Index ............................................. 103
ii Contents
Page 5
SAFETY FIRST
Y our new phone is a convenient and ef fec tive communic ations to ol, but it can be haz ardous when
used improperly. To avoid harming yourself or anyone else, please review the following
information before us ing your phone.
BATTERIES
Batteries can cause property damage, injury, or burns if the terminals are touched with a
conductive material (for example, metal jewelry, keys, and so on). Therefore, use caution when
handling a charged battery. Additional precautions and notes are listed below:
• Never throw a battery into a fi re; it may explode.
• Fully recharge the batter y if the battery is low or as soon as the low-battery alert beeps.
• Do not drop the battery.
• Do not allow bridging of battery contacts with metallic objects.
• Do not remove the battery f r om the phone while the phone is powered on. Settings you have
changed may revert to their previous settings.
A recyclable lithium ion/polymer battery powers your phone. Please call
1-800-8-BATTERY for information on how to recycle the battery.
CHARGING DEVICES
Use only Genuine Panasonic charging accessories. Use of attachments not recommended by
Panasonic or your wireless service provider may result in fire, electrical shoc k, or injury.
Panasonic is not responsi ble for damage caused by using non-Panasonic accessories.
• Do not expose charging adap ters to moisture, water, or the weather.
• Do not use an adapter with a damaged c ord.
• When using a DC adapter in an automobile, a small amount of electricity flows thr ough the
adapter, even if the phone is turned off. Remove the plug from the cig arette lighter whenever
the phone will be left in the vehicle for long periods of time.
• Always charge the battery in a well ventilated area, not in direct sunlight, between 41°F (5°C)
and 95°F (35°C). It is not possi ble to recharge the battery if it is outside this temperature
range.
• Do not incinerate or disp ose of the battery as ordinary trash. The battery must be dis posed of
in accordance with local legislation and may be recycled.
Caution: The cigarette lighter must have a 12V negative ground socket. Do not use the adapter
in a vehicle that has a positive ground system.
GENERAL
• Do not use the phone in extreme temperature or humidity. The specified operating
temperature range is -22°F to +140°F (-30°C to +60°C).
• Extreme temperatures may ha ve a temporary effect on the operation of your phone. This is
normal and does not indicate a fault.
• Do not expose the phone (particularly the display) to direct sunlight for exten ded periods of
time or to a humid, dusty or hot ar ea.
• Do not attempt to disassemb le the phone. There are no user-servic eable parts inside.
• Do not subject the equipment to excessive vibration or shock.
• Do not expose the phone to rain or spill liquids on it. If the equipment becomes wet
immediately remove the battery and charging device and contact yo ur dealer.
• Do not carry the phone by holding the antenna.
Safety F irst 1
Page 6
• Do not use any accessorie s ot her than those designed fo r use with your phone.
• Use of attachments not recommended or sold by Panasonic or your wireless service provider
may result in fire, electrical shock, or injury.
• Panasonic is not responsi ble for damages caused by using non-Panasonic accessories.
• Pressing any of the keys may produce a loud tone. Avoid holding the phone close to the ear
while pressing the keys.
• Keep metallic items that may accidentally touch the batt ery terminals away from the
equipment. Battery damage may occur.
• When disposing of any p acking mate rials o r old equi pment check with your local authorit ies for
information on recycling.
• If connecting the ph one to an exter nal sourc e, read t he opera ting instru ctions of th e equipment
for the correct connection and s afety precautions.
• If connecting the phone to an external source, verify that the phone is compatible with the
product to w hich you are co n n ecting it.
AVAILABILITY OF SERVICE
This phone, like any wireless phone, operates using radio signals, wi reless and landline
networks, and user-programmed functions. Because of this , connection in all conditions cannot
be guaranteed. Therefore, you should never rely solely on any wire l ess phone for essential
communications (for example, medical emergencies).
EMERGENCY (911) SERVICE
If you need to make an emergency (911) call, power the phone on, dial 911, and press .
Emergency calls can be made regardless of lock setting and with or without a SIM car d.
Remember, to make or receive an y call, the pho ne must be s witched on an d in a service ar ea that
has adequate signal strength. Even if you are within the coverage area of your wireless service
provider, you may be in an area with insufficient signal strength to place a 911 call. Emergency
calls might not be possible on all wireless phone net works or when cert ain network service and/ or
phone features are in use.
CALL REJECTED
Your phone displays Call Rejected under the following conditions:
1. Call was not able to c onnect to t he network (no c ir cui ts ava ilabl e, no sig nal availab le o r ou t o f
service area).
2. Battery charge level is to o low (recharge battery).
3. Your calling plan is expired, depleted or has reached its preset limit.
Note: Emergency (911) Service is still available.
SAFETY TIPS
Following the suggestions in this section will help ensure safe an d efficient operation of your
Panasonic phone.
This Model Phone Meets The Government’s Requirements For Exposure To Radio Waves.
Your wireless phone is a radio transmitt er and receiver. It is designed and manufactured not to
exceed the emission limits for exposure to radiofreque ncy (RF) energy set by the Federal
Communications Commission of the U.S. Government. These limits ar e part of comprehensive
guidelines and establis h permitted levels of RF energy for the general populat i on. The guidelines
are based on standards that were developed by independent scientific organizations through
periodic and thorough evalu ation of scientific studies. The standards include a substantial safety
margin designed to assure the safety of all persons, regardless of age and health.
2 Safety First
Page 7
The exposure standard for wireless mobile phone s employ s a unit of measure ment kno wn as the
Specific Abs orption Rate, or SAR. The SAR limit set by t he F CC is 1. 6W/kg. Tests for SAR are
conducted using st a ndar d opera tin g pos itions specif ied by t he F CC with th e p hone t ran smitt ing at
its highest certified power level in all tested frequency bands. Although the SAR is determined at
the highest certified power level, the actual SAR level of the phone while operating can be well
below the maximum value. This is because the phone is designed to operate at multiple power
levels so as to use only the power required to rea ch the network . In gene ral, th e close r you are t o
a wireless base station antenna, the lower the power output.
Before a phone model is availa ble for sale t o t he public , it mu st be te sted and c er tifie d to th e FCC
that it does not exceed the limit established by the government-adopted requirement for safe
exposure. The test s are performed in positions and locations (e.g., at the ear and worn on the
body) as required by the FCC for each model. The highest SAR value for this model phone when
tested for use at the ear is 0. 982 W/kg and when worn on the body, as described in this user
guide, is 0.364 W/kg. (Body-worn measurements differ among phone models, depending upo n
available accessories and FCC requirements). While there may be differences between the SAR
levels of various phones and at various positions, they all meet the go vernment requirement for
safe exposure.
The FCC has granted an Equipment Authorization for this model phone with all reported SAR
levels evaluated as in compliance with the FCC RF emission guidelines. SAR inf ormation on this
model phone is on file with the FCC and c an be found under the Display Grant s ection of http://www.fcc.gov/oet/fccid after searching on FCC ID NWJ10A008A.
Additional information on Specific Absorption Rates (SAR) can be found on the Cellular
Telecommunications Industry Association (CTIA) web-site at http://www.wow-com.com
Caution: All Panasonic branded accessories are tested and comply with FCC RF exposure
requirements. Non-Panasonic accessories may not comply.
.
BODY-WORN OPERATION
This device was tested for typic al body-worn operations using the carry case model:
EB-YKD87, which provides 3.0 cm. separation distance from the body. This device was also
tested for body-worn ope rations with the back of the phone kept 1.5 cm. from the body. To
maintain compliance with FCC RF exposure requirements, use only belt-clips, holsters or similar
accessories that maint ain a 1.5 cm. sep ar ati on dis ta nce bet ween the user’s bod y and the back of
the phone, including the antenna. The use of belt-clips , holsters and similar accessories should
not contain metallic components in its assembly. The use of accessories that do not satisfy these
requirements may not comply wit h FCC RF expos ure requirements, and should be avoi ded.
ANTENNA CARE
Do not use the phone with a damaged ant enna. Use only the supplied or an approved
replacement antenna. Unauthorized antennas, modifications, or attachments could damage the
phone and may violate FCC regulations.
PHONE OPERATION
Normal Position: Hold the phone as you would any other tele phone, with t he ante nna pointed up
and over your shoulder.
For Efficient Operation: For your phone to operate most efficient l y, do not touch the antenna
unnecessarily when the phone is in use. Contact with the antenn a affects call quality and may
cause the phone to operate at a higher power level than otherwise needed.
Safety F irst 3
Page 8
DRIVING
Important: Check the laws and re gulations on the use of wireless telephones in the areas where
you drive. Always obey them. Also, if using your phone while driving:
• Give full attention to driving—driving safely is your first responsibility;
• Use handsfree operation, if available;
• Pull off the road and park before making or answering a call if driving conditions so require.
ELECTRONIC DEVICES
Most modern electronic equipme nt is shielded from RF signals. However, certain electron ic
equipment may not be shielded against the RF signals from your wireless phone.
Pacemakers: The Health Industry Manufacturers Associatio n recommends that a minimum
separation of 6 i nches (6 ”) o r 15 centimet ers (1 5 cm) b e mai nt ained bet ween a h and held wireles s
phone and a pacemaker to avoid potential interference with the pacemaker. These
recommendations are consistent with independent research and recommendations of Wireless
Technology Research.
Persons with pacemakers:
• Should ALWAYS keep the phone more than six inches from their pacemaker when the phone
is turned ON;
• Should not carry the phone in a breast pocket;
• Should use the ear opposite the pacemaker to minimize the potential for interference ;
• If you have any reason to suspect that interference is taking place, turn your phone OFF
immediately.
Hearing Aids: Some digital wireless p hones may interfer e with some hearing aids. In the even t of
such interference, consult yo ur wireless service provider and hearing aid manufacturer.
Other Medical Devices: If you use any other personal medical device, consult the manufacturer
of your device to determine if it is adequately shielded from external RF energy. Your physician
may be able to assist you in obtaining this information.
Turn your phone OFF in health care facilit ies when any regulations posted in these areas instruct
you to do so. Hospitals or health care facilities may be using equipme nt that could be sensitive to
external RF energy.
Vehicles: RF signals may affect improperly installed or inadequately shielded electronic systems
in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You
should also consult the manufacturer of any equipment that has been added to your vehi cle.
Posted Facilities: Turn your phone OFF in any facility where posted notices so require.
AIRCRAFT
FCC regulations prohibit using your phone while in the air; switch off your phone before boarding
an aircraft unless otherwise advised by airline personnel.
BLASTING AREAS
To avoid interfering with blasting operations, turn your phone OFF when in a “blasting area” or in
other areas posted: “Turn off two-way rad i o.” Obey all signs and instructions.
4 Safety First
Page 9
POTENTIALLY EXPLOSIVE ATMOSPHERES
Turn your phone OFF when in any area with a potentially explos ive atmosphere and obey all
signs and instructions. Sparks in such areas could cause an explosion or fire resulting in bodily
injury or even death.
Areas with a potentially explosi ve atmosphere are often, but not always, clearly marked. They
include fueling areas such as gas stations; below deck on boats; fuel or chemical transfer or
storage facilities ; v ehicles using liquefied petroleum gas (such as propane or but ane); areas
where the air contains c hemicals o r partic les, such as grain, dus t or metal powders; an d any other
area where you would normally be advised to turn off your vehicle engine.
FOR VEHICLES EQUIPPED WITH AN AIR BAG
An air bag inflates with great f orce. DO NOT place objects, including both installed or portable
wireless equipment, in the area ov er the air bag or in the air bag deployment area. If in-vehicle
wireless equipment is improperly ins talled and the air bag inflates, se rious injury could result.
For U.S. Customers: Vehicles using liquefied petroleum gas (suc h as propane or butane) must
comply with the National Fire Protection Standard (NFPA-58).
For a copy of this standard, contact:
National Fire Protection Association
One Batterymarch Park
PO Box 9101
Quincy, MA 02269
Phone: 1-800-344-3555
Web site: www.nfpa.org
E-mail address: Custserv@NFPA.org
See “Appendix C: Consumer Update” starting on page97 for the FDA Consumer Update on
Mobile Phones published by the U.S . Food and Drug Administration.
Safety F irst 5
Page 10
TEN (10) DRIVER SAFETY TIPS
Y our wirel ess teleph one gives you the p owerful abili ty t o communicate by voice-a lmost any where,
anytime. But an important responsibility accompanies the benefits of wireless phones, one tha t
every user m ust uphold.
When driving a car , driv ing is your fir st respon si bility. When using your wireless phone behind the
wheel of a car, practice good common sense and remember the following tips:
1. Get to know your wireless phone and its features such as speed dial and redial. If
available, these features help you to place your call without taking your attention off the
road.
2. When available, use a hands free device. If possible, add an additional layer of
convenience and safety to your wireless phone with one of the many hands free
accessories available today.
3. Position your wireless phone within easy reach. Be able to access your wireless
phone without removing your eyes from the road. If you get an incoming call at an
inconvenient time, if possible, let your voice mail answer it for you.
4. Let the person you are speaking with know you are driving; if necessary,
suspend the call in heavy traffic or hazardous weather conditions. Rain, sleet,
snow, ice, and even heavy traffic can be hazardous.
5. Do not take notes or look up phone numbers while driving. Jotting down a "to do"
list or flipping through your address book takes attention away from your primary
responsibility, driving safely.
6. Dial sensibly and assess the traffic; if possible, place calls when you are not
moving or before pullin g into traffic. Try to plan calls when your car will be
stationary. If you need to make a call while moving, dial only a few numbers, check the
road and your mirrors, then continue.
7. Do not engage in stressful or emotional conversations that may be distracting.
Make people you are talking with aware you are driving and suspend conversations
that have the potential to divert your attention from the road.
8. Use your wireless phone to call for help. Dial 9-1-1 or other local emergency number
in the case of fire, traffic accident or medical emergencies. Remember, it is a free call
on your wireless phone!
9. Use your wireless phone to help others in emergencies. If you see an auto
accident, crime in progress or other serious emergency where lives are in danger, call
9-1-1 or other local emergency number, as you would want others to do for you.
10. Call roadside assistance or a special non-emergency wireless assistance
number when necessary. If you see a broken-down vehicle posing no serious hazard,
a broken traffic signal, a minor traffic accident where no one appears injured, or a
vehicle you know to be stolen, call roadside assistance or other special non-emergency
wireless number.
"The wireless industry reminds you t o use your phone safely when driving."
For more information, please c all 1-888-901-SAFE or
visit www.wow-com.com
Information on this pa ge provided by the Cellular Telecommunications Industry
Association.
6 Safety First
Page 11
PREPARING YOUR PHONE FOR USE
Thank you for purchasin g th e Panasonic GU87 GSMTM/
GPRS mobile phone. This phone operates on the Global
System for Mobile Communications (GSM) networks
around the world, which pro vides integrated voice mail,
short message servic e ( SMS), multimedia messa ging
service (MMS), fraud protection and superior voice quality.
One of the most i m portant GSM advantage s i s the
removable SIM (subscri ber id entity module) card, which
holds personal inform at ion such as phone numbers,
missed calls, voice ma il and text message notifications.
FEATURE
AVAILABILITY
BEFORE USING
YOUR PHONE
INSTALLING SIM
CARD
Some features are network dependent or may be available
only if you subscribe. Some fu nct ions are SIM card
dependent. Note that before you can take advantage or
even activate many of the net w ork features offered by the
networks , you must subscr i be to the desired services . For
more information, contact your wireless service provider.
The SIM card must be installed in your phone for it to
operate on the cellular ne tw or k. In ser t S IM card, then
attach battery and fully charge it.
1. Remove perforated SIM card from larger plastic card.
2. Turn off phone (press and hold ), remove battery,
and if necessary, remove previous SIM card.
3. Locate small recessed area on back of phone near
bottom. Hold SIM card vertically with gold side face
down and notched corner on the upper left. Then, slide
SIM card down into recesse d ar ea.
• SIM card should not ov erlap SIM car d l atch.
Preparing Your Phone For Use 7
Page 12
4. Replace battery (see “Attaching Battery” below) and
turn on phone (press and hold ).
• If SIM card is insert ed in corr ectl y or is dama ged , No
SIM Present or SIM ERROR m ay display. Remove SIM card (see below) then repeat steps 2 to 4.
• If phone di spl ays SIM ERROR, Invalid SIM or SIM
BLOCKED/Contact Service Provider, cont act your
wireless service prov i der .
REMOVING SIM
CARD
ATTACHING
BATTERY
REMOVING
BATTERY
1. Turn off phone and remove battery.
2. While pressing down on SIM card latch, slide SIM card
up and lift it out of the recessed area on back of phone.
1. On back of phone, hold battery at
2. Push bottom of battery dow n
1. Slide batt er y latc h t oward bott om
2. Lift and remove battery.
º
angle; insert tabs on top
a 45
edge of battery into slots along
top edge of battery area.
until it clicks into place.
of phone.
8 Preparing Your Phone For Use
Page 13
CHARGING
BATTERY
Verify that battery is attached to phone.
