Panasonic PT-DW7000E, PT-D7700E User Manual

DLPTMBased Projector Commercial Use

Operating Instructions

Read these instructions completely before operating this unit.

TQBJ 0147-3

POWER

ON OFF

RGB1RGB

AUX

STD

LENS

OSD

USER

LIGHT

ID ALL

ASPECT

ID SET

Projector

Computer

Numetric

BRIGHT

CONTRAST

ON SCREEN

SYSTEM

SEL

FUNC

D.ZOOM

ENTER

PAGE UP

PAGE DOWN

VIDEO

SHUT

S-

VIDEO

FREEZE

SHUTTER

AUTO SETUP

LASER ON/OFF

Model No.

PT-D7700E

PT-DW7000E

ENGLISHDEUTSCHFRANÇAISESPAÑOLITALIANO

Dear Panasonic Customer:

This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLP

based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required.

Model number: PT-D7700E / PT-DW7000E

Serial number:

IMPORTANT SAFETY NOTICE

WARNING: THIS APPARATUS MUST BE EARTHED.

WARNING: To prevent damage which may result in fire or shock hazard, do not expose

this appliance to rain or moisture.

Machine Noise Information Ordinance 3. GSGV, January 18 1991: The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779.

WARNING:

1) Remove the plug from the wall outlet when this unit is not in use for a prolonged period of time.

2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel.

3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three prong earthingtype power plug. This plug will only fit an earthing-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the earthing plug.

CAUTION:

To assure continued compliance, follow the attached installation instructions, which include using the shielded interface cables when connecting to a computer or peripheral device.

ENGLISH

IMPORTANT: THE MOULDED PLUG (U.K. only)

FOR YOUR SAFETY

, PLEASE READ THE FOLLOWING TEXT CAREFULLY

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSl to BS1362. Check for the ASTA mark or the BSl mark on the body of the fuse. If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from an Authorized Service Centre. If the fitted moulded plug is unsuitable for the socket outlet in your home, then the fuse

should be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

WARNING: –THIS APPLIANCE MUST BE EARTHED. IMPORTANT: –The wires in this mains lead are coloured in accordance with the following code: –

Green-and-Yellow: Earth Blue: Neutral Brown: Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

How to replace the fuse. Open the fuse compartment with a screwdriver and replace the fuse.

FUSE

Adjusting the position .............................................51

Shift adjustment...............................................................51

Size adjustment...............................................................52

Clock phase adjustment ..................................................53

Keystone distortion correction .........................................54

How to use ADVANCED MENU ...............................55

DIGITAL CINEMA REALITY ...........................................55

Blanking adjustment ........................................................56

Adjusting the input resolution ..........................................57

Adjusting the clamp position............................................58

Edge blending adjustment...............................................59

Raster position ................................................................61

Changing the display language ..............................62

How to change the system format..........................63

Option settings.........................................................64

ID number setting ............................................................64

Installation Setting ...........................................................65

Lamp select .....................................................................66

Lamp power.....................................................................66

RS232C SETTING (Procedure of setting

communication conditions)..............................................67

Position of on-screen indications.....................................67

System information..........................................................67

Adjusting colour matching ...............................................68

Adjusting the colour matching using a colorimeter..........69

Video setting....................................................................70

DVI EDID (Only when the ET-MD77DV

input module is installed).................................................70

Automatic adjustment......................................................70

Output resolution (D7700E only) .....................................71

Auto signal.......................................................................71

Fan control ......................................................................71

P IN P ..............................................................................72

Setting FUNC1 ................................................................73

Password.........................................................................73

Using the serial terminals .......................................74

Examples of connection .................................................74

Pin assignments and signal names.................................74

Communication conditions (Factory setting) ...................74

Basic format ....................................................................74

Control commands ..........................................................75

Cable specifications ........................................................75

Using the REMOTE 2 terminal ................................76

Displaying the internal test pattern ........................77

Cycle of displayed internal test patterns..........................77

RS-422 control functions.........................................77

Setting the security..................................................78

Setting the password.......................................................78

Changing the password...................................................79

Setting the text ................................................................79

Changing the text ............................................................79

How to use CP OPTION ...........................................80

Setting the on-screen indication function ........................80

Setting the system format................................................81

How to use network function (optional).................82

Initial setting of network function .....................................83

Accessing from the Web browser....................................85

Returning the network function setting

back to the factory setting ...............................................95

Indication of monitor lamp ......................................96

Cleaning and replacement of air filter....................97

Procedure of cleaning .....................................................97

Replacement of lamp unit .......................................98

Timing of lamp unit replacement .....................................98

Procedure of lamp unit replacement ...............................99

Before asking for service ......................................101

Specifications.........................................................102

Appendix.................................................................104

Outside dimensions...............................................105

Contents

IMPORTANT SAFETY NOTICE ..................................2

Precautions with regard to safety ............................5

Accessories ................................................................7

Precautions on handling ...........................................8

Examples of system expansion................................9

Name and function of parts.....................................10

Remote control ................................................................10

Front and side of the projector ........................................12

Rear view of the main unit...............................................13

Controls on rear panel.....................................................13

Side-mounted connection terminals ................................14

Using the remote control unit .................................15

Loading dry cells .............................................................15

Effective range of remote control operation ....................15

Setting projector ID number to remote control ................16

Using the remote control as a PC mouse........................17

Using a wired remote control...........................................17

Installation ................................................................18

Adjusting the leveling feet ...............................................18

Projection scheme...........................................................18

Installation geometry .......................................................18

Projection distances by the type of projection lenses (optional)

..19

Connection ...............................................................22

Before starting connection...............................................22

Example of connecting with VIDEO devices ...................23

Example of connecting with personal computers ............24

Example of connecting with the signal selector...............25

Installation of input module (optional)...................26

Installing the input module...............................................26

Connecting signals to the input module ..........................28

Connecting the signal to the SD-SDI input module .........29

Connecting the signal to the HD/SD-SDI input module...30

Connecting signals to the DVI-D input module................31

How to install and remove the projection lens (optional)

...32

How to install the projection lens.....................................32

How to remove the projection lens ..................................32

Projection..................................................................33

Powering up the projector ...............................................33

Making adjustment and selection ....................................33

Powering off the projector ...............................................34

How to adjust the lens .............................................35

How to adjust the lens focus, lens zoom and lens shift (optical shift)

..35

Adjustment range after lens position (optical shift)..........35

How to adjust the lens for addressing unevenness of focusing

..36

Automatic adjustment (AUTO SETUP)...................37

Registration of input signal data ............................38

Registration of new data..................................................38

Renaming the registered signals.....................................38

Clearing the data of registered signals

...............................

Sub memory ....................................................................40

Using the FREEZE function ....................................42

Using the SHUTTER function..................................42

Using the digital zoom (– D.ZOOM +) function ...............

