Panasonic PT 60LCX63, PT-50LCX63 User Manual

Digital Device Display

Operating Instructions

Models No.

(USA)

For assistance, please call :
1-888-VIEW PTV(843-9788)

or, contact us via the web at:
http://www.panasonic.com/contactinfo

(Puerto Rico)

For assistance, please call :
787-750- 4300

or visit us at www.panasonicpr.com

PT-50LCX63/PT-60LCX63

Three Important Reasons to Register Your
Product Immediately!

1 Protect Your New Investment...

Register your new Device Display for insurance purposes

in case your new Device Display is stolen.

2 Product safety notifi cation...

Registering your product can help us to contact you in the

unlikely event a safety notifi cation is required under the
Consumer Product Safety Act.

3 Improved Product Development...

Help us continue to design products that meet your needs.
Register online at www.panasonic.com/register

* The presence of the DT V certifi cation mark indicates that this product will

successfully receive digital television transmissions that conform to any and

ATSC CERTIFIED *

DIGITAL TELEVISION

This operating instruction book is designed for use with models PT-50LCX63 and PT-60LCX63. Illustrations in
this manual show the PT-50LCX63.

Before connecting, operating or adjusting this product, please read the instructions completely.
Please keep this manual for future reference.

all of the video formats described in the ATSC Digital Television Standard.

LSQT0742 A

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: To reduce the risk of electric shock, do not remove cover or back. No
user-serviceable parts inside. Refer servicing to qualified service personnel.

This symbol warns the user
that uninsulated voltage
within the unit may have
suffi cient magnitude to
cause electric shock.
Therefore, it is dangerous
to make any kind of contact
with any inside part of this
unit.

This symbol alerts the
user that important
literature concerning
the operation and
maintenance of this unit
has been included.
Therefore, it should be
read carefully in order to
avoid any problems.

The pictorial
representation of a hot
surface within a triangle
is intended to tell the
user that parts inside
the product are a risk of
burns to persons.

Note to CATV System Installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifi es that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.

WARNING

To reduce the risk of electric shock, fi re, injury to persons or damage to this product:

1) Read all instructions before using, connecting or adjusting this product.

2) Retain these safety and operating instructions for future reference.

3) Adhere to all warnings on the product and in this Operating Instructions manual.

4) Follow all instructions carefully.

5) Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a
wet basement or near a swimming pool, and the like. Do not place objects fi lled with water, such as a vase or
the like, on top of this unit.

6) Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners.

7) Do not block any ventilation openings. Install only in accordance with the manufacturer’s instructions.
Openings in the cabinet are provided for ventilation, to ensure reliable operation and to protect it from
overheating. Never block openings by placing the product on a bed, sofa or similar surfaces.

8) Do not install near a heat source, such as a radiator, heat register, stove, or similar appliances (including
amplifi ers). Do not install in a built-in installation such as a bookcase or rack, unless proper ventilation is
provided or the manufacturer’s instructions have bee adhered to.

9) Insert plug in outlet fully - Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades, one wider than the other. A grounding type plug has two blades and a grounding
prong. The wide blade or grounding prong is provided for your safety. If the provided plug does not fi n into your
outlet, consult a qualifi ed electrician to replace the obsolete outlet.

10) Protect the power cord from being walked or tripped over, pinched or entangled

11) Use only attachments or accessories specifi ed by the manufacturer.

12) Never place unit on support or stand that is not fi rm, level, and adequately strong. The unit
could fall causing serious injury to a child or adult and damage to the unit.

• Move any appliance and cart combination with care. Quick stops, excessive force, and uneven

surfaces may cause objects to overturn.

• Carefully fallow all instructions.

13) Unplug this product during lightning storms or when unused for long periods of time.

14) Do not service this unit yourself. Refer all servicing to qualifi ed personnel. Servicing is required when this
product has been damaged in any way, such as if the power cord is damaged, liquid was spilled or objects
were dropped into this unit, or the unit was exposed to rain or moisture, does not operate normally, or has been
dropped.

15) Because the temperature of the lamp unit is elevated immediately after its use, a direct touch to it may cause
burns. Replace the lamp unit only after it has cooled.

2

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

3

Getting Start ed

IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)

WARNING

AS WITH ANY SMALL OBJECT, SD CARDS CAN BE SWALLOWED BY YOUNG CHILDREN. DO NOT ALLOW
CHILDREN TO HANDLE THE SD CARD.

CAUTION

(1) This Device Display is intended to be used with the following TV stand: model TY-50LC13C for the

PT-50LCX63/PT-60LCX63. Use with other stands may result in the Device Display becoming unstable, possibly
causing injury.

(2) This Device Display should not be exposed to direct sunlight, extreme temperatures or moisture, as this can result

in serious irreparable damage.

(3) This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains

lead in some components.
Disposal of these materials may be regulated in your community due to environmental considerations.
For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance:
<http://www.eiae.org.

The lamp has a maximum life of about 10 000 hours.
If use exceeds this fi gure, the possibility of lamp damage becomes greater.
The lamp should be changed as soon as possible once the lamp warning message appears.
If the lamp is damaged, please contact your nearest dealer.

Due to the characteristics and use conditions of in di vid u al lamps, the lamp may cease to light before the
stated lamp life.
Infl uences of fre quent light ing, continuous light use for over 24 hours, the number of times lit, the length of
time between lightings, etc. may shorten lamp life.
(Because of this, we recommend having a replacement lamp on hand.)

