Panasonic K10059 User Manual

SecurityPhone.book 1 ページ２００４年７月２１日　水曜日　午後６時５８分

SecurityLink® Plus

User’s Guide

K10059 6/04 Rev. A

SecurityPhone.book 2 ページ２００４年７月２１日　水曜日　午後６時５８分

This phone can be connected to an ADT Security System and used as an additional keypad interface. You can program/control system functions using the buttons on the telephone front panel.

The security system will provide the telephone line and power supply, and has priority over the telephone functions.

Overview

Communication with the Security System

The phone functions as a user interface (keypad/display) for the security system.

NArming and Disarming the Security System

You can arm/disarm the security system or set other system functions by using the function menu on the display.

NAlarms

When an alarm condition occurs, the base unit and cordless handset can sound an audible alarm with the status being displayed and announced, then the alarm report can be sent to the Customer Monitoring Center, if programmed so the alarm system is monitored, and upon receipt of an alarm signal by the Customer Monitoring Center.

NTwo Way Voice (SecurityLink

In case of emergency, an operator in a Customer Monitoring Center can monitor/ announce/talk using the speakerphone on base unit and cordless handset, if programmed.

PlusTM)

NRemote Phone Control

You can remotely control the security system by entering function commands from a touch tone phone located off the premises.

• ADT Monitoring Service must be in effect!

SecurityPhone.book 3 ページ２００４年７月２１日　水曜日　午後６時５８分

Contents

Location of Controls . . . . . . . . . 4

Security System Displays . . . . 5

Entry/Exit Delays . . . . . . . . . . . 6

Entry Delay . . . . . . . . . . . . . . . 6

Exit Delay . . . . . . . . . . . . . . . . 6

Exit Alarms . . . . . . . . . . . . . . . 6

Arming the System . . . . . . . . . . 7

Setting the Away mode . . . . . 8

Setting the Stay mode . . . . . . 9

Setting the Night-Stay

mode . . . . . . . . . . . . . . . . . 10

Setting the Instant mode . . . 11

Disarming the security

system . . . . . . . . . . . . . . . . . . 12

Bypassing Protection Zones . 14

Bypassing zones . . . . . . . . . 14

Quick Bypass . . . . . . . . . . . . 16

Chime Mode . . . . . . . . . . . . . . 17

Setting the Date and Time . . . 18

PANIC Keys . . . . . . . . . . . . . . . 20

Using the PANIC Keys . . . . . 20

Remote Phone Control . . . . . . 22

Selecting the Function

(Macro) . . . . . . . . . . . . . . . . . . 23

Device Commands . . . . . . . . . 24

Security Codes & Authority

Levels . . . . . . . . . . . . . . . . . . 25

Adding User Code . . . . . . . . 25

Deleting User Code . . . . . . . 27

Authority Level . . . . . . . . . . . 28

Access Group . . . . . . . . . . . . 30

RF User Number . . . . . . . . . 32

Pager . . . . . . . . . . . . . . . . . . 34

Schedules . . . . . . . . . . . . . . . . . 35

Viewing the Event Log . . . . . . 38

Testing the System . . . . . . . . . 39

Checking the Current Status . 40

Display Status . . . . . . . . . . . . 40

Voice Status . . . . . . . . . . . . . 41

Direct Commands . . . . . . . . . . 42

Mute Security . . . . . . . . . . . . . . 43

Two Way Voice Feature . . . . . 44

Listening Mode in Two Way

Voice . . . . . . . . . . . . . . . . . . 44

Talk Mode in Two Way

Voice . . . . . . . . . . . . . . . . . . 44

VOX Mode in Two Way

Voice . . . . . . . . . . . . . . . . . . 44

Function Menu Table . . . . . . . 45

If the Following Appear on Your

Display... . . . . . . . . . . . . . . . . 47

Troubleshooting . . . . . . . . . . . 48

Regulatory Statements and

Warnings. . . . . . . . . . . . . . . . . 48

LIMITATIONS OF THIS

SYSTEM . . . . . . . . . . . . . . . . . 51

PANASONIC PRODUCT

LIMITED WARRANTY. . . . . . . 52

Important:

Throughout these Operating Instructions, and are used to indicate with which unit an operation can be performed.