On-screen menus.....................................................43

Structure of menu screens ..............................................43

Basic operations on menu screen ...................................44

Returning to the previous screen ....................................44

Menu items shown in gray characters.............................44

Menu items setting ..........................................................44

Resetting to the factory default........................................44

Adjusting the picture ...............................................45

Switching the picture mode .............................................45

Adjusting Contrast / Bright / Colour / Tint ........................46

Registering the picture mode settings as presettings......47

DYNAMIC IRIS setting ....................................................48

Adjusting the colour temperature ....................................49

Sharpness / Gamma / Noise reduction ...........................50

To display pictures complying with the sRGB standard ..50

ENGLISH

Precautions with regard to safety WARNING

If a problem occurs (such as no image) or if you notice smoke or a strange smell coming from the projector, turn off the power and disconnect the power cord from the wall outlet.

• Do not continue to use the projector in such cases, otherwise fire or electric shocks could result.

• Check that no more smoke is coming out, and then contact an Authorized Service Centre for repairs.

• Do not attempt to repair the projector yourself, as this can be dangerous.

Do not install this projector in a place which is not strong enough to take the full weight of the projector.

• If the installation location is not strong enough, it may fall down or tip over, and severe injury or damage could result.

• Installation work (such as ceiling suspension) should only be carried out by a qualified technician.

• If installation is not carried out correctly, there is the danger that injury or electric shocks may occur.

If foreign objects or water get inside the projector, or if the projector is dropped or the cabinet is broken, turn off the power and disconnect the power cord from the wall outlet.

• Continued use of the projector in this condition may result in fire or electric shocks.

• Contact an Authorized Service Centre for repairs.

Do not cover the air filter, the air inlet and exhaust vents.

• Doing so may cause the projector to overheat, which can cause fire or damage to the projector.

Do not overload the wall outlet.

• If the power supply is overloaded (for example, by using too many adapters), overheating may occur and fire may result.

Do not remove the cover or modify it in any way.

• High voltages which can cause fire or electric shocks are present inside the projector.

• For any inspection, adjustment and repair work, please contact an Authorized Service Centre.

Clean the power cord plug regularly to prevent it from becoming covered in dust.

• If dust builds up on the power cord plug, the resulting humidity can damage the insulation, which could result in fire. Pull the power cord out from the wall outlet and wipe it with a dry cloth.

• If not using the projector for an extended period of time, pull the power cord plug out from the wall outlet.

Do not do anything that might damage the power cord or the power cord plug.

• Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.

• If the power cord is used while damaged, electric Shocks, short-circuits or fire may result.

• Ask an Authorized Service Centre to carry out any repairs to the power cord that might be necessary.

Do not handle the power cord plug with wet hands.

• Failure to observe this may result in electric shocks.

Insert the power cord plug securely into the wall outlet.

• If the plug is not inserted correctly, electric shocks or overheating could result.

• Do not use plugs which are damaged or wall outlets which are coming loose from the wall.

Do not place the projector on top of surfaces which are unstable.

• If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over, and injury or damage could result.

Do not place the projector into water or let it become wet.

• Failure to observe this may result in fire or electric shocks.

Do not disassemble the lamp unit.

• If the lamp section breaks, it may cause injury.

Precautions with regard to safety

Do not place liquid containers on top of the projector.

• If water spills onto the projector or gets inside it, fire or electric shocks could result.

• If any water gets inside the projector, contact an Authorized Service Centre.

Do not insert any foreign objects into the projector.

• Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, as doing so can result in fire or electric shocks.

After removing the battery from remote control unit, keep it away from the reach of children.

• The battery can cause death by suffocation if swallowed.

• If the battery is swallowed, seek medical advice immediately.

Do not allow the + and - terminals of the battery to come into contact with metallic objects such as necklaces or hairpins.

• Failure to observe this may cause the battery to leak, overheat, explode or catch fire.

• Store the battery in a plastic bag and keep it away from metallic objects.

Insulate the battery using tape or similar before disposal.

• If the battery comes into contact with metallic objects or other batteries, it may catch fire or explode.

Replacement of the lamp unit should only be carried out by a qualified technician.

• The lamp unit has high internal pressure. If improperly handled, failure might result.

• The lamp unit can easily become damaged if struck against hard objects or dropped, and injury or malfunctions may result.

Do not set up the projector in humid or dusty places or in places where the projector may come into contact with smoke or steam.

• Using the projector under such conditions may result in fire or electric shocks.

When disconnecting the power cord, hold the plug, not the cord.

• If the power cord itself is pulled, the cord will become damaged, and fire, short-circuits or serious electric shocks may result.

Always disconnect all cables before moving the projector.

• Moving the projector with cables still attached can damage the cables, which could cause fire or electric shocks to occur.

Do not place any heavy objects on top of the projector.

•

Failure to observe this may cause the projector to become unbalanced and fall, which could result in damage or injury.

Do not short-circuit, heat or disassemble the battery or place it into water or fire.

• Failure to observe this may cause the battery to overheat, leak, explode or catch fire, and burns or other injury may result.

When inserting the battery, make sure the polarities (+ and -) are correct.

• If the battery is inserted incorrectly, it may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result.

Use only the Specified battery.

• If an incorrect battery is used, it may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result close to this port, otherwise burns or damage could result.

Caution

ENGLISH

Accessories

Check that all of the accessories shown below have been included with your projector.

Do not look into the lens while the projector is being used.

•

Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes.

Do not bring your hands or other objects close to the air outlet port.

•

Heated air comes out of the air outlet port. Do not bring your hands or face, or objects which cannot withstand heat.

Do not use the old lamp unit.

• The lamp section may break.

Replacement of the lamp unit should only be carried out after it has completely cooled off, otherwise burns may result.

Disconnect the power cord plug from the wall outlet as a safety precaution before carrying out any cleaning.

• Electric shocks can result if this is not done.

Ask an Authorized Service Centre to clean inside the projector at least once a year.

• If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation.

• It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your nearest Authorized Service Centre to clean the projector when required. Please discuss with the Authorized Service Centre regarding cleaning costs.

Do not reach for the openings beside the optical lens, during horizontal or vertical movements of the lens there is a injury hazard.

An effort to keep our environment clean, Please bring the non repairable unit your Dealer or a Recycling Company.

Remote control: [N2QAGB000024 x 1]

POWER

ON OFF

RGB1RGB

AUX

STD

LENS

OSD

USER

LIGHT

ID ALL

ASPECT

ID SET

Projector

Computer

Numetric

BRIGHT

CONTRAST

ON SCREEN

SYSTEM

SEL

FUNC

D.ZOOM

ENTER

PAGE UP

PAGE DOWN

VIDEO

SHUT

S-

VIDEO

FREEZE

SHUTTER

AUTO

SETUP

LASER ON/OFF

Power cord: Wired cable for remote

control: [15m, K1EA03NA0001 x 1]

Dry batteries for remote control (AA):

for U.K. [K2CT3FZ00003 x 1]

for Continental [K2CM3FZ00003 x 1]

Precautions on handling

Precautions on transport

The projection lens is susceptible to vibrations and impacts. Be sure to always remove the lens during transport.

