Panasonic PV-D4763S, LSQT0676A User Manual

DVD/VCR DECK

Operating Instructions

Model No.

PV-D4763S

LSQT0676A

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Important Safeguards and Precautions

FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY
AND OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON THE UNIT

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the
unit or in this manual. If necessary, have your
Electric Utility Service Company or Video Products
Dealer verify the power source in your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either
a polarized power cord plug (one blade is wider

than the other), or a three-wire grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you cannot

fully insert the plug, try reversing it. If it still will not fit,
have an electrician install the proper wall outlet. Do not
defeat the safety feature by tampering with the plug.

GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding

outlet. If necessary, have an electrician install the
proper outlet. Do not defeat the safety feature by
tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they

are not likely to have anything rest on them, roll

over them, or be in the way of walking traffic.

If an extension cord is used, make sure it also

has either a polarized or grounded plug and that

the cords can be securely connected.

Frayed cords, damaged plugs, and damaged or

cracked wire insulation are hazardous and should

be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire

hazards and should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat

generated during operation. If they are blocked,

heat build-up inside the unit can cause failures that

may result in a fire hazard or heat damage to

cassettes or discs.

For protection, follow these rules:

a. Never cover ventilation slots or the unit while in

use, or operate the unit when placed on a bed,
sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case

or rack, unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS

OR SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or

radiator, in direct sunlight, inside closed vehicles,

in high temperature [over 104°F (40°C)], or in over

75% humidity. If the unit is suddenly moved from

a cold place to a warm one, moisture may

condense in the unit and on the tape causing

damage. Never subject the unit to vibration,

impact, or place it so that the surface is tilted as

internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a sloping
surface.

• Do not place this unit on any support that is not
firm, level, and adequately strong.
The unit could fall causing serious
injury to a child or adult and
damage to the unit.

• An appliance and cart
combination should be moved
with care. Quick stops,
excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.

• Carefully follow all operating instructions and
use the manufacturer's recommended
accessories when operating this unit or
connecting it to any other equipment.

2

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded
so as to provide some protection against built up static
charges and voltage surges.
Section 810 of the National Electrical
Code, ANSI/NFPA 70 (in Canada,
part 1 of the Canadian Electrical
Code) provides information
with respect to proper grounding
of the mast and supporting
structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes and requirements for the grounding electrode.

2

KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS

An outside antenna system should be located well away from
power lines, electric light or power circuits and where it will never
come into contact with these power sources if it should happen
to fall. When installing an outside antenna, extreme care should
be taken to avoid touching power lines, circuits or other power
sources as this could be fatal. Because of the hazards involved,
antenna installation should be left to a professional.

If the unit has been in storage or moved to a new location,
refer first to the INSTALLATION section of these safeguards.

1

KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.

2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR

STRONG IMPACT, unplug the unit and have it inspected by a

qualified service technician before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or
before leaving the unit unused for extended periods of time,
disconnect all equipment from the power source as well as
the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE

• Never drop or push any object through openings in the unit.

• Avoid placing the unit directly above or below your TV set

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated
cloth to gently remove dust or debris. DO NOT USE cleaning
fluids, aerosols, or forced air that could over-spray, or seep
into the unit and cause electrical shock. Any substance such
as wax, adhesive tape, etc. may mar the cabinet surface.
Exposure to greasy, humid, or dusty areas may adversely
affect internal parts.

1 DO NOT SERVICE THIS PRODUCT YOURSELF

2 IF REPLACEMENT PARTS ARE REQUIRED

3

OUTDOOR ANTENNA INSTALLATION

NEC

- NATIONAL
ELECTRICAL CODE

ELECTRIC
SERVICE
EQUIPMENT

USING THE UNIT

if liquid has been spilled into the unit. Immediately unplug
the unit, and have it inspected by a service technician.
Fire and shock hazards can result from electrical shorts
caused by liquid contact inside.

Some internal parts carry hazardous voltages and contact
can cause electric shock or fire hazard.
Do not put any foreign object on the disc tray.

as this may cause electrical interference. Keep all magnets
away from electronic equipment.

SERVICE

If, after carefully following the detailed operating
instructions, this product does not operate properly, do not
attempt to open or remove covers, or make any
adjustments not described in the manual. Unplug the unit
and contact a qualified service technician.