1. Plug Rapid
Charger i nto a
standard AC
wall outlet.
2. Plug Rapid
Charger
connector into
base of ph one
(with arrows
facing up).
• DO NOT
force the connector: it m ay damage the phone and/
or Rapid Charger.
• During charging, the battery charging icon
flashes on the main disp la y and on the sub display;
the red indicator light on front of phone lights.
• The batt er y achieves maximum perfor m ance after
two or three charges.
3. When charging is complete, the charging icon and red
indicator light turn off. Press in both side tabs on the
Rapid Charger connector and pull it gently from phone.
Unplug Rapid Charger from wall outlet.
Low Battery Warning
Charging Tips
LOW BATTERY flashes and a warning tone sounds;
phone will automatically turn off. Fully recharge battery. If
you receive the low battery warning dur ing a conv ersation,
finish your call immediately.
• Always charge batteries in a well-ventilated area, not in
direct sunlight, between 41°F (5°C) and 95°F (35°C).
• Temperature may slightly affect charging tim e. I n
extreme temperatures, the battery will stop charging;
the indi cator l ight and ch argi ng icon change s:
occurs, remove charger, return phone to an acceptable
temperature level, and reconnect charger.
• It is normal for your battery to become warm to the
touch while being recha rg ed.
Preparing Your Phone For Use 9
. If this
Page 14
• Fully charge battery for recommended time. You can
use phone during char gi ng, but doing so extends
charging time.
Battery
Specifications
Talk TimeStandby TimeCharge Time
Up to 3 hoursApprox. 150 hoursApprox. 90 minutes*
*Based on using the EB-CA370 700 mAh Rapid Charger.
Note: Times are approximate and may vary bas ed on
network configurati on, signal st r ength, features select ed,
and phone usage. Exten ded gaming, camera use, or
internet browsing will reduce battery life. You can set key
backlighting to OFF to he l p extend batt ery life.
PRIVATE HANDSFREE
HEADSET
When the Private
Handsfree Headset is
plugged into the phone,
you can have a phone
conversation withou t
holding the phone to
your ear. Y ou can hear
the other person’s voice
through the Private
Handsfree Headset’s
earpiece. When you
speak, your voice is
picked up by the Private
Handsfree Headset’s
microphone.
1. Pull cap out from jack
2. Attach clip to your
3. Insert earpiece into
on the side of the
phone and securely
plug in the Private
Handsfre e H eadset
connector. This will
automatically disable
the phone’s speaker
and microphone.
clothes.
Note: Attach clip to
wire by holding back
of clip and wire
between th um bs and
forefingers, then push
wire into wire holder.
your ear.
10 Preparing Your Phone For Use
Page 15
4. When phone rings, press and hold Send/End button on
the Private Handsfree Headset until the call connects.
OR
Set your phone to automat ic al ly answer calls. See
“H’Free Auto Ansr” on page 75.
5. During conv ersa ti on, i ncrea se o r decr eas e vol ume to a
comfortable level by pressi ng the top or bottom of the
navigation key. The microphone picks up you r vo i ce
from its hanging position. The Voice Memo Key on the
flip flashes while call is connected.
6. When the conversatio n i s ove r, press and hold the
Send/End button on the Priv ate H andsfree Headset
until the call is disconnected.
7. To make a call, dial t he phon e nu mber fr om th e key pad
and press . For v oice dialing, press the Send/End
button and say the voice dial command after the beep.
Note: You must record voice dial entries before using
voice dialing. See “Voice Dialing” on page 60.
Warnings:
• If ring volume is set to the loudest ring, ringing may be
uncomfortably loud during handsfree use. Check rin g
volume before enabling handsfree use to ensure
volume is set to an acceptable level.
• The use of an ear in ser t de vice whi le dr iv ing m ay v iol ate
the laws of some states/provi nc es. Be sure to check
applicable state/provincial laws before using this device.
Preparing Your Phone For Use 11
Page 16
ACCESSORIES
Many accessories are available for your Panasonic phone.
Contact your wireless service provider to purchase
Genuine Panasonic accessories. Using non-P anasonic
accessories or acce sso ri e s not recommended by your
wireless service provider may resul t in poor performance
of your phone, or even caus e an electrical hazard.
Replacement antennas are available from Pana sonic.
• In the U. S., ca ll 1 (8 00) 833-9626.
• In Cana da, contact your cellular dealer.
Note: Replacement ant ennas are shipped with removal
and assembly instructions. Do not attempt to remove the
existing antenna until the replacement antenna is received.
Battery
(EB-BSU87S)
Li-Ion 720 mAh
Rapid Charger
(EB-CA370)
DC Adapter
(EB-CD300)
Carry Case
(EB-YKD87)
Car Hold er
(EB-KAD87)
12 Preparing Your Phone For Use
Private Handsfree
Headset
(EB-EMD87)
Serial Data Cable
(EB-RSD67B) with
charging capability
Page 17
PHONE OVERVIEW
Note: See “Camera Menu” on
page 35 for items that operate
differently during camera use.
Phone Overview 13
Page 18
KEY FUNCTIONS
KeyFunction
Navigation Key: Scroll/move through menus, t ext and Phoneboo k, and select and
save settings. Also serves as a shutter button for the camera.
SELECTPress center to select option or to save.
SCROLL
MOVE
Left Softkey: Perform function displayed in lower left corner of main display. From
standby, press to open phonebook. From main menu page, short cut to MMS inbox.
Right Softkey/Cancel or Exit Key: Perform function displayed in lower right
corner of main display. Primarily used to cancel and return to previous menu level,
or to delete text/number entries. From standby, press to use shortcut. (Default is
shortcut to camera. To change shortcut, see “Short Cut Key” on page74.)
Send Key: Make a call or recall recently dialed phone numbers.
Power/End Key: Whe n ph one i s on, press br ief ly to end a c all or return to st andby.
Press and hold to turn phone on/off. Press to disconne ct Browser.
1 Key/V o ice Mail Key: Press and hold to call voice mail message center.
to
1-9 Digit Keys: Enter numbers. Press and hold a single key (2-9) for Speed Dial.
In text entry mode; enter text, numbers and characters; press and hold 1 key to
scroll for punctuation. While viewing menu options, press correspo nding number
key to go directly to that option.
Pause Key: Press and ho ld to en te r a p a use or wa it ti me. Wh en in th e fi rst p os iti on
of a phone number, pressing and holdin g will toggle between 0, + ( the int ernational dialing prefix) and _ (wildcard number). See “International Dialing” on page 19, “Wildcard Numbers” on page 60, and “Touch Tones (DTMF)” on page 22.
In T9 text entry mode, press for other word choices.
Press top or bottom edge to move on-screen cursor
up or down. Press and hold to move page by page.
From standby, press and hold for voice dialing (if set).
Press left or right edge to move on-screen cursor left
or right.
14 Phone Overview
Page 19
KeyFunction
Asterisk Key: In text entry mode, press to switch among all lowercase letters, first
letter capital, and capitals lock methods.
Quiet Mode Key: From standby, press and hold to turn Quiet Mode (vibration) on/
off. (Note: This is the def ault setting and works only if the Quiet Mode vibration
setting remains On. See “Quiet Mode” on page 74.) In text entry mode, enters
space.
Operator Key: (located at the bottom left side of the keypad). From standby, press
and hold to open the browser (inter net access) and access mMode
to Browser menu.
Note: The icon or graphic on key may vary depending on your wireless service
provider.
Vo ice Memo (Multi-Function) Key: (located under sub display on front of phone).
Shutter button when taking self-portraits. Lights sub display and toggles date/time.
Start/stop voice recording during conversation.
DISPLAYS, MAIN AND SUB
Main DisplaySub Display
The sub display is the small display screen
located on the outside of the phone.
SM. Press to go
After some operations, the d ispl ay automatically clears after three seconds or after
pressing any key.
Phone Overview 15
Page 20
Different icons appear depe ndi ng on the features you are using and the options you
have selected. Some icons appear on both the main dis play and the sub display as
shown in the following table.
Icon IndicatesIcon Indicates
Roaming (registered to a non-home
network)
Line selection 1
(SIM card dependent)
Call forwarding (call divert) is onNew MMS message received
TTY Mode enabledMMS message storage area is full
New SMS message received
SMS message storage area is fu ll
New Push message received
GPRS service is available
Four levels indicate signal st rength
from network on which phone is
currently registered
Three levels indicate battery charge
level; low, medium, high
Battery is chargingShortcut key to preset menu item
All ring tones/ring volume are off
Vibration alert is on
Quiet mode is onCamera menu; brightness level 0
New voice mail message receivedCamera menu; wide view
Phone lock is onCamera menu; close up view
Alarm is setCamera menu; go to menu options
Download dataCamera menu; shutter button
MMS sound on
MMS sound muted
MMS volume control;
number indicates volume level
Key guard is on
Shortcut to Phone book
Navigation key scrolling and moving
options
Camera menu; picture will save in JPG
format
16 Phone Overview
Page 21
PHONE BASICS & MANAGING CALLS
ON/OFF
Press and hold .
• When turning the phone on, first there is a brief
animation, then the standby display comes on.
• If the phone is locked,
lock code and press
page 87.
• If your SIM card is PIN protected, your PIN code will be
requested. Enter the PIN code and press . See “PIN or PIN2” on page88.
displays. Enter the 4-digit
(Ok).
See “Lock Phone” on
STANDBY MODE
MAKING CALLS
The standby display shows th e name of the wireless
service provider, signal strength and bat tery level icons,
as well as shortcut to Phone book, Menu and preset
shortcut key icons. It can also display the current monthly
calendar, current time/date, and GPRS ( if ava i la bl e) ic on.
• Press
change the look of the standby display, such as the
background picture (wallpaper) or add/remove the
calendar. See “Display Settings” on page 72.
• Press
• Press
menu item. Default setting is Camera.
There are man y ways to make calls as described in this
chapter. Phone must be on and network coverage must
be available.
• To make a call, start in standby mode.
• During a call, scroll up or down to adjust ear pi ece
volume.
• Before dialing a number from the SIM or Mobile
Phonebooks, first program and save the number in the
Phonebook. See “Create” on page 58. To update a
phonebook number, see “Search” on page 57.
• Before using voice dialing, first record a voice dial
entry. See “Voice Dialing” on page 60.
(Menu) to access the ma i n menu. You can
() to access your Phonebook.
() to access the shortcut to your preset
Phone Basics & Managing Calls 17
Page 22
• For an e m er gency call, dial 911 and press . (911
dialing works even if the phone does not have a SIM
card or if the phone is locked. )
• If a call do es not connect, press
to automatically redial the num ber (up to 10 times).
The phone beeps when the ca ll connects. To cancel
redial, press .
Warning: Shutting the fli p dur ing a cal l DOES NOT
end the call. Opening the fli p ag ai n al l ows you to
return to your previous conv er sation.
Standard Dialing1. Open flip.
2. Dial phone number and press .
• To erase digits and re-enter before sending,
press (C).
Phonebook Dialing1. Press.
• The m ost re cently viewed phonebook (SI M or
Mobile) opens. To open the other phonebook, see
“Search” on page 57
2. Scroll to desired phonebook entry.
3. Press
when Ok displays
.
.
Location Number
Dialing
(SIM Phonebook)
1. Enter SIM phonebook locati on number.
2. Press .
Note: This feature only dials from the SI M phonebook. It
is not available from the Mo bi le phonebook.
Speed Dialing1. Press and hold numbered key
corresponds to phone book location number 2 - 9.
• You must choose which phonebo ok t o use. See
“Speed Dial Setup” on page 64 .
2. Press
Note: Some speed dial keys may be r eserved by your
wireless service provider. For example, the key may
be assigned for one-touch voice mail retrieval.
18 Phone Basics & Managing C all s
.
to
that
Page 23
Voice Dialing1. To record a voice command , s ee “Voice Dialing” on
page 60.
2. From standby, press and hold the top or bottom of the
navigation key until Please Call Voice Dialing
displays.
3. Clearly say the name (e xactly as recorded) and wait.
• Phone num ber and Voice Dial entry are repeated.
• If phone d oe s not recognize your voice com m and,
Failed Please Retry displays.
4. To initiate the call, press .
Last Number Dialing1. Press
Recent Number
Dialing (Calls Made
or Received)
Returning an
Unanswered Call
1. Press .
2. Scroll to Last Call, Answered Ca ll or Unanswered
Call, press .
3. Scroll to de sired number, press
• Or, to store the number in th e phonebook,
1. If Unanswered displays, it means you missed a call.
Press . The mi ssed caller’s number displays (if
available).
2. If multiple numbers disp la y, scroll to desired number.
3. Press .
twice to call the last dialed number.
press . See
“Create” on page 58
.
.
International Dialing1. T o look up a country/region code, press and hold
until “+” displays. Scroll to desired country/region
(abbreviated), press
OR
If you know the country/ re gi on code, enter it.
2. Enter the area code and pho ne number.
3. Press .
• Man y countries/regions includ e an i ni t ial “0” in the
area code. In most case s, th e in itial “0 ” should be
omitted when dialing inter national numbers.
• Contact your wireless service provider if you need
additional help making i nternational calls.
.
Phone Basics & Managing Calls 19
Page 24
SMS Message
Dialing
A phone number included within an SMS message can be
dialed directly. See “Inbox” starting on page 47.
ENDING CALLS
ANSWERING
CALLS
MANAGING CALLS
Voice Mail
You must subscribe to
voice mail through your
wireless service
provider before you can
retrieve voice mail
messages.
1. Press .
When there is an incomi ng call, the phone rings and
flashes green.
• If the phone is set to Quiet Mode or vibrate option, the
phone flashes green and vibrates instead of ringing.
1. Open flip and press any key except .
• Pressing any key to answer is the default setting. If
you change the setting, answer by pressing .
See “Answer Key” on page76.
OR
If the Private Handsfree Headset is attached, see
“Private Handsfre e H eadset” on page 10.
• If you pr ess
Accept or Reject, press .
• The number of unanswered/rejected calls displays.
• Press any key to clear the display.
1. When a new voice mail message is received, an alert
sounds and appears on the display.
• The display ind icate s th e nu mber of ne w voi ce mail
messages.
• remains on the display until you have listened
to all your voice messages.
2. Press and hold to automatically dial your voice
mail center number.
• If the dis pl ay in d ic at es that your voice mailbox is
empty or the number is no t va lid, contact your
wireless service prov i der .
3. Follow the recorded instructions for your voice mail.
4. Press
during an incomin g call, scroll to
when finished.
20 Phone Basics & Managing C all s
Page 25
•See “Voice-Mail” on page 63 to view the voice mail
center number.
Quiet Mode
Quickly change the ring
volume and vibration
setting of your phone to
suit your environment .
For example, the preset
Quiet Mode setting
mutes the ringer and
turns vibration on,
perfect when entering a
meeting or mo vi e.
IN-CALL
OPTIONS
While you are
connected to a call,
Voice Call and the
on-screen timer display.
If the incoming phone
number is stored in
your phonebook, then
the name matching the
phonebook entry
displays.
1. To quickly set the phone to your pr eset Quiet Mode
settings, press and ho ld
.
• To change your Quiet Mode settings, se e “Quiet
Mode” on pa ge74.
2. To disable, press and hold again
During a call, press
(
Menu) and scroll to desired
.
option:
Mute
Memo
Hold
Menu
H’free
Press to mute the current call. Press twice
to unmute.
Press to record a two-way conversation.
Warning: Recording phone calls without
the other party’s consent may violate some
state or federal laws.
Press to put a call on hold. To resume, press
, scroll to Resume, press .
Press to enter a submenu f or acce ssing Memo
to record a conversation, or the Browser,
Phonebook/V-Mail, Messages, or Calendar.
Press to switch to handsfree mode. See
“Private Handsfree Headset” on page 10. With flip
closed, also functions as speakerphone.
Adjust VolumeDuring a call, press the top or bot t om of the N avigation
key to increase or decre ase the earpiece volume.
Phone Basics & Managing Calls 21
Page 26
Note Pad
During a call, use the
keypad to enter
numbers (l i ke using a
notepad to write down a
number to call later).
1. During a call, enter a phone num ber.
2. When call ends, press
OR
When call en ds, p ress to stor e not epad numb er i n
the phonebook. See
to call notepad number.
“Create” on page 58
.
Touch Tones (DTMF)
Touch tones can be
transmitted during a call
just by pressing the
keys (0 to 9, #, *) on
your phone. Touch
tones are often used to
access voice mail,
paging, etc.... You can
save multiple touch
tone sequences with
pauses to quickly send
touch to n es to acces s
your accounts.
1. Enter phone number.
2. Press and hold until a “P” (pause) displays at the
end of the entered phone nu m ber.
3. Enter touch tone (DTMF) digi ts, for ex am pl e, the
access code for your vo ic e m ai l.
4. Press to immediately make the call.
OR
Press to save the entry.
• When the call connects, touch to nes after the
pause are automatical ly sent after 3 seconds. Or,
press again to manually send the to uc h to nes.