>

Trade mar ks

• VGA and XGA are trademarks of International Business Machines Corporation.

• Macintosh is a registered trademark of Apple Computer, USA.

• VESA and SVGA are trademarks of the Video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.

• Equipped with -TV Noise Reduction for true MTS reproduction. -TV Noise Reduction is required for good stereo
separation and audio fi delity. is a registered trademark, and is licensed by Tec hnology Licensing .

SD Logo is a trademark.

Manufactured under license from BBE Sound, Inc.
Licensed by BBE Sound, Inc. under USP4638258 and 4482866.
BBE and BBE symbol are registered trademarks of BBE Sound, Inc.

HDMI, the HDMI logo and High Defi nition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing LLC.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
U.S. Patents Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; 6,381,747; and 6,516,132.

Dear Panasonic Customer

Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new
Device Display.
To obtain maximum benefi t from your set, please read these Instructions before making any adjustments, and retain
them for future reference.
Retain your purchase receipt also, and record the serial number of your set in the space provided on the rear cover
of these instructions.

Visit our Panasonic Web Site for USA : www.panasonic.com

(USA)

For assistance, please call : 1-888-VIEW PTV(843-9788)

or, contact us via the web at: http://www.panasonic.com/contactinfo

(Puerto Rico)

For assistance, please call : 787-750-4300

or visit us at www.panasonicpr.com

FCC STATEMENT:

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

FCC CAUTION:

To assure continued compliance and prevent undesirable interference, use only the provided shielded RGB cable
with 2 ferrite cores while connecting the Device Display to a computer. Any changes or modifi cations not ex press ly
approved by the party responsible for compliance could void the user’s authority to operate this equipment.

ANY CHANGES OR MODIFICATIONS TO THIS PTV RECEIVER NOT EXPRESSLY APPROVED BY MATSUSHITA
ELECTRIC CORPORATION OF AMERICA COULD CAUSE HARMFUL INTERFERENCE, WHICH WOULD VOID
THE USER’S AUTHORITY TO OPERATE THIS EQUIPMENT.

The ClassⅡ insulation symbol (square within a square) indicates that this product has been evaluated
and tested to comply with ClassⅡ insulation requirements.

Declaration of Conformity

Models Number:
Trade Name: Panasonic
Responsible party: Matsushita Electric Corporation of America.
Address: One Panasonic Way Secaucus New Jersey 07094
Telephone number: 1-888-VIEW PTV(843-9788)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

PT-50LCX63/PT-60LCX63

4

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

5

Getting Start ed

Table of Contents

IMPORTANT SAFETY INSTRUCTIONS......................................................... 2

To
Start !

Use
Now !

Before Using ........................................................................................................ 6

Location of Controls ......................................................................................... 10

Installation.......................................................................................................... 14

Power ON / OFF ................................................................................................. 26

Basic Menu Navigation ..................................................................................... 28

Tuning channels ................................................................................................ 30

Device display operation .................................................................................. 34

ASPECT Controls .............................................................................................. 40

Mute / Freeze / SAP ........................................................................................... 42

Picture in Picture (PIP) Screen......................................................................... 44

Split screen ........................................................................................................ 46

Searching for the desired channel (Channel search) .................................... 48

Getting Start ed Basic Operation Advanced Op er a tion Information

Enjoy
More !

Favorite Channel Feature ................................................................................. 49

Picture Adjustments.......................................................................................... 50

Adjusting screen position and size ................................................................. 52

Audio Adjustments............................................................................................ 54

Lock Feature ...................................................................................................... 56

Closed Caption Feature .................................................................................... 64

Channel Caption Feature.................................................................................. 67

Color Temp Feature........................................................................................... 70

Video NR (Noise Reduction) Feature............................................................... 71

3D Y/C Feature ................................................................................................... 72

Setting when 480p signals are input through COMPONENT VIDEO INPUT

3D I/P Feature..................................................................................................... 74

Automatically changing screen size ............................................................... 75

RGB IN Input Feature ........................................................................................ 76

Sleep Timer Feature .......................................................................................... 77

Information......................................................................................................... 78

Demo Mode Feature .......................................................................................... 79

Signal Meter Feature ......................................................................................... 80

Cable Module Info.............................................................................................. 81

About Screen ..................................................................................................... 82

Photo Viewer (SD Card / PC Card)................................................................... 83

....... 73

Other
Information !

Replacing the lamp unit.................................................................................... 88

Remote Control Quick Reference Guide (Operating peripheral equipment)......

Troubleshooting ................................................................................................ 96

Specifi cations .................................................................................................... 97

Cleaning ............................................................................................................. 98

Customer Services Directory ........................................................................... 98

Limited Warranty ............................................................................................... 99

Index .................................................................................................... Back cover

89

Before Using

Receiver Location

This Device Display is intended to be used with an optional stand or entertainment center. Consult your dealer for
available options.
Locate for comfortable viewing. Avoid placing where sunlight or other bright light (including refl ections) will fall on the
screen.
Use of some types of fl uorescent lighting can reduce Remote Control transmitter range.
Adequate ventilation is essential to prevent internal component failure. Keep away from areas of excessive heat or
moisture.

Optional External Equipment

The Video / Audio connection between components can be made with shielded video and audio cables. For best
performance, video cables should utilize 75 Ω coaxial shielded cables. Cables are available from your dealer or
electronic supply house.
Before you purchase any cables, be sure you know what type of output and input connectors your various
com po nents require. Also determine the length of cable you’ll need.

