Panasonic PT-DW640E, PT-DW640EL, PT-DX610E, PT-DX610EL Operating Instruction

Operating Instructions
Functional Manual
DLPTM Projector
Model No.
PT-DW640E
Commercial Use
PT-DW640EL  PT-DX610E  PT-DX610EL
Thank you for purchasing this Panasonic product.
This manual is common to all the models regardless of sufxes of the Model No.
zS: Silver model, the standard zoom lens supplied LS: Silver model, the lens sold separately
K: Black model, the standard zoom lens supplied LK: Black model, the lens sold separately
■ Before operating this product, please read the instructions carefully and save this manual for future use.
Before using your projector, be sure to read “Read this rst!” (x pages 2 to 8).
ENGLISH
TQBJ0507
Read this rst!
Read this rst!
WARNING: THIS APPARATUS MUST BE EARTHED.
WARNING: To prevent damage which may result in re or shock hazard, do not expose this appliance to rain
or moisture.
This device is not intended for use in the direct eld of view at visual display workplaces. To avoid incommoding reexions at visual display workplaces this device must not be placed in the direct eld of view.
The equipment is not intended for used at a video workstation in compliance BildscharbV.
The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779.
WARNING:
1. Remove the plug from the mains socket when this unit is not in use for a prolonged period of time.
2. To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualied
service personnel.
3. Do not remove the earthing pin on the mains plug. This apparatus is equipped with a three prong earthingtype mains plug. This plug will only t an earthing-type mains socket. This is a safety feature. If you are unable to insert the plug into the mains socket, contact an electrician. Do not defeat the purpose of the
earthing plug.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
CAUTION: To assure continued compliance, follow the attached installation instructions, which include
using the provided power cord and shielded interface cables when connecting to computer or
peripheral device. If you use serial port to connect PC for external control of projector, you must use a commercial RS-232C serial interface cable with ferrite core. Any unauthorized changes or modications to this equipment will void the user’s authority to operate.
Product information (for Turkey only)
EEE Yönetmeliğine Uygundur. EEE Complies with Directive of Turkey.
Importer’s name and address within the European Union
Panasonic Marketing Europe GmbH
Panasonic Testing Center
Winsbergring 15, 22525 Hamburg, Germany
2 - ENGLISH
Be sure to read “Read this rst!”
Read this rst!
IMPORTANT: THE MOULDED PLUG (U.K. only)
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is tted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark
or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is retted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from an Authorised Service Center.
If the tted moulded plug is unsuitable for the mains socket in your home, then the fuse should be removed and the plug cut off and disposed of safely.
There is a danger of severe electrical shock if the
cut off plug is inserted into any 13 amp socket.
If a new plug is to be tted, please observe the wiring code as shown below. If in any doubt, please consult a qualied electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green - and - Yellow: Earth Blue: Neutral Brown: Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings
dentifying the terminals in your plug, proceed as follows.
i
The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol
or coloured GREEN or GREEN -
AND - YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
BS1363/A
N
13A250V
HE-8
L
ASA
ENGLISH - 3
Read this rst!
WARNING:
POWER
The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible when problems occur. If the following problems occur, cut off the power supply immediately.
Continued use of the projector in these conditions will result in re or electric shock.
zIf foreign objects or water get inside the projector, cut off the power supply. zIf the projector is dropped or the cabinet is broken, cut off the power supply. zIf you notice smoke, strange smells or noise coming from the projector, cut off the power supply.
Please contact an Authorized Service Center for repairs, and do not attempt to repair the projector yourself.
During a thunderstorm, do not touch the projector or the cable.
Electric shocks can result.
Do not do anything that might damage the power cord or the power plug.
If the power cord is used while damaged, electric shocks, short-circuits or re will result.
zDo not damage the power cord, make any modications to it, place it near any hot objects, bend it
excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.
Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary.
Completely insert the power plug into the wall outlet and the power connector into the projector terminal.
If the plug is not inserted correctly, electric shocks or overheating will result.
zDo not use plugs which are damaged or wall outlets which are coming loose from the wall.
Do not use anything other than the provided power cord.
Failure to observe this will result in re or electric shocks. Please note that if you do not use the provided power
cord to ground the device on the side of the outlet, this may result in electric shocks.
Clean the power plug regularly to prevent it from becoming covered in dust.
Failure to observe this will cause a re.
zIf dust builds up on the power plug, the resulting humidity can damage the insulation.
Pull the power plug out from the wall outlet and wipe it with a dry cloth regularly.
Do not handle the power plug and power connector with wet hands.
Failure to observe this will result in electric shocks.
Do not overload the wall outlet.
If the power supply is overloaded (ex., by using too many adapters), overheating may occur and re will result.
ON USE/INSTALLATION
Do not place the projector on soft materials such as carpets or sponge mats.
Doing so will cause the projector to overheat, which can cause burns, re or damage to the projector.
Do not set up the projector in humid or dusty places or in places where the projector may come into contact with oily smoke or steam, ex. a bathroom.
Using the projector under such conditions will result in re, electric shocks or deterioration of components. Deterioration of components (such as ceiling mount brackets) may cause the projector which is mounted on the
ceiling to fall down.
Do not install this projector in a place which is not strong enough to take the full weight of the projector or on top of a surface which is sloped or unstable.
Failure to observe this will cause projector to fall down or tip over the projector, and severe injury or damage could result.
4 - ENGLISH
Read this rst!
WARNING:
Do not cover the air intake/exhaust ports or place anything within 500 mm (20") of them.
Doing so will cause the projector to overheat, which can cause re or damage to the projector.
zDo not place the projector in narrow, badly ventilated places. zDo not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.
Do not place your hands or other objects close to the air exhaust port.
Doing so will cause burns or damage your hands or other objects.
zHeated air comes out of the air exhaust port. Do not place your hands or face, or objects which cannot
withstand heat close to this port.
Do not look at or place your skin into the light emitted from the lens while the projector is being used.
Doing so can cause burns or loss of sight.
zStrong light is emitted from the projector’s lens. Do not look at or place your hands directly into this light. zBe especially careful not to let young children look into the lens. In addition, turn off the power and
disconnect the power plug when you are away from the projector.
Never attempt to remodel or disassemble the projector.
High voltages can cause re or electric shocks.
zFor any inspection, adjustment and repair work, please contact an Authorized Service Center.
Do not project an image with the lens cover attached.
Doing so can cause re.
Do not allow metal objects, ammable objects, or liquids to enter inside of the projector. Do not allow
the projector to get wet.
Doing so may cause short circuits or overheating, and result in re, electric shock, or malfunction of the
projector.
zDo not place containers of liquid or metal objects near the projector. zIf liquid enters inside of the projector, consult your dealer. zParticular attention must be paid to children.
Use the ceiling mount bracket specied by Panasonic.
Using the ceiling mount bracket other than the specied one will result in falling accidents.
zAttach the supplied safety cable to the ceiling mount bracket to prevent the projector from falling down.
Installation work (such as ceiling mount bracket) should only be carried out by a qualied technician.
If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks.
zDo not use anything other than an authorized ceiling mount bracket. zBe sure to use the provided accessory wire with an eye bolt as an extra safety measure to prevent the
projector from falling down. (Install in a different location to the ceiling mount bracket.)
ENGLISH - 5
Read this rst!
WARNING:
ACCESSORIES
Do not use or handle the batteries improperly, and refer to the following.
Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re.
zUse AA/R6 batteries. zDo not use unspecied batteries. zDo not use chargeable batteries. zDo not disassemble dry cell batteries. zDo not heat the batteries or place them into water or re. zDo not allow the + and – terminals of the batteries to come into contact with metallic objects such as