• To save the entry, see “Create” on page 58.
• If you need to incr ea s e t he l eng th of th e t ou ch to ne
(DTMF) digits, see “ D TM F Le ngt h” on page 76.
22 Phone Basics & Managing C all s
Page 27
Two Calls at OnceINCOMING CALL WHILE ON A CALL
(Voice calls only. Does
not apply to data and
fax calls.)
Call Waiting must be on. See “Voice Calls” on page 85.
1. While on one call, you ma y re ceive another call.
2. If so, press
Accept
Reject
SwapPress to switch between two connected calls.
End
Trans.
Merge
and scroll to desired opti on:
Press to answer the second call while putting
the origin al call on hold.
Press to reject the second call, which will be
forwarded to your selected Call Forwarding set ting.
See “Call Forwarding” on page86.
Press to end current call and keep othe r call on
hold.
When two calls are connected, press to
connect the two calls t ogether and end your
connection, leaving them to talk together.
(SIM card dependent.)
When two calls are connected (one ac tive, one on
hold), press to enable multi-party call; a ll three
of you can talk to each other.
OR
Press to en d f irst cal l, the n pr ess any key except
or to answer incoming call.
• Any Key answer is default setting. See “Answer
Key” on page 76.
3. Pressing will end both calls.
MAKING A SECOND CALL
1. During a call, enter secon d phone number or recall it
from the Phonebook.
• See “Phonebook Dialing” on page 18 .
2. Press .
• The first call is put on hold.
Phone Basics & Managing Calls 23
Page 28
Multi-Party Calls
A multi-party call has 3
to 5 people in
conversation at the
same time.
SIM card dependent.
1. Establish a multi-party call by mer gi ng tw o calls.
• See “Two Calls at Once” on page 23.
2. Continue to add people t o th e m ul t i-party call (up to 5
connections total) by calling the person or by
accepting an incoming c a ll.
• When making a call or accepting an incoming call,
the multi-party call is placed on hold. The callers
already in the multi-party ca ll can continue to talk
with each other while on hold.
• Each ad di tional connection can then be merged
into the multi-party call by pressing , scrolling to
Merge, and pressing .
MULTI-PARTY CALL OPTIONS
You can select an individual f ro m the multi-party call and
split the conversation, allowing you to talk privately
without the participation of the rest of the m ulti-party call.
1. During a multi-party call, pres s
2. Scroll to Option, press
3. Scroll to desired caller in the multi-party list, pres s
4. Scroll to de sired option, press
Split
EndPress to end that call’s connection.
5. Pressing will end the multi-party call and all
connections.
24 Phone Basics & Managing C all s
.
.
:
Press to split the selected caller from the multiparty call so you can talk privately. The remaining
multi-party callers are placed on hold and can still
talk with each other. To rejoin the call, press ,
scroll to Merge, press
.
.
Page 29
TOOLS & SET TIME MENU
To open the Tools & Set Time Menu:
1. From standby, press to open main menu display.
2. Scroll/move to highlight Tools & Set Time Menu icon
, press
.
GAME(S)
Play TETRIS
Herding Sheep.
®
or
VOICE MEMO
Record
Record a voice memo
for yourself. Or, record
your conversation
during a call. You may
record up to four voice
memos, each up to 14
seconds.
In Tools & Set Time Menu ...
1. Press [Game(s)
2. Scroll to de sired game, pr ess
• See “Games Menu” on page 39 for instructions.
Warning: Recording phone calls without the other
party’s consent may violate some state or federal laws.
1. If you are using speakerphone or handsfree during a
call (flip is closed), press .
OR
In Tools & Set Time Menu ...
1. Scroll to Voice Memo, press
2. Press (Record).
• Speak into the microphone below the keypad.
Notes:
• A tone ale rts you when recording starts and recording
automatically stops after 14 sec onds. Or, press or
to
stop recording.
• A recordi ng is automatically saved us ing t he time and
date it was recorded.
• After 4 stored conversations, the oldest recording is
overwritten.
• If you install a di fferent SI M car d, al l voi ce m emos are
lost.
].
.
.
Tools & Set Time Menu 25
Page 30
Playback
Listen to your recorded
conversations.
From standby, press , continue with step 2 bel ow.
OR
In Tools & Set Time Menu ...
1. Scroll to Voice Memo, press
2. Scroll to Playback, press .
3. Scroll to de sired recording (saved by date and time
recorded), press
Notes:
• Hold the earpiece up to your ear to hear the
recording.
• Scrollup or down to adjust volume.
• If you nee d a “notepad”, use your keypad to ente r
numbers during playb ack.
.
.
Delete
Delete recorded
conversations.
From standby, press , continue with step 2 bel ow.
OR
In Tools & Set Time Menu ...
1. Scroll to Voice Memo, press
2. Scroll to Delete, press .
3. Scroll to de sired recording (saved by date and time
DOWNLOAD DATA
Melody
Download melodies
from the internet to your
phone (via a short text
message service
through a third party).
Network dependent.
26 Tools & Set Time Menu
See details abou t th is ser vic e at:
http://www.panasonic.com/wireless
Note: Service may not be available in all countries due to
regulatory restrictions. Please check the website for
availability and further detail s.
1. After you download a melody, you will receive a
2. Scroll to select the ring tone number to store, press
.
recorded), press twice.
message containing you r se lect i on. Pr ess
twice.
• Melody is saved and can be selected as a ringtone.
See “Ring Type” starting on page 70.
.
Page 31
Logo
Download logos from
the internet to your
phone.
Network dependent.
SET TIME/ALARMS
See details about this service at:
http://www.panasonic.com/wireless
1. After you download a logo, you will receiv e a me ssage
containing your selection. Pre ss
2. Scroll to folder to store logo, press twice.
• Logo is saved and can be selected as w al lpap er.
See “Wallpaper” on page 72.
.
Clock Set
Phone has two clocks,
a home clock and an
away clock that can
show local time while
traveling. Set time for
both clocks .
In Tools & Set Time Menu ...
1. Scroll to Set Time/Alarms , press .
2. Press three times
Set). For first time set, ch oose Summer(DST) on or off.
• Press to erase current date.
3. Enter date (in day/month/year format, DD/MM/YYYY).
4. Press (Ok) to accept the date.
• Press
5. Enter time (in 24-hour military time format),
press (Ok).
SETTING DAYLIGHT SAVINGS TIME
In Tools & Set Time Menu ...
1. Scroll to Set Time/Alarms , press .
2. Press twice (Set Date/ Time > Home).
3. Scroll to Summer(DST) daylight savings time, press
.
4. Scroll to On or Off, press
AWAY CLOCK: SETTING TIME DIFFERENCE
In Tools & Set Time Menu ...
1. Scroll to Set Time/Alarms , press .
2. Press
3. Scroll to Away, press .
4. Press (Time Difference).
5. Scroll to desired difference from home clock,
press (Set
to erase curr ent time.
(
Set Date /Ti me).
).
(
Set Date /Ti me > Home > Time
.
Tools & Set Time Menu 27
Page 32
AWAY CLOCK: SETTING DAYLIGHT SAVINGS TIME
In Tools & Set Time Menu ...
1. Scroll to Set Time/Alarms , press .
2. Press
(
Set Date /Ti me).
3. Scroll to Away, press .
4. Scroll to Summer(DST), press
5. Scroll to On or Off, press
.
.
AWAY CLOCK: SETTING AUTO ADJUSTMENT
If you travel in a country/reg io n t hat has a roaming
agreement with your wireless service provider, the Away
Clock automatically adj usts to the local time.
Note: In countries/regions that have several time zones,
you must manually ad ju st th e clock.
In Tools & Set Time Menu ...
1. Scroll to Set Time/Alarms , press .
(
2. Press
Set Date /Ti me).
3. Scroll to Away, press .
4. Scroll to Auto Adjustment, press
5. Scroll to Home Area, press
.
.
6. Scroll to your home country re gi on ( abbreviated),
press
(
Set
).
• USA1 G M T-5.0 is equivalent to Eas t er n Standard
Time. USA6 GMT- 10.0 is equivalent to Hawaii
Standard Time Zone.
• Press and hold
top or bottom of navigation key
to
scroll page by page.
7. Scroll to Auto Adjustment, press
8. Scroll to Enable or Disable, press
.
.
Format Date/Time
Set which clock
displays (home or
away) and the format
for displaying time and
date.
In Tools & Set Time Menu ...
1. Scroll to Set Time/Alarms , press .
2. Scroll to Format Date/Time, press
3. Scroll to de sired option, press
Choose ClockScroll to Home Time or Away Time, press
Display Format
28 Tools & Set Time Menu
.
.
Set format for displaying time and date.
Scroll to desired fo rma t , pr e ss
.
.
Page 33
Set Alarm(s)
Set up to 4 separate
alarms with unique alert
tones.
In Tools & Set Time Menu ...
1. Scroll to Set Time/Alarms , press .
2. Scroll to Set Alarm(s), press
.
• If clock has not been set, you are prompted to set
clock first. See “Clock Set” starting on page 27.
•Warning: Ensure that any Alarm settings will not
automatically power on th e phone when in a
location that it may interfere with medical
equipment, aircraft, blasting are as , etc.... See
“Safety First” starting on page 1.
3. Scroll to alarm to set (1 to 4), p ress (Set).
4. Press to enter alarm time (hours :mi nutes) in
24-hour military time, press .
• Press to erase a previous alarm time.
5. Scroll to desired alarm interval , press
Repeat Daily, Once, or Disabled, press
Choose
6. To change the Ring Type, scroll to , press
7. Scroll to Fixed Data or Data Files, press
.
.
.
.
8. Scroll to desired folder, press , scroll to desired ring
type file, press
.
9. Press (Save).
In standby, displays to indicate alarm is set.
•
• The alar m rings based on the current clock setting
(Home or Away).
WHEN THE ALARM RINGS...
The alar m ri ng s fo r 30 s e cond s at t he s et t im e. The dis pl ay
flashes an alarm message and the flip flashes. If you are in
a call during the alarm time , the phone vibrates instead.
To stop the alarm, press an y key.
DISABLING THE ALARM
In Tools & Set Time Menu ...
1. Scroll to Set Time/Alarms , press .
2. Scroll to Set Alarm(s), press
.
3. Scroll to alarm to disable (1 to 4), pr ess .
4. Scroll to alarm interval setting
5. Scroll to Disabled, press
, press .
.
6. Press (Save).
Tools & Set Time Menu 29
Page 34
Set Pwr-Up Time or
Set Pwr-Dwn Time
Set phone to
automatically turn itself
on or off at a specified
time.
In Tools & Set Time Menu ...
1. Scroll to Set Time/Alarms , press .
2. Scroll to Set Pwr-Up Time or Set Pwr-Dwn Time,
press
.
3. Enter time in 24-hour military time format, press
4. Select interval (Repeat Daily, Once, or Disabled),
press
.
Warning: If s etting Pwr-Up Time, ensure phone
will not automatically power on in a location where it
may interfere with medical equipment, aircraft, blasting
areas, etc.... See “Safety First” on page 1.
.
CALCULATOR
Perform simple
calculations (addition,
In Tools & Set Time Menu ...
1. Scroll to Calculator, press .
2. Enter a number (maximum 10 digits).
subtraction,
multiplication a nd
division).
3. Scroll/move to select ca lcul at i on t o pe rf or m .
5. Repeat steps 2 to 4 as needed for your calculation.
6. Press (=) to display final calculation.
30 Tools & Set Time Menu
• To enter a decimal point, press or press and
hold
.
• If you sc ro ll/ m ove to select another calculat i on, t he
previous operation is pe rfor m ed with the result
displaying on the top line.
Page 35
UNIT
CONVERTER
Perform currency
calculations based on a
programmable
conversion rate.
SETTING AN INITIAL CONVERSION RATE
In Tools & Set Time Menu ...
1. Scroll to Unit Converter, press twice.
2. Enter an abbreviation for the home currency (up to 3
characters), press twice
3. Enter an abbreviation for the foreign currency (up to 3
characters), press
4. Enter the currency conv er si on rate, press
CALCULATING A CONVERSION
In Tools & Set Time Menu ...
1. Scroll to Unit Converter, press .
2. Verify that the displayed currency co nversion is
correct.
• If you nee d t o update the conversion, see “Setting
an Initial Conversion Rate” on page 31.
3. Press
4. Enter value to convert, press twice.
SWAPPING A CURRENCY CONVERSION
You can swap currenci es to co nvert from the foreign
currency into the ho m e currency.
In Tools & Set Time Menu ...
1. Scroll to Unit Converter, press .
2. Verify that the displayed currency co nversion is
correct.
• If you nee d t o update the conversion, see “Setting
3. Press three times, scroll to Swap, press .
4. Enter value to convert, press twice.
twice.
an Initial Conversion Rate” on page 31.
.
twice.
twice.
Tools & Set Time Menu 31
Page 36
INFRARED PORTPREPARING AN INFRARED CONNECTION
Transfer data between
your phone and other
devices (that have an
infrared port) using an
infrared connection. A
remote control sends
infrared signals to your
TV, VCR, etc. to control
volume or change
channels. Infrared als o
enables you to use
GSM fax and data
services, and provid es
access to the Internet
and e-mail through
existing applications.
Note: Downloaded files
with a copyright cannot
be transferred via
infrared.
32 Tools & Set Time Menu
Place your phone and the ot her device (with an infrared
port) within the effective infrared range (approx. 4”) to each
other. The infrared ports must face each other. Verify that
there are no obstructions between the two devices.
• If the othe r de vi ce is a PC, you must set up the infrared
connection on the PC. (Fo r ex am ple: Start > Settings >
Control Panel > Infrared > Options tab > Enable Infrared
Communication.) For specific infrared set up
instruc t i ons for your PC ’s operating system, ref er to the
PC’s on-line help.
SENDING IMAGES OR MUSIC DATA FROM YOUR
PHONE
Note: Images and Music data can be transferred only
between GU87 phones.
1. Verify that the infrared ports on both devices are facing
each other, and other device is set to recei ve da ta.
2. In the Files & Setup Menu, scroll to Data Files, press
Picture
or
Sound
Scroll to
, press
Send IrDA
twice, scroll to
3. Scroll to image or music data to send, press .
4. Scroll to Send IrDA, press .
• To stop the transmission, press .
SENDING YOUR PROFILE DATA FROM YOUR PHONE
1. Verify that the infrared ports on both devices are facing
each other, and other device is set to recei ve da ta.
2. In the Phonebook/V-Mail Menu, scroll to Own
Number/Info, press . Scroll to Own Number (SIM)
or Personal Info, press
press
SENDING PHONEBOOK OR SCHEDULE DATA FROM
YOUR PHONE
1. Verify that the infrared ports on both devices are facing
each other, and other device is set to recei ve da ta.
2. In the Phonebook/V-Mail Menu or the Calen dar Menu,
select individual data files to be sent, press , scroll
to
• If you se le ct data that cannot be forwarded or
.
Send IrDA
saved, your phone displ ays an error message.
, press .
.
.
,
Page 37
Receive Data
Set phone to receive
data via the infrared
port.
In Tools & Set Time Menu ...
1. Scroll to Infrared Port, press
2. Press (Receive Data
).
.
• Data is auto m at i cal ly received by phone.
3. To save the received data:
With received data displayed, press ,
scroll to SIM Phonebook or Mobile
Phonebook
SchedulerPress .
Other data
Phonebook, press .
For SIM Phonebook, press again.
For Mobile Phonebook, scroll to group
number, press twice.
Received data is automa ti cally s tored in t he
Received folder . See “Data Files” on page 65.
Connect Modem
Set phone to use a
wireless modem
connection.
Note: Make sure no
other application is
using the COM port
intended for the infrared
connection.
TEST THE INFRARED CONNECTION
Ver if y t ha t yo ur GU 87 a nd yo ur P C ar e pr oper l y c on ne ct ed.
Note: The following steps describe Windows standard
communication software (HyperTerminal).
1. Power on your GU87 handset and connect phone to
data cable or activate the Connect Modem option
under the Infrared Port featu re .
2. On your PC, select Start > Programs > Accessori es >
Communications > HyperTerminal.
3. Double click on HyperTerminal.
4. In the Connection Descr ip tion dialog box, enter GU87
in the Name field and click O K.
5. In the Connect To box, confirm that the desired com
port is selected in the “Connect using” box. Click OK.
6. In the Com Port properties bo x, sel ect 115200 bits per
second and click OK.
7. When the connect dial ogue box displays, click Cancel.
8. Select File > properties an d ver i fy th at GU 87 i s
selected. Click OK.
9. In the HyperTerminal window, type AT+ CG M I and
press Enter.
Tools & Set Time Menu 33
Page 38
Note: Windows Dial -Up
Networking version 1. 4
or later must be
installed, if running
Windows 98. U pgrades
available at:
www.microsoft.com
• If GU87 has successfully connected, you will
receive an OK reply.