Safety Precaution

Please take safety precautions to prevent the unit from
falling over.

WARNING

The unit may tip or fall if not situated on a stable
surface, if pushed or during an earthquake. Use a
strong rope or chain (not included) to fasten the
Device Display fi rmly to a strong wall support.

6

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

7

Getting Start ed

Before Using

Accessories

1. Remote Control (EUR7627Z10)

2. Batteries 2 “AA”

3. RGB Cable (2 m) (LSJA0239-1 or LSJA0443)

Viewing position

To optimize your viewing comfort, please follow the viewing guidelines shown in the diagrams below.
If viewing for an extended period of time, sit as far back from the screen as possible.

<Top view>

70º

<Side view>

70º

At least 1.8 m (PT-50LCX63)/2.2 m (PT-60LCX63).

30º

30º

At least 1.8 m (PT-50LCX63)/2.2 m (PT-60LCX63).

Before Using

Remote Control Battery Installation

Requires two AA batteries (supplied).

1. While pressing in on the catch,
open cover in direction of arrow.

2. Install the batteries as shown in
the battery compartment.

(Polarity + or - must match the

markings in the compartment).

Two AA size

3. Press cover in direction of
arrow until it snaps shut.

CAUTION

Incorrect battery installation can cause the batteries to leak, leading to personal injury and/or damage to the remote
control.

Observe the following precautions:

1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.

2. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

3. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

4. Battery replacement is necessary when the remote control acts sporadically or stops operating the Device
Display set.

Helpful Hints:

(1) For frequent remote control users, replace old batteries with Alkaline batteries for longer battery life.
(2) Whenever you remove the batteries, you may need to reset the remote control infrared codes. We

rec om mend that you record the code on page 90, prior to setting up the remote.

Emergency Alert System ( EAS) Forced Tuning

If a DCM (Digital Cable Module) is installed, the cable MSO (multiple system owner/operator) may provide
an Emergency Alert System message. These messages are intended to alert the general public of important
local or national emergency situations. In the event of receipt of one of these messages, the Device Display
shall immediately tune to the channel as directed by the EAS message. If the channel has been blocked
using the parental control, the parental blocking has priority over the forced tune.

8

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

9

Getting Start ed

Before Using

Glossary and Acronyms

CC (Closed Captioning)

EAS (Emergency Alert System)

OSD (On-Screen Display)

MSO (Multiple system owner/operator)

Dolby Digital

This is a method of coding digital signals developed by
Dolby Laboratories. Apart from stereo (2-channel) audio,
these signals can also be multichannel audio. A large
amount of audio information can be recorded on one
disc using this method.

Film and video

DVD-Videos are recorded using either fi lm or video.
Usually, fi lm is recorded at 24 frames per second, the
rate movies are fi lmed at, while video is recorded at 30
frames per second.

PCM (pulse code modulation)

These are uncompressed digital signals, similar to those
found on CDs.

DTV (Digital Television)

Name of the process whereby television picture and
sound signals are changed to digital code for receiving
and transmitting.

HDTV (High Defi nition Television)

Television with improved picture quality by increasing
vertical and horizontal resolution.

ATSC (Advanced Television Systems Committee)

Standardization body that developed the Digital
Television Te r restr i a l f ormats .

DCF (Design rule for Camera File system)

Unifi ed standard established by Japan Electronics and
Information Technology Industries Association (JEITA).

HDMI (High Defi nition Multimedia Interface)

Interface that supports every uncompressed digital format
as well as all existing multi-channel audio format on a
single cable.

JPEG (Joint Photographic Experts Group)

A system used for compressing/decoding color still
pictures.

MPAA (Motion Picture Association of America)

Guild governing rating assignments to movies.

NTSC (National Television Systems Committee)

Standardization body that developed the Analog
Television Te r restr i a l f ormats .

Password

A four (4) digit code a user must provide in order to
perform a function.

DCM (Digital Cable Module)

A module that is required to receive premium digital
services through the cable input.

POWER

SAP

LIGHT

MENU

123

456

7809

EXIT

CH

CH

VOL VOL

R-TUNE

PIP MIN

REW

FREEZE

TV/VCR

PIP SPLIT MOVE SWAP

PIP CH

DVD/VCR CH

SEARCH

OPEN/CLOSE

PLAY

PAUSE STOP REC

PIP MAX

FF

PROG

TV/VIDEO

A - ANTENNA - B

TV VCR DVD

DBS RCVR CBL AUX

OK

M

U

T

E

A

S

P

E

C

T

B

B

E

R

E

C

A

L

L

Location of Controls

Illuminated Remote Control

1

2

3
4

5

6

7

8

9

10

18

19

20

21

22

23

24

11

12

13
14

15

16

17

Note:

This section describes TV mode only. For other modes, see pages 89-95.

10

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

25

26

27

28

29

30

31

32

11

Getting Start ed

Location of Controls

Remote Keys DESCRIPTION

1

POWER Press to turn ON and OFF.
TV Sets the remote to communicate with television.
VCR, DVD, AUX,

2

CBL, RCVR,
DBS

3

TV/VIDEO Changes Input source.

4

SD Accesses the Photo Viewer feature (SD Card or PC Card).

5

ASPECT Changes display aspect ratio.

6

MUTE Press to mute sound.

7

VOL ◄► Press to adjust TV sound and navigate in menus.

8

OK Press to choose menu and sub-menu entry.

9

MENU Press to display Main Menu or return one step backward in menus.

