Panasonic M9RZ90GB4LG User Manual

English

Safety Precautions

Caution

Don't put an object or finger into the motor opening.

Don't turn off and on power so frequently.

Don't pull leadwires with an excessive force.

Don't use the equipment in highly intensive electric field.

Don't use the equipment under direct sunshine.

Don't use the equipment in an environment where electro-static voltage potentials may be produced.

Don't drop or cause topple over of something during transportation or installation.

Never attempt to perform modification, dismantle or repair.

Perform installation by taking into consideration the mass of the body and rated output of the product.

Adjust the motor ambient environmental condition to match the motor operating temperature and humidity.

Exactly follow the installing method and direction specified.

Connect a ground-fault interrupter, circuit breaker and replay to the brake control relay in series so that they are turned off upon emergency stop.

Test-run the securely fixed motor without loading to verify normal operation, and then connect it to the mechanical system.

Level of input voltage to peripheral devices should correspond to the motor rated voltage.

Provide protection device against idling of electro-magnetic brake or gear head, or grease leakage from gear head.

Don't place any obstacle object around the motor and peripheral, which blocks air passage.

Correctly run and arrange wiring.

Maintenance must be performed by an experienced personnel.

Always keep power disconnected when the power is not necessary for a long time.

Please observe safety precautions fully.

Failure to heed this instruction will result in electric shock or fire.

Failure to heed this instruction will result in fire, personal injury, malfunction or damage.

Failure to heed this instruction will cause fire, electric shock or personal injury.

Failure to heed these instructions will cause personal injury or fire.

Induced malfunction will cause malfunction or personal injury.

Failure to heed this instruction will result in personal injury or malfunction.

Failure to heed this instruction will result in fire, electric shock, personal injury or malfunction.

Failure to heed these requirements will result in personal injury or malfunction.

Missing of one of these devices will cause malfunction.

Operation using a wrong model or wrong wiring connection will result in personal injury.

Operation from a voltage outside the rated voltage will cause electric shock, personal injury or fire.

No protection will cause personal injury, damage, pollution or fire.

Temperature rise will cause burn injury or fire.

Wrong wiring will cause personal injury or electric shock.

Improper operation will cause personal injury.

1. Introduction

General

Thisis a compact AC geared-motor having multiple international standard certifications. To use this product for a prolonged period, read this manual thoroughly. This is designed for use in corporation with general purpose industrial devices. The product must

be handled by experienced personnel familiar with the product.

<note>

When export this product, follow statutory provisions of the destination country.

Unpacking

• Proceed as follows:

• First open the top of the packing and check the units for damage in transit.

• Check the motor nameplate for the model number, output, No. of poles, voltage, frequency,

etc. Do not use the product if it does not meet your specification (if you dare to use it, burn injury or fire may result).

• A single-phase motor comes with capacitor and capacitor cap. Check the rated capacitance and voltage on the nameplate. Do not use the accessory capacitor if it does not meet your specification (if you dare to use it, you may be injuried or may have fire).

• Gear head is optional.

• Check a gear ratio on the nameplate. Do not use it if it does not meet your specification (if you dare to use it, you may be injuried or may have fire).

Should you find any discrepancy in the product, consult your local dealer.

Scraps must be treated as industrial waste.

– 5 –– 4 –

English

1. Introduction

SUD

Model identification

Designation and rating information on the nameplate

• Below shows a sample of nameplate, a single-phase induction motor (90 W). Note: Format of nameplate is not common to all models.

Part number

Motor type

Rated power

Number of poles

Weight

Rated voltage

Model No.

SINGLE PHASE INDUCTION MOTOR 4P 90W S2(30min) THERMAL130(B)G-B IP20 T.P.

Matsushita Electric Industrial Co.,Ltd.

Made in Japan

• SINGLE PHASE INDUCTION MOTOR Capacitor motor : Induction motor, Reversible motor

• THREE PHASE INDUCTION MOTOR : Three phase Induction motor

• Below shows a sample of gear head Sq.90mm 1/18

Gear head part

number

M9RZ90GB4LG

VHz A min 100 50 1.8 1250 100 60 1.9 1575

BRAKE TORQUE 0.39N A030502AMB.40˚C 3.7kg

6721

Lot number

Model No.

–1

32(250V) 32(250V)

•

SUD

MZ9G18B

Matsushita Electric Industrial Co.,Ltd.

Designation of lot number

6 7 21

Manufacturing day

Manufacturing month:

1=Jan., 2=Feb., ..... 9= Sept., X=Oct., Y=Nov., Z= Dec.

Manufacturing year:

the last digit of manufacturing year (e.g. 6 represents the last digit of 2006)

Made in Japan

6721

Rated current

µF

Lot number

Rated speed

Capacitor spec. (capacitor rated voltage)

Description of model number

Motor

M9 RZ90GB4LG

1, 2 3 4 5,6 7 8 9 10 11

Frame size

M6: Sq.60mm M7: Sq.70mm M8: Sq.80mm M9: Sq.90mm

Type

X:40W or less Z:60W or more

Induction motor and reversible motor are single phase motor.

Type

1:Induction motor R:

Reversible

M:Three phase

Induction motor

motor

Output

6 : 6W 15 : 15W 25 : 25W 40 : 40W 60 : 60W 90 : 90W

A5 : 150W

Shaft

G:Pinion S:Round

Option

K: Seal connector B: Electromagnetic brake V: Variable speed (with TG)

No. of poles

2 : 2 4 : 4

L:100V Y:200V (Single phase)

C: 380/400V (Three phase) D: 110/115V G: 220/230V (Single phase)

G: International standards certified

Gear head

MZ 9G18B

1, 2 3 4 5, 6 7 8

Type

Without hinge 40 W or less

Without hinge 60 W or 90 W

With hinge 60 W or 90 W

Without hinge High torque 60 W or 90 W

With hinge High torque 60 W or 90 W

Gear head

Size

6 : Sq.60mm 7 : Sq.70mm 8 : Sq.80mm 9 : Sq.90mm

B:Ball bearing M:Metal bearing

XB : Intermediate gear head

(reduction ratio 1/10)

R:Right-angle gear head

Applicable only to Sq.90 mm: MX and MZ

Reduction ratio

Example Symbol : 18 Reduction ratio : 1/18

<Note>

Gear head is optional. For further information refer to your local dealer.

– 7 –– 6 –

Bearing

Rated voltage

200/220/230V

Classification

Thin gear head

A:Sq.60mm, Sq.70mm

if it is 1/25 or less.

: Sq.80mm, Sq.90mm

open Applicable only to reduction ratio 1/25 or less gear head.

(Three phase)

+ 1 hidden pages