Panasonic PV-DC352K, PV-DC352 Operating Instructions

Digital Video Camcorder

Operating Instructions

Models No. PV-DC352

PV-DC352-K

Mini

Before attempting to connect, operate or adjust this product, please read these instructions thoroughly. Spanish Quick Use Guide is included.

Guía para rápida consulta en español está incluida.

For USA assistance, please call: 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com

For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca

LSQT0561A

Things You Should Know

Date of Purchase

Thank you for choosing Panasonic!

You have purchased one of the most sophisticated and reliable products on the market today. Used properly, we’re sure it will bring you and your family years of enjoyment. Please take time to fill in the information on the right. The serial number is on the tag located on the underside of your Palmcorder. Be sure to retain this manual as your convenient Palmcorder information source.

Dealer Purchased From

Dealer Address

Dealer Phone No.

Model No.

Serial No.

Safety Precautions

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

Your It is recommended that only cassette tapes that have been tested and inspected for use in Palmcorder with the

Palmcorder is designed to record and play back in Standard Play (SP) mode and Long Play (LP) mode.

mark be used.

This symbol warns the user that uninsulated

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

The above markings are located on the appliance bottom cover.

Note: This equipment has been tested and found to comply with Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. You may find the booklet, ‘Something About Interference’ available from FCC local regional offices helpful.

FCC Warning:

≥To assure continued FCC compliance, the user must use only the provided shielded interfacing cable with ferrite core when

connecting the digital Palmcorder to computer in accordance with instruction herein. Also, any unauthorized changes or modifications to this equipment could void the user’s authority to operate.

Declaration of Conformity

Model No.: PV-DC352 Trade Name: Panasonic Responsible party: Matsushita Electric Corporation of America Address: One Panasonic Way, Secaucus, New Jersey 07094 Telephone number: 1-800-211-PANA (7262)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: TO PREVENT FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR

≥Since this product gets hot during use, operate it in well ventilated place; do not install this equipment in a confined space such

as a bookcase or similar unit.

ACCESSORIES ONLY.

EQUIVALENT TYPE.

11) Grounding or Polarization— This video unit may be

Important Safeguards

1) Read Instructions— All the safety and operating instructions should be read before the unit is operated.

2) Retain Instructions— The safety and operating instructions should be retained for future reference.

3) Heed Warnings— All warnings on the unit and in the operating instructions should be adhered to.

4) Follow Instructions— All operating and maintenance instructions should be followed.

5) Cleaning— Unplug this video unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a dry cloth for cleaning.

6) Attachments— Do not use attachments not recommended by the video product manufacturer as they may be hazardous.

7) Water and Moisture— Do not use this video unit near water- for example near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

8) Accessories— Do not place this video unit on an unstable cart, stand, tripod, bracket, or table. The video unit may fall, causing serious injury to a child or adult, and serious damage to the unit. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video unit. Any mounting of the unit should follow the manufacturer’s instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven

equipped with either a polarized 2-wire AC (Alternating Current) line plug (a plug having one blade wider than the other) or 3-wire grounding type plug, a plug having a third (grounding) pin. The 2-wire polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. The 3-wire grounding type plug will fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug.

12) Power-Cord Protection— Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords of plugs, convenience receptacles, and the point where they exit from the unit.

13) Outdoor Antenna Grounding— If an outside antenna or cable system is connected to the video unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Part 1 of the Canadian Electrical Code, in USA Section 810 of the National Electrical Code, provides information with respect to proper grounding of the mast and supporting structure, grounding of the leadin wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

surfaces may cause the appliance and cart combination to overturn.

9) Ventilation— Slots and

S3125A

openings in the cabinet are provided for ventilation and to ensure reliable operation of the video unit and to protect it from overheating. These openings must not be blocked or covered. Never place the video unit on a bed, sofa, rug, or other similar surface, or near or over a radiator or heat register. This video unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

10) Power Sources— This video unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For video units intended to be operated from battery power, or other sources, refer to the operating instructions.

NEC - NATIONAL ELECTRICAL CODE

14) Lightning— For added protection of this video unit receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video unit due to lightning and power-line surges.

15) Power Lines— An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16) Overloading— Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

ELECTRIC SERVICE EQUIPMENT

GROUND CLAMP

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810 - 20)

GROUNDING CONDUCTORS (NEC SECTION 810 - 21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PARTH)

Important Safeguards

17) Objects and Liquids — Never push objects of any kind into this video unit through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind onto the video unit.

18) Servicing — Do not attempt to service this video unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19) Damage Requiring Service — Unplug this video unit from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If any liquid has been spilled into, or objects have

fallen onto, the video unit. c. If the video unit has been exposed to rain or water. d. If the video unit does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions, as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the video unit to its

normal operation. e. If the video unit has been dropped or the cabinet has

been damaged. f. When the video unit exhibits a distinct change in

performance — this indicates a need for service.

20) Replacement Parts — When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

21) Safety Check— Upon completion of any service or repairs to this video unit, ask the service technician to perform safety checks to determine that the video unit is in safe operating order.

Precautions

USE & LOCATION

≥TO AVOID SHOCK HAZARD ... Your Palmcorder and

≥DO NOT AIM YOUR PALMCORDER AT THE SUN OR

≥DO NOT LEAVE THE PALMCORDER WITH THE EVF

≥DO NOT EXPOSE YOUR PALMCORDER TO

≥AVOID SUDDEN CHANGES IN TEMPERATURE ... If the

≥DO NOT LEAVE YOUR PALMCORDER OR THE POWER

≥STORAGE OF YOUR PALMCORDER ... Store and handle

CARE

≥TO CLEAN YOUR PALMCORDER ... Do not use strong or

≥TO PROTECT THE LENS ... Do not touch the surface of

≥TO PROTECT THE FINISH OF YOUR PALMCORDER ...

power supply should not be exposed to rain or moisture. Do not connect the power supply or operate your Palmcorder if it gets wet. Your Palmcorder has been designed for outdoor use, however it is not designed to sustain direct exposure to water, rain, sleet, snow, sand, dust, or a direct splashing from a pool or even a cup of coffee. This action could permanently damage the internal parts of your Palmcorder. Do not attempt to disassemble this unit. There are no user serviceable parts inside. Unplug your Palmcorder from the power supply before cleaning.

OTHER BRIGHT OBJECTS

AIMED DIRECTLY AT THE SUN AS THIS MAY CAUSE DAMAGE TO THE INTERNAL PARTS OF THE EVF

EXTENDED HIGH TEMPERATURE ... Such as, in direct

sunlight, inside a closed car, next to a heater, etc... This action could permanently damage the internal parts of your Palmcorder.

unit is suddenly moved from a cold place to a warm place, moisture may form on the tape and inside the unit.

SUPPLY TURNED ON WHEN NOT IN USE.

your Palmcorder in a manner that will not subject it to unnecessary movement (avoid shaking and striking). Your Palmcorder contains a sensitive pick-up device which could be damaged by improper handling or storage.

abrasive detergents when cleaning your Palmcorder body.

the lens with your hand. Use a commercial Palmcorder lens solution and lens paper when cleaning the lens. Improper cleaning can scratch the lens coating.

Before handling your Palmcorder, make sure your hands and face are free from any chemical products, such as suntan lotion, as it may damage the finish.

This class B digital apparatus complies with CANADIAN ICES-003.

This Product has fluorescent lamps that contain a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org

U.S.A./CANADA CONSUMERS: ATTENTION:

A lithium ion/polymer battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery.

Contents

Before Using

Standard Accessories ......................................................... 6

Quick Guide......................................................................... 7

To View the Playback Picture.............................................. 7

Controls and Components................................................... 8

Remote Controller............................................................. 10

Power Supply .................................................................... 12

Charging Time and Available Recording Time.................. 12

Lens Cap and Grip Belt ..................................................... 13

Attaching the Shoulder Strap ............................................ 14

Inserting a Cassette .......................................................... 14

Turning on/off the Palmcorder and Selecting Modes ........ 15

Using the Viewfinder ......................................................... 15

Using the LCD Monitor ...................................................... 15

Using the Menu Screen..................................................... 16

List of Menus..................................................................... 17

Setting Date and Time....................................................... 20

Internal Lithium Battery Recharge..................................... 20

LP Mode............................................................................ 20

Audio Recording Mode...................................................... 20

CAMERA Mode

Recording.......................................................................... 21

PhotoShot Recording on the DV Cassette........................ 22

Zoom In/Out Functions...................................................... 22

Digital Zoom Function ....................................................... 23

Digital Electronic Image Stabilizer Function...................... 23

Fade In/Out Functions....................................................... 23

Cinema Function............................................................... 24

Backlight Compensation Function..................................... 24

MagicPix Function............................................................. 24

Quick Start......................................................................... 25

Wind Noise Reduction Function ........................................ 25

Recording in Special Situations (Program AE).................. 25

Manual Shutter Speed Adjustment.................................... 26

Manual Iris Adjustment (F Number) .................................. 26

Manual Focus Adjustment................................................. 26

Recording in Natural Colors (White Balance).................... 27

Adjusting White Balance Manually .................................... 27

Using the Free Angle Flash............................................... 28

Digital Effect Functions...................................................... 29

VCR Mode

Playing Back...................................................................... 31

Finding a Scene You Want to Play Back........................... 31

Slow Motion Playback ....................................................... 32

Still Playback/Still Advance Playback................................ 32

Finding the End of a Recording

(Blank Search Function)................................................ 32

Index Search Functions..................................................... 33

Playback Zoom Function................................................... 34

Playback Digital Effect Functions...................................... 34

Playing Back on Your TV .................................................. 36

Audio Dubbing................................................................... 36

Special Features

Using a Memory Card........................................................37

Recording on the Memory Card.........................................37

Playing Back Files from the Memory Card ........................40

Copying Pictures from a Memory Card to a Cassette .......41

Slide Show.........................................................................42

Creating a Title ..................................................................43

Inserting a Title ..................................................................43

Protecting the Files on a Memory Card from Accidental

Erasure (File Lock)......................................................... 44

Deleting the Files recorded on a Memory Card ................. 44

Formatting a Memory Card................................................45

DPOF Setting.....................................................................45

