Panasonic PT-D12000E, PT-DZ12000E Operating Instruction

Download

Operating Instructions

3-chip DLP®-based Projector

Commercial Use

Models No.

PT-D12000E PT-DZ12000E

Read these instructions completely before operating this unit.

TQBJ 0264-5

Dear Panasonic Customer:

This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic

based projector.

DLP The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required.

Model number: PT-D12000E/PT-DZ12000E

Serial number:

2 –

ENGLISH

Be sure to read the “IMPORTANT SAFETY NOTICE” and

IMPORTANT SAFETY NOTICE ････････････････････････････････････････････････････4 Precautions with regard to safety ･････････････････････････････････････････････････6 Before Using ･･････････････････････････････････････････････････････････････････ 10 Location and function of each part ･･････････････････････････････････････････････ 12 Using the remote control unit ･･･････････････････････････････････････････････････ 17 Installation ････････････････････････････････････････････････････････････････････ 19 Connection ････････････････････････････････････････････････････････････････････ 27 Installation of input module (optional) ･･･････････････････････････････････････････ 30 How to install and remove the projection lens (optional) ･･････････････････････････ 36

Projection ･････････････････････････････････････････････････････････････････････ 37 How to adjust the lens ･････････････････････････････････････････････････････････ 40 Registration of input signal data ････････････････････････････････････････････････ 45 Basic operations using the remote control ･･････････････････････････････････････ 48 On-screen menus ･･････････････････････････････････････････････････････････････ 51 Adjusting the picture ･･･････････････････････････････････････････････････････････ 54 Adjusting the position ･･････････････････････････････････････････････････････････ 60 How to use ADVANCED MENU ･････････････････････････････････････････････････ 64 Setting the DISPLAY LANGUAGE ･･･････････････････････････････････････････････ 69

the “Precautions with regard to safety”. (pp. 4-9)

Getting Started

Basic OperationSpecial FeaturesInformation

Display Option settings ････････････････････････････････････････････････････････ 70 Projector setup ････････････････････････････････････････････････････････････････ 77 P IN P ･････････････････････････････････････････････････････････････････････････ 85 Displaying the internal test pattern ･･････････････････････････････････････････････ 87 Setting the security ････････････････････････････････････････････････････････････ 88 How to use network function ･･･････････････････････････････････････････････････ 91 Using the PJLink™ protocol ･･･････････････････････････････････････････････････ 105 Using the serial terminals ･････････････････････････････････････････････････････ 106 Using the Remote 2 terminal ･･････････････････････････････････････････････････ 110

Indication of monitor lamp ････････････････････････････････････････････････････ 111 Cleaning and replacement of air filter ･･････････････････････････････････････････ 112 Replacement of lamp unit ･････････････････････････････････････････････････････ 114 Notes when installing the ceiling mount bracket ････････････････････････････････ 116 Before asking for service Self-diagnosis display ･････････････････････････････････････････････････････････ 118 Specifications ････････････････････････････････････････････････････････････････ 120 Appendix ･････････････････････････････････････････････････････････････････････ 122 Dimensions ･･････････････････････････････････････････････････････････････････ 125 Index ････････････････････････････････････････････････････････････････････････ 126

… try to check the following points again. ････････････････････････････････117

ENGLISH

– 3

IMPORTANT SAFETY NOTICE

WARNING: THIS APPARATUS MUST BE EARTHED.

WARNING: To prevent damage which may result in fire or shock hazard, do not

expose this appliance to rain or moisture.

Machine Noise Information Ordinance 3. GSGV, January 18 1991: The sound pressure level at the operator position is equal or less than 70 dB (A) according to ISO 7779.

WARNING:

1) Remove the plug from the wall outlet when this unit is not in use for a prolonged period of time.

2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel.

3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three prong earthingtype power plug. This plug will only fit an earthing-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the earthing plug.

CAUTION:

To assure continued compliance, follow the attached installation instructions, which include using the shielded interface cables when connecting to a computer or peripheral device.

Pursuant to at the directive 2004/108/EC, article 9(2) Panasonic Testing Centre Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg, F.R. Germany

4 –

ENGLISH

IMPORTANT: THE MOULDED PLUG (U.K. only)

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSl to BS1362. Check for the ASTA mark a or the BSl mark ` on the body of the fuse. If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from an Authorized Service Centre.

If the fitted moulded plug is unsuitable for the socket outlet in your home, then the fuse should be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

WARNING: –THIS APPLIANCE MUST BE EARTHED. IMPORTANT: –The wires in this mains lead are coloured in accordance with the following code: – Green-and-Yellow: Earth Blue: Neutral Brown: Live

Getting Started

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol W or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

FUSE

ENGLISH

– 5

Precautions with regard to safety

WARNING

If a problem occurs (such as no image) or if you notice smoke or



a strange smell coming from the projector, turn off the power and disconnect the power cord from the wall outlet.

Do not continue to use the projector in such cases, otherwise fire or electric shocks could result.• Check that no more smoke is coming out, and then contact an Authorized Service Centre for repairs.• Do not attempt to repair the projector yourself, as this can be dangerous.•

Do not install this projector in a place which is not strong enough to



take the full weight of the projector.

If the installation location is not strong enough, it may fall down or tip over, and severe injury or • damage could result.

Installation work (such as ceiling suspension) should only be carried out by a qualified technician.• If installation is not carried out correctly, there is the danger that injury or electric shocks may occur.•

If foreign objects or water get inside the projector, or if the projector



is dropped or the cabinet is broken, turn off the power and disconnect the power cord from the wall outlet.

Continued use of the projector in this condition may result in fire or electric shocks.• Contact an Authorized Service Centre for repairs.•

Do not cover the air filter, the air inlet and exhaust vents.



Doing so may cause the projector to overheat, which can cause fire or damage to the projector.•

Do not overload the wall outlet.



If the power supply is overloaded (for example, by using too many adapters), overheating may occur • and fire may result.

Do not remove the cover or modify it in any way.



High voltages which can cause fire or electric shocks are present inside the projector.• For any inspection, adjustment and repair work, please contact an Authorized Service Centre.•

Clean the power cord plug regularly to prevent it from becoming



covered in dust.

If dust builds up on the power cord plug, the resulting humidity can damage the insulation, which • could result in fire. Pull the power cord out from the wall outlet and wipe it with a dry cloth.

If not using the projector for an extended period of time, pull the power cord plug out from the wall • outlet.

Do not do anything that might damage the power cord or the power



cord plug.

Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it • excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle.

If the power cord is used while damaged, electric Shocks, short-circuits or fire may result.• Ask an Authorized Service Centre to carry out any repairs to the power cord that might be necessary.•

6 –

Do not handle the power cord plug with wet hands.



Failure to observe this may result in electric shocks.•

Insert the power cord plug securely into the wall outlet.



If the plug is not inserted correctly, electric shocks or overheating could result.• Do not use plugs which are damaged or wall outlets which are coming loose.•

ENGLISH

Do not place the projector on top of surfaces which are unstable.



If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over, • and injury or damage could result.

Do not place the projector into water or let it become wet.



Failure to observe this may result in fire or electric shocks.•

Do not disassemble the lamp unit.



If the lamp section breaks, it may cause injury.•

Do not place liquid containers on top of the projector.



If water spills onto the projector or gets inside it, fire or electric shocks could result.• If any water gets inside the projector, contact an Authorized Service Centre. •

Do not insert any foreign objects into the projector.



Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, • as doing so can result in fire or electric shocks.

After removing the battery from remote control unit, keep it away from



the reach of children.

The battery can cause death by suffocation if swallowed.• If the battery is swallowed, seek medical advice immediately.•

Do not allow the + and - terminals of the battery to come into contact



with metallic objects such as necklaces or hairpins.

Failure to observe this may cause the battery to leak, overheat, explode or catch fire.• Store the battery in a plastic bag and keep it away from metallic objects.•

Getting Started

Insulate the battery using tape or similar before disposal.



If the battery comes into contact with metallic objects or other batteries, it may catch fire or explode.•

Replacement of the lamp unit should be carried out by a qualified



technician.

The lamp unit has high internal pressure. If improperly handled, failure might result.• The lamp unit can easily become damaged if struck against hard objects or dropped, and injury or •

malfunctions may result.

When installing to a ceiling, be sure to use the accessory wire (install



in a different location to the ceiling mount bracket) and the eye bolts as an extra preventative measure to stop the projector from falling down.

If the projector is not secure enough, accidents may result.•

Do not place sets directly on top of each other.



If this is not observed, accidents may result.•

Do not use the projector while the projection lens cover is still



attached to the projection lens (sold separately).

If this is not observed, fire may occur.•

Do not look into the lens while the projector is being used.



Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and • damage your eyes.

Do not place your skin into the light beam while the projector is being



used.

Strong light is emitted from the projector’s lens. If you place directly into this light, it can hurt or • damage your skin.

ENGLISH

– 7

Precautions with regard to safety (continued)

CAUTION

Do not set up the projector in humid or dusty places or in places



where the projector may come into contact with smoke or steam.

Using the projector under such conditions may result in fire or electric shocks.•

When disconnecting the power cord, hold the plug, not the cord.



If the power cord itself is pulled, the cord will become damaged, and fire, short-circuits or serious • electric shocks may result.

Always disconnect all cables before moving the projector.



Moving the projector with cables still attached can damage the cables, which could cause fire or • electric shocks to occur.

Do not place any heavy objects on top of the projector.



Failure to observe this may cause the projector to become unbalanced and fall, which could result in • damage or injury.

Do not short-circuit, heat or disassemble the battery or place it into



water or fire.

Failure to observe this may cause the battery to overheat, leak, explode or catch fire, and burns or other • injury may result.

When inserting the battery, make sure the polarities (+ and -) are



correct.

If the battery is inserted incorrectly, it may explode or leak, and fire, injury or contamination of the • battery compartment and surrounding area may result.

Use only the specified battery.



If an incorrect battery is used, it may explode or leak, and fire, injury or contamination of the battery • compartment and surrounding area may result close to this port, otherwise burns or damage could result.

Do not bring your hands or other objects close to the air outlet port.



Heated air comes out of the air outlet port. Do not bring your hands or face, or objects which cannot • withstand heat.

Do not use the old lamp unit.



The lamp section may break.•

Replacement of the lamp unit should only be carried out after it has



completely cooled off, otherwise burns may result. Disconnect the power cord plug from the wall outlet as a safety



precaution before carrying out any cleaning.

Electric shocks can result if this is not done.•

8 –

ENGLISH

Ask an Authorized Service Centre to clean inside the projector at least



once a year.

If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems • with operation.

It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask • your nearest Authorized Service Centre to clean the projector when required. Please discuss with the Authorized Service Centre regarding cleaning costs.

Do not reach for the openings beside the optical lens, during



horizontal or vertical movements of the lens there is a injury hazard. An effort to keep our environment clean, please bring the



non-repairable unit to your Dealer or a Recycling Company. Do not use projectors with the adjustable feet or projection lens cover



removed.

If this is not observed, the sets may not operate correctly or accidents may result.•

Getting Started

ENGLISH

– 9

Before Using

Accessories

Check that all of the accessories shown below have been included with your projector.

Remote Control

[N2QAYB000076 × 1]

Batteries for Remote

Control (AA)

For U.K.

[K2CT3YY00014 × 1]

Caution when moving the projector

Power cord Drop-prevention bracket

For Continental

[K2CM3YY00007 × 1]

Eye bolt

[TPAHE86 × 4]

Wire

[TTRA0143 × 4]

The projection lens is susceptible to vibrations and impacts. Be sure to always remove the lens during transport.

Cautions regarding setup

Be sure to observe the following precautions when installing the product.

Be sure to install the projection lens cover after installing the projection



lens.

If this is not done, dust will collect inside the projector and problems with the projector will result.

Avoid installing the product in a place exposed to vibrations or impacts.



If the projector is installed in a place where vibrations are transmitted from a source of driving power and others or mounted in a car, vibrations or impacts may be transmitted to the product to damage the internal parts, causing failure. Install the product in a place free from vibrations and impacts.

Do not install the projector near high-voltage power lines or power



sources.

The product may be exposed to interference if it is installed in the vicinity of high-voltage electrical power lines or power sources.

Do not place the projector on a vinyl sheet or carpet.



If a vinyl sheet sucked up and blocks the air filter intake port, the internal temperature of the projector may increase, which triggers the protection circuit, turning off the power.

Be sure to ask a specialized technician when to install the product to a



ceiling.

If the product is to be installed hanging from the ceiling, purchase an optional hanging attachment (for high ceiling: Model No. ET-PKD100H) (for low ceiling: Model No. ET-PKD100S) and call a specialized technician for installation.

10 –

Do not place the projector over 2 700 m above sea level. When using it



over 1 400 m above sea level, set the “ALTITUDE MODE”, described on page 78, to “ON”.

Otherwise the life of the product may be shortened.

When installing and using the projector at an angle that exceeds 30° from



the horizontal in the vertical direction, set “DIRECTION”, described on page 78, to “VERTICAL”.

ENGLISH

Notes on use

To view clear images:



The audience cannot enjoy high-contrast and clear images if outside light or the illumination interferes the • screen surface. Draw window curtains or blinds, turn off the lightings near the screen or take other proper measures. In rare cases, wafture can occur on the screen affected by the warm air from the exhaust port depending on • the environment. Make sure that there is no equipment in front of the set which will recirculate the exhaust air from the set or other nearby equipment.

Do not touch the surface of the projection lens with bare hand.



If fingerprints or stains are left on the projection lens surface, they are magnified and projected on the screen. Keep your hands away from the lens. Cover the lens with the supplied lens cap when the projector is not used.

DLP chips



The DLP chips are made using extremely high-precision technology. Note that in rare cases, pixels may be missing or always lit, but this is not a malfunction.

Lamp



A mercury lamp with high internal pressure is used for the light source of this product. A high-pressure mercury lamp has the following characteristics:

It may burst with a loud sound or end its life cycle by not illuminating because of given impacts, flaws, or • deterioration due to used hours. The life cycle of a mercury lamp varies according to the individual difference or conditions of use. In • particular, turning the power on and off frequently and/or repeatedly will greatly affect the life cycle. In rare cases, it may burst shortly after projection starts.• The possibility of burst increases when the lamp is used beyond the replacement time.• When the lamp bursts, the gas inside will be emitted and may appear like smoke.• Provide a lamp for replacement in advance.•

Getting Started

Maintenance

Be sure to remove the power cord plug from the receptacle before cleaning.

Use soft and dry cloth to clean the cabinet•

Use a soft cloth moistened in warm water to clean away oil. Do not use solvents such as benzene, thinner, and alcohol, detergents for kitchens, or a chemical cloth. If using such solvents, the outer case may become deformed, and the paint may peel off.

Do not clean the lens surface with fuzzy or dusty cloth.•

If dust adheres to the lens, it will be magnified and projected on the screen. Use a soft and clean cloth to wipe off dust.

Caution:

When connecting the projector to a PC or external device, use the power cord supplied with the corresponding device and a commercially available shielded interface cable.

Disposal

When disposing of the product, contact your nearest municipality or dealer to confirm the correct procedure for disposal.

Attention on security

If you use the network function of this product, there is the likelihood of being subjected to the following damage.

Personal information being leaked via this product• Unauthorized operation of this product by a malicious third party• Interfering or stopping of this product by a malicious third party•

Be sure to take sufficient security measures. (pp. 88-94)

Use a password that is as difficult to guess as possible. • Change your password regularly. • Panasonic and its affiliate companies would never directly inquire about your password.•

In the event that somebody does make a direct inquiry, do not let the person know your password.

Use a network for which security measures such as a firewall have been implemented. • Set a password, and place restrictions on the users who can log in.•

ENGLISH

– 11

Location and function of each part

Remote control unit

Front



2 3

j k

Remote control operation indicator lamp

The lamp flashes when any remote control button is pressed.

POWER STANDBY button ･････････ (pp. 37, 39)

When the projector is in projection mode with the MAIN POWER switch of the projector at the “ l ” side, this button switches the projector to standby mode.

POWER ON button ････････････････････ (p. 38)

When the projector is in standby mode with the MAIN POWER switch of the projector at the “ l ” side, this button switches the projector to projection mode.

Input select (RGB1, RGB2, DVI-D, VIDEO,

S-VIDEO, AUX) button ･････････････････ (p. 48)

Use to change the RGB1, RGB2, DVI-D, VIDEO, S-VIDEO and AUX (optional input module) input ports.

MENU button ･････････････････････ (pp. 51, 53)

Use this button to return to the previous screen when the sub menu is displayed. If you hold it down for at least 3 seconds while the on-screen indication is OFF, the OFF state is cancelled.

Arrow ▲▼◄►buttons ････････････(pp. 53, 88)

Use these buttons to select an item on the menu screen, change setting and adjust the level. Also use them to enter the “SECURITY” password.

q r s

ENTER button ････････････････････････ (p. 53)

Press this button to enter your menu selection or to run function.

ON SCREEN button ･･･････････････････ (p. 48)

This button turns on and off the on-screen indication function.

TEST PATTERN button ････････････････ (p. 49)

This displays the test pattern.

Numeric (0-9) buttons ･････････････ (pp. 18, 84)

These buttons are used for systems where more than one projector is being used. They are used to enter ID numbers when selecting an ID, and they are also used by service personnel for entering passwords when password entry is needed.

STATUS button ･･･････････････････････ (p. 48)

Press this button to display projector information. It can also be used to send information about the projector’s status via E-mail.

LIGHT button ･････････････････････････ (p. 49)

When this button is pressed, the remote control button light is turned on. The light goes off about 10 seconds after you stop remote control operation.

12 –

ENGLISH

Side



Top



Bottom



Getting Started

AUTO SET UP button ･･････････････････ (p. 49)

Pressing this button while projecting an image automatically corrects the picture positioning on the screen. While the auto setup feature is active, a message “PROGRESS...” appears on the screen.

SHUTTER button ･････････････････････ (p. 48)

Press this button to black out the image temporarily.

ASPECT button ･･･････････････････････ (p. 50)

Switches the image aspect ratio.

LENS (FOCUS, ZOOM, SHIFT) button ･･･ (p. 40)

These buttons are used to adjust the projection lens.

Function 1 (FUNC1) button ････････････ (p. 49)

This button can control the functions set in “FUNC1” of the “PROJECTOR SETUP” screen from MAIN MENU.

DEFAULT button ･･････････････････････ (p. 53)

Press this button when you want to restore the setting of the item selected in the menu to the factory default value.

ID SET button ････････････････････ (pp. 18, 77)

When two or more main units are used in the system, this button specifies the ID of the remote control.

ID ALL button ･････････････････････ (pp. 18, 77)

When two or more main units are used in the system, this button switches to the mode to control them simultaneously with a single remote control.

LOCK button

This button is used to prevent unintentional operation of the projector by accidentally pressing a button, and to prevent the remote control batteries from becoming spent.

Remote control transmitter window

Operate the remote control aiming at the remote control receiver window on the main unit.

Remote control wired terminal ･････････ (p. 18)

To use the wired output terminal, connect the remote control and the main unit with the cable (sold separately).

Note

The AUX button to switch the input is disabled • when an optional input module is not connected.

ENGLISH

– 13

Location and function of each part (continued)

Projector Main Unit

Front



12 3456

7n89j k l m

Projection lens cover ･･････････････････ (p. 36)

Projection lens (optional)

Lens for projecting images on the screen.

Remote control receiver window (front)

･･････････････････････････････････････ (p. 17)

This window receives the signal beam emitted from the remote control.

LAMP (LAMP1, LAMP2, LAMP3, LAMP4)

monitor ･････････････････････････････ (p. 111)

These light when it is time to replace the lamp unit. It also blinks if something unusual occurs in the lamp circuit.

Temperature monitor (TEMP) ･････････ (p. 111)

Lighting or blinking of this lamp indicates an abnormal condition of the internal temperature.

Power indicator lamp ･････････････････ (p. 37)

The lamp lights in red when the MAIN POWER switch is turned to “ l ” (on). It turns to green when the POWER ON button of the remote control or the main unit is pressed.

Air intake vents

Do not cover this vents.

Burglar hook

Attach a commercial burglar prevention cable to this hook port.

Adjustable feet ･･･････････････････････ (p. 20)

Use these feet to adjust the tilt of the projector. (Adjustable feet are provided at the front and rear, right and left.)

Rear



pq r s

Projection lens cover lock button ･･････ (p. 36)

This button toggles between lock and unlock of the detachable cover for the projection lens (optional).

Air filter ･････････････････････････････ (p. 112)

Air filter cleaning monitor･････････ (pp. 81, 112)

This blinks blue while the air filter is being cleaned. It lights red when there is a problem with the air filter.

Filter cleaning unit fixing screw ･･･････ (p. 112)

This is used to secure the air filter cover.

Air exhaust vents

Lamp unit cover screw ･･･････････････ (p. 115)

Remote control receiver window (rear) ･ (p. 17)

This also receives the signal beam coming from the remote control.

Remote control receiver window (bottom)

･･････････････････････････････････････ (p. 17)

This also receives the signal beam coming from the remote control.

Air intake vents

Do not cover this vents.

Lamp unit cover ･････････････････････ (p. 115)

The lamp unit is housed.

14 –

ENGLISH

Side



Controls



Connection

terminals (p. 16)

123

AC IN terminal ････････････････････････ (p. 37)

Connect the supplied line power cord into this receptacle. Do not connect any other cable to this socket.

MAIN POWER switch ･･････････････ (pp. 37-39)

Use this switch to turn on “I” and off “○” the commercial line power applied to the projector.

Slot cover ････････････････････････････ (p. 31)

Install the input module here.

POWER ON ( I ) button ････････････ (pp. 37, 38)

When the projector is in standby mode with the MAIN POWER switch of the projector at the “ l ” side, this button switches the projector to projection mode.

POWER STANDBY ( ) button ･･････(pp. 37, 39)

When the projector is in projection mode with the MAIN POWER switch of the projector at the “ l ” side, this button switches the projector to standby mode.

MENU button ･････････････････････ (pp. 51, 53)

Use this button to return to the previous screen when the sub menu is displayed. If you hold it down for at least 3 seconds while the on-screen indication is OFF, the OFF state is cancelled.

Arrow ▲▼◄► buttons ････････････ (pp. 53, 88)

Use to select an item on the menu screen, change setting and adjust the level. Also use them to enter the “SECURITY” password.

Controls

4j5k6l7

LENS button ･･････････････････････････ (p. 40)

Switches to the adjustment mode for lens focus, zoom and shift (position).

ENTER button ････････････････････････ (p. 53)

Press this button to enter your menu selection or to run function.

Input select (VIDEO, S-VIDEO, RGB1, RGB2,

DVI-D, AUX) button ･･･････････････････ (p. 48)

Use to change the VIDEO, S-VIDEO, RGB1, RGB2, DVI-D and AUX (optional input module) input ports.

AUTO SETUP button ･･････････････････ (p. 49)

Pressing this button while projecting an image automatically corrects the picture positioning on the screen. While the auto setup feature is active, a message “PROGRESS...” appears on the screen.

Self-diagnosis display ･･･････････ (pp. 118-119)

LIGHT ON/OFF button

This switch is used for illuminating the connection terminals and controls.

SHUTTER button ･････････････････････ (p. 48)

Press this button to black out the image temporarily.

8n9

Note

The AUX button to switch the input is disabled • when an optional input module is not connected.

Getting Started

ENGLISH

– 15

Location and function of each part (continued)

Connection terminals



7289 jk l

3456

REMOTE1 lN/OUT terminal ････････････ (p. 18)

When two or more main units are used in the system, they can be connected and controlled with a wired remote control cable (M3 jack).

REMOTE2 IN terminal ････････････････ (p. 110)

The user can remotely control the main unit by using an external control circuit to this terminal (D-SUB 9-pin female).

SERIAL IN terminal････ (pp. 28-29, 80, 106-109)

This terminal is an RS-232C compliant input terminal (switching necessary) to connect a PC and to externally control the main unit (D-SUB 9-pin female).

SERIAL IN terminal････ (pp. 28-29, 80, 106-109)

This terminal is an RS-422 compliant input terminal (switching necessary) to connect a PC and to externally control the main unit (D-SUB 9-pin female).

SERIAL OUT terminal ････････(pp. 29, 106-109)

This terminal is an RS-422 compliant output terminal (switching necessary) to supply signals given to the serial input terminal (D-SUB 9-pin male).

LAN terminal (10BASE-T/100BASE-TX)

･･･････････････････････････････ (pp. 28-29, 93)

This terminal is used for connecting a LAN cable.

