Panasonic PV-D4753S User Manual

DVD/VCR DECK

Operating Instructions

(Connection)

Initial Setup

Model No.

Connections and Initial Setup Procedures are on pages 12 to 17.

PV-D4753S

Operation

Basic

Operation

VCR

Operation

DVD

MULTI FORMAT PLAYBACK

Ability to play back may depend on recording conditions.

As an ENERGY STAR Partner, Matsushita Electric Corporation
of America has determined that this product or product model
meets the ENERGY STAR guidelines for energy efficiency.

Please read these instructions carefully before attempting to connect, operate or adjust this
product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

D4753S P1-25.p65 2003/03/13, 11:321

®

*

®

LSQT0675A

Information

For Your

Important Safeguards and Precautions

FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY
AND OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON THE UNIT

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the
unit or in this manual. If necessary, have your
Electric Utility Service Company or Video Products
Dealer verify the power source in your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either
a polarized power cord plug (one blade is wider

than the other), or a three-wire grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you cannot

fully insert the plug, try reversing it. If it still will not fit,
have an electrician install the proper wall outlet. Do not
defeat the safety feature by tampering with the plug.

GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding

outlet. If necessary, have an electrician install the
proper outlet. Do not defeat the safety feature by
tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they

are not likely to have anything rest on them, roll

over them, or be in the way of walking traffic.

If an extension cord is used, make sure it also

has either a polarized or grounded plug and that

the cords can be securely connected.

Frayed cords, damaged plugs, and damaged or

cracked wire insulation are hazardous and should

be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire

hazards and should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat

generated during operation. If they are blocked,

heat build-up inside the unit can cause failures that

may result in a fire hazard or heat damage to

cassettes or discs.

For protection, follow these rules:

a. Never cover ventilation slots or the unit while in

use, or operate the unit when placed on a bed,
sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case

or rack, unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS

OR SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or

radiator, in direct sunlight, inside closed vehicles,

in high temperature [over 104°F (40°C)], or in over

75% humidity. If the unit is suddenly moved from

a cold place to a warm one, moisture may

condense in the unit and on the tape causing

damage. Never subject the unit to vibration,

impact, or place it so that the surface is tilted as

internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a sloping
surface.

• Do not place this unit on any support that is not
firm, level, and adequately strong.
The unit could fall causing serious
injury to a child or adult and
damage to the unit.

• An appliance and cart
combination should be moved
with care. Quick stops,
excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.

• Carefully follow all operating instructions and
use the manufacturer's recommended
accessories when operating this unit or
connecting it to any other equipment.

2

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded
so as to provide some protection against built up static
charges and voltage surges.
Section 810 of the National Electrical
Code, ANSI/NFPA 70 (in Canada,
part 1 of the Canadian Electrical
Code) provides information
with respect to proper grounding
of the mast and supporting
structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes and requirements for the grounding electrode.

2

KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS

An outside antenna system should be located well away from
power lines, electric light or power circuits and where it will never
come into contact with these power sources if it should happen
to fall. When installing an outside antenna, extreme care should
be taken to avoid touching power lines, circuits or other power
sources as this could be fatal. Because of the hazards involved,
antenna installation should be left to a professional.

If the unit has been in storage or moved to a new location,
refer first to the INSTALLATION section of these safeguards.

1

KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.

2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR

STRONG IMPACT, unplug the unit and have it inspected by a

qualified service technician before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or
before leaving the unit unused for extended periods of time,
disconnect all equipment from the power source as well as
the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE

• Never drop or push any object through openings in the unit.

• Avoid placing the unit directly above or below your TV set

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated
cloth to gently remove dust or debris. DO NOT USE cleaning
fluids, aerosols, or forced air that could over-spray, or seep
into the unit and cause electrical shock. Any substance such
as wax, adhesive tape, etc. may mar the cabinet surface.
Exposure to greasy, humid, or dusty areas may adversely
affect internal parts.

1 DO NOT SERVICE THIS PRODUCT YOURSELF

2 IF REPLACEMENT PARTS ARE REQUIRED

3

OUTDOOR ANTENNA INSTALLATION

NEC

- NATIONAL
ELECTRICAL CODE

ELECTRIC
SERVICE
EQUIPMENT

USING THE UNIT

if liquid has been spilled into the unit. Immediately unplug
the unit, and have it inspected by a service technician.
Fire and shock hazards can result from electrical shorts
caused by liquid contact inside.

Some internal parts carry hazardous voltages and contact
can cause electric shock or fire hazard.
Do not put any foreign object on the disc tray.

as this may cause electrical interference. Keep all magnets
away from electronic equipment.

SERVICE

If, after carefully following the detailed operating
instructions, this product does not operate properly, do not
attempt to open or remove covers, or make any
adjustments not described in the manual. Unplug the unit
and contact a qualified service technician.

Make sure the service technician uses only parts specified
by the manufacturer, or those having the same safety
characteristics as the original parts. The use of unauthorized
substitutes may result in fire, electric shock, or other hazards.

HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service
technician to conduct a thorough safety check as
described in the manufacturer’s service literature to ensure
that the unit is in safe operating condition.

GROUND
CLAMP

ANTENNA
LEAD IN
WIRE

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)

D4753S P1-25.p65 2003/03/13, 11:322

1

Safety Precautions/Mesures de sécurité

WARNING: To prevent fire or shock hazard, do not expose this

equipment to rain or moisture.

CAUTION: To prevent electric shock, match wide blade of plug to

wide slot, fully insert.

Avertissement: Afin de prévenir tout risque d’incendie ou de chocs

électriques, ne pas exposer cet appareil à la pluie ou
à une humidité excessive.

Attention: Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de la
prise et pousser jusqu’au fond.

This symbol warns the user that uninsulated voltage

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

within the unit may have sufficient magnitude to cause
electric shock.
Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.

This symbol alerts the user that important literature
concerning the operation and maintenance of this unit
has been included. Therefore, it should be read
carefully in order to avoid any problems.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE
YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER
OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when operated in a residential
environment. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, use the equipment in another location and/or utilize
an electrical outlet different from that used by the receiver.
If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the
booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting to
other devices.) Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.

FCC Warning: Any unauthorized changes or modifications to this equipment would void the user’s

authority to operate.

CAUTION:

LASER RADIATION
WHEN OPEN DO NOT
STARE INTO BEAM.

ATTENTION:

RAYONNEMENT
LASER EN CAS
D’OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.

(Inside of product)

Region Management Information:

This DECK is designed and manufactured to respond to the
Region Management Information that is recorded on a DVD
disc. If the Region number described on the DVD disc does
not correspond to the Region number of this DECK, this
DECK cannot play this disc.

● The Region number for this DECK is “1”.

● The Player will play DVD-Video marked with labels

containing “1” or “ALL”.

Example:

ALL

1

2

4

3

D4753S P1-25.p65 2003/03/13, 11:323

Before Using

Congratulations

on your purchase of one of the most
sophisticated and reliable products on the
market today. Used properly, it will bring you
years of enjoyment. Please fill in the
information below. The serial number is on the
tag located on the back of your DECK.

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.

• Serial No.

Accessories

Remote Control

LSSQ0377

To order accessories, call toll free
1-800-332-5368.

Loading the Batteries

PV-D4753S

Batteries 2 “AA”

RF Coaxial Cable
LSJA0372

Disc formats supported by this DECK

DECK can play back discs bearing any of the following
marks:

Logo Disc type

[Discs Played 8cm (3") or 12cm (5")]

DVD (DVD-Video)
DVD-R (DVD-Video formatted

discs [finalized])

DVD-Audio

Video CD
CD (CD-DA)

CD-R/CD-RW (CD-DA,Video CD
formatted discs [finalized])

WMA, MP3, JPEG

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• PAL discs (the audio on DVD-Audio can be played),

DVD-RAM, DVD-ROM, DVD-RW, DVD+RW, CD-ROM,
CDV, CD-G, CVD, SVCD, SACD, Divx Video Disc and
Photo-CD

Notes

• Do not use irregularly shaped discs (e.g. heart­shaped), as these can damage the unit.

• It may not be possible to play CD-R, CD-RW and
DVD-R in all cases due to the type of disc or
condition of the recording.

Disc Handling

Handling precautions

• Sticking a label on the disc may impair DVD-R playback.

• Do not attach sticker to discs. (Do not use discs with

exposed adhesive from tape or left over peeled-off
stickers.)

• Only hold disc by edges as shown below. Fingerprints,
dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning sprays, benzine, thinner,

static electricity prevention liquids, or any other solvent.

1) Open cover.

2) Insert
batteries as
marked.

3) Close cover.

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese

batteries.

4

D4753S P1-25.p65 2003/03/13, 11:324

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Disc tray

Disc

• Do not try to close disc tray when
disc is not properly placed.

To clean disc surface

With a soft, damp (water only) cloth, gently
wipe from the center hole to the outer edge
as shown below. (Wiping in a circular
pattern will scratch the surface.)

If disc is brought from a cold to a
warm environment, moisture may

form on the disc

Wipe away moisture with a soft, dry, lint-free cloth
before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Table of Contents

DVD / VCR

Important Safeguards and Precautions ............................ 2, 3

Before Using ............................................................................ 4

DECK & Cassette Information ........................................... 6 , 7

Location of Controls ....................................................... 8 ~ 10

Displays (On Screen Displays and Multi Function Display) .................... 11

Connections .................................................................. 12 ~ 15

Initial Setup for Basic Connections (Ready to Play) .......... 16, 17

VCR
Reset Language, Channels, Clock, VCR’s Output Channel ... 18, 19

Playback/ Record on a Tape........................................... 20, 21

DVD

Basic DVD Operation ...................................................... 22, 23

Timer Recording.............................................................. 24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System .................... 26, 27

Multi-Brand Control Feature ........................................... 28, 29

Tape Operation (Search System) ....................................... 30 ~ 32

Special VCR Features ..................................................... 33, 34

Copying Your Tapes (Dubbing) ......................................................... 35

(Connection)

Initial Setup

Operation

Basic

Operation

VCR

Disc Operation ............................................................... 36 ~ 41

DVD Operation using On-Screen Displays ................. 42 ~ 44

MP3/WMA/JPEG Playback Operation .......................... 45 ~ 47

DVD Lock Feature ................................................................. 48

Settings for DVD Operation .......................................... 49 ~ 53

Language Code List.............................................................. 54

DVD / VCR

Warning and Instruction Displays........................................ 55

Before Requesting Service............................................. 56, 57

Limited Warranty ............................................................. 58, 59

Customer Services Directory ............................................... 59

Spanish (Español) Quick Use Guide............................. 60~ 65

Index ................................................................................. 66, 67

D4753S P1-25.p65 2003/03/13, 11:325

Operation

DVD

Information

For Your

5

DECK & Cassette Information

Head Cleaning

Playing older or damaged tapes may eventually
cause video heads to become clogged.

Video Head Clog Sensor

During playback, this
screen appears if
clogging is detected.
To remove screen,
press PLAY on the
remote or DECK.

• Use “dry” type head cleaning cassette
only. (Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your
nearest servicenter by visiting our Web Site
(see p. 59).

V I D

EO HEADS MAY

N

EED

CLEAN I NG
PLEASE I NSERT HEAD
CLEAN I NG CASSETTE
OR REFER

TO

MANUAL

END

: PL

AY

Prevent Accidental Tape Erasure

Break off the tab to
prevent recording.

Record Tab

Screw driver

To record again

Cover the hole
with cellophane tape.

Record/ Playback Time

Only use tapes with the mark in this DECK.

Tape Speed

Setting

SP

(Standard Play)

LP

(Long Play)

SLP

(Super Long Play)

Type of Video Cassette

T160T120T60

1 Hour 2 Hours

2 Hours 4 Hours

2 Hours

40 Minutes

5 Hours

20 Minutes

3 Hours 6 Hours 8 Hours

Cleaning DECK

Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes
on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be
marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since
the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive,
antistatic cleaner and polisher.

Features for a Quality Picture (VCR)

Digital Auto Picture

Automatically controls the video output signal for less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for optimum picture quality.

Manual Tracking Control
(to reduce picture noise)

Use during Playback and Slow Motion mode to reduce picture noise.
Press CH (TRACKING) / on the remote control or on DECK until the picture clears up.
To return to Auto Tracking, press POWER off, then on again a few seconds later.

R

R

R

R

V-Lock Control (to reduce picture jitter)
In Still mode, CH (TRACKING) / operate as a V-Lock control.

6

D4753S P1-25.p65 2003/03/13, 11:326

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

R

R

R

R

Specifications

Power Source: 120 V AC, 60 Hz
Power Consumption: Power On: Approx. 32 watts, Power Off: Approx. 4 watts

Video Signal: EIA Standard NTSC color
Video Recording System: 4 rotary heads helical scanning system

Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound)
Tuner:
Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output
Input Terminal: Audio/Video Line Input (Front)
Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)

Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity: 10 % ~ 75 %
Weight: 4.9 kg (10.8 lbs).
Dimensions: 430 (W) x 95.5 (H) x 344 (D) mm

Discs Played
(1) DVD-Video Disc 5” (12 cm) single-sided single-layer

DVD-Audio Disc 5” (12 cm) single-sided double-layer

(2) Compact Disc 5” (12 cm) disc

(CD-DA, Video CD) 3” (8 cm) disc
(CD-R/CD-RW, MP3, WMA, JPEG)

Digital Audio Output: Digital Optical Connector
Pickup: Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)

Note: • Designs and specifications are subject to change without notice.

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Audio Output 2 (L), (R)

16-15/16” (W) x 3-12/16” (H) x 13-9/16” (D) inch

5” (12 cm) double-sided double-layer (one layer per side)
3” (8 cm) single-sided single-layer
3” (8 cm) single-sided double-layer
3” (8 cm) double-sided double-layer (one layer per side)

Laser power: CLASS II

Definition of Terms (DVD)

Angle: Some DVD discs feature scenes simultaneously shot from different angles.

Chapter Number:Titles are subdivided into numbered sections. You can quickly search for

DVD: A high-density optical disc on which high-quality pictures and sound have

Playback Control:With Video CD (version 2.0), scenes or information may be selected for

Subtitles: Written dialogue which appears at the bottom of the screen.
Time Number: The elapsed play time from the start of a disc or title. Use to quickly find

Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.
Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks

Video CD: CD containing picture and sound with same quality level as video tape.

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093,
licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by method claims of
certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

The ANGLE button can be used to view the scene from different angles.
(ANGLE Indicator lights on DECK when a scene recorded at different
angles is detected.)

a favorite scene using these numbers.

been digitally recorded. DVD incorporates new video compression
technology (MPEG II) and high-density recording technology which allow
entire movies to be recorded with incredible playback quality.

viewing or listening from an interactive menu that appears on the TV screen.

scenes. (May not work with some discs.)

to be quickly located.

This DECK also supports Video CDs with playback control (version 2.0).

(Connection)

Initial Setup

7

D4753S P1-25.p65 2003/03/13, 11:327

Location of Controls

Remote Control

EJECT /

OPEN / CLOSE

pp. 20,

22

POWER

VCR mode

p. 28

DSS / CABLE mode

p. 28

PLAY

pp. 20,

22

REWIND /

SLOW-

pp. 20,

VCR/TV

p. 21

NUMBER keys

RETURN /

pp

. 22,

ACTION

pp. 18

SKIP
SKIP

p

. 23

TITLE

p

. 38

23

30

, 49

SEARCH

SEARCH

Bold: VCR Function

Italic

:

DVD Function

Bold Italic:VCR and DVD Functions

Normal: Others

DISPLAY

p. 11,

42

TV mode

p. 28

DVD mode

p. 28

INPUT

p. 35

FAST FORWARD /

SEARCH / SLOW+

/

ADD/DELETE /

Virtual Surround Sound (V.S.S.)

PAUSE /

pp. 19,

PROGRAM

pp. 20,

STILL

pp. 20,

STOP

pp. 20,

CLEAR

39, 48

ENTER

pp.

23,

28

p. 24

SELECT

MENU

p

. 38

23

23

22

/

SET

ANGLE

p

. 37

AUDIO

(SAP / Hi-Fi)

pp. 27,

36

VOLUME

p. 28

+

/

-

COUNTER
RESET

p. 32

SPEED

p. 21,

D4753S P1-25.p65 2003/03/13, 11:328

/

PAGE

41

EJECT button: When this button is pressed in VCR mode, the tape is ejected.

8

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

This button is inoperative if pressed during recording.
If pressed in DVD mode, the disc tray opens or closes.

SUB TITLE

ZOOM

COMMERCIAL SKIP

ZERO SEARCH

pp. 31, 32

CHANNEL

TRACKING

/

V-LOCK

pp. 6, 21

/

TAPE POSITION

VOLUME ADJUST

p. 34,

RECORD

p

. 36

p

. 37

40

p. 21

/

/

Front View of DECK

Front View of DECK

Bold: VCR Function

Italic

:

DVD Function

:

Bold Italic

Normal: Others

STOP/EJECT

p. 20

FAST FORWARD/SEARCH

p. 20

PLAY

p. 20

REWIND/SEARCH

p. 20

Remote
Sensor

POWER

Audio/Video
Input Connector 2
(LINE 2)

CHANNEL /
TRACKING/V-LOCK

pp. 6, 21

REC

p. 21

VCR and DVD Functions

p. 35

Reset All Memory Functions

If the disc cannot be removed...

First, unplug DECK. Then, prepare a rigid
wire (e.g. an extended paper clip) and,
applying moderate force, insert it straight
into the hole at the base of the tray.
The tray will eject a little. Now, pull the tray
all the way out and remove the disc.

Over 2 inches

Cassette
Compartment

Multi Function

Display

p. 11

Disc Tray

OPEN/CLOSE

PROGRESSIVE

PAUSE

SKIP
SKIP

PLAY

STOP

p.

22

p.

10

p.

23

p.

23

p.

22

p.

22

(Connection)

Initial Setup

Use when moving DECK to new location, or if a mistake was made in the Initial
Setup section (return to Factory Setting).

• Make sure a tape is not inserted in the DECK.

Turn DECK Power on.

1

Press and hold both VCR PLAY

2

21 21

D4753S P1-25.p65 2003/03/13, 11:329

and CHANNEL
more than 5 seconds.

• The power shuts off.
Do “Initial Setup (Ready to Play)”

3

on page 16.

on the DECK for

9

Location of Controls (continued)

Rear View of DECK

AC Power Plug

• While plugged into an AC outlet,
this DECK consumes 4 W of
electrical power in off mode.

Component Video Output
Connector (Y, PB, PR) (DVD Only)

p.

13

Bold: VCR Function

Bold Italic:VCR and DVD Functions

VHF/UHF Antenna Output Terminal
p.12

VHF/UHF Antenna Input Terminal
p. 12

Video Output
Connector

p.

12

Italic:DVD Function

Video Input
Connector
p. 35

5.1ch Analog Audio Output
Connector (CENTER, SUB WOOFER,
SURROUND L/R, FRONT L/R)

p.

(DVD Only)

Optical Digital Audio
Output Connector
(DVD Only)

p.

15

15

S-Video Out
Connector
(DVD Only)

pp.

10, 13

••

Audio Output 2
Connector (L/R)

p.

13

Audio Output 1

•

Audio Input
Connector (L/R)

p.

35

Connector (L/R)

p.

12

The following table shows the status of the output jacks when in VCR or DVD mode.

VCR

DVD

Video Output
Audio Out 1
Audio Out 2

YES
YES

Component
Video Output

N/A

S-VIDEO OUT

N/A

YES

• PROG functions on the remote are not available when using Component Video Output

Note

and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press
PROG.

To enjoy PROGRESSIVE SCAN video

(1). Connect

(See p. 13.)

(2). When the PROGRESSIVE button is pressed, the ON lamp lights up (see p. 9) and the

PROGRESSIVE SCAN signal is output from the

Notes

• The PROGRESSIVE button can be operated when the DECK is in DVD function mode.

• The screen may shift off-center when using progressive output. Please adjust the screen

position if this occurs. (Refer to your TV manual.)

• The DECK outputs video signals (not PROGRESSIVE SCAN) from the “VIDEO OUT” and
“S-VIDEO OUT” terminals when the ON lamp is lit.

10

D4753S P1-25.p65 2003/03/13, 11:3210

Component Video Output

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

to the component video input terminals of a television.

Component Video Output Connector

.

Displays (On Screen & Multi Function)

DIGIT

On Screen Displays (VCR)

Function & Channel Displays

CH 0 8

When a function button
is pressed, e.g. PLAY,
or you change
channels, a 5-second
display appears.

VCR Status & Clock Displays
To display or remove
overlay at right,

➛➛

➛ press DISPLAY.

➛➛

Rec Time Remaining
(OTR mode only,
see p. 21.)

Multi Function Display

VCR mode Indicator

Lights up when
DECK is VCR mode.

Timer Indicator

Lights up when
DECK is set for
Timer Recording,
or when One
Touch Recording
(OTR) is used.
Flashes when
Timer Recording is
set, but a tape has
not been inserted
into DECK and
when a power
interruption occurs
during Timer
Programming.