Copying your DV Cassette to an S-VHS or

VHS Cassette (Dubbing)................................................46

Copying an S-VHS or VHS Cassette to

your DV Cassette...........................................................46

Using your Palmcorder with Digital Video Equipment

(Dubbing) .......................................................................47

Using the Software with a Computer .................................48

ArcSoft Software................................................................49

Using the Supplied USB Connection Kit............................ 50

Installing USB Driver..........................................................50

Connecting Computer and Palmcorder ............................. 50

Using the G726 Decoder ...................................................51

Installing the G726 Decoder ..............................................51

Check if Palmcorder is correctly recognized...................... 52

To disconnect USB cable safely ........................................52

Verifying and updating driver .............................................53

If you no longer need software or driver (uninstall)............56

Notes .................................................................................57

Others

Indications..........................................................................58

Warning/Alarm Indications.................................................60

Notes & Precautions..........................................................61

Cautions for Use................................................................67

Explanation of Terms.........................................................70

Specifications.....................................................................71

Palmcorder Accessory System..........................................72

Palmcorder Accessory Order Form

(For USA Customers) ....................................................73

Before Requesting Service (Problems and Solutions)....... 74

Request for Service Notice ................................................76

Limited Warrant (For USA Customers)..............................77

Customer Services Directory .............................................78

Warranty (For Canadian Customers).................................79

Index ..................................................................................80

Spanish Quick Use Guide/

Guía española para el uso rápido..................................81

Before Using

PV-DAC11 (For USA) PV-DAC11-K (For Canada)

CGR-D14

CR2025

N2QAEC000003 N2QCAD000001

5) 6)

VFC3861

VYP8616

K2KC4CB00002

VFC3506

Standard Accessories

Illustrated on the left are accessories packaged with the Palmcorder.

1) AC Adaptor, DC Cable and AC Cable (l 12)

≥Supplies power to the Palmcorder.

CAUTION:

This unit will operate on 110/120/220/240 V AC. An AC plug adaptor may be required for voltages other than 120 V AC. Please contact either a local or foreign electrical parts distributor for assistance in selecting an alternate AC plug. We recommend using the accessory power plug adaptor (VJSS0070) in an area which has special AC outlets.

2) Battery Pack (l 12)

≥Supplies power to the Palmcorder.

3) Remote Controller and Button-Type Battery (l 10, 11)

4) Tethered Remote Control

5) Lens Cap and Lens Cap String (l 13)

6) Lens Hood for Card Mode Recording (l 37, 64, 69)

≥By attaching supplied Lens Hood in Card Mode you can block direct

sunlight when recording images. However, the Lens Cap cannot be attached when the lens hood is being used.

7) A/V Cable (l 36)

8) Shoulder Strap (l 14)

9) SD Memory Card (l 57)

10) CD-ROM:

USB Driver for Panasonic DVC (l 50) G726 Decoder (l 51) ArcSoft Software (l 48, 49)

Microsoft United States and other countries. ≥Macintosh is a registered trademark of Apple Computer, Inc. 2001. ArcSoft,

the ArcSoft logo, ArcSoft PhotoImpression 3.0, ArcSoft PhotoBase 3.0, ArcSoft PanoramaMaker 3.0 and ArcSoft PhotoPrinter 2000 Pro are trademarks of ArcSoft, Inc.

≥All product/brand names are trademarks or registered trademarks of the

respective holders.

≥Intel ≥i.LINK and “¥” are trademarks. ≥IBM is a registered trademark of IBM Company. ≥MultiMediaCard is a trademark. ≥SD is a trademark.

11) USB Cable (l 50)

and Windows® are registered trademarks of Microsoft in the

Pentium® is a registered trademark.

10) 11)

LSFT0489 VFA0366

RP-SD016BVE0

Quick Guide

Charge the Battery.

(l 12)

≥Connect the AC Cable to the AC Adaptor and plug it into the AC Wall

Outlet.

≥Attach the Battery to the AC Adaptor. (This will start the charging

process.)

≥The [POWER] Lamp and [CHARGE] Lamp light up, and charging starts. ≥When the [CHARGE] Lamp goes off, charging is completed.

≥Since the Battery will not be charged when the DC Cable is connected

to the AC Adaptor, disconnect it.

Attach the Charged Battery to the Palmcorder.

Insert the Cassette.

≥Slide the [OPEN/EJECT]

(l 14)

Lever toward the front and pull down to

(l 12)

open the Cassette Compartment.

OPEN/ EJECT

≥Insert the Cassette. ≥Press the [PUSH CLOSE]

to load the Cassette.

≥Close the outside compartment Cover.

PUSH

CAMERA VCR CARD

P.B.

5, 6

BACKLIGHT

FADE

MAGICPIX

TITLE

TELE JUMP

CAMERA VCR CARD

P.B.

CAMERA STILL

MULTI/ P-IN-P

Start recording.

≥Turn the Palmcorder on. (l 15) ≥Rotate the Switch ≥Press the ≥Press the

(l 21)

to [ON]. (The [CAMERA] Lamp lights up.)

Button. (Recording starts.)

Button again to pause the recording.

To View the Playback Picture

Switch to the VCR Mode, rewind the tape, and play the tape

(l 31)

back.

≥Set the ≥Press the ≥Press the ≥Press the

Turn the Palmcorder off.

≥Set the 9 Switch to [OFF].

Switch to VCR mode. (The [VCR] Lamp lights up.)

Button. (Rewind the tape.)

Button. (Playback starts.)

Button. (Playback stops.)

(l 15

)

17)

18)

19)

20)

21)

22)

23)

Controls and Components

13) 14) 16)15)

8)7)

BACKLIGHT

FADE

6)5)

CAMERA STILL

MAGICPIX

10) 12)11)

MULTI/

25)

26)

TITLE

P-IN-P

27)

TELE JUMP

24)

28)

QUICK

29)

30)

31)

33)

CAMERA VCR CARD

P.B .

START

32)

1) LCD Monitor (l 15, 69)

................................................................................................................................

......................................................................................................................................................................

................................................................................................................................................................................................................................................................

......................................

............................................................................

≥Due to limitations in LCD production technology, there may be some

tiny bright or dark spots on the LCD Monitor screen. However, this is not a malfunction and does not affect the recorded picture.

......................................................................................................................................................................

2) LCD Monitor Open Tab [OPEN 4] (l 15)

3) Accessory Shoe

≥Accessories, such as a stereo microphone (not supplied), are attached

here.

4) Rewind/Review Button [6] (l 31) Reverse Search Button [SEARCHs] (l 21) Recording Check Button [S] (l 21)

5) Play Button [1] (l 31, 40, 42) Backlight Button [BACKLIGHT] (l 24)

(l 31)

6) Fast Forward/Cue Button [5] Forward Search Button [SEARCHr] (l 21)

7) MAGICPIX Button [MAGICPIX] (l 24)

8) Stop Button [∫] (l 31, 40, 42) Fade Button [FADE] (l 23)

9) Still Button [;] (l 32, 40, 42) Camera Still Button [CAMERA STILL] (l 22)

10) 1.5 Times Tele Jump Zoom Button [TELE JUMP] (l 22)

11) Title Button [TITLE] (l 43)

12) Multi-Picture Button [MULTI] (l 30, 43) Picture-in-Picture Button [P-IN-P] (l 30)

13) Tape/Card PhotoShot Selector [TAPE/CARD/CARD MODE] (l 21, 37)

14) Card Access Lamp [ACCESS] (l 37)

15) Card Slot Cover (l 37)

16) Card Slot (l 37)

17) Viewfinder (l 15, 69)

.........................................................................................................................

≥Due to limitations in LCD production technology, there may be some

tiny bright or dark spots on the Viewfinder screen. However, this is not a malfunction and does not affect the recorded picture.

.........................................................................................................................

18) Eyepiece Corrector Knob (l 15)

19) Battery Eject Button [PUSH BATT] (l 12)

20) Menu Button [MENU] (l 16)

21) Mode Selector Switch [AUTO/MANUAL/FOCUS] (l 21, 25, 26, 27)

22) Battery Holder (l 12)

23) Shoulder Strap Holders (l 14)

24) Viewfinder Pull Knob (l 15)

25) Multi-Function Dial [PUSH] (l 16, 20, 26, 27, 31, 32)

26) PhotoShot Button [PHOTO SHOT] (l 22, 37, 38)

27) Zoom Lever [W/T] (l 22, 23)

28) Grip Belt (l 13)

29) Quick Start Lamp (l 25)

30) Quick Start Button [QUICK START] (l 25)

31) Recording Start/Stop Button (l 21, 29, 30)

32) Off/On Mode Selector Switch [OFF/ON/MODE] (l 15, 21, 31)

33) Operation Mode Lamps [CAMERA/VCR/CARD P.B.] (l 16, 21, 31, 40)

34) Tripod Receptacle

≥Use for mounting the Palmcorder on an optional tripod.

34)

35)

36)

TO PC

37)

38)

MIC

A/V IN/OUT PHONES/ REMOTE

47) 48) 49)

DIGITAL STILL PICTURE

S-VIDEO IN/OUT

53)

39)

40)

41)

42)

43)

44)

45)

46)

54)

35) Reset Button [RESET] (l 74)

36) Speaker

37) Cassette Compartment Cover (l 14)

38) Cassette Cover Close Button [PUSH CLOSE] (l 14)

39) Cassette Holder

40) Cassette Eject Lever [OPEN/EJECT] (l 14)

41) Lens Hood (l 69)

42) Lens (LEICA DICOMAR)

≥LEICA is a registered trademark of Leica microsystems IR GmbH and

DICOMAR is a registered trademark of Leica Camera AG.

43) Free Angle Flash (l 28)

44) Microphone (Built-in, stereo) (l 22)

45) White Balance Sensor (l 27, 70) Remote Control Sensor (l 11)

46) Tally Lamp (l 21)

47) Microphone Jack [MIC] (l 22, 64)

≥Connecting with an external microphone or audio equipment. (When

this Jack is in use, the built-in microphone does not operate.)