Make sure the service technician uses only parts specified
by the manufacturer, or those having the same safety
characteristics as the original parts. The use of unauthorized
substitutes may result in fire, electric shock, or other hazards.

HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service
technician to conduct a thorough safety check as
described in the manufacturer’s service literature to ensure
that the unit is in safe operating condition.

GROUND
CLAMP

ANTENNA
LEAD IN
WIRE

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)

1

Safety Precautions/Mesures de sécurité

WARNING: To prevent fire or shock hazard, do not expose this

equipment to rain or moisture.

CAUTION: To prevent electric shock, match wide blade of plug to

wide slot, fully insert.

Avertissement: Afin de prévenir tout risque d’incendie ou de chocs

électriques, ne pas exposer cet appareil à la pluie ou
à une humidité excessive.

Attention: Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de la
prise et pousser jusqu’au fond.

This symbol warns the user that uninsulated voltage

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

within the unit may have sufficient magnitude to cause
electric shock.
Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.

This symbol alerts the user that important literature
concerning the operation and maintenance of this unit
has been included. Therefore, it should be read
carefully in order to avoid any problems.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE
YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER
OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when operated in a residential
environment. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, use the equipment in another location and/or utilize
an electrical outlet different from that used by the receiver.
If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the
booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure contin ued compliance, (example- use only shielded interface cables when connecting to
other devices.) Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.

FCC Warning: Any unauthorized changes or modifications to this equipment would void the user’s

authority to operate.

CAUTION:

LASER RADIATION
WHEN OPEN DO NOT
STARE INTO BEAM.

ATTENTION:

RAYONNEMENT
LASER EN CAS
D’OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.

(Inside of product)

Region Management Information:

This DECK is designed and manufactured to respond to the
Region Management Information that is recorded on a DVD
disc. If the Region number described on the DVD disc does
not correspond to the Region number of this DECK, this
DECK cannot play this disc.

●The Region number for this DECK is “1”.

●The Player will play DVD-Video marked with labels

containing “1” or “ALL”.

Example:

ALL

1

2

4

3

Before Using

Congratulations

on your purchase of one of the most
sophisticated and reliable products on the
market today. Used properly, it will bring you
years of enjoyment. Please fill in the information
below. The serial number is on the tag located
on the back of your DECK.

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.

• Serial No.

Accessories

Remote Control

LSSQ0377

Loading the Batteries

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

Record/ Playback Time

Only use tapes with the mark in this DECK.

Tape Speed

Setting

SP

(Standard Play)

LP

(Long Play)

SLP

(Super Long Play)

4

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

PV-D4763S

Batteries 2 “AA”

RF Coaxial Cable
LSJA0372

To order accessories,
call toll free
1-800-332-5368.

1) Open cover.

2) Insert batteries as
marked.

3) Close cover.

Type of Video Cassette

T160T120T60

1 Hour 2 Hours
2 Hours 4 Hours

3 Hours 6 Hours 8 Hours

2 Hours

40 Minutes

5 Hours

20 Minutes

Head Cleaning

Playing older or damaged tapes may eventually cause
video heads to become clogged.

Video Head Clog Sensor

During playback, this screen
appears if clogging is detected.
To remove screen, press PLAY
on the remote or DECK.

• Use “dry” type head cleaning cassette only.

(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your
nearest servicenter by visiting our Web Site
(see p. 65).

V I D

EO HEADS MAY

N

EED

CLEAN I NG
PLEASE I NSERT HEAD
CLEAN I NG CASSETTE
OR REFER

TO

MANUAL

END

: PL

AY

Built-in Head Cleaner

A clean video head helps produce a clear picture.
So, we have equipped your DECK with a built-in,
non-chemical head cleaning system that helps
prevent clogging of the video heads.
Cleaning is performed each time you load or unload
a video cassette.

• This feature is preventative only, If your video heads
are seriously clogged, consider the use of a chemical
non-abrasive head cleaning kit or take your DECK to
a Servicenter.

Features for a Quality Picture (VCR)

Digital Auto Picture

Automatically controls the video output signal for
less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for
optimum picture quality.

Manual Tracking Control
(to reduce picture noise)

Use during Playback and Slow Motion mode to
reduce picture noise.
Press CH (TRACKING) / on the remote control
or on DECK until the picture clears up.
To return to Auto Tracking, press POWER off, then
on again a few seconds later.

