Panasonic HDC-SD600P, HDC-SD600EB, HDC-SD600EC, HDC-SD600EF, HDC-SD600EG Service Manual
...
© Panasonic Corporation 2010 Unauthorized copying and distribution is a violation of law.
ORDER NO. VM1005029CE
B27
High Definition Video Camera
Model No. HDC-SD600P
HDC-SD600EB
HDC-SD600EC
HDC-SD600EE
HDC-SD600EF
HDC-SD600EG
HDC-SD600EP
HDC-SD600GN
Vol. 1
Colour
(K)...........Black Type
(H)...........Glay Type (only EB)
4
2
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions -----------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.)--------3
1.4. How to Discharge the Capacitor on Flash
P.C.B.----------------------------------------------------------4
2Warning--------------------------------------------------------------5
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------5
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------5
2.3. Caution for AC Cord (For EB)---------------------------6
2.4. How to Replace the Lithium Battery-------------------7
3 Service Navigation------------------------------------------------8
3.1. Introduction --------------------------------------------------8
3.2. General Description About Lead Free Solder
(PbF) ----------------------------------------------------------8
3.3. Important Notice 1:(Other than U.S.A. and
Canadian Market)------------------------------------------8
3.4. How to Define the Model Suffix (NTSC or PAL
model)---------------------------------------------------------9
3.5. Formatting--------------------------------------------------10
4 Specifications---------------------------------------------------- 11
5 Location of Controls and Components------------------14
6 Service Mode-----------------------------------------------------17
6.1. Lock Search History Indication -----------------------18
6.2. Power ON Self Check Result Display--------------- 18
7 Service Fixture & Tools---------------------------------------19
7.1. When Replacing the Main P.C.B. --------------------19
7.2. Service Position ------------------------------------------19
8 Disassembly and Assembly Instructions--------------- 20
8.1. Disassembly Flow Chart--------------------------------20
8.2. PCB Location----------------------------------------------20
8.3. Disassembly Procedure--------------------------------21
9 Measurements and Adjustments --------------------------38
9.1. Electric Adjustment --------------------------------------38
10 Factory Setting---------------------------------------------------40
10.1. How To Turn On The Factory Settings?------------ 40
10.2. What Is The Factory Settings? -----------------------41
3
1 Safety Precautions
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE
There are special components used in this equipment
which are important for safety. These part s are marked by
in the Schematic Diagrams, Circuit Board Layout,
Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
2. An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing.
3. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been overheated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2. Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading
should be between 1 MΩ and 5.2 MΩ. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
1.3. Leakage Current Hot Check
(See Figure 1.)
1. Plug the AC cord directly into the AC outlet. Do not use
an isolation transformer for this check.
2. Connect a 1.5 kΩ, 10 W resistor, in parallel with a 0.15 μF
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
Figure. 1
4
1.4. How to Discharge the Capacitor on Flash P.C.B.
CAUTION:
1. Be sure to discharge the capacitor on Flash P.C.B..
2. Be careful of the high voltage circuit on Flash P.C.B. when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and Remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1kΩ /5W).
(an equivalent type of resistor may be used.)
3. Put the resistor between both terminals of capacitor on Flash P.C.B. for ap prox. 5 seconds.
4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter.
Fig. F1
5
2Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help re duce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as al uminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
2.2. How to Recycle the Lithium Ion Battery (U.S. Only)
6
2.3. Caution for AC Cord
(For EB)
2.3.1. Information for Your Safety
IMPORTANT
Your attention is drawn to the fact that recording of prerecorded tapes or discs or other published or broadcast
material may infringe copyright laws.
WARNING
To reduce the risk of fire or sho ck hazard, do not expose
this equipment to rain or moisture.
CAUTION
To reduce the risk of fire or shock hazard and annoying
interference, use the recommended accessories only.
FOR YOUR SAFETY
DO NOT REMOVE THE OUTER COVER
To prevent electric shock, do not remove the cover. No user
serviceable parts inside. Refer servicing to qualified service
personnel.
2.3.2. Caution for AC Mains Lead
For your safety, please read the following text carefully.
This appliance is supplied with a moulded three-pin mains plug
for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amperes and it is approved
by ASTA or BSI to BS1362
Check for the ASTA mark or the BSI mark on the body of the
fuse.
