Panasonic KX-TG8220E, KX-TG8200E, KX-TG8222E, KX-TG8202E User Manual

TG8200_8220E(e)_QG.fm Page 1 Wednesday, May 30, 2007 6:41 PM

Digital Cordless Phone

Model No. KX-TG8200E/KX-TG8202E

Digital Cordless Answering System

Model No. KX-TG8220E/KX-TG8222E

Quick Guide

Routine care
LTo clean the product, use a dry soft cloth. The outer surface of the product can

be scratched by wiping or rubbing with a hard cloth.

Connections

Base unit

“Click”

To telephone line

USE ONLY the supplied cord.

Important:

LIf you use a telephone line cord which is not supplied, the unit may not work

properly.

Charger

(KX-TG8202/KX-TG8222)

To AC mains outlet
(220–240 V, 50 Hz)

Press plug firmly.

Hooks
To AC mains outlet
(220–240 V, 50 Hz)

USE ONLY the supplied AC adaptor.

Press plug firmly.

Hooks

USE ONLY the supplied AC adaptor (Smaller).

PQQW15778ZA DC0607PW0

TG8200_8220E(e)_QG.fm Page 2 Wednesday, May 30, 2007 6:41 PM

Battery installation/Battery charge

Initial charge: 7 hours

Base unit

Rechargeable
Ni-MH ONLY

*1 The pictured model is KX-TG8200.
*2 KX-TG8202/KX-TG8222

Note:

LUSE ONLY rechargeable Ni-MH batteries.
LDo NOT use Alkaline/Manganese/Ni-Cd batteries.

Screen saver mode

The backlight will turn off completely after 1 minute
of inactivity if the handset is not on the base unit or

charger.
Press {ih} to turn the display on again.

*1

“Charging” will
be displayed.

Charger

*2

– 2 –

{ih}

TG8200_8220E(e)_QG.fm Page 3 Wednesday, May 30, 2007 6:41 PM

Operating tips

Using the joystick

Push the joystick up, down, left, or right to
navigate through menus and to select.

Note:

LWhen selecting menu or the desired item,

these operating instructions use the
following indication.
Example: {^}/{V}: “Off”
Push the joystick up or down to select the
words in quotations.

Adjusting the receiver or speaker
volume

Push the joystick up or down while on a call.

Volume down

Soft keys

The handset features 2 soft keys and a
joystick. By pressing a soft key, or by
pressing the centre of the joystick, you can
select the feature shown directly above it on
the display.

Volume up

Menu icons

When in standby mode, pressing down on the centre of the joystick reveals the
handset’s main menu. From here you can access various features and settings.

j Caller List

X SMS (Short Message Service)

K Time Settings

I Answer System

*1 KX-TG8200/KX-TG8202
*2 KX-TG8220/KX-TG8222

*1

*2

– 3 –

N Handset Setup

| Base Unit Setup

M Display Setup

TG8200_8220E(e)_QG.fm Page 4 Wednesday, May 30, 2007 6:41 PM

Date and time

1 " (centre of joystick)
2 Select N by pushing the joystick in any direction. i #
3 Push the joystick up or down to select “Time Settings”. i #
4 Push the joystick up or down to select “Set Date & Time”. i #
5 Enter the current date, month, and year.
6 Enter the current hour and minute.
7 # i {ih}

Basic operations

C Making/Answering calls (Handset)

Making calls Dial the phone number. i {C}/{s}

Answering calls {C}/{s}

Hanging up {ih}

Receiver/speaker volume Push the joystick up or down while on a call.

Making a call using the redial
list

Handset ringer volume 1 " (centre of joystick) i N i #

k Phonebook (Handset)

Adding entries (names and
phone numbers)

Making calls 1 n (left soft key)

I Answering system (Base unit): KX-TG8220/KX-TG8222

Answering on/off Press {s} to turn on/off the answering system.

Listening to messages {6}

j (right soft key) i {^}/{V}: Select the desired
number. i {C}/{s}

2 {^}/{V}: “Ringer Setup” i #
3 {^}/{V}: “Ringer Volume” i #
4 {^}/{V}: Select the desired volume. i # i

{ih}

1 n (left soft key) i "
2 {^}/{V}: “New Entry” i #
3 Enter the party’s name (16 characters max.). i

#

4 Enter the party’s phone number (24 digits max.).

i #

5 {^}/{V}: Select the desired category. i #
6 {^}/{V}: “Save” i # i {ih}

LTo enter a name, see the character table in the

operating instructions.

2 {^}/{V}: Select the desired entry. i {C}

– 4 –

TG8200_8220E(e)_QG.fm Page 5 Wednesday, May 30, 2007 6:41 PM

Frequently asked questions

Question Cause & solution

Why is w flashing? LThe handset is too far from the base unit. Move

Why is the handset display
blank?

What should I do when the
handset does not turn on?

How long is the battery
operating time?

Can I keep the handset on
the base unit or charger
when I am not using it?

When should I replace the
batteries?

What is a PIN? LThe PIN is a 4-digit number that must be entered

closer.

