCIPAL

DVD BLOQUEO IDIOMA

TV RELOJ CANAL

ELEGIR: FIJAR:SET TERMINAR:ACTION

For Fr ench

DVD BLOCAGE LANGUE

TELE HORLOGE CANAL

SEL.: REGLER:SET FIN :ACTION

4 Press ACTION to exit.

Reset all unit Memory Func tions

Returns to factory setting. Use if relocating unit, or if Initial Setup needs to be redone.

• Make sure a tape is not inserted in unit.

TV Operation

Change Language Setting

1 Press ACTION to display MAIN

MENU.

2 Press ▲▼◄ ► to select “LANGUAGE.”

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

1 Turn the unit Power on.

2 Press and hold both PLAY/REPEAT

and FF on the unit for more than 5 seconds.

• The power will shut off.

• Please ignore “NO CASSETTE” warning.

3 Perform “Initial Setup” on page 18.

TV Operation

RAPID TUNE

MUTE INPUT ACTION

SELECT

▲▼◄ ►

CH▲▼

NUMBER keys

100 key

SET

VOL+/-

 Method 2:

Press INPUT. The display will change as follows.

LINE1

LINE2

TUNER

 Method 3:

1 Press ACTION for MAIN MENU. 2 Press ▲▼◄ ► to select “TV”, then

press SET for SET UP TV screen.

SURROUND

AV Input Terminal 2

If a remote control button does not work when pressed, press the TV/VCR button on the remote and try the button again.

Selecting Input Mode

 Method 1:

Press CH ▲▼. The display will change as follows.

Notes

• The diagram at right is an example.

• T V CH 2 and CABLE CH 1 represent the lowest channels in memory, while TV CH 69 and CABLE CH 125 represent the highest channels in memory.

(TV)

CH2

(CABLE)

CH1

(TV)

CH69

(CABLE)

CH125

LINE2

LINE1

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

3 Press ▲▼ to select “INPUT SELECT,”

and then press SET to select “TUNER”, “LINE 1”, or “LINE 2.”

SET UP TV

CAPTION

INPUT SELECT :TUNER

SET UP VIDEO/AUDIO DVD VOL ADJUST :+2

SELECT: SET:SET END :ACTION

4 Press ACTION twice to exit this

mode.

LINE 1:

Signal of source connected to AV Input terminal 1 is displayed. (

Rear of the unit.)

LINE 2:

Signal of source connected to AV Input terminal 2 is displayed.

TUNER:

Signal of source connected to VHF/UHF terminal is displayed.

Using the CH/VOL Button

Select desired channel:

Press CH ▲▼ or NUMBER keys.

Adjust desired volume level:

Press VOL + or VOL -.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Using the Number and 100 keys

When selecting CABLE channels 100 to 125 with the NUMBER keys, first press the 100 key, and then enter the remaining two digits.

Example 1:

To select channel 125, first press the 100 key, then 2, then 5.

Example 2:

To select channel 12, first press the 1 key, then 2.

Example 3:

To select channel 2, first press the 0 key, then 2.

Rapid Tune

Press R-TUNE to display the last channel you were watching.

Audio Mute

Press MUTE to instantly mute the sound. Press again to restore the previous sound level.

Surround Sound System

You can hear a deeper, 3-D sound effect using just the unit’s two front speakers.

Weak Signal Display Feature

When “ON” is selected, the picture is displayed even when a broadcast signal is weak or non-existent.

1 Press ACTION to display MAIN

MENU. 2 Press ▲▼◄ ► to select “CH.” 3 Press SET to display SET UP

CHANNEL screen.

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET END :ACTION

4 Press ▲▼ to select “WEAK SIGNAL

DISPLAY.”

5 Press SET to set “ON” or “OFF.”

SET UP CHANNEL

ANTENNA : CABLE AUTO SET

WEAK SIGNAL DISPLAY:OFF

SELECT: SET:SET

ON:

Picture is displayed regardless of signal condition, and may not always be clearly visible.

OFF:

Screen turns solid blue when signal is absent or weak.

Note

• If unit is connected to equipment which has blue back feature, selecting “ON” will have no effect on the other equipment.

END :ACTION

TV Operation

Press SURROUND.

•”SURROUND ON” is displayed.

To Cancel, press SURROUND.

Notes

• Surround sound effect is not available for normal (mono) broadcasts.

• The surround effect (TV, VCR mode only) is not output to Audio Output L/ R Connector.

6 Press ACTION twice to return to the

normal screen.

MTS Broadcast / TV Stereo System

Receivable Broadcast Types

DISPLAY

AUDIO

Equipped with -TV Noise Reduction for true MTS reproduction.

-TV Noise Reduction is required for good stereo separation and audio fidelity.

is a

registered trademark, and is licensed by

Techn o l o g y L ic e nsing.

Audio Mode for TV Viewing

Press AUDIO to select the desired audio mode as described above. (Arrow shows selection.)

• Each press of AUDIO will change the audio mode as shown below.

• “SAP” is selected with first press of AUDIO.

< Example >

12:00AM CH 08

STEREO SAP MONO

12:00AM CH 08

STEREO SAP MONO

12:00AM CH 08

The following are possible audio broadcast types and on-screen displays. The signal being received is indicated with a “ while the selected audio mode is indicated with an arrow. To change the audio mode for these broadcasts, see the “Audio Mode for TV Viewing” section.

