Panasonic KX-TGD310NZ, KX-TGD312NZ, KX-TGD320NZ, KX-TGD322NZ Operating Instructions Manual
Operating Instructions
Digital Cordless Phone
Model No.
KX-TGD310NZ
KX-TGD312NZ
Digital Cordless Answering System
Model No.
KX-TGD320NZ
KX-TGD322NZ
Model shown is KX-TGD310.
Before initial use, see “Getting Started”
on page 9.
Thank you for purchasing a Panasonic product.
Please read these operating instructions before using the unit and save them for
future reference.
0303_TGD3xxNZ(en-en)_ver002.pdf 1 2015/03/03 10:28:02
Introduction
Model composition .......................................3
Accessory information ..................................3
Important Information
For your safety .............................................5
Important safety instructions ........................6
For best performance ...................................7
Other information .........................................7
Specifications ...............................................8
Getting Started
Setting up .....................................................9
Controls ......................................................11
Display icons ..............................................12
Turning the power on/off ............................13
Language setting
........................................13
Date and time .............................................13
Recording your greeting message .............14
Other settings .............................................14
Making/Answering Calls
Making calls ...............................................15
Answering calls ..........................................15
Useful features during a call .......................15
Intercom .....................................................17
Key lock ......................................................17
Power backup operation ............................17
Phonebook
Phonebook .................................................19
Speed dial ..................................................20
Programming
Menu list .....................................................22
Alarm ..........................................................28
Do not disturb mode ...................................28
Nuisance call block ....................................29
Baby monitor ..............................................30
Other programming ....................................32
Registering a unit .......................................33
Caller ID Service
Using Caller ID service ...............................36
Caller list ....................................................36
Answering System
Answering system ......................................38
Turning the answering system on/off .........38
Greeting message ......................................38
Listening to messages ...............................39
Advanced new message alerting
features ......................................................40
Remote operation
.......................................42
Answering system settings .........................43
Useful Information
Voicemail service .......................................45
Character entry ..........................................45
Error messages ..........................................47
Troubleshooting .........................................48
Warranty .....................................................52
Index
Index...........................................................53
2
Table of Contents
0303_TGD3xxNZ(en-en)_ver002.pdf 2 2015/03/03 10:28:02
Model composition
n KX-TGD310 series n KX-TGD320 series
R M
odel shown is KX-TGD312. R Model shown is KX-TGD322.
Series Model No.
Base unit Handset
Part No. Part No. Quantity
KX-TGD310
s
eries
KX-TGD310 KX-TGD310 KX-TGDA30 1
KX-TGD312 KX-TGD310 KX-TGDA30 2
KX-TGD320
s
eries
KX-TGD320 KX-TGD320 KX-TGDA30 1
KX-TGD322 KX-TGD320 KX-TGDA30 2
Accessory information
Supplied accessories
No. Accessory item/Part number
Quantity
KX-TGD310
K
X-TGD320
KX-TGD312
K
X-TGD322
A AC adaptor for base unit/PNLV226AL 1 1
B Telephone line cord 1 1
C
Rechargeable batteries
*
1
2 4
D
Handset cover
*
2
1 2
E Charger – 1
F AC adaptor for charger/PNLV233AL – 1
*1 See page 4 for replacement battery information.
*
2 The handset cover comes attached to the handset.
A
B C D E F
3
Introduction
0303_TGD3xxNZ(en-en)_ver002.pdf 3 2015/03/03 10:28:02
Additional/replacement accessories
Please contact your nearest Panasonic dealer for sales information.
Accessory item Model number/Specifications
Rechargeable
b
atteries
*1
Battery type:
– Nickel metal hydride (Ni-MH)
– 2 x AAA (R03) size for each handset
– 1.2 V
– Minimum amperage of 550 mAh
DECT repeater KX-A405, KX-A406
Key finder
KX-TGA20AZ
*
2
*1 Replacement batteries may have a different capacity from that of the supplied batteries.
W
e recommend using Panasonic rechargeable batteries.
*2 By registering the key finder (4 max.) to a Panasonic Digital Cordless Phone and attaching it
to an easy-to-lose item in advance, you can locate and find the mislaid item to which the key
finder is attached. Please visit our Web site:
www.panasonic.net/pcc/products/telephone/p/tga20/
Please contact Panasonic or authorised sales department for availability of key finder in your
area.