DTS Indicator

Lights up when DTS
formatted DVD is played.
(DVD only)

Dolby Digital
Indicator

Lights up when “Dolby Digital”
formatted DVD is played.
(DVD only)

Tape Indicator

Lights up when a tape
is inserted.

VCR

TIMER REC

DIGIT

Hi-Fi Indicator

Lights up when
Hi-Fi audio is
monitored in Play
mode.

Function Status

Broadcast Audio
Being Received
(See p. 26.)

VCR REC Indicator

Lights up during
recording.

Hi - Fi

AL

Blank Tape/ No Video Signal
Indications

Whenever a blank section of a tape
comes up in Play mode, or when the
selected channel has no broadcast
signal with Weak Signal Display
Feature (p. 33) set to OFF, the TV
screen will turn solid blue.

Current Time

REC

1 2 : 0 0A

0 : 25

STER

EO
SAP
M

ONO

M

-0 : 1 2 : 3 4

CH 02

SP

Channel

Counter

Tape Speed
(See p. 6.)

DISC Indicator

Lights up when a
disc is inserted.

DVD mode Indicator

Lights up when
DECK is DVD mode.

CD/MP3/WMA
Indicator

CD : Lights when a

Video or Audio
CD is inserted
or JPEG file is
played.

MP3/WMA :

Lights when an
MP3 or WMA

CD

AM
PM

MP3

ANGLE

DVD

WMA

file is played.

ANGLE Indicator

AM/PM
Indicator

Lights up when a
scene recorded at
different angles is
detected.
(See p. 37.)
(DVD only).

Clock/ Status/ Channel/ Speed Display

Displays the current time. Briefly displays DECK
status when a function button is pressed. Briefly
displays the channel number, or “L1” or “L2”
when a channel or line input is selected. Briefly
displays the recording speed when SPEED is
pressed.

(Connection)

Initial Setup

11

D4753S P1-25.p65 2003/03/13, 11:3211

Connections

Basic Connections

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

• Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable
(not supplied) as shown in the figure below.

■ ■

■ ■

■ DSS Receiver DECK TV

■ ■

■ ■

■ DECK TV

■ ■

Antenna or Cable

■ Cable Box DECK TV

■ ■

b

DSS
Receiver

IN

IN

OUT

or

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VIDEO

L

AUDIO

R

WARNING

When using “Nut type” RF coaxial cables, tighten with
fingers only. Overtightening may damage terminals.

VHF/UHF

OUT TO TV

IN

OUT

Cable Box

1 Disconnect antenna or cable from TV

and connect to DECK.

2 Connect DECK to TV with RF Coaxial Cable.

RF COAXIAL CABLE

a

TV

AUDIO IN

R

(supplied)

VIDEO

IN

L

b

AV CABLE

VHF/
UHF

(not supplied)

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the
NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.

12

D4753S P1-25.p65 2003/03/13, 11:3212

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Other Connections

■ ■

■ With a Cable Box (DECK

■ ■

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VHF/UHF

OUT TO TV

■■

■

Connect With Two Cable Boxes

■■

ANT or CATV

Cable Box

Cable Box TV)

OUTIN

DVD/VCR DECK

ANT

or

CATV

Cable Box

OUT

IN

2-Way Splitter

OUT 1

OUT 2

OUT

Cable Box

OUTIN

IN 1

IN FROM ANT.

VHF/UHF
OUT TO TV

A/B Switch

VHF/
UHF

IN 2IN 1

• view any
(including

• use Remote

• record and view

TV

AUDIO

VIDEO

scrambled)
channel.

Control to select
channels without
using Multi-brand
control feature.

both scrambled
and unscrambled
channels if
additional
equipment is
added.
This connection
requires: two
converter boxes,
an A/B switch,
and a 2-way
splitter.

TV

IN

OUT

R

AUDIO

L

VIDEO

IN

OUT

R
L

VHF/
UHF

You CannotYou Can

• record
scrambled
channels.

You CannotYou Can

• view a channel
other than the
one selected
for any type of
recording.

• do a Timer
recording of a
channel unless
you select it on
the Cable Box.

Connections For DVD Only (enjoying higher picture quality)

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT

1

or S-VIDEO mode).
If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.

2

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to
S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

3

Notes

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV,
and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only
from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT
Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

• TV must have capability to accept and display a progressive scan signal to use
PROGRESSIVE mode. Consult your TV operating instructions.

DVD/VCR DECK

DVD OUTPUT

S-VIDEO OUT

COMPONENT

VIDEO OUT

Y

P

B

P R

AUDIO OUT2

L

R

PB

PR

IN

L

Y

L

R

R

TV

IN

AUDIO

VIDEO

S-VIDEO
IN

From DECK’s

A/V OUTPUT

IN

(Connection)

Initial Setup

or

D4753S P1-25.p65 2003/03/13, 11:3213

13

Connections (continued)

Audio Connections

Ready Checklist

Turn down the volume, then turn DECK, as well as other equipment to be connected,
off before proceeding with connection.
Do not block ventilation holes of any of the equipment and arrange them so that air can
circulate freely.
Read through the instructions before connecting other equipment.
Ensure that you observe the color coding when connecting audio and video cables.

■ Connecting Amplifier (2ch stereo system)

DVD/VCR DECK

AUDIO OUT2

L

Speaker

Amplifier

AUDIO IN

R L

R

Enjoying digital audio output from the digital audio output connector

Notes on audio output from the optical digital audio output connector

Disc
DVD

Sound recording format

Dolby Digital

Linear PCM
(48/96/192/44.1/88.2/

176.4 kHz 16/20/24bit)
DTS

Video CD
CD
MP3

WMA

*1 The type of audio output from the connector can be selected by the Settings for DVD

Operation. (See p. 50.)

*2 Sound having 96/192 kHz sampling is converted into 48 kHz sampling (or 88.2/176.4 kHz

sampling is converted into 44.1 kHz sampling) when it is output from the DECK’s optical digital
audio output connector.

MPEG 1
Linear PCM

MP3
WMA

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories
Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel)
sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit,
DVDs are recorded in 44.1 kHz/16 bit ~ 192 kHz/24 bit.

Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942, 5,956,674,
5,974,380, 5,978,762 and other world-wide patents issued and pending. “DTS” and “DTS Digital
Surround” are registered trademarks of Digital Theater Systems, Inc. Copyright 1996, 2000
Digital Theater Systems, Inc. All rights reserved.

Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Optical digital audio output from connector

Dolby Digital bitstream (1-5.1 ch)
or PCM (48 kHz sampling/16 bit only)*

Linear PCM (2 ch)
(48 kHz sampling/16 bit or 44.1 kHz sampling/

2

16 bit)*
Bitstream or PCM (48 kHz sampling/16 bit only)*
PCM (44.1 kHz sampling)
Linear PCM (44.1 kHz sampling)
Linear PCM (It depends on the MP3 file)

Linear PCM (It depends on the WMA file)

Speaker

1

1

14

D4753S P1-25.p65 2003/03/13, 11:3214

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

■ Connecting Amplifier (5.1 ch Surround system)

Enjoy the powerful movie theater and hall-like sound available with multiple
channel audio found on DVDs by connecting an amplifier and speakers.
There are two types of connection, digital and analog.

A. Digital connection (DECK OPTICAL Digital Audio Output Connector)

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS
bitstream is output from the DECK OPTICAL Digital Audio Output Connector. When DECK
is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality
audio in your home. [An optical digital audio cable (optional) is required when an optional
Dolby Digital decoder or DTS decoder is used.]

B. Analog connection (5.1 ch Analog Audio Output Connector)

Connect an amplifier with multi-channel audio input terminals. This DECK can decode
Dolby Digital and DTS. There are no limitations on sampling frequency with this kind of
connection.

Notes on connecting an optical
digital audio cable (optional)

• Firmly connect the cable to the
connector.

Surround
Speaker

[5.1 ch Surround system]

Center
Speaker

Surround
Speaker

(Connection)

Initial Setup

Front
Speaker

Front
Speaker

Amplifier

B. Analog connection

To multi-channel audio

DVD/VCR DECK (Rear)

A. Digital connection

input terminals

Decoder with Dolby Digital
/DTS processing

Subwoofer

Optical Digital Audio
Cable (optional)

To Optical Digital Audio
Input Connector

Caution for optical digital audio output connector:

• When connecting an amplifier (with an Optical Digital Input Connector) which does not
contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital”
and “PCM” at “dts” of the Settings for DVD Operation “Audio Output” (see p. 50).
Otherwise, any attempt to play DVDs may cause such a high level of noise that it may
be harmful to your ears and damage your speakers.

• When a Dolby Digital/DTS decoder is connected, please select “Bitstream” at “dts” or
“Dolby Digital” of the Settings for DVD Operation “Audio Output”.
If “PCM” is selected, there will be stereo sound. (See p. 50.)

• Video CDs and CDs can be played as usual.

Note:

• Some DTS decoders which do not support DVD-DTS interface may not work properly with
DECK.

15

D4753S P1-25.p65 2003/03/13, 11:3215

Initial Setup for Basic Connections (Ready to Play)

Before doing Initial Setup

Turn TV on.

1

See connections a RF Coaxial Cable Connection and b AV Cable Connection on page 12.

2

<RF Coaxial Cable Connection>
Set TV to channel 3.

<AV Cable Connection>

Set TV to VIDEO.

[DECK

3

• Go to “Initial Setup (Ready to Play).” (See below.)

[Cable Box

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel

• If you use a DSS Receiver, it must be turned off.

Initial Setup (Ready to Play)

Press VCR on remote for VCR mode.

1

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel
and clock set starts.

2

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to

• To change VCR’s output channel, please refer to “VCR’s Output Channel” on page 19.

➛➛

➛ TV]

➛➛

➛➛

➛ DECK

➛➛

in your time zone.

channel 3, try switching it to channel 4.

➛➛

➛ TV], [DSS

➛➛

➛➛

➛ DECK

➛➛

➛➛

➛ TV]

➛➛

CH AUTO SET PROCEEDING

CANCEL : STOP

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

16

D4753S P1-25.p65 2003/03/13, 11:3216

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Plugging the AC Power Plug into
an AC outlet.

Notes

• Function buttons are inoperative during Initial Setup.

• To remove a cassette during Auto Set, press EJECT on

the remote or STOP/EJECT twice on the DECK.
In this case, settings must be made manually. (See p. 18.)

• Depending on conditions, Auto Clock Set may take longer
than 30 minutes. If so, press STOP to stop setup and
perform settings manually. (See p. 18.)

Continued on next page...

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

EJECT

VCR

ACTION

SELECT

SET

Settings are made automatically.
When setup is done, this screen appears.

3

6 / 8/ 20 03

SUN 2 : 20P

SETT I NG

: CH

AUTO CLOCK SET

COMPLETED

DST :

M

ON

10

If “AUTO CLOCK SET IS INCOMPLETE”
appears, manually set clock. See below.

AUTO CLOCK SET IS
I NCOM

PLETE

PLEASE SET CLOCK BY

ACT I ON KEY

PRESSING

Manual Clock Set

If Auto Clock Set was incomplete.

Press ACTION* on remote to display
CLOCK screen.

1

(Connection)

Initial Setup

STOP

D4753S P1-25.p65 2003/03/13, 11:3217

SET CLOCK

1 / /

- - - - - - - - -- - - - - - - -- - - - - -

SELE CT MONTH

SELECT :
SET :SET
EXIT

: ACT I ON

Press
set. In the same manner, select and set the

2

to select the month and SET to

:

DST : O

N

date, year, time, and DST (Daylight Saving
Time).

SET CLOCK

6 / 8 / 2003 SUN 2: 2 0 PM

- - - - - - - - -- - - - - - - -- - - - - -

SET COMPLETE

SET : S
START :

Press ACTION to start clock and exit.

3

DST :

D

ET BACK :

ACT I O

N

ON

17

Reset Language, Channels, Clock, VCR’s O

AUTO CLOCK SET

MANUNU

AL

T I M

E ZONE AD

JUS

T :

0

SELECT :

SET :

SET

EXIT

: ACT I ON

SET CLOCK

DST :

ON

6 / 8 / 2003 SUN 12: 0 0 PM

SELECT HOUROUR

- - - - - - - - -- - - - - - - -- - - - - -

SET CLOCK

SELE

CT :

SET

:

SET BACK :

EXIT

: ACT I ON

SELECT :
EXIT

: ACTION

SET : SET

MENU
SET UP VCR

SET CLOCK

SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

1

2

MENU

SET UP VCR

SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

SELECT :

: ACTION

SET:SET

EXIT

Press ACTION*

to display MENU.

Language

1) Press to select

language item.

MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT :
EXIT

: ACTION

2) Press SET repeatedly to

change language item as
shown below.

MENU
PREPARAR VCR
FIJAR RELOJ
FIJAR CANAL

LANGUE/LANGUAGE:ESPAÑOL

CANAL DE SALIDA : 3

ELEGIR :
SALIR

For Spanish

MENU
REGLAGE MAGNETOSCOPE
REGLAGE HORLOGE
REGLAGE CANAL

LANGUAGE/IDIOMA:FRANÇAIS

CA SORTIE : 3

SEL. :
QUITTER

SET:SET

FIJAR : SET

: ACTION

REGLER:SET

: ACTION

For French

➡

➡

• PROGRAM functions are not available
when using COMPONENT Video Output
and S-VIDEO OUT. Please set TV to
either RF INPUT or VIDEO INPUT, and
then press PROGRAM.

Channels

1) Press to select

“SET UP CHANNEL,”
and press SET.

MENU
SET UP VCR
SET CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

SELECT :

:

CABLE

: ACT I ON

SET : SET

NNE

L

SPLAY : OFF

SET : SET

EXIT

: ACTION

2) Press to select

“ANTENNA,” then
press SET to set your
antenna system
(“TV” or “CABLE.”)

SET UP CHA

ANT

ENNA

AUTO SET
WEAK

S I GNAL D I

ABLE / DSS BOX SET UP

C
VCR Plus+ CH SET UP

SELECT :
EXIT

3) Press to select

“AUTO SET,” then
press SET.

• If you use a Cable Box,
set it to the PBS channel
in your time zone.

Clock

1) Press to select

“SET CLOCK,” and

press SET.

2) Press to select
“MANUAL,” and press SET.
(For Auto Clock Set, select
“AUTO CLOCK SET.”)

(“TIME ZONE ADJUST”

appears only when auto
clock is set.)

MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT :
EXIT

: ACTION

SET:SET

For English

3) Press ACTION to exit.

18

D4753S P1-25.p65 2003/03/13, 11:3218

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

CH AUTO SET PROCEEDING

CANCEL : STOP

• After Channel Auto Set
is finished, Auto Clock
Set will be performed.

3) Press and to

select, then set the date,
time, and DST (Daylight
Saving Time).

4) Press ACTION to start

Clock and exit this
mode.

C

HANNEL

08 ADDED

C

HANNEL

08 DELE T

ED

*Important: If a remote control button does not work

when pressed, press the VCR button
on the remote and try the button again.

POWER

VCR

Time Zone Adjust

(Only when Auto Clock is set.)

1) Press to select

“SET CLOCK,” and
press SET.

MENU
SET UP VCR

SET CLOCK

SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

SELECT :
EXIT

: ACTION

2) Press to select

“TIME ZONE ADJUST,”

AUTO CLOCK SET
MANU

T I M

SELECT :
EXIT

: ACT I ON

and press SET to
subtract or add hour(s)
as necessary.

3) Press ACTION twice.

•“TIME ZONE ADJUST”
returns to “0” if clock is
set manually.

SET : SET

SET CLOCK

AL

E ZONE AD

JUS

SET : SET

T :

0

VCR’s Output
Channel

1) Press to select

“VCR’S OUTPUT CH.,”
and press SET.

MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT :
EXIT

: ACTION

2) Press SET.

I F YOU PRESS
KEY, VCR’
SW I

TCHES TO

3) Press ACTION.

PLEASE TUNE YOUR TV TO
CH 4.

➡

After 3 seconds

MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:4

SELECT :
EXIT

: ACTION

• To Make Corrections,
repeat steps 1) ~ 3).

SET : SET

ACT I O

S OUTPUT CH

CH 4.

SET : SET

N

NUMBER
keys

ACTION
ADD/DLT

SELECT

SET

CH /

Add or Delete a Channel

To add channel:
Select channel with NUMBER keys

and press ADD/DLT.

To delete channel:
Select channel with CH / or

NUMBER keys and press ADD/DLT.

DST (Daylight Saving Time)

DECK auto adjusts clock for DST.
(p. 17.)

Spring (First Sunday in April)

➛➛

DST:ON

➛ Sets clock ahead one hour.

➛➛

Autumn (Last Sunday in October)

DST:ON

➛➛

➛ Turns clock back one hour.

➛➛

Operation

Basic

• If your area does not observe
Daylight Saving Time, select
DST:OFF.

• Keep these time changes in mind
when programming DECK for
timer recordings.

19

D4753S P1-25.p65 2003/03/13, 11:3219

Playback/ Record on a Tape

Ready Checklist

All connections are made. (pp. 12 ~ 15)
TV and DECK are plugged in.
TV is on and tuned to CH 3, 4, or VIDEO.
Remote is in VCR mode. (Press VCR.)

Playback a Tape

Insert a tape.

1

• DECK power comes on. If Auto VCR/TV (see
p. 32) is set to “OFF,” press VCR/TV on the
remote to be VCR mode.

Press PLAY* to play a tape.

2

• If tape has no rec. tab (p. 6), auto play begins.

Special Features During Play

Forward/Reverse Scene Search

➛➛

➛ Press FF/SLOW+ or REW/SLOW-.

➛➛
➛➛

➛ Press PLAY to release.

➛➛

After search has begun, each additional press of
FF or REW changes speed as shown below.

[SLP] : Approx. 21X
[LP] : Approx. 9X
[SP] : Approx. 7X

If at 21X, 9X, or 7X speed the picture is
interrupted, change speed to 9X, 7X, or 3X.

Notes

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary

depending on current tape position.

Still (Freeze) Picture

➛➛

➛ Press PAUSE/STILL.

➛➛
➛➛

➛ Press PLAY to release.

➛➛

Frame by Frame Picture

➛➛

➛ Press PAUSE/STILL in Still mode.

➛➛
➛➛

➛ Press PLAY to release.

➛➛

Slow Motion Picture

➛➛

➛ Press FF/SLOW+ (increase speed) or

➛➛

REW/SLOW- (decrease speed) in Still
mode.

➛➛

➛ Press PLAY to release.

➛➛

↔ Approx. 9X
↔ Approx. 7X
↔ Approx. 3X

EJECT

VCR

REW/SLOW­VCR/TV
STOP

Notes

• These features work best in SP or SLP mode.

• The sound will be muted.

• To reduce picture noise, see “Manual Tracking
Control” on page 6.

• After DECK is in Still or Slow mode for 3 minutes,

it will switch to Stop mode automatically to
protect the tape and the video head.

DVD

PLAY

FF/SLOW+
PAUSE/

STILL

CH /
REC
SPEED

Playback using DECK buttons

21

Press PLAY.

Insert a tape.

Press STOP to stop a tape.

3

Press REW/SLOW- or FF/SLOW+ in Stop
mode to rewind or fast forward a tape.

Press EJECT on remote, or STOP/EJECT

on DECK to eject a tape.

20

D4753S P1-25.p65 2003/03/13, 11:3220

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Multi Function Display

Press STOP/EJECT to stop
and/ or eject a tape.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Record on a Tape

Insert a tape with a record tab (p. 6).

1

• DECK power comes on. If Auto VCR/TV (see p. 32)
is set to “OFF,” press VCR/TV on the remote to be
VCR mode.

Press CH , or NUMBER keys

2

to select the channel.

• For “LINE” input, see p. 35.

• If channel is over 100, press 100 key then press

the remaining 2 digits.

Press SPEED

to select the record speed (p. 6).

3

SP = Standard Play LP = Long Play
SLP = Super Long Play

• Speed appears on-screen and on Multi Function Display.

Press REC

to start recording.

4

(The VCR REC indicator lights up on Multi Function
Display),

• To edit out unwanted scenes, press PAUSE/STILL
to pause, and again to resume recording.

• You cannot view another channel during recording.

Press STOP

to stop recording.

5

One Touch Recording (recording in progress),

➛➛

➛ press REC repeatedly to set the recording length

➛➛
➛➛

➛ (30 min. ~ 4 hours).

➛➛

• DECK shuts off after the preset record length.

Record one station, watch another,

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at TV (recording continues).

➛➛

Select Channels at DECK (In STOP or
REC. PAUSE mode),

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at DECK.

➛➛

Play a disc while recording a tape.

➛➛

➛ insert a disc during recording,

➛➛
➛➛

➛ press

➛➛

Notes

• It is not possible to record from DVD/ Video
CD/ CD to VHS tape using DECK.

• Watching one channel and recording another
is not possible when using Cable Box or
DSS Receiver.

• After 5 minutes in Pause mode, DECK stops to
protect a tape and video heads.

DVD

, and then press

PLAY

.

This video recorder, equipped with HQ
(High Quality) system, is compatible
with existing VHS equipment. Only use
tapes with the mark. Only tapes
tested and inspected for use in 2, 4, 6,
and 8 hour machines are
recommended.