48) Audio-Video Input/Output Jack [A/V IN/OUT] (l 36) Headphone Jack [PHONES] (l 63) Tethered Remote Control Jack [REMOTE] (l 10)

≥Connecting an AV Cable or Tethered Remote Control to this Jack

activates the Palmcorder’s built-in speaker, but connecting a headphone, etc. deactivates it.

≥When plugging the pin plug of the AV cable into the AV output terminal,

plug it in as far as it goes.

49) S-Video Input/Output Jack [S-VIDEO IN/OUT] (l 36)

50) USB Jack [TO PC] (l 50)

51) Digital Still Picture Terminal [DIGITAL STILL PICTURE]

52) DV Input/Output Terminal (i.LINK) [¥] (l 47)

≥Connect this to the digital video equipment. ≥“i.LINK” is the name of connectors in accordance with IEEE1394-1995.

“¥” is a logo marked on products conforming with the “i.LINK” specifications.

53) Lens Cap String Holder (l 13)

54) Flash Sensor (l 28)

50) 51) 52)

11)

12)

13)

14)

15)

Remote Controller

Using the wireless Remote Controller that is supplied with the Palmcorder,

DATE/

OSD

TIME

COUNTER

RESET

MULTI/

¥REC

P-IN-P

PLAY

/REW

61 5

STILL ADV

PAUSE

;

STOP

INDEX INDEX

∫

SELECT

VAR.

STORE

OFF/ON

P.B.DIGITAL

DATE/

OSD

TIME

COUNTER

RESET

MULTI/

¥REC

P-IN-P

PLAY

/REW

61 5

STILL ADV

PAUSE

;

STOP

INDEX INDEX

∫

SELECT

VAR.

STORE

OFF/ON

P.B.DIGITAL

PHOTO

SHOT

TITLE

A.DUB

FF/

STILL ADV

PHOTO

SHOT

TITLE

A.DUB

FF/

STILL ADV

START/

STOP

ZOOM

sVOL r

P.B.

ZOOM

SET

ITEM

START/

STOP

ZOOM

sVOL r

P.B.

ZOOM

SET

ITEM

most of the Palmcorder functions can be operated from a distance.

Remote Controller Buttons

1) Date and Time Button [DATE/TIME] (l 60)

2) Indication Output Button [OSD] (l 36)

3) Counter Reset Button [RESET] (l 70)

4) Indication Shift Button [COUNTER] (l 60)

5) Multi-Picture/Picture-in-Picture Button [MULTI/P-IN-P] (l 30, 41)

6) Recording Button [REC] (l 47)

7) Audio Dubbing Button [A.DUB] (l 36)

8) Upward Direction Button [π] (for Playback Zoom Function) (l 34)

9) Left/Right Direction Button [∑, ∏] (for Playback Zoom Function)

(l 34)

10) Downward Direction Button [∫] (for Playback Zoom Function) (l 34)

10)

11) Slow Motion/Still Advance Button [E, D] (E : reverse direction, D: normal direction) (l 32)

12) Index Search Button [:, 9] (:: reverse direction, 9: normal direction) (l 33)

13) Selection Button [SELECT] (l 34)

14) Store Button [STORE] (l 34)

15) Off/On Button [OFF/ON] (l 34)

16) Zoom/Volume Button [ZOOM/VOL] (l 22, 23, 31, 34)

17) Variable Speed Search Button [VAR.SEARCH] (l 31)

18) Playback Zoom Button [P.B. ZOOM] (l 34)

19) Speed Selection Button [π, ∫] (for Variable Speed Search Function) (l 31)

16)

The following buttons function in the same manner as the corresponding buttons on the Palmcorder.

20) PhotoShot Button [PHOTO SHOT] (l 22, 37)

21) Recording Start/Stop Button [START/STOP] (l 21)

22) Title Button [TITLE] (l 43)

23) Menu Button [MENU] (l 16)

17)

24) Item Set Button [SET] (l 16)

18)

25) Item Select Button [ITEM] (l 16)

19)

26) Fast-forward/Cue Button [5] (l 31)

27) Play Button [1] (l 31, 40)

28) Rewind/Review Button [6] (l 31)

29) Pause Button [;] (l 32, 40)

30) Stop Button [∫] (l 31, 40)

26)

27)

28)

29)

30)

OSD

COUNTER

MULTI/ P-IN-P

/REW

61 5

STILL ADV

INDEX INDEX

SELECT

STORE

OFF/ON

P.B.DIGITAL

TIME

RESET

¥REC

PLAY

PAUSE

;

STOP

∫

VAR.

SHOT

TITLE

A.DUB

FF/

STILL ADV

sVOL r

ITEM

START/

PHOTO

DATE/

STOP

ZOOM

P.B.

ZOOM

SET

ª Tethered Remote Control

This controller allows the scene to be shot in various angles, high to low and is also convenient when a Tripod is used. When you do not use this

20)

controller, attach the clip to the Grip Belt for convenience. This controller allows the camera to be used more conveniently by a

21)

left-handed user.

22)

≥When using the Tethered Remote control, plug it in as far as it goes.

Recording Start/Stop Button [REC]

Zoom Lever [W/T]

PhotoShot Button [PHOTO SHOT]

23)

24)

25)

2 3

ª Inserting the Button-type Battery

Before using the remote controller, insert the supplied button-type battery.

While pressing the Stopper 1, pull out the Battery Holder.

Insert the button-type battery with the imprint (i) facing

upward. Insert the Battery Holder into the Remote Controller.

≥When the button-type battery becomes weak, replace it with a new CR2025

battery. (A battery is normally expected to last about one year. However, it depends on operation frequency.)

≥Be sure to match the poles properly when inserting the battery.

................................................................................................................................

......................................................................................................................................................................

......................................

............................................................................

Warning

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions. Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212°F (100°C) or incinerate. Keep the Button-Type battery out of the reach of children. Never put Button-Type battery in mouth. If swallowed, call your doctor.

................................................................................................................................

......................................................................................................................................................................

Replace battery with Panasonic PART NO. VSBW0004 (CR2025) only. Use of another battery may present a risk of fire or explosion. Caution: Battery may explode if mistreated. Dispose of used battery promptly. Keep away from children. Do not recharge, disassemble or dispose of in fire.

......................................

............................................................................

ª Using the Remote Controller 1

Direct the Remote Controller at the Remote Control Sensor on the Palmcorder and press the desired button.

≥Distance from the Palmcorder: Within approximately 15 feet (5 meters) ≥Angle: Approximately 15 degrees in the vertical and horizontal

directions from the central axis

15˚

START/

PHOTO

15˚

DATE/

OSD

TIME

RESET

COUNTER

MULTI/

¥REC

P-IN-P

PLAY

/REW

615

STILL ADV

PAUSE

INDEX INDEX

STOP

SELECT

STORE

OFF/ON

P.B.DIGITAL

STOP

SHOT

TITLE

ZOOM

A.DUB

sVOLr

FF/

STILL ADV

;

∫

VAR.

ITEM

P.B.

ZOOM

SET

≥The above operating ranges are for indoor use. Outdoors, or under strong

light, the equipment may not operate properly even within the above ranges.

≥Within 3 feet (1 meter) range, you can also use the Remote Controller on

the side (the LCD Monitor side) of the Palmcorder.

Selecting Remote Controller Modes

When two Palmcorders are used simultaneously, they can be operated individually by selecting different Remote Controller Modes. ≥If the Remote Controller Mode on the Palmcorder and Remote Controller do

not match, [REMOTE] is displayed.

Setting on the Palmcorder:

Set [REMOTE] on the [OTHER FUNCTIONS] Sub-Menu to the desired Remote Controller Mode.

Setting on the Remote Controller:

[VCR1]: Press the [D] Button and [∫] Button simultaneously. [VCR2]: Press the [E] Button and [∫] Button simultaneously. ≥When the battery in the Remote Controller is replaced, the Mode is

automatically reset to [VCR1] Mode.

1 2

Power Supply

ª Using the AC Adaptor

Insert the battery-shaped connector of the DC Cable into the

Battery Holder on the Palmcorder. Connect the DC Cable to the [DC OUT] Jack on the AC

Adaptor. Connect the AC Adaptor and AC Cable.

≥The AC Cable’s outlet plug cannot be pushed fully into the AC Adaptor

Jack. A gap will remain as shown

≥Before connecting or disconnecting the power supply, set the [OFF/

ON/MODE] Switch on the Palmcorder to [OFF] and make sure that neither [CAMERA/VCR/CARD P.B.] Lamps or Quick Start Recording Lamp is lit.

≥Battery cannot be charged if DC Cable is connected to AC Adapter.

PUSH BAT T

ª Using the Battery

Before use, fully charge the battery.

Attach the Battery to AC Adaptor and charge it.

≥Since the Battery will not be charged when the DC Cable is connected

to the AC Adaptor, disconnect it.

≥The [POWER] Lamp and [CHARGE] Lamp lights up, and charging

starts.

≥When the [CHARGE] Lamp goes off, charging is completed.

Attach the charged Battery to the Palmcorder.

Disconnecting the Power Source

Set the [OFF/ON/MODE] Switch 1 to [OFF], and while pressing the [PUSH BATT] Button disconnect it.

≥When attaching or removing battery, set [OFF/ON/MODE] Switch to

[OFF] and make sure the Operation Mode Lamp is not lit.