Precautions on installation

Be sure to observe the following precautions when installing the product.

Avoid installing the product in a place exposed to vibrations or impacts

If the projector is installed in a place where vibrations are transmitted from a source of driving power and others or mounted in a car or a vessel, vibrations or impacts may be transmitted to the product to damage the internal parts, causing failure. Install the product in a place free from vibrations and impacts.

Do not install the projector near highvoltage power lines or power sources.

The product may be exposed to interference if it is installed in the vicinity of high-voltage electrical power lines or power sources.

Do not place the projector on a vinyl sheet or carpet.

If a vinyl sheet sucked up and blocks the air filter intake port, the internal temperature of the projector may increase, which triggers the protection circuit, turning off the power.

Be sure to ask a specialized technician when to install the product to a ceiling.

If the product is to be installed hanging from the ceiling, purchase an optional hanging attachment (for high ceiling: Model No. ET-PKD75) (for low ceiling: Model No. ET-PKD75S) and call a specialized technician for installation.

Do not place the projector over 2 700 m above sea level. When using it over 1 400 m above sea level, set the “Fan Control”, described on page 71, to “HIGHLAND”.

Otherwise the life of the product may be shortened.

Precautions on use

To view clear images:

• The audience cannot enjoy high-contrast and clear images if outside light or the illumination interferes the screen surface.Draw window curtains or blinds, turn off the lightings near the screen or take other proper measures.

• In rare cases, wafture can occur on the screen affected by the warm air from the exhaust port depending on the environment.

Do not touch the surface of the projection lens with bare hand.

If fingerprints or stains are left on the projection lens surface, they are magnified and projected on the screen. Keep your hands away from the lens. Cover the lens with the supplied lens cap when the projector is not used.

Screen

If the screen has stains, flaws or discoloration, clear images cannot be viewed. When handling the screen, be careful not to apply volatile substances or leave flaws or stains on the screen.

Lamp

A mercury lamp with high internal pressure is used for the light source of this product. A high-pressure mercury lamp has the following characteristics:

• It may burst with a loud sound or end its life cycle by not illuminating because of given impacts, flaws, or deterioration due to used hours.

• The life cycle of a mercury lamp varies according to the individual difference or conditions of use. In particular, turning the power on and off frequently and/or repeatedly will greatly affect the life cycle.

• In rare cases, it may burst shortly after the first lighting.

• The possibility of burst increases when the lamp is used beyond the replacement time.

Disposal

To discard the product, call the dealer or a specialized dealer.

Cleaning and maintenance

Be sure to remove the power cord plug from the receptacle before cleaning.

Use soft and dry cloth to clean the cabinet

If stains are hard to remove, use a cloth dampened with a kitchen detergent solution (neutral) and squeezed to wipe the cabinet and finish with a dry cloth. If a chemical wipe is used, follow its instructions.

Do not clean the lens surface with fuzzy or dusty cloth.

If dust adheres to the lens, it will be magnified and projected on the screen. Use a soft and clean cloth to wipe off dust.

ENGLISH

The projector is provided with a number of terminals and optional accessories to enable various system expansions. Both input and output are provided to all terminals on the main unit. The following are some examples of system expansion:

Examples of system expansion

System 1

Stacking two projectors with the stacking brackets can double the picture brightness.

System 3

PC equipped with a DVI-D input module (an optional item) can be attached to the projector for computer image viewing (Realization of high-resolution picture.)

System 2

The optional high- or low-ceiling mount bracket flexibly fits the projector in individual site conditions.

System 4

Connection of a signal selector enables to feed a variety of video sources to the projector.

O F

POWER

O N

N P

U T

S E

L E

C T

V P O N /

F F

S i

n a l

S e l

e c t

r T W

S W

Digital broadcasting tuner or DVD player

Control PC

Signal selector

(Option)

Video deck

Name and function of parts

< When the operation mode selector is

set to Projector >

Remote control operation indicator lamp

The lamp flashes when any remote control button is pressed.

POWER ON button (page 33)

Turns on the power if the MAIN POWER has been put to the “l” position.

POWER OFF button (page 34)

Turns off the power if the MAIN POWER has been put to the “l” position.

AUTO SET UP button (page 37)

Pressing this button while projecting an image automatically corrects the picture positioning on the screen. While the auto setup feature is active, a message “PROGRESS...” appears on the screen.

Input selector (RGB1, RGB2, AUX, VIDEO, S-VIDEO) button

Use to toggle through the RGB1, RGB2, AUX (module input), VIDEO and S-VIDEO input ports.

SHUTTER button (page 42)

Press this button to black out the image temporarily.

MENU button (page 44)

Displays and clears the Main Menu. It can also return to the previous screen when the menu is displayed.

FREEZE button (page 42)

Press this button to freeze the image temporarily.

Arrow buttons (page 44)

Use these buttons to select an item on the menu screen, change setting and adjust the level. Also use them to enter the “SECURITY” password.

ENTER button (page 44)

Press this button to enter your menu selection or to run function.

ON SCREEN button

This button turns on and off the on-screen indication function.

Standard (STD) button (page 44)

Press this button to restore the default factory setting

SYSTEM SELECTOR button (page 63)

System switching can be done.

Function 1 (FUNC1) button (page73)

This button can control the functions set in “FUNC1” of the “Option” screen from Main Menu.

Digital Zoom (- D.ZOOM +) buttons (page 42)

Any portion of the picture can be zoomed in.

LENS button (page 35)

Switches to the mode of projection lens adjustment.

CONTRAST button (page 46)

Switches to the mode of image contrast adjustment.

BRIGHT button (page 46)

Switches to the mode of black level adjustment.

NEXT button

When multiple signal selectors are connected to the main unit in the system, this button specifies the second signal selector or beyond. With the ID set button pressed, every press on the button will change the value in the ten’s place.

ASPECT button

Switches the image aspect ratio to 4:3, 16:9.

Remote control

POWER

ON OFF

RGB1RGB

AUX

STD

LENS

OSD

USER

LIGHT

ID ALL

ASPECT

ID SET

Projector

Computer

Numetric

BRIGHT

CONTRAST

ON SCREEN

SYSTEM

SEL

FUNC

D.ZOOM

ENTER

PAGE UP

PAGE DOWN

VIDEO

SHUT

S-

VIDEO

FREEZE

SHUTTER

AUTO

SETUP

LASER ON/OFF

ENGLISH

LIGHT button ( Click button)

When this button is pressed, the remote control button light is turned on.The light goes off about 30 seconds after you stop remote control operation.

USER button

Displays the sub-memory screen of the signal registration.