Handset Base Unit

: Perform with the handset.

: Perform with the base unit.

Handset Base Unit

SAVE

SecurityPhone.book 4 ページ２００４年７月２１日　水曜日　午後６時５８分

Location of Controls

Base Unit

Display

[ADT]

Press to enter the function menu for the security system.

PANIC keys Press and hold for two seconds in

event of emergency (panic).

[STOP]

Press to exit programming or terminate the function menu.

[FUNCTION/EDIT]

Press to enter the function menu for the telephone and Answering systems.

Navigator Key

[ERASE]

Press to erase the entered code or number.

Press the arrow to scroll through menu or select items.

Cordless Handset

Soft Key Press to enter the function menu for the

security system.

Soft Key Press and hold in event of emergency (panic).

[CONF (Conference)/ FUNCTION]

Press to enter the function menu for the telephone and answering systems.

ADT

PANIC

Display

Navigator Key Press the arrow to scroll through menu or select items.

[OFF]

Press to exit programming or terminate the function menu.

[HOLD/CLEAR]

Press to erase the entered code or number.

SecurityPhone.book 5 ページ２００４年７月２１日　水曜日　午後６時５８分

Security System Displays

Base unit Cordless handset

12:00AM DEC.31

Received calls

READY

IN USE

MESSAGE

READY

IN USE

Received calls

ADT

PANIC PLAY

[1]

1 The base unit and cordless handset display status icons below:

Icon Meaning

READY

ARMED

NOT RDY

2 While the phone is in the menu mode, the display

shows real time status, or the display shows the screen to enter a number or set the date and time.

ADT

3 “ ” is used to enter the function menu for the security system. To operate

ADT

“ ”, press the left soft key.

The phone is ready to arm the security system.

The security system is armed.

The phone is not ready to arm the security system. The protected doors/windows may be open (faulted). Close them, or try bypassing the faulted zone if you want the zone to remain unprotected.

Example

Enter Sched No. 00=Quit

PANIC PANIC

4 “ ” is used in event of emergency (panic). To operate “ ”, press the

middle soft key, then press the appropriate emergency key (see page 20).

• ADT Monitoring Service must be in effect!

SecurityPhone.book 6 ページ２００４年７月２１日　水曜日　午後６時５８分

Entry/Exit Delays

Entry Delay

You can have time to re-enter your house from pre-selected door by programming entry delay times. You must disarm the system before entry delay time expires. The phone beeps until you disarm the system. Confirm with your installer for your delay time.

Exit Delay

You can have time to go out through the exit door without cancelling an alarm. The exit delay time starts immediately after you arm the system. The phone displays “You may exit now”. After the message disappears, the system completes arming and the phone alarms. If programmed, the phone beeps slowly after arming the system, then beeps fast to alert you of the exit delay time end. If you do not exit your house, you should disarm the system to stop an alarm and rearm the system. Confirm with your installer for your programmed exit delay time.

Exit Alarms

The exit delay starts after you arm the system. If the exit/entry door or interior zone is faulted after the exit delay time expires, the phone alarms and the entry delay starts. When you disarm the system before the entry delay time expires, an alarm stops and the “Alarm Cancelled” and the faulted zone number are displayed. The message is not sent to the Customer Monitoring Center. Then you can close the displayed open zone and clear the message by entering your security code. If the system is not disarmed, or the exit/entry door or interior zone is open before the entry delay ends, the phone alarms and the exit alarm message and faulted zone are displayed. The exit alarm message is sent to the Customer Monitoring Center. You should disarm the system to stop an alarm, and enter your security code and [1] on the keypad to clear the display.