, slide the Battery or DC Input Lead upward to

≥For other notes, see page 61.

~~~~~~~~~~~~~~~~~~~~~~~~

CGR-D08A/1B

CGR-D14

CGR-D16A/1B

CGP-D28A/1B

CGR-D53A/1K

1 h.

1 h 35 min. (1 h 15 min.)

1 h 30 min.

2 h 10 min. (1 h 45 min.)

2 h.

3 h 10 min. (2 h 30 min.)

3 h 15 min.

5 h 25 min. (4 h 25 min.)

5 h 20 min.

10 h 10 min. (8 h 15 min.)

Charging Time and Available Recording Time

Charging Time

Maximum Continuous Recording Time

≥“1 h 20 min.” indicates 1 hour and 20 minutes. ≥Battery CGR-D14 is supplied. ≥The hours shown in the table are approximate hours. The numeric

characters in parentheses indicate the recording time when the LCD monitor is used. In actual use, the available recording time may be shorter in some cases.

≥The hours shown in the table are for continuous recording at a temperature

of 68xF (20xC) and humidity of 60%. If the Battery is charged at a higher or lower temperature, the charging time may be longer.

ª Attach the Lens Cap

To protect the Lens surface, attach the Lens Cap.

Detach the Grip Belt from the Grip Belt Holder.

Pass the end of the Lens Cap String through the Lens Cap

String holder. Pass the other end of the String through the loop made by

the String itself and pull it toward the direction indicated by an arrow. Fit the lens cap onto the lens cap string.

≥The removed Lens Cap can be hooked onto the Grip Belt 1. (When you

are not recording, be sure to keep the Lens Cap attached to the Lens for protection.)

≥Lens Cap cannot be attached when the supplied Lens Hood for Card Mode

Picture Recording is being used.

ª Adjust the Grip Belt

Lens Cap and Grip Belt

Adjust the length of the Grip Belt to the size of your hand.

Detach the tip of the Grip Belt and adjust the length of it.

1111

Reattach the tip of the Grip Belt.

2222

ª To Use as a Free Style Grip Belt

Using the Grip Belt as the Free Style Grip Belt makes it easier to handle and carry the Palmcorder. Remote control.

Detach the tip of the Grip Belt from the Grip Belt Holder and

adjust the length of it. Attach the Grip Belt around your wrist.

It is also more convenient to use with the Tethered

Attaching the Shoulder Strap

We recommend that you attach the Shoulder Strap before going outdoors to record so as to avoid dropping the Palmcorder.

Pass the tip of the Shoulder Strap through the Shoulder

Strap Holders on the Palmcorder and pull the Shoulder Strap. Fold the tips of the Shoulder Strap, pass it through the

Shoulder Strap Length Adjuster, and pull it.

≥Pull it out more than 1 inch (2 cm) 1 from the Shoulder Strap Length

Adjuster so that it cannot slip off.

≥Please perform this step on the other side as well.

~~~~~~~~~~~~~~~~~~~~~~~~

Inserting a Cassette

OPEN/ EJECT

PUSH

R E C

SAVE

When power is supplied to the Palmcorder, the cassette can be taken out without turning the Palmcorder on.

Slide the [OPEN/EJECT] Lever toward the front and pull

down to open the Cassette Compartment Cover. Insert a Cassette.

Close the Cassette Holder by pressing the [PUSH CLOSE]

Button. Close the Cassette Compartment Cover.

≥For other notes, see page 61.

ª Accidental Erasure Prevention

Opening the accidental erasure prevention slider 1 on the cassette (by sliding it in the [SAVE] arrow direction) prevents recording. To enable recording, close the accidental erasure protection slider (by sliding it in the [REC] arrow direction.)

Turning on/off the Palmcorder and Selecting Modes

CAMERA VCR CARD

P.B.

1, 2

Turn on the power first and then select Modes.

ª How to Turn on the Power 1

Set the [OFF/ON/MODE] Switch to [ON] while pressing the center Button

≥The [CAMERA] Lamp lights up.

ª How to Switch Modes 2

Rotate the [OFF/ON/MODE] Switch.

≥With each slide of the Switch, the Mode switches in the order of Camera

Mode, VCR Mode, and Card Playback Mode.

≥The appropriate Mode Lamp lights up.