If the plug contains a removable fuse cover you must ensure
that it is refitted when the fuse is replaced.
If you lose the fuse cover, the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
If the fitted moulded plug is unsuitable for the socket outlet in
your home then the fuse should be removed and the plug cut
off and disposed of safety.
There is a danger of severe electrical shock if the cut off plug is
inserted into any 13-ampere socket.
If a new plug is to be fitted please observe the wiring code as
shown below.
If in any doubt, please consult a qualified electrician.
2.3.2.1. Important
The wires in this mains lead are coloured in accordance with
the following code:
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings i dentifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the le tter N or coloured
BLACK.
The wire which is coloured BROWN must be connected to the
terminal in the plug which is marked with the letter L or coloured
RED.
Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with
the letter E or the Earth Symbol.
2.3.2.2. Before Use
Remove the Connector Cover as follows.
2.3.2.3. How to Replace the Fuse
1. Remove the Fuse Cover with a screwdriver.
2. Replace the fuse and attach the Fuse cover.
Blue Neutral
Brown Live
7
2.4. How to Replace the Lithium Battery
2.4.1. Replacement Procedure
1. Remove the MIC AMP P.C.B.. (Refer to Disassembly Procedures.)
2. Remove the Lithium battery (Ref. No. “B6401” at component side of MIC AMP P.C.B.) and then replace it into new one.
NOTE:
This Lithium battery is a critical component.
(Type No.: ML-614S/ZTK Manufactured by Energy Company, Panasonic Corporation)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for HDC-SD600 series, as well.
1. Battery Pack for this model.
2. Button-type battery for Remote controller (CR2025: Being supplied from Energy Company, Panasonic Corporation).
8
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2. General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical compone nts on the printed circuit bo ards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) mo re than th at of the
normal solder.
Distinction of P.C.B. Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the P.C.B. cleanly for solderin g of the new IC.
• Since the melting point of the lead free solder is high er than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C
(662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
3.3. Important Notice 1:(Other than U.S.A. and Canadian Market)
1. The service manual does not contain the following information, because of the impossibility of servi cing at component level
without concerned equipment/facilities.
a. Schematic diagram, Block Diagram and P.C.B. layout of MAIN P.C.B..
b. Parts list for individual parts for MAIN P.C.B..
When a part replacement is required for repairing MAIN P.C.B., replace as an assembled parts. (Main P.C.B.)
2. The following category is /are recycle module part. Please send it/them to Central Repair Center.
• MAIN P.C.B. (VEP03H98EN: HDC-SD600P)
• MAIN P.C.B. (VEP03H98EP: HDC-SD600EB/EC/EF/EG/EP)
• MAIN P.C.B. (VEP03H98EQ: HDC-SD600EE/GN)
9
3.4. How to Define the Model Suffix (NTSC or PAL model)
There are three kinds of HDC-SD600.
• a) HDC-SD600P
• b) HDC-SD600EB/EC/EF/EG/EP/GN
• c) HDC-SD600EE
What is the difference is that the “INITIAL SETTING” data which is stored in Flash ROM mounted on Main P.C.B..
3.4.1. Defining methods:
To define the model suffix to be serviced, refer to the rating label which is putted on the Unit.
NOTE:
After replacing the MAIN P.C.B., be sure to achieve model type setting and adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-A VC” web-site in
“TSN system”, together with Maintenance software.
10
3.5. Formatting
11
4 Specifications
12
13
14
5 Location of Controls and Components
1 Speaker
2 Power button [ ]
3 Inlet (cooling fan)
4 Intelligent auto/Manual button
[iA/MANUAL]
5 Optical image stabilizer button
[ /O.I.S.]
6 1080/60p button [1080/60p] (NTSC areas)
7 Battery release lever [BATT]
8 Battery holder
9 DC input terminal [DC IN]
Always use the supplied AC adaptor or a
genuine Panasonic AC adaptor.
10 HDMI mini connector [HDMI]
11 USB terminal [ ]
12 AV multi connector
Use the AV multi cable (only the supplied
cable).