necklaces or hairpins. zDo not store or carry batteries together with metallic objects. zStore the batteries in a plastic bag and keep them away from metallic objects. zMake sure the polarities (+ and –) are correct when inserting the batteries. zDo not use a new battery together with an old battery or mix different types of batteries. zDo not use batteries with the outer cover peeling away or removed.
If the battery uid leaks, do not touch it with bare hands, and take the following measures if necessary.
zBattery uid on your skin or clothing could result in skin inammation or injury.
Rinse with clean water and seek medical advice immediately. zBattery uid coming in contact with your eyes could result in loss of sight.
In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately.
Do not disassemble the lamp unit.
Doing so can cause electric shocks, burns, or injury.
Lamp replacement
The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will
result.
zThe lamp can easily explode if struck against hard objects or dropped. zBefore replacing the lamp, be sure to turn the power off and to disconnect the power plug from the wall
outlet.
Electric shocks or explosions can result if this is not done.
zWhen replacing the lamp, turn the power off and allow it to cool for at least one hour before handling it
otherwise it can cause burns.
Do not use the supplied power cord with devices other than this projector.
zUsing the supplied power cord with devices other than this projector may cause short circuits or
overheating, and result in electric shock or re.
Remove the depleted batteries from the remote control promptly.
zLeaving them in the unit may result in uid leakage, overheating, or explosion of the batteries.
CAUTION:
POWER
When disconnecting the power cord, be sure to hold the power plug and power connector.
If the power cord itself is pulled, the lead will become damaged, and re, short-circuits or serious electric
shocks will result.
When not using the projector for an extended period of time, disconnect the power plug from the wall outlet.
Failure to do so may result in re or electric shock.
Disconnect the power plug from the wall outlet before carrying out any cleaning and replacing the unit.
Failure to do so may result in electric shock.
6 - ENGLISH
Read this rst!
CAUTION:
ON USE/INSTALLATION
Do not place heavy objects on top of the projector.
Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or injury. The projector will be damaged or deformed.
Do not put your weight on this projector.
You could fall or the projector could break, and injury will result.
zBe especially careful not to let young children stand or sit on the projector.
Do not place the projector in extremely hot locations.
Doing so will cause the outer casing or internal components to deteriorate, or result in re.
zTake particular care in locations exposed to direct sunlight or near stoves.
Do not place your hands in the openings beside the optical lens, while shifting the lens.
Failure to observe this could cause injury.
Do not stand in front of the lens while the projector is being used.
Doing so can cause damage and burns to clothing.
zStrong light is emitted from the projector’s lens.
Do not place objects in front of the lens while the projector is being used.
Doing so can cause damage to the object and can cause the set to malfunction.
zStrong light is emitted from the projector’s lens.
Always disconnect all cables before moving the projector.
Moving the projector with cables still attached can damage the cables, which will cause re or electric shocks to
occur.
ACCESSORIES
Do not use the old lamp unit.
If used it could cause lamp explosion.
If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the broken pieces.
Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and
which contains nearly the same amount of mercury as uorescent lamps, and the broken pieces will cause
injury.
zIf you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical
advice immediately. zAsk your dealer about replacing the lamp unit and check the inside of the projector.
Do not attach the air lter unit while it is wet.
Doing so may result in electric shock or malfunctions.
zAfter you clean the air lter units, dry them thoroughly before reattaching them.
Do not touch the fan with your ngers or any other parts of your body when changing the lamp unit.
Doing so can cause injury.
Ask your dealer about cleaning inside the projector once a year.
Continuous use while dust is accumulated inside the projector may result in re.
zFor cleaning fee, ask your dealer.
When not using the projector for an extended period of time, remove the batteries from the remote control.
Failure to observe this will cause the batteries to leak, overheat, catch re or explode, which may result in re
or contamination of surrounding area.
ENGLISH - 7
To remove the battery
Remote Control Battery
Read this rst!
1. Press the guide and lift the cover.
(ii)
(i)
2. Remove the batteries.
8 - ENGLISH
Trademarks
rr
• Microsoft®, Windows®, Windows Vista®, and Internet Explorer® are the registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• Mac, Mac OS, Mac OSX, and Safari are the trademarks of Apple Inc. registered in the United States and
other countries.
PJLinkTM is a trademark or pending trademark in Japan, the United States, and other countries and regions.
• HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
• VGA and XGA are trademarks of International Business Machines Corporation.
• SVGA is a registered trademark of the Video Electronics Standards Association.
• RoomView, Crestron RoomView, Crestron Connected, and Fusion RV are trademarks of Crestron Electronics, Inc.
The font used in the on-screen displays is a Ricoh bitmap font, which is manufactured and sold by Ricoh Company, Ltd.
• Adobe Flash Player is either a trademark or registered trademark of Adobe Systems Incorporated in the United States and/or other countries.
• Other names, company names or product names used in these operating instructions are the trademarks or
registered trademarks of their respective holders.
Please note that the operating instructions do not include the ® and TM symbols.
Illustrations in these operating instructions
rr
• Note that illustrations of the projector and screens may differ from the ones you actually see.
Page references
rr
• In these instructions, references to pages are indicated as: ( page 00).
Term
rr
• In these instructions, the “Wireless/wired remote control unit” accessories are referred to as the “Remote control”.
ENGLISH - 9
Features of the Projector
High luminance & High color reproducibility
▶The unique optical and lamp drive systems
achieve a high luminance and high color reproducibility while saving power.
Easy setup and improved serviceability
▶Extensive lineup of optional lenses allow
more exible setup of the projector.
Improved cost performance in maintenance fee
Quick Steps
For details, see the corresponding pages.
1. Set up the projector. (x page 26)
c
2. Attach the projection lens. (x page 35)
c
3. Connect with other devices. (x page 37)
c
4. Connect the power cord. (x page 41)
▶The long life lter reduces maintenance
costs.
c
5. Switch on the projector. (x page 42)
c
6. Make initial settings. (x page 19)
*
c
7. Select the input signal. (x page 45)
c
8. Adjust the image. (x page 45)
10 - ENGLISH
* These are the steps to be taken when you switch on the power for the
rst time after purchasing the projector.
Contents
Contents
Read this rst! ............................................2
Chapter 1 Preparation
Precautions for use ................................................. 14
Cautions when transporting .................................. 14
Cautions when installing ....................................... 14
Security ................................................................ 15
Disposal ................................................................ 16
Cautions on use ................................................... 16
Software information regarding this product ......... 16
Accessories .......................................................... 17
Optional accessories ............................................ 18
Start-up display ....................................................... 19
Initial setting (display language) ........................... 19
Initial setting (projector setup) .............................. 19
About your projector ............................................... 20
Remote control ..................................................... 20
Projector body ...................................................... 21
Using the remote control ........................................ 23
Inserting and removing the batteries .................... 23
Setting Remote control ID numbers ..................... 23
Connecting to the projector with a cable .............. 24
Chapter 2 Getting Started
Setting up ................................................................. 26
Projection method ................................................ 26
Parts for ceiling mount (optional) .......................... 26
Screen size and throw distance ........................... 27
Adjusting adjustable feet ...................................... 34
Removing/attaching the projection lens ............... 35
Removing the projection lens ............................... 35
Attaching the projection lens ................................ 35