ID ALL button (pages 16, 64)

When two or more main units are used in the system, this button switches to the mode to control them simultaneously with a single remote control.

ID SET button (pages 16, 64)

When two or more main units are used in the system, this button specifies the ID of the remote control.

Remote control wired terminal (page 17)

To use the wired output terminal, connect the remote control and the main unit with the supplied cable.

Remote control transmitter window

Operate the remote control aiming at the remote control receiver window on the main unit.

ON OFF

<When the operation mode selector is

set to Computer>

PAGE UP/PAGE DOWN buttons

These buttons correspond to the PAGE UP/PAGE DOWN buttons on PC's keyboard.

( ) buttons (page 17)

These buttons correspond to the left and right mouse buttons.

ENTER button

Moves the mouse cursor.

Numeric (0-9) buttons

In a system that uses two or more units of this projector or in a system that connects to an optional signal selector, these buttons specify a particular projector unit or the input of the signal selector. They are also used to input the ID number when selecting the ID and to enter the password when the password for service personnel needs to be entered.

Operation mode selector (Computer/Numeric, Projector) switch (page 17)

Put this selector to the right position to control the projector and to the left position to control the PC or use numeric buttons.

Click button (page 17)

This button corresponds to the left mouse button when the operation mode is switched to the Computer position.

• To use the remote control as a mouse, please purchase an optional wireless mouse receiver (model No.: ET-RMRC2).

• The AUX button to switch the input is disabled when an optional input module is not connected.

Note

RGB1RGB

VIDEO

STD

FUNC

LENS

LIGHT

Computer

Numetric

POWER

AUTO

SETUP

AUX

SHUTTER

S-

VIDEO

SHUT

FREEZE

PAGE UP

ENTER

PAGE DOWN

ON SCREEN

SYSTEM

OSD

SEL

D.ZOOM

CONTRAST

BRIGHT

USER

ASPECT

ID ALL

ID SET

LASER ON/OFF

Projector

D I

SETUP

AUTO

Projector

E R

Computer

Side-mounted connection terminals (page 14)

AC IN terminal (page 33)

Connect the supplied line power cord into this receptacle. Do not connect any other cable to this socket.

MAIN POWER switch (page 33)

Use this switch to turn on “I” and off “

” the

commercial line power applied to the projector.

Burglar lock

Attach a commercial burglar prevention cable (e.g., from Kensington) to this lock port. It is compatible with the Microsaver Security System from Kensington. Contact details for this company are given below. Kensington Technology Group ACCO Brands Inc. 2885 Campus Drive San Mateo, CA94403 Tel (650)572-2700 Fax (650)572-9675 http://www.kensington.com/ http://www.gravis.com/

Remote control receiver window (front) (page 15)

This window receives the signal beam emitted from the remote control.

Power indicator lamp (page 33)

The lamp lights in red when the MAIN POWER switch is turned to “I” (on). It turns to green when the POWER ON button of the remote control or the main unit is pressed.

LAMP1 monitor (page 96)

This lamp lights up when the time to replace lamp unit 1 is reached. It also blinks if something unusual occurs in the lamp circuit.

Projection lens (optional)

Lens for projecting images on the screen.

Projection lens cover lock button

This button toggles between lock and unlock of the detachable cover for the projection lens (optional).

Temperature monitor (TEMP) (page 96)

Lighting or blinking of this lamp indicates an abnormal condition of the internal temperature.

LAMP2 monitor (page 96)

This lamp lights up when the time to replace lamp unit 2 is reached. It also blinks if something unusual occurs in the lamp circuit.

Air filter (page 97) Level-adjusting feet (page 18)

Use these feet to adjust the tilt of the projector. (Leveling feet are provided at the front and rear, right and left.)

Name and function of parts

Front and side of the projector

ENGLISH

Lamp unit cover

The lamp unit is housed.

Remote control receiver window (rear) (page 15)

This also receives the signal beam coming from the remote control.

POWER ON (I) button (page 33)

Turns on the power.

POWER OFF ( ) button (page 34)

Turns off the power.

AUTO SETUP button (page 37)

Pressing this button while projecting an image automatically corrects the picture positioning on the screen. While the auto setup feature is active, a message “EXECUTING...” appears on the screen.

RGB1 button (page 33)

Switches to RGB1 input.

RGB2 button (page 33)

Switches to RGB2 input.

AUX button (page 33)

Switches to optional input module input.

VIDEO button (page 33)

Switches to video input.

S-VIDEO button (page 33)

Switches to S-VIDEO input.

SHUTTER button (page 42)

Press this button to black out the image temporarily.

MENU button (pages 44 and 80–81)

Displays and clears the Main Menu. It can also return to the previous screen when the menu is displayed. Menus can be displayed by holding down the MENU button for at least 3 seconds while the onscreen indication function is OFF.

LENS button (page 35)

Switches to the adjustment mode for lens focus, zoom and shift (position).

ENTER button (page 44)

Press this button to enter your menu selection or to run function.

Arrow ( ) buttons (page 44)

Use to select an item on the menu screen, change setting and adjust the level. Also use them to enter the “SECURITY” password.

Rear view of the main unit Controls on rear panel

AUTO

SETUP

RGB 1

VIDEO

ENTER

LENS

S-VIDEO

SHUTTER

RGB 2

AUX

S-VIDEO IN terminal (pages 22 and 23)

An input terminal for S-video signals (MIN4-pin DIN). This terminal complies with S1 signals and automatically toggles between 16:9 and 4:3 according to the size of input signals.

VIDEO IN terminal (page 23)

An input terminal for video signals. (BNC)

VIDEO OUT terminal (page 23)

An output terminal (active through) for video signals. (BNC)

RGB (YPB

PR) 1 input terminal (pages 24, 25)

A terminal to input RGB or YPBPR signals (BNC).

RGB (YP

BPR) 2 input terminal (page 24)

A terminal to input RGB or YPBPR signals (D-SUB 15-pin female).

REMOTE1 lN/OUT terminal (page 17)

When two or more main units are used in the system, they can be connected and controlled with a wired remote control cable (M3 jack).

REMOTE2 terminal (page 76)

The user can remotely control the main unit by using an external control circuit to this terminal (D-SUB 9-pin female).

SERIAL IN terminal (pages 23–25, 67, 74, 75)

This terminal is an RS-232C/RS-422 compliant input terminal (switching necessary) to connect a PC and to externally control the main unit (D-SUB 9-pin female).

SERIAL OUT terminal (pages 24, 25, 67, 74, 75)

This terminal is an RS-232C/RS-422 compliant output terminal (switching necessary) to supply signals given to the serial input terminal (D-SUB 9-pin male).

SERIAL

S-VIDEO

RGB 2 IN

VIDEO

REMOTE 1

RGB 1 IN

OUT

SYNC/HD VDB/PBG/Y

REMOTE 2

R/PR

RS-232C (G) / RS-422 (R)RS-232C (G) / RS-422 (R)

Side-mounted connection terminals

Name and function of parts

ENGLISH

Loading dry cells

When loading supplied AA dry cells into the battery compartment of the remote control, make sure that their polarities are correct.

