Panasonic KX-TGA106 Operating Instructions

TGA106(e).fm Page 1 Monday, January 19, 2009 6:51 PM

Installation Manual

Additional Digital Cordless Handset

Model No. KX-TGA106

Thank you for purchasing a Panasonic product.

This unit is an additional handset compatible with the following
series of Panasonic Digital Cordless Phone: KX-TG1061
You must register this handset with your base unit before it can
be used. This installation manual describes only the steps
needed to register and begin using the handset. Please read
the base unit’s operating instructions for further details.

Charge the batteries for about 7 hours before initial use.

Please read this installation manual before using the unit and
save it for future reference.

For assistance, visit our website:
http://www.panasonic.com/help
for customers in the U.S.A. or
Puerto Rico.

PNQX1801YA DC1208SY1019

TGA106(e).fm Page 2 Monday, January 19, 2009 6:51 PM

Accessory information

Supplied accessories

Accessory item/Order number Quantity

Charger/PNWETGA106M 1

AC adaptor/PQLV219Z 1

Rechargeable batteries/HHR-4DPA
(Part No. HHR-55AAABU or N4DHYYY00004)

Handset cover*1/PNYNTGA641TR 1

Belt clip/PNKE1029Z1 1

*1 The handset cover comes attached to the handset.

Note:

LPlease read the base unit’s operating instructions for additional/

replacement accessories.

2

Setting up

Connections

Hooks

(120 V AC, 60 Hz)

Note:

LUse only the supplied Panasonic AC adaptor PQLV219.
LThe AC adaptor must remain connected at all times. (It is normal for

the adaptor to feel warm during use.)

2 For assistance, please visit http://www.panasonic.com/help

TGA106(e).fm Page 3 Monday, January 19, 2009 6:51 PM

Battery installation/Battery charge

Important:

LUse the supplied rechargeable batteries. For replacement, we

recommend using the Panasonic rechargeable batteries noted on
page 2.

LWipe the battery ends (S, T) with a dry cloth.
LAvoid touching the battery ends (S, T) or the unit contacts.
LConfirm correct polarities (S, T).
LUSE ONLY Ni-MH batteries AAA (R03) size.
LDo NOT use Alkaline/Manganese/Ni-Cd batteries.

Charge for about 7 hours.
LWhen the batteries are fully charged, the charge indicator goes off.

Confirm “Charging”

Rechargeable Ni-MH
ONLY

is displayed.

Note:

LIf the batteries are fully charged, but the operating time seems to be

shorter, clean the battery ends (S, T) and the charge contacts with a
dry cloth and charge again.

For assistance, please visit http://www.panasonic.com/help 3

TGA106(e).fm Page 4 Monday, January 19, 2009 6:51 PM

Registering a handset to the base unit

1 Handset:

Lift the handset and press {OFF}.

2 Base unit:

Press and hold {LOCATOR} for about 5 seconds until the registration
tone sounds.
LIf all registered handsets start ringing, press the same button to

stop. Then repeat from step 1.

LThe next step must be completed within 90 seconds.

3 Handset:

Place the handset on the charger.
LContinue the operation even when the handset display shows

“Registering”.

4 With the handset still on the charger, wait until a long beep sounds

and w stops flashing.

Note:

LIf an error tone sounds, or if w is still flashing, register the handset

according to the base unit’s operating instructions.

Display language

1 {MENU} i {#}{1}{1}{0}
2 {V}/{^}: Select the desired setting.
3 Press the middle soft key to save. i {OFF}

4 For assistance, please visit http://www.panasonic.com/help

TGA106(e).fm Page 5 Monday, January 19, 2009 6:51 PM

Belt clip

NTo attach NTo r e mov e

Wall mounting

1 Drive the screws (not supplied) into the wall.
2 Mount the charger (A), then slide it down (B) and to the right (C)

until it is secure.