Connections ............................................................. 37
Before connecting to the projector ....................... 37
Connecting example: AV equipment .................... 38
Connecting example: Computers ......................... 38
Chapter 3 Basic Operation
Switching on/off the projector ................................ 41
Connecting the power cord .................................. 41
Power indicator ..................................................... 42
Switching on the projector .................................... 42
Making adjustments and selections ..................... 43
Switching off the projector .................................... 43
Direct power off function ....................................... 44
Be sure to read “Read this rst!”. (x pages 2 to 8)
Projecting ................................................................. 45
Selecting the input signal ..................................... 45
Adjusting the focus, zoom, and shift ..................... 45
Moving the lens to the home position ................... 46
Adjustment range by the lens position shift
(optical shift) ...................................................... 46
Remote control operation ....................................... 47
Using the shutter function ..................................... 47
Using the on-screen display function ................... 47
Switching the input ............................................... 48
Using the status function ...................................... 48
Using the automatic setup function ...................... 48
Using the function button ...................................... 49
Displaying the internal test pattern ....................... 49
Changing the picture aspect ratio ......................... 49
Chapter 4 Settings
Menu navigation ...................................................... 51
Navigating through the menu ............................... 51
Main menu ............................................................ 52
Sub-menu ............................................................. 52
[PICTURE] menu ...................................................... 55
[PICTURE MODE] ................................................ 55
[CONTRAST] ........................................................ 55
[BRIGHTNESS] .................................................... 55
[COLOR] ............................................................... 56
[TINT] ................................................................... 56
[COLOR TEMPERATURE] ................................... 56
[WHITE GAIN] ...................................................... 57
[SYSTEM DAYLIGHT VIEW] ................................ 57
[SHARPNESS] ..................................................... 58
[NOISE REDUCTION] .......................................... 58
[AI] ........................................................................ 58
[SYSTEM SELECTOR] ........................................ 59
[POSITION] menu .................................................... 60
[SHIFT] ................................................................. 60
[ASPECT] ............................................................. 60
[ZOOM] ................................................................. 61
[CLOCK PHASE] .................................................. 62
[KEYSTONE] ........................................................ 63
[ADVANCED MENU] menu ...................................... 64
[DIGITAL CINEMA REALITY] ............................... 64
[BLANKING] ......................................................... 64
[INPUT RESOLUTION] ........................................ 65
[CLAMP POSITION] ............................................. 65
[EDGE BLENDING] .............................................. 65
[RASTER POSITION] ........................................... 66
ENGLISH - 11
Contents
[DISPLAY LANGUAGE] menu ................................. 67
Changing the display language ............................ 67
[DISPLAY OPTION] menu ........................................ 68
[COLOR MATCHING] ........................................... 68
[COLOR CORRECTION] ..................................... 69
[CONTRAST MODE] ............................................ 69
[SCREEN SETTING] ............................................ 69
[AUTO SIGNAL] ................................................... 70
[AUTO SETUP]..................................................... 70
[RGB IN] ............................................................... 70
[DVI-D IN] ............................................................. 70
[HDMI IN] .............................................................. 71
[ON-SCREEN DISPLAY] ...................................... 71
[BACK COLOR] .................................................... 72
[STARTUP LOGO] ................................................ 72
[SHUTTER SETTING] .......................................... 73
[FREEZE] ............................................................. 73
[SIDE BY SIDE] (PT-DW640E only) ..................... 73
[CUT OFF] ............................................................ 74
[PROJECTOR SETUP] menu .................................. 75
[PROJECTOR ID] ................................................. 75
[PROJECTION METHOD] .................................... 75
[COOLING CONDITION] ...................................... 76
[HIGH ALTITUDE MODE] ..................................... 76
[LAMP SELECT] ................................................... 76
[LAMP RELAY] ..................................................... 77
[LAMP POWER] ................................................... 77
[STANDBY MODE] ............................................... 78
[SCHEDULE] ........................................................ 78
[STARTUP INPUT SELECT] ................................ 79
[RS-232C] ............................................................. 80
[REMOTE2 MODE] .............................................. 81
[STATUS] .............................................................. 81
[NO SIGNAL SHUT-OFF] ..................................... 82
[FUNCTION BUTTON] ......................................... 82
[DATE AND TIME] ................................................ 83
[SAVE ALL USER DATA] ...................................... 83
[LOAD ALL USER DATA] ..................................... 84
[INITIALIZE] .......................................................... 84
[SERVICE PASSWORD] ...................................... 84
[TEST PATTERN] menu ........................................... 85
[TEST PATTERN] ................................................. 85
[SIGNAL LIST] menu ............................................... 86
Registering a signal to the list .............................. 86
Renaming the registered data .............................. 86
Deleting the registered data ................................. 86
Protecting the registered data .............................. 87
Expanding signal lock-in range ............................ 87
Managing the sub memory list ............................. 87
[SECURITY] menu ................................................... 89
[SECURITY PASSWORD] .................................... 89
[SECURITY PASSWORD CHANGE] ................... 89
[DISPLAY SETTING] ............................................ 89
[TEXT CHANGE] .................................................. 90
[MENU LOCK] ...................................................... 90
[MENU LOCK PASSWORD] ................................ 90
[CONTROL DEVICE SETUP] ............................... 90
[NETWORK] menu ................................................... 92
[NETWORK SETUP] ............................................ 92
[NETWORK CONTROL] ...................................... 92
[NETWORK STATUS] .......................................... 93
Network connections ............................................ 93
Accessing from the Web browser ......................... 94
Chapter 5 Maintenance
Lamp/Temperature/Filter indicators .................... 110
Managing the indicated problems .......................110
Maintenance/replacement..................................... 112
Before maintaining/replacing the unit ..................112
Maintenance ........................................................112
Replacing the unit ................................................113
Troubleshooting .................................................... 116
Chapter 6 Appendix
Technical information ........................................... 11 8
PJLink protocol ....................................................118
Control commands via LAN .................................119
<SERIAL IN>/<SERIAL OUT> terminal .............. 121
<REMOTE 2 IN> terminal .................................. 124
Two window display combination list (PT-
DW640E only) ................................................. 125
Menu lock password ........................................... 125
List of compatible signals ................................... 125
Specications ........................................................ 127
Dimensions ............................................................ 129
Ceiling mount bracket safeguards....................... 130
Index ....................................................................... 131
12 - ENGLISH
Chapter 1
This chapter describes things you need to know or check before using the projector.
Preparation
ENGLISH - 13
Chapter 1 Preparation — Precautions for use