13 Card slot
14 Access lamp [ACCESS]
15 Lens cover
The lens cover opens in Motion
Picture Recording Mode or Still
Picture Recording Mode.
16 Remote control sensor
17 Built-in flash
18 Lens (LEICA DICOMAR)
19 AF assist lamp
20 Recording lamp
10
89
2345
67
11
12
13
1
14
15
16
17
18
19
20
1080/50p button [1080/50p] (PAL areas)
21 LCD monitor (Touch screen)
It can open up to 90Q.
It can rotate up to 180Q towards the lens
or 90Qtowards the opposite direction.
22 Quick menu button [Q.MENU]
23 Sub recording start/stop button
This button functions in the same manner
as the recording start/stop button.
24 Adjust zoom buttons
25 Menu button [MENU]
26 Delete button [ ]
21
22 23 24 25
26
Due to limitations in LCD production
technology, there may be some tiny bright
or dark spots on the LCD monitor screen.
However, this is not a malfunction and
does not affect the recorded picture.
15
27 Tripod receptacle
27
28 Status indicator
29 Photoshot button [ ]
30 Zoom lever [W/T] (In Motion Picture
Recording Mode or Still Picture
Recording Mode)
Thumbnail display switch [ / ]/
Volume lever [UVOLT] (In Playback
Mode)
31 Internal microphones
32 Mode switch
33 Recording start/stop button
34 Shoulder strap fixture
35 Grip belt
Adjust the length of the grip belt so that it fits
your hand.
Flip the belt.
Adjust the length.
Replace the belt.
28 29 30 31
32
33 34 35
16
Change the mode to recording or playback.
Operate the mode switch to change the mode to , or .
Motion Picture Recording Mode
Still Picture Recording Mode
Playback Mode
Selecting a mode
Using with the remote
control
Select the menu.
1 Power on/off button [ ]
Unit can be turned on/off when the LCD
monitor is opened.
●
Unit cannot be turned on by the power on/
off button when 36 hours have passed after
the unit is turned off. Press the power
button on the unit and turn the unit back on.
●
Unit cannot be turned off when it is
connected to the PC or the DVD burner.
2 Photoshot button [ ]
*
3 On-screen display button
[EXT DISPLAY]
4 Playback operation buttons
These buttons function in the same manner
as the corresponding playback operation
icon being displayed on screen.
[Excluding skip playback]
5 Delete button [ ]
*
6 Direction buttons [,,,]
7 Zoom/volume/thumbnail display
switch buttons [T, W, /VOL]*
8 Recording start/stop button [START/
STOP]
*
9 Date/time button [DATE/TIME]
10 Menu button [MENU]
*
11 OK button [OK]
* means that these buttons function in the
same manner as the corresponding
buttons on the unit.
: [SETUP]
[REMOTE CONTROL] [ON]
SEARCH
STILL ADV STILL ADV
SEARCH
/VOL
DATE/TIME
START/
STOP
EXT DISPLAY
PLAY
STOP
OK
SKIP SKIP
MENU
PAUSE
2
3
4
6
5
8
7
9
10
11
1
You can operate by directly touching the
LCD monitor (touch screen) with your finger.
It is easier to use the stylus pen (supplied)
for detailed operation or if it is hard to
operate with your fingers.
Touch
Touch and release the touch screen to select
icon or picture.
Touch the center of the icon.
Touching the touch screen will not operate
while you are touching another part of the
touch screen.
About the operation icons
///:
These icons are used to switch the menu
and thumbnail display page, for item
selection and setting etc.
:
Touch to return to the previous screen
such as when setting menus.
Do not touch on the LCD monitor with
hard pointed tips, such as ball point pens.
Perform the touch screen calibration when
the touch is not recognized or wrong
location is recognized.
How to use the touch
screen
17
6 Service Mode
1. Indication method of the service menu
Set the mode switch “Motion Picture Recording” mode.
2. Turn the power on, and then while keep pressing the “Zoom lever” to W side, “Intelligent auto/Manual” button and “Menu” button for more than 3 seconds until the top screen of the Service Mode Menu being displayed.
Service mode menu
NOTE:
Do not using service mode except above table of Service mode menu.
3. End method of the top screen of the service mode menu
Push the “Menu” button to end the service mode, and then POWER OFF.
