Panasonic MINAS-BL KV, MBEK5A1BCV, MBEK021BCV, MBEK5A5BCV, MBEK015BCV Technical Instructions
...
Technical Instructions (Basic)
●This product is for industrial equipment. Don't use this product at general household.
MINAS-BL KV series
Brushless Amplifier
• Thank you very much for your purchase of Panasonic product.
• Please read this instruction manual carefully for proper use.
• In particular, be sure to read Safety precautions (P.2 to 4) before use for safety.
• Keep this manual with care after reading, and read as necessary.
Be sure to give this Instruction manual to an end user.
* This product image is 200 W type
of KV-series.
• Label of safety precaution is afxed to the product.
If you are the rst user of this product, please be sure to read the instruction
Manual (Overall) from our Web Site.
[Web address of Panasonic Corporation]
http://industrial.panasonic.com/ww/i_e/25000/motor_fa_e/motor_fa_e.html
Safety Precautions
Important
The following explanations are for things that must be observed in order to
prevent harm to people and damage to property.
• Misuses that could result in harm or damage are shown as follows, classified
according to the degree of potential harm or damage.
Indicates great possibility of death or serious
Danger
injury.
Indicates the possibility of injury or property
Caution
• The following indications show things that must be observed.
damage.
Indicates something that must not be done.
Indicates something that must be done.
DANGER
Do not touch the rotating part of the motor
while operating.
The failure could result in injuries.
Do not touch the motor, amplier, and external
regenerative resistor, since they become hot.
The failure could result in burns.
Ground the earth of the brushless motor and
brushless amplier.
The failure could result
in electric shocks.
Install an external emergency stop device
to shut down the main power source in any
emergency.
The failure could result in electric shocks,
injuries, re, damages or malfunction.
Make sure to secure the safety after the
earthquake.
The failure could result
in electric shocks, injuries, or re.
Mount the brushless motor, brushless
amplier and external regenerative resistor on
incombustible material such as metal.
The failure could result
in electric shocks, injuries, or re.
Arrange the phase sequense of the motor and
wiring of the CS sensor.
The failure could result
in injuries, damages, or malfunction.
An over-current protection, earth leakage
breaker, over temperature protecter and
emergency stop device must be installed.
The failure could result
in electric shocks, injuries, or re.
Install the product properly to avoid personal
accidents or re in case of an earthquake.
The failure could result
in electric shocks, injuries, or re.
Only persons who are trained and qualied
to work with or on electrical equipment are
permitted to operate or maintain this equipment.
The failure could result
in electric shocks.
Transportation, wiring and checking must
be performed with power source turned off
and after making sure that there is no risk of
electric shock.
The failure could result
in electric shocks or injuries.
Do not expose the cables to sharp objects,
excessive pressing or pinching forces, and
heavy loads.
The failure could result in electric
shocks, damages, or malfunction.
Do not climb or stand on the brushless
equipment.
The failure could result in electric shocks,
injuries, damages, or malfunction.
Do not place inammable matter near the motor,
amplier and external regenerative resistor.
The failure could result in re.
Do not subject the product to water, corrosive
or ammable gases, and combustibles.
The failure could result in re.
Do not put your hands in the brushless
amplier.
The failure could result in burns,
or electric shocks.
Do not connect the cable (U, V and W) of the
brushless motor directly to the commercial
power source.
The failure could result
in re, malfunction or damage.
CAUTION
Do not approach to the equipment after
recovery from the power failure because they
may restart suddenly.
The failure could result in injuries.
Do not hold the cables or motor shaft when
transporting the motor.
The failure could result in injuries.
Do not drive the motor from the external power.
The failure could result in re.
Never start and stop the motor by magnet
contactor which is provide on the main line.
The failure could result in damages.
－3－－2－
Safety Precautions
Model No.
Voltage
INPUT OUTPUT
Phase
F.L.C
Freq.
Power
200-240 V
3ø
4.0 A
50/60 Hz
0-240 V
3ø
3.6 A
0-267 Hz
750 W
Ser.No.
P13030001
BRUSHLESS AMPLIFIER
MBEK083BCV
Made in China 20130301
合格
Serial Number
MBEK 5A 1 B C V
Important
Introduction/ Checking the model
Do not frequently turn on and off the master
power source.
The failure could result in malfunction.
Do not subject the brushless amplier, motor
or shaft to high impact.
The failure could result in malfunction.
Do not modify, dismantle or repair the product.
The failure could result
in electric shocks, injuries, or re.
If trip occurs, remove the causes of the trip and
secure the safety before restarting.
The failure could result in injuries.
Execute the trial-operations with the motor xed
and a load unconnected. Connect a load to the
motor after the successful trial-operations.
The failure could result in injuries.
Use the specied voltage on the product.
The failure could result
in electric shocks, injuries, or re.
Install a safety device against idling or locking
of gear head, and leakage of grease.
The failure could result in injuries,
damages, and contaminations.
CAUTION
Do not place any obstacle that blocks ventilation
around the brushless amplier and the motor.
The failure could result in burns or re.
Do not block the heat dissipation hole.
The failure could result
in electric shocks, or re.
Be sure to turn off power when not using it for
a prolonged time.
The failure could result in injuries due
to unintentional operation.
Maintenance and check must be performed by
an expert.
The failure could result
in injuries and electric shock.
Conduct proper installation according to
product weight or rated output.
The failure could result
in injuries, or damages.
Use the motor and amplier with the specied
combination.
The failure could result in re.
Ambient temperature of installed motor and
amplier should be under permittable one.
The failure could result in damages.
This product should be treated as an industrial
waste when it is disposed.
After unpacking
• Make sure that the model is what you have ordered.
• Check whether the product has been damaged or not during transportation.
If any deciency should be found,
contact the dealer store where you bought this product.
Checking the model of Amplier and Motor
This amplier is designed for use in combination with a motor to be specied by us.
Check a name of series, rated output, voltage specications you wish to use
You must not use any other combinations than those listed below:
Standard
Voltage Out put Amplier Type Applicable Motor
Single phase AC100 to 120 V
Single phase/3-phase AC200 to 240 V
3-phase AC200 to 240 V
* Sufx of “□” in the motor model
represents shape of shaft.
50 W MBEK5A1BCV MBMS5AZBL
100 W MBEK011BCV MBMS011BL
200 W MBEK021BCV MBMS021BL
50 W MBEK5A5BCV MBMS5AZBL
100 W MBEK015BCV MBMS012BL
200 W MBEK025BCV MBMS022BL
400 W MBEK045BCV MBMS042BL
750 W MBEK083BCV MBMS082BL
Shaft
Oil seal
without A S N
with C U Q
Round Keyway, center tap D-cut
□
□
□
□
□
□
□
□
Checking the model of brushless amplier
Nameplate
Model name
input/output voltage
input/output phase
Rated
input/output current
input/output
Frequency
Rated output
Check the Model Name
KV Series motor drive
Output
5A: 50 W
01: 100 W
02: 200 W
04: 400 W
08: 750 W
Function 2 C: RS485 communication,
Function 1
Signal input/Sink type (NPN transistor)
B: with circuit for regenerative resistor
Input power supply 1: Single phase AC100 to 120 V
3: 3-phase AC200 to 240 V
5: Single phase/3-phase AC200 to 240 V
－5－－4－
P13030001＊
Ex.:
Month of production
Year of production
(Lower 2 digits of AD year)
Production Date
20130301
Ex.:
month of Production
year of Production (AD year)
V: speed control
Consecutive
number
day of Production
Loading...