VIDEO IN terminal･････････････････････ (p. 28)

An input terminal for video signals. (BNC)

VIDEO OUT terminal ･･････････････････ (p. 28)

An output terminal (active through) for video signals. (BNC)

S-VIDEO IN terminal ･･････････････････ (p. 28)

An input terminal for S-video signals (Mini DIN 4-pin). This terminal complies with S1 signals and automatically toggles between 16:9 and 4:3 according to the size of input signals.

RGB (YPBPR) 1 IN terminal ･････････ (pp. 28, 29)

A terminal to input RGB or YPBPR signals (BNC).

RGB2 IN terminal ･････････････････････ (p. 29)

A terminal to input RGB or YPBPR signals (D-SUB 15-pin female).

DVI-D IN terminal ･････････････････ (pp. 28, 29)

An input terminal for DVI-D signals.

16 –

ENGLISH

Using the remote control unit

Loading batteries

When loading supplied AA batteries into the battery compartment of the Remote Control, make sure that their polarities are correct.

Open battery compartment lid.1.

and then 2.

Open the lid in the order •

Insert the batteries.2.

Into battery compartment, with their • polarities orientated as indicated (⊕,⊖) in the compartment.

Supplied AA batteries (insert the ⊖ side first).

Effective range of remote control operation

The Remote Control should normally be aimed at either the front or rear remote control receiver window on the projector (figure 1). The effective control range is approx. 30 metres from the beam receiver on the front or rear. Otherwise, it may also be aimed at the screen, which will reflect commands back to the projector’s front receiver window as illustrated in figure 2.

When the Remote Control is aimed at the screen, • the effective control range may be reduced due to the optical loss by screen reflection.

Figure 1

Top View•

(Front) (Rear)

30°

Remote Control

30°

Getting Started

Close the battery compartment 3. lid.

Replace the battery compartment lid over the • compartment and slide until it clicks.

Attention

Do not drop the Remote Control unit.• Do not expose Remote Control unit to any liquid.• Do not use NiCd batteries.• Release the LOCK button before operating the •

remote control. (p. 13)

Side View•

Remote Control

Figure 2

Screen

Remote Control

30° 30°

15°

Remote Control

30° 30°

Projector

Remote Control receiver window (front)

15°

Remote Control

Remote Control receiver window (rear)

Remote Control

ENGLISH

– 17

Using the remote control unit (continued)

Note

The Remote Control may not function properly if an • object is in the light path.

The Remote Control receiver may not function • properly in intense ambient light such as fluorescent lamps. Carefully site the projector so its Remote Control receiver windows will not be directly exposed to intense light.

Setting projector ID number to remote control

Every projector has its ID number and the ID number of the controlling projector must be set to the remote control in advance so that the user can operate the remote control. (p. 77) The ID number of the

projector is set to “ALL” on shipping, and use the ID ALL button of the remote control when using only a single projector.

Press ID SET, and then within 1. 5 seconds, press the two numeric (0-9) buttons which correspond to the ID number that has been set for the projector.

Using a wired remote control

When multiple main units are connected as part of the system, connect to units with a M3 stereo mini jack cable (sold separately) to simultaneously control multiple main units with a single remote control through the REMOTE1 IN/OUT terminal. It is effective to use the wired remote control in the environment in which an obstacle stands in the light path or where devices are susceptible to outside light.

Connect to the secondary projector

Connection terminals

M3 stereo mini pin-PIN cable (sold separately)

Attention

Do not press the ID SET button accidentally or • carelessly because the ID number on the Remote Control can be set even when no projector is around.

If you do not enter the two-digit ID number within • 5 seconds after the ID SET button has been pressed, the ID number will remain at the number that was set before the ID SET button was pressed.

Your specified ID number is stored in the remote • control unit unless another one is specified later. However, the stored ID will be erased if the batteries of the remote control are left exhausted. When the batteries are replaced, set the same ID number again.

The ID number can be set to “ALL” or from “1” to • “64”.

Remote Control

Attention

Use a two-wire shielded cable with a length of 15 m • or less. If the length of the cable exceeds 15 m, the shielding of the cable may not be sufficient and the remote control may not work.

18 –

ENGLISH

Installation

Examples of system expansion

The projector is provided with a number of terminals and optional accessories to enable various system expansions. Both input and output are provided to all terminals on the main unit. The following are some examples of system expansion:

System 1

The optional high- or low-ceiling mount bracket flexibly fits the projector in individual site conditions.

Getting Started

System 2

Connection to a computer via the DVI-D IN terminal or DVI-D input module (optional).

System 3

Soft adjustments can be performed using geometrical distortion compensation.

Panasonic

ENGLISH

– 19

Installation (continued)

Adjusting the feet

The four adjustable feet (p. 14) mounted at the bottom of the projector are level-adjustable (0 mm–15 mm) which can be used when the floor surface is not horizontal.

(Front) (Rear)

Projection scheme

This projector can use any of the four projection schemes. Select the most suitable scheme to the situation of your location. Use the INSTALLATION menu to choose the desired projection scheme. (p. 78)

Installation geometry

When planning the projector and screen geometry, refer to the figures below and the information on the next page for reference. After the projector is roughly positioned, picture size and vertical picture positioning can be finely adjusted with the powered zoom lens and lens shifting mechanism.

When attaching an optional ceiling mount bracket (ET-PKD100H)

Side View

(unit : mm)

580.5 - 700.5

254

Screen

L Projection distance SH Height of the image SW Image width

Vertical distance between the lens centre level and

the bottom edge of the projected image

* For PT-D12000E: H = 0 to SH For PT-DZ12000E: H = -0.1 × SH to 1.1 × SH * However, if the ET-D75LE5 has been installed,

the value will be fixed at H=SH/2 for both the PT-D12000E and PT-DZ12000E. If the ET-D75LE6 has been installed, the values will be H = 0.1 × SH to 0.9 × SH for the PT-D12000E, and H = 0 to SH for the PT-DZ12000E.

Top View (unit : mm)

200

Screen

254

175

120

314

Lens Dimension of L1 (Approx.)

ET-D75LE1 62.5 ET-D75LE2 47 ET-D75LE3 50.5 ET-D75LE4 74.4 ET-D75LE5 150.5 ET-D75LE6 160 ET-D75LE8 202.5

20 –

ENGLISH

Projected range using geometric adjustment

VERTICAL KEYSTONE HORIZONTAL KEYSTONE

Side View Top View

Screen

VERTICAL ARC HORIZONTAL ARC

Side View Top View

L2 : Projection distance R2 : Radius of the circle

Screen

Getting Started

L2 : Projection distance R2 : Radius of the circle

Side View Top View

Centre of the circle

Screen

Keystone correction only

Lens

ET-D75LE1 ±40 ±15 ±5 ±5 1.6 3.2 0.8 1.6 ET-D75LE2 ±40 ±15 ±5 ±5 1.2 2.4 0.6 1.2 ET-D75LE3 ±40 ±15 ±10 ±10 0.8 1.6 0.4 0.8 ET-D75LE4 ±40 ±15 ±10 ±15 0.6 1.0 0.3 0.5 ET-D75LE5 ±22 ±15 ±5 ±5 3.0 6.0 1.5 3.0 ET-D75LE6 ±28 ±10 ±5 ±5 2.4 4.8 1.2 2.4 ET-D75LE8 ±40 ±15 ±10 ±15 0.4 0.8 0.2 0.4

Vertical

Keystone

Correction Angle α( ° )

L3 : Projection distance R3 : Radius of the circle

When using arc and keystone correction together Arc correction only

Horizontal

Keystone

Correction Angle β( ° )

Vertical

Keystone

Correction

Angle α( ° )

Horizontal

Keystone

Correction Angle β( ° )

Centre of the circle

Screen

R2/L2

minimum

value

R3/L3

minimum

value

L3 : Projection distance R3 : Radius of the circle

R2/L2

minimum

value

R3/L3

minimum

value

Note

When using geometric adjustment, if the amount of compensation is too great, focusing for the entire screen • may become blurred. When using the arc screen, make the screen the same shape as an arc created by cutting away a portion of a • full circle.

ENGLISH

– 21

Installation (continued)

Projection distances by the type of projection lenses (optional)

Every type of optional projection lenses has a different projection distance to achieve the same screen size. Select and purchase a projection lens most suitable to the size of your location referring to the following tables and the projection distances by the type of projection lenses on the next page.

Side View

Screen

Top View

Screen

L : Projection distance

SH : Effective screen height SW : Effective screen width

Note

The projection distances listed here involve an error of ±5 %.• When using geometric adjustment, alter the compensation so that the screen size becomes smaller than the •

specified size.

Projection distances by the type of projection lenses (for PT-DZ12000E)



For the screen aspect ratio of 16:10 (Units: m)

Lens type Zoom lens

Model number of

projection lens

Throw ratio

Screen dimensions Projection distance (L)

Screen

Effective

size

(inch)

70 0.942 1.508 2.01 2.69 2.72 4.10 4.11 6.90 6.91 11.06 10.78 20.56 1.35 1.62 0.99 80 1.077 1.723 2.31 3.09 3.12 4.70 4.71 7.90 7.91 12.66 12.37 23.55 1.55 1.86 1.15

90 1.212 1.939 2.61 3.49 3.52 5.30 5.31 8.91 8.91 14.25 13.97 26.54 1.76 2.10 1.30 100 1.346 2.154 2.91 3.89 3.92 5.90 5.91 9.91 9.91 15.85 15.57 29.53 1.96 2.34 1.45 120 1.615 2.585 3.51 4.68 4.73 7.10 7.11 11.91 11.92 19.04 18.76 35.50 2.36 2.82 1.76 150 2.019 3.231 4.40 5.88 5.93 8.90 8.91 14.92 14.93 23.82 23.54 44.47 2.96 3.55 2.22 200 2.692 4.308 5.89 7.87 7.93 11.91 11.92 19.94 19.95 31.80 31.52 59.41 3.97 4.75 2.99 250 3.365 5.385 7.39 9.87 9.93 14.91 14.92 24.95 24.96 39.77 39.49 74.36 4.98 5.96 3.76 300 4.039 6.462 8.88 11.86 11.93 17.91 17.92 29.97 29.98 47.75 47.47 89.30 5.99 7.17 4.53 350 4.712 7.539 10.37 13.86 13.93 20.91 20.92 34.98 34.99 55.72 55.44 104.24 6.99 8.37 400 5.385 8.616 11.86 15.85 15.94 23.92 23.93 40.00 40.01 63.70 63.42 119.19 8.00 9.58 500 6.731 10.770 14.85 19.84 19.94 29.92 29.93 50.03 50.04 79.65 79.37 149.08 10.01 11.99 600 8.077 12.923 17.83 23.82 23.94 35.93 35.94 60.06 60.07 95.60 95.32 178.96 12.03 14.40

height

(SH)

Effective

width

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8 ET-D75LE6 ET-D75LE5

(SW)

1.4-1.8 : 1 1.8-2.8 : 1 2.8-4.6 : 1 4.6-7.4 : 1 7.3-13.8 : 1 0.9-1.1 : 1 0.7 : 1

Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Fixed

Fixed-focus

lens

22 –

ENGLISH

For the screen aspect ratio of 16:9 (Units: m)

Lens type Zoom lens

Model number of

projection lens

Throw ratio

Screen dimensions Projection distance (L)

Screen

Effective

size

(inch)

70 0.872 1.550 2.07 2.77 2.80 4.21 4.23 7.09 7.10 11.37 11.09 21.14 1.39 1.66 1.02 80 0.996 1.771 2.38 3.18 3.21 4.83 4.84 8.13 8.13 13.01 12.73 24.21 1.60 1.91 1.18

90 1.121 1.992 2.68 3.59 3.62 5.45 5.46 9.16 9.16 14.65 14.37 27.29 1.81 2.16 1.34 100 1.245 2.214 2.99 4.00 4.04 6.07 6.08 10.19 10.19 16.29 16.01 30.36 2.01 2.41 1.50 120 1.494 2.657 3.60 4.82 4.86 7.30 7.31 12.25 12.26 19.57 19.29 36.50 2.43 2.90 1.81 150 1.868 3.321 4.53 6.05 6.09 9.15 9.16 15.34 15.35 24.49 24.21 45.72 3.05 3.65 2.29 200 2.491 4.428 6.06 8.10 8.15 12.24 12.25 20.50 20.50 32.69 32.40 61.08 4.08 4.89 3.08 250 3.113 5.535 7.59 10.15 10.21 15.33 15.34 25.65 25.66 40.88 40.60 76.44 5.12 6.13 3.87 300 3.736 6.641 9.13 12.19 12.27 18.41 18.42 30.81 30.81 49.08 48.80 91.79 6.15 7.37 4.66 350 4.358 7.748 10.66 14.24 14.32 21.50 21.51 35.96 35.97 57.28 57.00 107.15 7.19 8.61 400 4.981 8.855 12.19 16.29 16.38 24.58 24.60 41.12 41.12 65.47 65.19 122.51 8.22 9.85 500 6.226 11.069 15.26 20.39 20.50 30.76 30.77 51.42 51.43 81.87 81.59 153.23 10.29 12.33 600 7.472 13.283 18.33 24.49 24.61 36.93 36.94 61.73 61.74 98.26 97.98 183.95 12.36 14.81

height

(SH)

Effective

width

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8 ET-D75LE6 ET-D75LE5

(SW)

1.4-1.8 : 1 1.8-2.8 : 1 2.8-4.6 : 1 4.6-7.4 : 1 7.3-13.8 : 1 0.9-1.1 : 1 0.7 : 1

Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Fixed

Fixed-focus

lens

Getting Started

For the screen aspect ratio of 4:3 (Units: m)

Lens type Zoom lens

Model number of

projection lens

Throw ratio

Screen dimensions Projection distance (L)

Screen

Effective

size

(inch)

70 1.067 1.422 2.29 3.06 3.09 4.65 4.66 7.83 7.83 12.54 12.25 23.32 1.54 1.84 1.13

80 1.219 1.626 2.63 3.51 3.55 5.33 5.34 8.96 8.97 14.34 14.06 26.71 1.77 2.11 1.31

90 1.372 1.829 2.96 3.96 4.00 6.01 6.02 10.10 10.10 16.15 15.87 30.09 2.00 2.38 1.48 100 1.524 2.032 3.30 4.41 4.45 6.69 6.70 11.23 11.24 17.96 17.67 33.47 2.22 2.66 1.66 120 1.829 2.438 3.98 5.32 5.36 8.05 8.06 13.50 13.51 21.57 21.28 40.24 2.68 3.20 2.00 150 2.286 3.048 4.99 6.67 6.72 10.09 10.10 16.91 16.92 26.98 26.70 50.39 3.36 4.02 2.53 200 3.048 4.064 6.68 8.93 8.99 13.49 13.50 22.59 22.59 36.01 35.73 67.31 4.50 5.39 3.40 250 3.810 5.080 8.37 11.18 11.25 16.89 16.90 28.27 28.27 45.04 44.76 84.23 5.64 6.76 4.27 300 4.572 6.096 10.06 13.44 13.52 20.29 20.30 33.94 33.95 54.07 53.79 101.14 6.78 8.12 5.14 350 5.334 7.112 11.75 15.70 15.79 23.69 23.70 39.62 39.63 63.10 62.82 118.06 7.92 9.49 400 6.096 8.128 13.44 17.96 18.05 27.09 27.10 45.30 45.31 72.13 71.85 134.98 9.06 10.85 500 7.620 10.160 16.82 22.47 22.58 33.89 33.90 56.65 56.66 90.18 89.91 168.81 11.34 13.58 600 9.144 12.192 20.20 26.98 27.12 40.69 40.70 68.01 68.02 108.24 107.96 202.65 13.62 16.32

height

(SH)

Effective

width

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8 ET-D75LE6 ET-D75LE5

(SW)

1.6-2.2 : 1 2.2-3.3 : 1 3.3-5.6 : 1 5.6-8.9 : 1 8.8-16.5 : 1 1.1-1.3 : 1 0.8 : 1

Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Fixed

Fixed-focus

lens

*1: “Throw ratio” is the approximate measurement range of the screen width to the projection distance.

ENGLISH

– 23

Installation (continued)

Projection distances by the type of projection lenses (for PT-D12000E)



For the screen aspect ratio of 4:3 (Units: m)

Lens type Zoom lens

Model number of

projection lens

Throw ratio

Screen dimensions Projection distance (L)

Screen

Effective

size

(inch)

70 1.067 1.422 2.07 2.77 2.80 4.21 4.23 7.09 7.10 11.37 11.09 21.14 1.39 1.66 1.02 80 1.219 1.626 2.38 3.18 3.21 4.83 4.84 8.13 8.13 13.01 12.73 24.21 1.60 1.91 1.18

90 1.372 1.829 2.68 3.59 3.62 5.45 5.46 9.16 9.16 14.65 14.37 27.29 1.81 2.16 1.34 100 1.524 2.032 2.99 4.00 4.04 6.07 6.08 10.19 10.19 16.29 16.01 30.36 2.01 2.41 1.50 120 1.829 2.438 3.60 4.82 4.86 7.30 7.31 12.25 12.26 19.57 19.29 36.50 2.43 2.90 1.81 150 2.286 3.048 4.53 6.05 6.09 9.15 9.16 15.34 15.35 24.49 24.21 45.72 3.05 3.65 2.29 200 3.048 4.064 6.06 8.10 8.15 12.24 12.25 20.50 20.50 32.69 32.40 61.08 4.08 4.89 3.08 250 3.810 5.080 7.59 10.15 10.21 15.33 15.34 25.65 25.66 40.88 40.60 76.44 5.12 6.13 3.87 300 4.572 6.096 9.13 12.19 12.27 18.41 18.42 30.81 30.81 49.08 48.80 91.79 6.15 7.37 4.66 350 5.334 7.112 10.66 14.24 14.32 21.50 21.51 35.96 35.97 57.28 57.00 107.15 7.19 8.61 400 6.096 8.128 12.19 16.29 16.38 24.58 24.60 41.12 41.12 65.47 65.19 122.51 8.22 9.85 500 7.620 10.160 15.26 20.39 20.50 30.76 30.77 51.42 51.43 81.87 81.59 153.23 10.29 12.33 600 9.144 12.192 18.33 24.49 24.61 36.93 36.94 61.73 61.74 98.26 97.98 183.95 12.36 14.81

height

(SH)

Effective

width

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8 ET-D75LE6 ET-D75LE5

(SW)

1.5-2.0 : 1 2.0-3.0 : 1 3.0-5.0 : 1 5.0-8.0 : 1 7.9-15.0 : 1 1.0-1.2 : 1 0.8 : 1

Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Fixed

Fixed-focus

lens

For the screen aspect ratio of 16:9 (Units: m)

Lens type Zoom lens

Model number of

projection lens

Throw ratio

Screen dimensions Projection distance (L)

Screen

Effective

size

(inch)

70 0.872 1.550 2.26 3.02 3.06 4.60 4.61 7.74 7.75 12.40 12.12 23.06 1.52 1.82 1.12

80 0.996 1.771 2.60 3.47 3.51 5.27 5.28 8.86 8.87 14.18 13.90 26.41 1.75 2.09 1.29

90 1.121 1.992 2.93 3.92 3.95 5.95 5.96 9.99 9.99 15.97 15.69 29.76 1.97 2.36 1.47 100 1.245 2.214 3.27 4.36 4.40 6.62 6.63 11.11 11.11 17.76 17.47 33.10 2.20 2.63 1.64 120 1.494 2.657 3.93 5.26 5.30 7.96 7.97 13.35 13.36 21.33 21.04 39.79 2.65 3.17 1.98 150 1.868 3.321 4.94 6.60 6.64 9.98 9.99 16.72 16.73 26.68 26.40 49.83 3.33 3.98 2.50 200 2.491 4.428 6.61 8.83 8.89 13.34 13.35 22.34 22.34 35.61 35.33 66.56 4.45 5.33 3.36 250 3.113 5.535 8.28 11.06 11.13 16.70 16.71 27.95 27.96 44.54 44.26 83.29 5.58 6.68 4.22 300 3.736 6.641 9.95 13.29 13.37 20.07 20.08 33.57 33.57 53.47 53.19 100.02 6.71 8.03 5.08 350 4.358 7.748 11.62 15.52 15.61 23.43 23.44 39.18 39.19 62.40 62.12 116.75 7.84 9.38 400 4.981 8.855 13.29 17.76 17.85 26.79 26.80 44.80 44.80 71.33 71.05 133.48 8.96 10.73 500 6.226 11.069 16.63 22.22 22.33 33.51 33.52 56.03 56.03 89.19 88.91 166.95 11.22 13.43 600 7.472 13.283 19.97 26.69 26.82 40.24 40.25 67.26 67.26 107.04 106.77 200.41 13.47 16.14

height

(SH)

Effective

width

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8 ET-D75LE6 ET-D75LE5

(SW)

1.5-2.0 : 1 2.0-3.0 : 1 3.0-5.0 : 1 5.0-8.0 : 1 8.0-15.0 : 1 1.0-1.2 : 1 0.8 : 1

Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Fixed

Fixed-focus

lens

24 –

*1: “Throw ratio” is the approximate measurement range of the screen width to the projection distance.

ENGLISH

If the projector is used with a screen size not listed in this manual, check the diagonal dimension (inch) of your screen and calculate the projection distance using the following formulas.