ª How to Turn off the Power

Set the [OFF/ON/MODE] Switch to [OFF] while pressing the

center Button

~~~~~~~~~~~~~~~~~~~~~~~~~

Using the Viewfinder

Before using the Viewfinder, adjust the field of view so that the displays inside the Viewfinder become clear and easy to read.

Hold the Viewfinder Pull knob 1, pull out the Viewfinder and

tilt it up. Adjust the Viewfinder by sliding the Eyepiece Corrector

Knob

180x 90x

LCD/EVF SET

LCD BRIGHTNESS

LOW||||----HIGH

LCD COLOR LEVEL LOW||||----HIGH

EVF BRIGHTNESS LOW||||----HIGH

PUSH MENU TO RETURN

Using the LCD Monitor

With the LCD Monitor open, you can also record the picture while watching it.

Set the [OFF/ON/MODE] Switch to [ON].

1111

Put your finger on the [OPEN 4] Tab 3 and pull the LCD

2222

Monitor out about 90x in the direction of the arrow.

≥The Viewfinder goes off.

Adjust the LCD Monitor angle according to the desired

3333

recording angle.

≥The LCD Monitor can rotate a maximum of 180x 4 from the vertical

position to the upward direction and a maximum of 90x downward direction. Forcefully rotating the LCD monitor beyond these ranges will damage the Palmcorder.

Closing the LCD monitor

Push the LCD Monitor until it is securely locked.

to the

ª Adjusting Brightness and Color Level

When [LCD/EVF SET] on the [DISPLAY SETUP] Sub-menu is set to [YES], the following items are displayed:

LCD Brightness [LCD BRIGHTNESS]

Adjusts the brightness of the image on the LCD screen.

LCD Color Level [LCD COLOR LEVEL]

Adjusts the color saturation of the image on the LCD screen.

Brightness of the Viewfinder [EVF BRIGHTNESS]

Adjust the brightness of the image in the Viewfinder.

Press the [PUSH] Dial and select the item you want to adjust.

Rotate the [PUSH] Dial and increase or decrease the number

of the vertical bars on the Bar Indication.

≥The Bar Indication has 8 steps. A larger number of vertical bars

indicates stronger brightness or color saturation.

Increasing the Brightness of the Entire LCD Monitor

Set the [LCD MODE] on the [DISPLAY SETUP] Sub-Menu to [BRIGHT].

≥These adjustments do not affect the recorded images.

≥For other notes, see page 69.

2 3

CAMERA VCR CARD

P.B.

CAMERA FUNCTIONS

CAMERA SETUP

DIGITAL EFFECT

CARD SETUP

MULTI-PICTURES

RECORDING SETUP

DISPLAY SETUP

OTHER FUNCTIONS

PUSH MENU TO EXIT

PLAYBACK FUNCTIONS

DIGITAL EFFECT

CARD SETUP

MULTI-PICTURES

RECORDING SETUP

AV IN/OUT SETUP

DISPLAY SETUP

OTHER FUNCTIONS

PUSH MENU TO EXIT

DELETE CARD FILE

CARD EDITING

DISPLAY SETUP

OTHER FUNCTIONS

2, 3, 4, 5

1, 2

W.B./SHUTTER/IRIS/

MF/VOL/JOG

VCR FUNCTIONS

CARD FUNCTIONS

PUSH

Using the Menu Screen

To facilitate the selection of a desired function or setting, this Palmcorder displays various function settings on menus.

Press the [MENU] Button.

≥The Menu corresponding to the Mode selected by using the [OFF/ON/

MODE] Switch

≥When the [CAMERA] Lamp is on, the Camera Function Menu is

displayed.

≥When the [VCR] Lamp is on, the VCR Function Menu is displayed. ≥When the [CARD P.B.] Lamp is on, the Card Function Menu is

displayed.

Rotate the [PUSH] Dial to select a desired Sub-Menu.

Press the [PUSH] Dial to display the selected Sub-Menu.

Rotate the [PUSH] Dial to select the item to be set.

Press the [PUSH] Dial to set the selected item to a desired

Mode.

≥With each press of the [PUSH] Dial, the cursor [1] brings up a

subsequent Mode. Menu items that cannot be used in combination with the selected menu items are displayed in dark blue.

≥While a Menu is displayed, you cannot begin to record or play back. Menus

can be displayed during playback but not during recording.

≥The above operations can be carried out using the Remote Controller.

(l 10)

≥To display the Menu, press the [MENU] Button

Controller.

≥To select items on the Menu, press the [ITEM] Button

Remote Controller.

≥To set the mode for the selected items, press the [SET] Button

on the Remote Controller.

To Exit the Menu Screen

Press the [MENU] Button again.

About the Menu Mode Setting

The setting selected on the Menu will be retained even when the Palmcorder is turned off. However, if the Battery or AC Adaptor is disconnected before turning the Palmcorder off, the selected setting may not be retained. (But, the setup of [EFFECT2] (l 29) is not retained.) ≥Menu operation flow is shown in this text by >>.

is displayed.

on the Remote

on the

PUSH MENU TO EXIT

START/

PHOTO

DATE/

TIME

RESET

¥REC

PLAY

PAUSE

;

STOP

∫

VAR.

PICTURE

STOP

SHOT

TITLE

ZOOM

A.DUB

sVOLr

FF/

STILL ADV

P.B .

ZOOM

SET

ITEM

No.25 100-0012

OSD

COUNTER

MULTI/

P-IN-P

/REW

615

STILL ADV

INDEX INDEX

SELECT

STORE

OFF/ON

P.B.DIGITAL

5 7 6

ª File Selection in the Card Playback Mode

A File Selection Operation may be necessary during Menu Operations. In this case, carry out the following procedure.

Turn the [PUSH] Dial and select a file.

1111

≥The selected file is marked by a frame 8.

Press the [PUSH] Dial to confirm the selection of the file.

2222

≥After the above File Selection Procedure, carry out the various Menu

Operations. (The above procedure will not be repeated in the following instructions.)

EFFECT1

EFFECT2 OFF NEGA SEPIA

RETURN ---- YES

PICTURE SIZE PICTURE QUALITY

10)

FINE NORMAL ECONOMY MPEG4 MODE

11)

CREATE TITLE

12)

RETURN ---- YES

13)

SCAN MODE

14)

SPEED FAST NORMAL SLOW SWING OFF ON

15)

P-IN-P 1 2 3 4

16)

RETURN ---- YES

17)

18)

19)

20)

21)

22)

23)

24)

25)

26)

27)

28)

29)

30)

31)

32)

REMOTE TALLY LED OFF ON

33)

BEEP OFF ON

34)

SHUTTER OFF ON CLOCK-SET

35)

SELF-REC NORMAL MIRROR VOICE POWER SAVE OFF ON

36)

37)

RETURN ---- YES

CAMERA SETUP

PROG.AE OFF 5 7

PROGRESSIVE AUTO ON OFF EIS D.ZOOM CINEMA OFF ON

RETURN

RETURN ---- YES

REC-SPEED AUDIO-REC 12bit INDEX 2HOUR DAY WIND-CUT OFF ON ZOOM MIC FLASH

RED EYE REDUCTION FLASH LEVEL

RETURN ---- YES

DATE/TIME C.DISPLAY LINEAR MEMORY

C.RESET ---- YES DISPLAY ALL PARTIAL OFF LCD MODE NORMAL BRIGHT LCD/EVF SET ---- YES

RETURN ---- YES

4 Ω º

OFF ON OFF 25 700

PUSH MENU TO EXIT

DIGITAL EFFECT

OFF MULTI P-IN-P WIPE MIX STROBE GAIN-UP TRAIL MOSAIC MIRROR

MONO SOLARI

PUSH MENU TO EXIT

CARD SETUP

1280 960 640 480

FINE NORMAL

PUSH MENU TO EXIT

MULTI-PICTURES

STROBE MANUAL

PUSH MENU TO EXIT

RECORDING SETUP

SP LP

OFF ON

ON AUTO

s NORMAL r

PUSH MENU TO EXIT

DISPLAY SETUP

OFF D/T DATE

T.CODE

PUSH MENU TO EXIT

OTHER FUNCTIONS

VCR1 VCR2 OFF

---- YES

PUSH MENU TO EXIT

---- YES

16bit

OFF ON

List of Menus

The illustrations of the Menus are for explanation purposes only, and they are different from the actual Menus.

Camera Mode Main-Menu [CAMERA FUNCTIONS]

[CAMERA SETUP] Sub-Menu

1) Auto Exposure Mode [PROG.AE] (l 25)

2) Progressive PhotoShot Mode [PROGRESSIVE] (l 22)

3) Digital Effect Image Stabilizer [EIS] (l 23)

4) Digital Zoom [D.ZOOM] (l 23)

5) Cinema-like Format Recording [CINEMA] (l 24)

6) Returning to the Main-Menu [RETURN]

[DIGITAL EFFECT] Sub-Menu

7) Digital Effects 1 [EFFECT1] (l 29)

8) Digital Effects 2 [EFFECT2] (l 29)

[CARD SETUP] Sub-Menu

9) Picture Size [PICTURE SIZE] (l 37)

10) Picture Quality [PICTURE QUALITY] (l 38)

11) MPEG4 Picture Quality [MPEG4 MODE] (l 39)

12) Title Creation [CREATE TITLE] (l 43)

[MULTI-PICTURES] Sub-Menu

13) Multi-Picture Mode [SCAN MODE] (l 30)

14) Strobe Multi-Picture Speed [SPEED] (l 30)

15) Swing Mode [SWING] (l 30)

16) Position of Small Picture inside Normal Picture [P-IN-P] (l 30)

[RECORDING SETUP] Sub-Menu

17) Recording Speed Mode [REC-SPEED] (l 20)

18) Audio Recording Mode [AUDIO-REC] (l 20, 36)

19) Index Mode [INDEX] (l 33)

20) Wind Noise Reduction [WIND-CUT] (l 25)

≥If this function is set to [ON], the sound of wind hitting the microphone

can be reduced for recording.

21) Zoom Microphone [ZOOM MIC] (l 22)

22) Flash [FLASH] (l 28)

23) Red Eye Reduction [RED EYE REDUCTION] (l 28)

24) Flash Level [FLASH LEVEL] (l 28)

[DISPLAY SETUP] Sub-Menu

25) Date and Time Indication [DATE/TIME] (l 60)

26) Counter Display Mode [C.DISPLAY] (l 60)

27) Counter Reset [C.RESET] (l 70)

≥Set the counter value to zero. However, it cannot reset the Time Code.

28) Display Mode [DISPLAY] (l 60)

29) LCD Brightness [LCD MODE] (l 15)

30) LCD and Viewfinder Adjustment [LCD/EVF SET] (l 15)

[OTHER FUNCTIONS] Sub-Menu

31) Remote Controller Mode [REMOTE] (l 11)

32) Recording Lamp [TALLY LED] (l 21)

33) Beep Sound [BEEP] (l 61)

34) Shutter Effect [SHUTTER] (l 22)

35) Date and Time Setting [CLOCK-SET] (l 20)

36) Self-Recording [SELF-REC] (l 21)

37) Voice Power Save [VOICE POWER SAVE] (l 65)

PLAYBACK FUNCTIONS

BLANK SEARCH ---- YES RECORD TO CARD ---- YES INDEX PHOTO SCENE AUDIO ST1 ST2 MIX AUDIO OUT STEREO L R

RETURN ---- YES

10)

11)

12)

13)

14)

15)

16)

17)

18)

19)

PUSH MENU TO EXIT

DIGITAL EFFECT

EFFECT OFF ON EFFECT SELECT OFF MULTI WIPE MIX STROBE NEGA SEPIA MONO TRAIL SOLARI MOSAIC MIRROR

RETURN ---- YES

PUSH MENU TO EXIT

PICTURE QUALITY FINE NORMAL ECONOMY MPEG4 MODE

CREATE TITLE

RETURN ---- YES

SCAN MODE SPEED FAST NORMAL SLOW SWING OFF ON

RETURN ---- YES

CARD SETUP

FINE NORMAL

PUSH MENU TO EXIT

MULTI-PICTURES

STROBE MANUAL

PUSH MENU TO EXIT

RECORDING SETUP

REC-SPEED SP LP AUDIO-REC 12bit

RETURN ---- YES

PUSH MENU TO EXIT

AV IN/OUT SETUP

AV JACK

A.DUB INPUT DV OUT

IN/OUT OUT/PHONES

OFF ON

---- YES

16bit

MIC AV IN

VCR Mode Main-Menu [VCR FUNCTIONS]

[PLAYBACK FUNCTIONS] Sub-Menu

1) Blank Search [BLANK SEARCH] (l 32)

2) Recording to Card [RECORD TO CARD] (l 38)

3) Index Search Mode [INDEX] (l 33)

4) Audio Selector [AUDIO] (l 36)

5) Audio Output Mode [AUDIO OUT] (l 64)

6) Returning to the Main-Menu [RETURN]

[DIGITAL EFFECT] Sub-Menu

7) Digital Effect On/Off [EFFECT] (l 34)

8) Digital Effect Selection [EFFECT SELECT] (l 34)

[CARD SETUP] Sub-Menu

9) Picture Quality [PICTURE QUALITY] (l 38)

10) MPEG4 Picture Quality [MPEG4 MODE] (l 40)

11) Title Creation [CREATE TITLE] (l 43)

[MULTI-PICTURES] Sub-Menu

12) Multi-Picture Mode [SCAN MODE] (l 35)

13) Strobe Multi-Picture Speed [SPEED] (l 30, 35)

14) Swing Mode [SWING] (l 35)

[RECORDING SETUP] Sub-Menu

15) Recording Speed Mode [REC-SPEED] (l 20)

16) Audio Recording Mode [AUDIO-REC] (l 20, 36)

[AV IN/OUT SETUP] Sub-Menu

17) AV Jack [AV JACK] (l 36, 46, 63)

18) Audio Dubbing Input [A.DUB INPUT] (l 36)

19) AD Conversion Output [DV OUT] (l 47)

[DISPLAY SETUP] Sub-Menu

20) Camera Data [REC DATA]

≥If you set [REC DATA] to [ON], the settings (shutter speed (l 26), iris

(l 26) and white balance settings (l 27), etc.) used during the

recordings are displayed during playback. [---] appears on the display when there is no data.

≥The settings information may not displayed properly if the camera data

of this Palmcorder are played back on other equipment.

The camera data will not be recorded in the following cases:

≥When the data are recorded from a card to a tape. ≥When recording proceeds with no input signals supplied. ≥When recording involves the use of the S-Video or AV Input Jack. ≥When pictures with no camera data are recorded using the DV

Terminal.

≥When displaying a list of titles.

All of the other items on the [DISPLAY SETUP] Sub-Menu are the same as those on the [DISPLAY SETUP] Sub-Menu of the [CAMERA FUNCTIONS] Main-Menu.

[OTHER FUNCTIONS] Sub-Menu

≥Same as described on page 17.

RETURN ---- YES

PUSH MENU TO EXIT

DISPLAY SETUP

DATE/TIME OFF D/T DATE C.DISPLAY LINEAR MEMORY T.CODE C.RESET ---- YES DISPLAY ALL PARTIAL OFF REC DATA OFF ON

20)

LCD MODE NORMAL BRIGHT LCD/EVF SET ---- YES RETURN ---- YES

PUSH MENU TO EXIT

OTHER FUNCTIONS

REMOTE VCR1 VCR2 OFF CLOCK-SET ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

DELETE CARD FILE

DELETE FILE

DATE/TIME OFF D/T DATE C.DISPLAY LINEAR MEMORY T.CODE C.RESET ---- YES DISPLAY ALL PARTIAL OFF LCD MODE NORMAL BRIGHT LCD/EVF SET ---- YES

RETURN ---- YES

REMOTE VCR1 VCR2 OFF

VOICE POWER SAVE OFF ON

BY SELECTION DELETE ALL FILES DELETE TITLE

BY SELECTION

RETURN ---- YES

PUSH MENU TO EXIT

CARD EDITING

RECORD TO TAPE ---- YES FILE SEARCH ---- YES FILE LOCK ---- YES SLIDE SHOW ---- YES DPOF SETTING ---- YES CARD FORMAT ---- YES

RETURN ---- YES

PUSH MENU TO EXIT

DISPLAY SETUP

PUSH MENU TO EXIT

OTHER FUNCTIONS

CLOCK-SET ---- YES

Card Playback Mode Main-Menu [CARD FUNCTIONS]

[DELETE CARD FILE] Sub-Menu

1) Selecting and deleting a File [DELETE FILE BY SELECTION] (l 44)

2) Deleting All Files [DELETE ALL FILES] (l 44)

3) Selecting and Deleting a Title [DELETE TITLE BY SELECTION] (l 44)

[CARD EDITING] Sub-Menu

4) Recording to Cassette [RECORD TO TAPE] (l 41)

5) Searching a File [FILE SEARCH] (l 41)

6) Setting the Lock [FILE LOCK] (l 44)

7) Setting a Slide Show [SLIDE SHOW] (l 42)

8) Setting DPOF [DPOF SETTING] (l 45)

9) Formatting a Card [CARD FORMAT] (l 45)

[DISPLAY SETUP] Sub-Menu

≥Same as described on page 17.

[OTHER FUNCTIONS] Sub-Menu

≥Same as described on page 17.

RETURN ---- YES

PUSH MENU TO EXIT

10)

FILE SEARCH

11)

DELETE FILE FILE LOCK

12)

DPOF SETTING

13)

EXIT

14)

Short-Cut Menus of the Card Playback Mode

If you use the Short-Cut Menu, the Card Playback Mode Menu can be called up quickly. Press the [PUSH] Dial to display the Short-Cut Menu, and turn the [PUSH] Dial to select the desired Menu.

10) [FILE SEARCH]:

The [FILE SEARCH] Menu for finding files by number appears. (l 41)

11) [DELETE FILE]:

The [DELETE FILE] Menu for deleting the file being displayed appears. (l 44) Use this Menu after the file to be erased appears.

12) [FILE LOCK]: The [FILE LOCK] Menu to prevent the accidental erasure of files (Lock Setting) being displayed appears. (l 44) Use this Menu after the file to be locked appears.

13) [DPOF SETTING]: The [DPOF SETTING] Menu for performing the DPOF settings for the displayed picture appears. (l 45) Use this Menu after the picture whose DPOF settings are to be performed has appeared.

14) [EXIT]: For terminating the Short-Cut Menu.

CLOCK-SET

YEAR :2002

MONTH :OCT DAY :20 HOUR : 8PM MINUTE:46

PUSH MENU TO RETURN

1, 3 1, 2

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

Setting Date and Time

Press the [MENU] Button and rotate the [PUSH] Dial to select [OTHER FUNCTIONS] >> [CLOCK-SET] >> [YES].

Rotate and press the [PUSH] Dial to select [YEAR]/[MONTH]/ [DAY]/[HOUR]/[MINUTE] and set it to a desired value.

≥Year will cycle in the order shown below.

2000 ) 2001 ) ... ) 2089 ) 2000 ) ...

Press the [MENU] Button to finish setting the date and time.

≥The clock operation starts from [00] seconds. ≥The menu will disappear when the [MENU] button is pressed again.

≥It is possible that the built-in clock in the Palmcorder may become

inaccurate. Please check the time before recording. If the [0] Indication is flashing, charge the built-in lithium battery and reset the date and time.