R

R

R

R

V-Lock Control (to reduce picture jitter)

In Still mode, CH (TRACKING) / operate as a
V-Lock control.

R

R

R

R

Table of Contents

DVD / VCR

Important Safeguards and Precautions ............................2, 3

Before Using............................................................................4

DECK / Disc / Cassette Information .................................. 6 , 7

Location of Controls ....................................................... 8 ~ 10

Displays (On Screen Displays and Multi Function Display)....................11

Connections .................................................................. 12 ~ 15

Initial Setup for Basic Connections (Ready to Play) ..........16, 17

VCR
Reset Language, Channels, Clock, VCR’s Output Channel ... 18, 19

Playback/ Record on a Tape...........................................20, 21

DVD

Basic DVD Operation ......................................................22, 23

Timer Recording..............................................................24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System ....................26, 27

Multi-Brand Control Feature ...........................................28, 29

Tape Operation (Search System) .......................................30 ~ 32

Special VCR Features .....................................................33, 34

Copying Your Tapes (Dubbing) ......................................................... 35

(Connection)

Initial Setup

Operation

Basic

Operation

VCR

Disc Operation ...............................................................36 ~ 41

DVD-RAM Operation (DVD-RAM only)................................. 42, 43

DVD Operation using On-Screen Displays .................44 ~ 48

MP3/WMA/JPEG Playback Operation ..........................49 ~ 51

DVD Lock Feature .................................................................52

Settings for DVD Operation ..........................................53 ~ 57

SD Card............................................................................ 58, 59

Language Code List..............................................................60

DVD / VCR

Warning and Instruction Displays........................................61

Before Requesting Service.............................................62, 63

Limited Warranty ............................................................. 64, 65

Customer Services Directory ...............................................65

Spanish (Español) Quick Use Guide............................66 ~ 71

Index..................................................................................... BC

Operation

DVD

Information

For Your

5

DECK / Disc / Cassette Information

Prevent Accidental Tape Erasure

Break off the tab to
prevent recording.

Record Tab

Screw driver

To record again

Cover the hole
with cellophane tape.

Cleaning DECK

Use a soft cloth or dusting attachment of a vacuum
cleaner to remove dust from the ventilation holes on
the back sides and bottom of the cabinet. Plastic
surfaces are easily scratched and can be marred
by alcohol and various solvents. Avoid excessive
use of oil-based furniture polishes since the
materials used in the cabinet will accumulate more
dust. We recommend using a non-abrasive,
antistatic cleaner and polisher.

Disc formats supported by this DECK

DECK can play back discs bearing any of the
following marks:

Logo Disc type

DVD-RAM (Version 1.1 of the
Video Recording Format a
unified video recording
standard)

DVD (DVD-Video)
DVD-R (DVD-Video formatted

discs [finalized])
DVD-Audio

DVD-RAM discs

DVD-RAM discs must meet the following conditions
for this unit to be able to play them.

Type

Capacity

• Remove TYPE 2 and 4 discs from their cartridges
before use, then return them when you are finished.
Read the instructions for the disc carefully.

• Some parts of the disc, for example where one program

ends and another begins, may not play smoothly.

• Non-cartridge discs

• Discs that can be removed from

their cartridges (TYPE 2 and 4)

• 12 cm (5”) 9.4 GB (double-sided)
and 4.7 GB (single-sided)

• 8 cm (3”) 2.8 GB (double-sided)

Video CD
CD (CD-DA)

CD-R/CD-RW (CD-DA,Video
CD formatted discs [finalized])

WMA, MP3, JPEG

[Discs Played 8cm (3") or 12cm (5")]

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• PAL discs (the audio on DVD-Audio can be

played), DVD-ROM, DVD-RW, DVD+RW,
CD-ROM, CDV, CD-G, CVD, SVCD, SACD,
Divx Video Disc and Photo-CD

6

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Specifications

Power Source: 120 V AC, 60 Hz
Power Consumption: Power On: Approx. 32 watts, Power Off: Approx. 4 watts

Video Signal: EIA Standard NTSC color
Video Recording System: 4 rotary heads helical scanning system

Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound)
Tuner:
Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output
Input Terminal: Audio/Video Line Input (Front)
Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)

Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity: 10 % ~ 75 %
Weight: 4.9 kg (10.8 lbs).
Dimensions: 430 (W) x 95.5 (H) x 344 (D) mm

Discs Played
(1) DVD-Video Disc 5” (12 cm) single-sided single-layer

DVD-Audio Disc 5” (12 cm) single-sided double-layer

DVD-RAM Disc 5” (12 cm) 9.4 GB (double-sided) and 4.7 GB (single-sided)

(2) Compact Disc 5” (12 cm) disc

(CD-DA, Video CD) 3” (8 cm) disc
(CD-R/CD-RW , MP3, WMA, JPEG)

Digital Audio Output: Digital Optical Connector
Pickup: Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)

Note: • Designs and specifications are subject to change without notice.