CONNECTING TO THE INTERNET USING YOUR GU87
AS A MODEM
T o use the GU87 phone as a modem there are two options;
connect using the infrared port or using the Panasonic
Serial Data Cable (EB-RSD67) . See “Accessories” on
page 12 for Serial Data Cable information.
For setup instructions to make an internet connection with
your GU87 phone and a computer or PDA, visit:
Click on “Setup your De vice and Computer/PDA” and
follow the prompts to create a data c onnection specific for
the GU87 and your computer or PDA type. Instructions are
available for making the connection using either the
infrared port or using the s eria l da ta cab le .
34 Tools & Set Time Menu
Page 39
CAMERA MENU
*From standby, press
to use the camer a.
The camera is the
default shortcut setting
for the key. To
change the setting, see
“Short Cut Key” on
page 74.
Note: You cannot take
a picture while on a call.
To open the Camera Menu:
1. From standby, press to open main menu display.
2. Scroll/move to highlight Camera Menu icon ,
press
Note: Battery times are shorter when using the camera. T o
help conserve your battery, the phone automatically exits
camera mode after 3 minutes if no activity is detected.
.
TAKE A
PICTURE
1. Open flip and press , OR, open the Camera
Menu ...
2. View image on preview screen (camera viewfinder).
• For best results, hold camera about 1 foot (30cm)
away from subject.
• Inco m in g calls override the preview scr een.
• For images to display clearly, use in temperature
range of approximatel y 10 0
3. When desire d i m age displays, press shutte r button .
4. To save picture in data folder, press shutter button ,
OR, to return to camera without saving picture, press
(C),then press shutter button (Ok).
ºF (40ºC) or less.
Camera Menu 35
Page 40
• If there is an incoming call before you save the picture, it
is temporarily saved. After the call, return to camera
operation and compl ete step 4.
• If phone aut omatically exits camera mode after step 3,
return to camera operat ion and complete step 4.
• If phone is turned off, temporary images are del et ed.
Take a Self-Portra it
Zoom (2x)/Wide
Zoom in on your subject
before taking a picture.
Brightness
Adjust bri ghtness
before or after taking a
picture.
1. Open flip and press , OR, open the Camera
Menu ...
2. Close flip.
3. View yourself in the sel f -portrai t mirror.
4. Press shutter button .
5. Open flip.
6. To save picture in data folder, press shutter button ,
OR, to return to camera operation without saving
picture, press (C), then shutter button (Ok).
With image on preview screen, scroll up once to zoom.
• indicates zoom mode.
• Image clarity is diminished sligh tly w hen zoomed.
Scroll down once to return to ori gi na l (w id e vi ew) image.
• indicates wide mode.
With image on preview screen, move (scroll) right o r left.
Move right to increase brightness, left to darken picture.
• Brightness setting may not work well in dark conditions.
• indicates brightness range (-2 to +2).
• After picture is taken, go to Edit Image > Edit >
Brightness to adjust brightness.
PHOTO EDITING OPTIONS
Create special effects
before or after taking a
picture, and after the
picture is saved.
36 Camera Menu
• While viewing a picture, press up or down, or press and
hold up or down on the navigation key to scroll through
the full picture.
• If turned on, th e fe at ur es Twilight Mode, Close Up
Mode, Effect, Frame, Self Timer and Image Format
remain on until you turn them off (repeat steps 1 to 3) or
until you ex i t the camera.
Page 41
Twilight Mode
Take a picture in low
light.
In the Cam era Menu with image on preview scr een...
(
1. Press
).
2. Press (Twilight Mode).
3. Scroll to On or Off, press .
Close Up Mode
In the Cam era Menu with image on preview scr een...
Take a close up shot.1. Press
2. Scroll to Close Up Mode, press .
3. Scroll to On or Off, press .
• Close Up may not work well in dark conditions.
Effect
Take a picture in sepiatones, monochrome
(black & white) or as a
negative (reverse
colors).
Frame
Add a frame to a
picture.
In the Cam era Menu with image on preview scr een...
1. Press
2. Scroll to Effect, press .
3. Scroll to de sired effect, press .
• After picture is taken, go to Edit Image > Edit > Effect
to change color effect.
In the Cam era Menu with image on preview scr een...
1. Press
2. Scroll to Frame, press .
3. Scroll to desired frame, press . Press to briefly
view a frame. The display aut omaticall y returns to lis t
of frame s to select.
• After picture is taken, go to Edit Image > Edit > Frame
to add or change a frame.
Self Timer
Set a delay timer (10
seconds) for taking a
picture.
In the Cam era Menu with image on preview scr een...
1. Press
2. Scroll to Self Timer, press .
3. Scroll to On or Off, press .
4. Once the self timer is on, press to take a picture.
The timer ticks and the LE D blinks for 10 seconds. A
camera shutter sound plays when the picture is taken.
• If on, the s el f timer remains on until you take a pictu re ,
until you turn it off, or until you exit the cam er a.
(
).
(
).
(
).
(
).
Camera Menu 37
Page 42
Image Format
Select photo file type:
JPEG Fine (20K-30K),
JPEG Normal (5K-10K),
JPEG Economy (1K-5K)
or PNG (20K-30K). Photo
size up to 132x176 pixels.
In the Cam era Menu with image on preview scr een...
(
1. Press
2. Scroll to Image Format, press .
3. Scroll to desired format, press . The selected format
setting remains until you change it.
• After picture is taken, go to Edit Image > Edit > Image
Format to change the photo f ile type.
).
Data Files
View images in data
folder (where all saved
pictures are stored).
You can store about 20
pictures in JPEG Fine
or PNG modes; more in
lower resolution modes
(JPEG Normal or JPEG
Economy).
MMS and e-mail
Immediately send a
photo by MMS
(Multime dia Messaging
Service) or by e-mail.
Edit Image
Before and after saving
a picture, you can edit
the image. The options
Brightness, Effect,
Frame, and Image
Format are described in
this chapter.
38 Camera Menu
In the Cam era Menu
1. Press (
2. Scroll to Data Files, press .
3. Scroll to Picture folder, press (Open).
4. Scroll to desired files, pres s to view
(
or press
Copy, Move, Delete
In the Cam era Menu after picture is taken...
1. Press
2. Press for MMS, or scroll to e-mail, press . The
picture is saved in the Pict ur e data fol der, and is
attached to a new MMS or e-mail message.
3. Continue with step 3 in “Create” on page 41 to create
an MMS message. Continue with step 3 in “Create” on page 51 to create an e-mail message.
To edit the image size:
In the Cam era Menu
1. Press
2. Scroll to Edit Image, press
3. Press (Edit), scroll to Image S ize, press
4. Press (Menu>Edit), ent er des ire d widt h in %, press
(Menu>Ok).
5. Scroll to Height, press
height in %, press
Menu
().
(), or if picture is saved
).
) for other options
, or
Property
...
(Menu>Ok).
View, Rename
.
.
(Menu>Edit), enter desi re d
,
Page 43
GAMES MENU
Warning: Battery times will be shorter wh en pl aying
games (because backlighting is constant).
To open the Games Menu:
3. Scroll to desired game (Endless, 99 Line Attack, 99K
Pts Attack), press
4. Move using navigation k ey, or use 2, 4, 6, and 8 keys
to move b locks. Press to rotate blocks.
Notes:
•Select Options from game menu to see score records
or clear hi-score.
• To turn off sound, see “All Sounds” on page 69.
In Games Menu ...
1. Scroll to Herding Sheep, press .
Press for help screen.
•
2. Scroll to desired game level, press .
• Select Score to view or clear score information.
3. Press to begin game.
4. Move using navigation k ey, or 2, 4, 6, and 8 keys.
Notes:
• Press
resume play.
• Press
to pause and turn sound on/off. Press to
to exit.
®
).
.
Games Menu 39
Page 44
40 Games Menu
Page 45
MESSAGES MENU
SMS: Short Message Service allows you to send and
receive text messag es t o m obile phones on the same
network or any network that has a roaming agreement.
MMS: Multimedia Messaging Service allows you to attach
images and music to text messages. The recipient ca n
play it as a slide show (multimedia). MMS messages can
be sent to another mobile phone with MMS capability or to
an e-mail address.
e-mail: Create and send an e-mail message.
To open the Messages Menu:
1. From standby, press to open main menu display.
2. Scroll/move to highlight M essages Menu icon ,
press
MMS
Multimedia Messaging
Service allows you to
attach images and
music to text
messages. The
recipient can play it as a
slide show
(multimedia).
MMS messages can be sent to another mobile phone with
MMS capability and the sam e w irel ess service provider or
to an e-mail address.
When you receive an MMS message notice, the message
notice ind i cator () displays, along with an audible tone
or vibration. To access the message, see “Inbox” on page 43.
Note: Pictures may be modified to fi t with i n th e m ain
display of your phone.
SETTING THE PHONE FOR MULTIMEDIA MESSAGING
Before you can send a me ssage, you must program the
Message Center number (issued by your wireless service
provider). The Message Center number may be
preprogrammed on the SIM card.
.
Create
Write an MMS
message.
In Messages Menu ...
1. Press (MMS).
2. Press (Create).
Messages Menu 41
Page 46
When in the text
screen, the number
appearing below text
entry icon indicates
total av ailable
characters remaining in
message field.
Maximum character
space for MMS is 800.
Attached files will
reduce available
character space (not
reflected in number
showing on screen).
To add more pictures,
press (Menu), scroll
to Add Slide, press
(Menu), select Add Image, open Picture
folder and scroll to
desired image.
You can send only one
sound clip per
message.
If the message file is
too large, an error will
appear.
42 Messages Menu
3. Scroll to desired option, press (Select):
Add Image
Add Text
Add Sound
Slide TimeEnter time (1 to 30 seconds).
Text (color)Move to desired color, press .
BackgroundMove to desired color, press .
Scroll to folder, press , scroll to image, press
. Press to continue adding to message.
Enter message text, pre ss twice to s ave. See
“Appendix A: Text Entry” starting on page91. If
you are in an alphabe t ent ry mode, you c an ente r
a preset user message. To edit an existing
message, see “Preset Messages” on page 75.
Scroll to folder, press , scroll to sound file,
press . Press to continue adding to
message. The maximum length of a voice
recorded sound clip created by your GU87
phone is 10 seconds. If attaching an audio clip in
.amr format created by other devices, the entire
MMS message including clip cannot exceed 50
Kbytes.
4. When you finish adding files and text, press (Ok) to
go to address screen.
5. Scroll up to To: line, press (Edit), To List appears.
(
Menu
),
Press
scroll to Add, press . Enter
recipient address, pre ss (Menu>Ok), (C).
• To enter a phonebook address, press , scroll t o
desired re cipi ent, press (Menu>Recall). Scroll to
recipient address, press (Select), (C).
6. To add or change recipient e nt ries , pr es s
while at To List screen and
Accept
AddEnter another recipient address.
EditEdit recipient ent ry.
DeleteDelete recipient entry.
Save recipient entry and continue creating your
Multimedia Msg.
scroll to desired option :
(
Menu
)
7. If desired, scroll to Cc: to send a copy to another
recipient. Or scroll to Bcc: to send a blind copy.
8. Scroll to Subj:, press , enter subject, press twice.
Page 47
9. When you finish the message and return to the Create
screen, press (Menu).
10. Scroll to desire d option, press .
Send
Save
Slide Show
Other Options
Sends message to recipien t(s). A copy is saved
in the outbox.
Saves message in outbox. Message can be
edited or sent at a later time.
Plays images, sounds, and text so you c an verify
the message before sending.
Resend Attempts: Scroll to Maximum or
Custom, press .
Send ID: Scroll to Hide or Show, press .
Report: Scroll to Yes or No, press .
Delivery Time: Enter time (in hours), press .
Inbox
First choose if you want
to receive an MMS
message, then
download it to your
phone. Inbox stores
MMS message notice s
and messages you
have received.
You cannot access an
MMS message while on
a call or connected to
the browser.
In Messages Menu ...
1. Press (MMS).
2. Scroll to Inbox, press .
3. Scroll to Noticebox (number of new notices appears),
press .
4. Scroll to desired notice header.
ress (Menu
), scroll
P
to desired option, press to select:
Receive
RejectReject message.
Receive All
SortSort messages by Date, Address or Size.
Phonebook
ProtectProtect message from being overwritten .
Display
DeleteDelete message.
Status
Receive message. When complete, message
moves to Receivebox. Press (Cancel) to stop
message transmittal.
Press (Menu) to select which messages to
receive.
Save number or e-mail a ddr es s to SIM Pho nebo ok
or Mobile Phonebook.
Choose whether messages are displaye d by
Subject or Address.
View number of notice, rec eived and unused
messages.
Messages Menu 43
Page 48
Note: When playing a
message, choose
Automati c player mode
as a preview, or choose
Manual player mode to
hear the entire sound
file and scroll up/down
to view entire image
and/or text.
Press
to mute
the sound, press
to unmute.
In Automatic player
mode, scroll up/down at
start of message to
adjust volume.
Press (Menu>Play Again) to select
Automati c or Manual
player mode.
To read messages in the Re cei v ebox:
1. Press (MMS).
2. Scroll to Inbox, press .
3. Scroll to Receivebox (number of unread m essages
appears), press .
• A list of read
unread
, attached files
, and
,
locked messages displays.
4. Press twice to play the message (view images or
slideshows), or press (Menu
), scroll to desired
option, press to select:
SortSort messages by Date, Address or Size.
Phonebook
ProtectProtect message from being overwritten .
Display
DeleteDelete message.
Status
Save number or e-mail a ddr es s to SIM Pho nebo ok
or Mobile Phonebook.
Choose whether messages are displaye d by
Subject or Address.
View number of notice, rec eived and unused
messages.
Outbox
Outbox stores sent
messages and draft
messages (waiting to
be sent) that you have
created.
44 Messages Menu
In Messages Menu ...
(
1. Press
MMS).
2. Scroll to Outbox, press .
3. Scroll to de sired opti on.
Sent
Draft
Pending
Press to view a list of sent messages. Scroll to
desired message, press to view the message.
Or, pr ess (Menu) for more options.
Shows messages that have no t been s ent. Sc ro ll to
message, press (Menu) for options (Send,
Send All, Sort, Phonebook, Protect, Display,
Delete, and Status). Or, press to view
message.
Shows messages which failed during sending (i.e.,
broken connection prevented sending, etc...)
Page 49
Server List
The MMS server pro f ile
is pre-configured in
your phone. If there are
any problems, contact
your wireless service
provider.
In Messages Menu ...
1. Press (MMS).
2. Scroll to Server List, press .
3. To add another profile (for use when roaming), scroll to
an empty server profile, press .
• Create up to 3 servers.
• Do not attempt to modify the pre-configured server
profile.
• Server Au to is res er ved fo r the pr eset server sent
over the air by your wireless service provider.
4. Scroll to Edit, press .
5. Enter information in categories if necessary.
To choose a desired server profi le to us e, go to the Server
List, scroll to desired server name, press (Menu>Set).
Settings
Personal i ze MMS
message settings in
your phone.
In Messages Menu ...
1. Press (MMS).
2. Scroll to Settings, press .
3. Scroll to de sired option, press .
Font SizeScroll to desired font (text) size, press .
Display
Send Settings
Reset Snd Settgs
Receive Settings Allows messages from anonymous sender.
Report Allowe dScroll to Permit or Reject, press .
Auto ReceptionScroll to Enable or Disable, press .
Player Mode
Scroll Inbox or Outbox, press . Scroll to
Subject or Address, press .
Choose Automatic for preview or Manual to
review entire text, image, and sound files,
press . See “Inbox” starting on page 43
for details.
Messages Menu 45
Page 50
SMS
You can send and receive t ext m essages (up to 459
characters to other phones, up to 92 characters to e-mail
addresses) to mobile phones on the same network or any
network that has a roaming agreement. A message is sent
as a single message, bu t may be received as up to 3
messages (depending on the recipient’s phone settings).
When you receive an SMS mes sa ge, th e m es sage
indicator () displays, along with an audible ton e or
vibration. When Read displays, press to read the
message. Scroll up and dow n to vie w th e m essage.
SETTING THE PHONE FOR SHORT TEXT MESSAGING
Before you can send a me ssage, you must program the
Message Center number (issued by your wireless service
provider). See “Settings” on page 49. The Message Center
number may be preprog ra m m ed on the SIM card.
Send To Phone
Write an SMS mess age
to send to another
mobile phone.
When in the text
screen, the number
appearing below text
entry icon indicates
total av ailable
characters remaining in
message field.
Send To E-mail
Write an SMS mess age
to send to an e-mail
address.
46 Messages Menu
In Messages Menu ...
SMS,
1. Scroll to
2. Press (Send To Phone).
3. Enter desired messag e te xt
options Copy, Cut, User Msg. (common phrases), Char.
List, Input Mode, or Cancel.
4. When finished, press (Menu>Ok>Ok
5. Enter destination mobile phone number, press
(Menu>Ok).
6. Press
delivery confirmation, press
In Messages Menu ...