Precautions for use

Cautions when transporting

The projection lens is susceptible to effects from vibration or impact. Make sure to remove the projection lens when transporting.
rf
Also, use a protection cover or the like to prevent dust from affecting the projection lens or the set. When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. They may damage the internal
rf
parts and result in malfunctions.
Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.
rf

Cautions when installing

Always attach the projection lens cover after attaching the projection lens.
rr
If the cover is not attached, dust will accumulate inside and may cause malfunctions.
Do not set up the projector outdoors.
rr
The projector is designed for indoor use only.
Do not set up the projector in the following locations.
rr
Places where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal parts or malfunction.
rf
Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may uctuate in rare cases due to the hot air from
rf
the air exhaust port or the heated or cooled air. Make sure that the exhaust from the projector or other equipment, or the air from the air
conditioner does not blow toward the front of the projector.
Near lights (studio lamps, etc.) and other locations of great temperature uctuation (“Operating environment” (x page 128)): Doing so may
rf
shorten the life of the lamp or result in deformation of the outer case and malfunctions.
Near high-voltage power lines or near motors: Doing so may interfere with the operation of the projector.
rf
Place where there is high-power laser equipment: Directing a laser beam onto the lens surface causes damage to the DLP chips.
rf
Be sure to ask a specialized technician or your dealer when installing the product to a ceiling.
rr
If the product is to be installed hanging from the ceiling, purchase an optional Ceiling Mount Attachment. Model No.: ET-PKD56H (for high ceilings), ET-PKD55S (for low ceilings)
Lens focus
rr
The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in the period just after switching on the power. Wait at least 30 minutes with the image projected before adjusting the lens focus.
Make sure to set [HIGH ALTITUDE MODE] to [ON] when using the projector at elevations of
rr
1 400 m (4 593 ft) or higher and lower than 2 700 m (8 858 ft) above sea level.
Doing so may shorten the life of the internal parts and result in malfunctions.
Make sure to set [HIGH ALTITUDE MODE] to [OFF] when using the projector at elevations
rr
lower than 1 400 m (4 593 ft) above sea level.
Doing so may shorten the life of the internal parts and result in malfunctions.
Do not install the projector at elevations of 2 700 m (8 858 ft) or higher above sea level.
rr
Doing so may shorten the life of the internal parts and result in malfunctions.
Do not use the projector tilted to the right or left
rr
Using the projector at a vertical angle that exceeds 15° may reduce product life or result in malfunction.
When installing and using the projector at an angle that exceeds 30° vertically, set [COOLING
rr
CONDITION] (x page 76).
Failure to observe this will result in malfunctions or shorten the life of the lamp or other components.
Cautions when setting up the projector
rr
To install and use the projector via a method that does not use the adjustable feet in a oor standing installation, x the projector using the
rf
ve screw holes for ceiling mounting (Fig. 1). (Screw diameter: M6, tapping depth inside the set: 12 mm (15/32"), torque: 4 ± 0.5 N·m)
14 - ENGLISH
Chapter 1 Preparation — Precautions for use
6FUHZKROHVIRUFHLOLQJPRXQW0
PPRUORQJHU PPRUORQJHU PPRUORQJHU
Use the adjustable feet only for the oor standing installation and for adjusting the angle. Using it for other purposes may damage the set.
rf
$GMXVWDEOHIHHW
)LJ7KHSRVLWLRQVRIVFUHZKROHVIRUFHLOLQJPRXQWDQGDGMXVWDEOHIHHW
Do not stack projectors on top of each other.
rf
Do not hold the projector by the top surface.
rf
Do not use the projector tilted at an angle that exceeds ± 15° from the horizontal plane.
rf
Do not block the ventilation ports (intake and exhaust) of the projector.
rf
Prevent hot and cool air from the air conditioning system from blowing directly to the ventilation ports (intake and exhaust) of the projector.
rf
PPRUORQJHU
Do not install the projector in a conned space.
rf
When it is necessary to install the projector in a conned space, install the air conditioning or ventilation separately. Exhaust heat may
accumulate when the ventilation is not enough, triggering the protection circuit of the projector.
Make a clearance of at least 20 mm (0.8") between the projector bottom and setting surface by inserting spacers (metallic) etc. between
rf
them.

Security

When using this product, take safety measures against the following incidents.
Personal information being leaked via this product
rf
Unauthorized operation of this product by a malicious third party
rf
Interfering or stopping of this product by a malicious third party
rf
Take sufcient security measures. (x pages 89, 104)
Make your password difcult to guess as much as possible.
rf
Change your password periodically.
rf
Panasonic Corporation or its afliate companies will never ask for your password directly. Do not divulge your password in case you receive
rf
such inquiries.
The connecting network must be secured by a rewall, etc.
rf
Set a password for the web control and restrict the users who can log in.
rf
ENGLISH - 15
Chapter 1 Preparation — Precautions for use

Disposal

To dispose of the product, ask your local authorities or dealer for correct methods of disposal. The lamp contains mercury. When disposing of used lamp units, contact your local authorities or dealer for correct methods of disposal.

Cautions on use

To get a good picture quality
rr
In order to view a beautiful image in higher contrast, prepare an appropriate environment. Draw curtains or blinds over windows and turn off
any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen.
Do not touch the surface of the projection lens with your bare hands.
rr
If the surface of the projection lens becomes dirty from ngerprints or anything else, this will be magnied and projected onto the screen. Please put the lens cover (accessory) on the projector when you do not use it.
DLP chips
rr
The DLP chips are precision-made. Note that in rare cases, pixels of high precision could be missing or always lit. Note that such
rf
phenomena does not indicate malfunction. This is not a malfunction.
Directing a high-power laser beam onto the lens surface can damage the DLP chips.
rf
Do not move the projector while it is operating or subject it to vibration or impact.
rr
Doing so may shorten the service life of its internal components.
Lamp
rr
The luminous source of the projector is a high-pressure mercury lamp.
A high-pressure mercury lamp has the following characteristics.
The luminance of the lamp will decrease by duration of usage.
rf
The lamp may burst with a loud sound or have its service life shortened because of shock, chipping, or degradation due to cumulative
rf
operating time.
The lamp life varies greatly depending on individual differences and usage conditions. In particular, frequently switching the power on/off
rf
accelerates lamp deterioration and greatly affects lamp life.
Continuous use for one week or longer accelerates lamp deterioration. Lamp relay function (x page 77) can be used to reduce
rf
deterioration caused by continuous use.
In rare cases, the lamps burst shortly after projection starts.
rf
The risk of bursting increases when the lamp is used beyond its replacement cycle. Make sure to replace the lamp unit regularly.
rf
(“When to replace the lamp unit” (x page 114), “Replacing the lamp unit” (x page 114)) If the lamp bursts, gas contained inside of the lamp is released in a form of smoke.
rf
It is recommended that you store replacement lamp units for contingency.
rf
About connections to computer or peripheral device
rr
To assure continued compliance, follow the attached installation instructions, which include using the provided power cord and shielded
rf
interface cables when connecting to computer or peripheral device.
Use a commercial DVI-D cable with a ferrite core.
rf

Software information regarding this product

© Panasonic Corporation 2012
This product incorporates the following software.
(1) The software which is developed independently by or for Panasonic Corporation (2)The software which is licensed under the GNU GENERAL PUBLIC LICENSE (3)The software which is licensed under the GNU LESSER GENERAL PUBLIC LICENSE For the license conditions of software categorized as (2) and (3), refer to the provisions of the Software license (GNU GENERAL PUBLIC LICENSE and GNU LESSER GENERAL PUBLIC LICENSE) in the supplied CD-ROM. (Those provisions are written in the original (English)
because they have been stipulated by third parties.)
If you have any questions regarding the software, contact (sav.pj.gpl.pavc@ml.jp.panasonic.com) by E-mail.
16 - ENGLISH
Chapter 1 Preparation — Precautions for use

Accessories

Make sure that the following accessories are provided with your projector. Numbers enclosed in < > show the number of accessories.
Wireless/wired remote control unit <1>
(N2QAYB000784)
Power cord <1>
(K2CM3FZ00003)
Power cord <1>
(K2CT3FZ00003)
Lens cover <1>
(TKKL5244)
(for models with attached lenses only)
CD-ROM <1>
(TXFQB02VLH4)
Power cord secure lock <1>
(TTRA0183)
AA/R6 battery <2>
Projection lens cover <1>
(TKPB35101)
Attention
After unpacking the projector, discard the power cord cap and packaging material properly.
rf
For missing accessories, consult your dealer.
rf
Store small parts in an appropriate manner, and keep them away from small children.
rf
Note
The model numbers of accessories and optional components are subject to change without notice.
rf
Contents of the supplied CD-ROM
The contents of the supplied CD-ROM are as follows.
Instruction/list (PDF) Operating Instructions - Functional Manual
Multi Projector Monitoring & Control Software Operation Manual
Logo Transfer Software Operating Manual
List of Compatible Projector Models This is a list of projectors that are compatible with the
software contained in the CD-ROM and their restrictions.
Software license (GNU GENERAL PUBLIC LICENSE, GNU LESSER
GENERAL PUBLIC LICENSE)
Software Multi Projector Monitoring & Control Software
(Windows)
Logo Transfer Software (Windows) This software allows you to create original images, such
This software allows you to monitor and control multiple
projectors connected to the LAN.
as company logos to be displayed when projection starts, and transfer them to the projector.
(For remote control unit)
ENGLISH - 17
Chapter 1 Preparation — Precautions for use