Calculation formulas for projection distance by lens types



(for PT-DZ12000E)

Model number of

projection lens

ET-D75LE1

ET-D75LE2

ET-D75LE3

Zoom lens

Throw ratio Aspect ratio Projection distance (L) formula (Units: m)

1.4-1.8 : 1 16:10

1.4-1.8 : 1 16:9

1.6-2.2 : 1 4:3

1.8-2.8 : 1 16:10

1.8-2.8 : 1 16:9

2.2-3.3 : 1 4:3

2.8-4.6 : 1 16:10

2.8-4.6 : 1 16:9

3.3-5.6 : 1 4:3

4.6-7.4 : 1 16:10

Minimal distance : L = 0.0298 × Screen diagonal (inch) – 0.0760 Maximal distance: L = 0.0399 × Screen diagonal (inch) – 0.1004

Minimal distance : L = 0.0307 × Screen diagonal (inch) – 0.0760 Maximal distance: L = 0.0410 × Screen diagonal (inch) – 0.1004

Minimal distance : L = 0.0338 × Screen diagonal (inch) – 0.0760 Maximal distance: L = 0.0451 × Screen diagonal (inch) – 0.1004

Minimal distance : L = 0.0400 × Screen diagonal (inch) – 0.0795 Maximal distance: L = 0.0601 × Screen diagonal (inch) – 0.1064

Minimal distance : L = 0.0412 × Screen diagonal (inch) – 0.0795 Maximal distance: L = 0.0617 × Screen diagonal (inch) – 0.1064

Minimal distance : L = 0.0453 × Screen diagonal (inch) – 0.0795 Maximal distance: L = 0.0680 × Screen diagonal (inch) – 0.1064

Minimal distance : L = 0.0601 × Screen diagonal (inch) – 0.0958 Maximal distance: L = 0.1003 × Screen diagonal (inch) – 0.1216

Minimal distance : L = 0.0617 × Screen diagonal (inch) – 0.0958 Maximal distance: L = 0.1031 × Screen diagonal (inch) – 0.1216

Minimal distance : L = 0.0680 × Screen diagonal (inch) – 0.0958 Maximal distance: L = 0.1136 × Screen diagonal (inch) – 0.1216

Minimal distance : L = 0.1003 × Screen diagonal (inch) – 0.1158 Maximal distance: L = 0.1595 × Screen diagonal (inch) – 0.1013

Getting Started

ET-D75LE4

ET-D75LE8

ET-D75LE6

ET-D75LE5

Fixed-focus lens

4.6-7.4 : 1 16:9

5.6-8.9 : 1 4:3

7.3-13.8 : 1 16:10

7.3-13.8 : 1 16:9

8.8-16.5 : 1 4:3

0.9-1.1 : 1 16:10

0.9-1.1 : 1 16:9

1.1-1.3 : 1 4:3

0.7 : 1 16:10 L = 0.0154 × Screen diagonal (inch) – 0.0835

0.7 : 1 16:9 L = 0.0158 × Screen diagonal (inch) – 0.0835

0.8 : 1 4:3 L = 0.0174 × Screen diagonal (inch) – 0.0835

Minimal distance : L = 0.1031 × Screen diagonal (inch) – 0.1158 Maximal distance: L = 0.1639 × Screen diagonal (inch) – 0.1013

Minimal distance : L = 0.1136 × Screen diagonal (inch) – 0.1158 Maximal distance: L = 0.1806 × Screen diagonal (inch) – 0.1013

Minimal distance : L = 0.1595 × Screen diagonal (inch) – 0.3862 Maximal distance: L = 0.2989 × Screen diagonal (inch) – 0.3598

Minimal distance : L = 0.1640 × Screen diagonal (inch) – 0.3862 Maximal distance: L = 0.3072 × Screen diagonal (inch) – 0.3598

Minimal distance : L = 0.1806 × Screen diagonal (inch) – 0.3862 Maximal distance: L = 0.3383 × Screen diagonal (inch) – 0.3598

Minimal distance : L = 0.0201 × Screen diagonal (inch) – 0.0566 Maximal distance: L = 0.0241 × Screen diagonal (inch) – 0.0736

Minimal distance : L = 0.0207 × Screen diagonal (inch) – 0.0566 Maximal distance: L = 0.0248 × Screen diagonal (inch) – 0.0736

Minimal distance : L = 0.0228 × Screen diagonal (inch) – 0.0566 Maximal distance: L = 0.0273 × Screen diagonal (inch) – 0.0736

ENGLISH

– 25

Installation (continued)

50 cm or more

10 cm or more

50 cm or more

40 cm or more

+15°

Calculation formulas for projection distance by lens types (for PT-D12000E)



Model number of

projection lens

ET-D75LE1 1.5-2.0 : 1

ET-D75LE2 2.0-3.0 : 1

ET-D75LE3 3.0-5.0 : 1

Zoom lens

ET-D75LE4 5.0-8.0 : 1

ET-D75LE8

ET-D75LE6 1.0-1.2 : 1

ET-D75LE5 0.8 : 1

lens

focus

Fixed-

Throw ratio Aspect ratio Projection distance (L) formula (Units: m)

4:3

16:9

4:3

16:9

4:3

16:9

4:3

16:9

7.9-15.0 : 1 4:3

8.0-15.0 : 1 16:9

4:3

16:9

4:3 L = 0.0158 × Screen diagonal (inch) – 0.0835

16:9 L = 0.0172 × Screen diagonal (inch) – 0.0835

Minimal distance : L = 0.0307 × Screen diagonal (inch) – 0.0760 Maximal distance: L = 0.0410 × Screen diagonal (inch) – 0.1004 Minimal distance : L = 0.0334 × Screen diagonal (inch) – 0.0760 Maximal distance: L = 0.0446 × Screen diagonal (inch) – 0.1004 Minimal distance : L = 0.0412 × Screen diagonal (inch) – 0.0795 Maximal distance: L = 0.0617 × Screen diagonal (inch) – 0.1064 Minimal distance : L = 0.0448 × Screen diagonal (inch) – 0.0795 Maximal distance: L = 0.0672 × Screen diagonal (inch) – 0.1064 Minimal distance : L = 0.0617 × Screen diagonal (inch) – 0.0958 Maximal distance: L = 0.1031 × Screen diagonal (inch) – 0.1216 Minimal distance : L = 0.0672 × Screen diagonal (inch) – 0.0958 Maximal distance: L = 0.1123 × Screen diagonal (inch) – 0.1216 Minimal distance : L = 0.1031 × Screen diagonal (inch) – 0.1158 Maximal distance: L = 0.1639 × Screen diagonal (inch) – 0.1013 Minimal distance : L = 0.1123 × Screen diagonal (inch) – 0.1158 Maximal distance: L = 0.1786 × Screen diagonal (inch) – 0.1013 Minimal distance : L = 0.1640 × Screen diagonal (inch) – 0.3862 Maximal distance: L = 0.3072 × Screen diagonal (inch) – 0.3598 Minimal distance : L = 0.1786 × Screen diagonal (inch) – 0.3862 Maximal distance: L = 0.3346 × Screen diagonal (inch) – 0.3598 Minimal distance : L = 0.0207 × Screen diagonal (inch) – 0.0566 Maximal distance: L = 0.0248 × Screen diagonal (inch) – 0.0736 Minimal distance : L = 0.0225 × Screen diagonal (inch) – 0.0566 Maximal distance: L = 0.0270 × Screen diagonal (inch) – 0.0736

Installation dimensions diagram

Figure 1 : Dimensions applying when

one unit is used

50 cm or

Exhaust

30 cm or more

40 cm or more

30 cm or more

Attention

Leave a clearance of at least 50 cm so that the ventilation opening on the rear panel will not be blocked.• Set up the projector so that air can flow freely around the rear of the projector without staying still. In addition, • leave a space of 30 cm or more at the sides so that the hot air coming out from the air outlet vents does not get drawn in through the air intake vents. Set up the projector with a space of 40 cm or more at the front so that the air filter can be replaced.• When the projector is to be placed inside a box and used, ensure the structure has a duct or the like to • discharge air from the box, leave the clearances shown in Fig. 2, and ensure the temperature during operation remains within the 0 °C to 35 °C range.

Figure 2 : Dimensions applying when

two units are used)

50 cm

Exhaust

50 cm or more

Exhaust

or more

50 cm or more

40 cm or more

10 cm or more

Figure 3 : Set rotation direction

+15° +15°

OPEN

FILTER CLEANING

+15° +15°

26 –

ENGLISH

Connection

Before starting connection

Before connection, read carefully the instruction manual for the device to be connected.• Turning off the power switch of the devices before connecting cables.• If any connection cable is not supplied with the device, or if no optional cable is available for connection of the •

device, prepare a necessary system connection cable to suit the device. Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture. In •

this case, a time base corrector (TBC) must be connected. The projector accepts the following signals: video, S-Video, analogue RGB, DVI-D and signals which are •

compatible with the optional input module (p. 30). Some PC models cannot be connected to the projector.•

The pin-out and signal names of the S-VIDEO IN terminal are shown in the diagram below.

Pin No. Signal

Outside view

1 2 3 4

Ground (luminance signal) Ground (colour signal) Luminance signal Colour signal

Getting Started

The pin-out and signal names of the RGB2 IN terminal are shown in the diagram below.

Pin No. Signal

1 2 3 m n

Outside view

4, 9, l 5-8, j

The pin-out and signal names of the DVI-D IN terminal are shown in the diagram below.

,and o are not assigned.

and k are GND terminals.

Outside view

Pin No. Signal Pin No. Signal

1 2

4q 5r 6 7 8t 9 j k lx

R/P G/G • SYNC/Y

B/P HD/SYNC VD

T.M.D.S data 2– T.M.D.S data 2+

T.M.D.S data 2 / 4 shield

DDC clock DDC data

T.M.D.S data 1– T.M.D.S data 1+ T.M.D.S data 1 / 3 shield

m n o p

u v w

+5V Ground Hot plug detection T.M.D.S data 0T.M.D.S data 0+

T.M.D.S data 0 / 5 shield

T.M.D.S clock shield T.M.D.S clock+ T.M.D.S clock–

ENGLISH

– 27

Connection (continued)

Example of connecting with VIDEO devices

Video deck (TBC built-in)

G/YR/P

Control PC

SERIALREMOTE 1 REMOTE 2 IN

B/P

Control PC

IN OUT

OUT

VIDEO RGB 2 IN

S-VIDEO IN

RS-232C IN RS-422 IN

SYNC/HD VD

RGB 1 IN

RS-422 OUT

DVI-D IN

Control PC

LAN

Red (connected to PR terminal) Blue (connected to P

B terminal)

Green (connected to Y terminal)

Colour monitor Video deck (TBC built-in) DVD player

DVD player with HDMI (HDCP) terminal

Attention

When connecting with a video deck, be sure to use the one with a built-in time base corrector (TBC) or use a • TBC between the projector and the video deck.

If nonstandard burst signals are connected, the image may be distorted. If this is the case, connect a TBC • between the projector and the video deck.

Note

The DVI-D signal input terminal supports only a single link.• The HDMI-DVI-D conversion cable is required to connect an HDMI-compliant device.• When using the DVI-D input, EDID settings may be required for the connected device. (pp. 73, 74)• It is possible to connect the DVI-D input terminal with an HDMI- or DVI-D-compliant device, but with some •

devices the images may not appear or other problems may be encountered in operation.

28 –

ENGLISH

Example of connecting with personal computers

Control PC

IN OUT

OUT

VIDEO RGB 2 IN

S-VIDEO IN

RS-232C IN RS-422 IN

G/YR/P

SYNC/HD VD

RGB 1 IN

B/P

SERIALREMOTE 1 REMOTE 2 IN

Control PC

RS-422 OUT

DVI-D IN

LAN

To 2nd projector (SERIAL IN terminal)

Control PC

Getting Started

I/F

PC PC

Attention

When the main power of the main unit is turned off, also turn off the power of the PC.• When the length of the cable from a PC to the projector is long or when there are many relay devices such as •

switches, the video may be interrupted or fuzzy. In such a case, use a cable compensator.

Note

For the specifications of the RGB signals that can be applied from the PC, see the data sheet on pages • 122-123.

If your PC has the resume feature (last memory), the computer may not function properly until the resume • capability is disabled.

When using the DVI-D input, EDID settings may be required for the connected device. (pp. 73, 74)•

ENGLISH

– 29

Installation of input module (optional)

Installing the input module

Types of the input modules (optional)



Prepare beforehand an input module (optional) compatible with the input signals of the system.

Module

SD-SDI input module

HD/SD-SDI input module

Module model

No.

ET-MD77SD1

ET-MD77SD3

ET-MD100SD4 BNC input × 2

Terminal Signal formats supported

BNC input × 1 BNC output × 1

RJ-45 input × 1

BNC input × 1 BNC output × 1

RJ-45 input × 1

SMPTE259M compliant : 480i, 576i

10BASE-T/100BASE-TX

SMPTE259M compliant : 480i, 576i SMPTE292M compliant :

720/60p, 720/59.94p, 720/50p 1 035/60i, 1 035/59.94i, 1 080/60i, 1 080/59.94i 1 080/50i, 1 080/24sF, 1 080/23.98sF, 1 080/30p 1 080/29.97p, 1 080/25p, 1 080/24p, 1 080/23.98p

10BASE-T/100BASE-TX

Single link SD-SDI Signal : 480i, 576i Single link HD-SDI Signal (YP

720/60p, 720/59.94p, 720/50p, 1 080/60i, 1 080/59.94i, 1 080/50i, 1 080/24sF, 1 080/23.98sF, 1 080/30p, 1 080/29.97p, 1 080/25p, 1 080/24p, 1 080/23.98p

Dual link HD-SDI signal (RGB 4:4:4) :

1 920 × 1 080/50i, 1 920 × 1 080/59.94i, 1 920 × 1 080/60i, 1 920 × 1 080/23.98p, 1 920 × 1 080/23.98sF, 1 920 × 1 080/25p, 1 920 × 1 080/24p, 1 920 × 1 080/24sF, 1 920 × 1 080/29.97p, 1 920 × 1 080/30p

Dual link HD-SDI signal (X’ Y’ Z’ 4:4:4) :

2 048 × 1 080/23.98p, 2 048 × 1 080/23.98sF, 2 048 × 1 080/24p, 2 048 × 1 080/24sF

BPR 4:2:2) :

DVI-D single link, DVI 1.0 compliant

(non-interlace)

DVI-D input module

ET-MD77DV

DVI-D 24p input × 1

RJ-45 input × 1

HDCP-compliant

480p, 576p, 720/60p, 720/59.94p, 720/50p 1 080/60i, 1 080/59.94i, 1 080/50i、1 080/24sF, 1 080/23.98sF 1 080/30p, 1 080/29.97p, 1 080/25p, 1 080/24p, 1 080/23.98p 1 080/60p, 1 080/59.94p, 1 080/50p Displayable resolution VGA - WUXGA Dot clock frequency 25 - 162 MHz

10BASE-T/100BASE-TX

*1: The LAN terminal of the input module (optional) cannot be used with the PT-D12000E/PT-DZ12000E. Use the

LAN terminal that is provided as standard with the projector.

*2: HDCP (High-bandwidth Digital Content Protection)

HDCP is a specification for encoding digital image signals which was developed to protect digital content. The DVI-D/HDMI output signals from the HDCP-compliant equipment have been encoded by the HDCP specifications to ensure content protection, but the DVI-D input module is capable of displaying the digital images properly since it complies with the HDCP specification.

*3: The WUXGA signals support only VESA CVT-RB (Reduced Blanking) signals.

30 –

ENGLISH

Procedure of installation



Disconnect the power before installing the input module.

MENU LENS

LAN

POWER ON STANDBY

VIDEO

ENTER

S-VIDEO

RGB1

AUTO

SHUTTER

SETUP

RGB2

LIGHT

DVI-D

AUX

OFF

Getting Started

OFF ON

AC IN

MAIN POWER

IN OUT

RS-232C IN RS-422 IN RS-422 OUT

REMOTE 1 REMOTE 2 IN

G/YR/P

SYNC/HD VD

OUT

S-VIDEO IN

VIDEO RGB 2 IN

RGB 1 IN

Slot Cover

SERIAL

B/P

DVI-D IN

Remove the slot cover.1.

Remove 2 screws.

Insert the input module.2.

Fix the input module.3.

This projector needs to register the type of input • signal after the installation of the input module.

For details on the registration of the input • signals, refer to pages 45-47.

Slot

Input module

Tighten the two screws.

ENGLISH

– 31

Installation of input module (optional) (continued)

Connecting signals to the input module

When installing the projector, it is necessary to connect signals to the input module in accordance with the connecting equipment. Refer to the following diagram to establish proper signal connection.

SD-SDI input module

ET-MD77SD1

Business digital

VCR

DVD player

High-vision

video deck

SDI signal

DVI-D signal

HD/SD-SDI input module

ET-MD77SD3

Dual link HD/SD-SDI input module

ET-MD100SD4

DVI-D input module

ET-MD77DV

OFF ON

AC IN

IN OUT

REMOTE 1 REMOTE 2 IN

OUT

S-VIDEO IN

VIDEO RGB 2 IN

MAIN POWER

Projector

RS-232C IN RS-422 IN RS-422 OUT

SERIAL

B/P

G/YR/P

SYNC/HD VD

DVI-D IN

RGB 1 IN

MENU LENS

LAN

POWER ON STANDBY

VIDEO

ENTER

S-VIDEO

RGB1

AUTO

SHUTTER

SETUP

RGB2

LIGHT

DVI-D

AUX

OFF

Note

Insert the input module suitable for the input signal specifications.• Normally, use SYSTEM SELECTOR in “AUTO”. (pp. 58-59)•

32 –

ENGLISH

Connecting the signal to the SD-SDI input module

SD-SDI input module (optional)

ET-MD77SD1 (for 480i/576i)

SD-SDI Module ET-MD77SD1

SERIAL

OUT

LAN

LAN terminal

(10BASE-T/100BASE-TX)

SD-SDI signal SD-SDI signal output

(active through)

Business digital

VCR

Note

If a source with an unstable signal is connected, errors in automatic signal recognition may occur. If this • happens, use the SYSTEM SELECTOR menu to switch the format to the one which matches the signals being input.

You can switch the input format mode from the SYSTEM SELECTOR menu. (pp. 58-59)•

*1: The LAN terminal of the input module (optional) cannot be used with the PT-D12000E/PT-DZ12000E. Use the

LAN terminal that is provided as standard with the projector.

Connecting the signal to the HD/SD-SDI input module

HD/SD-SDI input module (optional)

ET-MD77SD3 (for HD/SD)

HD/SD-SDI Module ET-MD77SD3

SERIAL

OUT

LAN

Getting Started

LAN terminal

(10BASE-T/100BASE-TX)

HD-SDI or SD-SDI

signal

HD-SDI or SD-SDI

signal output

(active through)

Business digital

VCR

Note

You can switch the input format mode from the SYSTEM SELECTOR menu. (pp. 58-59)• If a source with an unstable signal is connected, errors in automatic signal recognition may occur. If this •

happens, use the SYSTEM SELECTOR menu to switch the format to the one which matches the signals being input.

To ensure full imaging performance, use a connecting cable with the specifications of 5CFB or higher, or of • Belden1694A or higher. (For example: 5CFB, 5CFTX, 7CFB, Belden1694A, etc.)

*1: The LAN terminal of the input module (optional) cannot be used with the PT-D12000E/PT-DZ12000E. Use the

LAN terminal that is provided as standard with the projector.

ENGLISH

– 33

Installation of input module (optional) (continued)

Connecting the signal to the dual link HD/SD-SDI input module

Dual link HD/SD-SDI input module (optional)

ET-MD100SD4

Dual Link HD-SDI Module ET-MD100SD4

HD-SDI or

SD-SDI signal

LINK-A

SERIAL IN

LINK-B

Business digital

VCR

When connecting a single link signal, connect to the LINK-A terminal.• When connecting a dual link signal, connect to both the LINK-A and LINK-B terminals.•

Note

You can switch the input format mode from the SYSTEM SELECTOR menu. (pp. 58-59)• Settings specific to the connected device are required. (pp. 74-75)• To send the pictures properly, use a connecting cable with the specifications of 5CFB or higher (5CFB, 7CFB, •

etc.) or of Belden1694A or higher. Also, use a cable that is shorter than 100 m. Make sure that the cables used to link LINK-A terminal and LINK-B terminal are of the same type and length. •

If there is a difference in length greater than 4 m between the two cables, the images will not be projected correctly.

When connecting to dual link signals, connect directly to the signal output device without connecting through a • distributor or other such device. A phase difference may occur between the LINK-A signal and LINK-B signal, which may prevent the image from being correctly projected.

If the connected signal is unstable, the automatic distinction function may not operate correctly. In this case, • switch to a mode that better suits the signal format from the SYSTEM SELECTOR menu.

34 –

ENGLISH

Connecting signals to the DVI-D input module

DVI-D input module (optional)

ET-MD77DV

DVI Module ET-MD77DV

DVI-D signal LAN terminal

PC with DVI output

Pin assignments and signal names of DVI-D input • terminal are listed in the table at right.

Outside view

DVI-D IN LAN

(10BASE-T/100BASE-TX)

DVD player or high-vision

video deck equipped with

DVD/HDMI terminal

Pin No.

T.M.D.S data 2–

T.M.D.S data 2+ T.M.D.S data 2 / 4

shield

4q 5r 6

DDC clock

DDC data

8t 9

T.M.D.S data 1–

T.M.D.S data 1+ T.M.D.S data 1 / 3

shield

Signal

Pin No.

m n

+5V

Ground

Hot plug detection T.M.D.S data 0T.M.D.S data 0+ T.M.D.S data 0 / 5

shield

u v

T.M.D.S clock shield

T.M.D.S clock+

T.M.D.S clock–

Getting Started

Signal

Note

The DVI-D signal input module supports only a single link.• The HDMI-DVI-D conversion cable is required to connect an HDMI-compliant device.• When using the DVI-D input, EDID settings may be required for the connected device. (pp. 73, 74)• It is possible to connect the DVI-D input module with an HDMI- or DVI-D-compliant device, but with some •

devices the images may not appear or other problems may be encountered in operation.

*1: The LAN terminal of the input module (optional) cannot be used with the PT-D12000E/PT-DZ12000E. Use the

LAN terminal that is provided as standard with the projector.

ENGLISH

– 35

How to install and remove the projection lens (optional)

Adjust the lens shift position so that it is at the home position (p. 41) before installing or removing the projection lens.

Attention

Remove the dust-proof sponge from the lens fitting • of the projector before installing the projection lens. (Keep the dust-proof sponge in a safe place for later use if needed.)

After removing the projection lens, install the dust-• proof sponge to the lens fitting of the projector in order to stop dust from getting inside the projector.

How to install the projection lens

While pressing the projection 1. lens cover lock button, pull the cover forward to remove it.

Push the projection lens cover in 3. until it clicks into place.

How to remove the projection lens

While pressing the projection 1. lens cover lock button, pull the cover forward to remove it.

OPEN

FILTER CLEANING

Projection lens cover lock button

Align the mark (orange) on 2. the projection lens with the mark on the projector (

), and then insert the lens and turn it clockwise until it clicks into place.

OPEN

FILTER CLEANING

Projection lens cover lock button

While holding down the 2. projection lens lock button, turn the projection lens counter clockwise, and then pull it off.

Projection lens lock button

36 –

Mark (orange)

ENGLISH

Projection

Power indicator lamp

OPEN

FILTER CLEANING

Lock Button

Power indicator lamp

This shows the power supply status. Make sure that you fully understand the operation of the power indicator lamp before operating the projector.

Indicator

status

Off Main power is off

Standby mode

Red Lit

Green Lit Images are being projected (on)

Orange Lit

POWER ON ( | ) button can be pressed so that images can be projected.

Cooling mode After a short while, the projector will switch to standby mode.

Attention

While the projector is in cooling mode (when the • power indicator lamp is lit orange), the internal fan is running to cool down the projector. Do not turn off the MAIN POWER switch or disconnect the power cord at this time.

Projector status

Connecting the power cord

Insert the accessory power cord securely into the projector and the electrical outlet. Be sure to read the “IMPORTANT SAFETY NOTICE” (pp. 4-5) and “Precautions with regard to safety” (pp. 6-9) for details on handling the power cord.

Installation



Check the shape of the AC 1. IN terminal on the side of the projector and the shape of the power cord connector, and insert the power cord securely into the AC IN terminal.

Insert the power cord plug into 2. an electrical outlet.

Removal



Basic Operation

Note

If the POWER ON “ | ” button is pressed while • the projector is still in cooling mode, it may take some time before the projector is ready to project pictures.

Check that the MAIN POWER 1. switch on the projector is at the OFF “○” position, and then disconnect the power cord plug from the electrical outlet.

Remove the power cord from the 2. AC IN terminal while pressing the lock button on the power cord connector.

Attention

Connect all peripheral equipment to the projector • before connecting the projector’s power cord. (pp. 28-29)

ENGLISH

– 37

Projection (continued)

12 7

Powering up the projector

Connect the supplied power

cable. (220 V-240 V, 50 Hz/60 Hz)

Press the “ | ” marked side of the

MAIN POWER switch to turn on the power.

The power indicator lamp on the projector will • flash in red. After a short period, the indicator will illuminate and the projector will enter standby mode.

Press POWER ON “ | ”.

The power indicator lamp illuminates in green • and soon the image is projected on the screen.

Note

If the projector is powered up at about 0 °C, a • warm-up period of approximately 5 minutes may be necessary to start projection. The temperature monitor (TEMP) lamp lights up during the warm-up period. When the warm-up is completed, the temperature monitor (TEMP) lamp turns off and the image is projected on the screen.

If the temperature of the operating environment is • low and warm-up takes more than 5 minutes, the projector will judge that a problem has occurred and the power will be turned off automatically. If this happens, increase the temperature around the projector so that it is 0 °C or higher, and then turn on the MAIN POWER switch and the POWER ON “ | ” switch once more.

63 5

Making adjustment and selection

Roughly adjust the focus of the

lens. (p. 40)

Select and set the projection

scheme. (p. 78)

Select the input signal by

pressing the input selector button to toggle through RGB1, RGB2, DVI-D, VIDEO, S-VIDEO and AUX. (p. 48)

The AUX button is disabled when an optional • input module is not connected.

Adjust the tilt of the main unit in

front and rear or right and left. (p. 20)

Adjust the shift. (p. 40)

Press AUTO SETUP if the input

signal is RGB signal. (p. 49)

Fit the image size to the screen

size. (p. 40)

Adjust the focus. (p. 40)

4, 8-l

4, k

8 j

38 –

ENGLISH

Readjust the zoom so that the

image size fits in the screen. (p. 40)

Powering off the projector

Press POWER STANDBY “

A confirmation screen will appear.•

POWER OFF

OK CANCEL

CHANGE

ENTER

EXECUTE

Press ◄ or ► to select “OK” and

press ENTER. (or press POWER STANDBY “ again.)

The projection of the image stops, and the • power indicator lamp of the main unit lights up orange. (The cooling fan keeps running.)

Wait until the power indicator

lamp of the main unit turns to red (i.e., until the cooling fan stops). (Approx. 3 minutes)

While the cooling fan is still running, never turn • off the MAIN POWER switch, nor unplug the projector from the outlet.

”.

”

Note

In the cooling state after the power is turned off, the • lamp will not light up even if the power is turned on. To light up the lamp, turn on the power supply again when the lamp has been cooled sufficiently.

The projector consumes approximately 15 W of • power even in standby mode. (Power indicator lamp lit in red)

If the main power is mistakenly turned off during • use, the lamp may not light up if the power supply is turned on after turning on the main power. Please turn the main power on again after a while.

Be sure to set the date and time when the projector is turned on for the first time after being purchased. For details, refer to “Setting the date and time” on page 83.

Basic Operation

Press the “○” marked side of the

MAIN POWER switch to remove all power from the projector.

ENGLISH

– 39

How to adjust the lens

How to adjust the focus, zoom and shift

If the focusing, zooming or positioning of the image projected on the screen is not successful, even though the projector is properly positioned against the screen, you can adjust the focus, the zoom, or the vertical or horizontal position of the image.

