Panasonic KX-TG8070E User Manual

TG8070_TG8090E(e)_QG.fm Page 1 Wednesday, May 30, 2007 11:23 AM

Digital Cordless Phone

Model No. KX-TG8070E

Digital Cordless Answering System

Model No. KX-TG8090E/KX-TG8092E

KX-TG8093E

Quick Guide

Connections

Base unit (KX-TG8070) Base unit (KX-TG8090/KX-TG8092/

KX-TG8093)

Hook

To telephone
network

To AC mains outlet
(220–240 V, 50 Hz)

Use only the supplied AC adaptor
and telephone line cord. Insert the
AC adaptor plug until a short beep
sounds.

Charger (KX-TG8092/KX-TG8093)

25 mm

Screws

Hook

To AC mains outlet
(220–240 V, 50 Hz)

To telephone network

Use only the supplied AC adaptor
and telephone line cord. Insert the
AC adaptor plug until a short beep
sounds.

To AC mains outlet
(220–240 V, 50 Hz)

PQQW15624YA DC0407DM1057

TG8070_TG8090E(e)_QG.fm Page 2 Wednesday, May 30, 2007 11:23 AM

Battery installation/Battery charge

Initial charge: 8 hours

*1

Rechargeable
Ni-MH ONLY

Note:

LUSE ONLY rechargeable Ni-MH batteries.
LDo NOT use Alkaline/Manganese/Ni-Cd batteries.

Base unit

*1 The pictured model is KX-TG8070.
*2 KX-TG8092/KX-TG8093

Charger

Screen saver mode

If the handset is not on the base unit or charger

The backlight will turn off completely after 1 minute of inactivity, even when:

– on a call
– operating the answering system
To use the handset when it is in screen saver mode, activate the handset display again by:
–pressing {^} or {V} when on a call or operating the answering system
–pressing {i} for all other times

While charging

The backlight will be dimmed after 1 minute of inactivity. The backlight can be turned off

completely depending on the setting. To use the handset when it is in screen saver mode, lift the
handset to activate the handset display again.

*2

– 2 –

TG8070_TG8090E(e)_QG.fm Page 3 Wednesday, May 30, 2007 11:23 AM

Operating tips

Using the navigator key

Press {^}, {V}, {<}, or {>} to navigate through
menus and to select items shown on the display.

Adjusting the receiver or speaker volume

Press {^} or {V} while on a call.

Menu icons

When in standby mode, pressing the right soft key reveals the handset’s main menu. From here you
can access various features and settings.

{^}

{<}{>}

{V}

h SMS (Short Message Service)

x Caller List

q Display Setup
r Handset Setup

*1 KX-TG8090/KX-TG8092/KX-TG8093
*2 KX-TG8070

h Base Unit Setup

s Answer System

( Ringer Setup

Soft keys

The handset features 2 soft keys. By pressing a soft
key, you can select the feature or operation
indicated by the soft key icon shown directly above
it.

Dialling mode (tone/pulse)

1 {MENU} (right soft key)
2 Select h by pressing {^}, {V}, {<}, or {>}. i {OK}
3 Enter the base unit PIN (default: “0000”). i {OK}
4 Press {^} or {V} to select “Call Options”. i {OK}
5 Press {^} or {V} to select “Dial Mode”. i {OK}
6 Press {^} or {V} to select the desired setting. i {OK} i {i}

*1

*2

INT MENU

Date and time

1 {MENU} (right soft key)
2 Select r by pressing {^}, {V}, {<}, or {>}. i {OK}
3 Press {^} or {V} to select “Set Date & Time”. i {OK}
4 Enter the current date, month, and year. i {OK}
5 Enter the current hour and minute.
6 {OK} i {i}

– 3 –

TG8070_TG8090E(e)_QG.fm Page 4 Wednesday, May 30, 2007 11:23 AM

Basic operations

C Making/Answering calls (Handset)

Making calls Dial the phone number. i {C}/{s}

Answering calls {C}/{s}

Hanging up {i}

Receiver/speaker volume Press {^} or {V} while on a call.

Making a call using the redial list {V/R} i {^}/{V}: Select the desired number. i {C}
Handset ringer volume 1 {MENU} (right soft key) i r i {OK}

2 {^}/{V}: “Ringer Setup” i {OK}
3 {^}/{V}: “Ringer Volume” i {OK}
4 {^}/{V}: Select the desired volume. i {OK} i {i}

k Phonebook (Handset)

Adding entries (names and phone
numbers)

Making calls 1 {k}

s Answering system (Handset): KX-TG8090/KX-TG8092/KX-TG8093

Answering on/off 1 {MENU} (right soft key) i s i {OK}

Listening to messages 1 {MENU} (right soft key) i s i {OK}

1 {k} i {MENU}
2 {^}/{V}: “New Entry” i {OK}
3 Enter the party’s name (15 characters max.). i {OK}
4 Enter the party’s phone number (24 digits max.). i

{OK} i {i}
LTo enter a name, see the character table in the

operating instructions.

2 {^}/{V}: Select the desired entry. i {C}

2 {^}/{V}: “Answer On/Off” i {OK}
3 {^}/{V}: “Answer On” or “Answer Off” i {OK} i

{i}

2 {^}/{V}: “Play All Msg.” i {OK}

LThe handset plays back all messages, new messages

first.