Optional accessories

Optional accessories (product name) Model No.
ET-DLE055 (xed-focus lens), ET-DLE080 (ultra short-focus zoom lens), ET-DLE150 (short-
Projection lens
Ceiling mount bracket ET-PKD56H (for high ceilings), ET-PKD55S (for low ceilings)
Replacement lamp unit ET-LAD60A (1 pc), ET-LAD60AW (2 pcs)
Replacement lter unit ET-EMF300
focus zoom lens), ET-DLE250 (medium-focus zoom lens), ET-DLE350 (long-focus zoom lens), ET-DLE450 (ultra long-focus zoom lens)
18 - ENGLISH
Chapter 1 Preparation — Start-up display

Start-up display

The initial setting screen is displayed when the projector is switched on for the rst time after purchase as well as when [INITIALIZE] – [ALL USER DATA] (x page 84) is executed. Set them in accordance with circumstances.
In other occasions, you can change the settings by menu operations.
Note
When the projector is used for the rst time, you may be required to adjust the focus, zoom, and shift to display the menu screen clearly.
rf
Refer to “Adjusting the focus, zoom, and shift” (x page 45) for details.

Initial setting (display language)

Select the language to show on the screen. (x page 67)
Press as to select the display language.
1)
,1,7,$/6(77,1*
3/($6(6(/(&7/$1*8$*(
6(/(&7
(17(5
6(7

Initial setting (projector setup)

Set each item.
Press as to select an item.
1)
Press qw to switch the setting.
2)
,1,7,$/6(77,1*
352-(&7,210(7+2'
&22/,1*&21',7,21
6&5((1)250$7
6&5((1326,7,21
)5217)/225
)/2256(77,1*

Press the <ENTER> button to proceed to the
2)
initial setting.
Refer to the following pages for details.
rf
[PROJECTION METHOD] (x page 75) [COOLING CONDITION] (x page 76) [SCREEN FORMAT] (x page 69) [SCREEN POSITION] (x page 69) [HIGH ALTITUDE MODE] (x page 76)
Press the <ENTER> button.
3)
Conrm the setting value to complete the initial setting.
rf
+,*+$/7,78'(02'(
6:,7&+72+,*+$/7,78'(02'(21
,)29(5P)W
0(186(/(&7 &+$1*(
(17(5
6(7
2))
Note
If you press the <MENU> button in the initial setting (projector setup) screen, you can go back to the initial setting (display language)
rf
screen.
ENGLISH - 19
Chapter 1 Preparation — About your projector
)URQW 7RS

About your projector

Remote control

 



1 Remote control indicator
Flashes if any button in the remote control is pressed.
2 Power standby <v> button
Sets the projector to the standby mode when the <MAIN POWER> switch on the projector is set to <ON>.
3 Power on <b> button
Starts projection when the <MAIN POWER> switch on the projector is set to <ON> and the power is switched off (standby
mode).
4 Input selection (<RGB1>, <RGB2>, <DVI-D>, <VIDEO>,
<S-VIDEO>, <HDMI>) buttons
Switches the input signal to project. (x page 48)
5 <MENU> button/<ENTER> button/
Used to operate the menu screen. (x page 51)
6 <ON SCREEN> button
Switches the on-screen display function on (displayed)/off (hidden). (x page 47)
7 <TEST PATTERN> button
Displays the test pattern. (x page 49)
8 Number (<0> - <9>) buttons
Used when the system uses multiple projectors. Used to input ID numbers or passwords.
9 <STATUS> button
Displays the projector information.
Attention
asqw
 

 

buttons
%RWWRP

10 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image.
[PROGRESS] is displayed on the screen while the image is adjusted automatically. (x page 48)
11 <SHUTTER> button
Use to temporarily turn off the image. (x page 47)
12 <ASPECT> button
Switches the aspect ratio of the image. (x page 49)
13 Lens (<FOCUS>, <ZOOM>, <SHIFT>) buttons
Adjusts the projection lens. (x pages 43, 45)
14 <FUNCTION> button
You can assign a frequently used operation as a shortcut button.
(x page 49)
15 <DEFAULT> button
Resets the content of the sub-menu to the factory default.
(x page 51)
16 <ID SET> button
Sets the ID number of the remote control when a system uses multiple projectors. (x page 23)
17 <ID ALL> button
Use to simultaneously control all the projectors with one remote control when a system uses multiple projectors. (x page 23)
18 Remote control signal transmitter
19 Remote control wired terminal
Connecting to the projector with a cable (x page 24)
Do not drop the remote control.
rf
Avoid contact with liquids or moisture.
rf
Do not attempt to modify or disassemble the remote control.
rf
Note
The remote control can be used within a distance of about 30 m (98'5") if pointed directly at the remote control receiver. The remote control
rf
can control at angles of up to ±15° vertically and ±30° horizontally, but the effective control range may be reduced. If there are any obstacles between the remote control and the remote control signal receiver, the remote control may not operate properly.
rf
The signal will be reected off the screen. However, the operating range may be limited from light reection loss due to the screen material.
rf
If the remote control signal receiver directly receives strong light, such as uorescent light, the remote control may not operate properly.
rf
Use it in a place distant from the light source. The power indicator <ON (G)/STANDBY (R)> will ash if the projector receives a remote control signal.
rf
20 - ENGLISH

