Panasonic PT-DZ8700E, PT-DW8300E User Manual

Operating Instructions

Functional Manual

DLP™ Based Projector

Model No.

PT-DZ8700U PT-DS8500U PT-DW8300U

Commercial Use

The projection lens is sold separately.

Thank you for purchasing a Panasonic Projector.

Before operating this product, please read the instructions carefully and save this manual for future use.

Before using your projector, be sure to read “

pages 8 to 16).

(

Precautions with regard to safety”

TQBJ0341

ENGLISH

Important Safety Notice

- ENGLISH

Important

Information

Important Safety Notice

Dear Panasonic Customer:

The following information should be read and understood as it provides details, which will enable you to operate the projector in a manner which is both safe to you and your environment, and conforms to legal requirements regarding the use of projectors. Before connecting, operating or adjusting this projector, please read these instructions completely and save this booklet with the projector for future reference. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic DLP™ Based projector. The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required.

Model number: PT-DZ8700U/PT-DS8500U/PT-DW8300U

Serial number:

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DONOT EXPOSE THIS PRODUCT

Power Supply: This Projector is designed to operate on 120 V, 60 Hz AC, house current only.

CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for

TO RAIN OR MOISTURE.

power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will

need to obtain a separate 250 V power cord. If you use the accessory cord in such situations, re

may result.

The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the

user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may

be of sufcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

CAUTION: This equipment is equipped with a three-pin grounding-type power

plug. Do not remove the grounding pin on the power plug. This plug

will only t a grounding-type power outlet. This is a safety feature. If

you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug.

Pursuant to at the directive 2004/108/EC, article 9 (2) Panasonic Testing Center Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg, F.R. Germany

NOTICE:

This product has a High Intensity Discharge (HID) lamp that contains mercury. Dispose may be regulated in • your community due to environmental considerations. For disposal or recycling information, please contact your local authorities, or the Electronic Industries Alliance: http://www.eiae.org

Do not remove

Important Safety Notice

ENGLISH -

Important

Information

WARNING:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. •

FCC CAUTION: To assure continued compliance, follow the attached installation instructions and use only

shielded interface cables when connecting to computer and/or peripheral devices. Any

changes or modications not expressly approved by Panasonic Corp. of North America could

void the user’s authority to operate this device.

WARNING:

Not for use in a computer room as dened in the Standard for the Protection of Electronic Computer/Data • Processing Equipment, ANSI/NFPA 75. For permanently connected equipment, a readily accessible disconnect device shall be incorporated in the • building installation wiring. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily • accessible.

Declaration of Conformity

Model Number: PT-DZ8700U/PT-DS8500U/PT-DW8300U Trade Name: Panasonic Responsible party: Panasonic Solutions Company Address: 3 Panasonic Way, Secaucus, NJ 07094 Telephone number: (877) 803 - 8492 E-mail: projectorsupport@us.panasonic.com This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information on Disposal in other Countries outside the European

These symbols are only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

Environment care information for users in China

This symbol is only valid in China.

- ENGLISH

Important

Information

Preparation Getting Started Basic Operation Settings Maintenance Appendix

The size is almost the same as the former model but the luminance is about 1.5 times higher.

Heightened luminance

7 000 lm : PT-D7700U

(two lamps LAMP POWER : [HIGH])

Quick steps

For details, see the corresponding pages.

1. Set up your projector. page 21)

(

10 600 lm : PT-DZ8700U

(two lamps LAMP POWER : [HIGH])

Lengthened lamp replacement cycle

The lamp replacement cycle is longer than the existing model. (

Approx. 1 500 hours : PT-D7700U

(two lamps LAMP POWER : [HIGH])

Approx. 3 000 hours : PT-DZ8700U

(two lamps LAMP POWER : [HIGH])

page 110)

Reduced standby power

The standby power is much less than the existing model.

2. Attach the projection lens. page 37)

(

3. Connect with other devices. page 34)

(

4. Connect the power cord. page 38)

(

5. Start projecting. page 39)

(

Approx. 12 W : PT-D7700U

Approx. 0.2 W : PT-DZ8700U

(STANDBY MODE : [ECO])

6. Select the input signal. page 41)

(

7. Adjust the image. page 41)

(

ENGLISH -

Important

Information

PreparationGetting StartedBasic OperationSettingsMaintenanceAppendix

Contents

Be sure to read “Precautions with regard to safety”. ( pages 8 to 16)

Important Information

Important Safety Notice ............................ 2

Precautions with regard to safety ............ 8

WARNING ..............................................................8

CAUTION .............................................................11

Cautions when transporting ................................. 11

Cautions when installing ......................................12

Security ................................................................14

Cautions on use ...................................................14

Cleaning and maintenance ..................................15

Disposal ...............................................................15

Accessories ..........................................................16

Preparation

About Your Projector .............................. 17

Remote control .....................................................17

Projector body ......................................................18

Setting projector ID number to remote control .....20

Using a wired remote control ...............................20

Making adjustment and selection.........................39

Powering off the projector ....................................40

Direct power off function ......................................40

Projecting ................................................. 41

Selecting the input signal .....................................41

How to adjust the focus, zoom and shift ..............41

Adjustment range after lens position

(optical shift) ..................................................42

Moving the projection lens position to the home

position ..........................................................43

Lens adjustment to compensate for uneven

screen focus ..................................................43

Basic operations using the remote

control................................................... 46

Using the SHUTTER function ..............................46

On-screen display function ..................................46

Switching the input signal ....................................46

STATUS function ..................................................46

Automatic adjustment ..........................................47

Using the FUNCTION button ...............................47

Displaying the internal test pattern.......................47

Changing the picture aspect ratio ........................48

Getting Started

Setting up ................................................. 21

Projection method ................................................21

Screen size and throw distance ...........................22

Front leg adjusters and throwing angle ................33

Connections ............................................. 34

Before connection to the projector .......................34

Connecting example : AV equipment ...................35

Connecting example : Computers........................36

Removing/attaching the projection lens

(optional)