At the projector



LENS FOCUS

ADJUST

LENS

ZOOM ADJUST

LENS

SHIFT ADJUST

LENS FOCUS

ADJUST

LENS

ZOOM ADJUST

LENS

SHIFT ADJUST

Press LENS on the control panel 1. of the main unit.

Pressing the button changes the setup • screen in the order of “FOCUS”, “ZOOM” and “SHIFT”.

Press ▲▼◄► to select an item 2. and adjust it.

Using the remote control



Press LENS (FOCUS, ZOOM, 1. SHIFT) on the remote control.

When the FOCUS button is pressed:•

The focus is adjusted. When the ZOOM button is pressed:•

The zoom is adjusted.

When the SHIFT button is pressed: •

The shift is adjusted.

Press ▲▼◄► to select an item 2. and adjust it.

CAUTION:

Be careful not to catch your fingers between the lens and shroud when shifting the lens.

Note

Only “FOCUS” is displayed with the background colours set with OSD DESIGN, to distinguish the displayed • adjustment menu by colour, even if the characters cannot be read and look out of focus. (p. 75)

The zoom adjustment menu will be displayed only when a lens with zoom function is being used.•

40 –

ENGLISH

Adjustment range after lens position (optical shift)

Do not move the lens beyond the bounds of the shift range as this may cause a change in the focus. This limitation is to protect the parts of the projector. Using the standard projection position as the reference, the optical axis shift function makes it possible to adjust the projection position in the ranges shown in the figures below.

Model number of

projection lens

ET-D75LE6

Zoom Lens

ET-D75LE1 ET-D75LE2 ET-D75LE3 ET-D75LE4 ET-D75LE8

Projected

screen height, V

0.12V 0.12V

Projected

screen height, V

0.1V 0.1V

PT-D12000E PT-DZ12000E

0.2H 0.2H

Projected screen

width, H

0.3H 0.3H

Projected screen

width, H

0.40V0.40V

Standard projection position

0.12V 0.12V

0.50V0.50V

Standard projection position

0.1V 0.1V

Projected

screen height, V

0.12V 0.12V

Projected

screen height, V

0.12V 0.12V

0.15H 0.15H

Projected screen

width, H

0.2H 0.2H

Projected screen

width, H

0.12V

0.44V

Standard projection position

0.44V

0.12V

0.55V

Standard projection position

0.55V

0.12V

Basic Operation

Note

The ET-D75LE5 has a fixed focal point, and so shift adjustment cannot be carried out.•

Moving the projection lens position to the home position

Press and hold LENS on the projector’s controls or SHIFT on the remote 1. control for 3 seconds or more.

LENS

SHIFT

ENTER

EXECUTE

CANCEL

Press ENTER while the menu shown above is being displayed. (It will be 2. displayed for about 5 seconds.)

“PROGRESS...” will appear in the menu, and the projection lens will move to the home position.•

Note

The home position for the projection lens is the lens position when the lens is being replaced or when the • projector is being stored away, and it is not the optical centre of the screen.

ENGLISH

– 41

How to adjust the lens (continued)

How to adjust the lens mounter for addressing unevenness of focusing

About the focus balance



Relation between the orientation of the lens and focus surface on the screen side z

If the projection lens is tilted in relation to the surface on which the images are formed, and the front (screen side) of the projection lens points downward (direction of broken arrow line) as shown in the example in the figure 1, the focus surface on the screen side is tilted so that its top is at the back of the screen and its bottom is in front of the screen.

Figure 1: Illustration of influence of lens orientation

Projection lens

Image formation surface

Focus surface on screen side

Procedure for adjusting the focus balance (adjusting the tilt with the lens mounter)



There are focus adjustment screws in three places on the lens mounter of the projector that can be used as a correction function when evenness of the whole screen cannot be obtained even after adjusting the lens focus.

Structure of lens mounter (Figure 2, Figure 3) z

Turning the focus adjustment screws in three places on the lens mounter has the effect of moving the lens slightly forward or backward. Furthermore, tightening the fixing screws in three places locks the lens bracket to stop it from moving.

Figure 2 : Front view of lens mounter (when viewed from screen side)

Fixing screwsLens bracket

(Adjust the focus adjustment screws a, b and c after installing the lens.)

42 –

Figure 3 : Cross-section view of lens mounter part

Lens tilt direction (when adjustment screws turned counterclockwise)

Lens bracket Adjustment

Hole for Allen hex socket driver Spring

ENGLISH

Screen direction

LensFixing screws

screw

If the lens is heavy or the projector is installed so that it is tilted, the lens may be tilted, resulting in the focus becoming unbalanced. In such a case, refer to the figure 4 and table below, and follow the procedure below to perform adjustment.

Adjustment procedure z

Switch to the focus adjustment mode with the remote control, and use the ▼ button to first offset the

whole focus.

Use the ▲ button to stop at the place that first becomes just in focus in any of the directions of the

screen. (In this state, the just-in-focus point is at the back of the screen in the direction in which the focus is offset.)

Remove the lens cover and lens.

Loosen by two turns the fixing screw of the direction that is opposite the direction in which the focus

is most offset (direction in which the just-in-focus point in 2 is the most offset toward the back) (see Figure 4).

Attention

Be careful because turning a screw more than twice to loosen it will result in the spring becoming detached • and the projector needing to be repaired. Make adjustments in up to two places, and fully turn the screw clockwise in at least one place.•

Install the removed lens.

Turn the adjustment screw counterclockwise little by little and stop at the point that is in focus. Turning

the screw counterclockwise moves the lens bracket of the mounter forward (screen side), which changes the tilt of the lens (see Figure 1) and moves the focus point in the projection image on the screen in the opposite direction to that of the adjustment screw.

Changing the tilt of the lens also changes the screen position of the projection image with regards to

the screen surface, so use the remote control to switch to the lens shift adjustment mode and return the position to the optimal position.

Perform refocus adjustment around the centre of the screen, and make even finer adjustments of the

rotation amount of the adjustment screws if the focus is still inadequate.

When adjustment is complete, remove the lens and then tighten the loosened fixing screws.

Install the lens and cover again to complete the focus adjustment.

Basic Operation

Tool to be used: Allen hex socket driver or Allen wrench (2.5 mm diagonal hexagon) An Allen wrench is supplied with the ET-D75LE6 and ET-D75LE8 optional lens.

Figure 4 : Relation between the adjustment place and adjustment screw

H left

c+(a) b+(a)

ac ab

Screen

Adjustment place: The place where the just-in-focus point is at the back.

When optimal focus point is

at front of screen for V up

V up

b+c

V bottom

Turn counterclockwise

right

Projector

When optimal focus is at

front of screen for V bottom

Turn counterclockwise Turn counterclockwise

When optimal focus is at

front of screen for H left

When optimal focus is at

front of screen for H right

Turn counterclockwise Turn counterclockwise

ENGLISH

– 43

How to adjust the lens (continued)

Precautions for projector installation work z

When installing and using the projector with a method other than floor standing installation using the adjustable feet, insert, for example, spacers (metal) between the projector and installation surface so that there is a gap of about 10 mm to 20 mm to ensure the cabinet does not touch the installation surface. Furthermore, use the screw holes (shown in the figure) for ceiling mounting to fix the projector in place. (Screw diameter: M6, set inside screw length: 8 mm) Note that if the cabinet is touching the installation surface when used, it may take a while until the images stabilize after the power is turned on.

Ceiling mounting screws (M6)

Base

Spacers

Gap (10 mm to 20 mm) Make sure air can circulate

around the air intake vent. Failure to do so may result in the projector not operating properly.

44 –

ENGLISH

Registration of input signal data

Registration of new data

When a new signal is supplied, press MENU on the remote control or operating section of the main unit. When its data has been registered, the “MAIN MENU” screen is displayed.

Note

▲▼◄►

ENTER

DEFAULT

The data of 96 input signals can be registered.• The signals supporting the installed input module •

are input and their data registered. The memories are numbered over 12 pages (A to L: •

8 data items can be registered on each page), and the data is registered in the unused memory with the lowest number. If all the memories are used, the data of the old signals is overwritten in sequence.

The names of the registered data are automatically • determined by the input signals and memory numbers.

If a menu is being displayed, the new signals will be • registered at the instant they are input.

The input signal data must be registered because it is not registered on shipment of the projector.

Press to display the MAIN MENU screen.

Press to select “SIGNAL LIST”.

Press to display the “REGISTERED SIGNAL LIST” menu.

The memories extend • over 12 pages (A to L with 8 data items each, giving a total of 96 memories).

MAIN MENU PICTURE

POSITION ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION

PROJECTOR SETUP

P IN P TEST PATTERN SIGNAL LIST SECURITY NETWORK

Renaming the registered signals

Press ▲▼◄ ► to select the 1. signal whose details are to be displayed.

REGISTERED SIGNAL LIST

A1:SVGA72-A1 RGB1 −−−

A2:SVGA72-A2 RGB1 −−−

A3:SVGA72-A3 RGB1 −−−

Press ENTER.2.

The “REGISTERED SIGNAL STATUS” screen • will be displayed.

REGISTERED SIGNAL STATUS

NAME MEMORY NO INPUT fH fV SYNC.STATE

The data items including the input signal name, • memory number, input terminal, frequency and sync signal are automatically identified and displayed.

When MENU is pressed, the “REGISTERED • SIGNAL LIST” screen is restored.

Press ENTER.3.

The “RENAME” screen will be displayed.•

SVGA72-A2 A2 RGB1

48.08kHz

72.17Hz H(POS) V(POS)

Basic Operation

MENU SELECT

ENTER

SUB MENU

ENGLISH

– 45

Registration of input signal data (continued)

Use ▲▼◄► to select the

4. characters and numerals one by one, and press ENTER to set them.

RENAME

NAME MEMORY NO INPUT fH fV

ABCDEFGHIJKLMNO

SYNC.STATE

PQRSTUVWXYZ;:,.

abcdefghijklmno

pqrstuvwxyz/+-*

0123456789 _@[]

< > BS OK CANCEL

Once the name has been

SVGA72-A2 A2 RGB1

48.08kHz

72.17Hz H(POS) V(POS)

The projector is provided with a sub memory function to register plural pieces of image adjustment data even they are determined to be the same signal by the frequency and form of the synchronization signal source. Use this function when the user needs adjustment of picture quality such as aspect switching and white balance using the same signal source. Sub-memory contains all data that can be adjusted by signals such as screen aspect ratio and image adjustment data (BRIGHTNESS, CONTRAST etc.).

changed, press ▲▼◄► to select “OK” and then press ENTER.

After registration, the “REGISTERED SIGNAL • STATUS” screen is restored.

If you would like to cancel the changes to the • signal name, use ▲▼◄► to select “CANCEL” and then press ENTER. The changes will be cancelled and the displayed signal name will remain as it is.

Clearing the data of registered signals

Press ▲▼◄► to select the signal

1. whose data is to be cleared.

REGISTERED SIGNAL LIST

A1:NTSC-A1 VIDEO −−−

A2:SVGA72-A2 RGB1 −−−

A3:SXGA+60-A3 RGB1 −−− A4:VGA60-A4 RGB1 −−− A5:VGA85-A5 RGB1 −−− A6:NTSC-A6 S-VIDEO −−− A7:1080i/60i-A7 RGB1 −−− A8:1080/24p-A8 RGB1 −−−

Press DEFAULT.2.

The “ENTRY SIGNAL CLEAR” screen will be • displayed.

If the data is not to be cleared, press MENU to • return to the “SIGNAL LIST” screen.

ENTRY SIGNAL CLEAR

NAME MEMORY NO INPUT fH fV SYNC.STATE

SURE?

SVGA72-A2 A2 RGB1

48.08kHz

72.17Hz H(POS) V(POS)

Sub memory

How to register into sub memory



A new signal cannot be registered into sub memory. A new signal must undergo signal registration.

Press ◄► on normal screen 1. (menu is not displayed).

A “Check sub-memory registration” screen will • appear if sub-memory has not been registered.

The screen will show a list of the sub-memory • registered for the currently entered signal.

If “SUB MEMORY” is selected from the • “FUNC1” menu in the “PROJECTOR SETUP” menu, you can use the FUNC1 button instead of the ◄► buttons. (p. 83)

Check sub-memory registration screen

NAME MEMORY NO INPUT fH fV SYNC.STATE

SUB MEMORY LIST screen

SUB MEMORY LIST 1-1:SXGA60-A1

1-2:SXGA60-A2 1-3:––– 1-4:––– 1-5:––– 1-6:––– 1-7:––– 1-8:–––

Press ▲▼◄► to select the SUB 2. MEMORY number stored in the “SUB MEMORY LIST”.

SXGA60-A1 A1 RGB1

64.00kHz

60.00Hz H(POS) V(POS)

46 –

Press ENTER.3.

The data of the signal selected is cleared.•

ENGLISH

Press ENTER.3.

A “Change registered signals” screen will appear.•

RENAME

NAME MEMORY NO INPUT fH fV

ABCDEFGHIJKLMNO

SYNC.STATE

PQRSTUVWXYZ;:,.

abcdefghijklmno

pqrstuvwxyz/+-*

0123456789 _@[]

< > BS OK CANCEL

SXGA60-A1 A1 RGB1

64.00kHz

60.00Hz H(POS) V(POS)

Press ENTER.4.

Note

To rename a registered signal, perform steps 4 and • 5 on page 46.

Procedure to switch to sub



memory

Press ◄► on normal screen 1. (menu is not displayed).

The screen will show a list of the sub-memory • registered for the currently entered signal.

Details of registered signal

REGISTERED SIGNAL STATUS

NAME MEMORY NO INPUT fH fV SYNC.STATE

SXGA60-A1 A5 (1-2) RGB1

63.98kHz

60.02Hz H(POS) V(POS)

The designation can be set by the sub memory • items. MEMORY NO : A1 (1-2)

Sub memory number

The place in which address code (A1, A2, ..., H7 and H8) signals are registered

Note

Restrictions

The maximum sub memory items that can be • registered for the projector are 96 including the basic signal.

Basic Operation

Press ▲▼◄► to select the 2. sub-memory signal to be switched in the “SUB MEMORY LIST”.

Press ENTER.3.

Signal will be switched to the one that was • selected in Step 2.

How to erase sub memory



The currently selected SUB MEMORY is deleted by pressing DEFAULT at the “REGISTERED SIGNAL LIST”.

On-screen indications



Input switching / signal switching

This shows the registered signal name on the status screen for signal switching.

INPUT NAME MEMORY NO

RGB1 RGB A1(1-2)

ENGLISH

– 47

Basic operations using the remote control

Switching the input signal

You can use the remote control to switch the signals that are being input and projected.

Press INPUT SELECT on the 1. remote control or the main unit.

Press RGB1:•

Switches to RGB1 input.

Press RGB2:•

Switches to RGB2 input.

Press DVI-D:•

Switches to DVI-D input.

Press VIDEO:•

Switches to video input.

Press S-VIDEO:•

Switches to S-VIDEO input.

Press AUX:•

Switches to optional input module input. (The AUX button to switch the input is disabled when an optional input module is not connected.)

INPUT SELECT

ON SCREEN

TEST PATTERN

STATUS LIGHT

AUTO SETUP

SHUTTER

ASPECT

FUNC1

Using the SHUTTER function

If the projector is not used for a certain period of time during the meeting intermission, for example, a shutter mode is available that allows the user to hide images temporarily.

Press SHUTTER on the remote 1. control or the main unit.

The image is turned off.•

Press SHUTTER again.2.

The image comes back.•

On-screen display function

This turns the on-screen display function on and off.

Press ON SCREEN on the 1. remote control.

Note

Refer to “Connection” for details on the input • terminals. (pp. 27-29)

Status function

This shows the projector status. It can also be used to send information about the projector’s status via e-mail.

Press STATUS on the remote 1. control.

The “STATUS” screen will be displayed.•

STATUS

INPUT NAME SIGNAL FREQUENCY PROJECTOR RUNTIME LAMP1 LAMP2 LAMP3 LAMP4 INTAKE AIR TEMP. OPTICS MODULE TEMP. AROUND LAMP TEMP. REMOTE2 STATUS

Note

Refer to “STATUS” of “PROJECTOR SETUP”. • (p. 81)

Refer to “How to use network function” for details • on sending e-mail. (pp. 91-104)

RGB2

XGA60-A399999

48.36kHz/59.99Hz 76h

341h / ON / 334h / ON / 342h / ON /

97h / ON /

31°C/87°F 27°C/80°F 31°C/87°F

DISABLE

1/3

48 –

ENGLISH

Automatic adjustment

Turning on button

(AUTO SETUP)

The automatic setup function can be used to automatically adjust the resolution, clock phase and picture position when analogue RGB signals consisting of bitmap images such as computer signals are being input, or to automatically adjust the picture position when DVI-D signals are being input. (The automatic setup function does not work with video format signals such as signals output from a DVD player.) It is recommended to supply images with a bright white frame at the outermost periphery containing characters etc. that are clear in white and black contrast when the system is in automatic adjustment mode. Avoid supplying images that involve halftones or gradation such as photographs and computer graphics.

Press AUTO SETUP on the 1. remote control or the main unit.

A message “COMPLETE” appears if • adjustment is ended normally.

Note

“CLOCK PHASE” may have been shifted even • when the adjustment ended normally. In this case, manually adjust the “CLOCK PHASE”.

If an image with blurred edges or a dark • image is input, “INCOMPLETE” may appear or adjustment may not be performed properly even if “COMPLETE” appears. In this case, manually adjust the items of “INPUT RESOLUTION”, “CLOCK PHASE” and “SHIFT”.

For specific signals and long-sideways (or • landscape) signals such as 16:9, adjustment should be made according to “AUTO SETUP” in the option menu.

Automatic adjustment may not be available • depending on the machine type of the personal computer.

Automatic adjustment may not available for • synchronization signal of C-SYNC and G-SYNC.

Image may be distorted for several seconds during • automatic adjustment. This is not a malfunction.

For every supplied signal, adjustment is required.• Automatic adjustment can be cancelled by pressing •

the MENU button during the course of automatic adjustment.

Even for an RGB signal for which automatic setup • is possible, if automatic setup is performed while moving images are being input, “INCOMPLETE” may appear, or adjustment may not be performed properly even if “COMPLETE” appears.

illumination

Button illumination for the remote control can be turned on.

Press LIGHT on the remote 1. control.

Note

If no operations are carried out for approximately • 10 seconds, button illumination will turn off automatically.

Using the FUNC1 button

“DISABLE”, “P IN P” (pp. 85-86), “SUB MEMORY” (pp. 46-47), “SYSTEM SELECTOR” (pp. 58-59), “SYSTEM DAYLIGHT VIEW” (pp. 56-57), or “FREEZE” (p. 83) operations can be assigned to the FUNC1 button on the remote control so that it can be used as an easy shortcut button.

Note

Refer to “Setting FUNC1” for details. (p. 83)•

Basic Operation

Displaying the internal test pattern

The projector has eight types of internal test patterns to check the condition of the set. To display test patterns, follow the steps below.

Press TEST PATTERN.1.

Press ◄► to select “TEST 2. PATTERN”.

Note

Setting is also possible by using an on-screen • menu. Refer to “Displaying the internal test pattern” for details. (p. 87)

Results of adjustment on the image, picture quality, • position, size and other factors will not be reflected in test patterns. Be sure to display the input signal before performing various kinds of setting.

ENGLISH

– 49

Basic operations using the remote control (continued)

Changing the picture aspect ratio

You can change the aspect ratio for projected pictures to match the input signal.

Press ASPECT on the remote 1. control.

The setting will change as follows each time • ASPECT is pressed.

VID AUTO (PRI.) DEFAULT

S1 AUTO THROUGH

VID AUTO 16:9

HV FIT 4:3

V FIT H FIT

Note

Some aspect ratios may not be available for • selection depending on the input signal. Refer to “Adjusting the aspect ratio” for details. (p. 61)

50 –

ENGLISH

On-screen menus

MAIN MENU

The main menu consists of the following 11 menu items. When a main menu item is selected, the screen changes to a sub-menu selection screen.

Icon MAIN MENU item

▲▼◄►

ENTER

DEFAULT

Menus are extensively used for configuring, adjusting or reconfiguring the projector.

Press to display the MAIN MENU screen.

Select the item to be set.

Press to display the menu of the desired item.

MAIN MENU PICTURE

POSITION ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION

PROJECTOR SETUP

P IN P TEST PATTERN SIGNAL LIST SECURITY NETWORK

MENU SELECT

ENTER

SUB MENU

PICTURE

POSITION

ADVANCED MENU

DISPLAY LANGUAGE

DISPLAY OPTION

PROJECTOR SETUP

P IN P

TEST PATTERN

SIGNAL LIST

SECURITY

NETWORK

SUB MENU

The sub-menu screen for the selected main menu item appears, and you can then set and adjust the various items in the sub-menu.

PICTURE (pp. 54-59)



PICTURE PICTURE MODE

CONTRAST BRIGHTNESS COLOR TINT COLOR TEMPERATURE GAMMA SYSTEM DAYLIGHT VIEW SHARPNESS NOISE REDUCTION DYNAMIC IRIS

SYSTEM SELECTOR

MENU SELECT CHANGE REGISTER

ENTER

Note

The factory default values may vary depending on • the PICTURE menu.

STANDARD

0 0 0

0 DEFAULT DEFAULT

OFF

OFF OFF

AUTO1

Basic Operation

Some menu items may not be valid for certain • signal formats applied to the projector. The menu items that cannot be adjusted or used are shown in gray characters, and they cannot be selected.

ENGLISH

– 51

On-screen menus (continued)

POSITION (pp. 60-63)



POSITION SHIFT

ASPECT ZOOM CLOCK PHASE GEOMETORY

MENU SELECT

ENTER

SUB MENU

ADVANCED MENU (pp. 64-68)



ADVANCED MENU DIGITAL CINEMA REALITY

BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING FRAME DELAY RASTER POSITION

DEFAULT

OFF

AUTO

OFF

DEFAULT

PROJECTOR SETUP (pp. 77-84)



PROJECTOR SETUP PROJECTOR ID

INSTALLATION ALTITUDE MODE DIRECTION LAMP SELECT LAMP RELAY RS-232C REMOTE2 MODE STATUS AIR FILTER CLEANING AUTO POWER OFF FUNC1

MENU SELECT CHANGE

PROJECTOR SETUP DATE AND TIME

SAVE ALL USER DATA LOAD ALL USER DATA INITIALIZE SERVICE PASSWORD

P IN P (pp. 85-86)



TEST PATTERN (p. 87)



SIGNAL LIST (pp. 45-47)



ALL

FRONT-FLOOR

HORIZONTAL

QUAD

OFF

DEFAULT

DISABLE

1/2

2/2

MENU SELECT CHANGE

DISPLAY LANGUAGE (p. 69)



DISPLAY LANGUAGE

ENGLISH

DEUTSCH FRANÇAIS ESPAÑOL ITALIANO

日本語

中文 русский 한국어

SELECT

ENTER

SET

DISPLAY OPTION (pp. 70-76)



DISPLAY OPTION COLOR MATCHING

LARGE SCREEN CORRECTION SCREEN SETTING RGB IN DVI-D IN AUX DVI IN AUX SDI IN ON-SCREEN DISPLAY BACK COLOR STARTUP LOGO

OFF OFF

BLACK LOGO3

SECURITY (pp. 88-90)



SECURITY SECURITY PASSWORD

SECURITY PASSWORD CHANGE DISPLAY SETTING TEXT CHANGE CONTROL DEVICE SETUP

MENU SELECT CHANGE

NETWORK (pp. 91-104)



NETWORK NETWORK STANDBY

NETWORK SETUP NETWORK CONTROL NETWORK STATUS

MENU SELECT CHANGE

OFF

52 –

MENU SELECT CHANGE

ENGLISH

Using the menu screens

Press MENU.1.

The “MAIN MENU” appears on the screen.•

MAIN MENU PICTURE

POSITION ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION

PROJECTOR SETUP

P IN P TEST PATTERN SIGNAL LIST SECURITY NETWORK

MENU SELECT

ENTER

SUB MENU

Press ▲▼ to select the desired 2. item.

The selected item is displayed with the colours • set by OSD DESIGN. (p. 75)

MAIN MENU

PICTURE

POSITION

ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION

PROJECTOR SETUP

P IN P TEST PATTERN SIGNAL LIST SECURITY NETWORK

MENU SELECT

ENTER

SUB MENU

Press ▲▼ button to highlight the 4. desired adjustment item, then press ◄► to change or adjust the parameter value.

For some items, an individual adjustment • screen containing a bar scale will appear as shown in the diagram below when ◄► is pressed.

CONTRAST

ADJUST

If no button is operated for approx. 5 seconds • while the individual adjustment screen is displayed, the screen will return to the previous page.

Returning to the previous screen



When the “MENU” is on the screen, pressing • the MENU button returns to the previous page.