1. Open battery compartment lid.

Open the lid in the order of steps and .

2. Insert the dry cells.

Into battery compartment, with their polarities orientated as indicated ( , )in the

compartment.

3. Close the battery compartment lid.

Replace the battery compartment lid over the compartment and slide until it clicks.

Effective range of remote control operation

The remote control should normally be aimed at either the front or rear remote control receiver window on the projector (figure 1). Otherwise, it may also be aimed at the screen, which will reflect commands back to the projector's front receiver window as illustrated in figure 2.

The effective control range is approx. 7 metres from the beam receiver on the front or rear.

• Do not drop the remote control unit.

• Do not expose remote control unit to

any liquid.

• Do not use NiCd batteries.

Attention

• When the remote control is aimed at the screen, the effective control range may be reduced due to the optical loss by screen reflection.

• The remote control may not function properly if an object is in the light path.

• The remote control receiver may not function properly in intense ambient light such as fluorescent lamps. Carefully site the projector so its remote control receiver windows will not be directly exposed to intense light.

Supplied AA dry cells (insert the side first).

(Front) (Rear)

[Top view]

Remote control

30˚

[Side view]

15˚

Remote control

Screen

Projector

Remote control receiver window (front)

Remote control receiver window (rear)

Remote control

Using the remote control unit

Note

Figure 2

Figure 1

Every projector has its ID number and the ID number of the controlling projector must be set to the remote control in advance so that the user can operate the remote control. The ID number of the projector is set to “ALL” on

shipping, and use the ID ALL button of the remote control when using only a single projector.

Procedure of ID setting

Change the position of the operation mode selector switch to “Computer”. Press the ID SET button, and within five seconds, use the NEXT button to set the

number of the tens digit in the ID number, which is already set in the projector, and then use one of the numeric (0-9) buttons to set the number of the units digit.

Change the position of the operation mode selector switch to “Projector”.

However, if the ID ALL button is pressed, the projector can be controlled regardless of the ID number of the projector (simultaneous control mode).

Using the remote control unit

Setting projector ID number to remote control

• Do not press the ID SET button accidentally or carelessly because the ID number on the remote control can be set even when no projector is around. If the ID SET button is pressed, the ID number goes back to the one set before pressing the ID SET button unless the NEXT button and a numeric button are pressed within five seconds after the ID SET button is pressed.

• Your specified ID number is stored in the remote control unit unless another one is specified later. However, the stored ID will be erased if the batteries of the remote control are left exhausted. When the dry cells are replaced, set the same ID number again.

Attention

ENGLISH

Using the remote control as a PC mouse

Operation mode selector switch

Put the knob to the Computer position.

• ENTER button

Pressing the front, rear, left and right edges of the button moves the mouse cursor up, down, left and right.

• Right click ( ) button

This button can be used as the right mouse button.

• Left click ( ) button

This button can be used as the left mouse button.

• PAGE UP button

This button can be used as the Page Up button on the PC keyboard.

• PAGE DOWN button

This button can be used as the Page Down button on the PC keyboard.

• Click button

This button can be used as the left mouse button.

POWER

ON OFF

RGB1RGB

AUX

STD

LENS

OSD

USER

LIGHT

ID ALL

ASPECT

ID SET

Projector

Computer

Numetric

BRIGHT

CONTRAST

ON SCREEN

SYSTEM

SEL

FUNC

D.ZOOM

ENTER

PAGE UP

PAGE DOWN

VIDEO

SHUT

S-

VIDEO

FREEZE

SHUTTER

AUTO

SETUP

LASER ON/OFF

PAGE DOWN button

Operation mode selector switch

ENTER button

Right click ( ) button

PAGE UP button

Left click ( ) button

Projector

Computer

Click button

• To use the remote control as a mouse, please purchase an optional wireless mouse receiver (model No.: ET-RMRC2).

When multiple main units are connected in the system, connect the units with the supplied remote control cable to simultaneously control the multiple main units with a single remote control unit through the

SERIAL

S-VIDEO

RGB 2 IN / RGB 1 OUT

VIDEO

REMOTE 1

RGB 1 IN

OUT

SYNC/HD VDB/PBG/Y

REMOTE 2

R/PR

RS-232C (G) / RS-422 (R)RS-232C (G) / RS-422 (R)

POWER

ON OFF

RGB1RGB

AUX

STD

LENS

OSD

USER

LIGHT

ID ALL

ASPECT

ID SET

Projector

Computer

Numetric

BRIGHT

CONTRAST

ON SCREEN

SYSTEM

SEL

FUNC

D.ZOOM

ENTER

PAGE UP

PAGE DOWN

VIDEO

SHUT

S-

VIDEO

FREEZE

SHUTTER

AUTO

SETUP

LASER ON/OFF

Side-mounted terminals

Connect to the secondary projector

Remote control

Remote control cable (supplied)

Using a wired remote control

REMOTE1 IN/OUT terminal. It is effective to use the wired remote control in the environment in which an obstacle stands in the light path or where devices are susceptible to outside light.

Note

Projection scheme

This projector can use any of the four projection schemes shown at right. Select the scheme that best suits your particular installation location. Select the most suitable scheme to the situation of your location. Use the OPTION menu on the menu screen to choose the desired projection scheme. (Refer to page 65)

Installation

Adjusting the leveling feet

The four leveling feet mounted at the bottom of the projector are level-adjustable (0 mm–33 mm) which can be used when the floor surface is not horizontal.

Rear projection

Front projection

Table standing

Ceiling mount

Table standing

Ceiling mount

(Default position)

< Front > < Side >

Leveling feet

;

Side view

When optional ceiling mount bracket (ET-PKD75)

Screen

(unit: mm)

438-558

237

314

140

175

468

117

Top view

Screen

(unit: mm)

Installation geometry

When planning the projector and screen geometry, refer to the figures below and the information on the next page for reference. After the projector is roughly positioned, picture size and vertical picture positioning can be finely adjusted with the powered zoom lens and lens shifting mechanism.

L : Projection distance SH : Height of the image SW : Image width H : Vertical distance between the lens centre

level and the bottom edge of the projected image

For PT-D7700E: H = 0 to SH For PT-DW7000E: H = -0.18 x SH to 1.18 x SH

Lens Dimension of L1 (Approx.) ET-D75LE1 102 ET-D75LE2 86.5 ET-D75LE3 90 ET-D75LE4 113.9 ET-D75LE5 190 ET-D75LE8 242

ENGLISH

L : Projection distance SH : Effective screen height

Projection distances by the type of projection lenses (for PT-D7700E)

• For the screen aspect ratio of 4:3 Units: m

• The projection distances listed here involve an error of ±5%.