How to install the projection lens .........................37

How to remove the projection lens.......................37

........................................................ 37

Basic Operation

Powering ON/OFF .................................... 38

Connecting the power cord ..................................38

Powering up the projector ....................................39

Settings

Menu Navigation ...................................... 49

Navigating through the menu ...............................49

MAIN MENU ........................................................50

SUB MENU ..........................................................50

PICTURE menu ........................................ 52

PICTURE MODE .................................................52

CONTRAST .........................................................53

BRIGHTNESS ......................................................53

COLOR ................................................................53

TINT .....................................................................53

COLOR TEMPERATURE ....................................54

GAMMA ................................................................55

SYSTEM DAYLIGHT VIEW .................................55

SHARPNESS .......................................................56

NOISE REDUCTION ...........................................56

DYNAMIC IRIS ....................................................56

SYSTEM SELECTOR ..........................................57

- ENGLISH

Important

Information

Preparation Getting Started Basic Operation Settings Maintenance Appendix

Contents

POSITION menu ....................................... 58

ADVANCED MENU ................................... 63

To display pictures complying with the sRGB

standard ........................................................57

SHIFT ...................................................................58

ASPECT ...............................................................58

ZOOM ..................................................................59

CLOCK PHASE ...................................................60

GEOMETRY (PT-DZ8700/PT-DS8500 only) .......60

KEYSTONE (PT-DW8300 only) ...........................62

DIGITAL CINEMA REALITY .................................63

BLANKING ...........................................................63

INPUT RESOLUTION ..........................................64

CLAMP POSITION ..............................................64

EDGE BLENDING ...............................................64

FRAME DELAY ....................................................66

RASTER POSITION ............................................66

LAMP SELECT ....................................................76

LAMP RELAY .......................................................76

LAMP POWER .....................................................77

BRIGHTNESS CONTROL ...................................77

STANDBY MODE ................................................81

SCHEDULE .........................................................81

RS-232C ..............................................................82

STATUS ...............................................................83

NO SIGNAL SHUT-OFF ......................................84

REMOTE2 MODE ................................................84

FUNCTION BUTTON ...........................................84

DATE AND TIME ..................................................84

LENS CALIBRATION ...........................................85

FILTER COUNTER RESET .................................85

SAVE ALL USER DATA ........................................86

LOAD ALL USER DATA .......................................86

INITIALIZE ...........................................................86

DISPLAY LANGUAGE menu ................... 67

Changing the display language............................67

DISPLAY OPTION menu .......................... 68

COLOR MATCHING ............................................68

LARGE SCREEN CORRECTION ........................69

SCREEN SETTING

(PT-DZ8700/PT-DS8500 only) ......................69

WAVEFORM MONITOR (PT-DZ8700 only) .........70

AUTO SIGNAL .....................................................71

AUTO SETUP ......................................................71

RGB IN (Only RGB input) ....................................72

DVI-D IN ...............................................................72

HDMI IN ...............................................................73

SDI IN (PT-DZ8700/PT-DS8500 only) .................73

ON-SCREEN DISPLAY .......................................73

BACK COLOR .....................................................74

STARTUP LOGO .................................................74

FREEZE ...............................................................74

PROJECTOR SETUP menu ..................... 75

PROJECTOR ID ..................................................75

INSTALLATION ....................................................75

HIGH ALTITUDE MODE ......................................75

COOLING CONDITION .......................................76

SERVICE PASSWORD .......................................86

P IN P menu .............................................. 87

Using the P IN P function .....................................87

Setting the P IN P function ...................................87

TEST PATTERN menu ............................. 88

TEST PATTERN ...................................................88

SIGNAL LIST menu .................................. 89

Registering a signal to the list ..............................89

Renaming a registered data.................................89

Deleting a registered data ....................................89

Managing the sub memory list .............................90

SECURITY menu ...................................... 91

SECURITY PASSWORD .....................................91

SECURITY PASSWORD CHANGE .....................91

DISPLAY SETTING .............................................92

TEXT CHANGE ...................................................92

MENU LOCK ........................................................92

MENU LOCK PASSWORD ..................................92

CONTROL DEVICE SETUP ................................93

NETWORK menu ..................................... 94

NETWORK SETUP ..............................................94

NETWORK CONTROL ........................................94

NETWORK STATUS ............................................94

ENGLISH -

Important

Information

PreparationGetting StartedBasic OperationSettingsMaintenanceAppendix

Network connections............................................95

Accessing from the Web browser ........................96

Contents

Maintenance

Monitor Lamp indicators ....................... 107

Managing the indicated problems ......................107

Replacement .......................................... 109

Before replacing the unit ....................................109

Replacing the unit ..............................................109

Troubleshooting .....................................112

Appendix

Technical Information ............................114

PJLink protocol ..................................................114

Control commands via LAN ............................... 115

Serial terminal ....................................................117

REMOTE 2 IN terminal ......................................120

Two window display combination list .................121

Restoring the MENU LOCK PASSWORD

to default......................................................121

List of compatible signals ...................................122

Specications ........................................ 124

Dimensions ........................................................126

About brand .......................................................126

Ceiling mount bracket safeguards....... 127

Attachment procedure........................................127

Index ....................................................... 128

- ENGLISH

Important

Information

Precautions with regard to safety

WARNING



The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible when problems occur. If the following problems occur, cut off the power supply immediately.

Continued use of the projector in these conditions will result in re or electric shock.

z z z

Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.

During a thunderstorm, do not touch the projector or the cable.

Electric shocks can result.

Do not do anything that might damage the power cord or the power plug.

If the power cord is used while damaged, electric shocks, short-circuits or re will result.

Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.

Insert the power plug securely into the wall outlet.

If the plug is not inserted correctly, electric shocks or overheating will result.

z z z

Clean the power plug regularly to prevent it from becoming covered in dust.

Failure to observe this will cause a re.

z z

Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.

Do not handle the power plug with wet hands.

Failure to observe this will result in electric shocks.

Do not overload the wall outlet.

If the power supply is overloaded (ex., by using too many adapters), overheating may occur and re will result.

POWER

If foreign objects or water get inside the projector, cut off the power supply. If the projector is dropped or the cabinet is broken, cut off the power supply. If you notice smoke, strange smells or noise coming from the projector, cut off the power supply.

Do not damage the power cord, make any modications to it, place it near any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.

Do not use anything other than the provided power cord. Do not use the provided power cord for other electrical equipment. Do not use plugs which are damaged or wall outlets which are coming loose from the wall.

If dust builds up on the power plug, the resulting humidity can damage the insulation. If not using the projector for an extended period of time, pull the power plug out from the wall outlet.



ON USE/INSTALLATION

Do not place liquid containers on top of the projector.

If water spills onto the projector or gets inside it, re or electric shocks will result.

If any water gets inside the projector, contact an Authorized Service Center.

Do not place the projector on soft materials such as carpets or sponge mats.

Doing so will cause the projector to overheat, which can cause burns, re or damage to the projector.

Do not set up the projector in humid or dusty places or in places where the projector may come into contact with oily smoke or steam, ex. a bathroom.

Using the projector under such conditions will result in re, electric shocks or components deterioration.

Components deterioration (such as ceiling mount brackets) may cause the projector which is mounted on the ceiling to fall down.

Do not install this projector in a place which is not strong enough to take the full weight of the projector or on top of a surface which is sloped or unstable.

Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage could result.

Precautions with regard to safety

ENGLISH -

Important

Information

Do not place another projector or other heavy objects on top of the projector.

Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or injury. The projector will be damaged or deformed.

Installation work (such as ceiling suspension) should only be carried out by a qualied

technician.

If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks.

Do not use anything other than an authorized ceiling mount bracket.

Be sure to use the provided accessory wire with an eye bolt as an extra safety measure to prevent the

projector from falling down. (Install in a different location to the ceiling mount bracket)

Do not cover the air inlet port or the air outlet port.

Doing so will cause the projector to overheat, which can cause re or damage to the projector.

Do not place the projector in narrow, badly ventilated places such as closets or bookshelves.

Do not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.

Do not place your hands or other objects close to the air outlet port.

Doing so will cause burns or damage your hands or other objects.

Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand

heat close to this port.

Do not look and place your skin into the lights emitted from the lens while the projector is being used.

Doing so can cause burns or loss of sight.

Strong light is emitted from the projector’s lens. Do not look or place your hands directly into this light.

Be especially careful not to let young children look into the lens. In addition, turn off the power and disconnect

the power plug when you are away from the projector.

Do not insert any foreign objects into the projector.

Doing so will cause re or electric shocks.

Do not insert any metal objects or ammable objects into the projector or drop them onto the projector.

Never attempt to remodel or disassemble the projector.

High voltages can cause re or electric shocks.

For any inspection, adjustment and repair work, please contact an Authorized Service Center.

Do not project an image with the lens cover attached.

Doing so can cause re.

When replacing the lamp, do not touch the fan with your nger or another part of your

body.

If you do so, you may get hurt.



ACCESSORIES

Do not use or handle the batteries improperly, and refer to the following.

Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re.

Do not use unspecied batteries.

Use manganese batteries but not rechargeable batteries.

Do not disassemble dry cell batteries.

Do not heat the batteries or place them into water or re.

Do not allow the + and

necklaces or hairpins. Do not store batteries together with metallic objects.

Store the batteries in a plastic bag and keep them away from metallic objects.

Make sure the polarities (+ and

Do not use a new battery together with an old battery or mix different types of batteries.

Do not use batteries with the outer cover peeling away or removed.

Remove the empty batteries from the remote control at once.

Insulate the battery using tape or something similar before disposal.

terminals of the batteries to come into contact with metallic objects such as

) are correct when inserting the batteries.

Precautions with regard to safety

- ENGLISH

Important

Information

Do not allow children to reach the AA/R6 batteries.

z z

If the battery uid leaks, do not touch it with bare hands, and take the following measures if

necessary.

Do not disassemble the lamp unit.

If the lamp breaks, it could cause injury.

Lamp replacement

The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will result.

z z z

Do not allow infants or pets to touch the remote control unit.

Keep the attached screws and plain washers away from babies and infants.

z z

The battery can cause personal injury if swallowed. If swallowed, seek medical advice immediately.

Battery uid on your skin or clothing could result in skin inammation or injury. Rinse with clean water and seek medical advice immediately. Battery uid coming in contact with your eyes could result in loss of sight. In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately.

Replacement of the lamp should be carried out by a qualied technician. The lamp can easily explode if struck against hard objects or dropped. Before replacing the lamp, be sure to disconnect the power plug from the wall outlet. Electric shocks or explosions can result if this is not done. When replacing the lamp, allow it to cool for at least one hour before handling it otherwise it can cause burns.