10

Number Press numeric keypad to select any channel or press to enter alphanumeric input in menus.

11

R-TUNE Press to switch to previously viewed channel, Photo Viewer or input modes.
PIP MIN While remote is in TV mode, press to decrease the PIP size.

12

REW While remote is in VCR or DVD mode, press to rewind.

13

PLAY While remote is in VCR or DVD mode, press to play.

14

PAUSE While remote is in VCR or DVD mode, press to pause.
FREEZE Still full video window.

15

TV/VCR Press to switch to TV or VCR.

16

PIP Press to display or delete PIP screen.

17

SPLIT Press to display or delete Split screen.

18

SAP

19

LIGHT Lights all buttons. The selected mode button (TV, VCR, etc.) fl ashes.

20

ANTENNA A/B Press to switch to (A or B) RF antenna input.

21

BBE Press to turn BBE OFF or ON.

22

RECALL Press to display or delete Channel banner.

23

EXIT Press to exit menus.

24

CH ▲▼ Press to change channels and navigate in menus.

25

PROG Press after entering major channel numbers to enter minor (-) channel numbers.
PIP MAX While remote is in TV mode, press to increase the PIP size.

26

FF While remote is in VCR or DVD mode, press to fast forward.

27

REC While remote is in VCR mode, press to record.

28

STOP While remote is in VCR or DVD mode, press to stop.

SEARCH

29

OPEN/CLOSE While remote is in DVD mode, press to open or close DVD tray.
PIP CH ▲▼ While remote is in TV mode, press to change channels for PIP.

30

DVD/VCR CH While remote is in VCR or DVD mode, press to change channels for DVD or VCR.

31

SWAP Press to swap Main screen with PIP or Split screen.

32

MOVE While PIP screen is displayed, press to move to one of four corners.

Sets the remote to communicate with other devices.

In analog mode, press to access audio modes (Stereo, SAP or Mono). In digital mode, press
to access next audio track.

While remote is in TV mode, press to scan available channels in search screens. Press again
to delete search screens.

Location of Controls

Controls and Terminals on the Device Display

Model PT-50LCX63 unit shown

< FRONT >

POWER button/
POWER indicator
(P. 26)

Volume up(+) / down(–)
buttons
(P. 34)

Channel up / down buttons
(P. 34)

A

LAMP indicator
This indicator lights up when there is
a malfunction with the lamp unit.
(PP. 88, 96)

TEMP indicator
This indicator lights up when there
is an abnormal tem per a ture in the
unit.
(P. 96)

Remote Control Sensor

A

Using your fi nger,
slide Slot Cover in
direction of arrow to
open.

SD CARD slot

Open

Slot Cover

PC CARD slot

12

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

13

Getting Start ed

Location of Controls

Model PT-50LCX63 unit shown

< REAR >

Vent

DCM INTERFACE
(POD INTERFACE)
(p. 16)

DIGITAL AUDIO
OUT terminal
(P. 21)

Vent

SERVICE ONLY
Card slot used by a certifi ed service
technician only. Do not insert any
memory card into this slot.

Antenna A, B terminal
(PP. 14-16)

< SIDE >

RGB Input 2 terminal
(P. 22)

RGB Input 1
terminal
(P. 22)

Input 1, 2 ter mi nals
(P. 17)

AV OUT terminals
(PP. 19-20)

Notes:

• Make sure the vents are not blocked. (This could cause damage.)

• Indication on the back panel may change without notice.

Component signal input 1-3 ter mi nals
(P. 18)

HDMI input
terminal
(PP. 24-25)

Input 3 ter mi nals
(P. 17)

Installation

Notes on con nec tions

• Turn off the power supply for all com po nents before making any connections.

• If the cables necessary for connecting a component to the system are not included with the component or available as an
option, you may need to fashion a cable to suit the component concerned.

• Read the instruction manual for each system component care ful ly before connecting it.

• If there is a lot of jitter in the video signal input from the video source, the picture on the screen may fl icker. In this case, it will
be necessary to connect a TBC (time base corrector).

CAUTION

When using “Nut type” RF coaxial cables, tighten with fi ngers only. Overtightening may damage terminals.

Connecting the Antenna / Cable to the RF IN Terminal

For proper reception of analog or digital cable channels, a cable service connection is required.

Cable Connection

Connect the cable supplied by your local cable company to ANTENNA (A) connection on back of unit. Select Cable
mode and ANTENNA (A) in SET UP menu under Program Channel.

14

CABLE BOX

TERMINAL ON THE
BACK OF THE
CABLE BOX

In from cable

In from cable

Note:

Cable Mode is preset at the factory. Antenna users must change to ANTENNA Mode for ANTENNA (A) in the Setup menu. If you
have both Cable and Antenna, the Cable must be connected to ANT A.

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

Or

Connect the cable from the
antenna or cable system to the
ANTENNA (A) terminal on
the back of the Device Display.

15

Getting Start ed

Installation

Antenna Connection

For proper reception of digital and analog VHF/UHF channels, an external antenna is required. For best reception,
an outdoor antenna is recommended.
Connect home antenna to either ANT (A) or ANT (B) connection on back of the unit. Select Antenna mode for
Cable/Antenna, Cable only, Antenna only or in Input Setup under Program Channel in Setup menu.