Projector body

)URQW 6LGH
%RWWRP
Chapter 1 Preparation — About your projector


5HDU


)URQW

Warning
  
)URQW
  
)URQW
 
8 Projection lens
(for models with attached lenses only)
9 Air exhaust port
10 Lamp unit cover (x page 114)
11 Control panel (x page 22)
12 Remote control signal receiver (rear)
13 Air intake port
14 Connecting terminals (x page 22)
15 <MAIN POWER> switch
Turns on/off the main power.
16 Security slot
This security slot is compatible with the Kensington security cables.
17 <AC IN> terminal
Connect the supplied power cord.
18 Air lter cover
The air lter unit is inside. (x page 112)
19 Burglar hook port
You can attach a commercial burglar prevention cable.
Keep your hands and other objects away from the air exhaust port.
Keep your hands and face away.
rf
Do not insert your ngers.
rf
Keep heat-sensitive objects away.
rf
Heated air from the air outlet port can cause bums, injury, or
deformations.
1 Power indicator <ON (G)/STANDBY (R)>
Displays the status of the power.
2 Lamp indicator <LAMP1>
Displays the status of lamp 1.
3 Lamp indicator <LAMP2>
Displays the status of lamp 2.
4 Temperature indicator <TEMP>
Displays the internal temperature status.
5 Filter indicator <FILTER>
Displays the status of the air lter unit.
6 Adjustable feet
Adjusts the projection angle.
7 Remote control signal receiver (front)
ENGLISH - 21
Control panel
rr
Chapter 1 Preparation — About your projector
1
2
3
4
5 6 7 8
1 Power standby <v> button
Sets the projector to the standby mode when the <MAIN POWER> switch on the projector is set to <ON>.
2 Power on <b> button
Starts projection when the <MAIN POWER> switch on the projector is set to <ON> when the power is switched off (standby
mode).
3 <VIDEO> button
Switches to VIDEO input.
4 <S-VIDEO> button
Switches to S-VIDEO input.
5 <RGB1> button
Switches to RGB1 input.
6 <RGB2> button
Switches to RGB2 input.
7 <DVI-D> button
Switches to DVI-D input.
8 <HDMI> button
Switches to HDMI input.
9
10
11
12
13
14
9 <MENU> button
Displays and erases the main menu.
Returns to the previous screen when a sub-menu is displayed.
(x page 51) If you press the <MENU> button on the control panel for at
least three seconds while the on-screen indication is off, the on­screen display is turned on.
10 <LENS> button
Adjusts the focus, zoom, and shift (position) of the lens.
11 <ENTER> button
Determines and executes an item in the menu screen.
12 <SHUTTER> button
Use to temporarily turn off the image. (x page 47)
13
asqw
Use to select items in the menu screen, change settings, and
adjust levels.
It is also used to enter [SECURITY] passwords.
14 <AUTO SETUP> button
Automatically adjusts the image display position while projecting
the image.
[PROGRESS] is displayed on the screen while the image is adjusted automatically. (x page 48)
selection buttons
Connecting terminals
rr
1 2 3 4 5 6
7 8 9 10 11
1 <LAN> terminal
This is a terminal to connect to the network.
Used for control and monitoring. Image input through network
connections is not possible.
2 <VIDEO IN> terminal
This is a terminal to input video signals.
3 <S-VIDEO IN> terminal
This is a terminal to input S video signals.
4 <RGB 1 IN> (<R/P
terminal
This is a terminal to input RGB signals or YCBCR/YPBPR signals.
5 <HDMI IN> terminal
This is a terminal to input HDMI signals.
6 <DVI-D IN> terminal
This is a terminal to input DVI-D signals.
>, <G/Y>, <B/PB>, <SYNC/HD>, <VD>)
R
Attention
7 <REMOTE 1 IN> terminal / <REMOTE 1 OUT> terminal
These are the terminals to connect the remote control for serial control when the system uses multiple projectors.
8 <REMOTE 2 IN> terminal
This is a terminal to remotely control the projector using the
external control circuit.
9 <SERIAL IN> terminal
This is a RS-232C compatible terminal to externally control the
projector by connecting a computer.
10 <SERIAL OUT> terminal
This is a terminal to output the signal connected to the <SERIAL IN> terminal.
11 <RGB 2 IN> terminal
This is a terminal to input RGB signals or YC
/YPBPR signals.
BCR
When a LAN cable is directly connected to the projector, the network connection must be made indoors.
rf
22 - ENGLISH
Chapter 1 Preparation — Using the remote control

Using the remote control

Inserting and removing the batteries

Open the cover.
1)
Insert the batteries and close the cover (insert
2)
the m side first).
(ii)
(i)
When removing the batteries, perform the steps in reverse
rf
order.

Setting Remote control ID numbers

When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector individually using single
remote control, if a unique ID number is assigned to each projector. After setting the ID number of the projector, set the same ID number on the remote control.
The factory default ID number of the projector is set to [ALL]. When using a single projector, press the <ID ALL> button on the remote control. Also, you can control a projector if you press the <ID ALL> button on the remote control even if you do not know the projector ID.
How to set
Press the <ID SET> button on the remote
1)
control.
Within five seconds, press the two-digit ID
2)
number set on the projector using the number (<0> - <9>) buttons.
If you press the <ID ALL> button, you can operate the projectors
rf
regardless of the setting of the projector’s ID number.
Attention
Since the ID number of the remote control can be set without the projector, do not press the <ID SET> button carelessly. If the <ID SET>
rf
button is pressed and no number (<0> - <9>) buttons are pressed within the next ve seconds, the ID number returns to its original value before the <ID SET> button was pressed. The ID number set on the remote control will be stored unless it is set again. However, it will be erased if the remote control is left with dead
rf
batteries. Set the same ID number again when the batteries are replaced.
Note
Set the ID number of the projector from the [PROJECTOR SETUP] menu → [PROJECTOR ID] (x page 75).
rf
ENGLISH - 23
Chapter 1 Preparation — Using the remote control

Connecting to the projector with a cable

When you use the system with multiple projectors, congure the units as in the following gure. Use a commercial M3 stereo mini jack cable and connect the other devices to the <REMOTE 1 IN>/<REMOTE 1 OUT> terminals of the projector.
The remote control is effective even in places where an obstacle stands in the light path or where devices are susceptible to outside light.
&RQQHFWLQJWHUPLQDOV
&RQQHFWLRQWRWKH VHFRQGSURMHFWRU
0VWHUHRPLQLMDFNFDEOH FRPPHUFLDOO\DYDLODEOH
5HPRWHFRQWURO
&RQQHFWWRUHPRWHFRQWURO ZLUHGWHUPLQDO
Attention
Use a cable that is 15 m (49'2") or shorter, with 2 core shield. The remote control may not operate when the length of the cable exceeds 15
rf
m (49'2") or when the shielding of the cable is inadequate.
24 - ENGLISH
Chapter 2
This chapter describes about things you need to do before using the projector such as the setup and connections.
Getting Started
ENGLISH - 25
Chapter 2 Getting Started — Setting up

Setting up

Projection method

You can use the projector with any of the following four projection methods. Select the appropriate method depending on the environment.
Mounting on the ceiling and projecting forward Setting on a desk/oor and projecting from rear
(Using the translucent screen)
Menu item
[PROJECTION METHOD] [FRONT/CEILING] [PROJECTION METHOD] [REAR/FLOOR]
[COOLING CONDITION] [CEILING SETTING] [COOLING CONDITION] [FLOOR SETTING]
Mounting on the ceiling and projecting from rear
(Using the translucent screen)
Menu item
[PROJECTION METHOD] [REAR/CEILING] [PROJECTION METHOD] [FRONT/FLOOR]
[COOLING CONDITION] [CEILING SETTING] [COOLING CONDITION] [FLOOR SETTING]
* For menu item details, refer to the [PROJECTOR SETUP] menu → [PROJECTION METHOD] (x page 75) and [COOLING CONDITION]
(x page 76).
*
*
Method Menu item
Setting on a desk/oor and projecting forward
Method Menu item
*
*
Method
Method

Parts for ceiling mount (optional)

You can install the projector on the ceiling using the optional ceiling mount bracket (ET-PKD56H: for high ceilings, or ET-PKD55S: for low
ceilings).
Use only the ceiling mount brackets specied for this projector.
rf
Refer to the installation manual for the ceiling mount bracket when installing the bracket and the projector.
rf
Attention
To ensure projector performance and security, installation of the ceiling mount bracket must be carried out by your dealer or a qualied
rf
technician.
26 - ENGLISH
Chapter 2 Getting Started — Setting up