~~~~~~~~~~~~~~~~~~~~~~~~

Internal Lithium Battery Recharge

The internal lithium battery sustains the operation of the clock. When the [0] Indication

Connect the AC Adaptor to the Palmcorder with the power turned off and then connect to the AC Jack.

≥After charging for 4 hours, the built-in lithium battery can power the

is lit, the internal lithium battery is near exhaustion.

clock for approximately 3 months.

CAMERA FUNCTIONS

CAMERA SETUP

DIGITAL EFFECT

CARD SETUP

MULTI-PICTURES

RECORDING SETUP

DISPLAY SETUP

OTHER FUNCTIONS

PUSH MENU TO EXIT

RECORDING SETUP

REC-SPEED

AUDIO-REC 12bit INDEX 2HOUR WIND-CUT OFF ZOOM MIC FLASH RED EYE REDUCTION FLASH LEVEL RETURN ---- YES

REC-SPEED

AUDIO-REC

INDEX 2HOUR WIND-CUT OFF ZOOM MIC FLASH RED EYE REDUCTION FLASH LEVEL RETURN ---- YES

SP LP

PUSH

MENU TO EXIT

RECORDING SETUP

SP 12bit

PUSH

MENU TO EXIT

NORMAL

OFF

16bit

OFF

~~~~~~~~~~~~~~~~~~~~~~~~

LP Mode

A desired recording speed can be selected with [REC-SPEED] on the [RECORDING SETUP] Sub-Menu.

If LP Mode is selected, the recording time becomes 1.5 times longer than that of SP Mode.

Although the image quality does not decrease with the LP Mode recording, mosaic-like noise patterns may appear on a playback image, or some normal functions may be restricted. ≥The contents that are recorded in LP Mode are not completely compatible

with other equipment.

≥Audio Dubbing is not possible with LP Mode. (l 36)

~~~~~~~~~~~~~~~~~~~~~~~~

Audio Recording Mode

The sound quality of the recorded sound can be selected with [AUDIO-REC] on the [RECORDING SETUP] Sub-Menu. High sound-quality recording is possible with “16bit 48kHz 2 track” Mode. With the “12bit 32kHz 4 track” Mode, the original sound can be recorded on 2 tracks in stereo, while the other 2 tracks can be used for re-recording.

MANU

AL FOCUS

RECORD

AUTO MANU

AL FOCUS

CAMERA VCR CARD

P.B.

REC

TAPE

CARD

PAUSE

3, 4

CARD MODE

CAMERA Mode

Recording

Set the [OFF/ON/MODE] Switch to [ON].

≥The [CAMERA] Lamp lights up.

Slide the [TAPE/CARD/CARD MODE] Selector towards

[TAPE]. Press the Recording Start/Stop Button.

≥Recording starts. ≥After the [RECORD] indicator is displayed, it changes to [REC]. ≥The Tally Lamp (LED Lamp) 3 lights up during recording and alerts

those being recorded that recording is in progress. The Tally Lamp does not light up if the [TALLY LED] on the [OTHER FUNCTIONS] Sub-menu is set to [OFF].

Press the Recording Start/Stop Button again to pause the

recording.

≥[PAUSE] is displayed.

≥If the Recording Pause Mode continues for more than 5 minutes, the power

is turned off automatically for tape protection and power conservation. To resume recording from this condition, turn on the power again.

≥When recording while the Mode Selector Switch is set to [AUTO]

Palmcorder automatically adjusts the focus and white balance. (In some cases, they cannot be adjusted automatically and need to be adjusted manually.) (l 26, 27)

ª To Check the Recording

By pressing the [S] Button 6 in the Recording Pause Mode, you can play back the last few seconds of the recorded scene.

is displayed. After checking, the Palmcorder resumes the Recording

≥[CHK]

Pause Mode.

ª To View the recorded scene while the Recording is

paused

The recorded scene can be viewed by holding down the [SEARCHj] Button

or [SEARCHi] Button 7 in the Recording Pause Mode.

The Camera Search function is useful for finding the starting point of a new scene to create a smooth transition from one scene to another. ≥When the [SEARCHj] Button is pressed, images are played back in the

reverse direction.

≥When the [SEARCHi] Button is pressed, images are played back in the

forward direction.

(Camera Search)

ª Self-Recording

By opening the LCD Monitor and turning it so that it faces forward (to the lens side), you can let the subject in front of the Palmcorder monitor the shot while shooting is in progress. ≥When the LCD Monitor is opened, the Viewfinder is disabled automatically.

However, when the LCD Monitor is rotated forward, the image is also shown in the Viewfinder.

≥If you prefer to have the image on the LCD Monitor to look like an image in

a mirror, set [SELF-REC] on the [OTHER FUNCTIONS] Sub-Menu to [MIRROR]. (Mirror Mode) Images are recorded normally and no left and right reversal occurs.

≥If [MIRROR] is selected, only recording Indication [¥], recording pause

Indication [¥;], Card Mode Indication [ ] and Remaining Battery Power Indication [x] are displayed

≥If a general Warning/Alarm Indication [°] appears, return the LCD Monitor

to the original position in order to check the specific content of the Warning/ Alarm Indication.

ª To Finish the Recording

Set the [OFF/ON/MODE] Switch to [OFF].

≥For other notes, see page 61.

, the

PhotoShot Recording on the DV Cassette

PHOTO SHOT

TAPE

CARD

CARD MODE

CAMERA STILL

PHOTO

With this function, you can record still pictures with sound for approximately 7 seconds each on the Cassette.

Slide the [TAPE/CARD/CARD MODE] Selector to [TAPE].

Press the [PHOTO SHOT] Button in the Recording Pause

Mode.

≥The Palmcorder records a still picture for about 7 seconds and then

switches back to the Recording Pause Mode.

≥PhotoShot Recording results in slightly inferior image quality.

ª Progressive PhotoShot

With the Progressive PhotoShotTM Mode, you can record still pictures with higher resolution than with the normal PhotoShot Function. ≥After setting [PROGRESSIVE] on the [CAMERA SETUP] Sub-menu to [ON]

or [AUTO], press the [PHOTO SHOT] Button in the Recording Pause Mode. [æ] is displayed.

≥This Function may not work with some function settings. (l 61) ≥If you select Card Mode, [PROGRESSIVE] is set to [ON].

Mode

ª Continuous PhotoShot

If the [PHOTO SHOT] Button is held down with the [SHUTTER] of the Sub-Menu [OTHER FUNCTIONS] set to [ON], the Palmcorder will record still images without interruptions every 0.7 seconds until the button is released. ≥The screen blinks and, at the same time, a shutter clicking sound is

recorded. (This function, however, is not enabled when Progressive PhotoShot is set to [ON] or [AUTO].)

ª Digital Still Picture

When the [CAMERA STILL] Button 2 is pressed, images become still pictures. When the Button is pressed again, the Digital Still Picture Mode is cancelled. ≥We recommend that you press the [CAMERA STILL] Button first at the

position where you want to record the picture and then press the [PHOTO SHOT] Button.

≥For the still pictures taken in the Continuous PhotoShot Mode or Digital Still

Picture Mode, PhotoShot index signals are not recorded.