Antenna connect only:

Mixer

ANTENNA (A)
TERMINAL ON THE
BACK OF THE DEVICE
DISPLAY

Antenna and Cable connect:

VHF Antenna

In from cable

UHF Antenna

Mixer

ANTENNA (B)
TERMINAL ON THE
BACK OF THE DEVICE
DISPLAY

Note:

When connecting an antenna only, connect to
Antenna (A). When connecting both an antenna
and a cable, connect the antenna to Antenna (B).

Installation

Digital Cable Module Connection

This module allows you to tune digital and high defi nition cable channels through the cable antenna.
Consult your Cable company on the availability of this module (also called Point of Deployment (POD)
module).

Connect the Cable antenna to ANT A/Cable In input on the back of the unit.

1

Insert the DCM (Digital Cable Module) (upper side facing left) into the DCM INTERFACE (POD INTERFACE)

2

slot on the back of the unit.

16

DCM (Digital Cable Module)

Notes:

• A Digital Cable Subscription is required. (See page 81)

• Do not insert a PC card into the DCM INTERFACE (POD INTERFACE).

• Choose Cable mode for Antenna (A) in Input Setup.

• Follow the instructions on screen.

If you experience keyboard or remote control function hang-up when using DCM (Digital Cable Module), unplug the
unit and plug it back on and try the controls again. If this condition still exists, please call Panasonic Customer Call
Center for further instructions.

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

In from cable

17

Getting Start ed

Installation

How to connect the “1, 2, 3” Input Terminals

Connects VCRs and other peripheral equipment

(S-VHS VCR)

S-VIDEO

AUDIO

Similar connections are available at the INPUT 1, 2, 3 input terminals.
(P. 13)

(VHS VCR)

VIDEO

AUDIO

Similar connections are available at the INPUT 1, 2, 3 input terminals.

Notes:

• Input 3 is located on the side of the unit.

• Select the desired VIDEO input position by pressing the TV/VIDEO button. (P. 37)

• When connecting video cables, priority is given to the S-Video cable when the S-Video input terminal and the video input
terminal are connected at the same time.

Installation

How to con nect the COMPONENT VIDEO Input Terminals

Because each Y, PB, and PR signal is input independently, the Component signal allows for more accurate
color reproduction.
The Component signal output terminal indication will differ according to the output device ( Y, PB, PR).
Please read the operating instructions included with the output device.

DVD Player

COMPONENT VIDEO

AUDIO

Notes:

• Similar connections are available at the COMPONENT VIDEO INPUT 1-3 Terminals.

• Select the desired COMPONENT VIDEO INPUT position by pressing the TV/VIDEO button. (P. 37)

• Component video signals that can be input are 480i, 480p, 720p, and 1080i.

Component Signals (Y, PB, PR) that can be Input

Signal data

Mode type

480i 664 X 485 15.73 29.97 480 i

480p 720 X 483 31.47 59.94 480 p

No. of dots

(H X V)

Horizontal frequency

(kHz)

Vertical frequency

(Hz)

Information menu

display

18

720p 1 280 X 720 45.00 60.00 720 p

Signals

DTV Format

*1080i 1 920 X 1 080 33.75 30.00 1080 i

Note:

Input signals, other than those listed with a * mark, will give you a beautiful, stable picture.

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

19

Getting Start ed

Installation

How to connect the AV OUT Terminals

You can connect a VCR to the AV OUT terminal to record the program you are viewing on-screen. An
external monitor can also be connected to the AV OUT terminals. Connect the VCR as shown below.

Recording Equipment
(S-VHS /VHS VCR)

S-VIDEO

Or

VIDEO

AUDIO

Notes:

• This unit contains Video and Audio Outputs for the purpose of recording television programming to VCR. Due to license restrictions,
if a device (STB, DVD, etc.) is connected to the HDMI input of the unit, no video or audio output is allowed.

• AV Out signal is available when receiving digital channel. However, all formats will be down converted to NTSC.

• Never connect the VIDEO IN and OUT terminals to the same video recorder, as this could cause incorrect operation.

• Even if unit is in Split or PIP mode, OUT terminals only output the main picture and sound signals. A sub-picture, including
channel search, etc., will not be output.

• AV terminals will not output Y, PB, PR, RGB/HDMI IN or SD/PC card signals.

• The S-Video OUT terminal outputs the same signal that is input from the S-Video IN terminal and Digital RF channels.

• Certain program content output from the AV Out connector may have the Macrovision signal modifi cation applied to its signal,
preventing VCRs from recording this video signal.

Installation

How to connect the Amplifi er

Analog Audio Out

To listen to the audio through a separate stereo system, connect an external audio amplifi er to AUDIO OUT
on back of unit.

Stereo System
(A Stereo Amplifi er and Speakers)

AUDIO

Note:

AUDIO OUT terminals cannot be connected directly to external speakers.

Audio Adjustments

• Select Speakers Off in Audio menu under Other Adjust menu.

• Set amplifi er volume to the preferred level.

20

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

21

Getting Start ed

OPTICAL

Installation

Digital Audio Out

Use the diagram below to connect the Digital Audio Output of your Device Display to a Dolby Digital
decoder.

Dolby Digital 5.1 channel surround sound delivers digital-quality sound. Dolby Digital provides fi ve discrete
full-bandwidth channels for front left, front right, center, surround left and surround right, plus a LFE (Low Frequency
Effect) subwoofer channel, For a full Home Theater sound experience, an external Dolby Digital decoder and a
multichannel amplifi er must be connected to the Digital Audio Out jack on the unit.

Procedure

Connect the Digital Audio cable from the Digital Audio
Out jack on the unit to the Digital Audio In connection on
the Dolby Digital decoder.