When the “MAIN MENU” is on the screen, • pressing MENU clears all menus from the screen.

Menu items setting



The bottom prompt line differs on each menu • depending on the selected menu option:

A prompt “◄► CHANGE” appears when • changing the setting.

A prompt “◄► ADJUST” appears for a • separate bar graph.

If there are more adjustments (items) available • for a menu item, a page number will appear at the top-right of the screen.

Basic Operation

Press ENTER to establish your 3. selection.

The submenu for the selected option will now • open.

POSITION SHIFT

ASPECT ZOOM CLOCK PHASE GEOMETORY

MENU SELECT

ENTER

SUB MENU

DEFAULT

OFF

Resetting to the factory default

If an adjustment item is selected and DEFAULT is pressed, the adjustment value will return to the factory default setting.

Press DEFAULT.1.

PICTURE PICTURE MODE

CONTRAST BRIGHTNESS COLOR TINT COLOR TEMPERATURE GAMMA SYSTEM DAYLIGHT VIEW SHARPNESS NOISE REDUCTION DYNAMIC IRIS

SYSTEM SELECTOR

MENU SELECT CHANGE REGISTER

ENTER

STANDARD

0 DEFAULT DEFAULT

OFF

OFF OFF

AUTO1

ENGLISH

– 53

Adjusting the picture

Switching the picture mode

The user can switch to the desired picture mode suitable for the image source and the environment in which this projector is used.

Press ▲▼ to select “PICTURE 1.

▲▼◄►

ENTER

MODE”.

PICTURE PICTURE MODE

CONTRAST

Press ◄► to switch “PICTURE 2. MODE”.

The setting will change as follows each time • ◄► is pressed.

STANDARD

DEFAULT

You can adjust pictures to suit your preference.

Press to display the MAIN MENU screen.

Press to select “PICTURE”.

Press to display the “PICTURE” menu.

MAIN MENU PICTURE

POSITION ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION

PROJECTOR SETUP

P IN P TEST PATTERN SIGNAL LIST SECURITY NETWORK

STANDARD

USER

CINEMA

GRAPHIC

NATURAL

DYNAMIC

STANDARD:• The picture becomes suitable for moving images in general.

CINEMA:• The picture becomes suitable for movie sources.

NATURAL:• The picture complies with sRGB.

DYNAMIC:• The picture becomes suitable for the use in welllighted areas.

GRAPHIC:• The picture becomes suitable for input from to the personal computer.

USER:• The COLOR TEMPERATURE and GAMMA settings can be adjusted.

Note

Factory defaults are “GRAPHIC” for RGB system • and “STANDARD” for moving images.

When ENTER is pressed while “PICTURE MODE” • has been selected, the picture mode which has been selected can be saved and used as the presetting when new signals are input. The data will be saved for all items in the PICTURE menu except for the SYSTEM SELECTOR setting.

54 –

MENU SELECT

ENTER

SUB MENU

Some menu items may not be valid for certain • signal formats applied to the projector.

ENGLISH

Adjusting Contrast

This adjusts the contrast for picture colours.

Press ▲▼ to select 1. “CONTRAST”.

PICTURE MODE

CONTRAST BRIGHTNESS

STANDARD

0 0

Press ◄► or ENTER.2.

The “CONTRAST” individual adjustment screen • will be displayed.

CONTRAST

Press ◄► or ENTER.2.

The “COLOR” individual adjustment screen will • be displayed.

COLOR

ADJUST

Press ◄► to adjust the level.3.

Operation Adjustment

Press ► button.

Press ◄ button.

Raises the picture brightness and the picture becomes clearer.

Lowers the picture brightness and weakens the picture.

Attention

If you need to adjust the “BRIGHTNESS”, it should • be adjusted before other adjustments are made.

Adjustment

range

Maximum value

Minimum value

-31

Adjusting Brightness

This adjusts the brightness of dark (black) areas of the pictures.

Press ▲▼ to select 1. “BRIGHTNESS”.

CONTRAST

BRIGHTNESS COLOR

Press ◄► or ENTER.2.

The “BRIGHTNESS” individual adjustment • screen will be displayed.

BRIGHTNESS

ADJUST

0 0 0

ADJUST

Press ◄► to adjust the level.3.

Operation Adjustment

Press ► button.

Press ◄ button.

Deepens colours.

Weakens colours.

Adjusting Tint

This adjusts skin tones in the pictures.

Press ▲▼ to select “TINT”.1.

COLOR

TINT COLOR TEMPERATURE

Press ◄► or ENTER.2.

The “TINT” individual adjustment screen will be • displayed.

TINT

ADJUST

Press ◄► to adjust the level.3.

Operation Adjustment

Press ► button.

Press ◄ button.

Adjusts skin tone toward reddish-purple.

Adjusts skin tone toward greenish colour.

Adjustment

range

Maximum value

Minimum value

-50

0 DEFAULT

Adjustment

range

Maximum value

Minimum value

-31

Basic Operation

Press ◄► to adjust the level.3.

Operation Adjustment

Increases the Press ► button.

Press ◄ button.

brightness of the dark

(black) parts of the

screen.

Reduces the brightness

of the dark (black) parts

of the screen.

Adjusting Colour

This adjusts the depth of the colours.

Press ▲▼ to select “COLOR”.1.

BRIGHTNESS

COLOR TINT

Adjustment

range

Maximum value

Minimum value

-31

0 0 0

Adjusting the colour temperature

This is used to adjust the pictures if white areas appear bluish or reddish.

Carry out this adjustment while the signals to be • adjusted are being projected.

Press ▲▼ to select “COLOR 1. TEMPERATURE”.

TINT COLOR TEMPERATURE GAMMA

0 DEFAULT DEFAULT

Press ◄► or ENTER.2.

The “COLOR TEMPERATURE” individual • adjustment screen will be displayed.

COLOR TEMPERATURE

CHANGE

DEFAULT

ENGLISH

– 55

Adjusting the picture (continued)

Press ◄► to switch “COLOR 3. TEMPERATURE”.

The setting will change as follows each time • ◄► is pressed.

DEFAULT

HIGH

When any setting other than “OFF” has been • selected for colour matching, the COLOR TEMPERATURE setting is fixed at “USER1”.

“DEFAULT” cannot be selected when the picture • mode has been set to “USER”.

To further adjust toward the



USER1

MIDDLE

USER2

LOW

desired white balance

Select “USER1” or “USER2” in 4. Step 3.

Press ENTER.5.

The “WHITE BALANCE” screen will be • displayed.

WHITE BALANCE WHITE BALANCE HIGH

WHITE BALANCE LOW

Press ▲▼ to select “WHITE 6. BALANCE HIGH” or “WHITE BALANCE LOW”.

Press ENTER.7.

The “WHITE BALANCE HIGH (LOW)” screen • will be displayed.

WHITE BALANCE HIGH RED

GREEN

255 255

Press ▲▼ to select “RED”, 8. “GREEN” or “BLUE”.

Note

All colours will not be displayed properly unless • adequate adjustment is made. If the adjustment does not look suitable, you can press DEFAULT to return the setting for the selected item only to the factory default setting.

The colour temperature cannot be adjusted for the • internal test pattern (p. 87). Be sure to project the input signal when adjusting the colour temperature.

Gamma setting

This switches the gamma mode.

Press ▲▼ to select “GAMMA”.1.

COLOR TEMPERATURE

GAMMA SYSTEM DAYLIGHT VIEW

Press ◄► or ENTER.2.

The “GAMMA” individual adjustment screen • will be displayed.

GAMMA

CHANGE

Press ◄► to switch “GAMMA”.3.

The setting will change as follows each time • ◄► is pressed.

DEFAULT

2.6

* “USER1” and “USER2” appear when the setting

was set with a control command from the serial terminal.

Note

“DEFAULT” cannot be selected when the picture • mode has been set to “USER”.

USER1*

2.5

DEFAULT DEFAULT

OFF

DEFAULT

USER2*

2.2

56 –

Press ◄► to adjust the level.9.

Item Operation Adjustment

RED

GREEN

BLUE

Press ► button.

Press ◄ button.

Press ► button.

Press ◄ button.

Press ► button.

Press ◄ button.

Deepens red.

Weakens red.

Deepens green.

Weakens green.

Deepens blue.

Weakens blue.

ENGLISH

Adjustment

range

Maximum

value

HIGH : 255

LOW : 127

Minimum

value

HIGH : 0

LOW : -127

Default

HIGH : 255

LOW : 0

System daylight view setting

This corrects images so that they appear vivid when projected under bright lighting.

Press ▲▼ to select “SYSTEM 1. DAYLIGHT VIEW”.

GAMMA

SYSTEM DAYLIGHT VIEW SHARPNESS

DEFAULT

OFF

Press ◄► or ENTER.2.

The “SYSTEM DAYLIGHT VIEW” individual • adjustment screen will be displayed.

SYSTEM DAYLIGHT VIEW

CHANGE

OFF

Press ◄► to switch “SYSTEM 3. DAYLIGHT VIEW”.

The setting will change as follows each time • ◄► is pressed.

Press ◄► to switch “NOISE 3. REDUCTION”.

The setting will change as follows each time • ◄► is pressed.

OFF (No correction)

3 (High)

1 (Low)

2 (Medium)

Sharpness setting

This adjusts the sharpness of the pictures.

Press ▲▼ to select 1. “SHARPNESS”.

SYSTEM DAYLIGHT VIEW SHARPNESS NOISE REDUCTION

OFF

Press ◄► or ENTER.2.

The “SHARPNESS” individual adjustment • screen will be displayed.

SHARPNESS

ADJUST

Press ◄► to adjust the level.3.

Operation Adjustment

Press ► button.

Press ◄ button.

Contours become sharper.

Contours become softer.

Note

The possible setting range will vary depending on • the input signal.

Adjustment

range

0 to 15

Noise reduction setting

This can be used to adjust pictures if they contain interference as a result of poor quality of the input signal.

Press ▲▼ to select “NOISE 1. REDUCTION”.

SHARPNESS NOISE REDUCTION DYNAMIC IRIS

Press ◄► or ENTER.2.

The “NOISE REDUCTION” individual • adjustment screen will be displayed.

NOISE REDUCTION

CHANGE

OFF OFF

OFF

OFF (No correction)

3 (High)

1 (Low)

2 (Medium)

Note

When “FRAME DELAY” is set to “SHORT”, the • noise reduction setting function cannot be used.

Dynamic iris setting

Pictures with the optimum contrast will be displayed by automatically providing aperture compensation and signal compensation to suit the pictures concerned.

Press ▲▼ to select “DYNAMIC 1. IRIS”.

NOISE REDUCTION

DYNAMIC IRIS

SYSTEM SELECTOR

Press ◄► or ENTER.2.

The “DYNAMIC IRIS” individual adjustment • screen will be displayed.

DYNAMIC IRIS

CHANGE

Press ◄► to switch “DYNAMIC 3. IRIS”.

The setting will change as follows each time • ◄► is pressed.

OFF (No correction)

USER 3 (High)

To further adjust the selected



compensation amount

Select “USER” in step 3.4.

Press ENTER.5.

The “DYNAMIC IRIS” screen will be displayed.•

DYNAMIC IRIS AUTO IRIS

MANUAL IRIS DYNAMIC GAMMA

Use ▲▼ to select the item to be 6. adjusted, and then use ◄► to adjust the amount of correction.

OFF OFF

AUTO1

OFF

1 (Low)

2 (Intermediate)

OFF OFF OFF

Basic Operation

ENGLISH

– 57

Adjusting the picture (continued)

AUTO IRIS (Automatic aperture



adjustment)

OFF (No automatic

adjustment)

1 (Low)

Setting the system selector

This enables the projector to automatically recognize input signals. Furthermore, if unstable signals are input, the system format can be selected manually.

3 (High)

MANUAL IRIS (Fixed aperture



2 (Intermediate)

adjustment)

OFF (No fixed iris)

63 (High)

DYNAMIC GAMMA (signal



1 (Low)

2…62 (Intermediate)

compensation amount adjustment)

OFF (No automatic

correction)

3 (High)

Note

The contrast is set to the maximum level when • “DYNAMIC IRIS” is set to “3”.

1 (Low)

2 (Intermediate)

Registering the picture mode settings as presettings

The picture settings that have been made in the PICTURE MODE screen can be registered.

Select “PICTURE MODE” in the “PICTURE” screen • to carry out this operation.

Press ▲▼ to select “SYSTEM 1. SELECTOR”.

NOISE REDUCTION DYNAMIC IRIS

SYSTEM SELECTOR

OFF OFF

AUTO1

Press ENTER.2.

The “SYSTEM SELECTOR” screen will be • displayed.

SYSTEM SELECTOR

C AUTO1

AUTO2

Press ▲▼ to switch “SYSTEM 3. SELECTOR”, and then press ENTER.

The system formats that can be selected differ • depending on the input signals.

S-video / Video terminal input



signal

Select from AUTO1, AUTO2, NTSC, NTSC4.43, PAL, PALM, PAL-N, SECAM, and PAL60.

Note

Press the DEFAULT button to return to “AUTO1”.• “AUTO1” automatically selects from NTSC, •

PAL, SECAM, NTSC4.43, and PAL60. “AUTO2” automatically selects from NTSC, PAL-M, and PAL-N.

58 –

Press ENTER.1.

A confirmation screen will appear.•

SAVE AS DEFAULT SETTING FOR DYNAMIC?

OK CANCEL

 CHANGE

ENTER

 EXECUTE

Press ◄► to select “OK”.2.

Press ENTER.3.

Note

If the registered picture mode is selected after • registering the picture mode settings as presettings, the new signals will be displayed with the registered adjustments.

ENGLISH

RGB1 / RGB2 / DVI-D terminal



input signal

Select from RGB and YPBPR.

Note

Refer to the types of signals compatible with the • projector. (pp. 122-123)

Input module



ET-MD77SD1:

Select from AUTO, 480i and 576i.

ET-MD77SD3:

Select from AUTO, 1 080/60i, 1 035/60i, 720/60p, 1 080/24p, 1 080/50i, 1 080/30p, 1 080/25p, 1 080/24sF, 720/50p, and 480i, 576i.

ET-MD100SD4:

When single link SDI signals Select from AUTO YCbCr, 1 080/60i, 1 035/60i, 720/60p, 1 080/24p, 1 080/50i, 1 080/30p, 1 080/25p, 1 080/24sF, 720/50p, 480i, and 576i. When dual link SDI signals Select from AUTO RGB, AUTO X’Y’Z’, 1 920/24p/RGB, 2 048/24p/RGB, 2 048/24p/XYZ, 1 920/24sF/RGB, 2 048/24sF/RGB, 2 048/24sF/ XYZ, 1 920/25p/RGB, 1 920/30p/RGB, 1 920/50i/ RGB, and 1 920/60i/RGB.

Note

Press the DEFAULT button to return to AUTO • YCbCr or AUTO RGB.

“AUTO RGB” automatically selects from 1 920/24p/• RGB, 2 048/24p/RGB, 1 920/24sF/RGB, 2 048/24sF/RGB, 1 920/25p/RGB, 1 920/30p/RGB, 1 920/50i/RGB, and 1 920/60i/RGB. “AUTO X’Y’Z’” automatically selects from 2 048/24p/XYZ and 2 048/24sF/XYZ.

To display pictures complying

Follow the same procedure 7. (steps 5-6) to restore the factory default for “TINT”, “COLOR TEMPERATURE” and “GAMMA”.

Note

sRGB is only enable when RGB signals are being • input.

with the sRGB standard

sRGB is the international colour reproduction standard (IEC61966-2-1) established by IEC (International Electrotechnical Commission). To reproduce colours more faithfully in compliance with the sRGB standard, perform the following setting procedure.

Set “COLOR MATCHING” 1. adjustment to “OFF”. (p. 70)

Display the “PICTURE” screen. 2. (p. 54)

Press ▲▼ to select “PICTURE 3. MODE”.

PICTURE PICTURE MODE

CONTRAST

Press ◄► to select “NATURAL”.4.

Press ▲▼ to select “COLOR”.5.

BRIGHTNESS

COLOR TINT

NATURAL

0 0 0

Basic Operation

Press DEFAULT on the remote 6. control to restore the factory default.

ENGLISH

– 59

Adjusting the position

Shift adjustment

This function allows the user to adjust the picture position vertically or horizontally if the position of the image projected on the screen is displaced when the projector is properly positioned against the screen.

Press ▲▼ to select “SHIFT”.1.

▲▼◄►

ENTER

DEFAULT

POSITION SHIFT

ASPECT

Press ENTER.2.

The “SHIFT” screen will be displayed.•

SHIFT V

Press ▲▼◄► to adjust the 3. position.

For horizontal (right and left)



adjustment

DEFAULT

212

You can adjust the position as required.

MAIN MENU

PICTURE

POSITION

ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION

PROJECTOR SETUP

P IN P TEST PATTERN SIGNAL LIST SECURITY NETWORK

MENU SELECT

ENTER

SUB MENU

Press to display the MAIN MENU screen.

Press to select “POSITION”.

Press to display the “POSITION” menu.

Operation Adjustment

The picture

Press ► button.

Press ◄ button.

For vertical (up and down)



position moves to the right.

The picture position moves to the left.

adjustment

Operation Adjustment

The picture

Press ▲ button.

Press ▼ button.

position moves up.

The picture position moves down.

Press MENU three times.4.

The on-screen indications disappear and the • normal screen appears again.

60 –

ENGLISH

Adjusting the aspect ratio

This changes the aspect ratio of the pictures. This changes the aspect ratio for the screen range selected with “SCREEN SETTING”. Set “SCREEN SETTING” first. (p. 72)

Press ▲▼ to select “ASPECT”.1.

SHIFT

ASPECT

ZOOM

Press ◄► or ENTER.2.

The “ASPECT” individual adjustment screen • will be displayed.

ASPECT

CHANGE

Press ◄► to switch “ASPECT”.3.

The setting will change as follows each time • ◄► is pressed.

VID AUTO (PRI.) DEFAULT

S1 AUTO THROUGH

VID AUTO 16:9

HV FIT 4:3

V FIT H FIT

DEFAULT:• Pictures are displayed without changing the aspect ratio of the input signals. THROUGH:• Pictures are displayed without changing the resolution of the input signals. 16:9:• When standard signals*1 are input, the pictures are displayed with the aspect ratio converted to 16:9. When wide signals are input*2, the pictures are displayed without changing the aspect ratio. 4:3:• When standard signals are input*1, the pictures are displayed without changing the aspect ratio. When wide signals are input*2, the PT-D12000E displays pictures with the aspect ratio converted to 4:3. The PT-DZ12000E displays pictures reduced to fit a 4:3 screen without changing the input aspect ratio. H FIT:• The display will use the full width of the screen range selected with “SCREEN SETTING”. When signals have a vertical aspect ratio that is larger than the screen aspect selected with “SCREEN SETTING”, the pictures will be displayed with their bottom areas cut off.

DEFAULT

V FIT:• The display will use the full height of the screen range selected with “SCREEN SETTING”.

HV FIT:• The pictures are displayed in the full screen range selected with “SCREEN SETTING”. If the aspect ratios of the input signals and screen range differ, conversion to the screen aspect set with “SCREEN SETTING” is performed and then the pictures are displayed.

VID AUTO:• The projector identifies the video ID (VID) embedded in the picture signals and displays the picture by automatically switching the screen sizes between 4:3 and 16:9. This function is effective for the NTSC signal input.

S1 AUTO:• The projector identifies the S1 signal and displays the picture by automatically switching the screen sizes between 4:3 and 16:9. This function is effective for S-Video NTSC signals.

VID AUTO (PRI.):• The projector identifies the abovementioned VID or S1 signals and displays the picture by automatically choosing the screen sizes of 4:3 or 16:9 according to the VID if it is detected or S1 signals if a VID is not detected. This function is effective for S-Video NTSC signals.

*1: Standard signals are input signals with an aspect

ratio of 4:3 or 5:4.

*2: Wide-screen signals are input signals with an

aspect ratio of 16:10, 16:9, 15:9 or 15:10.

Note

Some size modes are not available for certain types • of input signals. For NTSC signals, “DEFAULT” cannot be selected.

If an aspect ratio which is different from the aspect • ratio for the input signals is selected, the pictures will appear differently from the originals. Be careful of this when selecting the aspect ratio.

If using this projector in places such as cafes or • hotels to display programmes for a commercial purpose or for public presentation, note that adjusting the aspect ratio or using the zoom function to change the screen pictures may be an infringement of the rights of the original copyright owner for that programme under copyright protection laws.

If conventional (normal) 4:3 pictures which are • not wide-screen pictures are displayed on a wide screen, the edges of the pictures may not be visible or they may become distorted. Such pictures should be viewed as with an aspect ratio of 4:3 in the original format intended by the creator of the pictures.

ENGLISH

Basic Operation

– 61

Adjusting the position (continued)

Adjusting the zoom ratio

This adjusts the size of the projected pictures.

Press ▲▼ to select “ZOOM”.1.

ASPECT

ZOOM

CLOCK PHASE

Press ENTER.2.

The “ZOOM” screen will be displayed.•

ZOOM MODE

INTERLOCKED V H

Press ▲▼ to select “MODE”.3.

Press ◄► to switch “MODE”.4.

The setting will change as follows each time • ◄► is pressed.

INTERNAL FULL

DEFAULT

INTERNAL

OFF 100% 100% 100%

Note

When “ASPECT” is set to “THROUGH”, “ZOOM” • will not appear.

When other than “DEFAULT” is selected for • “ASPECT”, the “MODE” selection setting will not appear.

Clock phase adjustment

Clock phase adjustment achieves the best image when the screen flickers or halo is observed around the contour.

Press ▲▼ to select “CLOCK 1. PHASE”.

ZOOM

CLOCK PHASE

GEOMETORY

Press ◄► or ENTER.2.

The “CLOCK PHASE” individual adjustment • screen will be displayed.

CLOCK PHASE

OFF

INTERNAL:• Enlarges the size of the pictures to within the default aspect ratio.

FULL:• Enlarges the size of the pictures using the whole of the display area selected with “SCREEN FORMAT”.

Press ▲▼ to select 5. “INTERLOCKED”.

ZOOM

MODE

INTERLOCKED

V H

INTERNAL

OFF 100% 100% 100%

Press ◄► to switch 6. “INTERLOCKED”.

The setting will change as follows each time • ◄► is pressed.

OFF ON

OFF :• The “V” and “H” settings are used as the vertical and horizontal zoom ratios respectively.

ON :• The zoom ratio is set to the “HV” setting. This allows the pictures to be zoomed at equal vertical and horizontal ratios.

ADJUST

Press ◄► to adjust the level.3.

The value changes from 0 to 31. Adjust so that • the amount of interference is at a minimum.

Note

No optimal value may be obtained if the output • of the PC to which the signal input is applied is unstable.

No optimal value may be obtained if the total • number of dots is not correct.

The clock phase can be adjusted only when RGB • signal input is applied with RGB1 and RGB2 IN.

Adjusting the geometry

Square video can be projected onto a special shaped screen using unique image processing technology.

Press ▲▼ to select 1. “GEOMETRY”.

ZOOM CLOCK PHASE

GEOMETRY

Press ◄► to switch 2. “GEOMETRY”.

The setting will change as follows each time • ◄► is pressed.

OFF

KEYSTONE

62 –

ENGLISH

CURVED

OFF:• Geometry correction is not performed.

KEYSTONE:• This adjusts projected images when they are distorted to a trapezoid.

CURVED:• This adjusts projected images when they are distorted to a curved surface.

PC:• This is for performing geometry correction from a PC.

Select “KEYSTONE” or 3. “CURVED” in Step 2, and then press ENTER.

The “GEOMETRY:KEYSTONE” or • “GEOMETRY:CURVED” screen will be displayed.

GEOMETRY:KEYSTONE VERTICAL KEYSTONE

VERTICAL SUB KEYSTONE

GEOMETRY:CURVED LENS THROW RATIO

VERTICAL KEYSTONE

0 0

LINEARITY•

CURVED menu:

LENS THROW RATIO• Set the throw ratio of the lens you are using. (pp. 22-24)

VERTICAL KEYSTONE•

HORIZONTAL KEYSTONE•

Press ▲▼ to select the desired 4. adjustment item, and press ◄► to adjust the correction amount.

You can adjust the projection images as shown • below.

KEYSTONE menu:

VERTICAL KEYSTONE•

VERTICAL SUB KEYSTONE•

HORIZONTAL KEYSTONE•

VERTICAL ARC•

Basic Operation

HORIZONTAL ARC•

VERTICAL BALANCE•

HORIZONTAL BALANCE•

HORIZONTAL SUB KEYSTONE•

Note

If vertical keystone correction is set, menus and • logos may protrude out of the screen.