25.4 mm
(1 inch)

Screws

(120 V AC, 60 Hz)

For assistance, please visit http://www.panasonic.com/help 5

A

B

C

TGA106(e).fm Page 6 Monday, January 19, 2009 6:51 PM

For your safety

To prevent severe injury and loss of life/property, read this section carefully before
using the product to ensure proper and safe operation of your product.

WARNING

Power connection

L Completely insert the AC adaptor/power plug into the power outlet. Failure to do

so may cause electric shock and/or excessive heat resulting in a fire.

L Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it

from the power outlet, then wiping with a dry cloth. Accumulated dust may cause
an insulation defect from moisture, etc. resulting in a fire.

L Unplug the product from power outlets if it emits smoke, an abnormal smell, or

makes an unusual noise. These conditions can cause fire or electric shock.
Confirm that smoke has stopped emitting and contact the Panasonic Call Center
at 1-800-211- PANA (1-800-211-7262).

Installation

L To prevent the risk of fire or electrical shock, do not expose the product to rain or

any type of moisture.

L Do not place or use this product near automatically controlled devices such as

automatic doors and fire alarms. Radio waves emitted from this product may
cause such devices to malfunction resulting in an accident.

CAUTION

Installation and relocation

L The AC adaptor is used as the main disconnect device. Ensure that the AC outlet

is installed near the product and is easily accessible.

Battery

L We recommend using the supplied batteries or additional/replacement batteries

noted on page 2 for replacement battery information. USE ONLY rechargeable
Ni-MH batteries AAA (R03) size.

L Do not mix old and new batteries.
L Do not open or mutilate the batteries. Released electrolyte from the batteries is

corrosive and may cause burns or injury to the eyes or skin. The electrolyte is
toxic and may be harmful if swallowed.

L Exercise care when handling the batteries. Do not allow conductive materials

such as rings, bracelets, or keys to touch the batteries, otherwise a short circuit

6 For assistance, please visit http://www.panasonic.com/help

TGA106(e).fm Page 7 Monday, January 19, 2009 6:51 PM

may cause the batteries and/or the conductive material to overheat and cause
burns.

L Charge the batteries provided with or identified for use with this product only, in

accordance with the instructions and limitations specified in this manual.

L Only use a compatible charger to charge the batteries. Do not tamper with the

charger. Failure to follow these instructions may cause the batteries to swell or
explode.

Attention:

A nickel metal hydride battery that is
recyclable powers the product you have
purchased.
Please call 1-800-8-BATTERY (1-800-822-

8837) for information on how to recycle this
battery.

Other information

L Operating the product near electrical appliances may cause interference. Move

away from the electrical appliances.

L Use only the power cord and batteries indicated in this manual. Do not dispose

of batteries in a fire. They may explode. Check with local codes for possible
special disposal instructions.

Routine care

L Wipe the outer surface of the product with a soft moist cloth.
L Do not use benzine, thinner, or any abrasive powder.

Notice for product disposal, transfer, or return

L This product can store your private/confidential information. To protect your

privacy/confidentiality, we recommend that you erase information such as
phonebook or caller list entries from the memory before you dispose of, transfer,
or return the product.

FCC and other information

This equipment is hearing aid compatible as defined by the FCC in 47 CFR Section

68.316.

When you hold the phone to your ear, noise might be heard in your Hearing Aid.
Some Hearing Aids are not adequately shielded from external RF (radio frequency)
energy. If noise occurs, use an optional headset accessory or the speakerphone

For assistance, please visit http://www.panasonic.com/help 7

TGA106(e).fm Page 8 Monday, January 19, 2009 6:51 PM

option (if applicable) when using this phone. Consult with your audiologist or
Hearing Aid manufacturer about the availability of Hearing Aids which provide
adequate shielding to RF energy commonly emitted by digital devices.

WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST
CALLS TO EMERGENCY NUMBERS:

1) Remain on the line and briefly explain to the dispatcher the reason for the call.

2) Perform such activities in the off-peak hours, such as early morning or late
evenings.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
Privacy of communications may not be ensured when using this phone.

CAUTION:

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

FCC RF Exposure Warning:

L This product complies with FCC radiation exposure limits set forth for an

uncontrolled environment.