Screen display Contents Function
1 Factory settings Function to throw a product up in a factory shipment state
(When recorded data in Built-in memory, “error display” is done)
4 Lock search history indication Display the camera system error code for three histories saved
in EEPROM
5 Power ON self check result display Power ON self check (function to diagnose correct function of
the device and interface between devices) result display
18
6.1. Lock Search History Indication
Touch the [ 4 ] of LCD, select Lock search history indication.
Operation specifications
Indication contents
• Lock search history indication
Display the camera system error cord for three histories saved in EEPROM.
• The error cord contents which are displayed
Push the “Menu” button to end the service mode, and then POWER OFF.
6.2. Power ON Self Check Result Display
Touch the [ 5 ] of LCD, select Power ON self check result display.
Operation specifications
Indication contents
• Power ON self check result display
Function to diagnose correct function of the device and interface between devices result display.
Display the following commnucation test result.
- CAM-PWR : Commnucation test between IC2006 to IC301
- CAM-UNI : Commnucation test between IC3401 to IC301
Display other than “OK” are abnomalities of each lines.
Cutting of battery connection or AC power supply connection to end the service mode.
Error code Function
51 Focus control is abnormal
52 Zoom control is abnormal
53 OIS lens control is abnormal
71 Lens cover open/close is abnormal
72 Cooling fan is abnormal
73 High temperature is abnormal
33 Communication between camera to ARM is abnormal
19
7 Service Fixture & Tools
7.1. When Replacing the Main P.C.B.
After replacing the Main P.C.B., be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in
“TSN system”, together with Maintenance software.
7.2. Service Position
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
CAUTION-1. (When servicing FLASH P.C.B.)
1. Be sure to discharge the capacitor on Flash P .C.B..
Refer to “How to Discharge the Capacitor on Flash P.C.B.”.
The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.
2. Be careful of the high voltage circuit on Flash P.C.B..
3. DO NOT allow other parts to touch the high voltage circuit on Flash P.C.B..
No. Parts No. Connection Form
1 RFKZ0444 PP6005( Main ) - PS601( Batt. Catcher ) 50PIN 0.5 B to B
2 VFK2020 PS6002( Main ) - FP4802( MIC AMP ) 20PIN 0.5 B to B
3 VFK1933 PS6003( Main ) - Monitor FPC 34PIN 0.5 B to B
4 VFK1950 FP6001( Main ) - FP6403( Front ) 33PIN 0.3 FPC
5 VFK1870 PP6006( Main ) - PS7001( Flash ) 30PIN 0.5 B to B
6 RFKZ0416 FP6002( Main ) - Lens Unit 41PIN 0.3 FPC
20
8 Disassembly and Assembly Instructions
8.1. Disassembly Flow Chart
This is a disassembling chart.
When assembling, perform this chart conversely.
8.2. PCB Location
21
8.3. Disassembly Procedure
No. Item Fig Removal
1 Side Case (L) Unit Fig.D1 2 Screws (A)
4 Screws (B)
2 Locking tabs
Sensor Cover Unit
Fig.D2 3 Screws (C)
2 Locking tabs
Side Case (L) Unit
2 Cover Board Unit Fig.D3 1 Screw (D)
2 Screws (E)
1 Screw (F)