1. Scroll to
2. Scroll to Send To e-mail, press .
3. Enter desired messag e te xt
options Copy, Cut, User Msg. (common phrases), Char.
List, Input Mode, or Cancel.
4. When finished, press twice (Menu>Ok
subject, press
5. Enter destination e-mai l address, press twice.
6. Press
press
(Menu) and select No or Yes to request
SMS, press
(Ok) to send.
twice
.
, or press (
.
, or press (
.
to send.
Menu
).
Menu
) and enter
) for
) for
Page 51
Inbox
Inbox stores messages
you have received. You
can reply, create new,
forward, chat, move or
delete messages.
In Messages Menu ...
1. Scroll to SMS, press
.
2. Scroll to Inbox, press .
• A list of read
messages,
and E-SMS messages
3. Scroll to desired message
unread messages
displays.
and
press (Menu
) for
these options :
Press . Scroll up a nd down to read e ntire message,
including Sender and Message Center number. Or,
Read
ReplyEnter text, then press
Forward
ChatContinue with step 4 in “Chat SMS” on page 48.
Move
DeletePress twice to delete.
press (Menu) for submenu options (Create*,
Reply, Forward, Chat, Move, or Delete). When
Sender displays, press to add contact data to the
phonebook if desired.
twice to send.
Press . Edit mes sage, then press three ti mes.
Enter destination number, press twice.
Move message between SIM card and Mobile inbox.
indicates stored in SIM card inbox, indicates
stored in Mobile inbox.
• Create* option. If ther e i s a ph one number or e-mail
address in the message, you can create a new
message to automatic al ly send to this destination.
• While in Re ad option, if there is a phone numbe r o r
e-mail address within the text, you can press to add
it to the phonebook.
• While in Re ad option, if there is a phone numbe r in t he
message, press
to dial the number.
Messages Menu 47
Page 52
Outbox
Outbox stores sent
messages and draft
messages (waiting to
be sent) that you have
created. You can edit,
send, read, chat, create
or delete messages.
In Messages Menu ...
1. Scroll to
SMS, press
2. Scroll to Outbox, press
.
.
• A list of sent and draft messages disp l ays.
3. Scroll to desired message
and
press (Menu
) for
these options :
Press to edit text. Press (Menu) for more editing
Edit
options.
SendPress twice, enter destination, press .
Press . Scroll up and do wn to read entire message,
including Destination and Message Center number. Or,
Read
press (Menu) for submenu options (Create*, Send,
Edit, Chat, Move, or Delete). When Destination
displays, you can press to add it to the phonebook.
ChatContinue with step 4 in “Chat SMS” on page48.
Move message between SIM card and Mob ile outbox.
Move
Delete Press twice to delete.
indicates stored in SIM card ou tbox, indicates
stored in Mobile outbox.
• Create* option. If ther e i s a ph one number or e-mail
address in the message, you can create a new
message to automatic al ly send to this destination.
• While in Re ad option, if there is a phone numbe r o r
e-mail address within the text, you can press to add
it to the phonebook.
• While in Re ad option, if there is a phone numbe r in t he
message, press
to dial the number.
Chat SMS
Read chat message s
(sent and received) on
one screen when in
Chat SMS mode with
someone else.
48 Messages Menu
In Messages Menu ...
1. Scroll to
SMS, press
.
2. Scroll to Chat SMS, press .
3. Enter destination phon e num ber, press twice.
4. Enter your Nickname (u p to 18 ch aracters), press
twice.
5. Y ou can now Chat with the other party (they must have
chat SMS on their phone). Enter your message, or
Page 53
press (Menu) for more options. When finished,
press twice.
• When rec ei vi ng a chat message, text au tomatically
appears above your previous message.
6. To continue chatting, press , scroll to Ok, press .
• If the phone is not in chat mode when receiving a
chat message, it is received as an SMS message.
• If a voice call is received when in chat mo de, you
can answer the incom in g call and return to chat
mode at the end of the call.
7. To exit chat mode, press , scroll to Exit, press .
• When save is selected, the last sent me ssage is
stored in the Outbox.
• All other me ssages are automatically de le te d.
Status
Review how m any SMS
messages are stored in
the SIM card and in the
Mobile.
Settings
Create recipient group
lists to send one
message to up to 10
recipients at once. You
can also automatica lly
delete messages, set
the amount of delivery
attempts, and view the
message center
number.
The actual options that
appear may vary
depending on your
wireless service
provider.
In Messages Menu ...
1. Scroll to
SMS, press
.
2. Scroll to Status, press .
3. Select SIM Message or Mobile Message, press to
view number of messages used.
In Messages Menu ...
1. Scroll to
SMS, press
.
2. Scroll to Settings, press .
3. Scroll to de sired option, press
Create a recipient group list t o send one message
to up to 10 destin ations a t once (5 recipi ent gr oups,
with 10 destination pos i t i ons each).
.
1. To enter a new Group, select an empty slot ,
(Entry).
Recipient
Groups
press twice, press
2. Scroll to select name from phonebook (must
have phone number entry), press three
times.
3. Press to add more names to the group.
4. When finished, press (C), then press
(Menu), scroll to (Rename) and enter
Group Name. Press twice to Save.
Messages Menu 49
Page 54
Broadcasts
These are mes sages
broadcast by the
networks to all GSM
customers. They
provide general
information about topi cs
such as weather
reports, traffic news,
and customer service s.
Set to automatically erase messages.
Auto Delete
Message
Center#
ReportSelect Yes, No, or Ask to confirm delivery.
Received Read overwrites oldest read message.
Received Any overwrites oldest message,
regardless of whether it has been read or not.
Enter message center number in international dial
format. See “Setting the Phone for Short Text
Messaging” on page 46. Also see “International
Dialing” on page 19. The message center number
may be preprogrammed on the SIM card.
In Messages Menu ...
1. Scroll to
SMS, press
.
2. Scroll to Broadcasts, press .
3. Scroll to de sired option, press
ReceiveSelect On or Off to receive broadcast messages.
Message
List
Topics
Language
Scroll to desired message headers and press
to view or delete broadcast message.
At Index, press
desired topic
options Insert, Edit, Delete or Ok.
If offered by your wireless service provider,
broadcast messages can be shown in more than
one language. Select desired language.
, press (Ok). Press (Menu) for
.
(
Menu>Insert
), then scroll to
50 Messages Menu
Page 55
E-MAIL
Before you can start
sending e-mail, you
must first set up your
mMode account and
mMode Mail. See
“Server List” on page
55.
Send and receive Internet e-mail messages via an ISP that
supports POP3/SMTP protocols.
STORE AN ADDRESS
An e-mail address can be stored in the Mobile Phonebook.
See “Mobile Phonebook” on page 59.
MANAGE MESSAGE STORAGE
Once the Inbox and/or Outbox are full, any new messages
(received or created) will overwrite existing messages from
the oldest first. To prevent messages being overwritten,
delete messages which are no longer required. Lo ck
important messages so they will not be overwritten.
Create
Write an e-mail
message.
When in the text
screen, the number
appearing below text
entry icon indicates
total av ailable
characters remaining in
message field.
Maximum character
space for e-mail is
2000. Attached files will
reduce available
character space (not
reflected in number
showing on screen).
In Messages Menu ...
1. Scroll to e-mail, press .
2. Press (Create).
3. At highlighted To: line, press
(Edit), To List
appears. Press (Menu), sc roll to Add, press .
Enter recipient address, press (Menu>Ok), (C).
• To enter a phonebook address, press , scroll t o
desired recipient, press (Menu>Recall). Press
(C).
4. If desired, while at To List screen, press (Menu) for
these options:
Save recipient entry and continue creating your e-mail
message.
5. If desired, scroll to Cc: to send a copy to another
recipient. Or scroll to Bcc: to send a blind copy.
6. Scroll to Subj:, press (Edit), enter subj ect, press
twice.
Messages Menu 51
Page 56
7. File: allows you to attach a file from your Data Files to
the e-mail message.
8. Scroll to Message:, press (Edit), enter text, press
twice.
9. When you finish the message and return to the Create
screen, press (Menu).
10. Scroll to desire d option, press .
Send
Save
Sends message to recipient(s). A copy is saved in the
outbox.
Saves message in outbox. Message can be edited or
sent at a later time.
Inbox
Inbox stores e-mail
messages you have
received.
52 Messages Menu
In Messages Menu ...
1. Scroll to e-mail
, press .
2. Scroll to Inbox, press .
• A list of messages headers displays .
These icons indicate the current state of each message:
read or sent message
unread or unsent message
message has been protected
message has attached files
3. Scroll to desired message
these options :
Read
ReplyCompose a reply to the sender.
Reply to
All
Forward Send the message to a person other than the sender.
DeleteRemove the current message from the list.
Press . Scroll up and down to read ent ire message,
including Sender and Message Center number. Or,
press (Menu) for submenu options (Create*, Reply, Forward, Chat, Move, or Delete). When
Sender displays, press to add contact data to the
phonebook if desired.
Compose a reply to all recipients of the message.
and
press (Menu
) for
Page 57
Protect
Apply a lock to th e m essage so that it ca nn o t be
overwritten when receiving/cre ating further messages.
A locked message can still be deleted manually.
• While in Re ad option, if there is a phone numbe r o r
e-mail address within the text, you can press to add
it to the phonebook.
Outbox
Outbox stores sent
messages and draft
messages (waiting to
be sent) that you have
created. You can edit,
send, read, or delete
messages.
View message text. Press (Edit) for editing
options.
Press twice to make a phonebook entry. Or select
Create to create a new message.
Delete all Outbox messages.
4. To send a completed messa ge, pr ess (Menu
Send
. Or, scroll to
Save
and press to save to the
Outbox.
), then
Messages Menu 53
Page 58
Server List
Your phone can store
up to three different
POP3 email pr ofiles.
The phone will come
pre-configured with one
POP3 profile (mMode
Mail). Before you can
set up mMode Mail you
must first set up your
mMode account. Refer
to information from your
wireless service
provider.
See “E-Mail Server Profile” on page 101 to
record your e -mail
settings.
To set up your phone to use the pre-configured mMode
Mail, you will need to enter your e-mail address, as well as
the username and passwor d y ou entered when setting up
your mMode account. The entry of e-mail address,
username and password are case sensitive. Refer to
“Appendix A: Text Entry” on page 91 for entry mode help.
In Messages Menu ...
1. Scroll to e-mail
2. Scroll to Server List, press
, press.
(
Select
). Select
mMode
Mail, press (Menu), scroll to Edit, press .
3. Scroll to Mail Address, press (Edit). Enter your
e-mail address (case sensitive), press
(Menu), then
press (Save). This will return you to the mMode
Mail settings screen.
4. Scroll to SMTP Setting, press
(
Select
). Scroll to
User ID, press (Edit). Enter the username assigned
during mMode set up (case sensitive), press
(Menu), then press (Save).
5. Scroll to Password, press
(
Edit). Enter the
password assigned during mMode set up (case
sensitive), press (Menu), then press (Save).
(
Select
6. Scroll to Authentication, press
On, press (Select
)
). Scroll to
7. Press (C) to return to mMode Mail settings screen.
8. Scroll to POP3 Setting, press
User ID, press (Edit
).
Enter username assigned
during mMode set up (case sensitive), press
(Select)
. Scroll to
(Menu), then press (Save).
9. Scroll to Password, press
(
Edit). Enter password
entered during mMo de se t up (c ase sensitive), press
(Menu), then press (Save).
10. Press
(C) twice to return to the Server List screen.
11. Scroll to mMode Mail, press (Menu), scroll to Set,
press (Select) to set this server to be used.
12. Press
(C) twice to return to the main menu screen.
54 Messages Menu
Page 59
Caution: If setting up a second or third e-mail server
profile, make sure that you do not accidentally overwrite
information pre-conf ig ur ed in t he m Mode e-mail location.
To set up a second or third e-mail ser ver profile,
1. Scroll to e-mail
, press.
2. Scroll to Server List, scroll to an empty profile and
press (Create).
3. After obtaining configuration information from both
wireless service and PO P3 e-mail prov i ders, enter
information in categories as needed, press
(Menu>Save) or (Menu/Ok) each time.
• See “E- m ail Ser ver Pr of ile” on page 102 to record
your e-mail settings.
4. When finished, press (C).
To choose a desired server profi le to us e, go to the Server
List, scroll to desired server name, press (Menu>Set).
Settings
Set e-mail sending
preferences and view
status of e-mail
memory.
In Messages Menu ...
1. Scroll to e-mail, press .
2. Scroll to Settings, press .
3. Select Send Settings by pressing .
Recipient
Groups
Signature
Auto Quote
Same as Recipient Groups in SMS
messaging. See “Settings” on page 49.
Add an automatic signature to your e-mail
messages. Select Signature Setting to turn it
on or off.
Enables you to attach text from the message
that you are replying to. Set to On or Off.
To view Status, scroll to Status and press . Shows total
number of e-mail memory, vacant memory and number of
protected, unread and used messages.
Messages Menu 55
Page 60
Send/Receive
Send messages
created on the phone to
the server of the POP3
e-mail provider and
check your mailbox on
the server for inco m in g
messages and
download them to the
phone at the same
time.
In Messages Menu ...
1. Scroll to e-mail, press .
2. Scroll to Send/Receive, press .
• If there are unsent messages in the Outbox, you will
be prompted to send the m .
3. Press to send any unsent messages.
• If there ar e new messages to download to the
phone, then you will be prompted to receive them.
4. Press to re ceive new messages.
• If no action is taken, the connection will time out
after one minute.
• If any m es sages are downloaded then , when
finished, the phone will display the new messages
allowing them to be viewed, replied to, etc.... If no
messages are downloaded, the phone will display
the Inbox menu, unles s there are no messages in
this list, then it will return to the e-mail menu.
56 Messages Menu
Page 61
PHONEBOOK/V-MAIL MENU
To open the Phonebook/V-Mail Menu:
1. From standby, press to open main menu display.
2. Scroll/move to highlight Phonebook/V-Mail Menu icon
, press
The phonebook stores infor m at ion in either the SIM
Phonebook or the Mobile Phonebook. The SIM
Phonebook is best used for information you might want to
take with you if you transfer you r SIM car d t o a di ffere nt
phone. Each SIM Phonebook entry contains a name and
one phone number. The Mobile Phoneboo k i nformation
stays in your phone, unless you send it to another device
with IrDA (infrared) capability. In a Mobile Phonebook
entry, you can save information such as e-mail addresses,
up to 3 phone numbers, unique ring tones, graphics and
colors.
SEARCH
.
By Name
Review stored entries
sorted by name.
In Phonebook/V-Mail Menu ...
1. Press
twice (Search > By Name).
2. Scroll to All Phonebook (review both phonebooks) ,
SIM Phonebook, or Mobile Phonebook, press
3. Scroll to de sired entry, press .
• Press a le tter ed key to move to that letter in the list.
4. Scroll to de sired option, press
View
Detail
Recall
EditEdit entry as needed. See “Create” on pag e 58 .
DeletePress to delete the entry.
Shows list of entered informat i on for an entry by
category. Move left or right to vi ew all entries.
Each category of an entry appears on a separate
page. Scroll to view all cat egories.
Recalls the entry’s phone number to the screen to
dial. Press to dial number.
Warning: Pressing erases the number. To
cancel without changes, press or .
:
Phonebook/V-Ma il M enu 57
.
Page 62
Create
Send IrDA
(Infrared)
Create new phonebook entry for this name. See
“Create” on page 58.
Send entry information to another device with an
infrared port. See “Infrared Port” on page 32.
By Location
Review stored entries
sorted by location
number.
CREATE
SIM Phonebook
Save names with
numbers in the SIM
Phonebook (stored on
SIM card).
The number of SIM
Phonebook locations
varies based on your
SIM card.
indicates a SIM
Phonebook entry.
In Phonebook/V-Mail Menu ...
1. Press
(Search).
2. Scroll to By Location, press .
3. Press for SIM Phonebook or scroll to Mobile
Phonebook, press
.
4. Enter location number wh er e desired entry is stored,
press
5. Press
(Ok).
(Menu), continue with step 4 in “By Name”
on page 57.
In Phonebook/V-Mail Menu ...
1. Scroll to Create, press .
2. Press twice (SIM Phonebook > name icon ).
3. Enter name. Press twice to save.
• See “Ap pendix A: Text Entry” on page 91.
4. Scroll to phone number icon , press .
5. Enter phone number. Press twice to save.
6. To save in a specific locat i on, press (Save), enter
location number, press .
OR
To save in next available locat io n, press (Any).
(Location number displays on lower left.)
• If l o c ation is o c cupied or memory is full, dis p lay
prompts you to overwrite or select another location.
Press (C)
to select another location.
• If you try t o ad d a second phone number o r other
information to a SIM entry, “Item Drop?” message will
appear. Any entry other than one name and one phone
number must be droppe d to fit into the SIM Phonebook
space.
58 Phonebook/V-Mail Menu
Page 63
• Stored numbers can be transferred to another phone by
inserting your SIM card in ano th er phone.