Other information
R D
esign and specifications are subject to change without notice.
R The illustrations in these instructions may vary slightly from the actual product.
Expanding your phone system
Handset (optional): KX-TGDA30AZ
You can expand your phone system by
r
egistering optional handsets (6 max.) to a
single base unit.
R Optional handsets may be a different
colour from that of the supplied handsets.
4
Introduction
0303_TGD3xxNZ(en-en)_ver002.pdf 4 2015/03/03 10:28:02
For your safety
T
o prevent severe injury and loss of life/
property, read this section carefully before
using the product to ensure proper and safe
operation of your product.
WARNING
Power connection
R U
se only the power source marked on the
product.
R Do not overload power outlets and
extension cords. This can result in the risk
of fire or electric shock.
R Completely insert the AC adaptor/power
plug into the power outlet. Failure to do so
may cause electric shock and/or excessive
heat resulting in a fire.
R Regularly remove any dust, etc. from the
AC adaptor/power plug by pulling it from
the power outlet, then wiping with a dry
cloth. Accumulated dust may cause an
insulation defect from moisture, etc.
resulting in a fire.
R Unplug the product from power outlets if it
emits smoke, an abnormal smell, or makes
an unusual noise. These conditions can
cause fire or electric shock. Confirm that
smoke has stopped emitting and contact an
authorised service centre.
R Unplug from power outlets and never touch
the inside of the product if its casing has
been broken open.
R Never touch the plug with wet hands.
Danger of electric shock exists.
Installation
R T
o prevent the risk of fire or electrical
shock, do not expose the product to rain or
any type of moisture.
R Do not place or use this product near
automatically controlled devices such as
automatic doors and fire alarms. Radio
waves emitted from this product may cause
such devices to malfunction resulting in an
accident.
R D
o not allow the AC adaptor or telephone
line cord to be excessively pulled, bent or
placed under heavy objects.
Operating safeguards
R U
nplug the product from power outlets
before cleaning. Do not use liquid or
aerosol cleaners.
R Do not disassemble the product.
R Do not spill liquids (detergents, cleansers,
etc.) onto the telephone line cord plug, or
allow it to become wet at all. This may
cause a fire. If the telephone line cord plug
becomes wet, immediately pull it from the
telephone wall socket, and do not use.
Medical
R C
onsult the manufacturer of any personal
medical devices, such as pacemakers or
hearing aids, to determine if they are
adequately shielded from external RF
(radio frequency) energy. (The product
operates in the frequency range of
1.88 GHz to 1.90 GHz, and the RF
transmission power is 250 mW (max.).)
R Do not use the product in health care
facilities if any regulations posted in the
area instruct you not to do so. Hospitals or
health care facilities may be using
equipment that could be sensitive to
external RF energy.
CAUTION
Installation and location
R Never install telephone wiring during an
electrical storm.
R Never install telephone line sockets in wet
locations unless the socket is specifically
designed for wet locations.
R Never touch uninsulated telephone wires or
terminals unless the telephone line has
been disconnected at the network interface.
R Use caution when installing or modifying
telephone lines.
R The AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is installed near the product and is
easily accessible.
5
Important Information
0303_TGD3xxNZ(en-en)_ver002.pdf 5 2015/03/03 10:28:03
R T
his product is unable to make calls when:
– the handset batteries need recharging or
have failed.
– there is a power failure.
– the key lock feature is turned on.
Battery
R W
e recommend using the batteries noted
on page 4. USE ONLY rechargeable
Ni-MH batteries AAA (R03) size.
R Do not mix old and new batteries.
R Do not open or mutilate the batteries.
Released electrolyte from the batteries is
corrosive and may cause burns or injury to
the eyes or skin. The electrolyte is toxic and
may be harmful if swallowed.
R Exercise care when handling the batteries.
Do not allow conductive materials such as
rings, bracelets, or keys to touch the
batteries, otherwise a short circuit may
cause the batteries and/or the conductive
material to overheat and cause burns.
R Charge the batteries provided with or
identified for use with this product only, in
accordance with the instructions and
limitations specified in this manual.
R Only use a compatible base unit (or
charger) to charge the batteries. Do not
tamper with the base unit (or charger).