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Audio Output 2 (L), (R)

16-15/16” (W) x 3-12/16” (H) x 13-9/16” (D) inch

5” (12 cm) double-sided double-layer (one layer per side)
3” (8 cm) single-sided single-layer
3” (8 cm) single-sided double-layer
3” (8 cm) double-sided double-layer (one layer per side)

3” (8 cm) 2.8 GB (double-sided)

Laser power: CLASS II

(Connection)

Initial Setup

Definition of Terms (DVD)

Angle: Some DVD discs feature scenes simultaneously shot from different angles.

Chapter Number: Titles are subdivided into numbered sections. You can quickly search for
DVD: A high-density optical disc on which high-quality pictures and sound have

Playback Control: With Video CD (version 2.0), scenes or information may be selected for viewing
Subtitles: Written dialogue which appears at the bottom of the screen.

Time Number: The elapsed play time from the start of a disc or title. Use to quickly find
Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.

Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks to
Video CD: CD containing picture and sound with same quality level as video tape.

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093,
licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by method claims of
certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

The ANGLE button can be used to view the scene from different angles.
(ANGLE Indicator lights on DECK when a scene recorded at different angles
is detected.)

a favorite scene using these numbers.
been digitally recorded. DVD incor porates new video compression technology

(MPEG II) and high-density recording technology which allow entire movies to
be recorded with incredible playback quality.

or listening from an interactive menu that appears on the TV screen.

scenes. (May not work with some discs.)

be quickly located.
This DECK also supports Video CDs with playback control (version 2.0).

7

Location of Controls

Remote Control

Bold: VCR Function

Italic

:

Bold Italic:VCR and DVD Functions

Normal: Others

DVD Function

8

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Front View of DECK

Front View of DECK

Bold: VCR Function

Italic

:

DVD Function

:

Bold Italic

Normal: Others

STOP/EJECT

p. 20

FAST FORWARD/SEARCH

p. 20

PLAY

p. 20

REWIND/SEARCH

p. 20

Remote
Sensor

POWER

VCR and DVD Functions

If the disc cannot be removed...

First, unplug DECK. Then, prepare a rigid
wire (e.g. an extended paper clip) and,
applying moderate force, insert it straight
into the hole at the base of the tray.
The tray will eject a little. Now, pull the tray
all the way out and remove the disc.

Over 2 inches

Cassette
Compartment

Disc Tray

OPEN/CLOSE

p.

22

(Connection)

Initial Setup

Audio/Video
Input Connector 2
(LINE 2)

CHANNEL /
TRACKING/V-LOCK

pp. 4, 21

REC

p. 21

p. 35

Multi Function

Display

p. 11

SD Card slot

PROGRESSIVE

SKIP
SKIP

Reset All Memory Functions

Use when moving DECK to new location, or if a mistake was made in the Initial
Setup section (return to Factory Setting).

• Make sure a tape is not inserted in the DECK.
Turn DECK Power on.

1

Press and hold both VCR PLAY

2

and CHANNEL
more than 5 seconds.

• The power shuts off.
Do “Initial Setup (Ready to Play)”

3

21

on page 16.

on the DECK for

p. 58

PAUSE

PLAY
STOP

p. 10

p.

23

p. 23

p.

22

p.

22

9

Location of Controls (continued)

Rear View of DECK

AC Power Plug

• While plugged into an AC outlet,
this DECK consumes 4 W of
electrical power in off mode.

Component Video Output
Connector (Y, PB, PR) (DVD Only)

p.

13

Bold: VCR Function

Bold Italic:VCR and DVD Functions

VHF/UHF Antenna Output Terminal
p. 12

VHF/UHF Antenna Input Terminal
p. 12

Video Output
Connector

p.