• SIM entries cannot be grouped.
• If you edit an entry that has voice dial, you mu st del ete
the voice dial and record a n ew one. See “Add/Play/Delete” on page 60.
Mobile Phonebook
Save up to 200 names
with numbers and other
information, including
e-mail addresses,
unique ring tones,
graphics and colors,
etc....
indicates a Mobile
Phonebook entry.
In Phonebook/V-Mail Menu ...
1. Scroll to Create, press .
2. Scroll to Mobile Phonebook, press .
3. Press (name icon ).
4. Enter name. Press twice to save.
• See “Ap pendix A: Text Entry” on page 91.
5. Scroll to phone number icon , press .
6. Enter phone number. Press twice to save.
7. Scroll to desired picture icon (representing type of
phone number such as home number, business
number), press
8. Continue to scroll, select and save information:
• Phone numbers (up to 3 per ent ry)
• E-M ai l addr ess (up to 2 per entry)
Unique ring for this caller
•
• Pho to/ gr aphic to be stored for display
• Add entry to a group
•
Add note
Unique sub LCD color for this caller
•
9. To save in a specific location, press , enter location
number (1-200), press .
OR
To save in next available locat io n, press (Any).
(Location number displays on lower left.)
• If l o c ation is o c cupied or memory is full, dis p lay
prompts you to overwrite or select another location.
Press (C) to select another location.
• Saved ent ries re m ai n in th e M obi le Phonebook
even if you change the SIM card.
.
Phonebook/V-Ma il M enu 59
Page 64
WILDCARD NUMBERS
Wildcard numbers are s paces that can be stored within a
phone number. Wildcard numbers are used to hide
numbers such as a bank password, or to be able to dial
any number wi t hin a certain range while storing only one
phone number. The wildcard numbers mu st be f illed in
before the phone number is dialed.
VOICE DIALING
Add/Play/Delete
Program phone to dial
calls when you say a
pre-recorded name.
You can program up to
10 voice dial entries.
Note: Before recording
a voice dial entry, the
name and number must
be stored in the
phonebook. See
“Create” on page58.
Note: For best results,
recording shoul d take
place in a quiet
location.
Enter the wildcard numbe r b y pr essing and holding
until “_” appears.
For example, storing 555 12_ _ allows calls to all numbers
between 555 1200 and 55 5 1299. When the phone
number is recalled to the screen display, enter the wildcard
numbers and press . Wi ldcard numbers can be placed
anywhere within a stored number.
ADDING/RECORDING A VOICE DIAL ENTRY
In Phonebook/V-Mail Menu ...
1. Scroll to Voice Dialing, press .
2. Press (Add/Play/Delete).
3. If no entries have been reco rded yet, press
once
.
OR
If entries have been recorded, press
(
Menu>Add
4. Scroll to desired phonebook entry, press .
5. Scroll to Recall, press .
6. Please Record Your Voice! displays.
7. Hold phone about eight inches f rom your mo ut h, press
(Ok), and say name for select ed phonebook entry.
• A recordi ng can be up to 5 seconds in length.
8. When prompted, press , repeat voice recording.
• If reco rd in g is unsuccessful, repeat steps 7 to 8.
• To ca l l using voice dial, see “Voice Dialing” on
page 19.
).
twice
(
Add
)
60 Phonebook/V-Mail Menu
Page 65
PLAYING OR DELETING A VOICE DIAL ENTRY
In Phonebook/V-Mail Menu ...
1. Scroll to Voice Dialing, press .
2. Press (Add/Play/Delete).
3. Scroll to desired phonebook entry, press .
4. Scroll to Play or Delete, press
.
• If you select Delete, press to confirm deleti on.
• If you upd at e a phonebook entry that has a v oi ce
dial entry, you must delete and re-record the voic e
dial entry for it to work properly. Otherwise it will dial
the old number.
Auto Dial Enable
Set phone to
automatically call
entries after you recall a
voice entry.
In Phonebook/V-Mail Menu ...
1. Scroll to Voice Dialing, press .
2. Scroll to Auto Dial Enable, press .
3. Scroll to Enable (allow automatic dialing) or Disable
(must pres s before voice recorded entry is called),
press .
CALLER ID
ALERTIn Phonebook/V-Mail Menu ...
Identify callers with a
particular ring tone,
display picture/
animation, and/or sub
display color, making it
easier to distinguish
between callers or
groups of callers.
1. Scroll to Caller ID Alert, press .
2. If no Caller ID Alert has been assigned, press to
insert an initial Caller ID Alert. Or, press twice
(Menu>Insert) to insert a new Caller ID Al e rt.
3. Scroll to Personal or Group, press .
4. Scroll to de sired entry, press .
5. Press
to
Recall.
6. Scroll to de sired setting, press
Scroll to folder, press , scroll to tone,
Ring type
Photo, graphic
or animation
Sub LCD colorScroll to color, press .
press . (Operation varies based on if
this is a new entry, adding an entry or a
personal/group entry.)
Scroll to folder, press , scroll to image,
press .
7. Press (Save) to save.
Phonebook/V-Ma il M enu 61
:
Page 66
GROUP NAMES
Create group names,
for example, business
and personal. Each
group can be titled for
quick access to entries.
An alert profile can be
set for a grou p.
In Phonebook/V-Mail Menu ...
1. Scroll to Group Names, press .
2. Scroll to group <1> to <9>, press (Menu).
To view phonebook entries t hat ar e not assigned to a
group, scroll to Ungrouped.
3. Scroll to View or Edit, press :
ViewShows contents of group.
Edit
Enter group name, press
number then enter the group name. Press twice to
save group name.
. Press to clear
4. To add phonebook entries to a group, see “Mobile
Phonebook” on page 59.
STATUS
Review how many
locations are available
In Phonebook/V-Mail Menu ...
1. Scroll to Status, press .
2. Scroll to SIM Phonebook or Mobile Phonebook,
in the Phonebooks.
OWN NUMBER/
INFO
Store your own contact
information, which you
can then send to other
infrared (IrDA) devices -
- similar to an electronic
business card.
You should not make
any changes to the
Own Number (SIM)
option unless instructed
to do so by your
wireless service
provider.
62 Phonebook/V-Mail Menu
In Phonebook/V-Mail Menu ...
1. Scroll to Own Number/Info, press .
2. To save your profile in the SIM memory (if available),
3. Press
ViewView your stored mobile phone information.
Detail
Edit
DeletePress to delete your profile.
press .
press [Own Number (SIM)]. Go to step 3.
OR
To save your profile in the phone memory, scroll to
Personal Info, press twice and enter infor mation.
See “Mobile Phonebook” on page 59.
twice and scroll to desired option, press
Scroll to view each item by page of your saved
profile information.
Update profile as desired. See “Mobile Phonebook” on page 59. Press to save
changes.
:
Page 67
Create
Send IrDA
Create new profile. See “Mobile Phonebook” on
page 59.
Send your profile to another device with an
infrared port. See “Infrared Port” on page32.
SERVICE DIAL
Call your wireless
service provider.
Network and SIM card
dependent.
VOICE-MAIL
You must subscribe to
voice mail through your
wireless service
provider before you can
retrieve voice mail
messages. To check if
voice mail has been
programmed, press and
hold
displays
voice mail box nu mber is
empty , voice m ail has not
been programmed.
Contact your wi rele ss
service provide r for
programming
instructions.
. If the phone
V-Mailbox
, the
In Phonebook/V-Mail Menu ...
1. Scroll to Service Dial, press .
2. If more than one choice appears, scroll to desired entry
and press
3. Press
.
to dial your wi reless serv i ce provider.
LISTENING TO VOICE MAIL MESSAGES
When a new voice mail m ess age is received, an alert
sounds and
1. Press and hold
appears in the sub and main displays.
to dial your voice mail message
center.
OR
Press
and to dial your voice mail message
center.
2. Follow the prompts to listen to your voice mail
messages.
TO VIEW OR ENTER THE VOICE MAIL MESSAGE
CENTER NUMBER
In Phonebook/V-Mail Menu ...
1. Scroll to Voice-Mail, press .
(
2. Press
Voic e Mail
3. Scroll to de sired option, press
ViewView the voice mail center phone number.
DetailScroll to Name and Number information.
Edit
Recall
Enter the voice mail center phone number . Appe ars
only if number has not been furnished by your
wireless service provider.
Recall phone number to the s creen a nd p ress
to dial.
).
.
Phonebook/V-Ma il M enu 63
Page 68
SPEED DIAL
SETUP
Set phone to quickly
dial phone numbers
stored in Phonebook
locations 2 to 9. You
must choose either the
SIM phonebook or the
Mobile phonebook.
Note: Some speed dial
keys may be reserv ed
by your wireless service
provider. For example,
the key m ay be
assigned to voice mail
for one-touch voice mail
retrieval. If so, you will
not be allowed to
overwrite it.
In Phonebook/V-Mail Menu ...
1. Scroll to Speed Dial, press .
2. Scroll to Disable (no speed dialing), SIM Phonebook
(use SIM Phonebook en tries f or speed dialing), or
Mobile Phonebook (use Mobile Phonebook entries for
speed dialing), press .
• If you set SIM Phonebook or Mobile Phonebook,
see “Speed Dialing” on page 18 to make a call.
Note: If your wireless se rv ice pr ovider offers Service Dial,
then Service Dial will appea r as one of the Source List
options within the Speed Dial setup feat ure .
64 Phonebook/V-Mail Menu
Page 69
FILES & SETUP MENU
To open the Files & Setup Menu:
1. From standby, press to open main menu display.
2. Scroll/move to highlight Files & Set up Menu icon ,
press
DATA FILES
Storage area for
personal information
and files such as
pictures, sounds and
downloaded files.
The Data File folder types are as follows:
Folder typesContents
PicturePhotos
Sound
MailAttachments from saved e-mail messages
DownloadDownloaded files
ReceivedData received via infrared or AT commands
Phonebook
User 1 to User 5
Notes:
• Maximum file size: 50kb
• Maximum number of files: 900
• Maximum storage capacity of all data folders together: 1MB
• O nly files in supported file formats can be viewed. Files
such as word processing or spreadsheet documents
cannot be viewed, but can be stored for forwarding.
• Changing the SIM card does not affect your stored data.
.
Sounds (including melody composi tions
and voice recordings)
Small portraits assigned to Phonebook
entries
Va ries -- you can customize each of these
five folders
View Folders
Display, edit and delete
saved data (photos,
sounds, attached files,
etc.). Perform actions
for an entire folder or for
individual files within a
folder.
VIEW FOLDER IMAGES AS A SLIDE SHOW
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder to view slide show.
3. Press (Menu).
• Slide sh ow is not available for sound files.
4. Press to select Slide Show.
Files & Setu p M e nu 65
Page 70
• Each image displays for five seconds.
• To skip image, press any key except scr o ll or .
• Slide show stops after one cycle or press (Stop).
VIEW FOLDER PROPERTIES
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to de sired fold er.
3. Press (Menu).
4. Scroll to Property, pr ess .
RENAME FOLDER
Availa bl e o nl y fo r U ser 1, Us er 2, User 3, Us er 4, and Us er
5 folders.
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder (User 1 to User 5).
3. Press (Menu).
4. Press (Rename).
5. Press
(C) to clear, then enter name, press twice.
• Do not u se special characters in the fold er nam e.
VIEW FILE
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder, press (Open).
3. Scroll to desired file, press (View) for picture files,
(Play) for sound files.
EDIT FILE
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder, press (Open).
3. Scroll to desired file, press (Menu).
4. Scroll to Edit Image for pictures, EditMelody for
sound (__.imy) files, press .
• Press (Edit) for pi ctur e edit ing opt ions . See “Edit
Image” on page 38.
• You ca nnot edit pol yphon ic r ing tone s, mus ic file s, or
files that cannot be forwar ded or saved.
66 Files & Setup Menu
Page 71
ATTACH FILE TO AN MMS OR E-MAIL
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder, press (Open).
3. Scroll to desired file, press (Menu).
4. Scroll to MMS or e-mail, press .
• To create and send an MMS message, see “Create”
on page 41.
• To create and send an e-mail message, see
“Create” on page 51.
• You cannot attach polyphonic ringtones, music files,
or files that cannot be forwarded or saved.
RENAME FILE
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder, press (Open).
3. Scroll to desired file, press (Menu).
4. Scroll to Rename, press .
5. Press (C) to clear ex is ting name, edit name, press
twice.
COPY AND PASTE FILE
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder, press (Open).
3. Scroll to desired file, press (Menu).
4. Scroll to Copy, press .
5. Scroll to folder to paste file, press .
• You can copy/paste within same fold er.
• Forwa rded or saved files can not be cop ie d/ past ed.
• Copied/pasted files can be saved only into folders
for the same file types.
MOVE FILE
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder, press (Open).
3. Scroll to desired file, press (Menu).
4. Scroll to Move, press .
Files & Setu p M e nu 67
Page 72
68 Files & Setup Menu
5. Scroll to folder to move file, press .
• Files ca n be moved only into folders for th e same
file types.
DELETE FILE
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder, press (Open).
3. Scroll to desired file, press (Menu).
4. Scroll to Delete, press twice.
• If the file is used for other features, such as
Wallpaper, press again to delete the file.
TRANSFER FILE VIA IRDA (INFRARED)
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder, press (Open).
3. Scroll to desired file, press (Menu).
4. Scroll to Send IrDA, press .
• The phone transmits the file. If the file does not
transfer, you have the option to retry sending. Check
the set up for the other device.
• Note: The receiving device must be set to receive data.
•
Note: If you receive an image via Ir DA , t he file i s st ored
in the Received folder.
• Note: Downloaded data which is copyrighted cannot be
transferred.
VIEW FILE PROPERTIES
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder, press (Open).
3. Scroll to desired file, press (Menu).
4. Scroll to Property, pr ess .
PLAY MELODY RINGTONE OR MUSIC
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder, press (Open).
3. Scroll to desired file, press (Menu).
4. Press (Play).
Page 73
EDIT MELODY RINGTONE
In Files & Setup Menu ...
1. Press twice (Data Files>View Folders).
2. Scroll to desired folder, press (Open).
3. Scroll to desired file, press (Menu).
4. Scroll to Edit Melody, press .
• See “Mel ody Composer” on page 70 to edit.
• Polyphonic ringtones, music file s, and voice
recorded sounds (.amr files) cannot be edited.
Memory Status
Displays Data Folder
memory usage and
number of saved files.
SOUNDS
All Sounds
Enable or mute all ring
and key tones.
Ring Volume
Adjust ring volume,
including mute or
escalating ringing.
In Files & Setup Menu ...
1. Press to select Data Files.
2. Scroll to Memory Status, press .
In Files & Setup Menu ...
1. Scroll to Sounds, press .
(
2. Press
3. Scroll to On (all tones on) or Off (all tones muted),
press .
In Files & Setup Menu ...
1. Scroll to Sounds, press .
2. Scroll to Ring Volume, press .
3. Scroll up and down to hear vo l um e l evels.
4. Press when you hear desired volume level.
• Adjust in g volume above maximum sets escalating
All Sounds).
ringing. If you turn off ringing, displays.
Files & Setu p M e nu 69
Page 74
Ring Type
Set a unique ring to
alert you of different
types of calls (voice,
fax, dat a. .. ). Use pr es et
tones or personallycomposed melodies .
In Files & Setup Menu ...
1. Scroll to Sounds, press .
2. Scroll to Ring Type, press .
3. Scroll to type of call that will play r in g to ne, press .
4. Scroll to Fixed Data (preset to nes) or Data Files
(custom tones), press .
• If select i ng Data Files, scroll to folder, press .
5. Scroll up and down to hear r ing selections.
6. Press when you hear desired ring.
Melody Composer
Compose your own
music to use as a ring
tone.
Melodies are tagged
with an _.imy extension.
In Files & Setup Menu ...
1. Scroll to Sounds, press .
2. Scroll to Melody Composer, press .
3. Scroll to de sired option, press :
Create
Edit
MELODY COMPOSITION TABLE:
Compose music (see next table). Press twice to
save. Enter composition name. Press twice to save
in the Data folder.
Scroll to Sound, press . Scroll to composition, press
Note: Press at an y tim e t o play back melody. Scroll/
move to edit. Press to delete character(s) to left of
cursor.
Voice Recorder
Record your own
message (like a
dictaphone) or record a
two-way conversation
during a call.
Voice recordings are
tagged with an _.amr
extension. Voice
recordings cannot be
used as Ring Types.
Key-Press Volume
In Files & Setup Menu ...
1. Scroll to Sounds, press .
2. Scroll to Voice Recorder, press .
3. Scroll to de sired opti on.
Press to begin recording; speak into microphone.
Record
Edit
Press to stop recording (or, it stops automatically if
quiet for 10 seconds). Enter reco rding name. Pre ss
twice to save.
Press . Scroll to Sound, press . Scroll to
recording to edit, pr e ss . Scrol l to Ed it, pr e ss :
• Play: The recording plays.