Keep the remote control unit out of the reach of infants and pets after using it.

If a baby swallows a screw by accident, it may be affected badly. If a baby seems to have swallowed a screw, consult the doctor immediately.

Precautions with regard to safety

ENGLISH -

Important

Information

CAUTION



POWER

When disconnecting the power cord, be sure to hold the power plug and power connector.

If the power cord itself is pulled, the lead will become damaged, and re, short-circuits or serious electric shocks

will result.

When not using the projector for an extended period of time, disconnect the power plug from the wall outlet and remove the batteries from the remote control.

Disconnect the power plug from the wall outlet before carrying out any cleaning.

Electric shocks can result if this is not done.



ON USE/INSTALLATION

Do not put your weight on this projector.

You could fall or the projector could break, and injury will result.

Be especially careful not to let young children stand or sit on the projector.

Do not place the projector in extremely hot locations.

Doing so will cause the outer casing or internal components to deteriorate, or result in re.

Take particular care in locations exposed to direct sunlight or near stoves.

Always disconnect all cables before moving the projector.

Moving the projector with cables still attached can damage the cables, which will cause re or electric shocks to

occur.

Do not place your hands in the openings beside the optical lens, while shifting the lens.

Failure to observe this could cause injury.



ACCESSORIES

Do not use the old lamp unit.

If used it could cause lamp explosion.

If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the broken pieces.

Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and which

contains nearly the same amount of mercury as uorescent lamps, and the broken pieces will cause injury.

If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical

advice immediately. Ask your dealer about replacing the lamp unit and check the inside of the projector.

Cautions when transporting

When transporting the projector or carrying it around, make sure that the lens cover is always in place, and remove the lens. Please take care to keep them away from vibration and impacts, both the projector and the lens are precision-made and easily susceptible to damage. When transporting the projector, the leg adjusters must be housed and do not hold them. Please securely hold only its bottom and none of its other parts or surfaces as this will result in malfunctions.

Precautions with regard to safety

- ENGLISH

Important

Information

Cautions when installing



After removing the projection lens, install the dust sponge attached to the projector.

If the dust sponge is not installed, dust will be accumulated inside and can cause a trouble.

Do not use under the following conditions.

Do not set up the projector outdoors.

The projector is designed for indoor use only.

Avoid setting up in places which are subject to vibration or shocks.

If the projector is installed in a place where vibrations are transmitted or mounted in a car or a vessel, vibrations or impacts will result in damage to the internal parts, causing failure. Install the product in a place free from vibrations and impacts.

Avoid setting up in places which are subject to sudden temperature changes, such as near an air conditioner or lighting equipment.

Failure to observe this will result in malfunctions or the lamp life will be shortened. See “ ■ TEMP indicator” on page 108.

Avoid setting up in places which are near high-voltage power lines or near motors.

The product will be exposed to interference if it is installed in the vicinity of high-voltage electrical power lines or power sources.

Do not install the projector at elevations higher than 2 700 m (8 858 ft) above sea level. If using this projector at high elevations 1 400 - 2 700 m (4 593 - 8 858 ft) above sea level, set [HIGH ALTITUDE MODE] to [ON]. If using this projector at elevations lower than 1 400 m (4 593 ft) above sea level, set [HIGH ALTITUDE MODE] to [OFF].

Failure to observe this will result in malfunctions or the lamp life or life of other components will be shortened.

When installing and using the projector at an angle that exceeds 30° vertically, set [COOLING CONDITION].

Failure to observe this will result in malfunctions or the lamp life or other components will be shortened.



Lens Focus

Do not adjust the lens focus in the initial period after switching the projector on. The high clarity projector lens is thermally affected by the light from the light source, making the focus unstable in the period just after switching on. Please allow a warm-up time of at least 30 minutes before adjusting the lens focus.



Be sure to ask a specialized technician when installing the product to a ceiling.

If the product is to be installed hanging from the ceiling, purchase an optional Ceiling Mount Attachment (For high ceilings: Model No. ET-PKD310H, For low ceilings: Model No. ET-PKD310S). Please call a specialized technician or contact an Authorized Service Center for installation.

Precautions with regard to safety

ENGLISH -

Important

Information



Cautions when setting the projectors 1

When installing and using the projector with a method other than oor standing installing using adjustable

feet, x it with the 5 ceiling mounting screws (shown in the gure). (Screw diameter: M6, Tapping depth inside set: 8 mm) Make a clearance of at least 5 mm between the projector bottom and setting surface by inserting spacers

(metallic) etc. between them. The adjustable feet can be removed if they are not necessary for installation. However, do not use the screw

holes for them to x the projector. Do not tighten other screws etc. into the screw holes for the adjustable feet. Doing so can break the set. When installing the removed adjustable feet again, note that the front and rear ones have different lengths. (The longer screws are used for front feet. Length of front leg screw: 65 mm, Length of rear leg screw: 23 mm) When installing the projector with a method other than oor standing installing, do not adjust its angle with the

adjustable feet. Doing so can break the set.

Ceiling mounting screws (M6)

Base

Spacers

Gap (Min. 5 mm)

Make sure air can circulate around the air intake vent. Failure to do so may result

in the projector not operating

properly.

Precautions with regard to safety

- ENGLISH

Important

Information



Cautions when setting the projectors 2

When placing the projector in conned space, a ventilation or air conditioning system must be equipped, and keep enough ventilation space on the rear and both sides of the projector.

over 50 cm (20")

over 10 cm (4")

Make a clearance of at least 5 mm between the projector bottom and setting surface by inserting spacers

(metallic) etc. between them.

zDo not stack the projectors without using frame or shelf.

Do not cover the ventilation openings or place anything within 50 cm (20") of them

as this may cause damage or injury. Avoid heating or cooling air of the air conditioning systems directly blow on to the

projector ventilation openings. You can tilt the projector within ± 15 degrees horizontally.

+15°

over 50 cm (20") over 50 cm (20")

15°

Security



Take safety measures against following incidents.

Personal information being leaked via this product.

Unauthorized operation of this product by a malicious third party.

Interfering or stopping of this product by a malicious third party.



Security instruction

The connecting network must be secured by rewall or others.

Change your password regularly.

Do not use a password that is simple to guess.

Panasonic and its afliate companies would never directly inquire about your password.

Do not share your password with the general public.

Set a password, and place restrictions on the users who can log in.

Cautions on use



In order to get the picture quality

Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light

from indoor lamps from shining onto the screen. Depending on where the projector is used, air exhaust vents or the warm air from air conditioning can cause

a shimmering effect on the screen. For this reason, take care not to shield the air exhaust vents and consider

the direction of the air owing from air conditioning.

Precautions with regard to safety

ENGLISH -

Important

Information

Do not touch the surface of the projector lens with your bare hand.

If the surface of the lens becomes dirty from ngerprints or anything else, this will be magnied and projected

onto the screen. Please put the lens cover on the projector when you do not use it.



Do not move the projector while it is operating or subject it to vibration or impact.

The service life of its internal components will be shortened.



The projector has a high pressure mercury lamp that is characterized as follows:

The brightness of the lamp will decrease over time.

The lamp may explode or shorten the lamp life by shocks or chipping damage.

In rare cases, it may burst shortly after the rst use.

The possibility of its bursting increases when the lamp is used beyond the replacement time.

If the lamp bursts, gas inside the lamp is released in the form of smoke.

The life of a mercury lamp varies according to the individual difference or conditions of use.

In particular, turning the power on and off frequently and/or repeatedly as well as continuous use for 22 hours

will greatly affect the life cycle. Provide a lamp for replacement in advance. Lamp deterioration accelerates when used continuously for 22 hours or more. Lamp deterioration due to

continuous use can be reduced by using the “LAMP RELAY” function.



Connection to external device

When connecting the projector to a computer or external device, use the power cord supplied with the corresponding device and a commercially available shielded interface cable.



Optical components

It may be necessary to replace the optical components such as DLP chips and Polarizing plates in less than 1 year if using the projector in a high temperature environment or in a very dusty, oily smoke or tobacco smoke environment. For more details, please contact your dealer.



DLP chips

The DLP chips are precision-made. Note that in rare cases, pixels of high precision could be missing or always lit, but this is not a malfunction. Please take note that directing a laser beam onto the lens surface can damage the DMD element.

Cleaning and maintenance



Ask an Authorized Service Center to clean the inside of the projector at least once a year.