Failure to follow these instructions may
cause the batteries to swell or explode.
General notices
R T
his equipment will be inoperable when
mains power fails.
R When a failure occurs which results in the
internal parts becoming accessible,
disconnect the power supply cord
immediately and return this unit to an
authorised service centre.
R Disconnect the telecom connection before
disconnecting the power connection prior to
relocating the equipment, and reconnect
the power first.
R No “111” or other calls can be made from
this device during a mains power failure.
R This equipment shall not be set to make
automatic calls to the Telecom “111”
Emergency Service.
R T
o minimise the possibility of lightning
damage, when you know that a
thunderstorm is coming, we recommend
that you:
– Unplug the telephone line cord from the
phone socket.
– Unplug the AC adaptor from the AC
power outlet.
R The earpiece on the handset is magnetised
and may retain small metallic objects.
R The unit’s answering system only responds
to Distinctive Alert cadence(s) DA1 and
DA3.
R Not all telephones will respond to incoming
ringing when connected to the extension
socket.
R This equipment may not provide for the
effective hand-over of a call to another
device connected to the same line.
R The grant of a Telepermit for any item of
terminal equipment indicates only that
Telecom has accepted that the item
complies with minimum conditions for
connection to its network. It indicates no
endorsement of the product by Telecom,
nor does it provide any sort of warranty.
Above all, it provides no assurance that any
item will work correctly in all respects with
another item of Telepermitted equipment of
a different make or model, nor does it imply
that any product is compatible with all of
Telecom’s network services.
Important notice:
R Under power failure conditions, this
telephone may not operate. Please ensure
that a separate telephone, not dependent
on local power, is available for emergency
use.
Important safety
i
nstructions
When using your product, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock, and
injury to persons, including the following:
1. Do not use this product near water for
example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet
basement or near a swimming pool.
6
Important Information
0303_TGD3xxNZ(en-en)_ver002.pdf 6 2015/03/03 10:28:03
2. Avoid using a telephone (other than a
c
ordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
3. Do not use the telephone to report a gas
leak in the vicinity of the leak.
4. Use only the power cord and batteries
indicated in this manual. Do not dispose of
batteries in a fire. They may explode.
Check with local codes for possible special
disposal instructions.
SAVE THESE INSTRUCTIONS
For best performance
Base unit location/avoiding noise
T
he base unit and other compatible Panasonic
units use radio waves to communicate with
each other.
R For maximum coverage and noise-free
communications, place your base unit:
– at a convenient, high, and central
location with no obstructions between
the handset and base unit in an indoor
environment.
– away from electronic appliances such as
TVs, radios, personal computers,
wireless devices, or other phones.
– facing away from radio frequency
transmitters, such as external antennas
of mobile phone cell stations. (Avoid
putting the base unit on a bay window or
near a window.)
R Coverage and voice quality depends on the
local environmental conditions.
R If the reception for a base unit location is
not satisfactory, move the base unit to
another location for better reception.
Environment
R K
eep the product away from electrical noise
generating devices, such as fluorescent
lamps and motors.
R The product should be kept free from
excessive smoke, dust, high temperature,
and vibration.
R The product should not be exposed to
direct sunlight.
R D
o not place heavy objects on top of the
product.
R When you leave the product unused for a
long period of time, unplug the product from
the power outlet.
R The product should be kept away from heat
sources such as radiators, cookers, etc. It
should not be placed in rooms where the
temperature is less than 0 °C or greater
than 40 °C. Damp basements should also
be avoided.
R The maximum calling distance may be
shortened when the product is used in the
following places: Near obstacles such as
hills, tunnels, underground, near metal
objects such as wire fences, etc.
R Operating the product near electrical
appliances may cause interference. Move
away from the electrical appliances.
Routine care
R W
ipe the outer surface of the product
with a soft moist cloth.
R Do not use benzine, thinner, or any
abrasive powder.
Other information
C
AUTION: Risk of explosion if battery is
replaced by an incorrect type. Dispose of used
batteries according to the instructions.
Notice for product disposal, transfer,
or return
R This product can store your private/
confidential information. To protect your
privacy/confidentiality, we recommend that
you erase information such as phonebook
or caller list entries from the memory before
you dispose of, transfer, or return the
product.