• Rename: Edit name, press twice to save .
•Copy: Copy to paste in another folder.
•Move: Move to another folder.
• Delete: Press to delete the recording.
• Property: Press to view the file properties.
In Files & Setup Menu ...
Adjust keypad volume.1. Scroll to Sounds, press .
2. Scroll to Key-Press Volume, press .
3. Scroll to hear volume leve ls.
4. Press when you hear desired volume level.
Key-Press Sounds
Select one of four key
tone sounds.
In Files & Setup Menu ...
1. Scroll to Sounds, press .
2. Scroll to Key-Press Sounds, press .
3. Scroll to hear key tones.
4. Press when you hear desired key to ne t ype.
Files & Setu p M e nu 71
Page 76
Warning Alert s
Set a warning tone to
alert you when the
battery is low.
DISPLAY SETTINGS
In Files & Setup Menu ...
1. Scroll to Sounds, press .
2. Scroll to Warnin g Aler ts, press .
3. Scroll to On or Off, press .
Clock/Calendar
Set display preference
for clock/calendar. (Set
clock first. See “Clock Set” on page 27.)
Wallpaper
Set background
wallpaper for standby
mode. Use preset
graphics or your own
photos or graphics.
Power-up
Add text greeting and
animation during power
on.
Brightness
Adjust main screen’s
brightness level.
72 Files & Setup Menu
In Files & Setup Menu ...
1. Scroll to Display Se ttings, press .
2. Press (Clock/Calendar).
3. Scroll to display pref erence, press
.
In Files & Setup Menu ...
1. Scroll to Display Se ttings, press .
2. Scroll to Wallpaper, press .
3. Scroll to folder Fixed Data (5 preset wall paper backgrounds) or Data Folder (custom fi le s) , pr es s .
• If select i ng Data Folder, scroll to folder with
customized images, press .
• To view image, press . After viewing , press
4. Scroll to de sired file, press .
In Files & Setup Menu ...
1. Scroll to Display Se ttings, press .
2. Scroll to Power-up, press .
3. Scroll to de sired option, press :
AnimationScroll to On or Off, press .
Enter greeting (up to 120 charac ters), press
Greeting
twice.
• See “Appendix A: Text Entry” on page 91.
In Files & Setup Menu ...
1. Scroll to Display Se ttings, press .
2. Scroll to Brightness, press .
3. Scroll to desired brightness level; press .
.
Page 77
Backlight Time
Set how long the main
screen remains lighted
after using the phone.
In Files & Setup Menu ...
1. Scroll to Display Se ttings, press .
2. Scroll to Backlight Time, press .
3. Scroll to de sired time, press .
Keypad Lighting
Set keys to light or not
when pressed.
Sub LCD
Adjust contrast and set
backlighting color for
sub LCD (small display
screen on outside of
phone).
LANGUAGE
Display Language
Set the language your
phone displays.
Tegic Language
Set the language
preference for entering
text from the keypad.
In Files & Setup Menu ...
1. Scroll to Display Se ttings, press .
2. Scroll to Keypad Lighting, press .
3. Scroll to On or Off, press .
In Files & Setup Menu ...
1. Scroll to Display Se ttings, press .
2. Scroll to Sub LCD, press .
3. Scroll to de sired option, press :
ContrastScroll to adjust contrast, press .
Backlight
Color
This feature appears on ly if offere d by your wireless
service provider.
In Files & Setup Menu ...
1. Scroll to Language, press
2. Press (Display Language).
3. Scroll to de sired language; press
In Files & Setup Menu ...
1. Scroll to Language, press .
2. Scroll to Tegic Language, press
• See “Ap pendix A: Text Entry” on page 91.
3. Scroll to de sired language; press
Scroll to activity that will activate a particular
backlight color, press . Scroll to color , press .
.
.
.
.
Files & Setu p M e nu 73
Page 78
QUIET MODE
On/Off
Enable or disable Quiet
Mode.
Ring Volume
Personal i ze the ring
volume that is used
when Quiet Mode is
enabled.
Vibration
Select vibration setting
that is used wh en Qu ie t
Mode is enabled.
VIBRATION ALERT
Set phone to vibrate to
indicate an incoming
call.
SHORT CUT KEY
Set a feature to quickly
access by pressing
from standby. (Default
setting is for the
Camera.)
In Files & Setup Menu ...
1. Scroll to Quiet Mode, press .
2. Scroll to On or Off, press .
• Once set, see “Quiet Mode” on page21.
In Files & Setup Menu ...
1. Scroll to Quiet Mode, press .
2. Scroll to Ring Volume, press .
3. Scroll to hear volume leve ls.
4. Press when you hear desired volume level.
• Adjust in g volume above maximum sets escalating
ringing. If you turn off ringing, displays.
In Files & Setup Menu ...
1. Scroll to Quiet Mode, press .
2. Scroll to Vibration, press .
3. Scroll to Continuous, Intermittent, or Off; press .
In Files & Setup Menu ...
1. Scroll to Vibration Alert, press .
2. Scroll to Continuous, Intermittent, or Off; press .
In Files & Setup Menu ...
1. Scroll to Short Cut Key, press .
2. Scroll to desired short cut key, press
• From stan dby, press (below shortcut icon ) to
open the item you select ed as your shortcut.
.
74 Files & Setup Menu
Page 79
PRESET
MESSAGES
Use preset messages
as is, or edit t hem as
desired to quickly insert
into your MMS, SMS, or
e-mail messages.
KEY GUARD
Temporarily ‘locks’
keypad to prevent
accidentally pres sing
keys.
In Files & Setup Menu ...
1. Scroll to Preset Messages, press
2. Scroll to desired message, press .
3. If desired, the messag e can be edited by pressing .
• See “Ap pendix A: Text Entry” on page 91.
• To insert a user message into MMS messages, see
“Create” on page 41.
• To insert a user message into SMS messages , se e
“Send To Phone” and “Send T o E-mail” on page 46.
• To in sert a user messa ge into e -mail mess ages, se e
“Create” on page 51.
Shortcut to turn on Key Guard,
1. From standby, press and hold .
2. Press twice
OR
In Files & Setup Menu ...
1. Scroll to Key Guard, press .
2. Press .
• During i ncoming calls, you can pres s any key
except to answer the call.
• You can still dial 911 to make em ergency calls.
Calling Emergency shows on display.
TO TURN OFF/DISABLE KEY GUARD
From standby, press twice.
(Enable>Ok).
.
ANSWER MODE
H’Free Auto Ansr
Set phone to automatically answer calls when
using the Private
Handsfree Headset.
See “Private Handsfree Headset” on page 10.
In Files & Setup Menu ...
1. Scroll to Answer Mode, press .
2. Press
3. Scroll to On or Off, press .
Note: When Auto Answer is activated, the phone
automatically answer s an incoming call after 6 seconds .
(
H’Free Auto Ansr).
Files & Setu p M e nu 75
Page 80
Answer Key
Set phone so you can
answer calls by
pressing any key
(except ) or so you
can answer calls by
pressing .
DTMF LENGTH
Set length of DTM F
tones.
DEFAULT
SETTINGS
Return phone settings
to factory defaults .
In Files & Setup Menu ...
1. Scroll to Answer Mode, press .
2. Scroll to Answer Key, press .
3. Scroll to Any Key or Send Key, press .
In Files & Setup Menu ...
1. Scroll to DTMF Length, press .
2. Scroll to Long or Short, press .
Note:
T o send DTMF tones during a call, see “Touch T ones
(DTMF)” on page 22.
In Files & Setup Menu ...
1. Scroll to Default Sett i n g s , pr ess .
2. Press to return phone to factory default settings.
• Your lock code, language settings, Phonebook
entries, and voice comm ands are retained.
76 Files & Setup Menu
Page 81
BROWSER MENU
Your phone has a Wireless Appl i ca tion Protocol (WAP)
configured wireless In te rn et browser, allowing you access
to services such as new s, w eat her reports, banking,
sports, travel information and stock quotes.
WAP wireless Internet sites are de si gned to be easily
accessible on your phone, so they are usually made up of
text, hyperlinks, and may contain simple graphics to fit onto
the phone screen display . WAP sites use Wireless Markup
Language (WML), which is different than Hypertext Markup
Language (HTML) used in computer Internet websites and
cannot be accessed by w i re less phones.
When available, your phone uses GPRS (General Packet
Radio Service) technology, which is the fastest way
currently to transmit data ov er mobile phone networks .
Note: In order to access the Browser, you first must set up
your unique user name and e-mail address for your phone.
Contact your wireless service provider for details.
Note: The types of service and co ntent offere d w hi l e
connected to the Browser ar e supplied entirely by your
wireless service prov i der .
To open the Browser Menu:
From standby, press
OR
1. From standby, press to open main menu display.
2. Scroll/move to highlight Browser Menu icon ,
press
to open the Browser menu .
.
Note: Pres s and hold to launch connection to the
Browser.
Browser Menu 77
Page 82
Setup to Connect to
the Browser
START BROWSER
Launches Internet
Connection
Before starting, your wireles s ser vi ce provider may have
already completed the connection settings. To view the
connection settings on your Server List, see “Server List” on page 82.
CONNECTING TO THE INTERNET
From standby, press and hold
to launch connection to
the Browser.
OR
In Browser Menu ...
1. Press (Start Browser).
• The name of your wire l ess Intern et service provider
and an animated globe display while connecting.
2. Once the home page appea rs , you c an access the
services of your wireles s I nt er net service provider.
NAVIGATING WEB CONTENT
Wireless web pages consist mostly of text because they
are designed to be viewed on mobile phone screens .
In general...
Scroll up/down through the page content
Select a highlighted item or launch an underlined web
page
Press left to return t o previo us pa ge. Pr ess ri ght to return
to the next pag e (ava ilabl e only if bac k bu tt on wa s used) .
Return to previous page
78 Browser Menu
Disconnect the Browser at any time
Indicates non-secure on-line browsing connection.
Flashes while data is transmitting.
Indicates secure on-line browsing connection. Flashes
while data is transmitting.
Note: If you go to a site with many graphics, it may take
longer for the images to load.
Page 83
ENTERING TEXT AND NUMBERS ON-LINE
1. Press
(Edit).
2. Check the current text ent ry mode; (Abc) , ( 0-9), etc.
Press until desired text entry mode appears.
3. Enter information. Press
press
().
(Menu>Ok). If prompted,
•See “Appendix A: Text Entry” starting on page 91.
ON-LINE BROWSER MENU
Press
when Menu appears at the bot tom left of t he
display for these options, scroll to desired option, then
press :
Home Pag e Return to home page (set by network operator)
Press
Bookmark
Current URL
Enter URLType a URL to go directly to a WAP enabled site
Bookmark
Pages
Save Image Saves image displayed on current screen
ReloadReloads and updates current page
Display
Images
Clear Cache
ExitDisconnects Browser
bookmark list. Or, scroll to existing bookmark and
press
for more options.
View current URL. Press (Menu) to enter a
new URL or send URL via MMS.
Press
page content of current screen to the bookmark
pages list. Scroll to existing bookmark page and
press
for more options.
Enable or disable images from displaying to save
downloading time
Deletes content in cache and displa ys Home URL
content
(Select) to save current page to
(Select) to go to site or press (Menu)
(Select) to save website add r ess and
(Select) to go to site or press (Menu)
Note: If a call comes in while you’re on-line, you can put
the data session on hold. Press to answe r the call,
when finished, press . The phone w ill re- at tach to th e
GPRS network and brin g you to the page where you were
in the data session.
Browser Menu 79
Page 84
BOOKMARK
Open, rename or delete
bookmarks while offline.
In Browser Menu ...
1. Scroll to Bookmark, press .
2. Scroll to desired bookmark.
3. Press
bookmark site.
(
Select
) to launch the Browser and go to the
Or, press (Menu), scroll to desired
option, press :
Page INFO
Edit TitleEdit title of bookmark
DisplayDisplay bookmark list by group or by link
Delete ThisDelete selected bookmark
Delete Any
Delete AllDelete all bookmarks
View URL website address of bookmark .
Press (Menu) to enter a new URL or send
URL via MMS.
Delete multiple bookmarks. Scroll to choose
desired bookmark to delete. Sel ect by
pressing twice (Menu>Select). A
checkmark appears in the box next to the
bookmark. Continue selecting bookmarks.
When finished, press
press
to delete.
(Menu), scroll to Ok,
ENTER URL
Enter a WAP enabled
website address.
BOOKMARK
PAGES
Save the current page
URL and contents to
review off-line.
80 Browser Menu
In Browser Menu ...
1. Scroll to Enter URL, press .
2. To enter a new URL, press (<Input URL>).
Or, to edit an existing URL, scroll to URL, press .
3. Enter or edit URL.
4. Press twice to attempt to connect to entered URL.
• The URL is also saved in the URL list.
In Browser Menu ...
1. Scroll to Bookmark Pages, press .
2. Bookmark Pages list ap pears. Scroll to desired
bookmark
3. Press (Select
.
) to view page content. More than one
page from the site may have been stored in the cache. If
desired, press (
Menu
) for options Page INFO,
Protect, Delete This, Save Image or go Back.
Page 85
4. Or, from Bookmark Page list screen, press (Menu),
scroll to desired option, press :
Page INFO
Edit TitleEdit title of bookmark
Protect
Delete ThisDelete selected bookmark
Delete Any
Del. Ex. Protect Delete all except protected bookmarks
Delete AllDelete all bookmarks
View URL website address of bookmark .
Press (Menu) to enter a new URL or send
URL via MMS.
Protect bookmark from being dele ted. When
protected, lock icon appears.
Delete multiple bookmarks. Scroll to choose
desired bookmark to delete. Sel ect by
pressing twice (Menu>Select). A
checkmark appears in the box next to the
bookmark. Continue selecting bookmarks.
When finished, press
press
to delete.
(Menu), scroll to Ok,
PUSH MESSAGE
Access push me ssages
that have been sent
from the contents
provider to your phone.
BROWSER
SETTING
Personal i ze your
browser disp l ay
settings (color, text size,
etc...)
In Browser Menu ...
1. Scroll to Push Message, press .
2. Scroll to desired message, press
.
Note: To enable or disable receiving of push messages,
see “Browser Setting” on page 81.
In Browser Menu ...
1. Scroll to Browser Setting, press .
2. Scroll to de sired setting, press .
Web Page
Colors
Font Size
Scroll to Default (web p age color settings) or
Custom (your color settings), press .
Scroll to desired font size (on-screen text
size), press .
Browser Menu 81
Page 86
Scroll to Background, Text, Visited Links,
Customize
Colors
Display Images
Bookmark
Push Reception
Unvisited Links, press . Scroll/m ov e to
desired color, press twice.
Note: Press (Menu) for more color
choices. Scroll to 256 Color, press .
Scroll to Enable (display images from
website) or Disable (text only), press .
Sort bookm ark list By Link or By Group,
press .
Scroll to Enable (receive push messages) or Disable (do not receive push messages ),
press .
SERVER LISTIn Browser Menu ...
Set your phone to use a
particular wireless
Internet service
provider server when
traveling. Also set up
custom servers for
multiple SIM cards.
Change serv er settings
or add up to 4 servers.
Warning: The se settings may be preprogr am m ed by
your network operator. Modifying prev io usly entered
settings can cause failure of the Browser.
1. Scroll to Server List, press .
2. Scroll to desired server, press (Menu>Edit).
3. Scroll to de sired setting, press (Edit) or (Select).
4. Enter information in categories as needed.
To choose a desired server profi le to us e, go to the Server
List, scroll to desired server name, press (Menu>Set).
Notes:
• The Ser ve r Auto setting sets your phone to
automatically use the pr es et ser ver sent over the air by
your wireless Internet ser vice provider.
• Linger time sets the phone to automati cal ly di sconnect
from WAP server after set time of no activity. Not
required when using GPRS.
• When usi ng GPRS, it is possible to rem ain pa ss iv el y
connected to a server fo r an ind ef ini te am ount of time.
STATUS LOG
In Browser Menu ...
View last browser error.1. Scroll to Status Log, press .
82 Browser Menu
Page 87
CALENDAR MENU
Warning: Ens ur e t hat any Calendar settings will not
automatically power on the phone when in a location that it
may interfere with medical equipment, aircraft, blastin g
areas, etc.... See “Safety First” section sta rti ng on page 1.
Before opening the
Calendar Menu for the
first time, set the clock.
See “Set Time/Alarms” on page 27.
Creating a Reminder
To open the Calendar Menu:
1. From standby, press to open main menu display.
2. Scroll/move to highlight C al endar Menu icon ,
press
In Calendar Menu . ..
1. Scroll/move to select de si re d date.
2. Press twice (Menu>Create).
3. Scroll to clock icon , press
4. Enter start time (hours and minut es), press twice.
5. Enter end time (hours and minutes), press twice.
6. Scroll to reminder repea t icon , press
7. Scroll to de sired repea t t i m es, press .
• If you select Daily, Weekly, or Yearly, enter how
8. If desired, scroll to memo icon , press
9. Enter desired memo tex t, pr ess
10. Scroll to ring icon
11. Scroll to de sired ring ty pe, press
• See “Ring Type” on page 70.