Screen size and throw distance

Refer to the following gures and table describing projection distances to install the projector. Image size and image position can be adjusted
in accordance with the screen size and screen position.
3URMHFWLRQVFUHHQ
6'
6+
6:
L (LW/LT)
* LW: Minimum projection distance when the zoom lens is used
LT: Maximum projection distance when the zoom lens is used
*
SH Image height (m)
SW Image width (m)
H Distance (m) from the lens center to the bottom edge of the image
SD Image diagonal size (m)
Projection distance (m)
Attention
6FUHHQ
//:/7
+
//:/7
6: 6+
6FUHHQ
Before setting up, read “Precautions for use” (x pages 14 to 18).
rf
Do not use the projector and the high-powered laser equipment in the same room.
rf
Hitting of a laser beam on to the lens can damage the DLP chips.
ENGLISH - 27
Chapter 2 Getting Started — Setting up
Projection distance per projection lens
For PT-DW640E
When the screen aspect is 16:10 (unit: m)
rr
(The dimensions of the following table contain slight error.)
Optional lens
Lens type Standard zoom lens
Projection lens Model No. ET-DLE055 ET-DLE080 ET-DLE150 ET-DLE250
Throw ratio
Projection screen size Projection distance (L)
Screen diagonal
(SD)
1.27 (50") 0.673 1.077 1.92 2.56 0.87 0.87 1.09 1.45 2.12 2.54 4.06
1.52 (60") 0.808 1.292 2.32 3.08 1.06 1.05 1.32 1.75 2.55 3.07 4.89
1.78 (70") 0.942 1.508 2.72 3.61 1.24 1.23 1.54 2.05 2.98 3.59 5.72
2.03 (80") 1.077 1.723 3.11 4.13 1.42 1.42 1.77 2.35 3.42 4.12 6.55
2.29 (90") 1.212 1.939 3.51 4.65 1.61 1.60 2.00 2.65 3.85 4.64 7.38
2.54 (100") 1.346 2.154 3.91 5.18 1.79 1.78 2.22 2.95 4.28 5.16 8.20
3.05 (120") 1.615 2.585 4.70 6.23 2.16 2.15 2.68 3.55 5.15 6.21 9.86
3.81 (150") 2.019 3.231 5.90 7.80 2.71 2.70 3.36 4.45 6.45 7.79 12.35
5.08 (200") 2.692 4.308 7.88 10.42 3.63 3.61 4.49 5.95 8.61 10.41 16.49
6.35 (250") 3.365 5.385 9.87 13.04 4.53 5.62 7.45 10.78 13.03 20.63
7.62 (300") 4.039 6.462 11.86 15.66 5.45 6.76 8.95 12.95 15.65 24.77
8.89 (350") 4.712 7.539 13.85 18.28 6.36 7.89 10.46 15.11 18.28 28.91
10.16 (400") 5.385 8.616 15.83 20.90 7.28 9.02 11.96 17.28 20.90 33.05
12.7 (500") 6.731 10.770 19.81 26.15 9.11 11.29 14.96 21.61 26.14 41.34
15.24 (600") 8.077 12.923 23.78 31.39 10.94 13.55 17.96 25.94 31.39 49.62
*1
1.8 – 2.4:1 0.8:1 0.8 – 1.0:1 1.4 – 2.0:1 2.4 – 3.8:1
Height
(SH)
Width
(SW)
Min. Max. Fixed Min. Max. Min. Max. Min. Max.
Fixed-
focus
lens
Ultra-short focus
zoom lens
Short focus zoom
lens
Medium focus zoom
lens
Optional lens
Lens type
Projection lens Model No. ET-DLE350 ET-DLE450 Standard zoom
Throw ratio
Projection screen size Projection distance (L)
Screen diagonal
(SD)
1.27 (50") 0.673 1.077 4.00 6.11 5.96 9.59
1.52 (60") 0.808 1.292 4.83 7.36 7.21 11.57
1.78 (70") 0.942 1.508 5.65 8.61 8.46 13.55
2.03 (80") 1.077 1.723 6.48 9.86 9.71 15.53
2.29 (90") 1.212 1.939 7.31 11 .11 10.96 17.51
2.54 (100") 1.346 2.154 8.13 12.36 12.21 19.49
3.05 (120") 1.615 2.585 9.79 14.86 14.72 23.45
3.81 (150") 2.019 3.231 12.27 18.61 18.47 29.38
5.08 (200") 2.692 4.308 16.40 24.85 24.73 39.28
6.35 (250") 3.365 5.385 20.53 31.10 30.99 49.17
7.62 (300") 4.039 6.462 24.67 37.34 37.25 59.06
8.89 (350") 4.712 7.539 28.80 43.59 43.51 68.96
10.16 (400") 5.385 8.616 32.94 49.84 49.76 78.85
12.7 (500") 6.731 10.770 41.20 62.33 62.28 98.64
15.24 (600") 8.077 12.923 49.47 74.82 74.80 118.42
*1 The throw ratio is based on the value during projection onto a 2.03-m (80") screen size. *2 The height position (H) is SH/2 because lens shift cannot be used when a xed-focus lens (Model No.:ET-DLE055) is attached.
*1
3.8 – 5.7:1 5.6 – 9.0:1
Height
(SH)
Width
(SW)
Long focus zoom
lens
Min. Max. Min. Max.
Ultra-long focus
zoom lens
Height position
lens/ ET-DLE080/ ET-DLE150/ ET-DLE250/ ET-DLE350/
ET-DLE450
-
0.07 - 0.34 0.34
-
0.08 - 0.40 0.40
-
0.09 - 0.47 0.47
-
0.11 - 0.54 0.54
-
0.12 - 0.61 0.61
-
0.13 - 0.67 0.67
-
0.16 - 0.81 0.81
-
0.20 - 1.01 1.01
-
0.27 - 1.35 1.35
-
0.34 - 1.68
-
0.40 - 2.02
-
0.47 - 2.36
-
0.54 - 2.69
-
0.67 - 3.37
-
0.81 - 4.04
(H)
*2
ET-DLE055
(Fixed)
28 - ENGLISH
Chapter 2 Getting Started — Setting up
When the screen aspect is 16:9 (unit: m)
rr
(The dimensions of the following table contain slight error.)
Optional lens
Lens type Standard zoom lens
Projection lens Model No. ET-DLE055 ET-DLE080 ET-DLE150 ET-DLE250
Throw ratio
Projection screen size Projection distance (L)
Screen diagonal
(SD)
1.27 (50") 0.623 1.107 1.98 2.63 0.90 0.89 1.12 1.49 2.18 2.62 4.18
1.52 (60") 0.747 1.328 2.39 3.17 1.09 1.08 1.35 1.80 2.62 3.15 5.03
1.78 (70") 0.872 1.550 2.79 3.71 1.27 1.27 1.59 2.11 3.07 3.69 5.88
2.03 (80") 0.996 1.771 3.20 4.25 1.46 1.46 1.82 2.42 3.51 4.23 6.73
2.29 (90") 1.121 1.992 3.61 4.78 1.65 1.65 2.05 2.72 3.96 4.77 7.58
2.54 (100") 1.245 2.214 4.02 5.32 1.84 1.83 2.29 3.03 4.40 5.31 8.43
3.05 (120") 1.494 2.657 4.84 6.40 2.22 2.21 2.75 3.65 5.29 6.39 10.14
3.81 (150") 1.868 3.321 6.06 8.02 2.79 2.78 3.45 4.58 6.63 8.01 12.69
5.08 (200") 2.491 4.428 8.10 10.71 3.73 3.72 4.61 6.12 8.86 10.70 16.95
6.35 (250") 3.113 5.535 10.15 13.40 4.66 5.78 7.66 11.08 13.40 21.21
7.62 (300") 3.736 6.641 12.19 16.10 5.60 6.94 9.21 13.31 16.09 25.46
8.89 (350") 4.358 7.748 14.23 18.79 6.54 8.11 10.75 15.53 18.79 29.72
