Panasonic KX-TGA230W, KX-TGA230B User Manual

– 1 –

For assistance, please call: 1-800-211-PANA(7262)

PQQX13421YA-AK S0702-1072

Installation Manual

PLEASE READ BEFORE USE AND SAVE.

KX-TGA230B/KX-TGA230W is the optional cordless handset for the
KX-TG2352W/KX-TG2382B.
This installation manual only describes the steps necessary to start up the
handset. Please read the KX-TG2352W/KX-TG2382B operating instructions for
further details.

2.4GHz Expandable Cordless Handset

Model No.

KX-TGA230B/KX-TGA230W

Charger Unit ...................................one

Charger Order No. PQLV30017ZB (Black)

Order No. PQLV30017ZW (White)

AC Adaptor

Order No. PQLV2Z(PQLV2

)

Handset Cover................................one

Order No. PQKK10131Z3 (Black)
Order No. PQKK10131Z2 (White)

Battery ...............................one

Order No. N4HHGMB00001

(HHR-P103)

Belt Clip .............................one

Order No. PQKE10352Z3 (Black)
Order No. PQKE10352Z2 (White)

Accessories (included) For extra orders, call 1-800-332-5368.

Installing the battery

Insert the battery into the handset as shown, matching the correct polarity (#). Press
the battery down until it fits securely into the compartment ($). Close the cover.

Installation!

Connecting the AC adaptor

•USE ONLY WITH Panasonic AC ADAPTOR PQLV2 (Order No. PQLV2Z).

•The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel

warm during use.)

AC Adaptor

Power Outlet
(AC 120 V, 60 Hz)

2

1

Charging the battery

Place the handset on the charger and charge for
about 15 hours before initial use.

• The CHARGE indicator will light, a beep will sound
and “Charging” will be displayed.

• Recharge the battery when:

– “

Recharge” is displayed,

– “” flashes on the display, or
– the handset beeps intermittently while it is in use.

• If the battery has been discharged, the handset will

display “Charge for 15h” when you place the
handset on the charger. The handset will not work.
Keep charging until fully charged.

Charge Contacts

CHARGE
Indicator

Handset battery information

After your Panasonic battery is fully charged:

Operation Operating time

While in use (TALK)

While not in use (Standby)

• Clean the charge contacts of the handset and the charger with a soft, dry cloth

once a month. Clean more often if the unit is subject to grease, dust or high
humidity. Otherwise the battery may not charge properly.

Up to 4 hours

Up to 7 days

Belt Clip!

You can hang the handset on your belt or pocket using the belt clip.

To attach the belt clip

To remove the belt clip

– 2 –

Registration!

This cordless handset must be registered at the KX-TG2352W/KX-TG2382B
base unit. The handset will be assigned the extension number at registration.
Only one handset can be registered at a time.

Make sure the base unit and the other handsets are not being used.
Registration must be completed within 1 minute.

CHARGE Indicator

HANDSET LOCATOR (ALL)

•The illustration of the base unit is the KX-TG2352W.

The handset display shows the instructions as shown
on the right.

Base unit:

1

Press HANDSET LOCATOR (ALL) until the
CHARGE indicator flashes.

Handset:

2

#Press á.

$Wait until a long beep sounds and the display

shows the registered number. The registration
will be then complete.

•The registered number “[1]” to “[3]” is shown on the top right of
the display.

•

You can stop registration by pressing (OFF) on the handset and
pressing HANDSET LOCATOR (ALL) on the base unit.

•After you register the handset to the base unit, please confirm that the other (first one and
second one) pre-registered handsets display “Talk” by pressing . If one of the
handsets does not display “Talk”, re-register that handset to the base unit.

Press [ALL] on
base for 3 sec,
then press [

Handset

Registering

Ex. Extension number 3

Handset [3]

Registered

á

H

[3]

].

To cancel the handset registration, please see the KX-TG2352W/KX-TG2382B
Operating Instructions.

For assistance, please call: 1-800-211-PANA(7262)

– 3 –

Optional Headset!

Plugging a headset into the handset allows a hands-free phone conversation.
Please use only the Panasonic KX-TCA88 headset.
To order, call the accessories telephone number on page 1.

Connecting the headset

Open the headset jack cover, and connect the headset to the headset jack as
shown.

H

Headset Jack

Wall Mounting!

The charger can be wall mounted. Connect the AC adaptor. Install screws using
the wall template below. Mount the charger (#). Slide it down ($) then slide
down to the right (%) until it is secured.