If dust is left to build up inside the projector without being cleaned out, it can result in re or problems with

operation. It is a good idea to clean the inside of the projector before the season when humid weather arrives. Ask your nearest Authorized Service Center to clean the projector when required. Please discuss with the Authorized Service Center regarding cleaning costs.

Be sure to remove the power plug from the wall outlet before cleaning.

Use soft and dry cloth to clean the cabinet.

Use a soft cloth moistened in warm water to clean away oil. Do not use solvents such as benzene, thinner, and alcohol, detergents for kitchens, or a chemical cloth. If using such solvents, the outer case will become deformed, and the paint may peel off.

Do not clean the lens surface with fuzzy or dusty cloths.

If dust adheres to the lens, it will be magnied and projected on the screen. Use a soft and clean cloth to wipe

off dust.

Disposal

When discarding this product, please contact your local authorities or dealer and ask for the correct method of disposal.

Precautions with regard to safety

Information

Important

Accessories

Make sure the following accessories are provided with your projector.

Remote control (x1) (N2QAYB000550)

Power cord (x1) (TXFSX01RGQZ)

CD-ROM (x1) (TXFQB02VKN)

Drop-prevention bracket (x2) (TTRA0238)

AA/R6 batteries for remote control (x2)

Safety cables (x2) Washers (x4)

Wire rope xing screw (x2)

Lens xing screw (x1)

(XYN4+J18FJ)

Attention

After unpacking the projector, discard the power cord cap and packaging material properly.

For lost accessories, consult your dealer.

The part numbers of accessories and separately sold components are subject to change without notice.

Store small parts in an appropriate manner, and keep them away from young children.

- ENGLISH

About Your Projector

Remote control

Top view

Remote control signal emitters

Front view

Remote control indicator

Flashes by pressing any buttons.

Starts the projection while in the standby mode.

These buttons select the RGB1, RGB2, DVI-D, VIDEO, S-VIDEO and SDI terminals. (

<MENU> button

Displays and clears the main menu, and returns to the previous menu when the menu is displayed.

Navigation and <ENTER> buttons

Navigate through the menu items with

▲▼◄►, and activate them with the

<ENTER> button. ( Displays and clears the on

screen indications.

(

page 46)

Displays the test pattern.

(

page 47)

Enter ID number of the remote control and adjustment values of menu items.

Displays projector information.

Makes the remote control available to control any ID projectors.

(

page 20)

page 46)

page 49)

Bottom view

Remote control wired terminal

(

page 20)

Installing/removing batteries

Press the tab and lift up the cover.

Returns to the standby mode.

Pressing this button while projecting an image automatically corrects the picture positioning on the screen. While the auto setup feature is active, a message “PROGRESS” appears on the screen. (

Pressing this button toggles the projector’s internal mechanical shutter to black out the projector.

(

Switches the image aspect ratio.

(

These buttons are used together with

▲▼◄► to adjust focus, zoom and

shift by the projection lens. (

Assign the frequently use functions from options for shortcut.

(

Restores the default factory setting.

(

Species the ID of the remote control.

(

Insert the batteries according to the polarity diagram indicated inside. (insert the

Remove the batteries in the reverse order to setting.

page 47)

page 46)

page 48)

pages 39, 41)

page 47)

page 49)

page 20)

side rst).

Preparation

Attention

Do not drop the remote control.

Avoid contact with liquids or moisture.

Do not attempt to modify or disassemble the remote control.

Do not let strong light shine onto the signal receptor. The remote control may malfunction under strong light such as

uorescent.

Note

The remote control can be used within a distance of about 30

remote control can control at angles of up to ± 15 be reduced. If there are any obstacles between the remote control and the remote control signal receptor, the remote control may not

operate correctly.

The signal will be reected off the screen. The operating range may differ due to the screen material. When the projector receives a signal from the remote control, the Power indicator will ash.

°C vertically and ± 30 °C horizontally, but the effective control range may

m if pointed directly at the remote control receiver. The

ENGLISH -

About Your Projector

Projector body

Preparation

Front view

Power indicator (STANDBY(R) / ON(G)) Indicates the power supply status.

Lamp1 indicator (LAMP1) Indicates the lamp1 unit status. (

Lamp2 indicator (LAMP2) Indicates the lamp2 unit status. (

Temperature indicator (TEMP) Indicates the temperature status. (

Filter indicator (FILTER) Indicates the lter status. (

Remote control signal receptor

Front leg adjusters

Screw up/down to adjust the projection angle.

page 107)

page 108)

Side views

Security lock

CONTROL

PANEL

AC IN terminal

Connect the power cord to supply electronic power to the projector.

<MAIN POWER> switch

Switch the projector on/off.

Air intake port

Auto Cleaning Filter (ACF) compartment (

page 109)

Air intake portTerminals on side

Air intake port

Rear view

Air exhaust port

Lamp unit compartment (

page 110)

Remote control signal receptor

Air exhaust port

Attention

Keep your hands and other objects away from the air outlet port.

Keep your hand and face away.

Keep heat-sensitive articles away.

Inserting your nger may result in injury.

Heated air from the air outlet port can cause burns or deformations.

Bottom view

Burglar hook port

: Attach a commercial burglar prevention cable.

Air intake port

- ENGLISH

About Your Projector

ENGLISH -

Preparation

CONTROL PANEL

<STANDBY> button

Returns to the standby mode.

<POWER ON> button

Starts the projection while in the standby mode.

VIDEO

Switches to VIDEO input.

S-VIDEO

Switches to S-VIDEO input.

RGB1

Switches to RGB1 input.

RGB2

Switches to RGB2 input.

DVI-D/HDMI

Switches to DVI-D or HDMI input.

SDI

Switches to SDI input. (PT-DZ8700U/PT-DS8500U only)

Terminals on side

<MENU> button

Displays and clears the main menu, and returns to the previous menu when the menu is displayed. If you hold it down for at least 3 seconds while the on-screen indication is [OFF], the [OFF] state is canceled. (

<LENS> button

This button is used together with ▲▼◄► to

adjust focus, zoom and shift by the projection lens.

<ENTER> button

Press to activate a menu selection or to initiate a function.

<SHUTTER> button

Pressing this button toggles the projector’s internal mechanical shutter to black out the projector. (

▲▼◄► button

Use these buttons to select menu items, change settings, adjust levels, and to enter the [SECURITY] password.

<AUTO SETUP> button

Pressing this button while projecting an image automatically corrects the picture positioning on the screen. While the auto setup feature is active, a message “PROGRESS” appears on the screen.

(

page 47)

page 46)

page 49)

REMOTE 2 IN

Connect a cable from an external control circuit.

REMOTE 1 IN/OUT

When two or more main units are used in the system, they can be connected and controlled with wired remote control cable.

SDI IN

Connect an SDI signals. (PT-DZ8700U/PT-DS8500U only)

HDMI IN

Connect a HDMI signals.

VIDEO IN

Connect a VIDEO signals.

S-VIDEO IN

Connect an S-VIDEO signals.

Attention

Do not touch the LAN terminal with your bare hands or body, as body parts may have charged static electricity. Failure to

do so may cause malfunctions. Do not touch the metallic parts of LAN terminal and cable. Please connect the LAN to indoor devices only.

SERIAL IN/OUT

Connect an RS-232C cable from/to a computer.

DVI-D IN

Connect a single link DVI-D signals.

LAN

Connect a LAN cable for network connection.

RGB2 IN

Connect an RGB or YP

RGB (YPBPR)1 IN

Connect an RGB or YP

BPR

signals.

About Your Projector

Setting projector ID number to remote control

Each projector can be assigned a unique ID number, and the handheld remote’ s number must be set to match the intended projector. The ID number of the projector is set to “ALL” on shipping, and use the ID ALL button of the remote

Preparation

control when using only a single projector.

Attention

Do not press <ID SET> button accidentally or carelessly

because the ID number on the remote control can be set even when no projector is around. If you do not enter the 2 digits ID number within 5

seconds after <ID SET> button has been pressed, the ID will remain at the number that was set before <ID SET> button was pressed. Your specied ID number is stored in the remote control

unit unless another one is specied later. However, the

stored ID will be erased if the batteries of the remote control are left exhausted. When the batteries are replaced, set the same ID number again. The ID number can be set to “ALL” or from “1” to “64”.