1tW

5tW

TELE JUMP

≥For other notes, see page 61.

~~~~~~~~~~~~~~~~~~~~~~~~

Zoom In/Out Functions

The Zoom function can be used to record objects close by or to achieve a wide-angle shot.

For wide-angle shots (zoom out):

Press the [W/T] zoom lever towards [W].

10tW

Z.MIC

JUMP

For close-ups (zoom in): Press the [W/T] zoom lever towards [T].

≥Zoom magnification is displayed for a few seconds. ≥Generally speaking, when the [W/T] zoom lever is pressed farther towards

[W] or [T], the zooming speed gradually increases.

1.5 Times Tele Jump Zoom Function

By pressing the [TELE JUMP] Button, the image on the screen will be instantly magnified 1.5 times. ≥The [ ] Indication appears.

JUMP

≥You cannot use the 1.5 Times Tele Jump Zoom Function in the Card Mode.

Taking Close-up Shots of Small Subjects (Macro Close-up Function)

When the zoom magnification is 1a, the Palmcorder can focus on a subject that is as close as approximately 0.8 inches (20 mm) from the lens. With this feature, small subjects such as insects can be recorded.

To Use the Zoom Microphone Function

Along with the zooming operation, the microphone’s directional angle and sensitivity are varied for recording sounds. ≥Set [CAMERA FUNCTIONS] >> [RECORDING SETUP] >> [ZOOM MIC]

>> [ON]. (The [Z.MIC] Indication is displayed.

≥For other notes, see page 61.

)

W.B./SHUTTER/IRIS/

MF/VOL/JOG

D.ZOOM

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

25tW

PUSH

Digital Zoom Function

This function is useful when you want to record close-up shots of subjects located beyond a normal zoom range of 1t to 10t magnification. With the Digital Zoom Function, you can select a magnification of 25t or 700t.

Set [CAMERA FUNCTIONS] >> [CAMERA SETUP] >>

[D.ZOOM] >> [25t

] or [700

tttt

≥25k: Digital zooming to 25t ≥700k: Digital zooming to 700t

To zoom in or out, press the [W/T] zoom lever towards [T] or

towards [W].

Canceling the Digital Zoom Function

Set [D.ZOOM] on the [CAMERA SETUP] Sub-menu to [OFF].

≥For other notes, see page 61.

~~~~~~~~~~~~~~~~~~~~~~~~~

Digital Electronic Image Stabilizer Function

If you are recording in unstable situations and the Palmcorder is shaky, you can use this function to correct for camera shake for these images. ≥If the Palmcorder shakes too much, this function may not be able to

stabilize images.

Set [CAMERA FUNCTIONS] >> [CAMERA SETUP] >> [EIS] >>

[ON].

≥The [EIS] Indication 1 appears.

1, 3

FADE

EIS

Canceling Digital Electronic Image Stabilizer

Set [EIS] on the [CAMERA SETUP] Sub-Menu to [OFF].

EIS function may not work when...

≥Palmcorder movement is too extreme. ≥Recording a subject with distinct horizontal or vertical stripes. ≥Recording in low light situations. ≥Recording a subject under a great amount of fluorescent light.

≥Recording a scene with very fast movement.

≥For other notes, see page 62.

~~~~~~~~~~~~~~~~~~~~~~~~~

Fade In/Out Functions

Fade In

Fade In brings out images and sounds gradually from a black screen at the beginning of a scene.

Hold down the [FADE] Button while the Palmcorder is set to

the Recording Pause Mode.

≥The image fades out gradually.

When the image is completely gone, press the Recording

Start/Stop Button to start recording. Release the [FADE] Button about 3 seconds after starting

recording.

≥The image reappears gradually.

Fade Out

Fade Out causes images and sounds to disappear gradually, leaving a black screen at the end of a scene.

Hold down the [FADE] Button while recording.

≥The image fades out gradually.

About 3 seconds after the image is completely gone, press

the recording Start/Stop Button to stop recording. Release the [FADE] Button.

1 2

≥For other notes, see page 62.

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

CINEMA

Cinema Function

This function is for recording in a cinema-like wide screen.

Set [CAMERA FUNCTIONS] >> [CAMERA SETUP] >>

[CINEMA] >> [ON].

≥Black bars appear at the top and bottom of the screen.

To Cancel the Cinema Mode

Set [CAMERA FUNCTIONS] >> [CAMERA SETUP] >> [CINEMA] >> [OFF].

≥For other notes, see page 62.

~~~~~~~~~~~~~~~~~~~~~~~~

Backlight Compensation Function

This function prevents a recording subject from being recorded too dark in backlight. (Backlight is the light that shines from behind a recording subject.)

Press the [BACKLIGHT] Button.

≥The [ª] Indication 1 flashes and then is displayed.

To resume normal Recording

Press the Backlight Button [BACKLIGHT].

≥When the [BACKLIGHT] Button is pressed, the entire screen becomes

brighter.

≥By operating the [OFF/ON/MODE] Switch, the Backlight Compensation

Function is cancelled.

≥This function cannot be used when the Iris is set.

BACKLIGHT

~~~~~~~~~~~~~~~~~~~~~~~~

MagicPix Function

This function allows you to record color images brightly in a dark place without using a light.

Press the [MAGICPIX] Button.

≥The [MAGICPIX] Indication 1 appears.

To Cancel the MagicPix Function

Press the [MAGICPIX] Button.

≥For other notes, see page 62.

MAGICPIX

MANU

FOCUS

UICK

QUICK

START

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

Quick Start

When this feature is activated, you can resume recording quickly even if the Palmcorder goes into standby mode (when left in Pause mode for 5 minutes). Palmcorder will be ready for shooting in approximately 1.5 seconds when the Power switch is turned [OFF] and back to [ON] again. To activate this feature, press the [QUICK START] button to turn on the Quick Start Lamp.

Press the [QUICK START] Button.

≥The Quick Start Recording Lamp 1 lights up.

Set the [OFF/ON/MODE] Switch to [OFF].

≥The Quick Start Recording Lamp remains lit.

Set the [OFF/ON/MODE] Switch to [ON].

≥The Palmcorder will be ready for recording in approximately

1.5 seconds.

≥For other notes, see page 62.

~~~~~~~~~~~~~~~~~~~~~~~~~

Wind Noise Reduction Function

This function reduces the noise that the wind makes as it hits the microphone during recording.

Set [CAMERA FUNCTIONS] >> [RECORDING SETUP] >>

[WIND-CUT] >> [ON].

≥The [WIND-CUT] Indication 1 appears.

To Cancel the Wind Noise Reduction Function

Set [CAMERA FUNCTIONS] >> [RECORDING SETUP] >> [WIND CUT] >> [OFF].

≥For other notes, see page 62.

~~~~~~~~~~~~~~~~~~~~~~~~~

WIND- CUT

Recording in Special Situations

Select optimal automatic exposures under specific recording situations.

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication appears.

Set [CAMERA FUNCTIONS] >> [CAMERA SETUP] >>

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

[PROG.AE] >> a desired Mode [

≥The Indication of the selected Mode is displayed.

[5] Sports Mode

For recording scenes involving quick movements, such as sports scenes.

[7] Portrait Mode

AUTO MANU

AL FOCUS

Focuses on the main subject of the image and leaves the background slightly out of focus.

[4] Low Light Mode

Preserves the mood of dim light settings without altering picture brightness.

[Ω] Spotlight Mode

Neutralizes the additional brightness created by a spotlight.

[º] Surf & Snow Mode

Compensates for excessive illumination from sun glare to produce a clear

picture.

Canceling the Program AE Function

Set [PROG.AE] on the [CAMERA SETUP] Sub-Menu to [OFF]. Or, set the

Mode Selector Switch to [AUTO].

≥For other notes, see page 62.

(Program AE)

], [7], [4], [Ω], [º].

MANU

FOCUS

2, 3

MANU

FOCUS

W.B./SHUTTER/IRIS/

MF/VOL/JOG

AUTO MANU

AL FOCUS

PUSH

Manual Shutter Speed Adjustment

Useful for recording fast-moving subjects.

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication 1 appears.

Press the [PUSH] Dial repeatedly until the shutter speed

appears.

Indication Rotate the [PUSH] Dial to adjust the shutter speed.

The Range of Shutter Speed Adjustment

1/60– 1/8000 The standard shutter speed is 1/60 second. Selecting a speed closer to [1/8000] causes the shutter speed to be faster, resulting in crisper captures of moving subjects but a lower light level. ≥When the progressive function is [ON], a speed only up to 1/500 can be

used.

1, 2

2, 3

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

AUTO MANUAL

FOCUS

W.B./SHUTTER/IRIS/

MF/VOL/JOG

AUTO MANU

AL FOCUS

MNL

F2.0

PUSH

1/1000

1/60

MNL

1 2

To Resume Automatic Adjustment

Set the Mode Selector Switch to [AUTO].

≥For other notes, see page 63.

~~~~~~~~~~~~~~~~~~~~~~~~

Manual Iris Adjustment

You can use this function when the screen is too bright or too dark.

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication 1 appears.

Press the [PUSH] Dial repeatedly until the Iris Indication 2

appears. Rotate the [PUSH] Dial to adjust the iris.

Adjustable Range of the Iris

CLOSE (Closed), F16, ..., F2.0, OP (Opened) i0dB, ..., OPi18dB When the Gain-up Mode [GAIN-UP] is used. Iris adjustment is by OPi15dB. When a value closer to [CLOSE] is selected, the image becomes darker. When a value closer to [OPi18dB] is selected, the image becomes brighter. The value to which idB is attached indicates a gain value. If this value is too large, the quality of the image deteriorates.

To Resume Automatic Adjustment

Set the Mode Selector Switch to [AUTO].

≥For other notes, see page 63.

(F Number)

~~~~~~~~~~~~~~~~~~~~~~~~

Manual Focus Adjustment

Focus can be adjusted manually for recording in a situation where auto focus may not function well.

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication 1 appears.

Set the Mode Selector Switch to [FOCUS].

≥The [1MF] Indication (Manual Focus Mode) 2 appears.

Rotate the [PUSH] Dial to adjust the focus.

To Resume Automatic Adjustment

Set the Mode Selector Switch to [AUTO].

MNL

MANU

AL FOCUS

2, 3, 4

W.B./SHUTTER/IRIS/

MF/VOL/JOG

2, 3

W.B./SHUTTER/IRIS/

MF/VOL/JOG

AUTO MANU

AL FOCUS

1AWB

PUSH

AUTO MANU

AL FOCUS

MNL

PUSH

1 2

Recording in Natural Colors

Depending on the scene or light conditions, the Automatic White Balance Adjustment Mode may not be able to bring out natural colors. In such a case, the white balance can be adjusted manually.

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication appears.

Press the [PUSH] Dial.

≥The [AWB] Indication appears.

Rotate the [PUSH] Dial to set a desired White Balance Mode.

Automatic White Balance Adjustment [AWB]

Indoor Mode (shooting under incandescent lighting) [{]

Outdoor Mode [z]

Fluorescent light Mode [|]

The White Balance setting that was previously set manually [1]

To Resume Automatic Adjustment

Rotate the [PUSH] Dial until the [AWB] Indication appears. Or, set the Mode Selector Switch to [AUTO]. ≥When power is turned on with the Lens Cap on, the Automatic White

Balance Adjustment may not function properly. Please turn on the Palmcorder after removing the Lens Cap.

≥For other notes, see page 63.

(White Balance)

~~~~~~~~~~~~~~~~~~~~~~~~~

Adjusting White Balance Manually

When the Auto White Balance Adjustment function does not operate suitably under the existing light conditions, use the Manual White Balance Adjustment mode.