SecurityPhone.book 7 ページ２００４年７月２１日　水曜日　午後６時５８分

Arming the System

You can set the security mode through the function menu using the base unit or handset. There are 4 modes, AWAY, STAY, Night-Stay and INSTANT.

If you want to change the security mode after you arm the system, disarm the system, then set your required mode through the function menu.

Before arming the system, refer to the section “Entry/Exit Delays” on pages 12 to 13 and “Arming the System” on page 15 in the 3000EN Security Systems User’s Guide.

Make sure all perimeter doors and windows are closed and is displayed.

• If protected windows and doors are opened when the system is armed: — the phone alarms and a conversation or a call is disconnected, or an incoming

call is disconnected after you press [TALK] or the speakerphones to answer.

READY

SecurityPhone.book 8 ページ２００４年７月２１日　水曜日　午後６時５８分

Arming the System

Setting the Away mode

When nobody (including pets) remains at home, select this mode. When you set the Away mode,

— the entire system (interior and perimeter) is armed, and — exit delay begins so that you can leave through the entry/exit door.

Base Unit

1 Press [ADT].

2 Press [

3 Scroll to “AWAY” by pressing [

4 Press [

door during the exit delay time.*

• The armed AWAY message is displayed.

Handset

the cordless handset.

The exit delay time depends on the system setting.

• To exit the menu, press [STOP] or [OFF].

To confirm the security mode you set, press [ADT] in the standby mode.

] at “ARM”.

] or [B].

], then go out through the entry/exit

: Press the soft key ( ), and follow steps 2 to 4 above, using

ADT

ARM

AWAY

SecurityPhone.book 9 ページ２００４年７月２１日　水曜日　午後６時５８分

Arming the System

Setting the Stay mode

When you want to arm the system while persons stay inside, select this mode.

When you set the Stay mode, — the perimeter zones, such as protected windows and doors, are armed — interior sensors are left disarmed — exit delay begins so that you can leave through the exit/entry door, and — if the protected perimeter windows and doors are opened, an alarm sounds

immediately.

Base Unit

1 Press [ADT].

2 Press [

3 Press [

• The armed STAY message is displayed.

] at “ARM”.

] at “STAY”.

ARM

STAY

Example

ARMED You may exit now

;;;

STAY

;;;

4 Press [STOP] to go to the standby mode.

Handset

the cordless handset. Press [OFF] to go to the standby mode.

• To exit the menu, press [STOP] or [OFF].

To confirm the security mode you set, press [ADT] in the standby mode.

: Press the soft key ( ), and follow steps 2 to 3 above, using

ADT

SecurityPhone.book 10 ページ２００４年７月２１日　水曜日　午後６時５８分

Arming the System

Setting the Night-Stay mode

When you want to get more increased security than the Stay mode, select this mode.

When you set the Night-Stay mode, — the perimeter zones and pre-selected interior sensors (programmed by your

installer) are armed, and

— if the protected perimeter windows and doors are opened or interior zones are

violated, an alarm sounds immediately.

Base Unit

1 Press [ADT].

2 Press [

3 Scroll to “Night-Stay” by pressing [

[

4 Enter your security code.

• If you entered the wrong security code, the phone

• The armed NIGHT-STAY message is displayed.

] at “ARM”.

] or

], then press [g].

will go back to the previous display. Try again from step 2.

ARM

Night-Stay

ENTER CODE

----

Example

;;;

NIGHT-STAY

You may exit now

;;;

5 Press [STOP] to go to the standby mode.

Handset

the cordless handset. Press [OFF] to go to the standby mode.

• To exit the menu, press [STOP] or [OFF].

To confirm the security mode you set, press [ADT] in the standby mode.

IMPORTANT:

When the Night-Stay mode is on, the selected interior zones are armed and cause an alarm if anyone enters those areas (e.g., waking in the middle of the night). To avoid sounding an alarm, you must disarm the system before any activity takes place in those interior zones

: Press the soft key ( ), and follow steps 2 to 4 above, using

ADT

SecurityPhone.book 11 ページ２００４年７月２１日　水曜日　午後６時５８分

Arming the System

Setting the Instant mode

When you stay at home and no one intends to use an entry/exit door, select this mode.