Press <ID SET> button, and the 1 ) projector (s) will display it’s current ID number onscreen. Within 5 seconds, use the numeric keys (0-9) to match the Remote’s ID number with that of the desired projector.

Using a wired remote control

When multiple projectors are connected as part of the system, connect to units with a M3 stereo mini jack commercial cable to simultaneously control multiple main units with a single remote control through the REMOTE 1 IN/OUT terminal. It is effective to use the wired remote control in the environment in which an obstacle stands in the light path or where devices are susceptible to outside light.

Connect to the remote control wired terminal

Remote Control

M3 stereo mini jack cable (commercial)

Connect to the secondary projector

Connection terminals

Note

Refer to “PROJECTOR ID” of “PROJECTOR SETUP

menu” (

page 75).

Attention

Use 2 core shielded cable of length of 15 m or less. If the

length of the cable exceeds 15 m (49' 2"), the shielding

of the cable may not be sufcient and the remote control

may not work.

- ENGLISH

Setting up

Projection method

You can use the projector with any of the following 4 projection methods. To set the desired method in the projector.

Mounting on the ceiling and projecting from front

INSTALLATION FRONT/CEILING

COOLING

CONDITION

Mounting on the ceiling and

Method

CEILING SETTING

projecting from rear

(Using translucent screen)

Setting on a desk/oor and projecting from rear

(Using translucent screen)

INSTALLATION REAR/FLOOR

COOLING

CONDITION

Setting on a desk/oor and

Method

FLOOR SETTING

projecting from front

Getting Started

INSTALLATION REAR/CEILING

COOLING

CONDITION

Refer to “INSTALLATION” of “PROJECTOR SETUP menu: details.

CEILING SETTING

Method

INSTALLATION FRONT/FLOOR

COOLING

CONDITION

” and “COOLING CONDITION” (

Method

FLOOR SETTING

pages 75, 76) for

ENGLISH -

Setting up

- ENGLISH

Getting Started

Screen size and throw distance

When planning the projector and screen geometry, refer to the gures below and the information on the following

pages for reference. After the projector is roughly positioned, picture size and vertical picture positioning can be

nely adjusted with the powered zoom lens and lens shifting mechanism.

Projected image

L (LW/LT)

SH Height of the projection area (m)

SW Width of the projection area (m)

SD Diagonal length of the projection area (")

LW : Minimum distance: LT : Maximum distance

Screen

Projection distance (m)

L (LW/LT)

Screen

Vertical distance between the lens center level and the bottom edge of the projected image. (m)

Attention

Before installing, please read

Special care should be used when DLP projectors are used in the same room as high power laser equipment.

Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices ™ in which case there is a loss of warranty.

“Precautions with regard to safety” (Æ pages 8 to 16)

Setting up

ENGLISH -

Getting Started

Projected range using geometric adjustment (PT-DZ8700U/PT-DS8500U only)

VERTICAL KEYSTONE (Side View) HORIZONTAL KEYSTONE (Top View)

Screen Screen

VERTICAL ARC (Side View) HORIZONTAL ARC (Top View)

L2 : Projection distance R2 : Radius of the circle

Screen

Center of the circle

Screen

L3 : Projection distance

Keystone correction only When using arc and keystone correction together Arc correction only

Lens

ET-D75LE1 ±40 ±15 ±5 ±5 1.6 3.2 0.8 1.6 ET-D75LE2 ±40 ±15 ±5 ±5 1.2 2.4 0.6 1.2 ET-D75LE3 ±40 ±15 ±10 ±10 0.8 1.6 0.4 0.8 ET-D75LE4 ±40 ±15 ±10 ±15 0.6 1.0 0.3 0.5 ET-D75LE5 ±22 ±15 ±5 ±5 3.0 6.0 1.5 3.0 ET-D75LE6 ±28 ±10 ±5 ±5 2.4 4.8 1.2 2.4 ET-D75LE8 ±40 ±15 ±10 ±15 0.4 0.8 0.2 0.4 ET-D75LE10 ±40 ±15 ±5 ±5 1.6 3.2 0.8 1.6 ET-D75LE20 ±40 ±15 ±5 ±5 1.6 3.2 0.8 1.6 ET-D75LE30 ±40 ±15 ±5 ±5 1.2 2.4 0.6 1.2

Vertical

Keystone

Correction

Angle α (°)

R3 : Radius of the circle

Horizontal

Keystone

Correction

Angle β (°)

Vertical

Keystone

Correction

Angle α (°)

Horizontal

Keystone

Correction

Angle β (°)

Screen

Center of the circle

R2/L2

minimum

value

Screen

R3/L3

minimum

value

L2 : Projection distance R2 : Radius of the circle

L3 : Projection distance R3 : Radius of the circle

R2/L2

minimum

value

R3/L3

minimum

value

Note

z z

When using geometric adjustment, if the amount of compensation is too great, excessive blurring may result. The curved screens illustrated are simply sections of a full circle.

Setting up

- ENGLISH

Getting Started

Projection distance by projection lens (for PT-DZ8700U)

For the screen aspect ratio of 16 : 10 (Unit : m)

Model number of

Screen dimensions Projection distance (L)

Screen size (")

70 0.942 1.508 2.01 2.69 2.72 4.10 4.11 6.90 6.91 11.06 10.78 20.56 80 1.077 1.723 2.31 3.09 3.12 4.70 4.71 7.90 7.91 12.66 12.37 23.55

90 1.212 1.939 2.61 3.49 3.52 5.30 5.31 8.91 8.91 14.25 13.97 26.54 100 1.346 2.154 2.91 3.89 3.92 5.90 5.91 9.91 9.91 15.85 15.57 29.53 120 1.615 2.585 3.51 4.68 4.73 7.10 7.11 11.91 11.92 19.04 18.76 35.50 150 2.019 3.231 4.40 5.88 5.93 8.90 8.91 14.92 14.93 23.82 23.54 44.47 200 2.692 4.308 5.89 7.87 7.93 11.91 11.92 19.94 19.95 31.80 31.52 59.41 250 3.365 5.385 7.39 9.87 9.93 14.91 14.92 24.95 24.96 39.77 39.49 74.36 300 4.039 6.462 8.88 11.86 11.93 17.91 17.92 29.97 29.98 47.75 47.47 89.30 350 4.712 7.539 10.37 13.86 13.93 20.91 20.92 34.98 34.99 55.72 55.44 104.24 400 5.385 8.616 11.86 15.85 15.94 23.92 23.93 40.00 40.01 63.70 63.42 119.19 500 6.731 10.770 14.85 19.84 19.94 29.92 29.93 50.03 50.04 79.65 79.37 149.08 600 8.077 12.923 17.83 23.82 23.94 35.93 35.94 60.06 60.07 95.60 95.32 178.96

Lens type Zoom lens

projection lens

Throw ratio

Effective

height

(SH)

Effective

width (SW)

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8

1.4–1.8 : 1 1.8–2.8 : 1 2.8–4.6 : 1 4.6–7.4 : 1 7.3–13.8 : 1

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Lens type Zoom lens Fixed-focus lens

Model number of

projection lens

(SH)

Effective

width (SW)

Throw ratio

Screen dimensions Projection distance (L)

Screen size (")

100 1.346 2.154 1.96 2.34 2.76 3.56 3.55 5.17 5.13 9.99 1.45 120 1.615 2.585 2.36 2.82 3.32 4.30 4.28 6.22 6.18 12.03 1.76 150 2.019 3.231 2.96 3.55 4.18 5.40 5.37 7.81 7.75 15.08 2.22 200 2.692 4.308 3.97 4.75 5.60 7.24 7.19 10.45 10.38 20.16 2.99 250 3.365 5.385 4.98 5.96 7.02 9.07 9.00 13.09 13.00 25.25 3.76 300 4.039 6.462 5.99 7.17 8.44 10.91 10.82 15.73 15.62 30.34 4.53 350 4.712 7.539 6.99 8.37 9.86 12.74 12.64 18.37 18.24 35.42 400 5.385 8.616 8.00 9.58 11.28 14.58 14.46 21.01 20.86 40.51 500 6.731 10.770 10.01 11.99 14.12 18.25 18.09 26.29 26.11 50.68 600 8.077 12.923 12.03 14.40 16.96 21.92 21.73 31.58 31.35 60.85

Effective

height

70 0.942 1.508 1.35 1.62 1.90 2.46 2.46 3.58 3.56 6.94 0.99

80 1.077 1.723 1.55 1.86 2.19 2.83 2.82 4.11 4.08 7.96 1.15

90 1.212 1.939 1.76 2.10 2.47 3.20 3.19 4.64 4.61 8.98 1.30

ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5

0.9–1.1 : 1 1.3–1.7 : 1 1.7–2.4 : 1 2.4–4.7 : 1 0.7 : 1

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Fixed

The throw ratio is based on the value during projection onto a 150-inch screen size.:

Note

The projection distances listed here involve an error of ±5 %.