Note

Remove loose or peeling
labels from tapes to prevent
tape jam.

Normal Rec

0:30 1:00

1:302:003:004:00

Record using DECK buttons

Insert a tape.

1

Select

2

Channel.

Multi Function Display

Press STOP/EJECT to stop.

4

Press REC
to start
recording.

Operation

Basic

21

D4753S P1-25.p65 2003/03/13, 11:3221

Basic DVD Operation

Ready Checklist

All connections are made. (pp. 12 ~ 15)
DECK is plugged in.
If DECK is connected to an audio amplifier,

turn the stereo system’s power on.

POWER

PLAY

REW/
SLOW-

STOP

NUMBER

keys

RETURN

SKIP
SELECT

SET

TITLE

OPEN/
CLOSE

DVD

FF/
SLOW+

PAUSE/
STILL

VSS

SKIP

MENU

10

1

2

3

4

If an interactive DVD*1 or
a Video CD with playback
control*2 is used and TITLE
MENU appears, go to step 5.

5

Operation using DECK buttons

Press

3, 7

1

Press
POWER.

Insert a disc.

3

*1Interactive DVD...

May include multiple camera angles,
stories, etc.

*2Video CD with playback control...

Particular scenes or information can be
interactively selected from a menu that
appears on the screen.

22

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

OPEN/CLOSE.

4

Press PLAY.

6

Press STOP.

Using NUMBER keys starts playing automatically.

The number of available titles varies with each disc.

<Input

Press
menu screen.

• SKIP function not available with all discs.

To return to menu (play stops)

Press

DVD-Audio)

Press

6
7

Press

POWER*

Press

DVD

• If a disc is already inserted, go to step 4.
(Depending on the disc, playback may
start automatically.)

Press

OPEN/CLOSE

and then place a disc into the disc tray.

Press

PLAY

Disc tray closes automatically.

CLOSE

READING

<Example2>

Example>

SKIP

| or | to go to next or previous

Please refer to disc jacket for operation information.

TITLE, MENU,

RETURN

Press

STOP

Press

OPEN/CLOSE

on the remote or DECK.

to select DVD mode.

,

• Hold disc by its edges
only (p. 4) with printed
side up and use guides to

1

place into tray.

2

Use 3” (8 cm)

1

or 5” (12 cm) disc.

2

to start playing.

• You may also close tray by

pressing

• Data reading time differs with
each disc.

1 digit number 1 ••• 1
2 digit number 12 ••• 10 1 2
3 digit number 123 •••100 1 2 3

or

. (Video CD)

to stop playing.

OPEN/CLOSE

<Example1>

T I TLE MENU

Cas t l es

Dogs

Love

r

s

Press or

NUMBER keys

below) to select title,
and press

PLAY

•“Pressing
is not necessary when
using

RETURN

to eject the disc.

SET

or

to start playing.

SET

or

NUMBER keys.

. (DVD-Video/

.

i r

B

(see

PLAY

ds

”

D4753S P1-25.p65 2003/03/13, 11:3222

*Important: If a remote control button does not work when pressed,

VSS OFF (default)

VSS1

VSS3

VSS2

press the DVD button on the remote and try the button again.

■ Forward/Reverse Scene Search

Press

FF/SLOW+

or

REW/SLOW-

during play.

PLAY

Press

• Starting forward/reverse search during play
started from menu on Video CDs may recall menu.

• Search speed, slow at first, increases with each
additional press of the button up to 5 levels.

to release.

■ Forward/Reverse Chapter/Track Skip

Press

SKIP

| or |

SKIP

during play.
Each press skips a chapter (DVD-Video) or
track (DVD-Audio/Video CD/CD).

• Pressing |

chapter/track returns to the start of that
chapter/track. Each additional press skips
back one chapter/track.

• Pressing

from menu on Video CDs may recall menu.

Chapter/Track Chapter/Track Chapter/TrackChapter/Track

Reverse Skip Forward Skip

SKIP

once midway through a

SKIP

| or | during play started

Current playback position

■ Still Picture or Pause

Press

PAUSE/STILL
PLAY

Press

• DVD/Video CD : DECK will enter still picture mode.

• CD : DECK will enter pause mode.

to release.

during play.

■ Frame by Frame Picture

(DVD/Video CD)
Press

PAUSE/STILL

PLAY

Press

• Each press advances picture one frame.

• Hold button down for consecutive frame advance.

• Whether pictures are advanced by “FRAME” or

“FIELD” is selected automatically. (See p. 53.)

to release.

in still mode.

■ Slow Motion Picture

(DVD/Video CD)
Press

FF/SLOW+

or

REW/SLOW-

in still mode.

PLAY

Press

• Slow motion speed, slow at first, is increased

with each additional press of the button up to
5 levels.

• Reverse slow motion is not available for Video CDs.

to release.

Auto-Power Off Function

Power turns off after DECK has been in
Stop mode (DVD) for about 5 minutes.

• When appears on the screen while a button

is being operated, it means that the
corresponding operation is prohibited by DECK
or the disc.

V.S.S. (Virtual Surround Sound)

Enjoy a surround-like effect if you are
using two front speakers only. The effect
is broadened and sound seems to come
from virtual speakers on either side if the
disc has surround signals recorded on it.

Press

VSS

• The Surround sound effects can be
changed by pressing VSS repeatedly as
shown by the figure below.

in DVD mode.

VSS OFF

Note

• Surround sound effects is available in DVD
mode only.

• Turn off the surround effects on the other
equipment.

• V.S.S. will not work, or will have less effect,
with some discs.

• Turn V.S.S. off if it causes distortion.

• Sound will only come from the two front

speakers if V.S.S. is on.

Resume Function

DECK memorizes the point where STOP is
pressed (STOP is displayed on screen).

Press

PLAY

Pressing

cancels RESUME, however, RESUME is not
canceled when power is turned off and on.

• RESUME works only with discs for which
elapsed play time is displayed during play.

Enjoy Video CDs featuring
playback control without using
menus (Video CDs only)

1. Do steps 1-4 (previous page).

When menu appears, press

2. Press

track (play begins).

• Check disc for track numbers.

• Press “1” to start at beginning of disc.

To Resume Menu use,

Press

menu will be displayed.
Now, go to step 5 (previous page).

Notes

• Please read the disc jacket for operation
information.

• If a single sided disc is placed in upside
down, “THIS TYPE OF DISC CANNOT BE
PLAYED. PLEASE INSERT A DIFFERENT
DISC” is displayed.

• Remove disc and press DECK POWER off
when not in use.

• Disc continues to rotate with menu displayed
even after play is done.
Press STOP to clear menu display when
finished with menu.

to resume play from this point.

STOP

again or opening the tray

NUMBER keys

STOP

and press

to select desired

PLAY

STOP

.

, then the

Operation

Basic

23

D4753S P1-25.p65 2003/03/13, 11:3223

Timer Recording

Ready Checklist

All connections are made. (pp. 12 ~ 15)
TV and DECK are plugged in.
Clock set correctly. (p. 18)
Tape has rec.tab. (p. 6)
Remote is in VCR mode. (Press VCR.)
Sufficient tape remaining for recording time.

Press PROG*

to display Program.

1

POWER

VCR

DATE START ST

13

SUN --:-- --:-- --

2

TODA

Y

- - - - - - - - -- - - - - - - -- - - - - - -

SESELE CT START DAT

CT :

SELE
SET

:

END

: PROG

Example

Today

14

SELECT /

13

Selection Order

WEEKLY

(SAT)

DT

START

13 10 : 00 P 12 : 00 P 02

3

-- -- : --

--

-- : -- -- : -- --

-- : -- -- : -- --

--

CANCEL : ADD / DLT
SELECT 1-8 :
E

NTER

EXIT

: PROG

OPC

E

SET

1

31

12

STOP CH

-- : -- --

: SET

1) To set record DATE,

H

SLP

press

1~31= one time, or
DAILY= MON~ FRI, or
WEEKLY= same time
each week and
press SET.

• See selection order left.

2) To set remaining items,

DAILY

WEEKLY

(SUN)

WEEKLY

(MON)

press

to select and

press SET

to set START/ STOP times,
CH (channel) or LINE
input (p. 35), and tape
speed (SP, LP, SLP).

Press PROG

to end programming.

To Enter More Programs,

SPD

SP

press

--

--

to select and

--

press SET

to set an unused program
number, and then repeat
step 2.

Or

Press PROG

to exit.

to select:

VCR mode Indicator

VCR REC Indicator

VCR

TIMER REC

Hi - Fi

TIMER Indicator

<Multi Function Display>

ADD/DLT

PROG

SELECT

SET

• The “Timer” Indicator lights up on DECK.

• You can do Timer Recording with the power on or off.

•“TIMER REC WILL START SOON” appears on-screen for 2 minutes

24

D4753S P1-25.p65 2003/03/13, 11:3224

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

before Timer Recording starts. If DECK is in DVD mode, no message
appears, but the VCR REC Indicator, the VCR mode indicator and
“REC” will flash on Multi function Display.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Review, Replace or Clear Program Contents:

(Recording is not in progress)

Press PROG

1

to display Program List.

DT

START

STOP CH

7 9 : 00A 12 : 00A 08

8

10 : 00P

2

12 : 00P 02 SP

10

8 : 00P

9 : 00P 10

U

9 : 00P 10 : 00P

S

CANC

EL : ADD /

SELECT

1-8 :
ENTER : SET
EXIT

: PROG

DLT

L1

To Replace program...

3

DATE

S

TART

S

7 SUN 9:00A 12:

TODA

Y

----------------------------------------

SELE CT

SELECT :
SET

:

END

To Clear program...

DT

START

-- -- : --

8

10 : 00P

10

8 : 00P

SU 9 : 00P 10 : 00P

CANC

EL : ADD /
SELECT
ENTER : SET
EXIT

Press PROG

to end the programming.

4

TOP

START DAT

E

SET

: PROG

or

STOP CH

-- : -- --
12 : 00P 02 SP

9 : 00P 10

DLT

1-8 :

: PROG

00A 08

BACK :

L1

SPD

Press

SP

to select number and

SP

LP

press SET

to display.

CH

Repeat Step 2 (p. 24)
to set new programs.

SP

SPD

Press ADD/DLT.

--

SP
LP

To cancel a Timer
Recording in progress...

Hold down STOP in VCR mode for

a few seconds to cancel the Timer
Recording.

(The “TIMER” Indicator goes out
on Multi Function Display.)

• Any future daily or weekly recording
will be performed as programmed.

Operation

VCR

Notes

• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to
the Cable Box input channel and Cable Box must be manually set to the desired
channel. Cable Box power must be left on.

• 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER
REC” appears and Timer Indicator flashes.
Be sure a cassette with record tab is loaded and DECK is in Stop mode.

• If a power interruption occurs while programming the timer, the timer program(s) may be
canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION”
appears on-screen, please re-enter the timer programs.

• If the start time for Timer Recording comes up during recording and playing back,
Timer Recording will not be performed.

• When recording programs via DSS Receiver, DSS Receiver must be left on.

• When recording programs via an antenna or cable, DSS Receiver must be turned off.

D4753S P1-25.p65 2003/03/13, 11:3225

Important notes when using DSS Receiver

25

MTS Broadcast/ VHS Hi-Fi Stereo System

Connection

Make the Audio/Video Connection as shown on pp. 12 ~ 15.

• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.

Receivable Broadcast Types

The following are possible audio broadcast types and on­screen displays.

The signal being received is indicated with an “

” mark

while the selected audio mode is indicated with an arrow.
To display the broadcast signal being received,

➛➛

➛ press DISPLAY*.

➛➛

MTS Stereo and SAP broadcast

Multi-channel Television Sound
Stereo (main language) and

STOP 1 2 : 0 0A

STER

EO
SAP
M

ONO

M

0 : 0 0 : 0 0

CH 02

Secondary Audio Program (sub
language) broadcasts are being
received simultaneously.
Select STEREO or SAP audio mode.

MTS Stereo broadcast

Multi-channel Television Sound
Stereo broadcast. Select STEREO

STOP 1 2 : 0 0A

STER

EO
SAP
M

ONO

M

0 : 0 0 : 0 0

CH 02

audio mode.

• If stereo broadcast is weak and
display flickers, select MONO audio
mode for possible better results.

SP

SP

DISPLAY

AUDIO

(SAP/Hi-Fi)

SAP broadcast

Secondary Audio Program (sub
language) broadcast. Select SAP
audio mode for the sub language.

MONO broadcast

Normal monaural sound broadcast.

26

D4753S P26-35.p65 2003/03/13, 11:3226

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

STOP 1 2 : 0 0A

STER

EO
SAP
M

ONO

STOP 1 2 : 0 0A

STER

EO
SAP
M

ONO

M

0 : 0 0 : 0 0

M

0 : 0 0 : 0 0

CH 02

CH 02

SP

Equipped with ®-TV
Noise Reduction for
true MTS reproduction.

®

-TV Noise
Reduction is required
for good stereo

SP

separation and audio
fidelity.

®

is a
registered trademark,
and is licensed by

®

Technology Licensing.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Audio Mode for Recording

Press AUDIO (SAP/Hi-Fi)

1

to display audio mode.

(Display disappears after 5 seconds.)

Press AUDIO (SAP/Hi-Fi) repeatedly

2

STER

EO
SAP
M

ONO

Make a recording.

3

See p. 21.

to select desired mode.

• Refer to “Receivable Broadcast Types” on p. 26.

• Arrow indicates selection.

Operation

Audio Mode for Playback

Start playback.

1

See p. 20.

Press AUDIO (SAP/Hi-Fi)

2

to display audio mode.

3

H I F I

: L / R

H I F I

: L

H I F I

:

R

N

ORM

AL

• Arrow indicates
selection.

Notes

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard
stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to
a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.

• Hi-Fi and normal audio playback volume level may differ.

Press AUDIO (SAP/Hi-Fi) repeatedly
to select desired mode.

• Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo
recordings in stereo sound.
Select “NORMAL” for monaural sound.

• Display disappears after 5 seconds.

VCR

D4753S P26-35.p65 2003/03/13, 11:3227

27

Multi-Brand Control Feature

Multi-Brand Control Setup

The Remote Control can be set to control some TV and
Cable Box/DSS functions.

Find your TV and Cable Box/DSS Receiver

1

Brand Code Number on the following page.

2

Set up for TV control,

➛➛

➛ hold down TV button,

➛➛
➛➛

➛ enter code with NUMBER keys.

➛➛

Set up for Cable or DSS control,

➛➛

➛ hold down DSS/CABLE button,

➛➛
➛➛

➛ enter code with NUMBER keys.

➛➛

• If code number is 100 or greater,

➛ e.g., press 1 - 0 - 2 for 102.

Confirm code entry,

➛ press POWER to turn selected unit on or off.

3

• See table below for controllable functions in each mode.

Notes

• Repeat setup after remote battery replacement.

• Remote will not control every TV, Cable Box, or

DSS made by the manufacturer listed. If you get
no response, your particular unit cannot be
controlled. There are NO additional codes for the
products listed. If your product is not listed, then
the remote is not compatible with that product.

Using Multi-Brand Control

After remote is set up, you can select VCR, DVD, TV, or
DSS/CABLE for the desired function.

Press VCR,

(Table below shows available remote buttons for each mode.)

Mode

Unit

DVD

, TV, or DSS/CABLE on the remote.

DVD/VCR TV

CABLE/ DSS

POWER

VCR

DSS/
CABLE

TV

DVD

NUMBER
keys

ENTER

DVD/VCR

TV

CABLE/
DSS

Notes

• Not all functions listed may be controllable.

• In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing

NUMBER keys for channel selection.

28

D4753S P26-35.p65 2003/03/13, 11:3228

EJECT/

DISPLAY, PLAY, STOP
FF/SLOW+, REW/SLOW-

VCR/TV, PAUSE

AUDIO

TAPE POSITION,
COUNTER RESET, SPEED,
REC,

PAGE

* Bold: VCR Function

Italic: DVD Function

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

All

OPEN/CLOSE

/STILL, SKIP

, CM/ZERO,

VOL +/

-

*,

,

,

POWER, INPUT,
NUMBER keys,
ENTER,
CH / ,

,

VOL +/

-

POWER, ENTER,

VOL +/-

Bold Italic: VCR and DVD Functions

Normal: TV, Cable Box or DSS Receiver

NUMBER keys
(except 100key),
CH /

TV Brand Code Numbers

Panasonic ....................... 01, 02

Quasar ............................ 01, 02

RCA ....................................... 03

GE ......................................... 03

Zenith .................................... 04

Magnavox .............................. 05

Sylvania ................................ 05

Sharp ............................... 06, 07

Sony ...................................... 08

Toshiba ................................. 09

Sanyo .................................... 10

Fisher .................................... 10

Cable Box Brand Code Numbers

Archer ......................... 44, 06, 01, 120, 05, 63, 126

Cableview ................ 29, 09, 01, 63, 120, 44, 42, 30

52, 04, 124, 126

Citizen ................... 44, 52, 30, 63, 42, 04, 124, 126

Curtis ..................................... 08, 09, 25, 61, 53, 87

Century ...................................... 44, 51, 75, 59, 126

Cabletenna .................. 29, 09, 01, 63, 120, 44, 126

Cable Cinema .............. 29, 09, 01, 63, 120, 44, 126

Diamond ...................... 29, 09, 01, 63, 120, 44, 126

Eagle ....................... 62, 40, 22, 13, 58, 20, 26, 107

Eastern ................................................... 28, 29, 130

Explorer .................................. 08, 09, 25, 61, 53, 87

Gemini ..................................................... 30, 04, 124

General Electric ...................................... 01, 57, 120

General Instruments . 01, 84, 83, 34, 03, 02, 04, 55
65, 66, 67, 68, 120, 106, 121, 122, 115, 117, 118, 124

Gerrard ............................................... 44, 51, 75, 59

GC Electronics ............... 44, 42, 63, 29, 30, 52, 04

124, 126

Hamlin ............... 41, 14, 15, 28, 102, 104, 103, 130

Hitachi ................................................................... 31

Jerrold .......... 01, 84, 83, 34, 03, 02, 04, 55, 65, 66

67, 68, 120, 106, 121, 122, 115, 117, 118, 124

Jasco ...................................................... 30, 04, 124

Macom ................................................................... 31

Magnavox ...................................................... 26, 112

Matsushita ................................. 17, 16, 08, 87, 109

Movietime ...................... 32, 39, 42, 44, 126, 38, 40

Maestro ........................................................... 74, 35

NEC .................................................... 40, 19, 38, 32

NSC .................................................... 40, 19, 38, 32

Novavision ............................. 08, 09, 25, 61, 53, 87

Next Level ...........01, 84, 83, 34, 03, 02, 04, 55, 65

66, 67, 68, 120, 106, 121, 122

Oak................................................. 46, 11, 129, 101

DSS Brand Code Numbers

Toshiba ....................................................... 90

Hitachi/ Hughes.................................... 91, 99

Primestar .................................................... 92

Drake .......................................................... 93

Magnavox ............................................. 94, 95

Uniden................................................... 94, 95

JVC........................................ 11

Hitachi ................................... 12

Mitsubishi ........................ 07, 13

Samsung ............................... 14

Gold Star ................... 15, 16, 17

Oak Sigma ..................................... 46, 11, 129, 101

Panasonic .................................. 17, 16, 08, 87, 109

Philips ................... 23, 24, 20, 13, 07, 50, 128, 129

Pioneer ......................................................06, 05, 12

Pulsar .................... 04, 42, 63, 44, 30, 52, 124, 126

Quest ........................................................ 06, 05, 12

Radio Shack ............................... 44, 51, 75, 59, 126

RCA ............................................ 17, 16, 08, 87, 109

Realistic ..................................... 44, 51, 75, 59, 126

Recoton ...................................... 44, 51, 75, 59, 126

Regal ................. 41, 14, 15, 28, 102, 104, 103, 130

Regency .................................................. 28, 29, 130

Rembrandt ....... 44, 42, 63, 29, 01, 32, 39, 120, 126

Samsung ...................................... 42, 06, 32, 05, 40

Scientific Atlanta ................... 08, 09, 25, 61, 53, 87

Sheritech ............................................................... 27

Signal ............................................................ 26, 112

SL Marx .............42, 06, 32, 40, 43, 44, 52, 63, 126

Sprucer ...................................... 17, 16, 08, 87, 109

Standard Components ............... 32, 39, 42, 44, 126

Stargate .............. 04, 42, 32, 40, 63, 44, 30, 52, 06

124, 126

Sylvania .......................................................... 19, 18

Teknika ........................................................... 74, 35

Telecaption .................................................... 77, 127

Teleview ................................. 40, 19, 38, 32, 42, 06

Texscan .......................................................... 19, 18

Tocom ................................... 34, 33, 01, 42, 66, 120

Toshiba ................................................................. 36

Unika ........................... 44, 42, 63, 29, 01, 126, 120

Universal .............................. 52, 43, 44, 63, 42, 126

Viewstar .................. 62, 40, 22, 13, 58, 20, 26, 107

Videoway .......................................... 07, 23, 50, 129

Vidtek .................................................................... 64

Zenith ............................................... 07, 23, 50, 129

Optimus ................................................ 94, 95

Panasonic ................................................... 96

ProScan ...................................................... 97

RCA ............................................................. 97

SONY .................................................. 98, 105

Operation

VCR

Important Notes

• Some manufacturers use several codes for one brand. If the first code entered fails, try the
next one listed.