When you set the Instant mode, — the system is armed same as the Stay mode, and — if the protected perimeter windows and doors are opened, an alarm sounds

immediately.

Base Unit

1 Press [ADT].

2 Press [

3 Scroll to “INSTANT” by pressing [

then press [

• The armed INSTANT message is displayed.

] at “ARM”.

ARM

] or [B],

INSTANT

Example

ARMED ;INSTANT You may exit now

;

4 Press [STOP] to go to the standby mode.

Handset

using the cordless handset. Press [OFF] to go to the standby mode.

• To exit the menu, press [STOP] or [OFF].

To confirm the security mode you set, press [ADT] in the standby mode.

IMPORTANT:

Arming the system in this mode greatly increases the chance of false alarms. Use extreme care in selecting this mode of arming.

: Press the soft key ( ), and follow steps 2 and 3 above,

ADT

SecurityPhone.book 12 ページ２００４年７月２１日　水曜日　午後６時５８分

Disarming the security system

To disarm the security system through the function menu

You can disarm the system by turning the security mode off through the function menu.

Base Unit

1 Press [ADT].

2 Press [

3 Enter your security code.

• If you entered the wrong security code, the phone

] at “DISARM”.

will go back to the previous display. Try again from step 2.

DISARM

ENTER CODE

----

4 Press [STOP] to go to the standby mode.

Handset

the cordless handset. Press [OFF] to go to the standby mode.

: Press the soft key ( ), and follow steps 2 to 3 above, using

ADT

To disarm the security system using the security code and [1]

When the unit is in the standby mode:

1 Press [ADT].

2 Enter your security code, then press [1].

• The security system is disarmed.

3 Press [STOP] to go to the standby mode.

When slow or fast beeps sound while the system is armed:

1 Enter your security code.

• Beeps stop and the security system is disarmed.

SecurityPhone.book 13 ページ２００４年７月２１日　水曜日　午後６時５８分

Disarming the security system

When alarm sounds while the system is armed:

1 Enter your security code.

• The alarm stops, the security system is disarmed.

• Check the alarm display. If the protected doors or windows remain open, close them.

2 Press [ADT] to go to the standby mode.

3 Enter your security code, then press [1] to go to the ready status.

• A memory of alarm is cleared. ALARM SIGNAL IS NOT SENT TO THE CUSTOMER MONITORING CENTER.

READY

• “ ” is displayed.

SecurityPhone.book 14 ページ２００４年７月２１日　水曜日　午後６時５８分

Bypassing Protection Zones

Using this mode, you can set the selected zones to be unprotected. After setting this mode, set the security mode as desired.

While the security system is armed, you can not set the Bypass. To bypass zones, disarm the security system (p. 12).

• WHEN CERTAIN ZONES ARE BYPASSED, THE SYSTEM DOES NOT PROTECT THE BYPASSED ZONE, THE ALARM DOES NOT SOUND, AND AN ALARM SIGNAL IS NOT SENT TO THE CUSTOMER MONITORING CENTER.

• You can not set fire zones to be bypassed.

• When the system is disarmed, bypassed zones automatically is unbypassed.

Make sure all perimeter doors and windows are closed and is displayed.

READY

Bypassing zones

You can select the protection zones.

Refer to “Using the BYPASS key” on page 20 in the 3000EN Security Systems User’s Guide.

Base Unit

1 Press [ADT].

2 Scroll to “BYPASS” by pressing [

press [

3 Press [

] at “BYPASS(NORMAL)”.

4 Enter your security code.

5 Enter the desired zone number of 2 digits.

(Ex. To set zone 1 unprotected, enter “01”.)

• You can enter four zone numbers at one time. To enter over four zone numbers, repeat from the

step 3 after pressing [

] (ENTER).