When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied

size.

Setting up

ENGLISH -

Getting Started

For the screen aspect ratio of 16 : 9 (Unit : m)

Lens type Zoom lens

Model number of

projection lens

(SH)

Effective

width (SW)

Throw ratio

Screen dimensions Projection distance (L)

Screen size (")

100 1.245 2.214 2.99 4.00 4.04 6.07 6.08 10.19 10.19 16.29 16.01 30.36 120 1.494 2.657 3.60 4.82 4.86 7.30 7.31 12.25 12.26 19.57 19.29 36.50 150 1.868 3.321 4.53 6.05 6.09 9.15 9.16 15.34 15.35 24.49 24.21 45.72 200 2.491 4.428 6.06 8.10 8.15 12.24 12.25 20.50 20.50 32.69 32.40 61.08 250 3.113 5.535 7.59 10.15 10.21 15.33 15.34 25.65 25.66 40.88 40.60 76.44 300 3.736 6.641 9.13 12.19 12.27 18.41 18.42 30.81 30.81 49.08 48.80 91.79 350 4.358 7.748 10.66 14.24 14.32 21.50 21.51 35.96 35.97 57.28 57.00 107.15 400 4.981 8.855 12.19 16.29 16.38 24.58 24.60 41.12 41.12 65.47 65.19 122.51 500 6.226 11.069 15.26 20.39 20.50 30.76 30.77 51.42 51.43 81.87 81.59 153.23 600 7.472 13.283 18.33 24.49 24.61 36.93 36.94 61.73 61.74 98.26 97.98 183.95

Effective

height

70 0.872 1.550 2.07 2.77 2.80 4.21 4.23 7.09 7.10 11.37 11.09 21.14 80 0.996 1.771 2.38 3.18 3.21 4.83 4.84 8.13 8.13 13.01 12.73 24.21 90 1.121 1.992 2.68 3.59 3.62 5.45 5.46 9.16 9.16 14.65 14.37 27.29

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8

1.4–1.8 : 1 1.8–2.8 : 1 2.8–4.6 : 1 4.6–7.4 : 1 7.3–13.8 : 1

Min. (LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Lens type Zoom lens Fixed-focus lens

Model number of

projection lens

(SH)

Effective

width (SW)

Throw ratio

Screen dimensions Projection distance (L)

Screen size (")

100 1.245 2.214 2.01 2.41 2.83 3.67 3.65 5.31 5.28 10.28 1.50 120 1.494 2.657 2.43 2.90 3.42 4.42 4.40 6.40 6.35 12.37 1.81 150 1.868 3.321 3.05 3.65 4.29 5.55 5.52 8.03 7.97 15.50 2.29 200 2.491 4.428 4.08 4.89 5.75 7.44 7.39 10.74 10.67 20.73 3.08 250 3.113 5.535 5.12 6.13 7.21 9.33 9.26 13.46 13.36 25.96 3.87 300 3.736 6.641 6.15 7.37 8.67 11.21 11.13 16.17 16.06 31.18 4.66 350 4.358 7.748 7.19 8.61 10.13 13.10 12.99 18.88 18.75 36.41 400 4.981 8.855 8.22 9.85 11.59 14.99 14.86 21.60 21.45 41.64 500 6.226 11.069 10.29 12.33 14.51 18.76 18.60 27.03 26.84 52.09 600 7.472 13.283 12.36 14.81 17.44 22.54 22.33 32.46 32.23 62.54

Effective

height

70 0.872 1.550 1.39 1.66 1.96 2.53 2.53 3.68 3.66 7.14 1.02 80 0.996 1.771 1.60 1.91 2.25 2.91 2.91 4.23 4.20 8.19 1.18 90 1.121 1.992 1.81 2.16 2.54 3.29 3.28 4.77 4.74 9.23 1.34

ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5

0.9–1.1 : 1 1.3–1.7 : 1 1.7–2.4 : 1 2.4–4.7 : 1 0.7 : 1

Min. (LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Fixed

z z

The throw ratio is based on the value during projection onto a 150-inch screen size.:

Note

The projection distances listed here involve an error of ±5 %. When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied size.

Setting up

- ENGLISH

Getting Started

For the screen aspect ratio of 4 : 3 (Unit : m)

Model number of

Screen dimensions Projection distance (L)

Screen size (")

70 1.067 1.422 2.29 3.06 3.09 4.65 4.66 7.83 7.83 12.54 12.25 23.32

80 1.219 1.626 2.63 3.51 3.55 5.33 5.34 8.96 8.97 14.34 14.06 26.71

90 1.372 1.829 2.96 3.96 4.00 6.01 6.02 10.10 10.10 16.15 15.87 30.09 100 1.524 2.032 3.30 4.41 4.45 6.69 6.70 11.23 11.24 17.96 17.67 33.47 120 1.829 2.438 3.98 5.32 5.36 8.05 8.06 13.50 13.51 21.57 21.28 40.24 150 2.286 3.048 4.99 6.67 6.72 10.09 10.10 16.91 16.92 26.98 26.70 50.39 200 3.048 4.064 6.68 8.93 8.99 13.49 13.50 22.59 22.59 36.01 35.73 67.31 250 3.810 5.080 8.37 11.18 11.25 16.89 16.90 28.27 28.27 45.04 44.76 84.23 300 4.572 6.096 10.06 13.44 13.52 20.29 20.30 33.94 33.95 54.07 53.79 101.14 350 5.334 7.112 11.75 15.70 15.79 23.69 23.70 39.62 39.63 63.10 62.82 118.06 400 6.096 8.128 13.44 17.96 18.05 27.09 27.10 45.30 45.31 72.13 71.85 134.98 500 7.620 10.160 16.82 22.47 22.58 33.89 33.90 56.65 56.66 90.18 89.91 168.81 600 9.144 12.192 20.20 26.98 27.12 40.69 40.70 68.01 68.02 108.24 107.96 202.65

Lens type Zoom lens

projection lens

Throw ratio

Effective

height

(SH)

Effective

width (SW)

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8

1.6–2.2 : 1 2.2–3.3 : 1 3.3–5.6 : 1 5.6–8.9 : 1 8.8–16.5 : 1

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Lens type Zoom lens Fixed-focus lens

Model number of

projection lens

(SH)

Effective

width (SW)

Throw ratio

Screen dimensions Projection distance (L)

Screen size (")

100 1.524 2.032 2.22 2.66 3.13 4.05 4.03 5.86 5.82 11.34 1.66 120 1.829 2.438 2.68 3.20 3.77 4.88 4.86 7.06 7.01 13.64 2.00 150 2.286 3.048 3.36 4.02 4.74 6.13 6.09 8.85 8.79 17.09 2.53 200 3.048 4.064 4.50 5.39 6.35 8.21 8.15 11.84 11.76 22.85 3.40 250 3.810 5.080 5.64 6.76 7.96 10.28 10.20 14.83 14.73 28.61 4.27 300 4.572 6.096 6.78 8.12 9.56 12.36 12.26 17.82 17.70 34.36 5.14 350 5.334 7.112 7.92 9.49 11.17 14.44 14.32 20.81 20.67 40.12 400 6.096 8.128 9.06 10.85 12.78 16.52 16.38 23.80 23.63 45.88 500 7.620 10.160 11.34 13.58 16.00 20.68 20.49 29.78 29.57 57.39 600 9.144 12.192 13.62 16.32 19.21 24.83 24.61 35.76 35.51 68.91

Effective

height

70 1.067 1.422 1.54 1.84 2.17 2.80 2.80 4.07 4.04 7.88 1.13

80 1.219 1.626 1.77 2.11 2.49 3.22 3.21 4.67 4.64 9.03 1.31

90 1.372 1.829 2.00 2.38 2.81 3.63 3.62 5.27 5.23 10.19 1.48

ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5

1.1–1.3 : 1 1.6–2.0 : 1 2.0–2.9 : 1 2.9–5.6 : 1 0.8 : 1

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Fixed

The throw ratio is based on the value during projection onto a 150-inch screen size.:

Note

The projection distances listed here involve an error of ±5 %.