• Some TV, Cable Box and DSS Receiver brands require you to turn on the power manually.

D4753S P26-35.p65 2003/03/13, 11:3229

29

Tape Operation

Search System

For each recording, an invisible index mark is placed on the tape. A program index and
information are also included for timer recordings. These marks are used to access or
scan recordings.

Index Search

Program End Search

INDEX SEARCH

1

ENTER INDEX NUMBER :1
USING 1- 9 KEYS

FORWARD SEARCH :FF
REVERSE SEARCH :REW
NEXT :SEARCH
EXIT :STOP

Press SEARCH*

to display SEARCH
in Stop or Play
mode, and then

press NUMBER
keys

to select recording
number.

• To calculate
number, see below.

Press FF/SLOW+

or REW/SLOW- on
the remote to start
search.

INDEX SEARCH

2

Play begins at
search end.
To search forward

FORWARD SEARCH : FF
REVERSE

SEARCH : REW

or back 1 index,

press FF/SLOW+ or
REW/SLOW- on the

remote while
screen left is
displayed (10 sec.).

• To cancel, press
PLAY or STOP.

To Calculate Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

61572 34

Locates end point of recording for continuity.

Press SEARCH twice
to display SEARCH in Stop or Play

1

mode.

PROGRAM END SEARCH

2

Press FF/SLOW+

on the remote to
start PROGRAM

SEARCH START : FF

EXIT

:SEARCH

END SEARCH.

• To cancel, press
PLAY or STOP.

Examples of Program End Search.
Fig. 1

Program 1

the current tape position
Press SEARCH button

FF

INDEX

Program 2 or BLANK

End Point

Fig. 2

INDEX

Program 1

Fig. 3

INDEX

the current tape position
Press SEARCH button

Program 1

End Point

the current tape position
Press SEARCH button

BLANK

BLANK

INDEX

Program 2

FF

If search exceeds

FF

a few seconds in
BLANK area.

BLANK

End Point

Program 2

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

17534 62

NOTE: indicates start points of each recording.

Note

• If Index Search is started very close to an
index mark, that index mark may not be
counted in the search.

30

D4753S P26-35.p65 2003/03/13, 11:3230

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Upon locating end point,

➛➛

➛ search continues 7 sec. past end point,

➛➛
➛➛

➛ tape rewinds to 10 sec. before end point,

➛➛
➛➛

➛ tape plays to end point and stops.

➛➛

Note

• If Program End Search is started very close to
an index mark, that mark may be skipped over.

PLAY

1st Press

2nd Press

3rd Press

1 min Skip

2 min Skip

3 min Skip

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Auto Operation Functions

Auto Play

Insert a tape ➛ Power comes on,
➛ Play starts if there is no record tab

(see p. 6).

Auto Rewind

REW/SLOW-

PLAY

FF/SLOW+

STOP

NUMBER
keys

Play
Fast Forward

Play Auto Eject

(Repeat Play must be off)

➛ ➛

➛ Tape end

Play

➛ ➛

➛ ➛

➛ Tape ejects if set some programs

➛ ➛

➛ Tape end ➛ Rewind

➛ ➛

➛ Rewind

➛ ➛

Operation

VCR

SEARCH

CM/ZERO

Commercial Skip

VCR fast forwards (skips) over 1~3 minutes
of recorded tape.

Press CM/ZERO in Play mode.

1

• The skip time can be changed by
pressing CM/ZERO repeatedly as
shown by the figure below.

• No indication appears on-screen.

31

D4753S P26-35.p65 2003/03/13, 11:3231

Tape Operation (continued)

REPEAT

REPEAT PLAY : O

FF

REMOTE W

ARN I NG

: O

N

AUTO

SHU

T-OFF

: O

FF

AUTO

VCR/TV

: OFF

SELE

CT :

SET: SET

END

: ACT I ON

SET

UP VCR

SELECT :
EXIT

: ACTION

SET : SET

MENU

SET UP VCR

SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

Repeat Play

Set to playback a recording over and over.

Press ACTION*

to display MENU.

1
2

3

SELECT :
EXIT

REPEAT

REMOTE W
AUTO
AUTO

SELE
END

MENU

SET UP VCR

SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

SET : SET

: ACTION

SET

UP VCR

PLAY : O

ARN I NG

: O

SHU

T-OFF

: O

VCR/TV

CT :

: ACT I ON

Press

to select “SET UP VCR,” and

press SET.

Press

FF

N

to select “REPEAT PLAY,”

FF

: OFF

and press SET
to set “ON” or “OFF.”

SET: SET

• Play repeats at tape end or if unrecorded portion
over 30 sec. is detected.

Press ACTION twice
to return to normal screen.

4

Note

• For repeat play in DVD mode, see page 44.

Zero Search

To quickly return to a specified tape location.

Press DISPLAY during play

1

to display Counter.

PLAY

1 2 : 0 0A

2

M

0 : 0 0 : 0 0

Press COUNTER RESET

SP

at desired position to reset
to “0:00:00”.

VCR/TV Selector FeatureVCR/TV Selector Feature

The VCR/TV selection can be set to
auto or manual.

Press ACTION

to display MENU.

1
2

3

• OFF(Manual):You select “VCR” or

• ON(Auto): “VCR” mode is

Press ACTION

to return to normal screen.

4

Note

• For more on VCR/TV selection, see
“Record one station, watch another”

and “Select channels at DECK”
sections (see p. 21).

“TV” mode using the
VCR/TV button on the
remote.

automatically set when
VCR is turned on, or in
Play mode.

Press

to select
“SET UP
VCR,” and

press SET.

Press

to select

“AUTO VCR/

TV,” and

press SET

to set “ON”
or “OFF.”

Continue to record, playback etc.

3

Press STOP.

4

REW

1 2 : 3 0A

5

STOP

1 2 : 3 1AM CH 02

M CH 02

Press CM/ZERO

0 : 30 : 30

SP

to start Zero Search.

0 : 0 0 : 0 0

SP

in Stop mode

• DECK will go into FF or REW mode and stop
at the last point the Counter was set to 0:00:00.

32

D4753S P26-35.p65 2003/03/13, 11:3232

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Special VCR Features

Weak Signal Display Feature

DISPLAY

STOP

ACTION

SELECT

SET

CM/ZERO
COUNTER

RESET

VCR Lock Feature

When set to ON, all operations
except for timer record and tape
eject are prohibited. Useful for
households with small children.

To turn on, hold down REC on
DECK in Stop mode with no
tape inserted for 7 seconds.

(Please ignore “NO CASSETTE”
warning.)

VCR LOCK ACT I VA

TED

When “ON,” picture is displayed regardless of signal
strength.

Press ACTION

1

to display MENU.

MENU
SET UP VCR
SET CLOCK

2

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

SELECT :
EXIT

: ACTION

SET UP CHA

ANT

ENNA

: CABLE

UTO SE

T

A

3

WEAK

S I GNAL D I

SELECT :
EXIT

: ACT I ON

• ON: Picture is displayed regardless of signal
condition, and may not always be clearly visible.

OFF: Screen turns solid blue when signal is weak or

non-existent.

• Selecting ON has no effect on connected equipment

with blue back feature.

Press ACTION twice
to return to normal screen.

4

Auto Shut-Off Feature

The power shuts off at a preset time.

Press ACTION

1

to display MENU.

MENU

SET UP VCR

SET CLOCK

2

SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

SELECT :
EXIT

: ACTION

*Important: If a remote control button does not work

when pressed, press the VCR button
on the remote and try the button again.

Press

to select “SET UP
CHANNEL,” and

SET : SET

NNE

SPLAY:OFF

press SET.

L

Press

to select “WEAK SIGNAL
DISPLAY,” and

press SET

SET: SET

to set “ON” or “OFF.”

Press

to select “SET UP VCR,” and

press SET.

SET : SET

Operation

VCR

To turn off, repeat above.

VCR LOCK OFF

• VCR Lock cancels in 24 hours if
clock is set.

REC

D4753S P26-35.p65 2003/03/13, 11:3233

REPEAT PLAY : O
REMOTE W

3

AUTO

AUTO

SELE
EXIT

SET

UP V

ARN I NG

SHUT-

OFF

VCR/TV

CT :

: ACT I ON

CR

: O

: O

: O

Press

FF
N

to select “AUTO SHUT-OFF.”

FF

FF

Press SET repeatedly to
change shutoff time as

SET: SET

shown below.

OFF

2 Hours

4 Hours

6 Hours

Press ACTION twice

4

to return to normal screen.

Note

• The shut-off countdown will not function during Play or
Record.

33

Special VCR Features (continued)

Remote Warning Feature

*Important: If a remote control button does not work

If Multi-brand feature is used (p. 28), and this feature is
set to on, a warning appears whenever an invalid key
is pressed in TV, DSS or CABLE mode.

Press ACTION*

to display MENU.

1

MENU

SET UP VCR

SET CLOCK

2

SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3

SELECT :
EXIT

: ACTION

REPEAT PLAY : O

3

REMOTE W

AUTO

SHUT-

AUTO

VCR/TV

CT :

SELE
EXIT

: ACT I ON

SET

ARN I NG

UP V

OFF

: O

SET : SET

CR

: O

: OFF

SET: SET

Press

to select “SET UP VCR,”
and

press SET.

Press

FF

to select

N

FF

“REMOTE WARNING,” and

press SET
to set “ON” or “OFF.”

• If “OFF,” remote warning will not appear
when invalid key is pressed.

Press ACTION twice
to return to normal screen.

4

Tape Position and Tape Status Feature

To find out the present tape position and amount of tape remaining.

Tape position is displayed for VHS-C type Cassettes, tapes
under 30 minute long, and some other tapes, but the
position is not correct.

Press TAPE POSITION

to detect current tape position.

1

DETECTING TAPE POSITION

SP

R 120 M

BEG I

N END

•“DETECTING TAPE POSITION” is displayed
only when a cassette is first inserted, and it
takes several seconds for correct tape
position to appear.

• The present tape position indication and
amount of tape remaining (according to
tape speed) is displayed.

I

N.

• Tape remaining time display may not be
precise.

when pressed, press the VCR button
on the remote and try the button again.

INPUT

STOP

PAUSE/
STILL

ACTION

SELECT

SET

TAPE
POSITION

REC

Press TAPE POSITION

to return to normal screen.

2

Note

This function cannot display exact amount of tape remaining for
tapes 30 minutes or less, or for tapes over 120 minutes in length.

34

D4753S P26-35.p65 2003/03/13, 11:3234

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Copying Your Tapes (Dubbing)

Connection

VCR/ Camcorder (Hi-Fi)

VIDEO

AUDIO

1

2

OUT

L

R

Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK.
To monitor the dubbing, also connect TV as shown.

Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R”
AUDIO IN terminals on DECK.

In place of Playing VCR, you can use other equipment, such as a Camcorder.
Simply connect the unit’s Audio/Video outputs to DECK.

DVD/VCR DECK

VIDEO

AUDIO

OUT

L

1

R

IN FROM ANT.

IN 1

VHF/UHF

OUT TO TV

Playing (Source) VCR Recording (Editing) DECK

TV

VHF/

UHF

Front of DECK

VIDEO IN 2

(Audio/Video In Terminals
on the front of DECK are
available)

L-AUDIO IN2-R

Insert a pre-recorded tape.

1
2

Press PLAY, then PAUSE/STILL

3

immediately to enter PLAY/PAUSE
mode.

The operation of steps 4 and 5 must be done on the
playing and recording VCRs at the same time.

Press PLAY to start dubbing.

Playing VCR starts playback.

4

Press STOP to stop dubbing.

5

To Monitor Dubbing on TV

1 Turn TV on and tune to the Recording

VCR channel (CH 3 or CH 4).

2 If Auto VCR/TV (see p. 32) is set to

“OFF,” press VCR/TV on the remote to
be VCR mode.

Note

Caution:• Unauthorized exchanging and/or copying of copyrighted recordings may be

• Dubbing tapes protected with Copy
Guard will result in poor quality
recordings.

copyright infringement.

• Please note that some tapes cannot be dubbed on DECK. Also, it is not
possible to dub DVD/ Video CD/ CD to VHS tapes using DECK.

Insert a blank tape with record tab.

Press INPUT to set DECK Input mode to
LINE for Video Input.

(See “Selecting the Input Mode” below.)

Press REC, then PAUSE/STILL
immediately to enter REC/PAUSE
mode.

Press PAUSE/STILL to start dubbing.
DECK starts recording.

Press STOP to stop dubbing.

Selecting the Input Mode

Method 1: Press INPUT repeatedly.

Method 2: Press CH / .

Press

•“L1” or “L2” lights up on Multi Function Display
(about 4 seconds) when LINE1 or LINE2 is selected.

• LINE1: For rear audio/video connection.
LINE2: For front audio/video connection.

Channel Number

Display will change as below.

1

2

LINE1

LINE2

3

(CABLE)

125

↔↔

↔ LINE1

↔↔

(TV)

or

69

↔↔

↔ LINE2

↔↔

Press

Operation

VCR

D4753S P26-35.p65 2003/03/13, 11:3235

35

3 ESP

SELECT
END

AUDIO

1 ENG

SELECT
END

AUDIO

ENG
FRA
DEU
ITA
ESP
NLD

English
French
German
Italian
Spanish
Dutch

SVE
NOR
DAN
POR
RUS
JPN

Swedish
Norwegian
Danish
Portuguese
Russian
Japanese

CHI
KOR
MAL
VIE
THA

∗

Chinese
Korean
Malay
Vietnamese
Thai
Other

Disc Operation

Subtitle Language (DVD-Video only)

You can select a different subtitle language (if offered) than
the one set at the Settings for DVD Operation.
(See p. 49.)

Press

1

in Play mode to display
the subtitle selection
on-screen.

SUB TITLE

• Display disappears after
5 seconds.

• When no subtitles are offered,
“-” will be displayed instead of

the language number.

Press

2

Te amo

Subtitle language being played back (see chart, right).

to select a language.

Press

to select “ON” or “OFF.”

Notes

• If after several presses of the button the language does not
change, language selection is not offered on the disc.

• When disc is removed, subtitles revert to initial setting
language. If the initial language is not recorded on the disc,
the disc’s priority language will appear.

*

Ready Checklist

Please read “Basic DVD Operation”
on page 22.

[Subtitle language]
[Audio sound track language]

Audio Soundtrack Language (DVD only)

You can change the audio soundtrack language, selected
at the Settings for DVD Operation, to a different language
if available. (See p. 49.)
(This operation works only with discs on which multiple
audio soundtrack languages are recorded.)

Press

AUDI O: 1 ENG

1

2

Dolby Digital 3/2.1ch

Hello

SELECT

:

END

:AUDIO

AUDI O: 3 ESP

Dolby Digital 3/2.1ch

Hola

SELECT

:

END

:AUDIO

Audio soundtrack language being played back (see chart,
above right).

36

D4753S P36-60.p65 2003/03/13, 11:3236

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

AUDIO

in Play mode to display the
audio selection on-screen.

• Display disappears after
5 seconds.

Audio attribute 1 type, sampling
frequency, bit No. of the disc or
number of speaker channel.

Press

to select desired language.

• Change the No. by pressing ,
and press

SET

.

[Audio attribute 1 type, sampling
frequency, bit No. of the disc (see
p. 50.)]

LPCM

Dolby Digital

DTS

~

192 kHz

1 ch - 5.1 ch
1 ch - 5.1 ch

20 bit
24 bit

Dolby Digital disc
DTS disc

Linear PCM disc

16 bit

44.1 kHz

Notes

• If, after several presses of the

AUDIO button the language does not
change, language selection is not
offered on the disc.

• When disc is removed, language

reverts to initial setting. If this
language is not recorded on the disc,
the language recorded will be heard.

Important: if a remote control button does not work when pressed,

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF

• Video CD LR L R

*

press the DVD button on the remote and try the button again.

When appears on the screen while
a button is being operated, it means
that the corresponding operation is
prohibited by DECK or the disc.

ANGLE Indicator

Notes

• The ANGLE Indicator lights up on
DECK when a scene recorded at
different angles is detected.

• The angle number can be set
beforehand so that the angle is
switched whenever the ANGLE
Indicator lights up.

SET

SELECT

SUB TITLE

ZOOM

ANGLE
AUDIO

Notes

• The subtitle cannot be enlarged nor

can it’s position be changed.

• The picture zoom feature does not

work with a Video CD.

• During picture zoom, “ZOOM1” or

“ZOOM2” appears on-screen for 5

seconds.

• Zooming, on some discs, may result

in poor picture quality, or may not
operate at all.

Multiple Angle Viewing (DVD only)

DVDs may contain scenes shot from multiple camera
angles allowing the same scene to be viewed at different
angles. You can view these angles, if available, using the
ANGLE button.

Press

ANGLE

1

SELECT :

2

SELECT :

Number of angle being played back.

Vocal Selection for Karaoke Discs

Press

1

AUDIO

to display the audio screen.

2

SELECT :
END :AUDIO

in Play mode to display the
angle selection on-screen.

• Display disappears after
5 seconds.

Press

to select the desired
angle.

(DVD/Video CD)

in Play mode

Press (or )
to select as shown below,
and
press
(DVD only)

(or ) to set.

Picture Zoom (DVD-Video only)

You can enlarge specific portions of a picture and
select the zoom ratio using the ZOOM button during
DVD playback.

Press

ZOOM

as follows.

• You can enlarge the center portion of the image
to one of 2 magnifications.

■ Use the , , and buttons to move the position

up, down, left and right.

repeatedly to change display

Operation

DVD

37

D4753S P36-60.p65 2003/03/13, 11:3237

Disc Operation (continued)

Title Menu (DVD only)

Some DVDs have more than one title, e.g. movies.
If the disc offers a title menu, you can select the desired
title number. (Operation may vary according to the disc.)

Press

TITLE

*

1

T I TLE MENU

Dogs

Love

Cas t l es

r

s

<Example>

in Play mode
to display the title screen.

i r

ds

B

2

T I TLE MENU

r

s

Cas t l es

Dogs

Love

B i rds

of the world

<Example>

i r

B

Press or

NUMBER keys

to select a title, and

press

ds

to start playing.

•“Pressing
not necessary when using

NUMBER keys.

SET

or

SET

PLAY

or

PLAY

” is

DVD Menu (DVD only)

DVDs may offer a special menu. This menu may include
guides to unique contents, audio/subtitle languages, etc.
Although contents and operation may vary, the following
steps show basic steps for using the menu.

Press

1

2

38

DVD MENU

1 . SUBT I TLE

2 . AUD

I

O

3 . ANGLE

<Example>

DVD MENU

1 . SUBT I TLE

2 . AUD

I

O

3 . ANGLE

<Example>

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

MENU

in Play mode to display
DVD MENU.

Press or

NUMBER keys

to select an item, and

press

SET

or

PLAY

to perform.

•“Pressing
not necessary when using

NUMBER keys.

Repeat step 2 if there is
more than one menu.

SET

or

PLAY

” is

PLAY

STOP

NUMBER
keys

CLEAR
ACTION

SELECT

MENU

SET

TITLE

D4753S P36-60.p65 2003/03/13, 11:3238

PLAY MODE

PROGRAM PLAY

Important: if a remote control button does not work when pressed,

*

press the DVD button on the remote and try the button again.

Program Play (Video CD/CD only)

You can program specific tracks and order of play.

Press

1

2

3

4

5

Notes

• Up to 15 tracks can be programmed.

•“ ” or “ ” (depending on disc) indicates additional

PROGRAM PLAY screen.
Press for next or previous screen.

• To clear the last program one by one

Press to move to “CLEAR LAST” and
press
also clears last program.)

• To clear all programs

Press to move to “CLEAR ALL” and press

SET.

is turned off or the disc is removed.)

ACTION

to display DVD MAIN MENU.

DVD MAIN MENU

DI SC LANGUAGES
AUDIO OUTPUT
ST IL L MODE : AUTO
TV MODE : 4: 3 L e tt er b ox
PARENTAL LOCK :

PLAY MODE

SELECT :
SET : SET
END : ACTI ON

PROGRAM PLAY

RANDOM PLAY

LEVEL 8

PLAY MODE

Press

to select
“PLAY MODE,” and

press

SET

to display.

Press

to select
“PROGRAM PLAY,”
and

SELECT :
SET : SET
END : ACTI ON

PROGRAM PLAY

DI SC PROGRAM

1 61116 5 8

2 7 12 17 15 6
3 8 13 18 1 13
4 9 14 19 3 2
5101520 2

CLEAR LAST

CLEAR ALL START
SELECT :
SET : SET
END : ACTI ON

• Repeat step 4 to select another track.

• The selected track is added on the right side.

PROGRAM PLAY

DI SC PROGRAM

1 61116 5 8

2 7 12 17 15 6
3 8 13 18 1 13
4 91419 32
5101520 2

CLEAR LAST

CLEAR ALL START
SELECT :
SET : SET
END : ACTI ON

SET

. (Pressing

(Programs are also cleared when the power

press

SET

to display.