If both edge blending adjustment and geometry • correction are used, set the geometry correction to curved-surface correction or PC. If geometry correction is set to keystone-distortion correction, edge blending adjustment cannot be made correctly. (p. 66)

ENGLISH

– 63

How to use ADVANCED MENU

Digital cinema reality

Increase the vertical resolution when the PAL (or SECAM) 576i signal input or the NTSC 480i, 1 080/50i and 1 080/60i signal input is applied.

Press ▲▼ to select “DIGITAL 1. CINEMA REALITY”.

▲▼◄►

ENTER

ADVANCED MENU DIGITAL CINEMA REALITY

BLANKING

Press ◄► or ENTER.2.

The “DIGITAL CINEMA REALITY” individual • adjustment screen will be displayed.

DIGITAL CINEMA REALITY

CHANGE

Press ◄► to switch “DIGITAL 3. CINEMA REALITY”.

The setting will change as follows each time • ◄► is pressed.

AUTO

Fine settings are possible.

Press to display the MAIN MENU screen.

Press to select “ADVANCED MENU”.

Press to display the “ADVANCED MENU” menu.

MAIN MENU

PICTURE POSITION

ADVANCED MENU

DISPLAY LANGUAGE DISPLAY OPTION

PROJECTOR SETUP

P IN P TEST PATTERN SIGNAL LIST SECURITY NETWORK

MENU SELECT

ENTER

SUB MENU

AUTO

30p FIXED: When 480i or 1 080/60i signals are input 25p FIXED: When 576i or 1 080/50i signals are input

OFF

AUTO:• Performs automatic detection and cinema processing. (factory default)

OFF: • Unforced cinema processing

25p FIXED:• Forced cinema processing (2:2 pulldown) is performed when a 576i or 1 080/50i signal is input.

30p FIXED:• Forced cinema processing (2:2 pulldown) is performed when a 480i or 1 080/60i signal is input.

Note

In DIGITAL CINEMA REALITY mode, the image • quality will be deteriorated if 30p FIXED or 25p FIXED is selected when the signal is not a 2:2 pulldown signal.

Blanking adjustment

Blanking adjustment fine-tunes the images projected by the video deck or other devices when the noise appears on the edges of the screen or if a part of the image lies slightly offscreen.

64 –

ENGLISH

Press ▲▼ to select “BLANKING”.

DIGITAL CINEMA REALITY

BLANKING

INPUT RESOLUTION

AUTO

Press ENTER.2.

The “BLANKING” adjustment screen will be • displayed.

BLANKING UPPER

LOWER

0 0

Press ▲▼ to select the desired 3. item for adjustment.

Press ◄► to adjust blanking.4.

The adjustment value for the PT-D12000E can • be changed within a range of 0 to 525 vertically and 0 to 700 horizontally.

The adjustment value for the PT-DZ12000E can • be changed within a range of 0 to 600 vertically and 0 to 960 horizontally.

When correcting the upper blanking of the

screen (top)

Adjusting the input resolution

Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour.

Press ▲▼ to select “INPUT 1. RESOLUTION”.

BLANKING

INPUT RESOLUTION

CLAMP POSITION

Press ENTER.2.

The “INPUT RESOLUTION” screen will be • displayed.

INPUT RESOLUTION TOTAL DOTS

DISPLAY DOTS

1344 1024

Press ◄ button to move the blanking zone upward; ► button to downward.

When correcting the lower blanking of the

screen (bottom)

Press ► button to move the blanking zone upward; ◄ button to downward.

When correcting the left hand blanking of

the screen (left)

Press ► button to move the blanking zone to the right; ◄ button to the left.

When correcting the right hand blanking of

the screen (right)

Press ◄ button to move the blanking zone to the right; ► button to the left.

Press ▲▼ to select “TOTAL 3. DOTS”, “DISPLAY DOTS”, “TOTAL LINES” or “DISPLAY LINES”, and the press ◄► to adjust it.

Each item automatically displays a value in • response to the type of the input signal. If vertical stripes appear on the screen or the image is partly missing, increase or decrease the displayed value while observing the screen to achieve the optimal value.

Note

The abovementioned vertical stripes will not appear • on the screen when all signals are input.

The picture may be distorted during the adjusting • operation, but this is not a fault.

The input resolution can be adjusted only when • RGB signal input is applied with RGB1 and RGB2 IN.

Adjusting the clamp position

Use the clamp position adjustment to achieve the optimal value when dark areas of the image are crushed or displayed in green.

Basic Operation

Press ▲▼ to select “CLAMP 1. POSITION”.

INPUT RESOLUTION

CLAMP POSITION

EDGE BLENDING

OFF

ENGLISH

– 65

How to use ADVANCED MENU (continued)

Press ENTER.2.

The “CLAMP POSITION” screen will be • displayed.

CLAMP POSITION POSITION

ADJUST

Press ◄► to adjust.3.

The value changes from 0 to 255.•

The optimal value for the clamp position • adjustment

If dark areas are crushed: The optimal value is the point where the dark area is best improved. If the dark areas are displayed in green: The optimal value is the point where the green areas become black and the crushing effect is rectified.

Note

The clamp position can be adjusted only when the • RGB signal input is applied with RGB1 and RGB2 IN.

Edge blending adjustment

This projector has the function to hide the seams for multi-screens.

Press ▲▼ to select “EDGE 1. BLENDING”.

CLAMP POSITION

EDGE BLENDING

FRAME DELAY

Press ◄► to switch “EDGE 2. BLENDING”.

The setting will change as follows each time • ◄► is pressed.

OFF

DEFAULT

Press ▲▼ to specify the area to 4. be adjusted.

To joint the top:• set “UPPER” to “ON”. To joint the bottom• : set “LOWER” to “ON”. To joint the left:• set “LEFT” to “ON”. To joint the right:• set “RIGHT” to “ON”.

Press ◄► to toggle “ON” and 5. “OFF”.

Press ◄► to adjust the 6. compensation width and start position.

To display the adjustment



marker

Press ▲▼ to select “MARKER”.7.

RIGHT

MARKER

BRIGHT ADJUST

OFF OFF

Press ◄► to select “ON”.8.

A marker for adjusting the picture position • appears. The optimal point is the position where the red line of one frame overlaps the green line of the other frame. The correction widths of the jointed frames must be the same value all the time. The optimal joint cannot be achieved if the jointed frames have different correction widths.

The optimal point is where

these lines overlap.

66 –

OFF ON USER

OFF:• When the multi-screens are not going to be used.

ON:• When the tilting inside the unit is to be used for the tilting of the edge blending area.

USER:• When a specific tilting is to be used for the tilting of the edge blending area. (Separate software is required to establish these settings. Consult your dealer.)

Press ENTER.3.

The “EDGE BLENDING” screen will be • displayed.

EDGE BLENDING UPPER

START

ENGLISH

Green line

Red line

Press ▲▼ to select “BRIGHT 9. ADJUST”.

RIGHT MARKER

BRIGHT ADJUST

OFF OFF

Press ENTER.

10.

The “BRIGHT ADJUST” screen will be • displayed.

BRIGHT ADJUST BRIGHT INSIDE

BRIGHT OUTSIDE

Press ▲▼ to select “BRIGHT

11. INSIDE”.

12.

Press ENTER.

The “BRIGHT INSIDE” adjustment screen will • be displayed.

BRIGHT INSIDE INTERLOCKED

WHITE

RED GREEN BLUE

When “INTERLOCKED” is set to “OFF”, • individual adjustment of “RED”, “GREEN” and “BLUE” will be possible.

Press ▲▼ to select an item, and

13.

0 0 0 0

press ◄► to adjust the setting.

Once adjustment is complete, press MENU to • return to “BRIGHT ADJUST”.

Press ▲▼ to select the part of

14. “UPPER”, “LOWER”, “RIGHT”, “LEFT”.

15.

Use ◄► to adjust the width for correcting the “BRIGHT INSIDE” setting (0 to 255).

16.

Press ▲▼ to select “BRIGHT OUTSIDE”.

BRIGHT INSIDE

BRIGHT OUTSIDE

OUTSIDE AREA

Press ▲▼ to select an item, and

18. press ◄► to adjust the setting.

Edge blending width (right)Projection

range

BRIGHT adjustment (right)

Marker

BRIGHT OUTSIDE

BRIGHT INSIDE

Note

The BRIGHT adjustment is a function for making • the brightening of the BRIGHT level in those areas where the pictures overlap less conspicuous when multi-screens have been configured using edge blending. The optimal point is where, after the BRIGHT INSIDE has been adjusted, the compensation amount is the same for the BRIGHT levels in the areas where the pictures overlap and where the pictures do not overlap. If, after the BRIGHT INSIDE adjustment, only the vicinity of the borders of the areas where the pictures overlap and where the pictures do not overlap becomes bright, proceed to adjust the top, bottom, left and right widths. Alternatively, if only the vicinity of the borders has darkened as a result of the width adjustments, proceed with the BRIGHT OUTSIDE adjustment.

When a rear screen or screen with a high gain is • used, the joints may appear to be discontinuous depending on the viewing position.

Frame delay

Basic Operation

Press ENTER.

17.

The “BRIGHT OUTSIDE” adjustment screen will • be displayed.

BRIGHT OUTSIDE INTERLOCKED

WHITE

RED GREEN BLUE

When “INTERLOCKED” is set to “OFF”, • individual adjustment of “RED”, “GREEN” and “BLUE” will be possible.

0 0 0 0

When 1 080/60i, 1 080/50i and 1 080/24sF signals are being input, this simplifies image processing so that the frame delay for pictures can be shortened.

Press ▲▼ to select “FRAME 1. DELAY”.

EDGE BLENDING

FRAME DELAY

RASTER POSITION

OFF

DEFAULT

ENGLISH

– 67

How to use ADVANCED MENU (continued)

Press ◄► to switch “FRAME

2. DELAY”.

The setting will change as follows each time • ◄► is pressed.

DEFAULT SHORT

DEFAULT:• This is the standard setting.

SHORT:• This causes the pictures to be delayed after the audio.

Note

When “FRAME DELAY” is set to “SHORT”, • deterioration in the picture quality will occur. Furthermore, the noise reduction function cannot be used.

Raster position

When the whole area where the input picture can be displayed is not used, the picture can be moved to any position inside the display area.

When 16:9 pictures are displayed

(when HDTV or 480p pictures are input or

16:9 is selected in the SIZE mode)

Pressing ▲ button will move the image upward.

Pressing ▼ button will move the image downward.

PT-DZ12000E



When 4:3 pictures are displayed

Pressing ► button will move the image to the right.

Pressing ◄ button will move the image to the left.

Press ▲▼ to select “RASTER 1. POSITION”.

EDGE BLENDING FRAME DELAY

RASTER POSITION

Press ENTER.2.

The “RASTER POSITION” screen will be • displayed.

RASTER POSITION V

Press ▲▼◄► to adjust the 3. position.

PT-D12000E



When 5:4 pictures are displayed

(when SXGA signals are input)

Pressing ► button will move the image to the right.

OFF

DEFAULT

0 0

Press MENU three times.4.

The on-screen indications disappear and the • normal screen appears again.

68 –

Pressing ◄ button will move the image to the left.

ENGLISH

Setting the DISPLAY LANGUAGE

Changing the display language

This lets you switch the on-screen display language.

Press ▲▼ to select the desired 1. language.

▲▼◄►

ENTER

DISPLAY LANGUAGE

ENGLISH

DEUTSCH FRANÇAIS ESPAÑOL ITALIANO

日本語

中文 русский 한국어

Press ENTER to establish your 2. selection.

Menus, setting items, adjustment screens, and • control button names will be displayed in the language the user chooses.

The available languages are: English, German • (DEUTSCH), French (FRANÇAIS), Spanish (ESPAÑOL), Italian (ITALIANO), Japanese (日本語), Chinese (中文), Russian (русский), and Korean (한국어).

Basic Operation

This lets you switch the display language.

Press to display the MAIN MENU screen.

Press to select “DISPLAY LANGUAGE”.

Press to display the “DISPLAY LANGUAGE” menu.

MAIN MENU

PICTURE POSITION ADVANCED MENU

DISPLAY LANGUAGE

DISPLAY OPTION

PROJECTOR SETUP

P IN P TEST PATTERN SIGNAL LIST SECURITY NETWORK

MENU SELECT

ENTER

SUB MENU

Note

The on-screen display of the projector is set to the • English language on shipping.

ENGLISH

– 69

Display Option settings

Adjusting colour matching

When multiple sets are used simultaneously, this projector allows the user to correct the difference of colours among the sets.

Press ▲▼ to select “COLOR 1.

▲▼◄►

ENTER

MATCHING”.

DISPLAY OPTION COLOR MATCHING

LARGE SCREEN CORRECTION

Press ◄► to switch “COLOR 2. MATCHING”.

The setting will change as follows each time • ◄► is pressed.

OFF OFF

DEFAULT

This menu can be used to make a variety of picture and projector settings.

MAIN MENU

PICTURE POSITION ADVANCED MENU DISPLAY LANGUAGE

DISPLAY OPTION PROJECTOR SETUP

P IN P TEST PATTERN SIGNAL LIST SECURITY NETWORK

Press to display the MAIN MENU screen.

Press to select “DISPLAY OPTION”.

Press to display the “DISPLAY OPTION” menu.

OFF 3COLORS

MEASURED

OFF:• Colour matching adjustment is not carried out.

3COLORS:• It is possible to adjust the 3colours of “RED”, “GREEN” and “BLUE”.

7COLORS:• It is possible to adjust the 7colours of “RED”, “GREEN”, “BLUE”, “CYAN”, “MAGENTA”, “YELLOW” and “WHITE”.

709MODE:• Refer to “Adjusting the colour matching using a colorimeter” on the next page for details on this mode.

MEASURED:• Refer to “Adjusting the colour matching using a colorimeter” on the next page for details on this mode.

If “3COLORS” or “7COLORS”



7COLORS

709MODE

was selected in step 2.

Press ENTER.3.

The “3COLORS” or “7COLORS” screen will be • displayed.

3COLORS RED

GREEN BLUE AUTO TESTPATTERN

70 –

MENU SELECT

ENTER

SUB MENU

ENGLISH

Press ▲▼ to select “RED”, 4. “GREEN” and “BLUE” (if “7COLORS” was selected, select “RED”, “GREEN”, “BLUE”, “CYAN”, “MAGENTA”, “YELLOW”, and “WHITE”).

Press ENTER.5.

The “3COLORS:RED”, “3COLORS:GREEN” or • “3COLORS:BLUE” screen will be displayed. If you selected “7COLORS”, the “7COLORS:RED”, “7COLORS:GREEN”, “7COLORS:BLUE”, “7COLORS:CYAN”, “7COLORS:MAGENTA”, “7COLORS:YELLOW”, or “7COLORS:WHITE” screen will be displayed.

3COLORS:RED RED

GREEN BLUE

2048

0 0

Press ◄► to adjust the values.6.

These values can be adjusted from 0 to 2 048.•

Note

The effects of correcting the adjustment colour:• When tuning the correction colour that is the same as the adjustment colour: the brightness of the adjustment colour changes. When tuning the correction colour RED: RED is added to or reduced from the adjustment colour. When tuning the correction colour GREEN: GREEN is added to or reduced from the adjustment colour. When tuning the correction colour BLUE: BLUE is added to or reduced from the adjustment colour.

This adjustment should be carried out by a person • who is familiar with the projector or by a service person because a high level of skill is required to make successful adjustment.

Pressing DEFAULT will restore the factory defaults • for all items.

When any setting other than “OFF” has been • selected for colour matching, the “COLOR TEMPERATURE” setting is fixed at “USER1”.

Adjusting the colour matching using a colorimeter

The “RED”, “GREEN”, “BLUE”, “CYAN”, “MAGENTA”, “YELLOW” and “WHITE” colours can be changed to the desired hues using a colorimeter which is capable of measuring the chromaticity coordinates and luminance.

Inputting the current luminance



and chromaticity coordinates

Press ▲▼ to select “COLOR 1. MATCHING”.

DISPLAY OPTION COLOR MATCHING

LARGE SCREEN CORRECTION

Press ◄► to select 2. “MEASURED” or “709MODE”.

OFF OFF

Press ENTER.3.

The “MEASURED MODE” screen will be • displayed.

MEASURED MODE MEASURED DATA

TARGET DATA AUTO TESTPATTERN

Press ▲▼ to select “MEASURED 4. DATA”.

Press ENTER.5.

The “MEASURED DATA” screen will be • displayed.

MEASURED DATA BLACK Y(RELATIVE)

x y RED Y(RELATIVE) x y GREEN Y(RELATIVE) x y BLUE Y(RELATIVE) x y

0.35

0.36 1400

0.67

0.33 5099

0.35

0.63 500

0.15

0.05

Use the colorimeter to 6. measure the luminance (Y) and chromaticity coordinates (x, y).

Press ▲▼ to select the colours, and

7. press ◄► to select their values.

After all the data has been input, 8. press MENU.

The “MEASURED MODE” screen will be • displayed.

MEASURED MODE

MEASURED DATA

TARGET DATA

AUTO TESTPATTERN

Inputting the coordinates of a



desired colour (only “MEASURED”) Press ▲▼ to select “TARGET 9.

DATA”.

10.

Press ENTER.

The “TARGET DATA” screen will be displayed.•

TARGET DATA RED x

y GREEN x y BLUE x y CYAN x y MAGENTA x y YELLOW x y

0.64

0.33

0.3

0.6

0.15

0.6

0.225

0.329

0.321

0.154

0.419

0.505

1/2

Special Features

1/2

ENGLISH

– 71

Display Option settings (continued)

Press ▲▼ to select the desired

11. colours, and press ◄► to input their coordinates.

12.

After all the data has been input, press MENU.

Note

If “709MODE” has been selected as the “COLOR • MATCHING” setting, the 3 primary colours defined by the ITU-R BT.709 standard will be set as the target data.

If the target data is outside the colour range of the • projector, the colours will not be projected correctly.

Large Screen Correction

If watching images close up on a large screen, you can correct the colours that appear lighter on the screen so that they appear the same as the colours that would appear on a normal-sized screen.

Press ▲▼ to select “LARGE 1. SCREEN CORRECTION”.

COLOR MATCHING

LARGE SCREEN CORRECTION

SCREEN SETTING

Press ◄► to switch “LARGE 2. SCREEN CORRECTION”.

The setting will change as follows each time • ◄► is pressed.

2 (High)

OFF OFF

1 (Low)OFF (No correction)

Press ◄► to switch “SCREEN 3. FORMAT”.

The setting will change as follows each time • ◄► is pressed.

PT-DZ12000E



16:916:10

PT-D12000E



16:94:3

Press ◄► to adjust “SCREEN 4. POSITION”.

In the case of the PT-DZ12000E, you can adjust • the setting from -60 to +60.

In the case of the PT-D12000E, you can adjust • the setting from -132 to +131.

Note

“SCREEN POSITION” cannot be adjusted when • “SCREEN FORMAT” is “16:10” (PT-DZ12000E) and “4:3” (PT-D12000E).

RGB IN (Only RGB input)

When unregistered signals are to be input frequently because the unit is used at conferences or other venues, the screen display position can be adjusted automatically without having to press AUTO SETUP on the remote control each time. Use this setting when adjusting a specific or oblong (16:9, etc.) signal.

Press ▲▼ to select “RGB IN”.1.

SCREEN SETTING

RGB IN

DVI-D IN

72 –

Screen setting

Set this in accordance with the screen you are using. When the projection image aspect ratio is changed, the projector makes corrections to ensure the optimal images for the set screen size.

Press ▲▼ to select “SCREEN 1. SETTING”.

LARGE SCREEN CORRECTION

SCREEN SETTING

RGB IN

OFF

Press ENTER.2.

The “SCREEN SETTING” screen will be • displayed.

SCREEN SETTING SCREEN FORMAT

SCREEN POSITION

16:9

ENGLISH

Press ENTER.2.

The “RGB IN” screen will be displayed.•

RGB IN AUTO SIGNAL

AUTO SETUP

AUTO SIGNAL



Press ▲▼ to select “AUTO 3. SIGNAL”.

OFF

Press ◄► to switch “AUTO 4. SIGNAL”.

The setting will change as follows each time • ◄► is pressed.

OFF ON

If unregistered signals are input when “ON” • is selected, auto setup will be initiated automatically.

AUTO SETUP



Press ▲▼ to select “AUTO 5. SETUP”.

Press ENTER.6.

The “AUTO SETUP” screen will be displayed.•

AUTO SETUP MODE

DEFAULT

Press ◄► to switch “MODE”.7.

The setting will change as follows each time • ◄► is pressed.

DEFAULT WIDE USER

DEFAULT:• To receive signals of which image aspect is 4:3 or 5:4 (applicable resolution : 640 × 400, 640 × 480, 800 × 600, 832 × 624, 960 × 720, 1 024 × 768, 1 152 × 864, 1 152 × 870, 1 280 × 960, 1 280 × 1 024, 1 600 × 1 200, 1 400 × 1 050)

WIDE:• To receive signals of which the image aspect is wide (applicable resolution: 720 x 400, 848 x 480, 1 280 x 720, 1 024 x 600, 1 120 x 750, 1 440 x 900, 1 680 x 1 050)

USER:• To receive signals of specific horizontal resolution (number of horizontally displayed dots)

If “User” is selected, press ◄► 8. to enter the horizontal resolution of signal source into “DISPLAY DOTS”.

Press ENTER.9.

Execute automatic adjustment. A message • “PROGRESS...” appears during automatic adjustment. When the adjustment is complete, the system returns to the input screen.

DVI-D IN

Change this setting if video does not display normally when the projector and an external device are connected via DVI-D.

Press ▲▼ to select “DVI-D IN”.1.

RGB IN

DVI-D IN

AUX DVI IN

Press ENTER.2.

The “DVI-D IN” screen will be displayed.•

DVI-D IN DVI EDID

DVI SIGNAL LEVEL

Press ◄► to switch “DVI EDID”.3.

The setting will change as follows each time • ◄► is pressed.

EDID1 EDID2(PC)

EDID1 (Input signal formats supported) :• Mainly select this when an external device (DVD player, etc.) for outputting video signals of a moving image system is connected to DVI-D IN.

EDID2 (Input signal formats supported) :• Mainly use this when an external device (PC, etc.) for outputting video signals of a still image system is connected to DVI-D IN.

Press ◄► to switch “DVI 4. SIGNAL LEVEL”.

The setting will change as follows each time • ◄► is pressed.

0-255:PC 16-235

0-255:PC:• Select this when, for example, an external device (PC, etc.) is connected via the DVI terminal output.

16-235:• Select this when, for example, an external device (DVD player, etc.) is connected via the HDMI terminal output using a conversion cable.

Note

The optimal setting differs depending on the output • setting of the connected external device. Refer to the instruction manual of the external device.

If the setting is changed, the data for plug and • play changes. For the plug and play compatible resolutions, check the compatible signal list (pp. 122-123).

EDID1

0-255:PC

Special Features

ENGLISH

– 73

Display Option settings (continued)

AUX DVI IN (Only when the ET-MD77DV is installed)

Change this setting if video does not display normally when the ET-MD77DV and an external device are connected via DVI-D.

Press ▲▼ to select “AUX DVI IN”.

DVI-D IN

AUX DVI IN

AUX SDI IN

Press ENTER.2.

The “AUX DVI IN” screen will be displayed.•

AUX DVI IN AUX DVI EDID

AUX DVI SIGNAL LEVEL

Press ◄► to switch “AUX DVI 3. EDID”.

The setting will change as follows each time • ◄► is pressed.

EDID1 EDID2(PC)

EDID1 (Input signal formats supported) :• Mainly select this when an external device (DVD player, etc.) for outputting video signals of a moving image system is connected to AUX DVI IN.

EDID2 (Input signal formats supported) :• Mainly use this when an external device (PC, etc.) for outputting video signals of a still image system is connected to AUX DVI IN.

Press ◄► to switch “AUX DVI 4. SIGNAL LEVEL”.

The setting will change as follows each time • ◄► is pressed.

0-255:PC 16-235

EDID1

0-255:PC

AUX SDI IN

Set this in accordance with the input module (sold separately).

Press ▲▼ to select “AUX SDI 1. IN”.

AUX DVI IN

AUX SDI IN

ON-SCREEN DISPLAY

Press ENTER.2.

The “AUX SDI IN” screen will be displayed.•

AUX SDI IN SDI LINK

BIT DEPTH(DUAL LINK) SDI SIGNAL LEVEL

Press ▲▼ to select the desired 3. item, and press ◄► to change the setting.

SDI LINK z

Select the single link signal type or dual link signal type. The setting will change as follows each time the button is pressed.

DUAL LINK

AUTO:• Selects the setting automatically.