2.45 cm

15

(

")

⁄

16

#

$

Screws

To Power
Outlet

– 4 –

%

Wall
Template

2.45 cm

15

(

")

⁄

16

FCC and Other Information!

WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST CALLS
TO EMERGENCY NUMBERS:

1) Remain on the line and briefly explain to the dispatcher the reason for the call.

2) Perform such activities in the off-peak hours, such as early morning or late evenings.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

Privacy of communications may not be ensured when using this phone.

CAUTION:

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.

Note:

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

Operating near 2.4GHz electrical appliances may cause interference. Move away from
the electrical appliances.

CAUTION:

To comply with FCC RF exposure requirements, the handset should be carried with the
specific belt-clip provided for the handset to ensure compliance. Other non-tested belt­clips or similar body-worn accessories may not comply, therefore, should be avoided.

This equipment is hearing aid compatible as defined by the FCC in 47 CFR Section

68.316.

When you hold the phone to your ear, noise might be heard in your Hearing Aid. Some
Hearing Aids are not adequately shielded from external RF (radio frequency) energy. If
noise occurs, use an optional headset accessory or the speakerphone option (if
applicable) when using this phone. Consult with your audiologist or Hearing Aid
manufacturer about the availability of Hearing Aids which provide adequate shielding to
RF energy commonly emitted by digital devices.

For assistance, please call: 1-800-211-PANA(7262)

– 5 –

CAUTION:

To reduce the risk of fire or injury to persons, read and follow these instructions.

1.Use only the battery(ies) specified.

2.Do not dispose of the battery(ies) in a fire. They may explode. Check with local waste
management codes for special disposal instructions.

3.Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may
cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.

4.Exercise care in handling batteries in order not to short the battery to conductive
materials such as rings, bracelets, and keys. The battery and/or conductor may
overheat and cause burns.

5.Charge the battery(ies) provided with or identified for use with this product only in
accordance with the instructions and limitations specified in this manual.

A nickel metal hydride battery powers that is recyclable the
product you have purchased.
Please call 1-800-8-BATTERY for information on how to
recycle this battery.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR ANY TYPE OF MOISTURE.

•The AC adaptor is used as the main disconnect device, ensure that the AC

outlet is located/installed near the unit and is easily accessible.

Panasonic World Wide Web address: http://www.panasonic.com

for customers in the USA or Puerto Rico

Panasonic’s e-mail address for customer inquiries:
[e-mail]

Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America

One Panasonic Way, Secaucus, New Jersey 07094

Panasonic Sales Company,
Division of Matsushita Electric of Puerto Rico, Inc.

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park
Carolina, Puerto Rico 00985

– 6 –

If you need assistance with the set-up or operation,
please call 1-800-211-PANA(7262)

Unidad portátil inalámbrica de 2.4 GHz expandible

$

#

%

Modelo

KX-TGA230B/KX-TGA230W

Manual de instalación

LEA ESTAS INSTRUCCIONES ANTES DE LA UTILIZACIÓN Y
GUÁRDELAS.

La KX-TGA230B/KX-TGA230W es una unidad portátil opcional para el
KX-TG2352W/KX-TG2382B.
Este manual de instalación describe únicamente los pasos necesarios para
iniciar el funcionamiento de la unidad portátil. Lea las instrucciones de
funcionamiento del KX-TG2352W/KX-TG2382B para obtener más detalles.

Accesorios (incluidos)
Para solicitar accesorios extra, llame al

Unidad de carga ...................................1

Cargador

Adaptador de CA

Cubierta de la unidad portátil................1

N.° de pedido PQKK10131Z3 (Negro)
N.° de pedido PQKK10131Z2 (Blanco)

N.° de pedido PQLV30017ZB
N.° de pedido PQLV30017ZW
N.° de pedido

PQLV2Z (PQLV2)

Instalación!

Conexión del adaptador de CA

Adaptador de CA

1-800-332-5368.

Batería .................................1

(Negro)

(Blanco)

N

.° de pedido N4HHGMB00001

Presilla para el cinturón .......1

N.° de pedido
N.° de pedido

(HHR-P103)

PQKE10352Z3
PQKE10352Z2

Tomacorriente
(CA 120 V, 60 Hz)

(Negro)
(Blanco)

•USE UNICAMENTE EL ADAPTADOR DE CA PQLV2 de Panasonic (N.° de pedido
PQLV2Z).

•El adaptador de CA deberá permanecer conectado en todo momento. (Durante la
utilización es normal que se caliente el adaptador.)