Press

to select a track
number (Track
numbers on disc are
displayed.), and

press

SET

.

Press

to select “START,” and

press

SET

to start play
of programs in the
sequence selected.

• To cancel, press
during play, then press

CLEAR

.

CLEAR

on remote control

STOP

Ready Checklist

DECK is in DVD mode, press DVD.
Video CD or CD is inserted.

Program Repeat Play
(Video CD/CD only)

Do operation steps 1 through 5

1

at left on this page.

Press

DISPLAY

Information screen.

2

(Disc Information Screen)

TRACK : 1 VIDEO CD

PBC : OFF 01 :35 : 12

SET : SET NEXT : DISPLAY

Press

DISPLAY

DECK Information screen.

3

Press

SET

Cursor move to “OFF.”

4

(DECK Information Screen)

SET : SET END : DI SPLAY

Press to select “DISC.”

5

(DECK Information Screen)

PLAY
REPEAT : DISC
PROGRAM PLAY

SELECT :
SET : SET END : DISPLAY

Press

6

SET

Cursor move to “REPEAT.”
To cancel, select “REPEAT :
OFF” in step 5, then press

to display Disc

to display

to enter Select mode.

to set mode.

SET

Operation

DVD

.

39

D4753S P36-60.p65 2003/03/13, 11:3239

Disc Operation (continued)

PLAY MODE

Random Play (Video CD/CD only)

Tracks are played in a random order.

Press

1

ACTION

to display DVD MAIN MENU.

DVD MAI N MENU

DI SC LANGUAGES

2

AUDIO OUTPUT
ST IL L MODE : AUTO
TV MODE : 4 :3 Le t te r bo x
PARENTAL LOCK :

PLAY MODE

SELECT :
SET : SET
END : ACT ION

PLAY MODE

PROGRAM PLAY

3

RANDOM PLAY

SELECT :
SET : SET
END : ACT ION

LEVEL 8

*

Press

to select “PLAY MODE,”
and

press

SET

to display.

Press

to select
“RANDOM PLAY,” and

press

SET

to begin random play.

• To cancel, press
during play, then press

CLEAR

.

STOP

Ready Checklist

DECK is in DVD mode, press DVD.

DISPLAY

STOP
NUMBER

keys

CLEAR
ACTION

SELECT

SET
VOLUME

ADJUST

PAGE

Setting the VOLUME ADJUST

Some DVDs are recorded in lower than average volume levels.
For these DVDs, this DECK can be set so that the average
volume is increased.

Press

VOL.ADJ

•“ON” or “OFF” lights up on Multi Function Display (about 3 seconds) when
press VOL.ADJ.

repeatedly to change “ON”

VOLUME ADJUST “OFF”

Some DVD

[Volume level is low]

Volume is the original level.

•“ON” is set ..... When a DVD is played back, the average volume is increased.

•“OFF” is set .... The volume level recorded on the disc is played back just as it is.

Notes

• This feature is available only for Dolby Digital sound tracks.

• When audio equipment is connected, setting the Sound Output level to “OFF” is recommended.

• If the sound becomes abnormal while playing a disc, set the Sound Output level to “OFF.”

40

D4753S P36-60.p65 2003/03/13, 11:3240

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

↔↔

↔ “OFF.”

↔↔

VOLUME ADJUST “ON”

Volume level is increased

when played back.

Important: if a remote control button does not work when pressed,

*

press the DVD button on the remote and try the button again.

DVD-Audio Operation

This DECK, equipped with a 192 kHz/ 24 bit Audio D/A converter, supports DVD-Audio
recorded with high quality sound.
The DVD-Audio feature includes “Still Image Skip” and “Bonus Group Playback”
functions. (See below.)
Please refer to “Basic DVD Operation” on pages 22 and 23.

Still Image Skip

DVD-Audio still images (only if contained) can be skipped over.

PAGE : 1

PAGE : 2

SELECT :

SELECT :

Press PAGE

in Play or Pause mode to display the still image and page
number.

Each press of PAGE changes page number as shown below.

• Pressing PAGE on the last page returns to PAGE 1.

PAGE

Press PAGE

:

1 PAGE

Press PAGE

:

2 PAGE

Press PAGE

:

3 ....... PAGE

Press PAGE

:

XX

Note

• Still Image Skip function not available with all discs.

Bonus Group playback

Some DVD-Audio discs contain bonus groups. To enjoy these groups you may have to
enter a password. Refer to the disc's jacket.

Press

1

Note

2

Notes

3

Note

• During playback, Bonus Group tracks cannot be selected.

GROUP : 2 DVD-AUDIO
TRACK : 1 00 : 12 :34

SELECT :
SET : SET NEXT : D ISPLAY

• If the proper secret code is already entered, Bonus Group tracks can be
selected. (Secret code enter screen is skipped.)

• This code is specifically for the disc and differs from Parental Lock secret code
(p. 48). Please refer to disc jacket instructions.

BONUS GROUP
ENTER 4

• When the proper secret code has been entered, Bonus Group track 1 playback
begins. If a mistake is made, the secret code enter screen is redisplayed.

DISPLAY

-D I G I T

----

in stop mode to display “On-Screen Displays.”

Press to select “GROUP,” and press
Press or
number, and press

Press

To Make Corrections

to enter bonus group secret code, and press

CODE

Press
Press

NUMBER keys

SET

to select bonus group

(see pp. 42, 43.)

NUMBER keys

repeatedly to move the cursor.

NUMBER keys

to make the correction.

SET

.

SET

.

Operation

DVD

Press

4

D4753S P36-60.p65 2003/03/13, 11:3241

CLEAR

to return to normal screen.

41

DVD Operation using On-Screen Displays

When

DISPLAY

disc information (title/chapter/track number, elapsed
playing time) and DECK information (repeat play, play
mode).

Press

1

to display “On-Screen Displays.”

• Each press of

display as follows. (Refer to pp. 43, 44.)

➡

Press (or )

2

to select

press

is pressed, On-Screen Displays show

DISPLAY*

Selected disc information

Selected DECK information

Normal Screen

in Play or Stop mode

DISPLAY

changes the on-screen

➡

➡

an item, and

SET

.

Note

DISPLAY

does not function
while DVD TITLE
MENU is displayed.

button

Ready Checklist

DECK is in DVD mode, press DVD.

DISPLAY

NUMBER
keys

Press or
to select the setting, and

3

press

SET

.

<Example of DVD-Video>

<Example of DVD-Audio>

<Example of Video CD>

NUMBER keys

• When numbers are
displayed (e.g. title
number),
are also available.

• If the number entered is
not on the disc, the entry
will have no effect.
Re-enter the correct
number.

• For more details, refer to
the disc operation
information.

To return to normal
screen,
press

DISPLAY

NUMBER keys

CLEAR

or

repeatedly.

CLEAR

SELECT

SET

Notes

• When

• When appears on the screen while

DISPLAY

during playback of a Video CD with
Playback control,
not available on the displayed screen.
In this case, press
remove the displayed screen.

a button is being operated, it means
that the corresponding operation is
prohibited by DECK or the disc.

button is pressed

NUMBER keys

DISPLAY

again to

are

42

D4753S P36-60.p65 2003/03/13, 11:3242

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Important: if a remote control button does not work when pressed,

SELECT :
SET : SET NEXT : DISPLAY

T ITLE : 1 DVD

CHAPTER : 12 01: 12 :55

SET : SET NEXT : DISPLAY

TRACK : 1 VIDEO CD

PBC : OFF 01 :35 : 12

ENTER : 0 - 9
SET : SET NEXT : DISPLAY

T ITLE : 1 DVD
CHAPTER : 12 01:

--:--

ENTER : 0 - 9
SET : SET NEXT : DISPLAY

GROUP : 1 DVD-AUDIO
TRACK : 1 01 :

--:--

*

press the DVD button on the remote and try the button again.

Detailed Descriptions of each On-Screen Display

■■

■ Disc information screen (for DVD-Video)

■■

1. TITLE No.

• Select “TITLE”, and press

• Change the No. by pressing

2. CHAPTER No.

• Select “CHAPTER”, and press

• Change the No. by pressing or

3. Disc currently being played

4. Elapsed playing time

The screen may be changed by selecting the elapsed time.

• Select the elapsed playing time (“xx:xx:xx”), and press

• Change the elapsed time by pressing

Hours ➛ Minutes ➛ Seconds are entered in order.
If the time entered is not on the disc, the entry will have no effect.
Re-enter the correct time.
e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.

Hour Minutes Seconds

• This function does not work with some discs.

■■

■ Disc information screen (for DVD-Audio)

■■

A.GROUP No.

• Select “GROUP”, and press

• Change the No. by pressing or

B.TRACK No.

• Select “TRACK”, and press

• Change the No. by pressing or

C.Disc currently being played
D.Elapsed playing time

The screen may be changed by selecting the elapsed time.

• Select the elapsed playing time (“xx:xx:xx”), and press

• Change the elapsed time by pressing

Hours ➛ Minutes ➛ Seconds are entered in order.
If the time entered is not on the disc, the entry will have no effect.
Re-enter the correct time.
e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.

Hour Minutes Seconds

• This function does not work with some discs.

■■

■ Disc information screen (for Video CD/ CD)

■■

a. TRACK No.

• Select “TRACK”, and press

• Change the No. by pressing or

b. Playback control ON/OFF

[Video CD with playback control only]

ON Video CD menu play is displayed.
OFF Video CD menu play is not displayed.

c. Disc currently being played

Video CD CD

d. Elapsed playing time

Notes

• Track No. and the elapsed playing time are not displayed during play started from
menu of Video CDs with playback control.

• When appears on the screen while a button is being operated, it means that the
corresponding operation is prohibited by DECK or the disc.

SET

SET

SET

SET

.

or

SET

.

.

NUMBER keys

.

NUMBER keys

NUMBER keys

.

NUMBER keys

NUMBER keys

NUMBER keys

NUMBER keys

, and press

, and press

SET

.

, and press

, and press

SET

.

, and press

SET

SET

.

SET

SET

.

SET

1
2

.

.

If SET is pressed while
making entries, unit returns
to the condition it was in
before entries were made.

A
B

.

.

If SET is pressed
while making entries,
unit returns to the
condition it was in
before entries were
made.

.

a
b

3

4

C
D

Operation

DVD

c
d

43

D4753S P36-60.p65 2003/03/13, 11:3243

DVD Operation using On-Screen Displays (continued)

SELECT :
SET : SET END : DISPLAY

PLAY

REPEATREPEAT : CHAPTER

SET : SET END : DI SPLAY

PLAY

REPEAT REPEAT : DI SC

RANDOM PLAY

■■

■ DECK information screen (for DECK)

■■

1

. Repeat Play

• Select “REPEAT”, and press

• Change the desired mode during play by pressing , and press

DVD-Video CHAPTER TITLE OFF
DVD-Audio TRACK GROUP OFF
Video CD/CD TRACK DISC OFF

2

. Play mode [Video CD/ CD only] (See p. 39 or 40.)

PROGRAM PLAY program play
RANDOM PLAY random play

----

normal play

For your reference

SET*

.

SET

.

1

•

CHAPTER/TITLE REPEAT PLAY (DVD-Video)

CURRENT PLAYBACK POSITION

TITLE

chapter

CHAPTER REPEAT

TITLE REPEAT

NORMAL PLAY

•

TRACK/GROUP REPEAT PLAY (DVD-Audio)

CURRENT PLAYBACK POSITION

GROUP

track

track

TRACK REPEAT

GROUP REPEAT

NORMAL PLAY

•

TRACK/DISC REPEAT PLAY (Video CD/CD)

TRACK REPEAT

DISC REPEAT

NORMAL PLAY

chapter

GROUP

track

track

CURRENT PLAYBACK POSITION

track

track

track

chapter

track

track

2

OPEN/
CLOSE

POWER
PLAY

FF/REW
PAUSE

STOP

NUMBER
keys

SKIP

SKIP
SELECT

SET

ACTION

• For repeat play in VCR mode, see p. 32.

Note

Important: if a remote control button does not work when pressed,

*

44

D4753S P36-60.p65 2003/03/13, 11:3244

press the DVD button on the remote and try the button again.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

MP3/WMA/JPEG Playback Operation

This unit can play MP3/WMA/JPEG format CD-R or
CD-RW recorded for personal use on a PC, etc.
Some discs may not play due to the condition of the
recording.

Press

1

2

POWER

Press

OPEN/CLOSE

then place an MP3/WMA/JPEG disc into

on the remote or DECK.

,

the disc tray.

Press

OPEN/CLOSE

• MP3/WMA/JPEG menu is displayed.

• Playback starts automatically

3

(except JPEG files).

• CD directory is displayed.

Function

Status

Folder area

(Current folder

appears green.)

:MP3 file :WMA file

:Folder :Parent folder
:JPEG file

<Example>

ROOT

VA

TECHNO

POPS

J

AZZ

• Select file (During STOP mode)

1)Press to select an MP3/WMA file ( / ).

4

2)Press to select a JPEG file ( ).

3)Press

• Select folder (During STOP mode)

1)Press to select a folder ( ).

2)Press

• Select parent folder (During STOP mode)

1)Press to select a folder ( ).

2)Press

Press

5

MENU. (➛ Press

PLAY

ROOT . .

VA

END_W

TECHNO

POPS
J

AZZ

PLAY MODE : NORMAL

PLAY MODE

(Diagram left shows CD directory
structure as displayed in example
OSD above.)

END_W

ALTZ
DD_CUB I C
N

O

CTURNE

N

O

RN

➡ MP3/WMA Playback (see right)

➡ JPEG Playback (see p. 46)

(previous) to skip a file/folder page (7files)
in the File area.

in the folder.

directory display.

Notes

• Only File (not Folder) area
operation is possible.

• Files are displayed in the
following order:

(!...0,1....9,A,B......Z).

SKIP

SET

to display files/folders contained

SET

to make changes to the previous

ACTION

to close.

<Example>

00 : 00 :

00

Counter

Parent
folder

File area

(Selected file/
folder is
highlighted.
Titles are
displayed
up to 11
characters.)

SKIP

ALTZ

DD_

CUB I C

NOCTURNE

NORN

| (next) or |

to return the DVD MAIN

ACTION

again to return

to the MP3/WMA/JPEG MENU.)

MP3/WMA Playback

Do steps 1~3 on left.

Press to select an MP3/WMA file (

a

(During STOP mode)

Press

SET

or

PLAY

b

■ Forward/Reverse Search
Press

FF/SLOW+

Press

PLAY

• Search speed, slow at first, increases with each

additional press of the button up to 5 levels.

■ Forward/Reverse Track Skip
Press

Each press skips a track.

• If pressed within first 3 seconds of playback,

skips to the previous track. If over 3 seconds,
returns to top of track. (|

• Put DECK in Stop mode before performing

folder/file selection (see step 4.)

■ Pause
Press
Press

Press

c

Press

The MP3/WMA/JPEG MENU is closed

d

automatically.

Note

■ Select PLAY MODE [MP3/WMA Playback]

(During STOP mode)

1) Press to move cursor to

PLAY MODE.

2) Press to select the desired PLAY

MODE (see below).

[PLAY MODE]
NORMAL:

All MP3/WMA files are selected and
played back one time only.

SINGLE REPEAT:

The selected MP3/WMA file is played
back repeatedly.

FOLDER REPEAT:

The MP3/WMA files contained in the
selected folder are played back
repeatedly. However, folders below the
selected folder are not played back.

DISC REPEAT:

All MP3/WMA files are played back
repeatedly.

to release.

SKIP

| or |

PAUSE
PLAY

to release.

STOP

OPEN/CLOSE

• Copyright protected files and files
containing errors cannot be played
back. The DECK skips to the next file.

to start playback.

or

REW/SLOW-

SKIP

during play.

to stop play.

during play.

during play.

SKIP

only.)

to eject the disc.

/

).

Operation

DVD

45

D4753S P36-60.p65 2003/03/13, 11:3245

MP3/WMA/JPEG Playback Operation (continued)

JPEG Playback

You can play back JPEG images.
Displayable Image Size: 32x32~7680x7680 pixels

• Some JPEG format may not be played

Note

Do steps 1~3 on page 45.

1
2

■ Returned on the MP3/WMA/JPEG MENU

■ Next/Previous Search

■ Start Slide-show ➡ Press

■ Enlarging an image ➡ Press

■ Rotating an image ➡ Press

3

back.

Press to select an JPEG file ( ).

Press

SET

or

PLAY

.

Selected JPEG file is displayed.

[JPEG Playback Screen]

<Example>

➡ Press

➡ Press

REW/SLOW-

Press

JPEG MENU.

STOP

. (See p. 45)

SKIP

| or |

. (below)

STOP

to return the MP3/WMA/

SKIP

.

FF/SLOW+

ZOOM

ANGLE

or

. (P. 47)
. (P. 47)

■ Select PLAY MODE [JPEG Slide-show]

(During STOP mode) (See p. 45)

1) Press to move cursor to

PLAY MODE.

2) Press to select the desired PLAY

MODE (see below).

[PLAY MODE]
NORMAL:

All JPEG files are selected and
played back one time only.

SINGLE REPEAT:

The selected JPEG file is played back
repeatedly.

FOLDER REPEAT:

The JPEG files contained in the
selected folder are played back
repeatedly. However, folders below the
selected folder are not played back.

DISC REPEAT:

All JPEG files are played back
repeatedly.

JPEG Slide-show

(During JPEG Playback.)

JPEG files are displayed automatically
(about every 3 seconds) as a slide-show.

Press

1

<Example>

Image changes every 3 seconds.

■ Cancel slide show

■ Still picture

■ Forward/Reverse File Skip

2

46

D4753S P36-60.p65 2003/03/13, 11:3246

FF/SLOW+

➡ Press

➡ Press
➡ Press

➡ Press

Press
MENU.

STOP

JPEG MENU. (See p. 45)

STILL

PLAY

SKIP

Each press skips a file.

ACTION

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

or

REW/SLOW-

to return the MP3/WMA/

(only SLIDE).

to release.

| or |

to return to the DVD MAIN

SKIP

<Example>

Operation can be done when files are in
order, such as in the diagram below.

.

.

ROOT

01 PIC

REW/SLOW-

FF/SLOW+

AAA
DDD
TTT
UUU
VVV
WWW
ZZZ

REW/SLOW-

FF/SLOW+

PLAY

REW/
SLOW-

STOP

FF/
SLOW+

STILL

JPEG Zoom

(During JPEG Playback.)

You can enlarge specific portions of a JPEG picture
and select the zoom ratio using the ZOOM button
on the remote during JPEG Playback screen.

Set Zoom size.

Press

ZOOM

follows.

Press

➡

• You can enlarge the center portion of the image to
one of 2 magnifications.

• Operation can be done during Rotation (below).

X 1.0 (ORIGINAL)

repeatedly to change display as

STOP

to return the MP3/WMA/JPEG MENU.

X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)

1st press

2nd press

SKIP

ACTION

SET

SKIP
SELECT

ZOOM
ANGLE

■ Use the , , and buttons to move the

position up, down, left and right.
(Position cannot be changed on X1.0
ORIGINAL images.)

JPEG Rotation

(During JPEG Playback.)

You can rotate a JPEG picture using the ANGLE
button on the remote during JPEG Playback
screen. (The JPEG picture will be rotated 90 °
clockwise.)

Set rotation.

Press

ANGLE

as below.

Press

➡

• Operation can be done during Zoom (above).

• The vertical/horizontal ratio of rotated JPEG

images may vary when they are displayed.

1st press

MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and
Thomson multimedia.

2nd press 3rd press

repeatedly to change display

STOP

to return the MP3/WMA/JPEG MENU.

3rd press

Operation

DVD

4th press

Windows Media, and the Windows logo are trademarks, or registered
trademarks of Microsoft Corporation in the United States and/or other countries.
WMA is a compression format developed by Microsoft Corporation. It achieves
the same sound quality as MP3 with a file size that is smaller than that of MP3.

D4753S P36-60.p65 2003/03/13, 11:3247

47

DVD Lock Feature

*Important: If a remote control button does not work when

pressed, press the DVD button on the remote
and try the button again.

You can prevent playback of DVDs of a specific
rating level which may be unsuitable for children.

• Some DVDs are encoded with a rating level. If the disc
rating is higher (stricter) than the one you preset,
playback will be prohibited.

DVD Lock (DVD-Video only)

A 4-digit code must be entered to view a blocked
program or change rating settings.

Press

ACTION

to display DVD MAIN MENU.

1

DVD MAIN MENU

DI SC LANGUAGES
AUDIO OUTPUT

2

ST IL L MODE : AUTO
TV MODE : 4:3 Letterbox

PARENTAL LOCK : LEVEL 8

SELECT :
SET : SET
END : ACTI ON

3

ENTER 4-D I G I T

----

ENTER : 0

-

END

: ACT I O

9

To Make Corrections

Press repeatedly to

move the cursor.

Press

NUMBER keys

make the correction.