7
Important Information
0303_TGD3xxNZ(en-en)_ver002.pdf 7 2015/03/03 10:28:03
Information on Disposal in other
C
ountries outside the European Union
These symbols are only valid in the European
U
nion. If you wish to discard these items,
please contact your local authorities or dealer
and ask for the correct method of disposal.
Note for the battery removal
p
rocedure
Refer to “Battery installation” on page 9.
Specifications
R S
tandard:
GAP (Generic Access Profile)
R Frequency range:
1.88 GHz to 1.90 GHz
R RF transmission power:
Approx. 10 mW (average power per
channel)
R Power source:
220–240 V AC, 50/60 Hz
R Power consumption:
Base unit*1:
Standby: Approx. 0.52 W
Maximum: Approx. 2.70 W
Base unit*2:
Standby: Approx. 0.57 W
Maximum: Approx. 2.70 W
Charger:
Standby: Approx. 0.16 W
Maximum: Approx. 1.80 W
R Operating conditions:
0 °C–40 °C, 20 %–80 % relative air
humidity (dry)
*1 KX-TGD310 series: page 3
*2 KX-TGD320 series: page 3
8
Important Information
0303_TGD3xxNZ(en-en)_ver002.pdf 8 2015/03/03 10:28:03
Setting up
Connections
n
Base unit
Connect the AC adaptor to the unit by
p
ressing the plug firmly.
Fasten the cord by hooking it.
Connect the AC adaptor to the power
o
utlet.
Connect the telephone line cord to the
u
nit, then to the telephone line socket
until you hear a click.
A DSL/ADSL filter (not supplied) is
r
equired if you have a DSL/ADSL service.
1
2
3
4
45
Note:
R U
se only the supplied Panasonic AC
adaptor PNLV226AL.
R Use only the supplied telephone line cord.
n
Charger
Connect the AC adaptor plug to the unit
u
ntil you hear a click.
Connect the AC adaptor to the power
o
utlet.
1
2
Note:
R U
se only the supplied Panasonic AC
adaptor PNLV233AL.
Battery installation
R U
SE ONLY rechargeable Ni-MH batteries
AAA (R03) size (
1
).
R D
o NOT use alkaline/manganese/Ni-Cd
batteries.
R Confirm correct polarities (
, ).
1
R F
ollow the directions on the display to set
up the unit.
9
Getting Started
0303_TGD3xxNZ(en-en)_ver002.pdf 9 2015/03/03 10:28:03
Battery charging
Charge for about 7 hours.
R Confirm “Charging” is displayed (1).
R W
hen the batteries are fully charged,
“Fully Charged” is displayed.
1
Note when setting up
Note for connections
R T
he AC adaptor must remain connected at
all times. (It is normal for the adaptor to feel
warm during use.)
R The AC adaptor should be connected to a
vertically oriented or floor-mounted AC
outlet. Do not connect the AC adaptor to a
ceiling-mounted AC outlet, as the weight of
the adaptor may cause it to become
disconnected.
R The unit is not designed to be used with
rotary/pulse dialling services.
R The unit’s answering system will not
answer incoming calls on your FaxAbility
number. (KX-TGD320 series: page 3)
Note for battery installation
R U
se the supplied rechargeable batteries.
For replacement, we recommend using the
Panasonic rechargeable batteries noted on
page 4, 6.
Note for battery charging
R I
t is normal for the handset to feel warm
during charging.
R Clean the charge contacts of the handset,
base unit, and charger with a soft and dry
cloth once a month. Before cleaning the
unit, disconnect from power outlets and any
t
elephone line cords. Clean more often if
the unit is exposed to grease, dust, or high
humidity.
Battery level
Icon Battery level
High
Medium
Low
Needs charging.
Panasonic Ni-MH battery
p
erformance (supplied batteries)
Operation Operating time
In continuous use 16 hours max.
Not in use (standby) 200 hours max.
Note:
R A
ctual battery performance depends on
usage and ambient environment.