LThe base unit AC adaptor is not connected.

Check the connections.

LYou are using the handset or base unit in an area

with high electrical interference. Place the
handset and base unit away from interference
sources, such as antennas and mobile phones.

LThe handset is not registered to the base unit.

Register it (page 7).

LThe handset is in screen saver mode. Press

{ih} to activate the handset display again.

LMake sure that the batteries are installed

correctly.

LFully charge the batteries.
LClean the charge contacts and charge again.

LWhen you are using fully-charged Ni-MH batteries

(supplied batteries);
In continuous use: 12 hours max.
In continuous standby mode: 150 hours max.

LIt is normal for batteries not to reach full capacity

at the initial charge. Maximum battery
performance is reached after a few complete
cycles of charge/discharge (use).

LActual battery performance depends on a

combination of how often the handset is in use
and how often it is not in use (standby).

LEven after the handset is fully charged, the

handset can be left on the base unit or charger
without any ill effect on the batteries.

LIf the batteries are fully charged until & is

displayed, but
replace the batteries with new ones.

in order to change certain base unit settings. The
default PIN is “0000”.

)

is displayed after a few calls,

– 5 –

TG8200_8220E(e)_QG.fm Page 6 Wednesday, May 30, 2007 6:41 PM

Frequently asked questions

Question Cause & solution

What do I need to do to
display caller information?

What should I do when:
– I hear static or sound cuts

in and out?

– there is interference from

other electrical units?

What should I do when the
operating time seems to be
short even after I fully
charged the batteries?

What do I need to do to
erase W (Missed call) from
the display?

LYou need to subscribe to Caller ID service.

Consult your service provider/telephone company
for details.

LThe message “You must first subscribe

to Caller ID.” will be displayed until you

receive caller information after subscribing to
Caller ID service.

LPlace the handset and the base unit away from

other electrical appliances.

LMove closer to the base unit.
LYour unit is connected to a telephone line with

DSL service. We recommend connecting a filter
(contact your DSL service provider) to the
telephone line between the base unit and the
telephone line jack.

LWipe the battery ends (S, T) and the unit

contacts with a dry cloth.

LThere are unviewed missed calls remaining. View

them using the following method.

1 " (centre of joystick) i j i #
2 Push the joystick down to search from the most

recent call, or push the joystick up to search
from the oldest call.

– 6 –

TG8200_8220E(e)_QG.fm Page 7 Wednesday, May 30, 2007 6:41 PM

Registering a handset to a base unit

The supplied handset and base unit are pre-registered. When you purchase an
additional handset, refer to the additional handset’s installation manual for
registration. If for some reason the handset is not registered to the base unit, register
the handset.

1 " (centre of joystick) i N i #
2 {^}/{V}: “Registration” i #
3 {^}/{V}: “Register H.set” i #
4 {^}/{V}: Select a base unit number. i #

5 Proceed with the operation for your model.

NKX-TG8200/KX-TG8202

Press and hold {x} on the base unit for
about 5 seconds. (No registration tone)

NKX-TG8220/KX-TG8222

Press and hold {x} on the base unit for
about 5 seconds, until the registration tone
sounds.

#

{x}

6 Wait until “Enter Base PIN” is displayed.

i Enter the base unit PIN (default: “0000”).
i #

– 7 –

{x}

#

TG8200_8220E(e)_QG.fm Page 8 Wednesday, May 30, 2007 6:41 PM

Optional service (Caller ID and SMS)

If you subscribe to Caller ID service, you can:

012345

– display caller information

– identify who is calling by using different display colours and

012345

ringtones (handset phonebook category)

To use SMS, you must subscribe to Caller ID and/or appropriate service.

– SMS (Short Message Service)

Sales and support information

Customer Care Centre

L For customers within the UK: 0844 844 3898
L For customers within the Republic of Ireland: 01289 8333
L Visit our website for product information: www.panasonic.co.uk
L E-mail: [e-mail]

Direct Sales at Panasonic UK

L Order accessory and consumable items for your product with ease and

confidence by phoning our Customer Care Centre Monday - Thursday 9:00am ­5:30pm, Friday 9:30am - 5:30pm (Excluding public holidays).

L Or go on line through our Internet Accessory ordering application at

www.panasonic.co.uk

L Most major credit and debit cards accepted.
L All enquiries transactions and distribution facilities are provided directly by

Panasonic UK Ltd.

L It couldn’t be simpler!
L Also available through our Internet is direct shopping for a wide range of finished

products, take a browse on our website for further details.

Customer Care Helpline Tel. No.: U.K. 0844 844 3898 / R.O.I. 01289 8333

– 8 –

TG8200_8220E(e)_QG.fm Page 9 Wednesday, May 30, 2007 6:41 PM

– 9 –

TG8200_8220E(e)_QG.fm Page 10 Wednesday, May 30, 2007 6:41 PM

IMPORTANT

0844 844 3898 (UK)

01289 8333 (Repl of Ireland)

If you have problems setting up

or operating this product please

call the Panasonic DECT Helpline