– 4 –

TG8070_TG8090E(e)_QG.fm Page 5 Wednesday, May 30, 2007 11:23 AM

Frequently asked questions

Question Cause & solution

Why is w flashing and
“Register!” is shown on the
handset display?

Why is w flashing and
“Searching...” is shown on the
handset display?

Why is the handset display blank? LThe handset is in screen saver mode. If charging, lift the

Why can I not make calls? LThe dialling mode setting is incorrect. Set to “Tone” or

What should I do when the handset
does not turn on?

How long is the battery operating
time?

Can I keep the handset on the base
unit or charger when I am not using
it?

When should I replace the batteries? LIf the batteries are fully charged until @ is displayed, but /

LThe handset is cancelled. If you want to register the

handset to the base unit(s), follow “Registering a handset
to a base unit”, page 6. If you want to use a base unit(s)
which was registered to the handset before cancellation,
select it by following “Selecting a base unit” in the
operating instructions.

LThe handset is too far from the base unit. Move closer.
LThe base unit AC adaptor is not connected. Check the

connections.

LYou may have selected the wrong base unit. Select the

right base unit.

LYou are using the handset or base unit in an area with high

electrical interference. Place the handset and base unit
away from interference sources, such as antennas and
mobile phones.

handset to activate the handset display again. If the
handset is not on the base unit or charger, activate the
handset display again by:
– pressing {^} or {V} when on a call or operating the

answering system

– pressing {i} for all other times

L“Dimmed Backlight” is set to “Off”. Change the

setting.

“Pulse” as needed.

LMake sure that the batteries are installed correctly.
LFully charge the batteries.
LClean the charge contacts and charge again.

LWhen you are using fully-charged Ni-MH batteries

(supplied batteries);
In continuous use: 10 hours max.
In continuous standby mode: 100 hours max.

LIt is normal for batteries not to reach full capacity at the

initial charge. Maximum battery performance is reached
after a few complete cycles of charge/discharge (use).

LActual battery performance depends on a combination of

how often the handset is in use and how often it is not in
use (standby).

LEven after the handset is fully charged, the handset can be

left on the base unit or charger without any ill effect on the
batteries.

is displayed after a few calls, replace the batteries with
new ones.

– 5 –

TG8070_TG8090E(e)_QG.fm Page 6 Wednesday, May 30, 2007 11:23 AM

Frequently asked questions

Question Cause & solution

What is a PIN? LThe PIN is a 4-digit number that must be entered in order

to change certain base unit settings. The default PIN is
“0000”.

What do I need to do to display caller
information?

LYou need to subscribe to Caller ID service. Consult your

service provider/telephone company for details.

Registering a handset to a base unit

The supplied handset and base unit are pre-registered. If for some reason the handset is not
registered to the base unit, register the handset.

1 Press and hold {x} on the base unit for

about 5 seconds until a beep is heard.
LIf all registered handsets start ringing,

press {x} to stop, then repeat this step.

LAfter a beep is heard, the rest of this

procedure must be completed within 1
minute.

{x}

KX-TG8070

{x}

KX-TG8090/KX-TG8092/
KX-TG8093

2 {MENU} (right soft key) i r i {OK}
3 {^}/{V}: “Registration” i {OK}
4 {^}/{V}: “Register Handset” i {OK}
5 {^}/{V}: Select a base unit number. i

{OK}

6 “Enter PIN” is displayed. Enter the base

unit PIN (default: “0000”). i {OK}

{MENU}/{OK}

{OK}

– 6 –

TG8070_TG8090E(e)_QG.fm Page 7 Wednesday, May 30, 2007 11:23 AM

Optional services (Caller ID and SMS)

If you subscribe to Caller ID service, you can:

Tom
012345

– display caller information

To use SMS, you must subscribe to Caller ID and/or appropriate service.

SMS (Short Message Service)

Sales and support information

Customer Care Centre

L For customers within the UK: 0844 844 3898
L For customers within the Republic of Ireland: 01289 8333
L Visit our website for product information: www.panasonic.co.uk
L E-mail: [e-mail]

Direct Sales at Panasonic UK

L Order accessory and consumable items for your product with ease and confidence by phoning

our Customer Care Centre Monday - Thursday 9:00am - 5:30pm, Friday 9:30am - 5:30pm
(Excluding public holidays).

L Or go on line through our Internet Accessory ordering application at www.panasonic.co.uk
L Most major credit and debit cards accepted.
L All enquiries transactions and distribution facilities are provided directly by Panasonic UK Ltd.
L It couldn’t be simpler!
L Also available through our Internet is direct shopping for a wide range of finished products, take

a browse on our website for further details.

Customer Care Helpline Tel. No.: U.K. 0844 844 3898 / R.O.I. 01289 8333

– 7 –

TG8070_TG8090E(e)_QG.fm Page 8 Wednesday, May 30, 2007 11:23 AM

IMPORTANT

0844 844 3898 (UK)

the Panasonic DECT Helpline

If you have problems setting up or

operating this product please call

01289 8333 (Repl of Ireland)