12

Italic:DVD Function

Video Input
Connector
p. 35

5.1ch Analog Audio Output
Connector (CENTER, SUB WOOFER,
SURROUND L/R, FRONT L/R)

p.

(DVD Only)

Optical Digital Audio
Output Connector
(DVD Only)

p.

15

15

S-Video Out
Connector
(DVD Only)

pp.

10, 13

••

Audio Output 2
Connector (L/R)

p.

13

Audio Output 1

•

Audio Input
Connector (L/R)

p.

35

Connector (L/R)

p.

12

The following table shows the status of the output jacks when in VCR or DVD mode.

VCR

DVD

Video Output
Audio Out 1
Audio Out 2

YES
YES

Component
Video Output

N/A

S-VIDEO OUT

N/A

YES

• PROG functions on the remote are not available when using Component Video Output

Note

and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press
PROG.

To enjoy PROGRESSIVE SCAN video

(1).Connect

(See p. 13.)

(2).When the PROGRESSIVE button is pressed, the ON lamp lights up (see p. 9) and the

PROGRESSIVE SCAN signal is output from the

Notes

• The PROGRESSIVE button can be operated when the DECK is in DVD function mode.

• The screen may shift off-center when using progressive output. Please adjust the screen

position if this occurs. (Refer to your TV manual.)

• The DECK outputs video signals (not PROGRESSIVE SCAN) from the “VIDEO OUT” and
“S-VIDEO OUT” terminals when the ON lamp is lit.

10

Component Video Output

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

to the component video input terminals of a television.

Component Video Output Connector

.

DIGIT

Displays (On Screen & Multi Function)

On Screen Displays (VCR)

Function & Channel Displays

CH 0 8

When a function button
is pressed, e.g. PLAY,
or you change
channels, a 5-second
display appears.

VCR Status & Clock Displays
To display or remove
overlay at right,

➛➛

➛ press DISPLAY.

➛➛

Rec Time Remaining
(OTR mode only,
see p. 21.)

Multi Function Display

VCR mode Indicator

Lights up when
DECK is VCR mode.

Timer Indicator

Lights up when
DECK is set for
Timer Recording,
or when One
Touch Recording
(OTR) is used.
Flashes when
Timer Recording is
set, but a tape has
not been inserted
into DECK and
when a power
interruption occurs
during Timer
Programming.

DTS Indicator

Lights up when DTS
formatted DVD is played.
(DVD only)

Dolby Digital
Indicator

Lights up when “Dolby Digital”
formatted DVD is played.
(DVD only)

Tape Indicator

Lights up when a tape
is inserted.

VCR

TIMER REC

DIGIT

Hi-Fi Indicator

Lights up when
Hi-Fi audio is
monitored in Play
mode.

Function Status

Broadcast Audio
Being Received
(See p. 26.)

VCR REC Indicator

Lights up during
recording.

Hi - Fi

AL

Blank Tape/ No Video Signal
Indications

Whenever a blank section of a tape
comes up in Play mode, or when the
selected channel has no broadcast
signal with Weak Signal Display
Feature (p. 33) set to OFF, the TV
screen will turn solid blue.

Current Time

REC

1 2 : 0 0A
0 : 25
STER

EO
SAP
M

ONO

DISC Indicator

Lights up when a
disc is inserted.

M

-0 : 1 2 : 3 4

Channel

CH 02

SP

Counter

Tape Speed
(See p. 4.)

DVD mode Indicator

Lights up when
DECK is DVD mode.

CD/MP3/WMA
Indicator

CD :Lights when a

Video or Audio
CD is inserted.

MP3/WMA :

Lights when an
MP3 or WMA
file is played.

CD

AM
PM

MP3

ANGLE

DVD

WMA

ANGLE Indicator

AM/PM
Indicator

Lights up when a
scene recorded at
different angles is
detected.
(See p. 37.)
(DVD only).

Clock/ Status/ Channel/ Speed Display

Displays the current time. Briefly displays DECK
status when a function button is pressed. Briefly
displays the channel number, or “L1” or “L2”
when a channel or line input is selected. Briefly
displays the recording speed when SPEED is
pressed.

(Connection)

Initial Setup

11

Connections

Basic Connections

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

• Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable
(not supplied) as shown in the figure below.