Note:

When ATSC channel is selected, the output from the Digital
Audio Out jack will be Dolby Digital. But, if NTSC channel is
selected, the output will be PCM.

Manufactured under license
from Dolby Laboratories. “Dolby”
and the double-D symbol are
trade marks of Dolby
Laboratories.

Firmly connect
the cable to
the connector.

Amplifi er with built in
Dolby Digital decoders.

Speakers (example)

Connect three
or more
speakers for
surround
sound.

RGB OUT AUDIO OUT

Installation

How to connect the RGB IN Terminals

Connecting a PC to RGB IN

COMPUTER

Connect a cable which matches the audio
output terminal on the computer.

PC audio cable
(M3 stereo mini pin)

RGB IN Terminal (D-SUB 15P) Pin Layouts

67839

1

2

Connection port view

Notes:

• Some PC models cannot be connected to the set. A conversion adapter is required to use the RGB cable (D-SUB 15P) to
connect a Macintosh computer to the set. There is no need to use an adapter for computers with PC / AT compatible D-SUB
15P terminal.

• The computer shown in the illustration is for example purposes only. Additional equipment and cables shown are not supplied
with this set.

• The picture will become dark if an PC signal with a vertical scanning frequency of 62 Hz is input. To obtain the optimum picture
quality with the Device Display, a vertical scanning frequency of 60 Hz is recommended.

• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specifi ed frequency
range.

• Select the desired RGB input position by pressing the

• Similar connections are available at the RGB IN 1, 2 Terminals.

Conversion adapter
(If necessary)

1514131211

10

45

RGB cable (D-SUB 15P)

Pin No. Signal name

1R
2G
3B
4NC
5NC
6 Ground for R
7 Ground for G
8 Ground for B

NC: Not connected

TV/VIDEO button. (P. 37)

Pin No. Signal name

9NC
10 Ground
11 N C
12 NC
13 HD/CSYNC
14 VD
15 NC

22

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

23

Getting Start ed

Installation

RGB signals that can be input

The table below lists the different types of RGB signals that can be input.
If a signal which differs greatly from any of the types listed below is input, the picture image may not be
dis played correctly, or a black background may be displayed. At this time, “signal” will fl ash in the
on-screen display for about 5 seconds.

Signal data

Mode type

VGA400 (70 Hz) 640 X 400 31.47 70.08 VGA400 70Hz

VGA480 (60 Hz) 640 X 480 31.47 59.94 VGA 60Hz

Macintosh 13″ 640 X 480 35.00 66.67 MAC 13

VESA400 (85 Hz) 640 X 400 37.86 85.08 VESA 85Hz

VESA480 (72 Hz) 640 X 480 37.86 72.81 VGA 72Hz

VESA480 (75 Hz) 640 X 480 37.50 75.00 VGA 75Hz

VESA480 (85 Hz) 640 X 480 43.27 85.01 VGA 85Hz

SVGA (56 Hz) 800 X 600 35.16 56.25 SVGA 56Hz

SVGA (60 Hz) 800 X 600 37.88 60.32 SVGA 60Hz

No. of dots

(H X V)

Horizontal frequency

(kHz)

Vertical frequency

(Hz)

Information menu

display

SVGA (72 Hz) 800 X 600 48.08 72.19 SVGA 72Hz

SVGA (75 Hz) 800 X 600 46.88 75.00 SVGA 75Hz

SVGA (85 Hz) 800 X 600 53.67 85.06 SVGA 85Hz

Personal Computer Signals

Macintosh 16″ 832 X 624 49.73 74.55 MAC 16

* XGA (60 Hz) 1 024 X 768 48.36 60.00 XGA 60Hz

* XGA (70 Hz) 1 024 X 768 56.48 70.07 XGA 70Hz

* XGA (75 Hz) 1 024 X 768 60.02 75.03 XGA 75Hz

* Macintosh 19″ 1 024 X 768 60.24 74.93 MAC 19

480i 664 X 485 15.73 29.97 480 i

480p 720 X 483 31.47 59.94 480 p

720p 1 280 X 720 45.00 60.00 720 p

Signals

DTV Format

* 1080i 1 920 X 1 080 33.75 30.00 1080 i

Notes:

• Input signals, other than those listed with a * mark, will give you a beautiful, stable picture.

• The D-SUB15P connector can accept RGB (H-V sync separate) and RGB (sync on green). However, it is not guaranteed to
display stable color when using RGB (sync on green).

• When used with an external video processor/scaler, it must have RGB (H-V sync separate) output.

Installation

HDMI OUT

How to connect the HDMI input terminal

About HDMI

HDMI is the fi rst all digital consumer electronics A/V interface that supports several uncompressed standard,
enhanced and high defi nition video format as well as all existing multi-channel audio formats. One jack supports both
video and audio information. The HDMI/HDCP1 input can be connected to an EIA/CEA 861/861B2 compliant
consumer electronic device, such as a set top box or DVD player equipped with a HDMI output connection. By
inputting a High-bandwidth Digital Content Protection (HDCP) high defi nition picture source to the HDMI terminal of
this unit, high defi nition pictures can be displayed on the screen in their digital form. The HDMI input terminal is not
intended to be used with personal computers. This unit is compatible with 1080i, 720p and 480p formats. Select the
output of the connected device to match that of the unit.

Connection diagram

Follow the diagram below to connect the unit to a set top box or a DVD player.

When audio signal input is digital.