Set the Mode Selector Switch to [MANUAL].

≥The [MNL] Indication 1 appears.

Press the [PUSH] Dial.

≥The [AWB] Indication appears.

Rotate the [PUSH] Dial until the [1] Indication 2 is

displayed. Point the Palmcorder at a full-screen white subject, and then

keep the [PUSH] Dial pressed until indication [ flashing.

≥When the [1] Indication flashes after turning the Palmcorder on, the

previously adjusted white balance setting is still kept.

To Resume Automatic Adjustment

Rotate [PUSH] Dial until the [AWB] Indication is displayed. Or, set the Mode Selector Switch to [AUTO].

] stops

10 000K

9 000K 8 000K

7 000K

6 000K

5 000K

4 000K

3 000K

2 000K

10)

1 000K

ª About White Balance Sensor

The White Balance Sensor 3 determines the nature of the light source during recording. ≥Do not cover the White Balance Sensor with your hand during recording.

Otherwise, White Balance will not work normally.

Use of Auto White Balance Adjustment in inappropriate lighting conditions may result in reddish or bluish images. Where the subject is found on the left, but surrounded by many light-sources, Auto White Balance Adjustment may not operate properly. In such a case, we suggest that you adjust the White Balance.

1) The range that is controlled by the Auto White Balance Adjustment Mode of this Palmcorder

2) Blue sky

3) Cloudy sky (Rain)

4) TV screen

5) Sunlight

6) White fluorescent light

7) Halogen light bulb

8) Incandescent light bulb

9) Sunrise and sunset

10) Candlelight

≥For other notes, see page 63.

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

Using the Free Angle Flash

The Built-in Flash enables you to record still pictures in a dark place. Rotating the Flash enables you to light up objects from the upper angle even if the Palmcorder is inclined horizontally.

Set [CAMERA FUNCTIONS] >> [RECORDING SETUP] >>

[FLASH] >> [ON] or [AUTO].

≥If [AUTO] is selected, Flash is lighted if light is needed by sensing the

surrounding luminosity.

Rotate the Flash to [ON].

≥When it is set to [ON] or above, this flash will be ready for use.

Press the [CAMERA STILL] Button.

≥Flash is activated.

Press the [PHOTO SHOT] Button or Recording Start/Stop

Button.

≥Flash is not lit, when the Palmcorder is in recording mode.

PHOTO SHOT

≥If either [ß], [ßi] or [ßj] Indication is lit, flash will light. If [ß] is flashing

or not displayed, Flash will not fire.

≥Do not cover the Flash Sensor

Adjusting Brightness of the Flash

Set [CAMERA FUNCTIONS] >> [RECORDING SETUP] >> [FLASH LEVEL] >> a desired Flash Level. ≥For recording under normal conditions, set it to [NORMAL]. (The [ß]

Indication

appears).

≥If the brightness is not enough in [NORMAL] setting, set it to [i] (the [ßi]

Indication appears), if it is too bright, set it to [j] (the [ßj] Indication appears).

To reduce the “Red Eye” effect

[CAMERA FUNCTIONS] >> [RECORDING SETUP] >> [RED EYE REDUCTION] >> [ON]. ≥The [£] Indication

appears.

with your hand during recording.

CAMERA STILL

FLASHONOFF

ß£

≥For other notes concerning this item, see 63.

1) MULTI 2) P-IN-P

3) WIPE 4) MIX

5) STROBE

6) GAIN-UP 7) TRAIL

8) MOSAIC 9) MIRROR

Digital Effect Functions

This Palmcorder is equipped with digital effect functions that add special effects to the scene.

Digital Effects 1 [EFFECT1]

1) [MULTI] Multi-Picture Mode

2) [P-IN-P] Picture-in-Picture Mode

3) [WIPE] Wipe Mode

4) [MIX] Mix Mode

5) [STROBE] Strobe Mode ≥Records images with a stroboscopic effect.

6) [GAIN-UP] Gain-up Mode

≥Brightens images electronically. ≥Adjust focus manually when using this Mode.

7) [TRAIL] Trailing Effect Mode ≥Records images with a trailing effect.

8) [MOSAIC] Mosaic Mode ≥Produces a mosaic-like image.

9) [MIRROR] Mirror Mode ≥The right half of an image becomes a mirror image of the left half.

Digital Effects 2 [EFFECT2]

10) [NEGA] Negative Mode ≥The colors of the recorded image are inverted as seen in a negative.

11) [SEPIA] Sepia Mode ≥Records a scene with a brownish tint, like the color of old pictures.

12) [MONO] Black & White Mode ≥Records an image in black and white.

13) [SOLARI] Solarization Mode ≥Records an image with a painting-like effect.

10) NEGA 11) SEPIA

12) MONO 13) SOLARI

1, 2

W.B./SHUTTER/IRIS/

MF/VOL/JOG

PUSH

3, 4, 5

MIX

WIPE

Selecting a desired digital effect

Set [CAMERA FUNCTIONS] >> [DIGITAL EFFECT] >> [EFFECT1] or [EFFECT2] >> a desired digital effect.

Canceling the digital effect

Set [CAMERA FUNCTIONS] >> [DIGITAL EFFECT] >> [EFFECT1] or [EFFECT2] >>[OFF].

≥If the Palmcorder is turned off, the [EFFECT2] settings are cancelled.

≥For other notes, see page 63.

ª Wipe Mode and Mix Mode

Wipe Mode:

Like a curtain being pulled, the still picture of the last recorded scene gradually changes to the moving image of a new scene.

Mix Mode:

While the moving image of a new scene fades in, the still image of the last recorded scene gradually fades out.

Set [DIGITAL EFFECT] >> [EFFECT1] >> [WIPE] or [MIX].

Exit the menu by pressing the [MENU] Button.

≥The [WIPE] or [MIX] Indication appears.

Press the Recording Start/Stop Button to start the

Recording. Press the Recording Start/Stop Button to pause the

Recording.

≥The last scene is stored in memory. The [WIPE] or [MIX] Indication

changes to [B] or [C].

Press the Recording Start/Stop Button to restart the

Recording.

≥The last image of the previous scene gradually changes to the new

scene.

≥For other notes, see page 63.

PHO SHO

11, 2

W.B./SHUTTER/IRIS/

MF/VOL/JOG

11, 2

W.B./SHUTTER/IRIS/

MF/VOL/JOG

ª Multi-Picture Mode

PHO

SHO

PUSH

MULTI/ P-IN-P

PHO

SHO

Strobe Multi-Picture Mode 1:

You can capture and record 9 consecutive small still pictures.

Manual Multi-Picture Mode

You can manually capture and record 9 small still pictures.

After setting [CAMERA FUNCTIONS] >> [DIGITAL EFFECT] >>

[EFFECT1] >> [MULTI].....

Set [MULTI-PICTURES] >> [SCAN MODE] >> [STROBE] or

[MANUAL].

When [STROBE] is selected:

≥Set the [SPEED] to a desired strobe speed.

[FAST]: You can capture 9 consecutive still pictures within

approximately 1 second

[NORMAL]:

You can capture 9 consecutive still pictures within approximately 1.5 seconds

[SLOW]: You can capture 9 consecutive still pictures within

approximately 2 seconds

≥If you set [SWING] on the [MULTI-PICTURES] Sub-Menu to [ON], the

intervals at which the 9 still pictures are taken are longer at the beginning and end than in the middle of the swing strobe period, and it is useful for analyzing swing motion, etc., in sports.

When [MANUAL] is selected:

≥You can select a desired scene one at a time up to 9 small pictures.

Exit the menu by pressing the [MENU] Button.

Press the [MULTI] Button.

≥If [MANUAL] is selected, press the [MULTI] Button at each scene you

want to capture.

Press the Recording Start/Stop Button or the [PHOTO SHOT]

Button to record on the Cassette.

Deleting all the captured Multi-Pictures

While 9 multi-pictures are displayed, press the [MULTI] Button. ≥If [MANUAL] has been selected, press the [MULTI] Button after 9 pictures

are displayed.

To Display the Multi-Pictures again

Press the [MULTI] Button for 1 second or longer.

To Delete Multi-Pictures one by one (When pictures were captured in [MANUAL])

When the [MULTI] Button is pressed for 1 second or longer while the still pictures are displayed, the picture captured last is deleted. If you keep pressing the [MULTI] Button, the pictures are deleted continuously.

≥After still pictures are deleted, they cannot be displayed again.

≥For other notes, see page 63.

MULTI/ P-IN-P

ª Picture-in-Picture Mode

You can display a sub-screen (still picture) inside the screen.

After setting [CAMERA FUNCTIONS] >> [DIGITAL EFFECT] >>

[EFFECT1] >> [P-IN-P]......

Select [P-IN-P] on the [MULTI-PICTURES] Sub-Menu and set

the position (

1234

picture. Exit the menu by pressing the [MENU] Button.

Aim the Palmcorder at the scene you want to capture and

press the [P-IN-P] Button to insert a small still picture.

≥A small still picture is displayed in a Normal picture. ≥If the [P-IN-P] Button is pressed again, the small still picture is cleared.

Press the Recording Start/Stop Button or the [PHOTO SHOT]

Button to record on the Cassette.

≥For other notes, see page 63.

) where you want to insert a small still

+ 134 hidden pages