■ ■

■ ■

■ DSS Receiver DECK TV

■ ■

■ ■

■ DECK TV

■ ■

Antenna or Cable

■ Cable Box DECK TV

■ ■

b

DSS
Receiver

IN

IN

OUT

or

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VIDEO

L

AUDIO

R

WARNING

When using “Nut type” RF coaxial cables, tighten with
fingers only. Overtightening may damage terminals.

VHF/UHF

OUT TO TV

IN

OUT

Cable Box

1 Disconnect antenna or cable from TV

and connect to DECK.

2 Connect DECK to TV with RF Coaxial Cable.

RF COAXIAL CABLE

a

TV

AUDIO IN

R

(supplied)

VIDEO

IN

L

b

AV CABLE

VHF/
UHF

(not supplied)

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the
NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.

12

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Other Connections

■ ■

■ With a Cable Box (DECK

■ ■

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VHF/UHF

OUT TO TV

■■

■

Connect With Two Cable Boxes

■■

ANT or CATV

Cable Box

Cable Box TV)

OUTIN

DVD/VCR DECK

ANT

or

CATV

Cable Box

OUT

IN

2-Way Splitter

OUT 1

OUT 2

OUT

Cable Box

OUTIN

IN 1

IN FROM ANT.

VHF/UHF
OUT TO TV

A/B Switch

VHF/
UHF

IN 2IN 1

• view any
(including

• use Remote

• record and view

TV

AUDIO

VIDEO

scrambled)
channel.

Control to select
channels without
using Multi-brand
control feature.

both scrambled
and unscrambled
channels if
additional
equipment is
added.
This connection
requires: two
converter boxes,
an A/B switch,
and a 2-way
splitter.

TV

IN

OUT

R

AUDIO

L

VIDEO

IN

OUT

R
L

VHF/
UHF

You CannotYou Can

• record
scrambled
channels.

You CannotYou Can

• view a channel
other than the
one selected
for any type of
recording.

• do a Timer
recording of a
channel unless
you select it on
the Cable Box.

Connections For DVD Only (enjoying higher picture quality)

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT

1

or S-VIDEO mode).
If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.

2

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to
S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

3

Notes

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV,

and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only
from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT
Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

• TV must have capability to accept and display a progressive scan signal to use
PROGRESSIVE mode. Consult your TV operating instructions.

DVD/VCR DECK

DVD OUTPUT

S-VIDEO OUT

COMPONENT

VIDEO OUT

Y

P

B

P R

AUDIO OUT2

L

R

PB

PR

IN

L

Y

L

R

R

TV

IN

AUDIO

VIDEO

S-VIDEO
IN

From DECK’s

A/V OUTPUT

IN

(Connection)

Initial Setup

or

13

Connections (continued)

Audio Connections

Ready Checklist

Turn down the volume, then turn DECK, as well as other equipment to be connected,
off before proceeding with connection.
Do not block ventilation holes of any of the equipment and arrange them so that air can
circulate freely.
Read through the instructions before connecting other equipment.
Ensure that you observe the color coding when connecting audio and video cables.

■ Connecting Amplifier (2ch stereo system)

DVD/VCR DECK

AUDIO OUT2

L

Speaker

Amplifier

AUDIO IN

R L

R

Enjoying digital audio output from the digital audio output connector

Notes on audio output from the optical digital audio output connector

Disc
DVD

Sound recording format

Dolby Digital
Linear PCM

(48/96/192/44.1/88.2/

176.4 kHz 16/20/24bit)
DTS

Video CD
CD
MP3

WMA

*1 The type of audio output from the connector can be selected by the Settings for DVD

Operation. (See p. 54.)

*2 Sound having 96/192 kHz sampling is converted into 48 kHz sampling (or 88.2/176.4 kHz

sampling is converted into 44.1 kHz sampling) when it is output from the DECK’s optical digital
audio output connector.

MPEG 1
Linear PCM

MP3
WMA

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories
Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel)
sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit,
DVDs are recorded in 44.1 kHz/16 bit ~ 192 kHz/24 bit.

Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942, 5,956,674,
5,974,380, 5,978,762 and other world-wide patents issued and pending. “DTS” and “DTS Digital
Surround” are registered trademarks of Digital Theater Systems, Inc. Copyright 1996, 2000
Digital Theater Systems, Inc. All rights reserved.

Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Optical digital audio output from connector

Dolby Digital bitstream (1 - 5.1 ch)
or PCM (48 kHz sampling/16 bit only)*

Linear PCM (2 ch)
(48 kHz sampling/16 bit or 44.1 kHz sampling/

2

16 bit)*
Bitstream or PCM (48 kHz sampling/16 bit only)*
PCM (44.1 kHz sampling)
Linear PCM (44.1 kHz sampling)
Linear PCM (It depends on the MP3 file)

Linear PCM (It depends on the WMA file)

Speaker

1

1

14

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

■ Connecting Amplifier (5.1 ch Surround system)

Enjoy the powerful movie theater and hall-like sound available with multiple
channel audio found on DVDs by connecting an amplifier and speakers.
There are two types of connection, digital and analog.

A. Digital connection (DECK OPTICAL Digital Audio Output Connector)

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS
bitstream is output from the DECK OPTICAL Digital Audio Output Connector. When DECK
is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality
audio in your home. [An optical digital audio cable (optional) is required when an optional
Dolby Digital decoder or DTS decoder is used.]

B. Analog connection (5.1 ch Analog Audio Output Connector)

Connect an amplifier with multi-channel audio input terminals. This DECK can decode
Dolby Digital and DTS. There are no limitations on sampling frequency with this kind of
connection.

(Connection)

Initial Setup

Caution for optical digital audio output connector:

• When connecting an amplifier (with an Optical Digital Input Connector) which does not

contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital”
and “PCM” at “dts” of the Settings for DVD Operation “Audio Output” (see p. 54).
Otherwise, any attempt to play DVDs may cause such a high level of noise that it may
be harmful to your ears and damage your speakers.

• When a Dolby Digital/DTS decoder is connected, please select “Bitstream” at “dts” or

“Dolby Digital” of the Settings for DVD Operation “A udio Output”.
If “PCM” is selected, there will be stereo sound. (See p. 54.)

• Video CDs and CDs can be played as usual.

Note:

• Some DTS decoders which do not support DVD-DTS interface may not work properly with

DECK.

15

Initial Setup for Basic Connections (Ready to Play)

Before doing Initial Setup

Turn TV on.

1

See connections a RF Coaxial Cable Connection and b AV Cable Connection on page 12.

2

<RF Coaxial Cable Connection>
Set TV to channel 3.

<AV Cable Connection>

Set TV to VIDEO.

[DECK

3

• Go to “Initial Setup (Ready to Play).” (See below.)

[Cable Box

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel

• If you use a DSS Receiver, it must be turned off.

Initial Setup (Ready to Play)

Press VCR on remote for VCR mode.

1

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel
and clock set starts.

2

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to

• To change VCR’s output channel, please refer to “VCR’s Output Channel” on page 19.

➛➛

➛ TV]

➛➛

➛➛

➛ DECK

➛➛

in your time zone.

channel 3, try switching it to channel 4.

➛➛

➛ TV], [DSS

➛➛

➛➛

➛ DECK

➛➛

➛➛

➛ TV]

➛➛

16

Plugging the AC P o wer Plug into
an AC outlet

CH AUTO SET PROCEEDING
CANCEL : STOP

AUTO CLOCK SET
PROCEEDING

CANCEL : STOP

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Notes

• Function buttons are inoperative during Initial Setup.

• To remove a cassette during Auto Set, press EJECT on

the remote or STOP/EJECT twice on the DECK.
In this case, settings must be made manually. (See p. 18.)

• Depending on conditions, Auto Clock Set may take longer
than 30 minutes. If so, press STOP to stop setup and
perform settings manually. (See p. 18.)

Continued on next page...

*Important: If a remote control button does not work when pressed,

TH

press the VCR button on the remote and try the button again.

Settings are made automatically.
When setup is done, this screen appears.

3

6 / 8/ 20 03

VCR

SUN 2 : 20P

SETT I NG

: CH

AUTO CLOCK SET

COMPLETED

DST :

M

ON

10

If “AUTO CLOCK SET IS INCOMPLETE”
appears, manually set clock. See below.

AUTO CLOCK SET IS
I NCOM

PLETE

PLEASE SET CLOCK BY

ACT I ON KEY

PRESSING

Manual Clock Set

If Auto Clock Set was incomplete.

Press ACTION* on remote to display
CLOCK screen.