1 Rib
Cover Board Unit
3 Top Case Unit Fig.D4 3 Screws (G)
1 Screw (H)
2 Screws (I)
2 Locking tabs
1 Rib
SR Cover
Fig.D5 PS6002 (Connector)
1 Rib
Top Case Unit
4 F ront Unit Fig.D6 P7001 (Connector)
P7002 (Connector)
Fig.D7 1 Screw (J)
1 Rib
1 Locking tab
FP6403 (Flex)
Front Unit
5 Side Case (R) Unit Fig.D8 4 Screws (K)
PS6003 (Connector)
FP6501 (Flex)
Side Case (R) Unit
6 Batt. Case Unit Fig.D9 1 Screw (L)
1 Screw (M)
2 Ribs
PP6005 (Connector)
Batt. Case Unit
7 Lens Unit Fig.D10 2 Screws (N)
1 Rib
2 Projection parts
Fig.D11 PP6004 (Connector)
PP6007 (Connector)
FP6002 (Flex)
1 Screw (O)
Lens Frame Unit
Lens Unit
8 Main P.C.B. Unit Fig.D12 3 Screws (P)
2 Ribs
Main Heat Radiation Plate
Fig.D13 PP6006 (Connector)
1 Projection part
Main P.C.B. Unit
9 Flash P.C.B. Unit Fig.D14 2 Screws (Q)
1 Projection part
10 Side-R P.C.B. Unit
Speaker
Fig.D15 2 Screws (R)
SP Angle
PS6502 (Connector)
P6501 (Connector)
Speaker
Side-R P.C.B. Unit
Fig.D16 NOTE: (When Installing)
11 Fan Motor Fig.D17 3 Convexes
Fan Damper
Fan Motor
12 LCD Case Unit Fig.D18 2 Screws (S)
Holder
Switch Unit
3 Locking tabs
Earth Plate
Sheet
Light Guide Plate
3 Ribs
LCD Case Unit
13 Monitor P.C.B. Unit Fig.D19 FP904 (Flex)
FP905 (Flex)
2 Ribs
2 Convexes
LCD Frame
Fig.D20 FP903 (Flex)
4 Locking tabs
Monitor P.C.B. Unit
Fig.D21 1 Locking tab
Reflection Sheet
Light Guide Plate
Diffusion Sheet
Prism Sheet B
Prism Sheet A
Lens Holder
Monitor P.C.B. Unit
14 Front P.C.B. Unit Fig.D22 1 Screw (T)
1 Screw (U)
FP6400 (Flex)
Front P.C.B. Unit
15 Barrier Motor Unit Fig.D23 1 Screw (V)
Barrier Motor Unit
Fig.D24 NOTE: (When Installing)
16 Front Case Fig.D25 Lens Ornament Sheet
Fig.D26 4 Screws (W)
Front Case
17 SS SW P.C.B. Unit Fig.D27 2 Screws (X)
P6551 (Connector)
SS SW P.C.B. Unit
18 Top Frame Cover
Multi-Button Switch
Unit
Fig.D28 6 Screws (Y)
1 Locking tab
1 Rib
IA/OIS Button
Top Frame Cover
Multi-Button Switch Unit
19 MIC AMP P.C.B. Unit Fig.D29 FP4802 (Flex)
P4801 (Connector)
FP4801 (Flex)
Flex
Connector
MIC AMP P.C.B. Unit
20 ECM FPC Fig.D30 1 Screw (Z)
Fig.D31 MIC Damper
MIC Case
ECM FPC
21 Batt. Catcher P.C.B.
Unit
Fig.D32 1 Screw (a)
1 Locking tab
Rear Frame
3 Locking tabs
Batt. Catcher P.C.B. Unit
22 MOS Heat Radiation
Plate
Fig.D33 1 Screw (b)
MOS Heat Radiation Plate
23 Prism Unit
Optical Filter
FIg.D34 2 Screws (c)
Prism Unit
Optical Filter
No. Item Fig Removal
22
8.3.1. Removal of the Side Case (L) Unit
Fig.D1
24 IRIS Unit Fig.D35 18 Solders
3 Screws (d)
3 Ribs
IRIS Unit
25 Zoom Motor Fig.D36 2 Screws (e)
Zoom Motor
26 1st Lens Frame Unit Fig.D37 3 Screws (f)
1st Lens Frame Unit
27 2nd Lens Frame Move
Unit
Fig.D38 2nd Lens Frame Move Unit
Spring
2nd Lens Frame Move Unit
28 Body Unit
Zoom Guide Pole
Fig.D39 3 Screws (g)
Body Unit
2 Zoom Guide Poles
29 Master Flange Cover Fig.D40 2 Screws (h)
Master Flange Cover
30 4th Lens Frame Move
Unit
Fig.D41 2 Side Yorks
Fig.D42 3 Ribs
4th Lens Frame Move Unit
31 Focus Guide Pole L
Focus Guide Pole S
Fig.D43 Focus Guide Pole L
Focus Guide Pole S
No. Item Fig Removal
23
Fig.D2
8.3.2. Removal of the Cover Board Unit
Fig.D3
Loading...