• Keystone distortions are corrected in the way the screen size becomes smaller than the original one.

Projection distances by the type of projection lenses (optional)

Every type of optional projection lenses has a different projection distance to achieve the same screen size. Select and purchase a projection lens most suitable to the size of your location referring to the following tables and the projection distances by the type of projection lenses on the next page.

Screen

size

(inch)

Screen

dimensions

70 80

90 100 120 150 200 250 300 350 400 500 600

1.066

1.219

1.371

1.524

1.828

2.286

3.048

3.810

4.572

5.334

6.096

7.620

9.144

1.422

1.625

1.828

2.032

2.438

3.048

4.064

5.080

6.096

7.112

8.129

10.160

12.192

Effective

width (SW)

1.02

1.18

1.34

1.50

1.81

2.29

3.08

3.87

4.66

-----

11.37

13.01

14.65

16.29

19.57

24.49

32.69

40.88

49.08

57.28

65.47

81.87

98.26

7.10

8.13

9.16

10.19

12.26

15.35

20.50

25.66

30.81

35.97

41.12

51.43

61.74

7.09

8.13

9.16

10.19

12.25

15.34

20.50

25.65

30.81

35.96

41.12

51.42

61.73

4.23

4.84

5.46

6.08

7.31

9.16

12.25

15.34

18.42

21.51

24.60

30.77

36.94

4.21

4.83

5.45

6.07

7.30

9.15

12.24

15.33

18.41

21.50

24.58

30.76

36.93

2.80

3.21

3.62

4.04

4.86

6.09

8.15

10.21

12.27

14.32

16.38

20.50

24.61

2.77

3.18

3.59

4.00

4.82

6.05

8.10

10.15

12.19

14.24

16.29

20.39

24.49

2.07

2.38

2.68

2.99

3.60

4.53

6.06

7.59

9.13

10.66

12.19

15.26

18.33

Minimum

Maximum

ET-D75LE1

(1.5-2.0 :1)

Minimum

Maximum

ET-D75LE2

(2.0-3.0 :1)

Minimum

Maximum

ET-D75LE3

(3.0-5.0 :1)

Minimum

Maximum

ET-D75LE4

(5.0-8.0 :1)

ET-D75LE5

(0.8 : 1)

Projection distance (L)

Zoom lens

Fixed-

focus lens

21.14

24.22

27.29

30.36

36.50

45.72

61.08

76.44

91.79

107.15

122.51

153.23

183.95

11.09

12.73

14.37

16.01

19.29

24.21

32.40

40.60

48.80

57.00

65.19

81.59

97.98

Minimum

Maximum

ET-D75LE8

(8.0-15.0 :1)

Effective

height

(SH)

Screen

size

(inch)

Screen

dimensions

90 100 120 150 200 250 300 350 400 500 600

0.871

0.996

1.120

1.245

1.494

1.868

2.491

3.113

3.736

4.358

4.981

6.226

7.472

1.549

1.771

1.992

2.214

2.657

3.321

4.428

5.535

6.641

7.748

8.855

11.069

13.282

Effective

width (SW)

1.12

1.29

1.47

1.64

1.98

2.50

3.36

4.22

5.08

-----

12.40

14.19

15.97

17.76

21.33

26.69

35.61

44.54

53.47

62.40

71.33

89.19

107.04

7.75

8.87

9.99

11.11

13.36

16.73

22.34

27.96

33.57

39.19

44.80

56.03

67.26

7.74

8.86

9.99

11.11

13.35

16.72

22.34

27.95

33.57

39.18

44.80

56.03

67.26

4.61

5.28

5.96

6.63

7.97

9.99

13.35

16.71

20.08

23.44

26.80

33.53

40.25

4.60

5.27

5.95

6.62

7.96

9.98

13.34

16.70

20.07

23.43

26.79

33.51

40.24

3.06

3.51

3.96

4.40

5.30

6.65

8.89

11.13

13.37

15.61

17.85

22.33

26.82

3.03

3.47

3.92

4.36

5.26

6.60

8.83

11.06

13.29

15.53

17.76

22.22

26.69

2.26

2.60

2.93

3.27

3.93

4.94

6.61

8.28

9.95

11.62

13.29

16.63

19.97

Minimum

Maximum

ET-D75LE1

(1.5-2.0 :1)

Minimum

Maximum

ET-D75LE2

(2.0-3.0 :1)

Minimum

Maximum

ET-D75LE3

(3.0-5.0 :1)

Minimum

Maximum

ET-D75LE4

(5.0-8.0 :1)

ET-D75LE5

(0.8 : 1)

Projection distance (L)

Zoom lens

Fixed-

focus lens

23.06

26.41

29.76

33.10

39.79

49.83

66.56

83.29

100.02

116.75

133.49

166.95

200.41

12.12

13.90

15.69

17.47

21.05

26.40

35.33

44.26

53.19

62.12

71.05

88.91

106.77

Minimum

Maximum

ET-D75LE8

(8.0-15.0 :1)

Effective

height

(SH)

Note

Screen

• For the screen aspect ratio of 16:9 Units: m

• The projection distances listed here involve an error of ±5%.

• Keystone distortions are corrected in the way the screen size becomes smaller than the original one.

Installation

Note

Projection distances by the type of projection lenses (for PT-DW7000E)

• For the screen aspect ratio of 16:9 Units: m

Screen

size

(inch)

Screen

dimensions

70 80

90 100 120 150 200 250 300 350 400 500 600

0.871

0.996

1.120

1.245

1.494

1.868

2.491

3.113

3.736

4.358

4.981

6.226

7.472

1.549

1.771

1.992

2.214

2.657

3.321

4.428

5.535

6.641

7.748

8.855

11.069

13.282

Effective

width

(SW)

1.15

1.33

1.50

1.68

2.03

2.56

3.45

4.33

5.21

-----

12.71

14.54

16.38

18.21

21.87

27.36

36.51

45.67

54.82

63.97

73.13

91.43

109.74

7.94

9.09

10.25

11.40

13.70

17.15

22.91

28.67

34.42

40.18

45.93

57.45

68.96

7.94

9.09

10.24

11.39

13.69

17.15

22.90

28.66

34.42

40.17

45.93

57.44

68.95

4.73

5.42

6.11

6.80

8.18

10.24

13.69

17.14

20.58

24.03

27.48

34.37

41.26

4.72

5.41

6.10

6.79

8.17

10.23

13.68

17.13

20.57

24.02

27.47

34.36

41.25

3.14

3.60

4.06

4.52

5.44

6.81

9.11

11.41

13.71

16.01

18.30

22.90

27.49

3.10

3.56

4.02

4.48

5.39

6.77

9.05

11.34

13.63

15.92

18.21

22.78

27.36

2.32

2.66

3.01

3.35

4.04

5.06

6.78

8.49

10.20

11.91

13.63

17.05

20.48

Minimum

Maximum

ET-D75LE1

(1.5-2.0 :1)

Minimum

Maximum

ET-D75LE2

(2.0-3.0 :1)

Minimum

Maximum

ET-D75LE3

(3.0-5.0 :1)

Minimum

Maximum

ET-D75LE4

(5.0-8.0 :1)

ET-D75LE5

(0.8 : 1)

Projection distance (L)

Zoom lens

Fixed-

focus lens

23.65

27.08

30.51

33.94

40.80

51.10

68.25

85.40

102.55

119.70

136.85

171.16

205.46

12.43

14.26

16.09

17.92

21.58

27.08

36.23

45.39

54.54

63.69

72.85

91.16

109.47

Minimum

Maximum

ET-D75LE8

(8.0-15.0 :1)

Effective

height

(SH)

Projection distances by the type of projection lenses (optional) (continuing)

ENGLISH

If the projector is used with a screen size not listed in this manual, check the diagonal dimension (inch) of your screen and calculate the projection distance using the following formulas.