When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied

size.

Setting up

ENGLISH -

Getting Started

Projection distance by projection lens (for PT-DS8500U)

For the screen aspect ratio of 4 : 3 (Unit : m)

Lens type Zoom lens

Model number of

projection lens

(SH)

Effective

width (SW)

Throw ratio

Screen dimensions Projection distance (L)

Screen size (")

100 1.524 2.032 2.99 4.00 4.04 6.07 6.08 10.19 10.19 16.29 16.01 30.36 120 1.829 2.438 3.60 4.82 4.86 7.30 7.31 12.25 12.26 19.57 19.29 36.50 150 2.286 3.048 4.53 6.05 6.09 9.15 9.16 15.34 15.35 24.49 24.21 45.72 200 3.048 4.064 6.06 8.10 8.15 12.24 12.25 20.50 20.50 32.69 32.40 61.08 250 3.810 5.080 7.59 10.15 10.21 15.33 15.34 25.65 25.66 40.88 40.60 76.44 300 4.572 6.096 9.13 12.19 12.27 18.41 18.42 30.81 30.81 49.08 48.80 91.79 350 5.334 7.112 10.66 14.24 14.32 21.50 21.51 35.96 35.97 57.28 57.00 107.15 400 6.096 8.128 12.19 16.29 16.38 24.58 24.60 41.12 41.12 65.47 65.19 122.51 500 7.620 10.160 15.26 20.39 20.50 30.76 30.77 51.42 51.43 81.87 81.59 153.23 600 9.144 12.192 18.33 24.49 24.61 36.93 36.94 61.73 61.74 98.26 97.98 183.95

Effective

height

70 1.067 1.422 2.07 2.77 2.80 4.21 4.23 7.09 7.10 11.37 11.09 21.14 80 1.219 1.626 2.38 3.18 3.21 4.83 4.84 8.13 8.13 13.01 12.73 24.21 90 1.372 1.829 2.68 3.59 3.62 5.45 5.46 9.16 9.16 14.65 14.37 27.29

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8

1.5–2.0 : 1 2.0–3.0 : 1 3.0–5.0 : 1 5.0–8.0 : 1 7.9–15.0 : 1

Min. (LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Lens type Zoom lens Fixed-focus lens

Model number of

projection lens

(SH)

Effective

width (SW)

Throw ratio

Screen dimensions Projection distance (L)

Screen size (")

100 1.524 2.032 2.01 2.41 2.82 3.64 3.63 5.28 5.24 10.21 1.50 120 1.829 2.438 2.43 2.90 3.40 4.39 4.37 6.36 6.31 12.29 1.81 150 2.286 3.048 3.05 3.65 4.27 5.52 5.49 7.98 7.92 15.41 2.29 200 3.048 4.064 4.08 4.89 5.72 7.39 7.34 10.67 10.60 20.60 3.08 250 3.810 5.080 5.12 6.13 7.17 9.27 9.20 13.37 13.28 25.79 3.87 300 4.572 6.096 6.15 7.37 8.62 11.14 11.06 16.07 15.96 30.99 4.66 350 5.334 7.112 7.19 8.61 10.07 13.02 12.91 18.77 18.63 36.18 400 6.096 8.128 8.22 9.85 11.52 14.90 14.77 21.46 21.31 41.38 500 7.620 10.160 10.29 12.33 14.42 18.65 18.48 26.86 26.67 51.77 600 9.144 12.192 12.36 14.81 17.33 22.40 22.19 32.25 32.03 62.15

Effective

height

70 1.067 1.422 1.39 1.66 1.95 2.52 2.52 3.66 3.64 7.10 1.02 80 1.219 1.626 1.60 1.91 2.24 2.89 2.89 4.20 4.17 8.13 1.18 90 1.372 1.829 1.81 2.16 2.53 3.27 3.26 4.74 4.71 9.17 1.34

ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5

1.0–1.2 : 1 1.4–1.8 : 1 1.8–2.6 : 1 2.6–5.1 : 1 0.8 : 1

Min. (LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Fixed

z z

The throw ratio is based on the value during projection onto a 150-inch screen size.:

Note

The projection distances listed here involve an error of ±5 %. When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied size.

Setting up

- ENGLISH

Getting Started

For the screen aspect ratio of 16 : 9 (Unit : m)

Model number of

Screen dimensions Projection distance (L)

Screen size (")

70 0.872 1.550 2.26 3.02 3.06 4.60 4.61 7.74 7.75 12.40 12.12 23.06

80 0.996 1.771 2.60 3.47 3.51 5.27 5.28 8.86 8.87 14.18 13.90 26.41

90 1.121 1.992 2.93 3.92 3.95 5.95 5.96 9.99 9.99 15.97 15.69 29.76 100 1.245 2.214 3.27 4.36 4.40 6.62 6.63 11.11 11.11 17.76 17.47 33.10 120 1.494 2.657 3.93 5.26 5.30 7.96 7.97 13.35 13.36 21.33 21.04 39.79 150 1.868 3.321 4.94 6.60 6.64 9.98 9.99 16.72 16.73 26.68 26.40 49.83 200 2.491 4.428 6.61 8.83 8.89 13.34 13.35 22.34 22.34 35.61 35.33 66.56 250 3.113 5.535 8.28 11.06 11.13 16.70 16.71 27.95 27.96 44.54 44.26 83.29 300 3.736 6.641 9.95 13.29 13.37 20.07 20.08 33.57 33.57 53.47 53.19 100.02 350 4.358 7.748 11.62 15.52 15.61 23.43 23.44 39.18 39.19 62.40 62.12 116.75 400 4.981 8.855 13.29 17.76 17.85 26.79 26.80 44.80 44.80 71.33 71.05 133.48 500 6.226 11.069 16.63 22.22 22.33 33.51 33.52 56.03 56.03 89.19 88.91 166.95 600 7.472 13.283 19.97 26.69 26.82 40.24 40.25 67.26 67.26 107.04 106.77 200.41

Lens type Zoom lens

projection lens

Throw ratio

Effective

height

(SH)

Effective

width (SW)

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8

1.5–2.0 : 1 2.0–3.0 : 1 3.0–5.0 : 1 5.0–8.0 : 1 8.0–15.0 : 1

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Lens type Zoom lens Fixed-focus lens

Model number of

projection lens

(SH)

Effective

width (SW)

Throw ratio

Screen dimensions Projection distance (L)

Screen size (")

100 1.245 2.214 2.20 2.63 3.08 3.98 3.96 5.76 5.72 11.14 1.64 120 1.494 2.657 2.65 3.17 3.71 4.79 4.77 6.94 6.89 13.40 1.98 150 1.868 3.321 3.33 3.98 4.66 6.02 5.98 8.70 8.64 16.80 2.50 200 2.491 4.428 4.45 5.33 6.24 8.06 8.01 11.64 11.56 22.46 3.36 250 3.113 5.535 5.58 6.68 7.82 10.11 10.03 14.58 14.47 28.11 4.22 300 3.736 6.641 6.71 8.03 9.40 12.15 12.05 17.51 17.39 33.77 5.08 350 4.358 7.748 7.84 9.38 10.98 14.19 14.07 20.45 20.31 39.43 400 4.981 8.855 8.96 10.73 12.56 16.23 16.10 23.39 23.23 45.09 500 6.226 11.069 11.22 13.43 15.72 20.32 20.14 29.27 29.06 56.40 600 7.472 13.283 13.47 16.14 18.88 24.41 24.18 35.15 34.90 67.72

Effective

height

70 0.872 1.550 1.52 1.82 2.13 2.75 2.75 4.00 3.97 7.74 1.12

80 0.996 1.771 1.75 2.09 2.44 3.16 3.15 4.59 4.55 8.88 1.29

90 1.121 1.992 1.97 2.36 2.76 3.57 3.56 5.17 5.14 10.01 1.47

ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5

1.0–1.2 : 1 1.4–1.8 : 1 1.8–2.6 : 1 2.6–5.1 : 1 0.8 : 1

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Fixed

The throw ratio is based on the value during projection onto a 150-inch screen size.:

Note

The projection distances listed here involve an error of ±5 %.