10
Getting Started
0303_TGD3xxNZ(en-en)_ver002.pdf 10 2015/03/03 10:28:03
Controls
Handset
A A
B
B
G
H
I
J
F
K
D
C
A
E
Speaker
M N
(Talk)
Dial keypad
MZN
(SP-PHONE: Speakerphone)
Microphone
Receiver
Display
M N
(Power) MOFFN
MR
ECALLN MECON
ECO: Eco mode shortcut key
M N
(INTERCOM)
Charge contacts
n C
ontrol type
S
oft keys
By pressing a soft key, you can select the
feature shown directly above it on the
display.
(Example: MENU, OK, etc.)
N
avigator key
Navigator keys functions as follows.
– MDN, MCN, MFN, or MEN: Scroll through
various lists and items.
– VOL. (Volume: MDN or MCN): Adjust the
receiver or speaker volume while talking.
– MFN W: View the phonebook entry.
– MEN REDIAL: View the redial list.
– MCN CID (Caller ID): View the caller list.
Base unit
n KX-TGD310 series: page 3
B
A
Charge contacts
M N
(Locator)
R You can locate a misplaced handset
by pressing M
N.
11
Getting Started
0303_TGD3xxNZ(en-en)_ver002.pdf 11 2015/03/03 10:28:03
n
KX-TGD320 series: page 3
C D E
H I KF
B
A
G J
Charge contacts
Speaker
M N
(Locator)
R You can locate a misplaced handset
by pressing M
N.
ME
RASEN
MjN/M
kN (VOLUME: Volume up/down)
M N
(Repeat)
ANSWER ON/OFF indicator
MA
NSWER ON/OFFN
M N
(PLAY/STOP)
Message indicator
M N
(Skip)
Display icons
Handset display items
Item Meaning
Range status: The more bars
v
isible, the closer the handset
is to the base unit.
Out of base unit range
Item Meaning
Security for phone calls is set
t
o “Enhanced”. (page 33)
Paging, intercom mode
Z
Speakerphone is on.
(
page 15)
The line is in use.
R When flashing slowly: The
call is put on hold.
R When flashing rapidly: An
incoming call is now being
received.
Missed call
*
1
(page 36)
Eco mode is set to “E
co”.
(page 14)
The LCD and key backlight is
o
ff. (page 25)
R When displayed next to the
battery icon: Answering
system is on.*2 (page 38)
R When displayed with a
number: New messages
have been recorded.
*2
(page 40)
“G
reeting Only” is
selected. Caller messages
are not recorded.
*2
(page 44)
Battery level
Alarm is on. (page 28)
Privacy mode is on.
(
page 26)
Ringer volume is off.
(
page 24)
Do not disturb mode is on.
(
page 29)
Nuisance call blocked.
*
1
(page 29)
New voicemail message
r
eceived.*3 (page 45)
Baby monitor is activated.
T
he name/number displayed
next to the icon indicates the
monitoring unit. (page 30)
12
Getting Started
0303_TGD3xxNZ(en-en)_ver002.pdf 12 2015/03/03 10:28:03
Item Meaning
Line in
u
se
Someone is using the line.
IN USE
Answering system is being
u
sed by another handset or
the base unit.
*2
*1 Caller ID subscribers only
*
2 KX-TGD320 series: page 3
*3 Voicemail subscribers only
Handset soft key icons
Icon Action
OK Accepts the current selection.
Temporarily turns off the ringer
f
or incoming calls. (page 15)
W Opens the phonebook.
Turns the key lock feature off.
(
page 17)
n
When you select a language other than
English
Icon Action
Returns to the previous screen or
outside call.
Displays the menu.
Makes a call.
Places a call on hold.
Allows you to edit phone
n
umbers.
Adds new entry.
Displays the phonebook search
m
enu.
Stops alarm.
Snooze button on the alarm.
Selects entries or handsets.
n
Stops recording or playback.
*
1
Stores phone numbers.
Erases the selected item.
Allows you to make an intercom
c
all.
Icon Action
C Erases a number/character.
Puts the call on mute.
*1 KX-TGD320 series: page 3
Turning the power on/off
P
ress M
N
for about 2 seconds.
Language setting
Display language
1 MM
ENUN#110
2 MbN: Select your desired language. a
MOKN
3 MOFFN
Date and time
1 MM
ENUN#101
2 Enter the current date, month, and year.
a MOKN
Example: 12 July, 2015
12 07 15
3 Enter the current hour and minute.
Example: 9:30
09 30
R You can select 24-hour or 12-hour
clock format (“AM” or “PM”) by
pressing *.