L This handset may not be collocated or operated in conjunction with any other

antenna or transmitter.

8 For assistance, please visit http://www.panasonic.com/help

TGA106(e).fm Page 9 Monday, January 19, 2009 6:51 PM

L The handset may be carried and operated with only the specific provided belt-

clip. Other non-tested belt-clips or similar body-worn accessories may not
comply and must be avoided.

Notice:

L FCC ID can be found inside the battery compartment or on the bottom of the unit.

Compliance with TIA-1083 standard:

Compatible with

Hearing Aid T-Coil

Telephone handsets identified with this logo have reduced
noise and interference when used with T-Coil equipped hearing
aids and cochlear implants.

T

TIA-1083

Notice

LThis product is designed for use in the United States of America. Sale or use

of this product in other countries may violate local laws.

LCet appareil est conçu pour être utilisé aux États-Unis d’Amérique. La vente

ou l’emploi de cet appareil dans certains autres pays peut constituer une
infraction à la législation locale.

LEste producto está diseñado para usarse en los Estados Unidos de América.

La venta o el empleo de este producto en ciertos países puede constituir
violación de la legislación local.

Lҏ౰ࠢட࣏୽ٺҢՄ೩Ȅӵڏт୽ড়᎛୵ܖٺҢȂџ૖ོႂІ࿋ӴݲٽȄ

Lߎߩ⵾ຠߪޔᣣᧄ࿖ᄖߢߩ૶↪ࠍ⋡⊛ߣߒߡ⸳⸘ߐࠇߡ߅ࠅޔᣣᧄ࿖ౝߢߩ

૶↪ߪᴺᓞ㆑෻ߣߥࠅ߹ߔޕᓥߞߡޔᒰ␠ߢߪᣣᧄ࿖ౝߦ߅޿ߡߪේೣߣߒ

ߡୃℂߥߤߩࠨ࡯ࡆࠬߪ⥌ߒ߆ߨ߹ߔޕ

For assistance, please visit http://www.panasonic.com/help 9

TGA106(e).fm Page 10 Monday, January 19, 2009 6:51 PM

IMPORTANT!

If your product is not working properly. . .

1. Read this Installation Manual

2. Visit our website: http://www.panasonic.com/help

L

FAQs and troubleshooting hints are available.

3. Contact us via the web at:
http://www.panasonic.com/contactinfo

4. Call us at: 1-800-211-PANA (1-800-211-7262)

L Monday - Friday 9:00am - 9:00pm (EST),

Saturday/Sunday 10:00am

To order replacement batteries, call 1-800-332-5368 or
visit http://www.panasonic.com/batterystore

- 7:00pm (EST)

One Panasonic Way, Secaucus, New Jersey 07094

Copyright:

This material is copyrighted by Panasonic Communications Co., Ltd.,
and may be reproduced for internal use only. All other reproduction, in
whole or in part, is prohibited without the written consent of Panasonic
Communications Co., Ltd.
© Panasonic Communications Co., Ltd. 2009

10 For assistance, please visit http://www.panasonic.com/help

TGA106(sp-sp).fm Page 1 Monday, January 19, 2009 6:56 PM

Manual de instalación

Auricular Inalámbrico Digital Adicional

Modelo N°

Gracias por adquirir un producto Panasonic.

Esta unidad es un auricular adicional compatible con la siguiente
serie de teléfono inalámbrico digital Panasonic: KX-TG1061
Debe registrar este auricular en su unidad base antes de poder
usarlo. Este manual de instalación sólo describe los pasos
necesarios para registrar y comenzar a usar el auricular. Lea las
instrucciones de operación de la unidad base para obtener más
detalles.

KX-TGA106

Cargue las baterías aproximadamente durante 7 horas antes de
usarse por primera vez.

Lea este manual de instalación antes de usar la unidad y guárdelo para
consultarlo en el futuro.