SINGLE LINK:• Fixes the setting to signal link signal.

DUAL LINK:• Fixes the setting to dual link signal.

BIT DEPTH (DUAL LINK) z

Select the gradation for the signals to be input. This is only valid when dual link RGB input. The setting will change as follows each time the button is pressed.

AUTO AUTO

64-940

SINGLE LINKAUTO

74 –

0-255:PC :•

Select this when, for example, an external device (PC, etc.) is connected via the DVI terminal output.

16-235 :• Select this when, for example, an external device (DVD player, etc.) is connected via the HDMI terminal output using a conversion cable.

Note

The optimal setting differs depending on the output • setting of the connected external device. Refer to the instruction manual of the external device.

If the setting is changed, the data for plug and • play changes. For the plug and play compatible resolutions, check the compatible signal list (pp. 122-123).

ENGLISH

12-bitAUTO

10-bit

AUTO:• Selects 12-bit or 10-bit automatically.

12-bit:• Fixes the setting to 12-bit.

10-bit:• Fixes the setting to 10-bit.

SDI SIGNAL LEVEL z

Select the amplitude for the signals to be input. This is only valid when YP HD-SDI. The setting will change as follows each time the button is pressed.

64-940 4-1019

BPR and RGB input of

OSD DESIGN z

This sets the colour of the on-screen display (OSD).

64-940:• Normally set this.

4-1019:• Set this when gray appears black.

On-Screen display setting

The user can specify the on-screen display.

Press ▲▼ to select 1. “ON-SCREEN DISPLAY”.

AUX SDI IN

ON-SCREEN DISPLAY

BACK COLOR

Press ENTER.2.

The “ON-SCREEN DISPLAY” screen will be • displayed.

ON-SCREEN DISPLAY OSD POSITION

OSD DESIGN

Press ▲▼ to select the desired 3. item, and press ◄► to change the setting.

OSD POSITION z

This sets the position of the on-screen display (OSD).

BLACK

2 1

1• : Displayed in yellow.

2:• Displayed in blue.

3:• Displayed in white.

4:• Displayed in green.

5:• Displayed in pink.

6:• Displayed in brown.

OSD MEMORY z

This lets you save the cursor position in on-screen menus.

OFF ON

INPUT GUIDE z

This sets whether to display the currently selected input terminal name at the position set for “OSD POSITION”.

OFF ON

1 (Top left of the

screen)

9 (Bottom right of

the screen)

8 (Right centre of

the screen)

7 (Top right of the

screen)

2 (Left centre of the

screen)

3 (Bottom left of the

screen)

4 (Top centre of the

screen)

5 (Centre of the

screen)

6 (Bottom centre of

the screen)

WARNING MESSAGE z

This sets the display of warning messages.

OFF ON

Back Colour

This sets the colour for the projection screen when no signals are being input.

Press ▲▼ to select “BACK 1. COLOR”.

ON-SCREEN DISPLAY

BACK COLOR

STARTUP LOGO

BLACK LOGO3

ENGLISH

Special Features

– 75

Display Option settings (continued)

Press ◄► to switch “BACK 2. COLOR”.

The setting will change as follows each time • ◄► is pressed.

BLACK BLUE

LOGO3

BLACK: • The entire projection area will appear black.

BLUE:• The entire projection area will appear blue.

LOGO1:• The picture registered by the user will be projected in the projection area.

LOGO2:• The picture registered by the user will be projected in the projection area.

LOGO3:• The Panasonic logo is projected.

Note

Separate software is required in order to create the • pictures to use for “LOGO1” and “LOGO2”. Consult your dealer.

LOGO1

LOGO2

Note

Separate software is required in order to create the • pictures to use for “LOGO1” and “LOGO2”. Consult your dealer.

Setting the startup logo

This sets the startup logo that is projected when the power is turned on.

Press ▲▼ to select “STARTUP 1. LOGO”.

ON-SCREEN DISPLAY BACK COLOR

STARTUP LOGO

Press ◄► to switch “STARTUP 2. LOGO”.

The setting will change as follows each time • ◄► is pressed.

LOGO3

LOGO2

LOGO3:• The Panasonic logo and DIGITAL PROJECTOR logo are projected.

NONE:• No startup logo is projected.

LOGO1:• The picture registered by the user will be projected.

LOGO2:• The picture registered by the user will be projected.

BLACK LOGO3

NONE

LOGO1

76 –

ENGLISH

Projector setup

▲▼◄►

ENTER

Setting a projector ID

The projector has an ID number setting function that helps the user to control two or more projectors either simultaneously or separately with a single remote control. The ID number is set to “ALL” by default.

Hence the ID number need not be set when only one projector is used.

Press ▲▼ to select 1. “PROJECTOR ID”.

PROJECTOR SETUP PROJECTOR ID

INSTALLATION

Press ◄► to switch 2. “PROJECTOR ID”.

The setting will change as follows each time • ◄► is pressed.

ALL

FRONT-FLOOR

1/2

DEFAULT

This menu can be used to make a variety of picture and projector settings.

MAIN MENU

PICTURE POSITION ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION

PROJECTOR SETUP

P IN P TEST PATTERN SIGNAL LIST SECURITY NETWORK

Press to display the MAIN MENU screen.

Press to select “PROJECTOR SETUP”.

Press to display the “PROJECTOR SETUP” menu.

ALL

Press MENU twice.3.

This concludes the setting procedure and • the on-screen indications disappear and the normal screen appears again.

Note

The ID number can be set to “ALL”, or selected • from “1” to “64”.

If the projectors are given ID numbers, their remote • controls must be assigned the same ID numbers, respectively.

If the ID number of a projector is set to “ALL”, it can • be controlled by the remote control or the PC with any ID number. If multiple projectors are used and some of them have their IDs set to “ALL”, they cannot be controlled separately from the projectors with other ID numbers. For details on remote control ID setting, see page 18.

Special Features

MENU SELECT

ENTER

SUB MENU

ENGLISH

– 77

Projector setup (continued)

Installation Setting

A projection scheme can be chosen depending on the installation of the projector. If the picture is shown upside down or in reverse, change the projection scheme.

Select the setting by displaying the on-screen • indications using buttons of the remote control or the control panel on the main unit.

Press ▲▼ to select 1. “INSTALLATION”.

PROJECTOR ID

INSTALLATION

ALTITUDE MODE

Press ◄► to switch 2. “INSTALLATION”.

The setting will change as follows each time • ◄► is pressed.

FRONT-FLOOR

REAR-CELING

Floor mount front projection (FRONT-FLOOR)

FRONT-CELING

ALL

FRONT-FLOOR

REAR-FLOOR

Press MENU twice.3.

The on-screen indications disappear and the • normal screen appears again.

Altitude Mode

When using the projector over 1 400 m above sea level, set to “ON”.

Press ▲▼ to select “ALTITUDE 1. MODE”.

INSTALLATION

ALTITUDE MODE

DIRECTION

FRONT-FLOOR

HORIZONTAL

Press ◄► to switch “ALTITUDE 2. MODE”.

The setting will change as follows each time • ◄► is pressed.

OFF ON

Direction

The fan is controlled in accordance with the setup angle.

Ceiling mount front projection (FRONT-CEILING)

Floor mount rear projection (REAR-FLOOR)

Ceiling mount rear projection (REAR-CEILING)

Press ▲▼ to select 1. “DIRECTION”.

ALTITUDE MODE

DIRECTION

LAMP SELECT

HORIZONTAL

QUAD

Press ◄► to switch 2. “DIRECTION”.

The setting will change as follows each time • ◄► is pressed.

HORIZONTAL VERTICAL

HORIZONTAL:• This is the standard setup.

VERTICAL:• Select this if the projector is tilted at a large vertical angle (an angle which exceeds 30° from the horizontal).

78 –

ENGLISH

Lamp select

This lets you switch the four light source lamps to one of four brightnesses in accordance with the operating conditions and purpose of use.

Press ▲▼ to select “LAMP 1. SELECT”.

DIRECTION

LAMP SELECT

LAMP RELAY

Press ◄► to switch “LAMP 2. SELECT”.

The setting will change as follows each time • ◄► is pressed.

HORIZONTAL

QUAD

OFF

“L1/L3/L4” :• Three lamps illuminate. (Lamp units 1, 3 and 4 take priority.)

“L2/L3/L4” :• Three lamps illuminate. (Lamp units 2, 3 and 4 take priority.)

“SINGLE” :• One of the lamps illuminates. (The lamp unit with the shortest operating time is selected automatically.)

“DUAL” :• Two lamps illuminate. (The lamp units with the shortest operating time out of lamp units 1 and 4 or 2 and 3 are selected automatically.)

“TRIPLE” :• Three lamps illuminate. (The lamp unit with the shortest operating time is selected automatically.)

Press ENTER.3.

TRIPLE QUAD

DUAL L1

SINGLE L2

L2/L3/L4 L3

L1/L3/L4 L4

L1/L2/L4 L1/L4

L1/L2/L3 L2/L3

“QUAD” :• The four lamps illuminate. “L1” :• One lamp illuminates.

(Lamp unit 1 takes priority.) “L2” :• One lamp illuminates.

(Lamp unit 2 takes priority.) “L3” :• One lamp illuminates.

(Lamp unit 3 takes priority.) “L4” :• One lamp illuminates.

(Lamp unit 4 takes priority.) “L1/L4” :• Two lamps illuminate.

(Lamp unit 1 and 4 take priority.) “L2/L3” :• Two lamps illuminate.

(Lamp unit 2 and 3 take priority.) “L1/L2/L3” :• Three lamps illuminate.

(Lamp units 1, 2 and 3 take priority.) “L1/L2/L4” :• Three lamps illuminate.

(Lamp units 1, 2 and 4 take priority.)

Note

For settings other than “QUAD”, any lamp which is • malfunctioning or which has a cumulative operating time that exceeds 2 000 hours will be turned off and the other lamps will be turned on. If “QUAD” is selected, any lamp which is malfunctioning or which has a cumulative operating time that exceeds 2 000 hours will be turned off and only the lamps which have a cumulative operating time of less than 2 000 hours will be turned on. In addition, if the cumulative operating times for all lamps exceed 2 000 hours, the projector will switch to standby mode.

Lamp units which are not turned on should still be • installed to the projector.

When it is time to replace the lamp, the number of • the lamps that illuminate will be greater than the specified number of lamps in order to prevent the luminance from dropping.

The characters in the lamp selection menu • will become green when they are selected. Furthermore, the characters may flash depending on the condition of the lamps. Yellow: An error has occurred with the

illumination of one or more of the lamps White: Unselected item Red: Lamp where an illumination error has

occurred

Special Features

ENGLISH

– 79

Projector setup (continued)

Lamp relay

If using the projector for a continuous period of 24 hours or more, this setting can be used to automatically switch the lamps that are turned on in order to reduce the lamp deterioration that can occur as a result of continuous use.

“LAMP RELAY” will only be enabled when the lamp • selection is “SINGLE” (1 lamp), “DUAL” (2 lamps), “TRIPLE” (3 lamps) or “QUAD” (4 lamps).

Press ▲▼ to select “LAMP 1. RELAY”.

LAMP SELECT

LAMP RELAY

RS-232C

Press ◄► to switch “LAMP 2. RELAY”.

The time interval for lamps to be switched will • change as shown in the diagram below each time ◄► is pressed.

(Units of 1 hour)

23:00

QUAD

OFF

00:00OFF

01:00

Press ENTER.2.

The “RS-232C” screen will be displayed.•

RS-232C SERIAL IN

(IN) BAUDRATE (IN) PARITY (OUT) BAUDRATE (OUT) PARITY RESPONSE(ID ALL) GROUP RESPONSE(ID GROUP)

RS-232C

9600 NONE 9600 NONE

MASTER

Press ▲▼ to select “SERIAL IN”.3.

Press ◄► to switch “SERIAL 4. IN”.

The setting will change as follows each time • ◄► is pressed.

RS-232C RS-422

Press ▲▼ to select 5. communication conditions.

Press ◄► to confirm the setting.6.

Note

The lamps will switch at the specified time when the • lamp selection is “SINGLE” or “DUAL”.

When the lamp selection is “TRIPLE”, the lamps will • switch a total of three times at two-hour intervals starting from the specified time, and after this the previous operating status will be maintained until the next specified time is reached.

When the lamp selection is “QUAD”, three lamps • will illuminate from the specified time, and the three lamps will switch a total of four times at two-hour intervals from that time. After this, four lamps will illuminate for eight hours from the specified time, and then when the next specified time is reached, switching between three lamps will resume.

The setting time will be the local time. (p. 83)•

RS-232C setting

This sets communication parameters for the projector. (p. 106)

Press ▲▼ to select “RS-232C”.1.

LAMP RELAY

RS-232C

REMOTE2 MODE

OFF

DEFAULT

Press MENU three times.7.

The on-screen indications disappear, and the • system returns to the normal screen.

Remote2 mode

This sets the REMOTE2 terminal. (p. 110)

Press ▲▼ to select “REMOTE2 1. MODE”.

RS-232C

REMOTE2 MODE

STATUS

Press ◄► to switch “REMOTE2 2. MODE”.

The setting will change as follows each time • ◄► is pressed.

DEFAULT USER

DEFAULT:• The pin assignment of the REMOTE2 terminal is used as the projector default setting. (p. 110)

USER:• This is used for changing an optional input module, using the REMOTE2 terminal, or for changing the settings for the REMOTE2 terminal. Any settings you make for pins 2 to 8 become valid once you press the ENTER button.

DEFAULT

80 –

ENGLISH

Status

Displays the status of the projector.

Press ▲▼ to select “STATUS”.1.

REMOTE2 MODE

STATUS

AIR FILTER CLEANING

Press ENTER.2.

The “STATUS” screen will be displayed.•

STATUS

INPUT NAME SIGNAL FREQUENCY PROJECTOR RUNTIME LAMP1 LAMP2 LAMP3 LAMP4 INTAKE AIR TEMP. OPTICS MODULE TEMP. AROUND LAMP TEMP. REMOTE2 STATUS

Press ◄► to move to the next 3. page.

STATUS

PROJECTOR MODEL SERIAL NUMBER MAIN VERSION SUB VERSION NETWORK VERSION

Press ◄► to move to the next 4. page.

STATUS

ON COUNT

POWER ON TIMES LAMP1 ON LAMP2 ON LAMP3 ON LAMP4 ON SHUTTER

AIR FILTER CLEANING AUX NUMBER OF ENTRY SIGNAL AC VOLTAGE

INPUT:• Displays the input selection state.

NAME:• Displays the input signal name.

SIGNAL FREQUENCY:• Displays the frequency of the input signal.

PROJECTOR RUNTIME:• Displays the projector runtime.

LAMP1:• Displays the lighting time of LAMP1.

LAMP2:• Displays the lighting time of LAMP2.

LAMP3:• Displays the lighting time of LAMP3.

XGA60-A399999

48.36kHz/59.99Hz

341h / ON / 334h / ON / 342h / ON /

97h / ON /

31°C/87°F 27°C/80°F 31°C/87°F

MD77SD1:SN

DEFAULT

RGB2

76h

DISABLE

DZ12000 SWXXXXX

1.00.00

0.04

1.01

8 362 363 366 116

0( 6) 1( 1)

0/96

NORMAL

1/3

2/3

3/3

LAMP4:• Displays the lighting time of LAMP4.

INTAKE AIR TEMP:• Displays the intake air temperature of the projector.

OPTICS MODULE TEMP.:• Displays the temperature inside the projector.

AROUND LAMP TEMP.:• Displays the temperature around the lamp of the projector.

REMOTE2 STATUS:• Displays the control status of REMOTE2.

PROJECTOR MODEL:• Displays the type of projector.

SERIAL NUMBER:• Displays the serial number of the projector.

MAIN VERSION:• Displays the main version of the firmware of the projector unit.

SUB VERSION:• Displays the sub version of the firmware of the projector unit.

NETWORK VERSION:• Displays the network version of the projector unit.

ON COUNT:•

POWER ON TIMES:

Displays the number of times the power has been turned on.

LAMP1 ON:

Displays the number of times LAMP1 has been lit.

LAMP2 ON:

Displays the number of times LAMP2 has been lit.

LAMP3 ON:

Displays the number of times LAMP3 has been lit.

LAMP4 ON:

Displays the number of times LAMP4 has been lit.

SHUTTER:

Displays the number of times the shutter function has been used.

AIR FILTER CLEANING:

Displays the number of times the air filter has

been cleaned. AUX:• Displays the name of the optional input module inserted in the input module.

NUMBER OF ENTRY SIGNAL:• Displays the number of registered signals.

AC VOLTAGE:• Displays the AC voltage state.

Cleaning the air filter

This can be used to set air filter cleaning.

Press ▲▼ to select “AIR FILTER 1.

CLEANING”.

STATUS

AIR FILTER CLEANING

AUTO POWER OFF

DISABLE

Special Features

ENGLISH

– 81

Projector setup (continued)

Press ENTER.2.

The “AIR FILTER CLEANING” screen will be • displayed.

You can select the automatic cleaning time • (“TIME”) and also force cleaning to be carried out immediately (“EXECUTE”).

AIR FILTER CLEANING TIME

EXECUTE

00:00

Press ▲▼ to select “TIME”.3.

Select “TIME” and then set the time for • automatic cleaning to be carried out.

If you would like cleaning to be carried out • straight away, select “EXECUTE” and then press ENTER.

Press ◄► to switch “TIME”.4.

The setting will change as follows each time • ◄► is pressed.

00:00 23:50

(in units of 10 minutes)

The default setting is “00:00” (midnight).•

Example: When the default setting is in use,

automatic cleaning will start at 00:00 if the projector is in projection mode. If the time is set to 7:00, automatic cleaning will start at that time if the projector is in projection mode.

Note

Contaminants such as oil and cigarette tar cannot • be cleaned when air filter cleaning is carried out.

The air filter cleaning monitor (FILTER CLEANING) • will flash blue while cleaning of the air filter is in progress. If there is a problem with the air filter, the air filter cleaning monitor (FILTER CLEANING) will light red.

The time taken for cleaning is approximately 30 to • 40 seconds.

The setting time will be the local time. (p. 83)• If the projector is not in projection mode when the •

setting time is reached, automatic cleaning will not be carried out.

Automatic cleaning will not be carried out if 24 • hours have not yet elapsed since cleaning was last carried out (either by automatic cleaning or forced cleaning).

Example: If the setting time is 7:00 and forced

cleaning is carried out at 9:00, then automatic cleaning will not be carried out at 7:00 on the following day.

46 hours elapsed

22 hours elapsed

Setting time Setting time Setting time

Automatic cleaning

If the time is set to a time which is within 24 • hours from the last time cleaning was carried out, automatic cleaning will not be carried out the next time the setting time is reached. Instead, cleaning will be carried out when the setting time is reached on the following day.

Example: If cleaning was carried out at 10:00, and

Setting time Setting time Setting time

Automatic cleaning

When projection starts (when the power is • turned on), automatic cleaning will be carried out immediately if more than 24 hours have elapsed since cleaning was last carried out.

Forced cleaning

the cleaning time setting is then changed to 20:00, automatic cleaning will be carried out at 20:00 on the following day.

10 hours elapsed

Time reset

(No cleaning) Automatic

34 hours elapsed

(No cleaning)

cleaning

Automatic cleaning

Auto power off

The projector can be set to automatically enter the standby state if no signal is input before the set time elapses.

Press ▲▼ to select “AUTO 1. POWER OFF”.

AIR FILTER CLEANING

AUTO POWER OFF

FUNC1

Press ◄► to switch “AUTO 2. POWER OFF”.

The setting will change as follows each time • ◄► is pressed.

DISABLE

82 –

ENGLISH

DISABLE 45MIN.

90MIN.

60MIN.

75MIN.

Setting FUNC1

The user can specify the function of the “FUNC1” button on the remote control.

Press ▲▼ to select “FUNC1”.1.

AIR FILTER CLEANING AUTO POWER OFF

FUNC1

Press ENTER.2.

The “FUNC1” screen will be displayed.•

FUNC1

DISABLE

P IN P

Press ▲▼ to select a function.3.

DISABLE:•

Disables the FUNC1 button. P IN P:•

Enables setting of P IN P to “OFF”, “USER 1”, “USER 2”, or “USER 3”. (pp. 85-86)

SUB MEMORY:• The sub memory can be switched. (pp. 46-47)

SYSTEM SELECTOR:• Allows the system selector to be switched. (pp. 58-59)

SYSTEM DAYLIGHT VIEW:• Allows the system daylight view to be switched. (pp. 56-57)

FREEZE:• Allows switching to freeze mode for temporarily stopping video.

Press ENTER.4.

DISABLE

Press ◄► to switch “TIME 4.

ZONE”.

Press ▲▼ to select “ADJUST 5.

CLOCK”.

Press ENTER.6.

The “ADJUST CLOCK” screen will be • displayed.

ADJUST CLOCK YEAR

MONTH DAY HOUR MINUTE APPLY

2008

2 13 15

Press ▲▼ to select the item to 7. be set, and use ◄► to set the local time.

Use ▲▼ to select “APPLY”, and 8. then press ENTER.

This completes setting of the time. •

Save all user data

This saves various setting values as a backup to the internal memory of the projector.

Press ▲▼ to select “SAVE ALL 1. USER DATA”.

DATE AND TIME

SAVE ALL USER DATA

LOAD ALL USER DATA

Setting the date and time

This lets you set the time zone and the current date and time for the projector’s internal clock.

Press ▲▼ to select “DATE AND 1. TIME”.

PROJECTOR SETUP DATE AND TIME

SAVE ALL USER DATA

Press ENTER.2.

The “DATE AND TIME” screen will be • displayed.

DATE AND TIME TIME ZONE

ADJUST CLOCK LOCAL DATE LOCAL TIME

Press ▲▼ to select “TIME 3. ZONE”.

09:00

2008/01/01

12:34:56

2/2

Press ENTER.2.

The “SECURITY PASSWORD” screen will be • displayed.

SECURITY PASSWORD

Enter the password set for 3. the security password of the security menu.

A confirmation screen will appear.•

SAVE ALL USER DATA?

OK CANCEL

CHANGE

ENTER

EXECUTE

Press ◄► to select “OK”, and 4. press ENTER.

Note

“NETWORK/E-MAIL” and “LOGO IMAGE” are not • saved.

Special Features

PROGRESS

ENGLISH

– 83

Projector setup (continued)

Load all user data

This loads various setting values that were saved as a backup to the internal memory of the projector.

Press ▲▼ to select “LOAD ALL 1. USER DATA”.

SAVE ALL USER DATA

LOAD ALL USER DATA

INITIALIZE

Press ENTER.2.

The “SECURITY PASSWORD” screen will be • displayed.

SECURITY PASSWORD

Enter the password set for 3. the security password of the security menu.

A confirmation screen will appear.•

LOAD ALL USER DATA?

After data has been loaded, power will turn off automatically. Please wait for the fan to finish cooling before you turn on the projector again.

OK CANCEL

CHANGE

ENTER

EXECUTE

PROGRESS

Enter the password set for 3. the security password of the security menu.

The “INITIALIZE” screen will be displayed.•

INITIALIZE

ALL USER DATA ENTRY SIGNAL

NETWORK/E-MAIL

LOGO IMAGE

ALL USER DATA:• This is for use by service personnel. All setting values including “ENTRY SIGNAL”, “NETWORK/E-MAIL”, and “LOGO IMAGE” are returned to their factory default values. A restart will be required to complete the initialization of ALL USER DATA.

ENTRY SIGNAL:• All setting values saved for each of the input signals are cleared. To clear just some registered signals, perform the procedure described in “Clearing the data of registered signals”. (p. 46)

NETWORK/E-MAIL:• This returns “NETWORK/E-MAIL” to its factory default value.

LOGO IMAGE:• The settings for the images registered for LOGO1 and LOGO2 are returned to their factory default images. (p. 76)

Press ◄► to select “OK”, and 4. press ENTER.

Note

If this is executed, the projector enters a standby • state in order to reflect the setting values.

Initialize

This returns various setting values to their factory default settings.

Press ▲▼ to select 1. “INITIALIZE”.

LOAD ALL USER DATA

INITIALIZE

SERVICE PASSWORD

Press ENTER.2.

The “SECURITY PASSWORD” screen will be • displayed.

SECURITY PASSWORD

Press ▲▼ to select the desired 4. initialize item, and press ENTER.

A confirmation screen will appear.•

INITIALIZE NETWORK/E-MAIL?

OK CANCEL

CHANGE

ENTER

SET

PROGRESS

Press ◄► to select “OK”, and 5. press ENTER.

Service password

This function is used by a service person. Input the password with the numeric buttons (0 to 9) of the remote control and press ENTER to confirm the entry.