4

LEVEL 0 : LOCK ALL, Playback of all DVDs, CDs, Video

LEVEL 1 : mature theme DVDs
LEVEL 2 : DVDs expressly for children can be played back.
LEVEL 3 to 7 : DVDs for general audiences/children can be

LEVEL 8 : NO LIMIT: (Factory preset)

CDs, WMA, MP3 and JPEG is prohibited.
(Use to prohibit play of mature theme DVDs not
encoded with rating level.)

All DVDs can be played back.

*

Press

to select “PARENTAL LOCK,”
and

press

SET

to display.

1) Press

CODE

N

2) Enter same secret code

3) Press

• Step 2) not necessary when
changing rating or secret
code.

• Take care that you are not

to

observed entering the
secret code.

NUMBER keys

to enter your secret code.

again for confirmation.

SET

to display.

Press

to select rating level, and

press

SET

to select “LOCKED” or
“UNLOCKED.”

played back. (DVDs with mature content
are prohibited.)

Ready Checklist

DECK is in DVD mode, press DVD.

Caution

Discs not encoded with rating
level will play even if the jacket
states it is for mature
audiences. For these discs, the
DVD Lock Ratings will not work.

<When DVD Lock is activated>

YOUR SELECTI ON EXCEEDS THE

,

PLAYER S RATI NG LIMIT.
DO YOU WANT TO CHANGE THE
LIMIT?

YES

NO

SELECT:
SET : SET END : D ISPLAY

After DVD Lock is set and a
blocked DVD is played, this
message will appear.
The message may differ
depending on the disc.

To continue viewing a blocked
program for now,

Press to select “YES” and

SET. Then, enter your 4 digit
secret code (see step 3 left).

When “NO” is selected, blocked
programs cannot be viewed.

<When blocked programs>

PROGRAM RATING EXCEEDED

Change your secret code

• You will need your current code.
Do steps 1 ~ 2 left.
Enter current secret code.

Press

CLEAR

Do step 4 to enter new code.

to clear the code.

48

D4753S P36-60.p65 2003/03/13, 11:3248

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Note

• DO NOT forget your secret code.

Settings for DVD Operation

Press

ACTION

1

to display DVD MAIN MENU.

DVD MAIN MENU

DI SC LANGUAGES

AUDIO OUTPUT

2

ST IL L MODE :
TV MODE : 4:3 Letterbox
PARENTAL LOCK :

SELECT :
SET : SET
END : ACTI ON

AUTO

LEVEL 8

Press

to select an item, and

press

SET

.

DISC LANGUAGES (See below)

All languages offered on the disc can be set.
If the language not offered is set, the original disc
language will be selected.

AUDIO OUTPUT (See p. 50.)

You can set the audio output that comes from the
digital audio output terminal.

STILL MODE (See p. 53.)

To select “FIELD” (Field still) or “FRAME” (Frame
still) to prevent jitter or make small text or fine
patterns clearly visible in a still picture. When
“AUTO” is set “FIELD” or “FRAME” is selected
automatically.

TV MODE (See p. 53.)

To select whether the video material for a wide­screen will be played back in the Pan & Scan style,
Letterbox style or 16 : 9 style.

Disc Languages (DVD only)

To select and set the language of the audio
soundtrack, subtitles, or title/DVD menus for all discs
to be played.

DVD MAIN MENU

DI SC LANGUAGES

AUDIO OUTPUT

3

ST IL L MODE :
TV MODE : 4:3 Letterbox
PARENTAL LOCK :

SELECT :
SET : SET
END : ACTI ON

AUDIO : English

SUBT ITLE : AUTO

4

MENUS : English

SELECT :
SET : SET
END : ACTI ON

Press

MENU and go to step 2 to setup another

5

AUTO

LEVEL 8

DI SC LANGUAGES

ACTION

item.
Or, press

ACTION

Press

to select
“DISC LANGUAGES,”
and

press

SET

to display screen.

Press

to select an item, and

press

SET

repeatedly
for desired language.
(Please refer right.)

to redisplay DVD MAIN

twice to exit.

Once initial settings are done, they
remain in memory (even after power off)
until changed. This means DECK will
operate under the same conditions
(especially DVDs) each time.

Ready Checklist

DECK is in DVD mode, press DVD.

NUMBER
keys

CLEAR

ACTION
SELECT

SET

“AUDIO” selections

(Factory preset: English)

To select the audio soundtrack language.

English/Spanish/French/Japanese
Original: Original disc language

OTHER ✱✱✱✱: Other language selection*

“SUBTITLE” selections

(Factory preset: AUTO)

To select the subtitle language.

AUTO: Same language selected

for “AUDIO”

• If language set for “AUDIO” is used in

playback, subtitles will not appear.

• If another language is used during

playback, the subtitles will appear
in the language selected at “AUDIO”
setup.

English/Spanish/French/Japanese
OTHER ✱✱✱✱: Other language selection*

“MENUS” selections

(factory preset: English)
To select the language used in title
menus or DVD menus.

English/Spanish/French/Japanese
OTHER ✱✱✱✱:

To enter OTHER ✱✱✱✱

Other language selection*

code

number,

Press

NUMBER keys

language codes on p. 54).
To make corrections, press
repeatedly to delete language code
number, and correct.

*1If the selected language is not offered,

the original disc language is selected.

(Please refer to

1

Operation

DVD

1

1

49

D4753S P36-60.p65 2003/03/13, 11:3249

Settings for DVD Operation (continued)

Audio Output

Select the digital output to be output from the optical
digital audio output connector of DECK.

ACTION

Press

to display DVD MAIN MENU.

1

DVD MAI N MENU

DI SC LANGUAGES

2

AUDIO OUTPUT

ST IL L MODE : AUTO
TV MODE : 4:3 Letterbox
PARENTAL LOCK :

SELECT :
SET : SET
END : ACT ION

AUDI O OUTPUT

LPCM(DVD) : OFF

3

Dolby Digital : Bitstream
dts : Bitstream
DRC : OFF
SPEAKER SETUP

SELECT :
SET : SET
END : ACT ION

■■

■ “LPCM (DVD)” selections

■■

OFF: Linear PCM of less than 48 kHz/16 bit is

output. When playing DVDs recorded in linear
PCM of over 48 kHz/20 bit, no digital audio is
output. (Factory preset)

PCM: When playing DVDs recorded in linear PCM of

48 kHz/20 bit/24 bit or more, digital audio
converted to 44.1 kHz/16 bit or 48 kHz/16 bit is
output.
(Digital output of PCM audio is restricted to48
kHz/16 bit or below for copyright protection.)

■■

■ “Dolby Digital” selections

■■

Bitstream: Dolby Digital bitstream (1 ch - 5.1 ch) is

PCM: When you have connected a amplifier that

doesn’t have a built-in Dolby Digital decoder.

■■

■ “dts” selections

■■

Bitstream: DTS bitstream is output. (Factory preset)
PCM: When you have connected a amplifier that

doesn’t have a built-in DTS decoder.

■■

■

“DRC (Dynamic Range Compression)”

■■

selections

OFF: Normal audio range is selected. (Factory preset)
ON: For dynamic sound even at low volume, this

is useful for late-night listening. [Dolby Digital
DVDs only].

■■

■

SPEAKER SETUP

■■

See pages 51, 52, 53.

➡

*

Press

to select

LEVEL 8

“AUDIO OUTPUT,”
and

press

to display screen.

Press

to select an item,
and

press

repeatedly for
output. (See below.)

output. (Factory preset)

SET

SET

Ready Checklist

DECK is in DVD mode, press DVD.

Type of amplifier
to be connected

No amplifier is connected
AV amplifier (with digital

audio input connector)
without Dolby Digital/DTS
decoder

AV amplifier including
Dolby Digital decoder

AV amplifier including
Dolby Digital/DTS decoder

• Make settings according to amplifier
connected to optical audio output as shown
in above table.

*1 When connecting an amplifier (with an

optical digital input connector) which does
not contain the Dolby Digital or DTS
decoder, be sure to select “PCM”.
If “Bitstream” is selected, starting DVD play
may cause such a high level of noise as to
be harmful to your ears and damage the
speakers.

*2 When a DTS decoder is connected, please

select “Bitstream” in “dts”.

Recommended setting

LPCM

(DVD)

PCM

PCM

PCM

Dolby

Digital

1

PCM*

Bitstream

Bitstream

DTS

PCM*

PCM

Bitstream

1

2

*

Press

ACTION

MENU and go to step 2 to setup another

4

to redisplay DVD MAIN

item.
Or, press

50

D4753S P36-60.p65 2003/03/13, 11:3250

ACTION

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

twice to exit.

*Important: If a remote control button does not work when pressed,

SPEAKER SETUP

SPEAKER OUTPUT : MULTI-CHANNEL

FRONT

: LARGE

press the DVD button on the remote and try the button again.

Speaker Output Setup

Set the number of speakers connected to the receiver
(amplifier, decoder.) (See pp. 14, 15.)

Do steps 1~3 on page 50.

1

AUDI O OUTPUT

LPCM(DVD) : OFF

2

Dolby Digital : Bitstream
dts : Bitstream
DRC : OFF

SPEAKER SETUP

SELECT :
SET : SET
END : ACT ION

SPEAKER SETUP

SPEAKER OUTPUT : MULTI-CHANNEL

3

SPEAKER SIZE
OUTPUT BALANCE
DELAY TIME

SELECT :
SET : SET
END : ACT ION

■■

■ SPEAKER OUTPUT

■■

MULTI-CHANNEL: (Factory preset)

Use this setting when 3 or more speakers are
connected. In this case, it is necessary to set
[SPEAKER SIZE], [OUTPUT BALANCE], and
[DELAY TIME].

2-CHANNEL:

When 2 speakers are connected, it is not
necessary to set [SPEAKER SIZE], [OUTPUT
BALANCE], and [DELAY TIME] (these setting
menu are not displayed.)

Press

to select “SPEAKER
SETUP,” and

SET

press

to display
SPEAKER SETUP
screen.

Press

to select “SPEAKER
OUTPUT,”
and

press

SET

repeatedly.

(See below.)

ACTION

SELECT

SET

Press

4

ACTION

three times to exit.

Speaker Size Setup

Speaker frequency properties and the existence of speakers is set.

Do steps 1~2 of “Speaker Output Setup” above.

1

SPEAKER SIZE

FRONT

2

CENTER : LARGE
SURROUND : LARGE
SUBWOOFER :

Menu item
FRONT

CENTER

SURROUND

SUBWOOFER

Press

3

D4753S P36-60.p65 2003/03/13, 11:3251

: LARGE

O

N

SELECT :
SET : SET
END : ACT ION

Setting
LARGE(factory preset)

SMALL
LARGE(factory preset)
SMALL
NONE
LARGE(factory preset)
SMALL
NONE
ON(factory preset)
OFF

ACTION

Press

to select “SPEAKER SIZE,” and press
to display SPEAKER SIZE screen.

Press

to select an item, and press
repeatedly. (See below table.)

When the front speakers (R/L) supports low-frequency (under 100 Hz) reproduction.
Select when the front speakers (R/L) does not support low-frequency reproduction.
When the center speaker supports low-frequency (under 100 Hz) reproduction.
Select when the center speaker does not support low-frequency reproduction.
If there is no center speaker.
When the surround speakers (R/L) supports low-frequency (under 100 Hz) reproduction.
Select when the surround speakers (R/L) does not support low-frequency reproduction.
If there is no surround speaker.
If there is a subwoofer.
If there is no subwoofer speaker.

Remark

four times to exit.

SET

**If SUBWOOFER is set to “OFF,”

the front speakers are set to
“LARGE” automatically.

Operation

DVD

SET

51

Settings for DVD Operation (continued)

CENTER

: 0dB

Output Balance Setup

Adjust the volume level output from the speakers. To adjust, play a disc or set the “TEST SIGNAL”
(p.53) to ON. Then adjust while confirming the volume. (Even if “OFF” or "NONE" is set in “SPEAKER
SIZE,” the speaker OUTPUT BALANCE can still be set.)

Do steps 1~2 of “Speaker Output Setup” on page 51.

1

OUTPUT BALANCE

CENTER

2

SURROUND(R) : 0dB
SURROUND(L) : 0dB
SUBWOOFER : 0dB
TEST SIGNAL : OFF

SELECT :
SET : SET
END : ACT ION

Menu item

CENTER

SURROUND(R)

SURROUND(L)

SUBWOOFER

TEST SIGNAL : Switch test signal used for OUTPUT BALANCE setting to “OFF” or “FRONT(L)”....

➡ See page 53.

: 0dB

0dB(factory preset)

Press

to select “OUTPUT BALANCE,” and press
to display OUTPUT BALANCE screen.

Press

to select an item, and press
(See below table.)

Setting

-6dB

~

+6dB

*

SET

SET

repeatedly.

Remark

Adjust so that the center speaker volume is virtually the same
level (-6dB ~ +6dB) as the front speakers.

Adjust so that the surround speaker(R) volume is virtually
the same level (-6dB ~ +6dB) as the front speakers.

Adjust so that the surround speaker(L) volume is virtually
the same level (-6dB ~ +6dB) as the front speakers.

Adjust so that the subwoofer speaker volume is optimum.
However, because no test sound will come from the
subwoofer, play a disc to confirm, then adjust.

Press

3

ACTION

four times to exit.

Delay Time Setup

To enjoy 5.1 CH sound, it is ideal to place all
speakers, except the subwoofer, in a circular
arrangement. (See <Speaker Position> p. 53.)
If this is not possible, setting Delay Time gives the
sound output a delayed effect which gives you the
illusion of the ideal listening position. (See right.)

Do steps 1~2 of “Speaker Output

1

Setup” on page 51.

Press

2

to select “DELAY TIME,” and press
to display DELAY TIME screen.

Press

to select an item, and press
repeatedly. (See below.)

Menu item

CENTER

SURROUND

3

52

D4753S P36-60.p65 2003/03/13, 11:3252

0ms 1ms 2ms 3ms 4ms 5ms

0ms 5ms 10ms 15ms 20ms

Press

ACTION

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Setting

three times to exit.

SET

Remark

Setting a delay effect.

0ms(Factory preset)

SET

[See <Speaker Position> p.53.]

• , : Delay time as 0ms

• , < : Find the distance B1, C1 in the

Center speaker

B1

Approx. 50 cm (1 feet)
Approx. 100 cm (3 feet)
Approx. 150 cm (5 feet)
Approx. 200 cm (6 feet)

Surround speaker

C1

Approx. 200 cm (6 feet)
Approx. 400 cm (12 feet)
Approx. 600 cm (18 feet)

(Factory prest)

table (below) and change to
the recommended setting.

Distance

Distance

B1

C1

1

/2

Setting

1.3 ms

2.6 ms

3.9 ms

5.3 ms

Setting

5.3 ms

10.6 ms

15.9 ms

*Important: If a remote control button does not work when pressed,

TEST SIGNAL

: OFF

TILLLL

MODE

: AUTO

press the DVD button on the remote and try the button again.

Test Signal Setup

This feature assists in the setting of
OUTPUT BALANCE. Starting with (L) front
speaker, a test sound is output in clockwise
order. While the test signal is output, adjust
the output of the center speaker and
Surround speaker (R/L).
(See “Output Balance Setup.” P. 52.)

Do steps 1~2 of “Output

1

Balance Setup” on page 52.

OUTPUT BALANCE

CENTER : 0dB

2

SURROUND(R) : 0dB
SURROUND(L) : 0dB
SUBWOOFER : 0dB

TEST SIGNAL

SELECT :
SET : SET
END : ACT ION

No sound will come from the subwoofer.
Adjust as desired when playing a disc.
While the TEST SIGNAL is output, if the
setting change in the OUTPUT BALANCE
(p. 52) is under 2 seconds, the output will
switch to the next speaker. The speaker
name from which the TEST SIGNAL is
currently being output is displayed.
(Example; "TEST SIGNAL : CENTER")

Press

3

FRONT(L)

SURROUND(L)

: OFF

FRONT(L) CENTER FRONT(R)OFF

2sec

SURROUND(L) SURROUND(R)

2sec 2sec

ACTION

CENTER

Listening
position

<Speaker Position>

TV Mode
Example

Press

to select “TEST
SIGNAL,” and

press

SET

(See below.)

2sec

four times to exit.

B1

FRONT(R)

SUBWOOFER

SURROUND(R)

C1

[Pan & Scan (Factory preset)]

.

2sec

Still Mode

Set to reduce jitter in a displayed still picture or a motion
picture.

Press

1

2

AUTO: “FIELD” (Field still) or “FRAME” (Frame still) is

FIELD: “FIELD” (Field still) is always selected.

FRAME:“FRAME” (Frame still) is always selected.

3

ACTION

to display DVD MAIN MENU.

DVD MAI N MENU

DI SC LANGUAGES
AUDIO OUTPUT

STI

MODE

TV MODE : 4 :3 Letterbox
PARENTAL LOCK :

SELECT :
SET : SET
END : ACT ION

Press

: AUTO

LEVEL 8

automatically selected during the still mode.

(Factory preset)

This setting will reduce jitter when compared

with “AUTO” on some discs.

Some texts and fine patterns will be seen clearly

when compared with “AUTO” on some discs.

ACTION

Press

to select “STILL MODE,”
and

SET

press

repeatedly

for mode. (See below.)

to exit this mode.

TV Mode

Set the screen display style for wide-screen video
material playback.

Press

ACTION

to display DVD MAIN MENU.

1

DVD MAI N MENU

DI SC LANGUAGES

2

AUDIO OUTPUT
ST IL L MODE : AUTO

TV MODE : 4 :3 Le t te rb o x

PARENTAL LOCK :

SELECT :
SET : SET
END : ACT ION

4:3 Pan & Scan (Factory preset) :

Wide-screen video data is played in
Pan & Scan style (left and right of screen
is trimmed.)

• Video data not formatted in Pan & Scan
will play in letterbox style.

4:3 Letterbox :

Wide-screen video data is played in
Letterbox style (top and bottom of screen
has black margin).

16:9 :

Set “16:9” when using Wide-screen TV.

Press

to exit this mode.

3

LEVEL 8

ACTION

Press to select “TV

MODE,” and press
repeatedly for
mode.
(See below.)

[Letterbox]

SET

Operation

DVD

53

D4753S P36-60.p65 2003/03/13, 11:3253

Language Code List

Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or
“MENUS” (see p. 49).

Code Language

6565 Afar
6566 Abkhazian
6570 Afrikaans
6577 Ameharic
6582 Arabic
6583 Assamese
6588 Aymara
6590 Azerbaijani
6665 Bashkir
6669 Byelorussian
6671 Bulgarian
6672 Bihari

Bengali; Bangla

6678
6679 Tibetan
6682 Breton
6765 Catalan
6779 Corsican
6783 Czech
6789 Welsh
6865 Danish
6869 German
6890 Bhutani
6976 Greek
6978 English
6979 Esperanto
6983 Spanish
6984 Estonian
6985 Basque
7065 Persian
7073 Finnish
7074 Fiji

Code Language

7079 Faroese
7082 French
7089 Frisian
7165 Irish
7168 Scots Gaelic
7176 Galician
7178 Guarani
7185 Gujarati
7265 Hausa
7273 Hindi
7282 Croatian
7285 Hungarian
7289 Armenian
7365 Interlingua
7378 Indonesian
7383 Icelandic
7384 Italian
7387 Hebrew
7465 Japanese
7473 Yiddish
7487 Javanese
7565 Georgian
7575 Kazakh
7576 Greenlandic
7577 Cambodian
7578 Kannada
7579 Korean
7583 Kashmiri
7585 Kurdish
7589 Kirghiz
7665 Latin

Code Language

7678 Lingala
7679 Laothian
7684 Lithuanian

Latvian, Lettish

7686
7771 Malagasy
7773 Maori
7775 Macedonian
7776 Malayalam
7778 Mongolian
7779 Moldavian
7782 Marathi
7783 Malay
7784 Maltese
7789 Burmese
7865 Nauru
7869 Nepali
7876 Dutch
7879 Norwegian
7982 Oriya
8065 Panjabi
8076 Polish

Pashto, Pushto

8083
8084 Portuguese
8185 Quechua

Rhaeto-Romance

8277
8279 Romanian
8285 Russian
8365 Sanskrit
8368 Sindhi

Serbo-Croatian

8372
8373 Singhalese

Code Language

8375 Slovak
8376 Slovenian
8377 Samoan
8378 Shona
8379 Somali
8381 Albanian
8382 Serbian
8385 Sundanese
8386 Swedish
8387 Swahili
8465 Tamil
8469 Telugu
8471 Tajik
8472 Thai
8473 Tigrinya
8475 Turkmen
8476 Tagalog
8479 Tonga
8482 Turkish
8484 Tatar
8487 Twi
8575 Ukrainian
8582 Urdu
8590 Uzbek
8673 Vietnamese
8679 Volapük
8779 Wolof
8872 Xhosa
8979 Yoruba
9072 Chinese
9085 Zulu

54

D4753S P36-60.p65 2003/03/13, 11:3254

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Warning and Instruction Displays

These displays will alert you to a missed operation or provide further instructions.