Set top box

The connector on the unit is HDMI Type A connector.

When audio signal input is analog.

Set top box

HDMI OUT

Notes:

1

HDMI/HDCP = High Defi nition Multimedia Interface / High-Bandwidth Digital Copy Protection.

2

EIA/CEA-861/861B Profi les compliance covers profi les for transmission of uncompressed digital video including high bandwidth

digital content protection.

AUDIO OUT

The connector on the unit is HDMI Type A connector.

24

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

25

Getting Start ed

Installation

Procedure

Connect the HDMI output from the set top box or a DVD player to the HDMI input on the back of the unit.

1

• If you cannot display the picture because your Digital Set Top Box does not have a Digital Out terminal
setting, use the Component Video Input (or the S-Video Input or Video Input). In this case, the picture will be
displayed as an analog signal.

Press TV/VIDEO on the Remote Control to select HDMI input.

2

By inputting a High-bandwidth Digital Content Protection high-defi nition picture source to the HDMI IN terminal of
this Device Display, high-defi nition pictures can be displayed on the screen in their digital form. (This terminal is for
use in the future when High-bandwidth Digital Content Protection DVD players and D-VHS are put on the market.)

Notes:

• Select the HDMI input position by pressing the TV/VIDEO button. (P. 37)

• The

HDMI IN terminal can only be used with 1080i, 720p and 480p picture signals.

• If there is no audio, check if the source equipment has PCM output. If not, please use analog connections.

• Be sure HDMI is securely connected. If not, picture noise and/or incorrect picture display may result.

• With HDMI connection, depending on the signal, the picture may be displayed with unnatural colors (as if red and blue are
reversed). See UV Timing of Page 53.

Compatible formats

Video Signal:
The Device display is compatible with following formats. Please set the connecting device to following format.

Display mode No. of dots Vertical scanning frequency (Hz)

1080i 1920 x 1080i 59.94 / 60

720p 1280 x 720p 59.94 / 60

480p 720 x 480p

640 x 480p

59.94 / 60

59.94 / 60

Audio signal ( PCM)

When digital audio is included in the HDMI connection, the compatible sampling frequencies are 48 kHz/44.1 kHz/32
kHz. (See page 55)

POWER

SAP

LIGHT

TV/VIDEO

A - ANTENNA - B

TV VCR DVD

DBS RCVR CBL AUX

Power ON / OFF

Turning the Power ON and OFF

Always be sure to follow the procedure given below to turn the Device Display power ON and OFF.

• The lamp cooling fan will continue to operate for approximately 1 minute after the power is turned off. At the same time, the
POWER indicator will blink Red.

Do not disconnect the power cord from the outlet and do not open the circuit breaker (unless necessary)
while the cooling fan is still operating. Do not disconnect the power cord from the power outlet while the
power indicator blinks Red.

POWER button/
POWER indicator

Power ON

Press POWER on Device Display or Remote Control to
turn power on.

The Power Indicator blinks Green for about 10 seconds
and then turns solid Green.

Power OFF

Press POWER on Device Display or Remote Control to
turn power off.

Power shuts off after a Black Screen is displayed for a
few seconds.

Note:

If the POWER button is pressed during the Black Screen
display, Power is turned back on.

The Power Indicator blinks Red for about 1 minute and
then turns solid Red.

Note:

When the AC Cord is unplugged, the internal cooling fan stops op er at ing. In this case, the lamp will be insuffi ciently cooled and will
take a while to turn ON again.

26

Notes:

• If the POWER button is accidentally turned off during use, after power is turned back on, it may take a short period before the
lamp automatically comes on.

• After the unit is turned on, maximum picture brightness will be achieved in 5-10 minutes. This is normal.

• This unit consumes approx. 20 W in OFF condition when plugged into an AC outlet.

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

The Power Indicator

LED ACTION

Red Power – OFF (Standby mode)
Red blink Power – OFF (Now cooling)
Green Power – ON
Green blink Power – ON (Preparing to light lamp)

27

Basic Operation

Power ON / OFF

POWER

SAP

LIGHT

MENU

123

456

7809

EXIT

CH

CH

VOL VOL

R-TUNE

PIP MIN

REW

FREEZE

TV/VCR

PIP SPLIT MOVE SWAP

PIP CH

DVD/VCR CH

SEARCH

OPEN/CLOSE

PLAY

PAUS E ST OP REC

PIP MAX

FF

PROG

TV/VIDEO

A - ANTENNA - B

TV VCR DVD

DBS RCVR CBL AUX

OK

M

U

T

E

A

S

P

E

C

T

B

B

E

R

E

C

A

L

L

First Time Setup

For your convenience, First Time Set up menu will be displayed on screen when the set is turned on for the
fi rst time. If needed, follow the menus and procedures displayed on-screen for setting up the features.

Input Setup

To select the confi guration of RF input depending on the signal source.

Note:

No video will be displayed in this setup mode.

First time setup

Input Setup Setting Cable/Antenna

Auto Scan

Procedure

Press VOL ► to select Cable only, Cable/Antenna, or Antenna only.

Press OK to underline your selection.

When the next screen is displayed, press OK to start the Auto Scan. All
available channels with a signal will be programmed into memory.

SELECT OK
CHANGE

MENU

to return

EXIT

Notes:

• Auto scan must be done when you select the input signal for the fi rst time or whenever you change the antenna confi guration.

• Depending on conditions, Auto scan may take a while.