Visite nuestro sitio web para obtener ayuda:

http://www.panasonic.com/help

Rico (sólo en inglés).

para clientes de EE. UU. o Puerto

TGA106(sp-sp).fm Page 2 Monday, January 19, 2009 6:56 PM

Información de los accesorios

Accesorios que se suministran

Accesorio/Número de pedido Cantidad

Cargador/PNWETGA106M 1
Adaptador de corriente/PQLV219Z 1
Baterías recargables/HHR-4DPA

(Pieza N° HHR-55AAABU o N4DHYYY00004)

*1

Cubierta del auricular
Sujetador para cinturón/PNKE1029Z1 1

*1 La cubierta del auricular viene unida a él.

Nota:

L

Lea las instrucciones de operación de la unidad base para obtener
información sobre accesorios adicionales o de repuesto.

/PNYNTGA641TR 1

2

Instalación

Conexións

Ganchos

(120 V CA, 60 Hz)

Nota:

L

Use sólo el adaptador de corriente Panasonic PQLV219 que se suministra.

L

El adaptador de corriente debe permanecer conectado todo el tiempo. (Es
normal que el adaptador se caliente durante su uso.)

(2)

TGA106(sp-sp).fm Page 3 Monday, January 19, 2009 6:56 PM

Instalación y carga de las baterías

Importante:

L

Utilice las baterías recargables que se suministran. Para reemplazarlas,
recomendamos el uso de las baterías recargables Panasonic que se
especifican en la página 2.

L

Limpie los extremos de las baterías (S, T) con un paño seco.

L

Evite tocar los extremos de las baterías (S, T) o los contactos de la unidad.

L

Confirme que las polaridades estén correctas (S, T).

L

UTILICE SÓLO baterías de Ni-MH tamaño AAA (R03).

L

NO utilice baterías Alcalinas, de Manganeso o de Ni-Cd.

Cargue aproximadamente durante 7 horas.

L

Cuando las baterías estén completamente cargadas, el indicador de carga se
apagará.

Confirme que aparezca

SÓLO baterías
Ni-MH recargables

“Cargando”.

Nota:

L

Si las baterías están completamente cargadas pero el tiempo de
funcionamiento parece ser más corto, limpie los extremos de las baterías
(

S, T

) y los contactos de carga con un paño seco y cárguelas de nuevo.

(3)

TGA106(sp-sp).fm Page 4 Monday, January 19, 2009 6:56 PM

Cómo registrar un auricular a la unidad base

1

Auricular:

Levante el auricular y oprima {OFF}.

2

Unidad base:

Oprima y mantenga oprimido {LOCATOR} durante aproximadamente
5 segundos hasta que suene el tono de registro.

L

Si todos los auriculares registrados comienzan a timbrar, oprima el mismo
botón para detenerlos. Después repita desde el paso 1.

L

El siguiente paso debe completarse en un máximo de 90 segundos.

3

Auricular:

Coloque el auricular en el cargador.

L

Continúe la operación aunque la pantalla del auricular muestre

“

Registrando”.

4

Con el auricular aún en el cargador, espere a que se emita un pitido largo y

w

deje de parpadear.

Nota:

L

Si suena un tono de error, o si w continúa parpadeando, registre el auricular
de acuerdo con las instrucciones de operación de la unidad base.

Idioma de la pantalla

1

{

MENU} i

2

{V}/{^}

3

Oprima la tecla de función del medio para guardar. i {OFF

{#}{1}{1}{0}

: Seleccione la configuración deseada.

}

(4)

TGA106(sp-sp).fm Page 5 Monday, January 19, 2009 6:56 PM

Sujetador para cinturón

N

Para colocarlo

N

Para retirarlo

Montaje en la pared

1

Coloque los tornillos (no se suministran) en la pared.

2

Monte el cargador (A), y después deslícelo hacia abajo (B) y hacia la
derecha (

C

) hasta que quede seguro.

25.4 mm

(1 pulgada)

Tornillos

(120 V CA, 60 Hz)

A

B

C

(5)

TGA106(sp-sp).fm Page 6 Monday, January 19, 2009 6:56 PM

Notas

(6)