Press DISPLAY to display the broadcast signal being received.

MTS Stereo broadcast:

Multi-channel Television Sound Stereo broadcast. Select STEREO audio mode.

• If stereo broadcast is weak and the display flickers, select MONO audio mode for possible improvement.

SAP broadcast:

Secondary Audio Program (sub language). Select SAP audio mode for the sub language.

MTS Stereo and SAP broadcast:

Multi-channel Television Sound Stereo (main language) and Secondary Audio Program (sub language) broadcasts are being received simultaneously. Select the STEREO or SAP audio mode.

MONO broadcast:

Normal monaural sound broadcast.

12:00AM CH 08

STEREO SAP MONO

12:00AM CH 08

STEREO SAP MONO

12:00AM CH 08

STEREO SAP MONO

12:00AM CH 08

STEREO SAP MONO

” mark

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

TV Timer Features

DISPLAY

ADD/DLT

SELECT

▲▼◄ ►

PROG

SET

ON-TIMER Indicator

ON-TIMER

This unit can be set to automatically power on in one of 3 modes (TV, VCR Playback, or Disc.)

1 Press PROG to display SET

PROGRAM screen.

2 Press ▲▼ to select “ON TIMER.” 3 Press SET to display ON TIMER

screen.

4 Press ▲▼ to select desired settings. 5 Press SET to set the ON-TIMER time

and ON-TIMER mode.

SET PROGRAM

TIMER PROGRAMMING

ON TIMER

SLEEP TIMER: 0

SELECT: SET:SET END :PROG

ON TIMER

10:--AM CH --

SELECT: SET:SET END :PROG

• Make sure a tape is inserted if Playback mode is selected.

• Make sure a disc is inserted if Disc (DVD/CD) mode is selected.

Lowest channel

Highest channel

ON-TIMER mode selection order

CH01

CH125

Disc

VCR

To Make Corrections, use ▲▼ and ◄ ► to move back and correct.

6 Press PROG to

set ON TIMER.

• “ON TIMER SET” is displayed.

• PROG TIMER Indicator lights up on the unit.

ON TIMER

10:00AM CH 05

CANCEL:ADD/DLT SELECT: SET:SET END :PROG

To Cancel ON-TIMER,

Repeat steps 1-3. Then, press ADD/DLT to clear the time in steps 4-5. Now, press PROG to end. “ON TIMER END” briefly appears on-screen.

Note

• If no button on the remote or unit is pressed within 60 minutes after unit turns itself on, it will turn itself back off.

Sleep Timer

This unit can be set for auto power off.

1 Press PROG to display SET

PROGRAM screen. 2 Press ▲▼ to select “SLEEP TIMER.” 3 Press SET repeatedly to select the

desired time.

30 60

0 90

To cancel, press SET repeatedly until 0 appears.

4 Press PROG to return to the normal

screen.

• Pressing DISPLAY with sleep timer set displays remaining time.

SET PROGRAM

TIMER PROGRAMMING ON TIMER

SLEEP TIMER: 0

SELECT: SET:SET END :PROG

TV Operation

Closed Caption System

MUTE

ACTION

SELECT

▲▼◄ ►

Closed Caption is ...

This multi-use system not only allows the hearing impaired to enjoy selected programs, but also allows one to watch programs with the volume muted.

Closed Caption Mode Feature

1 Press ACTION to display MAIN

MENU.

2 Press ▲▼◄ ► to select “TV.”

SET

MAIN MENU

DVD LOCK LANGUAGE

4 Press ▲▼ to select “CAPTION”. 5 Press SET to display CAPTION

screen.

SET UP TV

CAPTION

INPUT SELECT :TUNER SET UP VIDEO/AUDIO DVD VOL ADJUST :+2

SELECT: SET:SET END :ACTION

6 Press ▲▼ to select “CAPTION

MODE.”

7 Press SET repeatedly to select mode.

CAPTION

CAPTION MODE : OFF

CC ON MUTE : CAP C1

SELECT: SET:SET END :ACTION

OFF CA P C1

TEXT C2 CAP C2 TEXT C1

Caption Mode: CAP C1 or C2

A narration of selected TV programs is displayed. Check TV program listings for CC (Closed Caption) broadcasts.

Caption Mode: TEXT C1 or C2

Most of the screen will be blocked out. When the TV station broadcasts information, such as program listings, it will appear in this space.

Caption Mode: OFF

Closed Caption/Text narration will not be displayed.

8 Press ACTION three times to return

to the normal screen.

TV CLOCK CH

SELECT: SET:SET END :ACTION

3 Press SET to display SET UP TV

screen.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Note

• The closed caption or text signal may be broadcast over C1, C2, or both. Also, text contents can vary so you may wish to try different settings.

+ 58 hidden pages

Panasonic PV-DF274, PV-DF204 User Manual

Before Using

Table of Contents

Safety Precautions

IMPORTANT SAFEGUARDS AND PRE CAU TIONS

Information (Unit, Cassette)

Information (Disc)

Location of Controls

Connections

Initial Setup -Ready to Play-

Tuning TV

TV Operation

MTS Broadcast / TV Stereo System

TV Timer Features

Closed Caption System