] or [B], then

BYPASS

BYPASS(NORMAL)

ENTER CODE

----

ENTER ZONES

--,--,--,--,

Example

ENTER ZONES

--,--,--,01,

READY

=ENTER

SecurityPhone.book 15 ページ２００４年７月２１日　水曜日　午後６時５８分

Bypassing Protection Zones

6 Press [

• The “Bypass” message for bypassed zone number

• A confirmation tone (one beep) is heard for each

• If a confirmation tone (one beep) is not heard, you

] (ENTER).

is displayed momentarily.

bypassed zone.

entered the wrong security code in step 4 or wrong zone number in step 5, or the security mode is armed. The setting is not saved. Try again from step 3.

7 Press [STOP] to go to the standby mode.

Handset

: Press the soft key ( ), and follow steps 2 to 5 on the previous page, using the cordless handset. Press the soft key ( ), then press [OFF] to go to the standby mode.

ADT

SecurityPhone.book 16 ページ２００４年７月２１日　水曜日　午後６時５８分

Bypassing Protection Zones

Quick Bypass

If the Quick Bypass is programmed by the security system installer, you can set all faulted (open) zones unprotected at once. Confirm with your installer if the Quick Bypass is active for your system.

When Quick Bypass is used, all faulted (open) zones are unprotected, the alarm does not sound, and an alarm signal is not sent to the Customer Monitoring Center. Refer to “Quick Bypass” on page 21 in the 3000EN Security Systems User’s Guide.

Make sure all perimeter doors and windows are closed and is displayed.

READY

Base Unit

1 Press [ADT].

2 Scroll to “BYPASS” by pressing [

press [

3 Scroll to “QUICK BYPASS” by pressing [

[

], then press [g].

4 Enter your security code.

• If you entered the wrong security code, the phone will go back to the previous display. Try again from step 3.

• In a few seconds, all faulted (open) zones are displayed and automatically bypassed.

• The “Bypass” message is displayed momentarily.

] or [B], then

] or

BYPASS

QUICK BYPASS

ENTER CODE

----

5 Press [STOP] to go to the standby mode.

Handset

the cordless handset. Press [OFF] to go to the standby mode.

: Press the soft key ( ), and follow steps 2 to 4 above, using

ADT

SecurityPhone.book 17 ページ２００４年７月２１日　水曜日　午後６時５８分

Chime Mode

Even if the security system is not armed, the Chime mode can alert you by three beeps and announcement to the opening of a perimeter door or window.

Refer to “Chime Mode” on page 22 in the 3000EN Security Systems User’s Guide.

While the security system is armed, you can not turn the Chime on or off. To turn on, disarm the security system (p. 12).

Make sure all perimeter doors and windows are closed and is displayed.

Base Unit

1 Press [ADT].

READY

2 Scroll to “CHIME ON/OFF” by pressing [

[

], then press [g].

3 Enter your security code.

• If the Chime was turned on, the mode changes to off. If the Chime was turned off, the mode changes to on.

• If you entered the wrong security code, a confirmation tone (one beep) is not heard and the phone will go back to the previous display. The setting is not saved. Try again from step 2.

] or

CHIME ON/OFF

ENTER CODE

----

4 Press [STOP] to go to the standby mode.

Handset

: Press the soft key ( ), and follow steps 2 and 3 above,

using the cordless handset. Press [OFF] to go to the standby mode.

• If an opening of a protected door or window occurs when the Chime mode is on, the phone will stop the operation and go into the Chime mode. The following operations that will stop include: — programming the function menu — searching an item in the caller list, phone book or redial list — recording/playing back a greeting message — playing back messages — making an intercom — copying phone book — re-registering the cordless handset

• If an opening of a protected door or window occurs when the Chime mode is on, beeps sound and a conversation using a phone is disconnected temporarily.

• To confirm the Chime mode setting, press [ADT] in the standby mode. The “CHIME” message will be displayed when the security system is disarmed, and the Chime mode is turned on.

ADT

+ 39 hidden pages