4 MOKN a MOFFN
13
Getting Started
0303_TGD3xxNZ(en-en)_ver002.pdf 13 2015/03/03 10:28:03
Recording your greeting
m
essage
Available for:
K
X-TGD320 series (page 3)
You can record your own greeting message
i
nstead of using a pre-recorded greeting
message. See page 38 for details.
1 MMENUN#302
2 MbN: “Yes” a MOKN
3 Record a greeting message. a MSTOPN
a MOFFN
Other settings
Eco mode setting
You can select the desired eco mode setting
by pressing MECON.
The following settings are available for eco
mode.
– “Eco”: Reduces the base unit transmission
power by up to 90 % in standby mode.
When this setting is selected, is
d
isplayed on the handset display instead of
.
– “E
co Off” (default setting): Turns off eco
mode.
When this setting is selected,
is not
d
isplayed in the handset display.
Note:
R When there is another cordless phone in
use nearby, the base unit transmission
power may not be reduced.
R When eco mode is active, the range of the
base unit is reduced in standby mode.
R If you set repeater mode to “On”
(page 34):
– Eco mode is disabled.
– “Eco Mode” is not displayed in the
display menu (page 25).
14
Getting Started
0303_TGD3xxNZ(en-en)_ver002.pdf 14 2015/03/03 10:28:04
Making calls
1 L
ift the handset and dial the phone
number.
R To correct a digit, press MCLEARN.
2 M
N
3 W
hen you finish talking, press MOFFN or
place the handset on the base unit or
charger.
Using the speakerphone
1 D
ial the phone number and press MZN.
R Speak alternately with the other party.
2 When you finish talking, press MOFFN.
Note:
R To switch back to the receiver, press MZN/
M
N.
Adjusting the receiver or speaker
v
olume
Press MDN or MCN repeatedly while talking.
Making a call using the redial list
T
he last 10 phone numbers dialled are stored
in the redial list (each 24 digits max.).
1 MEN REDIAL
2 MbN: Select the desired entry.
3 M
N
Erasing a number in the redial list
1 MEN
REDIAL
2 MbN: Select the desired entry. a
MERASEN
3 MbN: “Yes” a MOKN a MOFFN
Pause (for PBX/long distance service
u
sers)
A pause is sometimes required when making
calls using a PBX or long distance service.
When storing a calling card access number
and/or PIN in the phonebook, a pause is also
needed (page 20).
Example: I
f you need to dial the line access
number “0” when making outside calls with a
PBX:
1 0 a MDN (Pause)
2 Dial the phone number. a M
N
N
ote:
R A 3 second pause is inserted each time MDN
(Pause) is pressed.
Answering calls
1 Lift the handset and press M N
or MZN
when the unit rings.
2 When you finish talking, press MOFFN or
place the handset on the base unit or
charger.
Any key answer: You can answer the call by
pressing any dial key.
Auto talk: You can answer calls simply by
lifting the handset (page 25).
Temporary handset ringer off: You can turn
the ringer off temporarily by pressing M
N.
Adjusting the ringer volume
Handset
P
ress MDN or MCN repeatedly to select the
desired volume while ringing.
Base unit
*
1
*1 KX-TGD320 series: page 3
Press MjN or MkN repeatedly to select the
desired volume while ringing.
R To turn the ringer off, press and hold MkN
until the unit beeps.
Useful features during a
c
all
Hold
1 P
ress MMENUN during an outside call.
2 MbN: “Hold” a MOKN
15
Making/Answering Calls
0303_TGD3xxNZ(en-en)_ver002.pdf 15 2015/03/03 10:28:04
3 T
o release hold, press M
N.
N
ote:
R After holding for 10 minutes, the call is
disconnected.
Mute
1 P
ress MMUTEN during a call.
2 To return to the call, press MMUTEN.
Note:
R MMUTEN is a soft key visible on the display
during a call.
Recall/flash
MRECALLN allows you to use the special
features of your host PBX such as transferring
an extension call, or accessing optional
telephone services.
Note:
R To change the recall/flash time, see
page 26.
For Call Waiting or Call Waiting
C
aller ID service users
To use call waiting or Call Waiting Caller ID,
you must first subscribe with your phone
service provider.