PLEASE SET CLOCK BY
PRESSING ACTION KEY

PLEASE PREPARE FOR TIMER
REC

CHECK CASSETTE
RECORD TAB

NO CASSETTE

TO CANCEL TIMER REC
HOLD DOWN STOP KEY
FOR APPROX 3 SEC

VIDEO HEADS MAY NEED
CLEANING PLEASE INSERT
HEAD CLEANING CASSETTE
OR REFER TO MANUAL

END : PLAY

VCR LOCK ACTIVATED

REMOTE CONTROL IS SET
TO CABLE/DSS MODE
USE VCR : VCR KEY
USE DVD : DVD KEY

REMOTE CONTROL IS SET
TO TV MODE
USE VCR : VCR KEY
USE DVD : DVD KEY

PLEASE CHECK THE DISC,
AND FOR STAINS OR
SCRATCHES ON DISC

THIS DISC MAY NOT BE PLAYED
IN YOUR REGION

THIS TYPE OF DISC CANNOT BE
PLAYED. PLEASE INSERT A
DIFFERENT DISC

CANNOT PLAY THIS FILE

THIS FILE IS PROTECTED

IT IS PROHIBITED TO COPY
DVD/VIDEO CD/CD TO VHS

CautionOSD

If you attempt to set or review a Timer
Recording and the Clock is not set...

If DECK is not in Stop mode or a cassette with
record tab is not inserted 2 minutes before a
Timer Recording is about to begin...

If you press REC on the remote control or DECK,
and a cassette is inserted with no record tab...

If you press PLAY, FF, REW, or REC on the
remote control or DECK without a cassette
inserted...

If you press STOP or POWER during a Timer
Recording...
(visible in VCR mode only)

If head cleaning becomes necessary while
playing back a tape...

If you press a function button other than STOP/
EJECT or POWER while DECK is
in VCR Lock mode...

If you press an invalid key on the remote while
in CABLE/DSS mode...

If you press an invalid key on the remote while
in TV mode...

If you press PLAY, and DECK reads data from a
stained or scratched disc in DVD mode.

Playback of a disc with different region number
was attempted. Only discs marked region “1”,
“ALL”, or those that include “1” are playable on
this DECK.

An unusable disc is inserted in the DECK.

This file format cannot be played.
(Appears during MP3/WMA/JPEG file playback)

This file is copyright protected and cannot be
played back. (Playback is prohibited.)
(WMA only)

If you press REC in DVD mode...

Page

24

24
25

6

20
21

25

6

33

28
29
34

28
29
34

4

3

4

45

45

21

Information

For Your

D4753S P36-60.p65 2003/03/13, 11:3255

55

Before Requesting Service

Check the following points if you are having trouble with your DECK.

Power

No power…

Power turns itself off...

Recording & Playback

TV program cannot be recorded...

Timer recording cannot be
performed…

There is no playback picture, or the
playback picture is noisy or contains
streaks...

During special effects playback,
picture may contain some vertical
jitter when using a TV with an
Automatic Vertical Hold Control...

DECK cannot be controlled...

Remote Control

DECK cannot be remote controlled...

PROG buttons do not respond...

Correction

• Completely insert Power Plug into an AC outlet.

• Set POWER button to on.

• Make sure power source is active.

• Auto power-off (shutoff) occurs after about 5 min.

in DVD mode with no operation, or if there is no
broadcast signal in TV or Playback mode.
Turn the power back on. (pp. 23, 33)

Correction

• Check connections between DECK, external
antenna, and TV.

• Check channel selections.

• Make sure your antenna system (CABLE or TV) is

correctly set. (Channels [p. 18])

• Make sure cassette record tab is intact. (p. 6)

• Confirm that clock is set to current time and date.

• Make sure Cable/DSS box (if used) is left on and

tuned to channel to be recorded.

• Set recording start/stop times correctly. (p. 24)

• Timer recording may not be performed or continued

if a power interruption occurs before or during a
Timer Recording, even after power is restored.

• Select channel 3 or 4 on TV to match VCR output
channel (3 or 4) (p. 16) or select LINE.

• Set VCR/TV selector to “VCR.”

• Adjust TRACKING control in either direction. (p. 6)

• Try Head Cleaning. (p. 6)

• Set TV’s Vertical Hold Control to MANUAL, then

adjust.

• Make sure DECK power is on.

• Check Remote batteries.

• Make sure VCR LOCK is set to off. (p. 33)

• Make sure Remote is in proper mode. (p. 28)

• Make sure Timer Recording is not in progress.

Correction

• Make sure DECK power is on.

• Make sure Remote is in VCR mode.

• Aim Remote Control directly at remote sensor on DECK. (p.9)

• Avoid any object blocking signal path.

• Check Remote batteries. (p. 4)

• Exposing DECK remote sensor to direct fluorescent

or outdoor light may cause signal interference.

• PROG functions are not available in COMPONENT
Video Output and S-VIDEO OUT. Set TV to either RF
IN or VIDEO IN. (p. 10)

• Check Remote batteries. (p. 4)

• Press VCR or DVD button for DVD/VCR mode. (p. 28)

56

D4753S P36-60.p65 2003/03/13, 11:3256

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Check the following points if you are having trouble with your DECK.

DVD/ Video CD/ CD

Play fails to start even when PLAY is
pressed...

Play starts but then stops immediately...
Picture is distorted during rapid

advance or rapid reverse...
No Forward/Reverse Scene Search

play...
Play does not start even when title is

selected...
Audio soundtrack and/or subtitle

language is not the one selected at
the initial settings...

No subtitles...

Alternative audio soundtrack
(or subtitle) language cannot be
selected...

Angle cannot be changed...

Miscellaneous

Programs cannot be viewed on TV...

Video cassette cannot be inserted...

Video cassette ejects when
a recording is started or the power is
turned off for timer recording...

In Stop mode, the motor (CYLINDER)
continues to rotate...

The disc cannot be removed..

Correction

• This DECK cannot play discs other than DVDs,
Video CDs and CDs.

• The disc may be dirty and require cleaning.

• Be sure disc is installed with label side up.

• The picture will be somewhat distorted at times:

this is normal.

• Some discs may have sections which prohibit
Forward/Reverse Scene Search. (p. 23)

• Confirm the “DVD LOCK” setting. (p. 48)

• If the audio soundtrack and/or subtitle language

selected at DVD initial settings does not exist
on the disc, it will not be accessible.

• Subtitles appear only when available on disc.

•“OFF” is selected at the changing subtitle

language. Select “ON” at the “Subtitle Languages”
section (p. 36) to display the subtitles.

• Alternative language cannot be selected with discs
which do not contain more than one language.

• For some discs, alternative language cannot be
selected with the AUDIO or SUB TITLE button.
Try selecting it from the DVD MAIN MENU if available.

• This function is dependent on software availability.
Even if disc has multiple angles, they may be
recorded for specific scenes only (ANGLE
indicator on DECK lights up). (p. 37)

Correction

• Make sure TV is set to output of DECK.

• Check connections between DECK,

external antenna, and TV.

• Set VCR/TV selector to “TV.” (p. 21)

• Make sure proper signal source is selected.

• Insert the cassette with window side up; record

tab facing you.

• Make sure cassette record tab is intact. (p. 6)

• To enable Quick play mechanism, the cylinder will

rotate for about 3 minutes. This reduces response
time from Stop to Play mode.

• First, unplug DECK. Then, prepare a rigid wire

(e.g. an extended paper clip) and, applying
moderate force, insert it straight into the hole at the
base of the tray. The tray will eject a little. Now, pull
the tray all the way out and remove the disc. (p. 9)

Information

For Your

If you cannot resolve the problem, please call the Customer Call Center for product
assistance at 1-800-211-PANA (7262).
To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).
or send e-mail to : [e-mail]

D4753S P36-60.p65 2003/03/13, 11:3257

57

Limited Warranty

PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC
CORPORATION OF AMERICA
One Panasonic Way
Secaucus, New Jersey 07094

PANASONIC SALES COMPANY,
DIVISION OF MATSUSHITA
ELECTRIC OF PUERTO RICO, INC.,
AVE. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park
Carolina, Puerto Rico 00985

Panasonic DVD/VCR Deck Limited Warranty

Limited Warranty Coverage

If your product does not work properly because of a defect in materials or workmanship, Panasonic
Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)
will, for the length of the period indicated on the chart below, which starts with the date of original purchase
(“Limited Warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b)
replace it with a new or a refurbished product. The decision to repair or replace will be made by the
warrantor.

Product or Part Name

DVD/VCR Deck
Rechargeable Batteries

(in exchange for defective item)

During the “Labor” Limited Warranty period there will be no charge for labor. Dur ing the “Parts” warranty
period, there will be no charge for parts. You must mail-in your product dur ing the warranty period.
If non-rechargeable batteries are included, they are not warranted. This Limited Warranty only applies to
products purchased and serviced in the United States or Puerto Rico. This Limited Warranty is extended
only to the original purchaser and only covers product purchased as new. A purchase receipt or other
proof of original purchase date is required for Limited Warranty service.

Parts

One (1) Year

Ten (10) Days

Labor

Ninety (90) Days

Not Applicable

Mail-In Service

For assistance in the continental U.S.A. in obtaining repairs please ship the product to:

For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax [phone].
When shipping the unit carefully pack and send it prepaid, adequately insured and preferably in the original

carton. Include a letter detailing the complaint and provide a day time phone number where you can be
reached.

IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY PERIOD THE PURCHASER WILL BE
REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF
PURCHASE, AMOUNT PAID AND PLACE OF PURCHSE. CUSTOMER WILL BE CHARGED FOR THE
REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.

D4753S P36-60 (030610 –§”Ô•Ï•X).p65 2003/06/10, 18:5558

Panasonic Services Company
Customer Servicenter
Suite B
4900 George McVay Drive
McAllen, TX 78503

58

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Limited Warranty Limits And Exclusions

This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES
NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT
COVER damages which occurred in shipment, or failures which are caused by products not supplied
by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling,
misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls,
improper maintenance, power line surge, lightning damage, modification, or commercial use (such as
hotel, office, restaurant, or other business), rental use of the product, or service by anyone other than
a Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY
COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having

someone remove or re-install an installed unit if applicable, travel to and from the servicer, loss of or
damage to media or images, data or other recorded content. The items listed are not exclusive, but
are for illustration only.)

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied Limited Warranty lasts, so the exclusions may not apply to you.

This Limited Warranty gives you specific legal rights and you may also have other rights which vary
from state to state. If a problem with this product develops during or after the Limited Warranty period,
you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then
write to the warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.

PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR
RESPONSIBILITY.

Customer Services Directory

For Product Information, Operating Assistance, Literature Request, Dealer Locations, and

Customer Services DirectoryCustomer Services Directory

Customer Service inquiries please visit Web Site:

http://www.panasonic.com

You can purchase parts, accessories, locate your nearest servicenter and more by visiting our Web Site

or E-mail us via web:

http://www.panasonic.com/consumer_electronics/support/customerfeedback.asp

Contact:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.

For hearing or speech impaired TTY users, TTY : 1-877-833-8855

Accessory Purchases

1-800-332-5368 (Customer Orders Only)
1-800-237-9080 (Fax Only)

(Monday-Friday 9 am-8 pm, EST.) Panasonic Services Company
20421 84th Avenue South, Kent, WA 98032
(Accepts Visa, MasterCard, Discover Card, American Express, and Personal Check)

http://www.pasc.panasonic.com or email to [e-mail]

For hearing or speech impaired TTY users, TTY : 1-866-605-1277

Service in Puerto Rico

Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Phone [phone] Fax [phone]

As of May 2003

D4753S P36-60 (030610 –§”Ô•Ï•X).p65 2003/06/10, 18:5559

Information

For Your

59

Spanish Quick Use Guide/ Guía para rápida consulta

DST :

ON

6 / 8 / 2003 SUN 2: 2 0 PM

SET COMPLETE

D

- - - - - - - - -- - - - - - - -- - - - - -

SET CLOCK

DST : O

N

SELE CT MONTH

1 / /

:

SELECT :
SET :SET
EXIT

: ACT I ON

- - - - - - - - -- - - - - - - -- - - - - -

SET CLOCK

AUTO CLOCK SET IS
I NCOM

PLETE

PLEASE SET CLOCK BY
PRESSING

ACT I ON KEY

6 / 8/ 20 03

SUN 2 : 20P

M

DST :

ON

SETT I NG

: CH

10

AUTO CLOCK SET

COMPLETED

CONEXIONES/CONFIGURACION INICIAL (READY TO PLAY)

Para ajustar el idioma, canal yPara ajustar el idioma, canal y

Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA.

El DVD/VCR iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA.

CONEXIONES

Para Ant/Cable

Conecte el cable de la antena al terminal IN

1

FROM ANT del DVD/VCR.
Conecte el terminal OUT TO TV del DVD/VCR

2

a la entrada de la antena VHF/UHF del TV con

➛➛

DVD/VCR

➛

➛➛

➛➛

➛

➛➛

TV

Televisor

el cable RF incluido.

Para Sistema Digital de Satelite (DSS)/ Convertidor de cable

Conecte la salida de convertidor de cable

1

al terminal IN FROM ANT.
Conecte el terminal OUT TO TV del DVD/VCR

2

a la entrada de la antena VHF/UHF del TV con
el cable RF incluido.

CONFIGURACION INICIAL

Encienda el TV y cambie al canal 3.

1

Enchufe el cable de CA.

2

El DVD/VCR se encenderá e iniciará las
fijaciones de los canales y del reloj.

• Si no aparece la pantalla de abajo, compruebe
la conexión del DVD/VCR-TV y si el canal del
TV está a 3, intennte cambiando al canal 4.

• Para cambiar el canal de salida del DVD/VCR,
consulte las instrucciones de “Canal de salida
del VCR” (informaciones en inglés página 19).

Enchufe el cable de CA.

Televisor

VHF/UHF

Las fijaciones se realizan automáticamente.

3

Cuando termina las fijaciones, aparecerá la
siguiente pantalla.

Si aparece en la pantalla “AUTO CLOCK SET IS
INCOMPLETE (FIJACION AUTOMATICA DEL
RELOJ ES INCOMPLETO)”, Ajuste el reloj
como se describe a continuación.

DVD/VCR

VHF/UHF

➛➛

➛ DVD/VCR

➛➛

DVD/VCR

2

2

Terminal
OUT TO TV

Terminal
OUT TO TV

Terminal
IN FROM ANT.

Terminal IN FROM ANT.

Entrada (IN) desde

1

ANT./CABLE

➛➛

➛ TV

➛➛

Estuche convertidor
de TV por cable

Entrada (IN) desde
ANT./CABLE

1

CH AUTO SET PROCEEDING

CANCEL : STOP

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

Al inicio, el idioma de la
pantalla está fijado a
inglés.
Para cambiar el idioma,
seleccione la pantalla
MENU (informaciones en
inglés página 18).

Si está usanndo un convertidor de TV por cable y
en su area hay un canal de Public Broadcast
Station (PBS), ajuste su convertidor al canal PBS
de su area. Si está usando un receptor DSS, este
debe estar apagado.

Nota

• Los botones de funciones no funcionan durante
la configuración inicial.

• Para retirar un cassette durante el ajuste
automático, presione EJECT en el control remoto
o STOP dos veces en el aparato. En este caso,
los ajustes de los canales y la hora se deben
hacer manualmente. Para los ajustes seleccione
la pantalla MENU (informaciones en inglés
página 18).

• Dependiendo de las condiciones, el ajuste
automático puede durar más de 30 minutos.
En ese caso, presione STOP para detener el
ajuste automático y realice los ajustes
manualmente en la pantalla MENU.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

60

D4753S P36-60.p65 2003/03/13, 11:3260

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [e-mail]

AJUSTE MANUAL DEL RELOJ

Si la fijación ha sido incompleta.

Presione la tecla ACTION en el control remoto

1

para visualizar la pantalla del menú SET
CLOCK.

Presione para seleccionar el mes y SET

2

para ajustar. De la misma forma, seleccione y
ajuste la fecha, año, hora y DST (hora de
verano).

Presione dos veces la tecla ACTION para

3

poner el RELOJ en marcha y salir.

PRECAUCIÓN

Al usar cables coaxiales RF del tipo “tuerca”,
apriételos solamente con los dedos. Un apriete
excesivo puede dañar los terminales.

Operaciones básicas para la reproducción

Inserte un cassette,

1

• La alimentación del DECK se activa.
En la Pantalla de Visualización Multi
Función se ilumina “VCR”.

Presione PLAY para reproducir el cassette.

2

• Si el cassette no tiene la lengüeta de
prevención de grabación (página 6), se
inicia la reproducción automáticamente.

Detalles especiales durante la grabación

Presione FF/SLOW+ o REW/SLOW- para

búsqueda de escenas hacia delante/ hacia
atrás. Presione PLAY para liberar. Durante
la búsqueda, cada vez que presione FF o
REW se cambia la velocidad como sigue:
[SLP] aprox. 21X
[LP] aprox. 9X
[SP] aprox. 7X

↔↔

↔ aprox. 9X

↔↔
↔↔

↔ aprox. 7X

↔↔
↔↔

↔ aprox. 3X

↔↔

Si la imágen se interrumpe con la velocidad de
21X, 9X o 7X, cambie la velocidad a 9X, 7X o
3X.
Presione PAUSE/STILL para imagen Fija
(Congelada).

Presione PLAY para liberar.
Presione PAUSE/STILL en el modo de

imagen fija para imágenes cuadro a cuadro.

Presione PLAY para liberar.
Presione FF/SLOW+ o REW/SLOW- en el

modo de imagen fija para cambiar la
velocidad de las imágenes a cámara lenta.

Presione STOP para detener el cassette.

3

Presione REW/SLOW- o FF/SLOW+ en el

modo de parada para rebobinado/avance
rápido del cassette.
Presione EJECT en el control remoto,
o STOP/EJECT en el DECK para expulsar
el cassette.

Operaciones básicas para la grabación

Inserte el cassette con lengüeta de

1

protección de grabación (página 6).

Presione CH / , o las teclas de números

2

para seleccionar el canal.

Presione SPEED para seleccionar la

3

velocidad de grabación (página 6)

• SP = Reproducción estándar,

• LP = Larga duración,

• SLP = Superlarga duración.

Presione REC para comenzar a grabar.

4

• Para eliminar escenas indeseadas, presione
PAUSE/STILL para hacer una pausa, y al
presionar nuevamente continua la grabación.

• No podrá ver otro canal durante la
grabación.

Presione STOP para detener la grabación.

5

Programación fácil para la
grabación con temporizador

Presione PROG

1

para visualizar la pantalla de Programacion.

I

N I C I

O

FECHA

2

7 SAB

SLP

HOY

ELEGIR FECHA DE I N I C I O

ELEGIR
FIJAR
TERMINAR

PARADA

--:-- --:-- --

:

:SET

:

PROG

Orden para elegir

Ejemplo

Fecha de hoy

2) Para ajustar los ítems que quedan,
presione para seleccionar y presione SET

para ajustar los tiempos de INICIO/PARADA,
CANAL, o entrada de LINEA (página 35), y
velocidad del cassette (SP, LP, SLP).
Presione PROG para finalizar PROGRAM.

FE

I N I C

7

2 : 00 P 3 : 20 P

-- -- : --

--

-- : --

-- : --

--

CANC

ELAR: ADD / DLT

ELEGIR 1- 8 :

: SET

ENTRAR
SAL I R

: PROG

PARADA CA VEL

-- : -- --

-- : -- --

-- : -- --

3

Grabación de un toque

Presione REC repetidamente para ajustar la

hora de grabación (30 min - 4 horas).

• La videograbadora termina la grabación

a una hora programada.

Grabación normal

1) Para ajustar la FECHA de

C

A

grabación, presione

para seleccionar:
1-31 = una vez, o
DIARIO = a la misma hora
de lunes a viernes, o
SEMANA = a la misma
hora cada semana y
presione SET para ajustar.

1

31

/ Orden para elegir

7

SEMANAL

Presione

02 SLP

--

para seleccionar un número

--

--

que no está usando para
ingresar mas programas y

presione SET

(

SAB

SEMANAL

(

LUN

)

para ajustar.
Luego repita el paso 2.
O

Presione nuevamente
PROG para salir.

0:30 1:00

1:302:003:004:00

)

2

SEMANAL

(

DOM

68 9

DIARIO

)

Guía para rápida

consulta

61

D4753S P36-60.p65 2003/03/13, 11:3261

Spanish Quick Use Guide/ Guía para rápida consulta

GRUPO

: 1 DVD-AUDIO

P I STA

: 1 00: 12 : 34

ENTRAR: 0

-

9

FI JAR : SET

TERMINAR

: DISPLAY

ELEGI R:
FI JAR : SET SIGUI ENTE: DI SPLAY

T ITULO : 12 DVD
CAPI TULO: 24 00:12:34

PI STA : 17 VIDEO CD
PBC : I NACTIVO 00 :12 : 34

FI JAR : SET SIGUI ENTE: DI SPLAY

Operaciones básicas del DVD

Presione

1

aparato.

Presione

2

1) Presione

3

2) Ponga un disco en la bandeja de disco.