84 –

ENGLISH

P IN P

▲▼◄►

ENTER

Using the P IN P function

Two videos can be projected simultaneously by placing a separate small sub screen within the main screen.

Press ENTER.1.

The “P IN P” screen will be displayed.•

P IN P P IN P MODE

Press ▲▼ to select “P IN P 2. MODE”.

P IN P MODE

OFF

USER1

USER2 USER3

Press ▲▼ to select a function.3.

OFF:•

The P IN P function is not used. USER1, USER2, USER3:•

The P IN P function is used with the settings that were set in “Setting the P IN P function”.

OFF

This item is used to set the condition of the Picture-In-Picture.

Press to display the MAIN MENU screen.

Press to select “P IN P”.

Press to display the “P IN P” menu.

MAIN MENU

PICTURE POSITION ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION PROJECTOR SETUP

P IN P

TEST PATTERN SIGNAL LIST SECURITY NETWORK

MENU SELECT

ENTER

SUB MENU

Press ENTER.4.

Setting the P IN P function

The settings of the P IN P function can be saved to “USER1”, “USER2”, and “USER3”.

Refer to “Using the P IN P 1. function” above, and then select from “USER1”, “USER2”, and “USER3”.

The settings for the user data selected for “P IN • P MODE” are displayed.

P IN P

P IN P MODE

MAIN WINDOW

SIZE POSITION SUB WINDOW SIZE POSITION

FRAME LOCK

TYPE

Press ▲▼ to select the desired 2. setting item, and press ENTER.

The sub menu for the selected item appears.•

USER1 VIDEO

RGB2

MAIN WINDOW

SUB WINDOW

Special Features

ENGLISH

– 85

P IN P (continued)

MAIN WINDOW:•

The input terminal for the main window is displayed. Press ▲▼ to select an item, and press ENTER to switch to the item. SIZE: The user can specify the display size of the main window between 10 % and 100 %. POSITION: The user can specify the display position of the main window on the screen.

SUB WINDOW:• The input terminal for the SUB WINDOW is displayed. Press ▲▼ to select an item, and press ENTER to switch to the item. SIZE: The user can specify the display size of the subwindow between 10 % and 100 %. POSITION: The user can specify the display position of the subwindow on the screen.

FRAME LOCK:• The user can select the window to apply frame lock. Press ◄► to switch windows. “MAIN WINDOW”: Frame lock is set for the input signals specified for the main window. “SUB WINDOW”: Frame lock is set for the input signals specified for the subwindow.

TYPE:• The user can select the window that is displayed by priority when two windows overlap. Press ◄► to switch windows. “MAIN WINDOW”: The main window is displayed by priority. “SUB WINDOW”: The subwindow is displayed by priority.

Note

The P IN P function is not available depending on • the input signals and the selected input terminals. Refer to “List of P IN P” for details. (p. 124)

The main window’s picture adjustment values such • as the picture mode, gamma selection and colour temperature setting for the main window will be applied.

In the normal screen (when the menu is not • displayed), the ◄► buttons can be used to switch the size and position of the main window and subwindow when the P IN P function is on.

86 –

ENGLISH

Displaying the internal test pattern

Test pattern

Results of adjustment on the image, picture quality, position, size and other factors will not be reflected in test patterns. Be sure to display the input signal before performing various kinds of setting.

Press ◄► to search through the 1.

various types of test patterns.

▲▼◄►

ENTER

The projector has 8 types of internal test patterns to check the condition of the set.

Press to display the MAIN MENU screen.

Cycle of displayed internal test



patterns

The setting will change as follows each time ◄► is pressed.

MENU screen

Focus

MENU screen

Colour bars

MENU screen

Window (inversion)

MENU screen

Entry screen

MENU screen

All white

MENU screen

All black

MENU screen

Flag

MAIN MENU

PICTURE POSITION ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION PROJECTOR SETUP P IN P

TEST PATTERN

SIGNAL LIST SECURITY NETWORK

MENU SELECT

ENTER

SUB MENU

Press to select “TEST PATTERN”.

Press to display the “TEST PATTERN” screen.

MENU screen

Window

MENU screen

Flag (inversion)

Special Features

ENGLISH

– 87

Setting the security

Displaying the security screen

Password settings and text settings can be made after the security screen is displayed.

If using for the first time z

▲▼◄►

ENTER

The unit’s security function serves to display the password input screen or to set and display the user company’s URL under the projected pictures.

MAIN MENU

PICTURE POSITION ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION PROJECTOR SETUP P IN P TEST PATTERN SIGNAL LIST

SECURITY

NETWORK

MENU SELECT

ENTER

SUB MENU

Press to display the MAIN MENU screen.

Press to select “SECURITY”.

Press to display the “SECURITY” menu.

Press ▲, ►, ▼, ◄, ▲, ►, ▼ and 1. ◄ in this order.

If the existing password has been changed z

Enter the new password.

SECURITY PASSWORD

󲄃󲄃󲄃󲄃󲄃󲄃󲄃󲄃

Press ENTER.2.

The “SECURITY” screen will be displayed.•

Note

Only asterisks • represent the actual characters of the password when the password is entered.

will appear on the screen to

Setting the security password

The SECURITY PASSWORD screen can be displayed when the power has been turned on. If the correct password is not entered, operations other than using the POWER STANDBY ( ) button and SHUTTER button and adjusting the lens will not be possible.

Press ▲▼ to select “SECURITY 1. PASSWORD”.

SECURITY SECURITY PASSWORD

SECURITY PASSWORD CHANGE

Press ◄► to switch “SECURITY 2. PASSWORD”.

The setting will change as follows each time • ◄► is pressed.

OFF ON

ON:• Password entry is enabled.

OFF:• Password entry is disabled.

OFF

88 –

ENGLISH

Changing the security password

The password can be changed.

Press ▲▼ to select “SECURITY 1. PASSWORD CHANGE”.

SECURITY PASSWORD

SECURITY PASSWORD CHANGE

DISPLAY SETTING

OFF

OFF:• The text display is disabled.

TEXT:• The text display is enabled.

LOGO1:• The picture registered by the user will be projected.

LOGO2:• The picture registered by the user will be projected.

LOGO3:• The Panasonic logo is projected.

Press ENTER.2.

The “SECURITY PASSWORD CHANGE” screen • will be displayed.

SECURITY PASSWORD CHANGE NEW

CONFIRM

Press ▲▼◄► to set the 3. password.

Up to 8 buttons can be set as the password.•

Press ENTER.4.

For the purposes of 5. confirmation, enter the password again.

Press ENTER.6.

Note

Only asterisks * will appear on the screen to • represent the actual characters of the password when the password is entered.

Setting the text

The set text can be permanently displayed below the pictures being projected.

Press ▲▼ to select “DISPLAY 1. SETTING”.

SECURITY PASSWORD CHANGE

DISPLAY SETTING

TEXT CHANGE

Press ◄► to switch “DISPLAY 2. SETTING”.

The setting will change as follows each time • ◄► is pressed.

OFF

Note

Separate software is required in order to create the • pictures to use for “LOGO1” and “LOGO2”. Consult your dealer.

Changing the text

When DISPLAY SETTING is enabled, you can change the text that is displayed.

Press ▲▼ to select “TEXT 1. CHANGE”.

DISPLAY SETTING

TEXT CHANGE

CONTROL DEVICE SETUP

Press ENTER.2.

The “TEXT CHANGE” screen will be displayed.•

TEXT CHANGE

SELECT

ABCDEFGHIJKLMNO

PQRSTUVWXYZ;:,.

abcdefghijklmno

pqrstuvwxyz/+-*

0123456789 _@[]

< > BS OK CANCEL

Press ◄► to select the text 3. position, and press ▲▼ to select the characters of the text.

Press ENTER.4.

The text is now changed.•

OFF

Special Features

OFF TEXT

LOGO3

LOGO2

LOGO1

ENGLISH

– 89

Setting the security (continued)

Control device setup

Control from the remote control and main unit controls can be restricted.

Press ▲▼ to select “CONTROL 1. DEVICE SETUP”.

DISPLAY SETTING TEXT CHANGE

CONTROL DEVICE SETUP

Press ENTER.2.

The “CONTROL DEVICE SETUP” screen will be • displayed.

CONTROL DEVICE SETUP CONTROL PANEL

REMOTE CONTROLLER

Press ▲▼ to select “CONTROL 3. PANEL” or “REMOTE CONTROLLER”.

CONTROL PANEL:•

Restriction of control from the main unit controls can be set.

ENABLE:• Enables control from the main unit controls.

DISABLE:• Disables control from the main unit controls.

REMOTE CONTROLLER:• Restriction of control from the remote control can be set.

ENABLE:• Enables control from the remote control.

DISABLE:• Disables control from the remote control.

OFF

Note

If a setting is reflected, the on-screen menu • disappears. To continue operation, press the MENU button to display the main menu.

If an attempt is made to control the projector from • the remote control or main unit controls when “ENABLE” is set, the security password screen appears. To change a setting, enter the security password and change the operation setting. The security password screen disappears if the MENU button is pressed or no operation is performed for 10 seconds.

90 –

Press ENTER.4.

The “CONTROL PANEL” or “REMOTE • CONTROLLER” screen will be displayed.

CONTROL PANEL

ENABLE

DISABLE

Press ▲▼ to select “ENABLE” 5. or “DISABLE”, and then press ENTER.

A confirmation screen will appear.•

SURE?

EXECUTE CANCEL

CHANGE

ENTER

EXECUTE

Press ◄► to select “EXECUTE”, 6. and then press ENTER.

ENGLISH

How to use network function

Network standby

When the projector is in a standby state, you can control the power of the projector from a computer connected via a wired LAN.

Press ▲▼ to select “NETWORK 1.

▲▼◄►

ENTER

STANDBY”.

NETWORK NETWORK STANDBY

NETWORK SETUP

Press ◄► to switch “NETWORK 2. STANDBY”.

The setting will change as follows each time • ◄► is pressed.

OFF ON

OFF

This allows you to use network functions.

MAIN MENU

PICTURE POSITION ADVANCED MENU DISPLAY LANGUAGE DISPLAY OPTION PROJECTOR SETUP P IN P TEST PATTERN SIGNAL LIST SECURITY

NETWORK

MENU SELECT

ENTER

SUB MENU

Press to display the MAIN MENU screen.

Press to select “NETWORK”.

Press to display the “NETWORK” menu.

DEFAULT

ON:• Enables the network standby function.

OFF:• Disables the network standby function.

Initial setting of network function

Make the initial network function settings before using the network functions.

Press ▲▼ to select “NETWORK 1. SETUP”.

NETWORK STANDBY

NETWORK SETUP

NETWORK CONTROL

Press ENTER.2.

The “NETWORK SETUP” screen will be • displayed.

NETWORK SETUP HOST NAME

DHCP IP ADDRESS SUBNET MASK GATEWAY STORE

Press ▲▼ to select items, and 3. press ENTER to change the setting.

HOST NAME (Display of host name and • setting) :

Make alteration when to use the DHCP server.

OFF

PROJECTOR

OFF

192. 168. 0. 8

255. 255. 255. 0

192. 168. 0. 1

Special Features

ENGLISH

– 91

How to use network function (continued)

DHCP (DHCP client function) :•

Set the DHCP item to ON when to acquire an IP address automatically using the DHCP server. Set to OFF if DHCP server is not used. Enter the IP address if DHCP server is not used.

IP ADDRESS (Display of IP address and • setting) :

Enter the IP address if DHCP server is not used.

SUBNET MASK (Displaying and setting the • subnet mask) :

If not using a DHCP server, enter the subnet mask.

GATEWAY (Display of gateway address and • setting) :

Enter the gateway address if DHCP server is not used.

STORE:• Save the current network settings.

Press ▲▼ to select “STORE”, 4. and then press ENTER.

Note

Before using the DHCP server, make sure the DHCP • server is already functioning.

For details of IP address, subnet mask, and • gateway, ask the network administrator.

WEB CONTROL:• Set this to ON when you want to perform control with the Web browser. (pp. 93-104)

WEB PORT:• Set the port number to use.

PJLink CONTROL:• Set this to ON when you want to perform control with the PJLink protocol. (p. 105)

COMMAND CONTROL:• Set to ON to control using the control command via the serial terminal. (pp.106-109) If settings have been made without an administrator password of the Web browser control, add 2-byte “00” instead of STX, and a line-feed code (0Dh) instead of ETX. If settings have been made with an administrator password of the Web browser control, add a 32-byte hash value and “00” instead of STX and a line-feed code (0Dh) instead of ETX. The hash value is created by MD5 combining “admin1:”, password, “:” and random numbers. The random numbers are 8-byte values sent from the projector when connecting.

COMMAND PORT:• Set the port number used for the command control.

STORE:• Save the current network control settings.

Network status

Network control

This sets the network control method.

Press ▲▼ to select “NETWORK 1. CONTROL”.

NETWORK SETUP

NETWORK CONTROL

NETWORK STATUS

Press ENTER.2.

The “NETWORK CONTROL” screen will be • displayed.

NETWORK CONTROL WEB CONTROL

WEB PORT PJLink CONTROL COMMAND CONTROL COMMAND PORT STORE

Press ▲▼ to select items, and 3. press ◄► to change the setting.

80 OFF OFF

1024

This displays the network status of the main unit.

Press ▲▼ to select “NETWORK 1. STATUS”.

NETWORK SETUP NETWORK CONTROL

NETWORK STATUS

Press ENTER.2.

The “NETWORK STATUS” screen will be • displayed.

NETWORK STATUS

DHCP IP ADDRESS SUBNET MASK GATEWAY DNS1 DNS2 MAC ADDRESS

192. 168. 0. 8

255. 255. 255. 0

192. 168. 0. 1

0. 0. 0. 200

0. 0. 0. 0

OFF

00:0B:97:41:03:05

Returning the network function setting back to the factory setting

Network function settings such as the IP address, password, and e-mail settings can be return to their factory settings with the initialize menu of the projector setup. (p. 84)

92 –

ENGLISH

Network connections

The projector is equipped with network functions, and web browser controls can be used to carry out the following operations from a computer.

Projector settings and adjustments• Projector status display• Transmission of E-mail messages if there is a problem with the projector•

Note

A LAN cable is required to use the network function.•

Projector

LAN cable (straight) LAN cable (straight)

A Web browser is required to use this function. Make sure that a Web browser is available in the system.• Use Microsoft Windows 98SE/Me/NT4.0/2000/XP/Vista for the OS of your personal computer.• The Web browser should be Internet Explorer 6.0 or later or Netscape Communicator 7.0 or later.• To use the E-mail function, communication with E-mail server must be established. Make sure that E-mail •

feature is available in your system. Use a straight insulated LAN cable which supports category 5 or above.• The length of LAN cable must be 100 m or shorter.•

Name and function of network function parts



IN OUT

OUT

VIDEO RGB 2 IN

S-VIDEO IN

RS-232C IN RS-422 IN

G/YR/P

SYNC/HD VD

RGB 1 IN

B/P

SERIALREMOTE 1 REMOTE 2 IN

RS-422 OUT

LAN

DVI-D IN

LAN terminal (10BASE-T/100BASE-TX)

Connect LAN cable here.

Special Features

LAN LINK/ACT lamp (green)

This lights when a LAN cable is connected and flashes when signals are being received or sent.

LAN10/100 lamp (yellow)

This lights when a 100BASE-TX connection is established.

Attention

If the LAN terminal is touched by electrostatically charged hands (or body), failure may be caused by the • discharge of static electricity. Be careful not to touch metallic part of LAN terminal or LAN cable.

Connect indoor equipment to the LAN.•

ENGLISH

– 93

How to use network function (continued)

Accessing from the Web browser

Activate the Web browser in the personal computer.1.

Enter the IP address set by the projector into the URL input field of the 2. Web browser.

Enter your “User Name” and “Password”.3.

The factory default settings are user1 (user privileges) or admin1 (administrator privileges) for the user name • and panasonic (lowercase letters) for the password.

Press OK to display the Projector status page.4.

Note

Avoid activating two or more Web browser simultaneously to work out setting or control actions.• Change the password first of all.• Administrator privileges enable the use of all functions. User privileges enable the use of only “Projector status”, •

“Error information”, “Network status”, “Basic control”, and “Change password”. If the password is incorrectly entered three times in a row, the lock is set for several minutes.•

Change Password page



Click [Change password].

94 –

Old password input field

New password input field

New password input field (re-enter for confirmation) Button for executing password change

When you log in with administrator privileges, the button for resetting the password for user privileges is displayed.

ENGLISH

Basic control page



This page is the first page displayed when the projector is accessed through a web browser. To move from another page, click [Projector control], then [Basic control].

Page selection tabs

Click these to switch pages.

This displays the on-screen status. It is displayed even if the on-screen display of the projector is set to off.

Monitor information button

Click this item, and the status of the projector is displayed.

Detailed set up button

Click this item to display the advanced settings page.

Change password button

Power On/Off control

SHUTTER control

OSD (On-screen Display) display/ non-display

System type switching

Use these to select the input signals.

Special Features

ENGLISH

– 95

How to use network function (continued)

Detail control page



Click [Projector control], then [Detail control] to display the Detail control page.

Pressing these buttons controls the projector and updates the on-screen description on the right of the control page when control is finished.

Lens adjustment

Test pattern display

This button updates the on-screen description on the right of the control page with the latest information.

Menu display

Projector status page



Click [Status], then [Projector status] to display the Status information page. This page displays the projector statuses established for the items shown below.

Displays the firmware version of the projector main unit.

Displays the type of projector.

Displays the input switching status.

Displays temperature of projector’s intake air.

Displays temperature inside the projector.

Displays temperature of projector exhaust.

96 –

Displays the lamp lit hours.

Displays self-diagnosis information.

Displays used hours of the projector.

ENGLISH

Error information page



When is displayed on the status information screen, click it to display the error details.

Depending on the nature of the error, the projector may be placed in the standby mode for its own • protection.

OK: Normal operation FAILED: Occurrence of trouble

When [FAILED] has appeared for an item z

Parameter Description

MAIN CPU BUS Trouble has occurred in the microcomputer circuitry. Consult your dealer. FAN Trouble has occurred in the fan or its drive circuit. Consult your dealer.

The temperature inside the projector is high. It may be that the projector is

OPTICS MODULE TEMPERATURE

INPUT AIR TEMPERATURE

OUTPUT AIR TEMPERATURE

LAMP REMAIN TIME

LAMP STATUS

APERTURE (CONTRAST-SHUTTER)

SHUTTER (MUTE-SHUTTER)

DIRTY AIR FILTER

AIR FILTER CLEANER UNIT The air filter unit is not installed. Install the air filter unit.

OPTICS MODULE TEMP.SENSOR

INPUT AIR TEMP.SENSOR

OUTPUT TEMP. SENSOR

BATTERY The backup battery has been run out. Consult your dealer. CLOGGED FILTER SENSOR Problem with clogged filter sensor. Consult your dealer.

AC POWER

LENS SHIFT Problem with lens shift circuit. Consult your dealer.

being used in an operating environment where the temperature is high such as near a heating appliance.

The input air temperature is too high. It may be that the projector is being used in an operating environment where the temperature is high such as near a heating appliance.

The temperature around the lamp is too high. It may be that the projector’s ventilation holes are blocked.

The lamp runtime has exceeded the prescribed cumulative time, and it is now time to replace the lamp.

The lamp has failed to light. Wait a short while for the lamp to cool off, and then turn on the power.

Trouble has occurred in the contrast shutter circuitry. Consult your dealer.

Trouble has occurred in the shutter circuitry. Consult your dealer.

The air filter is blocked with dust. Turn off the MAIN POWER switch by following the procedure on page 39, and then clean the air filter. (pp. 112-113)

Trouble has occurred in the temperature detection sensor inside the projector. Consult your dealer.

Trouble has occurred in the sensor used to detect the input air temperature. Consult your dealer.

Trouble has occurred in the sensor used to detect the exhaust air temperature. Consult your dealer.

AC power supply voltage input has dropped. Check that there is sufficient electrical wiring capacity for the projector’s power consumption requirements.

Special Features

ENGLISH

– 97

How to use network function (continued)

E-mail setup page



With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can be sent to one or more preset e-mail addresses (maximum two addresses). Click [Detailed set up], then [E-mail set up] to display the E-mail setup page.

Select “Enable” to use the E-mail function. Enter the IP address or server name of the

E-mail server (SMTP). The DNS server must be set if the server name is entered.

Enter the E-mail address of the projector. (maximum 63 characters)

The user can enter the location of, for example, the installed projector so that the recipient may easily identify the originator of the E-mail. (maximum 63 characters)

The user can modify the minimum time interval of temperature warning mail. The default value is 60 minutes. In this case, the user cannot send another mail for 60 minutes after sending previous temperature warning mail even the set warning temperature is reached again. The user can modify the threshold temperature for sending temperature warning mail. If the temperature rises above the set value, control sends temperature warning mail.

Enter the E-mail address of your desired recipient.

Select the conditions for sending E-mail.

MAIL CONTENTS:

Select “NORMAL” or “SIMPLE”.

ERROR:

an error is detected by self-diagnosis.

LAMP1 RUNTIME:

remaining lamp service time has reached the value set in the field.

LAMP2 RUNTIME:

remaining lamp service time has reached the value set in the field.

LAMP3 RUNTIME:

remaining lamp service time has reached the value set in the field.

LAMP4 RUNTIME:

remaining lamp service time has reached the value set in the field.

INPUT AIR TEMPERATURE:

intake air temperature has reached the value set in the field.

OUTPUT AIR TEMPERATURE:

exhaust temperature has reached the value set in the field.

98 –

ENGLISH

Periodic warning interval setting (E-mail is sent on the checked days of the week/times)

ENGLISH

Special Features

– 99

How to use network function (continued)

E-mail setup page (continued)



Enter the E-mail address to which the E-mail is to be sent when two E-mail addresses are going to be used. Do not enter it when the second E-mail address is not going to be used.

Select the conditions for sending E-mail to the second E-mail address.

MAIL CONTENTS:

Select “NORMAL” or “SIMPLE”.

ERROR:

an error is detected by self-diagnosis.

LAMP1 RUNTIME:

remaining lamp service time has reached the value set in the field.

LAMP2 RUNTIME:

remaining lamp service time has reached the value set in the field.

LAMP3 RUNTIME:

remaining lamp service time has reached the value set in the field.

LAMP4 RUNTIME:

remaining lamp service time has reached the value set in the field.

INPUT AIR TEMPERATURE:

intake air temperature has reached the value set in the field.

OUTPUT AIR TEMPERATURE:

exhaust temperature has reached the value set in the field.

100 –

Check these boxes when E-mail is to be sent periodically to the second E-mail address. E-mail will be sent at the times and on the days checked.

Button to update settings

ENGLISH

Panasonic PT-D12000E, PT-DZ12000E Operating Instruction

Specifications and Main Features

Frequently Asked Questions

User Manual

Dear Panasonic Customer:

Contents

IMPORTANT SAFETY NOTICE

IMPORTANT: THE MOULDED PLUG (U.K. only)

Precautions with regard to safety

WARNING

CAUTION

Before Using

Accessories

Caution when moving the projector

Cautions regarding setup

Notes on use

Disposal

Attention on security

Location and function of each part

Remote control unit

Projector Main Unit

Using the remote control unit

Loading batteries

Effective range of remote control operation

Setting projector ID number to remote control

Using a wired remote control

Installation

Examples of system expansion

Adjusting the feet

Projection scheme

Installation geometry

Projection distances by the type of projection lenses (optional)

Installation dimensions diagram

Connection

Before starting connection

Example of connecting with VIDEO devices

Example of connecting with personal computers

Installation of input module (optional)

Installing the input module

Connecting signals to the input module

Connecting the signal to the SD-SDI input module

Connecting the signal to the HD/SD-SDI input module

Connecting the signal to the dual link HD/SD-SDI input module

Connecting signals to the DVI-D input module

How to install and remove the projection lens (optional)

How to install the projection lens

How to remove the projection lens

Projection

Power indicator lamp

Connecting the power cord

Powering up the projector

Making adjustment and selection

Powering off the projector

How to adjust the lens

How to adjust the focus, zoom and shift

Adjustment range after lens position (optical shift)

Moving the projection lens position to the home position

How to adjust the lens mounter for addressing unevenness of focusing

Registration of input signal data

Registration of new data

Renaming the registered signals

Clearing the data of registered signals

Sub memory

Basic operations using the remote control

Switching the input signal

Using the SHUTTER function

On-screen display function

Status function

Using the FUNC1 button

Displaying the internal test pattern

Changing the picture aspect ratio

On-screen menus

MAIN MENU

SUB MENU

Using the menu screens

Resetting to the factory default

Adjusting the picture

Switching the picture mode

Adjusting Contrast

Adjusting Brightness