Calculation formulas for projection distance by lens types (for PT-D7700E)

Minimal distance: L=0.1123 x Screen diagonal (inch) – 0.1158 Maximal distance: L=0.1786 x Screen diagonal (inch) – 0.1013

16:9

ET-D75LE5

(0.8:1)

Model number of projection lens

Aspect ratio

Projection distance (L) formula Units: m

L= 0.0158 x Screen diagonal (inch) – 0.0835

L= 0.0172 x Screen diagonal (inch) – 0.0835

ET-D75LE1

(1.5–2.0 :1)

Minimal distance: L=0.0307 x Screen diagonal (inch) – 0.0760 Maximal distance: L=0.0410 x Screen diagonal (inch) – 0.1004

4:3

16:9

Minimal distance: L=0.0334 x Screen diagonal (inch) – 0.0760 Maximal distance: L=0.0446 x Screen diagonal (inch) – 0.1004

ET-D75LE2

(2.0–3.0 :1)

4:3

Minimal distance: L=0.0412 x Screen diagonal (inch) – 0.0795 Maximal distance: L=0.0617 x Screen diagonal (inch) – 0.1064

16:9

Minimal distance: L=0.0617 x Screen diagonal (inch) – 0.0958 Maximal distance: L=0.1031 x Screen diagonal (inch) – 0.1216

Minimal distance: L=0.0448 x Screen diagonal (inch) – 0.0795 Maximal distance: L=0.0672 x Screen diagonal (inch) – 0.1064

4:3

ET-D75LE3

(3.0–5.0 :1)

16:9

Minimal distance: L=0.0672 x Screen diagonal (inch) – 0.0958 Maximal distance: L=0.1123 x Screen diagonal (inch) – 0.1216

Minimal distance: L=0.1031 x Screen diagonal (inch) – 0.1158 Maximal distance: L=0.1639 x Screen diagonal (inch) – 0.1013

4:3

ET-D75LE4

(5.0–8.0 :1)

16:9

Minimal distance: L=0.1786 x Screen diagonal (inch) – 0.3862 Maximal distance: L=0.3346 x Screen diagonal (inch) – 0.3598

Minimal distance: L=0.1640 x Screen diagonal (inch) – 0.3862 Maximal distance: L=0.3072 x Screen diagonal (inch) – 0.3598

4:3

ET-D75LE8

(8.0–15.0 :1)

16:9

4:3

Zoom

lens

Fixed-

focus

lens

Calculation formulas for projection distance by lens types (for PT-DW7000E)

ET-D75LE5

(0.8:1)

Model number of projection lens

Aspect ratio

Projection distance (L) formula Units: m

L= 0.0176 x Screen diagonal (inch) – 0.0835

ET-D75LE1

(1.5–2.0 :1)

Minimal distance: L=0.0343 x Screen diagonal (inch) – 0.0760 Maximal distance: L=0.0458 x Screen diagonal (inch) – 0.1004

16:9

ET-D75LE2

(2.0–3.0 :1)

16:9

Minimal distance: L=0.0460 x Screen diagonal (inch) – 0.0795 Maximal distance: L=0.0689 x Screen diagonal (inch) – 0.1064

Minimal distance: L=0.0689 x Screen diagonal (inch) – 0.0958 Maximal distance: L=0.1151 x Screen diagonal (inch) – 0.1216

16:9

ET-D75LE3

(3.0–5.0 :1)

Minimal distance: L=0.1151 x Screen diagonal (inch) – 0.1158 Maximal distance: L=0.1831 x Screen diagonal (inch) – 0.1013

16:9

ET-D75LE4

(5.0–8.0 :1)

Minimal distance: L=0.1831 x Screen diagonal (inch) – 0.3862 Maximal distance: L=0.3430 x Screen diagonal (inch) – 0.3598

16:9

ET-D75LE8

(8.0–15.0 :1)

16:9

Zoom

lens

Fixed-

focus

lens

Connection

Before connection, read carefully the instruction manual for the device to be connected. Turning off the power switch of the devices before connecting cables. If any connection cable is not supplied with the device, or if no optional cable is available for connection of the

device, prepare a necessary system connection cable to suit the device. Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture. In

this case, a time base corrector (TBC) must be connected. The projector accepts the following signals: video, S-Video, analogue RGB and digital signals from the PC. Some PC models cannot be connected to the projector.

The pin-out and signal names of the S-VIDEO IN terminal are shown in the diagram below.

The pin-out and signal names of the RGB2 input terminal are shown in the diagram below.

Outside view

Pin No.

Ground (colour signal

)

Luminance signal Colour signal

Signal

Ground (luminance signal)

Outside view

Signal

R/P

G/G · SYNC/Y B/P

SDA HD/SYNC VD SCL

Pin No.

Before starting connection

and are not assigned.

~ , and are GND terminals.

and are effective if the PC has the corresponding

functions.

ENGLISH

SERIAL

S-VIDEO

VIDEO

REMOTE 1

RGB 1 IN

OUT

SYNC/HD VDB/PBG/Y

REMOTE 2

R/PR

RS-232C (G) / RS-422 (R)RS-232C (G) / RS-422 (R)

RGB 2 IN

Video deck (TBC built-in)

High-vision video deck

Control PC

Colour monitor

Red (connected to PR terminal) Blue (connected to P

B terminal)

Green (connected to Y terminal)

Video deck (TBC built-in)

Example of connecting with VIDEO devices

• When connecting with a video deck, be sure to use the one with a built-in time base corrector (TBC) or use a TBC between the projector and the video deck.

• If nonstandard burst signals are connected, the image may be distorted. If this is the case, connect a TBC between the projector and the video deck.