1

SET CLOCK

1 / /

- - - - - - - - -- - - - - - - -- - - - - -

SELE CT MONTH

SELECT :
SET :SET
EXIT

: ACT I ON

Press
set. In the same manner, select and set the

2

to select the month and SET to

:

DST : O

N

date, year, time, and DST (Da ylight Saving
Time).

SET CLOCK

6 / 8 / 2003 SUN 2: 2 0 PM

- - - - - - - - -- - - - - - - -- - - - - -

SET COMPLETE

SET : S
START :

Press ACTION to start clock and exit.

3

DST :

D

ET BACK :

ACT I O

N

ON

17

SELECT :
EXIT

: ACTION

SET : SET

MENU
SET UP VCR

SET CLOCK

SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

Reset Language, Channels, Clock, VCR’s

1

2

MENU

SET UP VCR

SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

SELECT :

: ACTION

SET:SET

EXIT

Press ACTION*

to display MENU.

Language

1) Press to select
language item.

MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT :
EXIT

: ACTION

2) Press SET repeatedly to
change language item as
shown below.

MENU
PREPARAR VCR
FIJAR RELOJ
FIJAR CANAL
SD CARD REPRODUCCION

LANGUE/LANGUAGE:ESPAÑOL

CANAL DE SALIDA : 3

ELEGIR :
SALIR

For Spanish

MENU
REGLAGE MAGNETOSCOPE
REGLAGE HORLOGE
REGLAGE CANAL
SD CARD LECTURE

LANGUAGE/IDIOMA:FRANÇAIS

CA SORTIE : 3

SEL. :
QUITTER

SET:SET

FIJAR : SET

: ACTION

REGLER:SET

: ACTION

For French

Channels

MENU
SET UP VCR
SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

SELECT :

:

CABLE

: ACT I ON

SET : SET

SET : SET

EXIT

: ACTION

2) Press to select
“ANTENNA,” then
press SET to set your
antenna system
(“TV” or “CABLE.”)

ANT

ENNA

AUTO86095 40692 0 0 4.8 2062.305 408.6208 Tm(O)Tj4.7902 0 0 4.83292305 408.6208 TS

SELECT :
EXIT

3) Press to select
“AUTO SET,” then

Clock

2) Press to select

“MANUAL,” and press SET.
(For Auto Clock Set, select
“AUTO CLOCK SET.”)

(“TIME ZONE ADJUST”

appears only when auto
clock is set.)

press SET.

• If you use a Cable Box,

set it to the PBS channel
in your time zone.

18

MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT :
EXIT

: ACTION

SET:SET

For English

3) Press ACTION to exit.

• After Channel Auto Set
is finished, Auto Clock
Set will be performed.

3) Press and to
select, then set the date,
time, and DST (Daylight
Saving Time).

4) Press ACTION to start
Clock and exit this
mode.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

C

HANNEL

08 ADDED

C

HANNEL

08 DELE T

ED

*Important: If a remote control button does not work

when pressed, press the VCR button
on the remote and try the button again.

Time Zone Adjust

(Only when Auto Clock is set.)

1) Press to select
“SET CLOCK,” and
press SET.

2) Press to select

“TIME ZONE ADJUST,”

and press SET to
subtract or add hour(s)
as necessary.

3) Press ACTION twice.

•“TIME ZONE ADJUST”
returns to “0” if clock is
set manually.

VCR’s Output
Channel

1) Press to select

“VCR’S OUTPUT CH.,”
and press SET.

MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT :

SET : SET

SET : SET

EXIT

: ACTION

2) Press SET.

I F YOU

3) Press ACTION .

After 3 seconds

MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT :
EXIT

: ACTION

• To Make Corrections,
repeat steps 1) ~ 3).

Add or Delete a Channel

To add channel:
Select channel with NUMBER keys

and press ADD/DLT.

To delete channel:
Select channel with CH / or

NUMBER keys and press ADD/DLT.

DST (Daylight Saving Time)

DECK auto adjusts clock for DST.
(p. 17.)

Spring (First Sunday in April)

➛➛

DST:ON

➛ Sets clock ahead one hour.

➛➛

Autumn (Last Sunday in October)

DST:ON

➛➛

➛ Turns clock back one hour.

➛➛

• If your area does not observe
Daylight Saving Time, select
DST:OFF.

• Keep these time changes in mind
when programming DECK for
timer recordings.

19

20

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

21

22

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]