10.16 (400") 4.981 8.855 16.27 21.49 7.48 9.27 12.29 17.76 21.48 33.98
12.7 (500") 6.226 11.069 20.36 26.87 9.36 11.60 15.38 22.21 26.87 42.49
15.24 (600") 7.472 13.283 24.44 32.26 11.24 13.93 18.46 26.66 32.26 51.00
*1
1.8 – 2.4:1 0.8:1 0.8 – 1.0:1 1.4 – 2.0:1 2.4 – 3.8:1
Height
(SH)
Width
(SW)
Min. Max. Fixed Min. Max. Min. Max. Min. Max.
Fixed-
focus
lens
Ultra-short focus
zoom lens
Short focus zoom
lens
Medium focus zoom
lens
Optional lens
Lens type
Projection lens Model No. ET-DLE350 ET-DLE450 Standard zoom
Throw ratio
Projection screen size Projection distance (L)
Screen diagonal
(SD)
1.27 (50") 0.623 1.107 4.11 6.29 6.13 9.87
1.52 (60") 0.747 1.328 4.96 7.57 7.42 11.90
1.78 (70") 0.872 1.550 5.81 8.85 8.70 13.94
2.03 (80") 0.996 1.771 6.66 10.14 9.99 15.97
2.29 (90") 1.121 1.992 7.51 11.42 11.28 18.00
2.54 (100") 1.245 2.214 8.36 12.71 12.56 20.04
3.05 (120") 1.494 2.657 10.06 15.27 15.14 24.11
3.81 (150") 1.868 3.321 12.61 19.13 18.99 30.21
5.08 (200") 2.491 4.428 16.86 25.55 25.43 40.38
6.35 (250") 3.113 5.535 21.11 31.97 31.86 50.54
7.62 (300") 3.736 6.641 25.36 38.39 38.29 60.71
8.89 (350") 4.358 7.748 29.61 44.81 44.72 70.88
10.16 (400") 4.981 8.855 33.86 51.23 51.16 81.05
12.7 (500") 6.226 11.069 42.35 64.07 64.02 101.39
15.24 (600") 7.472 13.283 50.85 76.91 76.88 121.73
*1 The throw ratio is based on the value during projection onto a 2.03-m (80") screen size. *2 The height position (H) is SH/2 because lens shift cannot be used when a xed-focus lens (Model No.:ET-DLE055) is attached.
*1
3.8 – 5.7:1 5.6 – 9.0:1
Height
(SH)
Width
(SW)
Long focus zoom
lens
Min. Max. Min. Max.
Ultra-long focus
zoom lens
Height position
lens/ ET-DLE080/ ET-DLE150/ ET-DLE250/ ET-DLE350/
ET-DLE450
-
0.14 - 0.31 0.31
-
0.16 - 0.37 0.37
-
0.19 - 0.44 0.44
-
0.22 - 0.50 0.50
-
0.25 - 0.56 0.56
-
0.27 - 0.62 0.62
-
0.33 - 0.75 0.75
-
0.41 - 0.93 0.93
-
0.55 - 1.25 1.25
-
0.68 - 1.56
-
0.82 - 1.87
-
0.96 - 2.18
-
1.10 - 2.49
-
1.37 - 3.11
-
1.64 - 3.74
(H)
*2
ET-DLE055
(Fixed)
ENGLISH - 29
Chapter 2 Getting Started — Setting up
When the screen aspect is 4:3 (unit: m)
rr
(The dimensions of the following table contain slight error.)
Optional lens
Lens type Standard zoom lens
Projection lens Model No. ET-DLE055 ET-DLE080 ET-DLE150 ET-DLE250
Throw ratio
Projection screen size Projection distance (L)
Screen diagonal
(SD)
1.27 (50") 0.762 1.016 2.18 2.90 0.99 0.99 1.24 1.65 2.40 2.89 4.61
1.52 (60") 0.914 1.219 2.63 3.50 1.20 1.20 1.50 1.99 2.89 3.48 5.55
1.78 (70") 1.067 1.422 3.08 4.09 1.41 1.40 1.75 2.33 3.38 4.08 6.48
2.03 (80") 1.219 1.626 3.53 4.68 1.62 1.61 2.01 2.67 3.87 4.67 7.42
2.29 (90") 1.372 1.829 3.98 5.28 1.82 1.82 2.26 3.00 4.36 5.26 8.36
2.54 (100") 1.524 2.032 4.43 5.87 2.03 2.03 2.52 3.34 4.85 5.86 9.30
3.05 (120") 1.829 2.438 5.33 7.06 2.45 2.44 3.03 4.02 5.83 7.04 11.17
3.81 (150") 2.286 3.048 6.68 8.84 3.07 3.06 3.80 5.04 7.31 8.82 13.98
5.08 (200") 3.048 4.064 8.93 11.80 4.11 4.10 5.09 6.74 9.76 11.79 18.67
6.35 (250") 3.810 5.080 11.18 14.77 5.13 6.37 8.44 12.21 14.76 23.36
7.62 (300") 4.572 6.096 13.43 17.73 6.17 7.65 10.14 14.66 17.73 28.05
8.89 (350") 5.334 7.112 15.68 20.70 7.21 8.93 11.84 17.11 20.70 32.74
10.16 (400") 6.096 8.128 17.93 23.67 8.24 10.22 13.54 19.56 23.67 37.42
12.7 (500") 7.620 10.160 22.43 29.60 10.31 12.78 16.94 24.47 29.60 46.80
15.24 (600") 9.144 12.192 26.92 35.53 12.39 15.35 20.34 29.37 35.54 56.17
*1
2.2 – 2.9:1 1.0:1 1.0 – 1.2:1 1.6 – 2.4:1 2.9 – 4.6:1
Height
(SH)
Width
(SW)
Min. Max. Fixed Min. Max. Min. Max. Min. Max.
Fixed-
focus
lens
Ultra-short focus
zoom lens
Short focus zoom
lens
Medium focus zoom
lens
Optional lens
Lens type
Projection lens Model No. ET-DLE350 ET-DLE450 Standard zoom
Throw ratio
Projection screen size Projection distance (L)
Screen diagonal
(SD)
1.27 (50") 0.762 1.016 4.54 6.94 6.78 10.90
1.52 (60") 0.914 1.219 5.48 8.35 8.20 13.14
1.78 (70") 1.067 1.422 6.42 9.76 9.61 15.38
2.03 (80") 1.219 1.626 7.35 11.18 11.03 17.62
2.29 (90") 1.372 1.829 8.29 12.59 12.45 19.86
2.54 (100") 1.524 2.032 9.22 14.01 13.87 22.10
3.05 (120") 1.829 2.438 11.09 16.83 16.70 26.58
3.81 (150") 2.286 3.048 13.90 21.08 20.95 33.30
5.08 (200") 3.048 4.064 18.58 28.15 28.03 44.49
6.35 (250") 3.810 5.080 23.26 35.22 35.12 55.69
7.62 (300") 4.572 6.096 27.94 42.29 42.20 66.89
8.89 (350") 5.334 7.112 32.62 49.36 49.28 78.09
10.16 (400") 6.096 8.128 37.30 56.43 56.37 89.29
12.7 (500") 7.620 10.160 46.65 70.57 70.53 111.68
15.24 (600") 9.144 12.192 56.01 84.71 84.70 134.08
*1 The throw ratio is based on the value during projection onto a 2.03-m (80") screen size. *2 The height position (H) is SH/2 because lens shift cannot be used when a xed-focus lens (Model No.:ET-DLE055) is attached.
*1
4.5 – 6.9:1 6.8 – 10.8:1
Height
(SH)
Width
(SW)
Long focus zoom
lens
Min. Max. Min. Max.
Ultra-long focus
zoom lens
Height position
lens/ ET-DLE080/ ET-DLE150/ ET-DLE250/ ET-DLE350/
ET-DLE450
-
0.08 - 0.38 0.38
-
0.09 - 0.46 0.46
-
0.11 - 0.53 0.53
-
0.12 - 0.61 0.61
-
0.14 - 0.69 0.69
-
0.15 - 0.76 0.76
-
0.18 - 0.91 0.91
-
0.23 - 1.14 1.14
-
0.30 - 1.52 1.52
-
0.38 - 1.91
-
0.46 - 2.29
-
0.53 - 2.67
-
0.61 - 3.05
-
0.76 - 3.81
-
0.91 - 4.57
(H)
*2
ET-DLE055
(Fixed)
30 - ENGLISH
Loading...
+ 102 hidden pages