When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied

size.

Setting up

ENGLISH -

Getting Started

Projection distance by projection lens (for PT-DW8300U)

For the screen aspect ratio of 16 : 9 (Unit : m)

Lens type Zoom lens

Model number of

projection lens

(SH)

Effective

width (SW)

Throw ratio

Screen dimensions Projection distance (L)

Screen size (")

100 1.245 2.214 3.35 4.48 4.52 6.79 6.80 11.39 11.40 18.21 17.92 33.94 120 1.494 2.657 4.03 5.39 5.44 8.17 8.18 13.69 13.70 21.87 21.58 40.80 150 1.868 3.321 5.06 6.76 6.81 10.23 10.24 17.15 17.15 27.36 27.08 51.09 200 2.491 4.428 6.77 9.05 9.11 13.68 13.69 22.90 22.91 36.51 36.23 68.25 250 3.113 5.535 8.49 11.34 11.41 17.13 17.14 28.66 28.67 45.67 45.39 85.40 300 3.736 6.641 10.20 13.63 13.71 20.57 20.58 34.42 34.42 54.82 54.54 102.55 350 4.358 7.748 11.91 15.92 16.00 24.02 24.03 40.17 40.18 63.97 63.70 119.70 400 4.981 8.855 13.63 18.21 18.30 27.47 27.48 45.93 45.93 73.13 72.85 136.85 500 6.226 11.069 17.05 22.78 22.90 34.36 34.37 57.44 57.45 91.43 91.16 171.16 600 7.472 13.283 20.48 27.36 27.49 41.25 41.26 68.95 68.96 109.74 109.47 205.46

Effective

height

70 0.872 1.550 2.32 3.10 3.14 4.72 4.73 7.94 7.94 12.71 12.43 23.65 80 0.996 1.771 2.66 3.56 3.60 5.41 5.42 9.09 9.09 14.54 14.26 27.08 90 1.121 1.992 3.01 4.02 4.06 6.10 6.11 10.24 10.25 16.37 16.09 30.51

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8

1.5–2.0 : 1 2.1–3.1 : 1 3.1–5.2 : 1 5.2–8.2 : 1 8.2–15.4 : 1

Min. (LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Lens type Zoom lens Fixed-focus lens

Model number of

projection lens

(SH)

Effective

width (SW)

Throw ratio

Screen dimensions Projection distance (L)

Screen size (")

100 1.245 2.214 2.25 2.70 3.15 4.08 4.06 5.91 5.87 11.42 1.68 120 1.494 2.657 2.72 3.25 3.80 4.92 4.89 7.11 7.07 13.74 2.03 150 1.868 3.321 3.41 4.08 4.78 6.17 6.14 8.92 8.86 17.22 2.56 200 2.491 4.428 4.56 5.47 6.40 8.27 8.21 11.93 11.85 23.03 3.44 250 3.113 5.535 5.72 6.85 8.02 10.36 10.28 14.95 14.84 28.83 4.33 300 3.736 6.641 6.87 8.24 9.64 12.46 12.36 17.96 17.83 34.63 5.21 350 4.358 7.748 8.03 9.62 11.26 14.55 14.43 20.97 20.82 40.43 400 4.981 8.855 9.18 11.01 12.88 16.65 16.50 23.98 23.81 46.23 500 6.226 11.069 11.49 13.78 16.12 20.83 20.65 30.01 29.80 57.83 600 7.472 13.283 13.80 16.55 19.36 25.02 24.80 36.03 35.78 69.43

Effective

height

70 0.872 1.550 1.56 1.87 2.18 2.82 2.82 4.10 4.07 7.94 1.15 80 0.996 1.771 1.79 2.14 2.51 3.24 3.23 4.70 4.67 9.10 1.33 90 1.121 1.992 2.02 2.42 2.83 3.66 3.65 5.31 5.27 10.26 1.50

ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5

1.0–1.2 : 1 1.4–1.9 : 1 1.8–2.7 : 1 2.7–5.2 : 1 0.8 : 1

Min. (LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Fixed

z z

The throw ratio is based on the value during projection onto a 150-inch screen size.:

Note

The projection distances listed here involve an error of ±5 %. When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied size.

Setting up

- ENGLISH

Getting Started

For the screen aspect ratio of 4 : 3 (Unit : m)

Model number of

Screen dimensions Projection distance (L)

Screen size (")

70 1.067 1.422 2.86 3.82 3.86 5.80 5.81 9.74 9.75 15.59 15.30 29.04

80 1.219 1.626 3.28 4.38 4.42 6.65 6.66 11.15 11.16 17.83 17.55 33.24

90 1.372 1.829 3.70 4.94 4.98 7.49 7.50 12.56 12.57 20.07 19.79 37.44 100 1.524 2.032 4.12 5.50 5.55 8.33 8.34 13.97 13.98 22.31 22.03 41.64 120 1.829 2.438 4.96 6.62 6.67 10.02 10.03 16.79 16.80 26.79 26.51 50.04 150 2.286 3.048 6.21 8.30 8.36 12.55 12.56 21.02 21.03 33.52 33.24 62.64 200 3.048 4.064 8.31 11.11 11.17 16.77 16.78 28.07 28.07 44.72 44.44 83.63 250 3.810 5.080 10.41 13.91 13.99 20.99 21.00 35.12 35.12 55.93 55.65 104.63 300 4.572 6.096 12.51 16.71 16.80 25.21 25.22 42.16 42.17 67.14 66.86 125.63 350 5.334 7.112 14.60 19.51 19.61 29.43 29.44 49.21 49.22 78.34 78.07 146.63 400 6.096 8.128 16.70 22.31 22.43 33.65 33.66 56.26 56.26 89.55 89.28 167.63 500 7.620 10.160 20.89 27.92 28.05 42.09 42.10 70.35 70.36 111.96 111.69 209.62 600 9.144 12.192 25.09 33.52 33.68 50.53 50.54 84.45 84.45 134.38 134.11 251.62

Lens type Zoom lens

projection lens

Throw ratio

Effective

height

(SH)

Effective

width (SW)

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8

2.0–2.7 : 1 2.7–4.1 : 1 4.1–6.9 : 1 6.9–11.0 : 1 10.9–20.6 : 1

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Lens type Zoom lens Fixed-focus lens

Model number of

projection lens

(SH)

Effective

width (SW)

Throw ratio

Screen dimensions Projection distance (L)

Screen size (")

100 1.524 2.032 2.77 3.32 3.88 5.02 4.99 7.26 7.21 14.03 2.08 120 1.829 2.438 3.34 4.00 4.68 6.05 6.01 8.74 8.68 16.87 2.51 150 2.286 3.048 4.19 5.01 5.87 7.58 7.53 10.95 10.87 21.13 3.16 200 3.048 4.064 5.60 6.71 7.85 10.15 10.07 14.64 14.53 28.23 4.24 250 3.810 5.080 7.01 8.40 9.83 12.71 12.61 18.32 18.20 35.33 5.32 300 4.572 6.096 8.43 10.10 11.82 15.28 15.15 22.01 21.86 42.43 6.40 350 5.334 7.112 9.84 11.80 13.80 17.84 17.68 25.70 25.52 49.53 400 6.096 8.128 11.26 13.49 15.78 20.40 20.22 29.39 29.18 56.64 500 7.620 10.160 14.08 16.88 19.75 25.53 25.30 36.76 36.50 70.84 600 9.144 12.192 16.91 20.27 23.72 30.66 30.38 44.14 43.83 85.04

Effective

height

70 1.067 1.422 1.92 2.30 2.69 3.48 3.47 5.05 5.01 9.77 1.43

80 1.219 1.626 2.21 2.64 3.09 3.99 3.98 5.78 5.75 11.19 1.64

90 1.372 1.829 2.49 2.98 3.49 4.51 4.49 6.52 6.48 12.61 1.86

ET-D75LE6 ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE5

1.4–1.6 : 1 1.9–2.5 : 1 2.5–3.6 : 1 3.6–6.9 : 1 1.0 : 1

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Min.

(LW)

Max.

(LT)

Fixed

The throw ratio is based on the value during projection onto a 150-inch screen size.:

Note

The projection distances listed here involve an error of ±5 %.

When geometric adjustment is used, compensation is made so that the screen size becomes smaller than the specied

size.

+ 99 hidden pages