• Sujete el disco sin tocar ninguna de sus
superficies, póngalo con el lado donde esté
impreso el título hacia arriba, alinéelo con las
guías y póngalo en su posición apropiada.
Disco de 3” (8 cm) / Disco de 5” (12 cm)

Presione

4

La bandeja del disco se cierra
automáticamente.

• Si está usando un DVD interactivo (Interactive
DVD) o un Vídeo CD con contol de
reproducción (playback control) y aparece un
menú de títulos (TITLE MENU) en la pantalla,
siga al paso 5.

Presione o las teclas numéricas para

5

seleccionar el artículo deseado.

Presione
Si usa las teclas numéricas, la
reproducción comienza automáticamente.

Presione

6

Presione

7

■ Para buscar una escena particular
Búsqueda hacia adelante

Presione

Búsqueda hacia atrás

Presione
(Para liberar, presione

■ Para saltar un capítulo o una pista
Salto hacia adelante

Presione

Un capítulo (Vídeo DVD) o una pista (Audio
DVD/Vídeo CD/CD) se salta cada ves que se
oprime la tecla.

Salto hacia atrás

Presione l

■■

■ Para ver una imagen fija

■■

Presione
(Para liberar, presione

■ Para ver imágenes cuadro a cuadro
(DVD/Vídeo CD)
Presione

La imagen avanza un cuadro cada vez que
presiona la tecla. (Para volver a la
reproducción normal, presione

■ Para ver en cámara lenta (DVD/Vídeo CD)
Presione

de imagen fija.
(Para liberar, presione

POWER

DVD

SET o PLAY

OPEN/CLOSE

FF/SLOW+

REW/SLOW-

SKIP

PAUSE/STILL

PAUSE/STILL

FF/SLOW+

en el control remoto o el

para seleccionar el modo DVD.

OPEN/CLOSE

PLAY

para iniciar la reproducción.

.

para la reproducción.

STOP

para parar la reproducción.

para expulsar el disco.

en el modo de reproducción.

en el modo de reproducción.

PLAY

)

l en el modo de reproducción.

SKIP

en el modo de reproducción.

durante la reproducción.

PLAY

)

en el modo de imagen fija.

o

REW/SLOW-

PLAY

)

PLAY

)

en el modo

Funcionnamiento del DVD utilizando
visualizaciones en pantalla

Cuando se presiona DISPLAY, la visualización en
pantalla muestra la información del disco (título / capítulo
/ número de lista, tiempo transcurrido de reproducción,
audio / idioma del subtítulo, y ángulo) e información
(repetir la reproducción, modo reproducción, Karaoke
vocal encendido / apagado, etc.).

Presione

1

o parada para visualizar las visualizaciones en
pantalla.

• Cada vez que se presione

visualización en pantalla cambia como se
muestra a continuación.

Presione (o ) para seleccionar el ítem

2

deseado.

Presione
Presione para seleccionar el ajuste

3

deseado.

Presione
Para volver a la pantalla normal,
Presione repetidamente

<Ejemplo (Vídeo DVD)>

<Ejemplo (Vídeo CD)>

<Ejemplo (Audio DVD)>

DISPLAY

Información seleccionada del disco

Información seleccionada del DECK

en el modo reproducción

DISPLAY

➡

➡

,la

Pantalla normal

SET

para ajustar.

SET

para ajustar.

CLEAR o DISPLAY

T ITULO : 12 DVD

CAPI TULO: 11 00:12:34

ELEGI R:
FI JAR : SET SIGUI ENTE: DI SPLAY

PI STA : 12 VIDEO CD

PBC : I NACTIVO 00 :12 : 34

FI JAR : SET SIGUI ENTE: DI SPLAY

GRUPO

: 1 DVD-AUDIO

P I STA

: 1 00: 12 : 34

ELEGI R:

TERMINAR

FI JAR : SET

: DISPLAY

.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

62

D4753S P36-60.p65 2003/03/13, 11:3262

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [e-mail]

Fijaciones iniciales

Presione DVD para seleccionar el modo DVD.

1

Presione ACTION en el modo de parada para

2

visualizar MENU.

Presione para seleccionar el artículo deseado.

3

Presione

IDIOMAS DEL DISCO

Todos los idiomas ofrecidos en el disco pueden ser
ajustados. Si el idioma ajustado no es ofrecido en el
disco, se seleccionará el idioma original del disco.

SALIDA DE AUDIO

Puede usted ajustar la salida audio procedente del
terminal de salida audio digital.

DETENER RASTREO

Para seleccionar “CAMPO” o “CUADRO fijo” para prevenir
inestabilidad o para permitir ver textos pequeños o
patrones finos claramente en el modo de imagen fija.

TV PREFERENCIA

Para seleccionar cuando el material del vídeo es para
pantalla ancha y se quiere reproducir en el estilo
Pan&Scan, en el estilo Letterbox o en el estilo 16:9 en
la pantalla.

Presione para seleccionar el artículo deseado.

4

Presione
Volver a visualizar el menú de DVD para

5

continuar el ajuste.
Presione
ajuste o, para salir, presione

SET

.

SET

.

ACTION

y pase al paso 3 para ajustar otro

ACTION

tres veces.

Cambio del idioma de subtítulos
[Vídeo DVD solamente]

EI idioma de los subtítulos seleccionado al hacer las
fijaciones iniciales se puede cambiar por otro idioma
diferente, si éste se encuentra disponible.

1

ELEGIR :
ACTIVO / INACTIVO :
TERMINAR : SUB TITLE

2

ELEGIR :
ACTIVO / INACTIVO :
TERMINAR : SUB TITLE

Presione

la reproducción.
Cuando no haya subtítulos
grabados, se visualizará “-” en
lugar del número de idioma.

Presione para
seleccionar el idioma deseado.
Presione para
seleccionar “ACTIVO” o
“INACTIVO.”

SUBTITLE

durante

Selección de vocal para los
discos de Karaoke [DVD/Vídeo CD]

Presione

1

para visualizar la pantalla AUDIO.

2

ELEG I R:
TERMI

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF

• Video CD LR L R

NAR : AUDIO

AUDIO

durante la reproducción

Presione (o )
para seleccionar el ajuste
deseado.
Presione (o ) para
ajustar. (DVD solamente)

Selección de IDIOMAS DEL
DISCO [DVD solamente]

Seleccione “AUDIO”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonesa :
Original : Se seleccionará el idioma

OTRO

original de cada disco.

✱✱✱✱

:Se puede seleccionar el otro

idioma.

Seleccione “SUBTITULO”

AUTO : Se seleccionará el mismo que fue

• Si el idioma seleccionado en la preparación

• Si se utiliza otro idioma durante la

Inglés / Español / Francés / Japonesa :
OTRO

seleccionado en la preparación de
“AUDIO”. (Fijación de fábrica)

de “AU DIO ” se utiliza durante la
reproducción, los subtítulos no aparecerán.

reproducción, los subtítulos aparecerán en el
idioma seleccionado en la preparación de
“AUDIO”

✱✱✱✱

:Se puede seleccionar el otro

idioma.

Seleccione “MENU”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonesa :
OTRO

✱✱✱✱

:Se puede seleccionar el otro

idioma.

Visión desde otro ángulo
[DVD solamente]

Algunos discos DVD tienen escenas que han sido
filmadas simultáneamente desde ángulos diferentes.
Con estos discos, la misma escena podrá verse desde
cada uno de estos ángulos diferentes utilizando el botón
ANGLE.

ANGULO

1

2

ELEGIR :

ANGULO

ELEGIR :

: 1

: 2

Presione

reproducción para visualizar
la selección del ángulo.

Presione para
seleccionar el ángulo
deseado.

ANGLE

durante la

Cambio del idioma de la pista
de sonido [DVD solamente]

EI idioma de la pista de sonido seleccionado al hacer
las fijaciones iniciales se puede cambiar por otro
idioma diferente, si éste se encuentra disponible.

1

ELEG I R:
TERMI

NAR : AUDIO

2

ELEG I R:
TERMI

NAR : AUDIO

Presione

durante la reproducción
para visualizar
SONIDO en la pantalla.

Presione para
seleccionar idioma.

AUDIO

63

Guía para rápida

consulta

D4753S P36-60.p65 2003/03/13, 11:3263

Spanish Quick Use Guide/ Guía para rápida consulta

Utilización de un menú de títulos
[DVD solamente]

Algunos discos con películas, vienen con dos o más
títulos. Por ejemplo, si el disco tiene un menú de
títulos grabados, el botón TITLE podrá utilizarse
para seleccionar el título de la película.

Presione

1

Ahora se visualiza una lista de los títulos del
disco.

2

TITLE

T I TLE MENU

Cas t l es

Dogs

Love

r

s

Dogs

of the world

<ejemplo>

durante la reproducción.

Presione o las
teclas de números para

B

i r

seleccionar el título

ds

deseado.

Presione

SET

para elegir.

Utilización de un menú de DVD
[DVD solamente]

Algunos discos DVD ofrecen un menú especial.
Este menú incluye guías para contenidos únicos,
audio, subtitulos, idiomas, etc. Aunque los
contenidos y las operaciones se cambian, los
siguientes son unos pasos básicos para el uso del
menú.

Presione

1

El menú de DVD introducido en el disco se
visualiza ahora.

DVD MENU

2

1 . SUBT I TLE
2 . AUD

3 . ANGLE

MENU

I

O

<ejemplo>

durante la reproducción.

Presione o las
teclas de números para

seleccionar el ítem deseado.

Presione

SET

para elegir.

Ampliación de la imagen [Vídeo DVD solamente]

Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar la
relación de zoom usando el botón ZOOM.

Presione

tamaño de la imagen como se indica a continuación:

■ Use los botones , , y para desplazar

ZOOM

repetidamente para cambiar el

la posición hacia arriba, hacia abajo, hacia la
izquierda o hacia la derecha.

2da

3da

Funcionamiento de la ejecución de MP3/WMA/JPEG

Puede utilizar esta unidad para reproducir audio de
formato MP3/WMA/JPEG, grabado para uso personal
con una computadora, etc., en un CD-ROM o CD-RW.
La ejecución no podrá realizarse en algunos casos,
debido a las condiciones de la grabación.

Presione

1

Presione

2

coloque un disco MP3/WMA/JPEG en la bandeja

POWER

en el control remoto o DECK.

OPEN/CLOSE

y a continuacion

de discos.

Presione

Se visualizará el MENU MP3/WMA/JPEG y la

3

ejecución se iniciará automáticamente. (Se

OPEN/CLOSE

para cerrarla.

visualizará el directorio del CD.)

<ejemplo>

Estado de la
función

Area de las
carpetas

(La carpeta
visualizada
actualmente se
volverá verde)

:Archivo MP3 :Archivo WMA :Archivo JPEG

:Carpeta :Carpeta principal

64

REPROD

ROOT . .

VA

END_W

TECHNO

POPS

NOCTURNE

J

AZZ

NORN

MODE DE REPRODUCCION:
NORMAL

MODO DE REPRODUCCIÓN

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [e-mail]

DD_

ALTZ

CUB I C

00 : 00 :

00

(El archivo/ la
carpeta se
visualiza con
un cursor.)

Contador
Carpeta

principal
Area de

archivos

■ Ejecución MP3/WMA/JPEG (Durante el modo STOP)

Presione para seleccionar un archivo MP3/WMA

4

5

/

) o un archivo JPEG ( ), y presione

(

PLAY

.

• MP3/WMA

Búsqueda hacia adelante/hacia atrás

➡Presione

Salto de pista hacia adelante/hacia atrás

➡Presione

• JPEG

Búsqueda siguiente/anterior

➡Presione

Inicie la muestra-diapositiva

➡Presione

Ampliar una imagen ➡ Presione
Girar una imagen ➡ Presione

Presione

■ Seleccione MODO DE REPRODUCCION

(Durante el modo STOP)

Presione para mover el cursor a MODO DE
REPRODUCCION, y Presione

MODO DE REPRODUCCIÓN deseado.

[MODO DE REPRODUCCIÓN]
NORMAL: Todos los archivos se reproducen sólo una vez
REPETICION DE UNA MUSIC:

El archivo seleccionado se reproduce repetidamente.
REPETICION DE UN ARCHIVO:
Los archivos que se encuentran en la carpeta
seleccionada se reproducen repetidamente.
REPETICION DEL DISCO:
Todos los archivos se reproducen repetidamente.

Presione

PRINCIPAL.

FF/SLOW+

SKIP

STOP

ACTION

o

REW/SLOW-

| o |

SKIP

| o |

FF/SLOW+

o

para detener la operación descrita arriba.

para regresar al DVD MENU

durante la ejecución.

SKIP

durante la ejecución.

SKIP

REW/SLOW-

ZOOM

ANGLE

para seleccionar el

.

.

.

SET

.

o

D4753S P36-60.p65 2003/03/13, 11:3264

Configuración de los altavoces

Presione

1

aparato.

Presione

2

SAL I DA PARA ALTAVOCES :

3

MULT

TAMAÑO DEL ALTAVOZ
BALANCE DE SAL
T

I EMPO ATRAZADO

ELEG
F

I

TERM

Presione para seleccionar, y presione

4

SET

■ SALIDA PARA ALTAVOCES

■ TAMAÑO DEL ALTAVOZ

■ BALANCE DE SALIDA

■ TIEMPO ATRAZADO

Presione

5

para salir.

POWER

DVD

AJUSTE DE ALTAVOCES

I

DA

I

R:

JAR : SET

I

NAR : ACTION

en el control remoto o el

para seleccionar el modo DVD.

Presione para

seleccionar “AJUSTE DE

I -

CANALES

ALTAVOCES,” y

Presione

SET

visualizar la pantalla
AJUSTE DE ALTAVOCES.

para fijar.

Fije el número de altavoces conectados al DECK.

MULTI-CANALES (Predeter minado en fábrica)

Cuando están conectados 3 o más altavoces.

2 CANALES

Cuando están conectados 2 altavoces.

Se determinan las propiedades de frecuencia del
altavoz y la existencia de los altavoces.

FRENTE (GRANDE [predeterminado en fábrica]/

PEQUEÑO)

CENTRO (GRANDE [predeterminado en fábrica]/

ENVOLVENTE (GRANDE [predeterminado en

SUBWOOFER (ENCENDIDO [ predeterminado en

Ajuste la salida de nivel de volumen para los altavoces.

CENTRO, ENVOLVENTE(DER)/(IZQ), SUBWOOFER

SEÑAL PRUEBA

Configurar el tiempo atrazado. Da a la salida de
sonido un efecto retrasado que le ofrece la ilusión de
encontrarse en la posición de escucha ideal.

PEQUEÑO/NINGUNO)

fábrica]/PEQUEÑO/NINGUNO)

fábrica]/APAGADO)

-6db ~ +6db (0db: predeterminado en fábrica)

El sonido de prueba es la salida en sentido de las
manecillas del reloj.

ACTION

tres o cuatro veces

para

D4753S P36-60.p65 2003/03/13, 11:3265

Guía para rápida

consulta

65

INDEX

DECK & VCR

A ACTION button ................................. 8, 18

Accessories............................................ 4

ADD/DELETE button

(Add or Delete a Channel) ............ 8, 19

Audio Broadcast types

(Stereo/SAP/Mono) ............................ 26

Audio Mode (Playback, Recording) .... 27

Auto Operation Functions .................... 31

Auto Shut-Off ........................................ 33

B Batteries ................................................. 4

C Channel (“SET UP CHANNEL”) .......... 18

Channel Up/Down,

Tracking/V-Lock Button .................... 6, 8

Clock (“SET CLOCK”) .......................... 18

Commercial Skip ................................. 31

Connections................................. 12 ~ 15

Copy Your Tapes (Dubbing) ............... 35

COUNTER RESET button ............... 8, 32

Customer Services Directory............... 59

D DISPLAY button ............................... 8, 11

DSS/CABLE mode button ............... 8, 28

DST (Daylight Saving Time) ................ 19

E EJECT button ................................... 8, 20

ENTER button

(For tuning TV Channel) ................ 8, 28

F FAST FORWARD/SEARCH button .. 8, 20

H Head Cleaning ...................................... 6

I Index Search ........................................ 30

Indicator (Multi Function Display) ....... 11

Initial Setup (Ready to Play) ......... 16, 17

INPUT button ................................... 8, 35

L Limited Warranty ........................... 58, 59

Location of Controls

(Remote, DECK) .......................... 8 ~ 10

MMulti-Brand Control ....................... 28, 29

O On-Screen Displays (VCR) ................. 11

One Touch Recording ......................... 21

P PAUSE/STILL button (Still Picture) .. 8, 20

PLAY button (Playback a Tape) ...... 8, 20

POWER button ....................................... 8

PROG button (PROGRAM).............. 8, 24

Program Clear, Review, Replace ....... 25

Program End Search ........................... 30

Q Quality Picture ....................................... 6

R REC button (Record on a Tape) ..... 8, 21

Record Tab ............................................ 6

Remote Sensor ...................................... 9

Remote Warning .................................. 34

Repeat Play ......................................... 32

Reset All Memory Functions ................. 9

REWIND/SEARCH button ............... 8, 20

S SAP/Hi-Fi ............................................. 27

SEARCH

(Index and Program End Search) ..... 30

SLOW+/SLOW- button

(Slow Motion Picture) .................... 8, 20

Spanish Quick Use Guide ........... 60 ~ 65

Specifications......................................... 7

SPEED button .................................. 8, 21

Still (Freeze) Picture ............................ 20

STOP button ..................................... 8, 20

T Tape Position, Tape Status ................. 34

Timer Recording .................................. 24

Trouble Shooting ........................... 56, 57

TV mode button................................ 8, 28

V VCR Lock ............................................. 33

VCR mode button ............................ 8, 28

VCR/TV button ................................. 8, 21

VCR/TV Selector Feature .................... 32

VOLUME +/- button (TV Volume) .... 8, 28

WWarning and Instruction Displays ....... 55

Weak Signal Display ........................... 33

Z ZERO SEARCH button .................... 8, 32

66

D4753S P36-60.p65 2003/03/13, 11:3266

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [e-mail]

DVD

A ACTION button ................................. 8, 49

ANGLE button

(Multiple Angle Viewing) ......... 8, 37, 47

AUDIO button

(Audio Soundtrack Language) ...... 8, 36

Audio Output

(For Selecting Audio Output) ............. 50

Auto-Power Off Function ..................... 23

B Bonus Group (For DVD-Audio) ........... 41

C CLEAR button ............................ 8, 39, 48

Component Video Output .............. 10, 13

D Delay Time Setup ................................ 52

Disc Languages ................................... 49

DISPLAY button

(“On-Screen Display”).................... 8, 42

DTS ...................................................... 14

DVD-Audio ........................................... 41

DVD Lock Ratings ............................... 48

DVD Menu ........................................... 38

DVD mode button ............................ 8, 28

F 5.1ch Analog Audio Output ........... 15, 51

Frame by Frame Picture ...................... 23

Forward/Reverse Chapter/Track Skip... 23

Forward/Reverse Scene Search .......... 23

J JPEG ............................................ 45 ~ 47

K Karaoke

(Vocal Selection for Karaoke Discs) ... 37

L Language Code List ............................ 54

MMENU button

(To display DVD Menu) ................. 8, 38

MP3 ...................................................... 45

Multiple Angle Viewing........................ 37

Multi-channel speaker system ...... 15, 51

O OPEN/CLOSE button ....................... 8, 22

Optical Digital Audio Output .......... 10, 15

Output Balance Setup ......................... 52

P PAGE button (Still Image Skip) ....... 8, 41

PLAY button (Play a Disc) ............... 8, 22

Program Play (For Video CD/ CD) ...... 39

PROGRESSIVE button .......................... 9

Progressive Scan................................. 10

R Random Play (For Video CD/ CD) ...... 40

Repeat Play ......................................... 44

Resume Function................................. 23

RETURN button ............................... 8, 22

Rotation................................................ 47

S SEARCH button

(Forward/Reverse Scene Search) .. 8, 23
SKIP l or l button
(Forward/Reverse Chapter/Track) 8, 23

Slide-show ........................................... 46

SLOW+/SLOW- button

(Slow Motion Picture) .................... 8, 23

Speaker Output Setup ......................... 51

Speaker Position ................................. 53

Speaker Size Setup ............................. 51

STILL button

(Still Picture or Pause) ................... 8, 23

Still Mode
(For selecting “FIELD” or “FRAME”)..53

STOP button ..................................... 8, 22

SUB TITLE button
(For selecting Subtitle Language) ... 8, 36

S-Video Out .................................... 10, 13

T Test Signal Setup ................................ 53

TITLE button (Title Menu) ................ 8, 38

TV Mode
(For selecting the screen display style) .. 53

2-channel speaker system .............. 15, 51

V Video CD ............................................. 23

VOLUME ADJUST button ................ 8, 40

V.S.S. (Virtual Surround Sound) ..... 8, 23

WWMA ..................................................... 45

Z ZOOM button (Picture Zoom) ..... 8, 37, 47

Information

For Your

D4753S P36-60.p65 2003/03/13, 11:3267

67

Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America

One Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.

Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina,
Puerto Rico 00985

D4753S P36-60 (030610 –§”Ô•Ï•X).p65 2003/06/10, 18:5568

P

Printed in Indonesia

LSQT0675A

S0303-1073