Instalación de la batería

Inserte la batería en la unidad portátil como se muestra ajustando en la
polaridad correcta (#). Presione la batería hacia abajo hasta que esté bien
instalada en el compartimiento ($). Una vez instalada, cierre la cubierta.

1

– (1) – – (2) –

2

Carga de la batería

$

#

%

Ponga la unidad portátil en la unidad de carga y
cárguela durante 15 horas aproximadamente antes
de utilizarla por primera vez.

• El indicador CHARGE se encenderá, sonará un pitido y
se visualizará “

• Cargue la batería cuando:
– se visualice “
– “” parpadee en el visor, o
– la unidad portátil emita pitidos intermitentemente

mientras esté siendo utilizada.

• Si la batería se ha descargado, la unidad portátil
visualizará “Charge for 15h” cuando la ponga en la
unidad de carga. La unidad portátil no funcionará. Deje
que se cargue.

Charging”.

Recharge” en la unidad portátil,

Contactos
de carga

Indicador
CHARGE

Información acerca de la batería de la unidad portátil

Después de que su batería Panasonic esté completamente cargada:

Operación Tiempo de operación

Mientras se utiliza (HABLAR)

Mientras no se utiliza (Espera)

• Limpie los contactos de carga de la unidad portátil y de la unidad de carga con un
paño suave y seco una vez al mes. Limpie con más frecuencia si la unidad está
expuesta a la grasa, el polvo o humedad alta. Si no, la batería tal vez no se cargue

correctamente.

Hasta 4 horas

Hasta 7 días

Utilización de la presilla para cinturón

Podrá colgar la unidad portátil en su cinturón o bolsillo utilizando la presilla para
cinturón.

Para colocar la presilla para cinturón Para quitar la presilla para cinturón

$

#

%

Registro!

Esta unidad portátil inalámbrica deberá ser registrada en la unidad base
KX-TG2352W/KX-TG2382B. El número de extensión de la unidad portátil será
asignado al hacer el registro.
Solamente podrá registrarse una unidad portátil cada vez.

Asegúrese de que la unidad base y las otras unidades portátiles no estén
siendo utilizadas. El registro deberá completarse antes de 1 minuto.

Indicador CHARGE

HANDSET LOCATOR (ALL)

•La ilustración de la unidad base es del KX-TG2352W.

El visor de la unidad portátil muestra las instrucciones
como se muestra a la derecha.

Unidad base:

1

Presione HANDSET LOCATOR (ALL) hasta que
el indicador CHARGE parpadee.

Press [ALL] on
base for 3 sec,
then press [

H

á

].

Unidad portátil:

2

#Presione á.

$Espere hasta que suene un pitido largo y el

visor muestre el número registrado. Entonces
se habrá completado el registro.

•El número de registro
superior derecha del visor.

•Podrá detener el registro presionando (OFF) en la unidad portátil
y presionando HANDSET LOCATOR (ALL) en la unidad base.

•Después de registrar la unidad portátil en la unidad base, confirme que las otras unidades
portátiles (la primera y segunda) registradas previamente visualizan “Talk” presionando

. Si una de las unidades portátiles no visualiza “Talk”, vuelva a registrar esa unidad

portátil en la unidad base.

Para cancelar el registro de la unidad portátil, consulte las instrucciones de
funcionamiento del KX-TG2352W/KX-TG2382B.

“[1]”a “[3]” se mostrará en la parte

– (3) –

Handset

Registering

Ej., Número de extensión 3

Handset [3]

Registered

[3]

Auricular opcional!

$

#

%

Enchufando un auricular opcional a la unidad portátil podrá conversar por teléfono
con las manos libres. Utilice solamente el auricular Panasonic KX-TCA88.
Para hacer el pedido, llame al número de teléfono para accesorios de la página 1.

Conexión del auricular

Abra la tapa de la toma para auricular y conecte el auricular a la toma para
auricular como se muestra.

H

Toma para auricular

Montaje en pared!

El cargador puede montarse en una pared. Conecte el adaptador de CA. Instale
los tornillos utilizando la plantilla para pared de abajo. Monte el cargador (#).
Deslícelo hacia abajo ($) y después hacia abajo y hacia la derecha (%) hasta
fijarlo en su sitio.

2.45 cm

15

(

")

⁄

16

Tornillos

A la toma
de corriente

– (4) –

PLANTILLA
PARA PARED

2.45 cm

15

(

")

⁄

16