Attention

SERIAL

S-VIDEO

VIDEO

REMOTE 1

RGB 1 IN

OUT

SYNC/HD VDB/PBG/Y

REMOTE 2

R/PR

RS-232C (G) / RS-422 (R)RS-232C (G) / RS-422 (R)

SERIAL

S-VIDEO

VIDEO

REMOTE 1

RGB 1 IN

OUT

SYNC/HD VDB/PBG/Y

REMOTE 2

R/PR

RS-232C (G) / RS-422 (R)RS-232C (G) / RS-422 (R)

RGB 2 IN

I/F

PC PC

Control PC

• When the main power of the main unit is turned off, also turn off the power of the PC.

Note

Attention

• For the specifications of the RGB signals that can be applied from the PC, see the data sheet on page 104.

• If your PC has the resume feature (last memory), the computer may not function properly until the resume capability is disabled.

Example of connecting with personal computers

Connection

ENGLISH

SERIAL

S-VIDEO

VIDEO

REMOTE 1

RGB 1 IN

OUT

SYNC/HD VDB/PBG/Y

REMOTE 2

R/PR

RS-232C (G) / RS-422 (R)RS-232C (G) / RS-422 (R)

SERIAL

S-VIDEO

VIDEO

REMOTE 1

RGB 1 IN

OUT

SYNC/HD VDB/PBG/Y

REMOTE 2

R/PR

RS-232C (G) / RS-422 (R)RS-232C (G) / RS-422 (R)

RGB 2 IN

OUT

O F

O W

O N

N P

U T

E L E

C T

V P

N /

F F

S i

n a l S

e l

e c

o r

T W

S W

Digital broadcasting

tuner

DVD player

Signal selector

Video deck

(TBC built-in)

Notebook computer

Control PC

Note

• When multiple signals of the same type are switched and input to RGB1 IN (for example, when switching multiple high-vision signals for usage), use a dedicated signal selector. When the signal selector is connected to the projector with a RS-232C cable, signals can be used separately according to the input terminal on the signal selector.

• Carefully read also the instruction manual for the signal selector.

Example of connecting with the signal selector

SMPTE259M compliant : 480i, 576i

10BASE-T/100BASE-TX

SMPTE259M compliant : 480i, 576i SMPTE292M compliant :

720/60p, 720/59.94p, 720/50p 1 035/60i, 1 035/59.94i, 1 080/60i, 1 080/59.94i 1 080/50i, 1 080/24sF, 1 080/23.98sF, 1 080/30p 1 080/29.97p, 1 080/25p, 1 080/24p, 1 080/23.98p

10BASE-T/100BASE-TX

HDCP-compliant *1 DVI-D single link, DVI 1.0 compliant EDID1 :

480p, 576p, 720/60p, 720/59.94p, 720/50p

1 080/60i, 1 080/59.94i, 1 080/50i, 1 080/24sF,

1 080/23.98sF

1 080/30p, 1 080/29.97p, 1 080/25p, 1 080/24p,

1 080/23.98p

EDID2 :

Displayable resolution VGA - UXGA (non-interlace) Dot clock frequency 25 - 162MHz

10BASE-T/100BASE-TX

Module

Module model

No.

Terminal Signal formats supported

SD-SDI input module

ET-MD77SD1

BNC input x 1 BNC output x 1

HD/SD-SDI input module

ET-MD77SD3

BNC input x 1 BNC output x 1

DVI-D input module

ET-MD77DV

DVI-D 24p input x 1

RJ-45 input x 1

Network module

ET-MD77NT RJ-45 input x 1

*1...HDCP (High-bandwidth Digital Content Protection)

HDCP is a specification for encoding digital image signals which was developed to protect digital content. The DVI/HDMI output signals from the HDCP-compliant equipment have been encoded by the HDCP specifications to ensure content protection, but the DVI input module is capable of displaying the digital images properly since it complies with the HDCP specification.

Installation of input module (optional)

Installing the input module

Types of the input modules (optional)

Prepare beforehand an input module (optional) compatible with the input signals of the system.

ENGLISH

Procedure of installation

Disconnect the power before installing the input module.

Slot cover

Remove 2 screws.

Input module

Slot

Tighten the two screws.

Remove the slot cover.

Insert the input module.

Fix the input module.

This projector needs to register the type of input signal after the installation of the input module. (For details on the registration of the input signals, refer to pages 38–41.)

SD-SDI input

module ET-MD77SD1

DVI-D input module

ET-MD77DV

Network module

ET-MD77NT

SDI signal

DVI

signal

LAN 10BASE-T/ 100BASE-TX

Projector

High-vision

video deck

DVD player

Business

digital VCR

HD/SD-SDI input

module ET-MD77SD3

Connecting signals to the input module

When installing the projector, it is necessary to connect signals to the input module in accordance with the connecting equipment. Refer to the following diagram to establish proper signal connection.

Installation of input module (optional)

ENGLISH

SD-SDI Module ET-MD77SD1

SERIAL

OUT

LAN

SD-SDI signal

SD-SDI signal output

(active through)

LAN terminal

(10BASE-T / 100BASE-TX)

Business

digital VCR

For details on the network function, refer to page 82.

SD-SDI input module (optional) ET-MD77SD1 (for 480i/576i)

• Insert the input module suitable for the input signal specifications.

• Normally, use SYSTEM SELECTOR in “AUTO”.

Automatic detection may malfunction if any unstable signal is connected. If this happens, switch to a system that is compatible with the signal format using the SYSTEM SELECTOR button.

• Use the SYSTEM SELECTOR button to toggle the systems of the input module that supports two types of signal specifications. Upon toggling, the input signals are displayed on the screen and cleared automatically.

AUTO 480i

576i

Connecting the signal to the SD-SDI input module

Installation of input module (optional)

• Insert the input module that meets the input signal specifications.

• Normally, use SYSTEM SELECTOR in “AUTO”.

• Any of the format systems can be selected using the SYSTEM SELECTOR button which supports 9 types

(15 formats) of HD signal standards (SMPTE292M) and 2 types of SD signal standards (SMPTE259M) shown below by toggling between any one of the formats. During the selection process, the input signals and other information appear on-screen and are cleared automatically.

• Automatic detection may malfunction if any unstable signal is connected. If this happens, switch to a system that is compatible with the signal format using the SYSTEM SELECTOR button.

• Use a 5CFB or superior cable for connection to transmit the image information without error. (Example: 5CFB, 5CFTX, 7CFB etc.)

Connecting the signal to the HD/SD-SDI input module

HD/SD-SDI input module (optional) ET-MD77SD3 (for HD/SD)

HD/SD-SDI Module ET-MD77SD3

SERIAL

OUT

LAN

HD-SDI or

SD-SDI signal

HD-SDI or SD-SDI

signal output

(active through)

LAN terminal

(10BASE-T / 100BASE-TX)

For details on the network function, refer to page 82.

Business

digital VCR

AUTO

1 080/60i 1 035/60i 720/60p 1 080/24p 1 080/50i

576i 480i 720/50p 1 080/24sF 1 080/25p 1 080/30p

+ 76 hidden pages