This feature allows you to receive calls while
you are already talking on the phone. If you
receive a call while on the phone, you will hear
a call waiting tone.
If you subscribe to both Caller ID and Call
Waiting with Caller ID services, the 2nd
caller’s information is displayed after you hear
the call waiting tone on the handset.
1 Press MRECALLN to answer the 2nd call.
2 To switch between calls, press
MRECALLN.
Note:
R Please contact your phone service provider
for details and availability of this service in
your area.
Handset equalizer
This feature clarifies the voice of the person
you are talking to, producing a more
natural-sounding voice that is easier to hear
and understand.
1 Press MMENUN while talking.
2 MbN: “Equalizer” a MOKN
3 MbN: Select the desired setting.
4 Press MOKN to exit.
Note:
R Depending on the condition and quality of
your telephone line, this feature may
emphasise existing line noise. If it becomes
difficult to hear, turn this feature off.
R This feature is not available while using the
speakerphone.
Call share
Y
ou can join an existing outside call.
To join the conversation, press M
N
when
the other handset is on an outside call.
Note:
R To prevent other users from joining your
conversations with outside callers, turn the
privacy mode on (page 26).
Transferring calls, conference
c
alls
Outside calls can be transferred or a
conference call with an outside party can be
made between 2 handsets in the same radio
cell.
1 During an outside call, press M
N.
W
hen 3 or more handsets are
registered:
MbN: Select the desired unit. a MOKN
2 Wait for the paged party to answer.
R If the paged party does not answer,
press MBACKN to return to the outside
call.
3 To complete the transfer:
Press MOFFN.
To establish a conference call:
16
Making/Answering Calls
0303_TGD3xxNZ(en-en)_ver002.pdf 16 2015/03/03 10:28:04
MM
ENUN a MbN: “Conference” a
MOKN
R To leave the conference, press MOFFN.
The other 2 parties can continue the
conversation.
R To put the outside call on hold:
MMENUN a MbN: “Hold” a MOKN
To resume the conference: MMENUN
a MbN: “Conference” a MOKN
R To cancel the conference: MMENUN a
MbN: “Stop Conference” a MOKN
You can continue the conversation
with the outside caller.
Intercom
Intercom calls can be made between handsets
in the same radio cell.
Note:
R When paging the handset, the paged
handset beeps for 1 minute.
R If you receive an outside call while talking
on the intercom, the interrupt tone sounds.
To finish intercom, press MOFFN. To answer
the call, press M N.
Making an intercom call
1 M N
W
hen 3 or more handsets are
registered:
MbN: Select the desired unit. a MOKN
2 When you finish talking, press MOFFN.
Answering an intercom call
1 P
ress M
N to answer the page.
2 When you finish talking, press MOFFN.
Turning auto intercom on/off
T
his feature allows the handset to answer
intercom calls automatically when it is called.
You do not need to press M
N. When this
feature is set to “On”, the monitoring handset
for the baby monitor feature (page 32) will
also answer baby monitor calls automatically.
T
he default setting is “Off”.
1 MMENUN#273
2 MbN: Select the desired setting. a MOKN
a MOFFN
Key lock
T
he handset can be locked so that no calls or
settings can be made. Incoming calls can be
answered, but all other functions are disabled
while key lock is on.
To turn key lock on, press MMENUN for about 3
seconds.
R To turn key lock off, press M
N
for about
3 seconds.
Note:
R Calls to emergency numbers cannot be
made until key lock is turned off.
Power backup operation
W
hen a power failure occurs, the charged
handset temporarily supplies power to the
base unit (power backup mode). This allows
you to make and receive calls using a handset
during a power failure. The base unit will not
perform any other functions. You can program
“Power Failure” and the default setting is
“Auto” (page 26).
Important:
R If a handset is not placed on the base unit
when a power failure occurs, “Base no
power Press OFF” is displayed. After
pressing MOFFN on the handset, place it on
the base unit to start power backup mode.
R Power backup mode will not work if the
battery level of the power supplying
handset is
/ .
R D
o not lift the power supplying handset
from the base unit during power backup
mode.
17
Making/Answering Calls
0303_TGD3xxNZ(en-en)_ver002.pdf 17 2015/03/03 10:28:04
Loading...