Auto Scan

This feature allows you to selectively auto scan channels. You can Scan
All, Analog only channels, or Analog & Digital channels.

First time setup

Input Setup

Auto Scan

Scan All
Antenna (A) Analog
Antenna (A) Analog & Digital

Antenna (B) Analog
Antenna (B) Analog & Digital

SELECT OK

MENU

to return

EXIT

Procedure

Press OK to start Auto Scan.

After Auto Scan is completed the unit tunes to the fi rst channel found
during auto scan.

Notes:

• If DCM (Digital Cable Module) is present during the First Time Setup and Antenna (A)
is set to cable, Antenna (A) will not be scanned due to the DCM providing the channel
map.

• If setup is incomplete, check connection of Antenna/Cable to the RF IN Terminal, then
try Auto Scan again. (PP. 30-31)

Basic Menu Navigation

CH

CH

VOL VOL

OK

Picture

PicMode STANDARD

Color +32
Tint +32
Brightness +32
Picture +32
Sharpness +32
Normal Set
Other Adjust

SELECT OK

RETURN EXIT

Picture

PicMode STANDARD

Color +32

Tint +32
Brightness +32
Picture +32
Sharpness +32
Normal Set
Other Adjust

SELECT
CHANGE
RETURN EXIT

MENU

POWER

SAP

LIGHT

MENU

123

456

7809

EXIT

CH

CH

VOL VOL

R-TUNE

PIP MIN

REW

FREEZE

TV/VCR

PIP SPLIT MOVE SWAP

PIP CH

DVD/VCR CH

SEARCH

OPEN/CLOSE

PLAY

PAUS E STO P R EC

PIP MAX

FF

PROG

TV/VIDEO

A - ANTENNA - B

TV VCR DVD

DBS RCVR CBL AUX

OK

M

U

T

E

A

S

P

E

C

T

B

B

E

R

E

C

A

L

L

Pressing MENU

1

displays the Main
Menu screen.

Pressing
MENU again
displays
previous level
menu.

Note:

Depending on the signal
being input, some items
may or may not be
adjustable and some
functions may or may not
be available.

2

Press to select the desired

CH

VOL VOL

OK

CH

Press to enter the menu.

icon.

28

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

Press to select desired menu item.

CH

VOL VOL

OK

CH

Continued in left column of next page.

29

Basic Operation

Basic Menu Navigation

CH

CH

VOL VOL

OK

EXIT

Other Adjust

Color Temp Normal

Video NR Off

3D Y/C On
Color Matrix SD
3D I/P Off
ID1 On

SELECT OK

RETURN EXIT

Other Adjust

Color Temp Normal

Video NR On

3D Y/C On
Color Matrix SD
3D I/P Off
ID1 On

SELECT OK

RETURN EXIT

Continued from page 28.

Press to adjust or set desired

CH

VOL VOL

OK

CH

Color +32

menu item.

Note: For Other Adjust sub-menu.

Press to select Other Adjust.

Continued from left column.

Press to select desired sub-menu

Press to select desired sub-menu

CH

VOL VOL

OK

CH

CH

VOL VOL

OK

CH

items.

items.

Picture

PicMode STANDARD
Color +32
Tint +32
Brightness +32
Picture +32
Sharpness +32
Normal Set

Other Adjust

Press to access Other Adjust

CH

VOL VOL

OK

CH

Other Adjust

Color Temp Normal

Video NR Off
3D Y/C On
Color Matrix SD
3D I/P Off
ID1 On

sub-menu.

SELECT OK

RETURN EXIT

SELECT OK

RETURN EXIT

Note: To EXIT menus.

Press repeatedly until normal

Press

MENU

picture is displayed.

to return to normal picture.

Continued in right column.

Tuning channels

CH

CH

VOL VOL

OK

Program Channel

Input Setup Setting Cable/Antenna

Auto Scan

Manual Program

Signal Meter

Connect Cable to Antenna (A)

Connect Antenna to Antenna (B)

Change your Input Setup

and press OK

SELECT OK
CHANGE

EXIT

MENU

to return

Program Channel

Input Setup Setting Cable only

Auto Scan

Manual Program

Signal Meter

Auto scan is needed

press OK to start Auto scan

SELECT OK
CHANGE

EXIT

MENU

to return

POWER

SAP

LIGHT

MENU

123

456

7809

EXIT

CH

CH

VOL VOL

R-TUNE

PIP MIN

REW

FREEZE

TV/VCR

PIP SPLIT MOVE SWAP

PIP CH

DVD/VCR CH

SEARCH

OPEN/CLOSE

PLAY

PAU SE S TO P REC

PIP MAX

FF

PROG

TV/VIDEO

A - ANTENNA - B

TV VCR DVD

DBS RCVR CBL AUX

OK

M

U

T

E

A

S

P

E

C

T

B

B

E

R

E

C

A

L

L

Automatic channel setting

Automatically searches and adds receivable channels to memory.

Press MENU to display the Main Menu screen.

1

2

3

CH

VOL VOL

OK

CH

CH

VOL VOL

OK

CH

Press to select
Setup icon.

Press to display
the options in the
Setup menu.

Press to select
Program CH
icon.

Press to display
the Program
Channel menu.

Press to select
Input Setup.

Press to enter
the sub-menu.

30

For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

4

CH

VOL VOL

OK

CH

Press to select Cable Only, Cable/Antenna
or Antenna Only.

Note:

TV or Cable Tuning mode must be set according
to your connections.

Press to set.

Continued on the next page.