12. Press (Save) to save reminder.
13. If alarm time period is more than one day, press
(
Ok) to verify the end date.
• To indicate that a reminder is set, the beginning date
.
.
.
often the reminder should occ ur, press twice.
Then, scroll to Holiday Alarm Off or On, press
.
twice.
, press .
.
is marked with a box. Additional reminder dates are
boxed.
.
Calendar Menu 83
Page 88
Viewing Reminders
In Calendar Menu . ..
1. Scroll/move to desired date, press (View).
2. Press (Detail) to view the details.
Deleting Reminders
Calendar Reminder
Options
Jump to Future Date
In Calendar Menu . ..
1. Scroll/move to select de si re d date, press (View).
2. Press
(Menu), scroll to Delete, press twice.
In Calendar Menu . ..
1. Press
(
Menu
).
2. Scroll to Options, press .
Press . Scroll to desired option, press :
• Day: Set a certain date as a r eminder or holiday.
Clear date, enter desired date of h ol i d ay, press
twice. Set date appears red on calendar.
• Day of the week: If you wish to set the same day
Holiday
Set
Status
Start of
the week
every week as a remind er, scroll to desired day of
week, press (Set). Set days appear red on
calendar.
• Holiday List: View list of set holidays. To delete
an entry, scroll to desired entry, press
(Delete>Ok).
•Status: View number of available and used
entries.
• All Clear: Press to clear all holiday entries.
View number of available and used calendar
reminders.
Set calendar weeks to start on Sunday or Monday.
In Calendar Menu . ..
1. Press
(
Menu
).
2. Scroll to Jump, press .
3. Press and hold (C) to erase current date.
4. Enter date to which you want to jump, press twice
.
84 Calendar Menu
Page 89
OPTIONS & TIMERS MENU
To open the Options & Timers Menu:
1. From standby, press to open main menu display.
2. Scroll/move to highlight Options & Timers Menu icon
, press
TIMERS & SERVICE
.
Voice Calls
Review voice call timers
and phone number
display status.
SIM card dependent.
Data Calls
Review data call timers
and amount of data
transferred. Also, set
whether voice or data
calls have priority.
SIM card dependent.
In Options & Timers Menu ...
1. Press
2. Scroll to desired option to review, press
Last Call
Timer
All Calls
Timer
Call Waiting
Caller’s ID
Notes: Times display as HH:MM:SS (hours:minutes:seconds).
The actual time invoiced for calls by your wireless service
provider will vary from the time represented on your call timer.
The invoiced time is affected by the number of network features
selected, when billing begins and ends , and rounding for billing.
twice (Timers & Service > VoiceCalls).
.
Length of last voice call.
(Incoming or Outgoing)
Total time of all incoming or outgoing voice calls.
Press to see if Call Waiting is enabled or
disabled. Press to exit. Or, to change setting,
press , scroll to ot her option and press .
See “Incoming Call while on a Call” on page 23.
Choose whether caller’s ID is displayed or
hidden.
In Options & Timers Menu ...
1. Press
2. Scroll to Data Calls, press
3. Scroll to de sired option, press
Last Connection
All Connections
(Timers & Service).
.
.
Length of last connection and amount of
data transferred durin g ca ll.
Total time of all connectio ns and total
amount of data transferred.
Options & Timers Menu 85
Page 90
Set whether an incoming voice call can
Call Priority
Note: Times display as HH:MM:SS (hours:minutes:seconds).
The actual time invoiced for calls by your wireless service
provider will vary from the time represented on your call timer.
The invoiced time is affected by the number of network features
selected, when billing begins and ends , and rounding for billing.
interrupt a d a ta call. To set, scroll to
Enable (voice has priority over data) or
Disable (data calls are not interrupted)
press
.
,
Send Caller ID
Set to transmit your
number to another
phone (caller ID).
In Options & Timers Menu ...
1. Press
(Timers & Service).
2. Scroll to Send Caller ID, press
3. Scroll to Networ k set, On, or Off, press
Network dependent.
CALL
FORWARDINGIn Options & Timers Menu ...
Forward incoming calls
(voice, data, fax) to
another number.
Network dependent.
1. Scroll to Call Forwarding, press
2. Scroll to de sired option, press
Fwd Voice Calls
or
Fwd Fax Calls
or
Fwd Data Calls
Cancel AllPress to cancel call forwarding.
StatusView current settings.
Note: When updating or viewing settings, your phone must be
registered on a network.
Press , then scroll to desired option, press
. Enter phone number where call should be
forwarded; or, press
stored phone number or
group). After number is entered, press
twice. Call forwarding icon () displays.
.
.
.
.
(once to select a
twice to select a
86 Options & Timers Menu
Page 91
SECURITY
Lock Phone
Prohibit phone use
except to answer calls
or to dial 911.
Preset code is 1234.
Warning: If you
change the lock code,
be sure to record your
new code in the inside
back cover page.
If you forget the lock
code, you will have to
send the phone to an
authorized service
center to restore the
phone to the default
lock code. The lock
code cannot be
restored by a call to
customer service.
Security functions can help protect your phone from
unauthorized use. You should memorize your se curity
codes. If you do need to writ e down any of your codes, do
not writ e them where they can b e viewed or recognized by
someone else. If you ever forget your PIN or PIN2 code(s),
contact your wireless service provider.
Note: Emergency calls can still be m ade even if security
options have been set.
Shortcut to turn on Lock Phone,
1. From standby, press and hold .
2. Scroll to Lock Phone, press
3. Enter the 4-digit lock code , press
(Enable).
(Ok).
OR
In Options & Timers Menu ...
1. Scroll to Security, press
.
2. Press (Lock Phone).
3. Scroll to de sired option, press
(
On/Off). Scroll to On (phone lock
Off
(phone lock off), press . Enter
On/Off
Change Code
Press
on) or
4-digit lock code, pr ess . (Enter 1234 if you
have never changed the lock code.)
If you set the phone lock to On, the phone
locks and the lock icon () displays. Enter
the 4-digit lock code and press to use
phone.
Enter 4-digit lock code , press . (Enter
1234 if you have never change d the lock
code.) Enter new 4-digit lock code, press .
Enter new code again, press .
.
Options & Timers Menu 87
Page 92
PIN or PIN2
The PIN (Personal
Identification Number)
protects your SIM
against unauthorized
use. When enabled,
you must enter the PIN
every time you turn on
the phone.
PIN2 controls secur ity
for Dial Only PhBook
and No SIM PhBk Dial.
In Options & Timers Menu ...
1. Scroll to Security, press
2. Scroll to PIN or PIN2, press
3. Scroll to de sired option, press
Scroll to Enable (PIN/PIN2 protecti on on) or Disable
Enable/
Disable
Change
Code
Note: If PIN or PI N2 is entered incorrectly 3 times, the phone
locks. Contact your wireless service provider for a PUK or PUK2
(personal unblock key) code. The PUK unblocks a disabled PIN
code, and the PUK2 unblocks a disabled PIN2 code. If the PUK
or PUK2 code is entered incorrectly 10 times, the phone will not
operate. All information stor ed in the S IM card is lost and the SIM
card must be replaced.
(no PIN/PIN2 protection ), press . Enter 4- to 8digit PIN/PIN2, press .
If you set Enable, enter PIN/PIN2 and press
every time you turn on phone.
Enter PIN/PIN2, press . Enter new 4- to 8-digit
PIN/PIN2, press . Enter new PIN/PIN2 again,
press .
.
.
.
Dial Only PhBook
Dial Only PhBook is part of the Phonebook, but with added
security.
This feat ure allows you
to restrict calls to a list
of permitted phone
numbers.
For example, if lending
your phone to one of
your children, you may
In Options & Timers Menu ...
1. Scroll to Security, press
2. Scroll to Dial Only PhBook, press
3. Scroll to Enable or Disable, press
4. Enter PIN2, press
• First, set this feature to Enable, then store numbers that
want to restrict their
dialing to your home
• When Dial Only PhBook is enabled, any manually
and office numbers.
SIM card dependent.
• When enabled, phone numbers can be added, edited or
Requires PIN2 code.
88 Options & Timers Menu
.
.
.
.
will be permitted to be dialed. The y w i ll be sto re d i n the
phonebook.
dialed phone number m ust match a stored phone
number in the permitted list.
deleted as normal, but you will be prompted for PIN2.
Page 93
No SIM PhBk Dial
Prohibit manual dialing
of pre-programmed
phone numbers in the
SIM Phonebook.
SIM card dependent.
Requires PIN2 code.
NETWORK
In Options & Timers Menu ...
1. Scroll to Security, press
2. Scroll to No SIM PhBk Dial, press
3. Scroll to Enable or Disable, press
4. Enter PIN2, press
Note: This feature is not av ailable on th e AT &T
Wireless Services network.
.
.
.
.
Network Search
Manually select an
available network when
using your phone
outside of your home
area (roaming).
Search Mode
Set phone to
automatically search for
networks when roaming
or set phone so you can
manually select a
network when roaming.
In Options & Timers Menu ...
1. Scroll to Network, press
2. Press (Network Search).
3. Scroll to desired network to use, press
Note: An “X” displays if you cannot register with the
selected network.
Note: Roaming charges ma y apply.
In Options & Timers Menu ...
1. Scroll to Network, press
2. Scroll to Search Mode, press
3. Scroll to Automatic or Manual, press
Note: If you select Manual, you will have to manually
select a network. See “Network Search” on page 89.
.
.
.
.
.
Options & Timers Menu 89
Page 94
Network List
View available
networks.
Search Mode must be
set to Automatic. See
“Search Mode” on
page 89.
In Options & Timers Menu ...
1. Scroll to Network, press
2. Scroll to Network List, press
3. Scroll to view available ne two rk s
.
.
.
SIM card dependent
.
TEXT TELEPHONY
Allows a hearingimpaired person to use
the phone by
connecting a TTY
device.
To set TTY mode, in Options & Timers Menu ...
1. Scroll to Text Telephony, press
2. Scroll to On or Off, press t w ice t o tu rn on, once to
turn off.
• When on, any accessory that is conne cted t hr ough
the 2.5 mm Headset/TTY connector is expected and
assumed to be a TTY device.
• TTY mode must be enabled to send and receive
TTY calls.
• When ma ki ng a TTY call, plug in the TTY device
before making a call.
• To answer a TTY call, you may answer the call with
or without the device plugged in and then plug in if
not already connected.
• If TTY is enab le d, the TTY icon is indicated at
the top of the display.
.
90 Options & Timers Menu
Page 95
APPENDIX A: TEXT ENTRY
Use the phone’s keypad to enter text , characters and numbers. There are multiple
ways to enter text/characters/numbers:
• Standard Text Entry (ABC entry with Englis h, Gree k and international letters)
• Tegic Language Entry (also known as T9
commonly-used words)
• Character Entry (includes upper and lo w er case letters, numbers, and standar d
characters such as a period, @, slash, colon, semicolon, brackets, etc....)
• Number Entry
Standard Text Entry
To enter a letter, press a nu m b e r key one to
seven times until correspon ding letter on the
key displays.
Enter English alphabet (ABC), Greek
characters (ΑΒΓ), or international characters
(AÄÅ).
Recommended for entering proper names or
words not commonly found in a diction ary.
Entering/Editing Text, Characters, and Numbers
When ready to enter information (flashing cursor):
1. The current input mode app ears at lower left of the display. Press repeatedly
to scroll through the input modes; T9, Abc, 0-9, ΑΒΓ, AÄÅ; (not character list).
OR
Press (Menu), scroll to desired text entry method, press (Select):
Char. ListScroll/move to select desired letter, number or character. Press .
Input Mode
Scroll/move to select desired text entry method: T9, Abc, 0-9, ΑΒΓ, AÄÅ.
Press .
2. Enter text, characters or numbers.
•See the following table for details about what each key press will enter.
•Flashing cursor in dicates where next letter/char acter/number will be entered.
®
Text/Quick Entry for entering
Tegic Language Entry
(or, T9® Text/Quick Entry)
To enter a letter, press the corresponding
number key once. As you enter a word, the
phone displays the most likely word match for
your entry . If the cor rect word does not di splay,
press repeatedly to scroll through an
alternate word list.
Enter words included in the p hon e’ s di ction ary.
(Note: You can add words to the dictionary).
Recommended for commonly-used words.
Appendix A: Text Entry 91
Page 96
Scroll up or down to move through lines of text. Move left or right to
move along a line of text.
T o enter consecutive letters from the same key, pause for a second and
the cursor automatically moves to the next space. Or, use the
navigation key to move right or left the desired number of spaces.
Press repeatedly to sw itc h am ong first letter capital, CAPS LOC K and
all lowerc ase text entry modes.
to
Shortcut: Press and hold any numeric key to ente r the character menu
(Char. List), except while in T9 or 0-9 mode.
Press repeatedly to sw itc h among text entry modes a s nee ded.
Press briefly to delete previous letter/character/number. Press and hold
to erase the entire entry. (Note: Usually, pressing this key cancels the
current screen. However, in text mode, to cancel the current screen ,
press (Menu), scroll to Cancel, and press (Select).
3. When your entry is com pl et e, pr ess (Menu > Ok).
Normal (ABC)Greek (ΑΒΓ) Extended (AÄÅ)Numeric (0 - 9)
.@:;*#+”,!¡?¿
_()[]{}’&%\^~|
<>=€£$¥¤§
.@:;*#+”,!¡?¿
_()[]{}’&%\^~|
<>=€£$¥¤§
.@:;*#+”,!¡?¿_()[]{}’&
%\^~|<>=€£$¥¤§
92 Appendix A: Text Entry
1
Page 97
APPENDIX B:
SPECIFICATIONS & TROUBLESHOOTIN G
SPECIFICATIONS
PHYSICAL CHARACTERISTICS
Dimensions
Weight (including battery)3.63 oz. (103g)
Network bandsGSM 900, GSM 1800, GSM 1900
Maximum RF Output1 W
AntennaFixed
TROUBLESHOOTING
Should any problem continue, please contact your wirel ess service provider.
ProblemCausePossible Solution
Phone will not turn on
Extremely short battery lif e for
a new battery
Short battery life for an old
battery
The charging indicator does
not light, the battery level
indicator does not appear and
the phone cannot be switched
on when charging
Battery fails to charge
The network you are using
and the condition of the
battery can affect battery life
The battery has worn out
The battery is not attached to
the phone or when the battery
has been deeply discharged
the phone will take a short
time until the indicator l i ghts
The battery is not attached to
the phone
Battery has been c onnected to
the phone after the Rapid
Charger has been turned on
3.84” x 1.93” x 0.91”
(97.5 x 49 x 23 mm)
Check that the battery is fully
charged and correctly
connected to the phone
Replace with a new fully
charged battery
Leave the phone charging the
battery for a few minutes
before the indicator is lit and
attempting to switch it on
Ensure the batter y is fitted to
the phone prior to
commencing charging.
Appendix B: Specifications & Tr ou bl eshooting 93
Page 98
ProblemCausePossible Solution
The phone is lockedUnlock the phone
Disable the outgoing call
barring, or barred dial
Move to a coverage area and
operate your phone after it has
registered with a network.
Check your SIM card supports
Fixed Dial
Check if the Fixed Dial is
switched on
Check the phone number is
stored in the Fixed Dial
Disable the incoming call
barring
Move to a coverage area and
operate your phone after it has
registered with a network
Check that the antenna
symbol is displayed - move
to a coverage area and
operate your phone when the
antenna symbol is displayed
Switch off restriction
Calls cannot be made
Calls cannot be made from
Fixed Dial Store
Calls cannot be received
Emergency calls cannot be
made
Phone numbers cannot be
recalled from Phonebook
Outgoing calls are barred
The phone is not registered to
a network
The phone is not switched on Switch the phone on
Incoming calls are barred
The phone is not registered to
a network
You are not in a GSM
coverage area
The phone is lockedUnlock the phone
Phone number has been
restricted
IMPORTANT ERROR MESSAGES
These are some of the mos t important error messages whic h m ay be displayed:
Error MessageMeaning
Area Not AllowedRoaming in the selected area is not allowed
Auto Redial List Full
Attempt Failed...Please Try
Again
94 Appendix B: Specifications & Tro ubl e shooting
Redial list of unsuccessfully dialed numbers is full - switch the
phone off and the n on again
The phone experienced a failure connecting to the network
when attempting to place an emergency (911) call.
Page 99
Error MessageMeaning
The phone experienced one of the following conditions:
1. Call was not able to connect to the network (no circuits
Call Rejected
Emergency Calls Only
Function Unavailable
Incorrect Lock Code
Incorrect PIN / PIN2 / PUK /
PUK2
Message Rejected S tore Full
Network Not AllowedRoaming with the selected network is not allowed
Phone Number Too Long
(Max:20)
PIN2 Invalidated
Security Failure
SIM Blocked / Contac t Service
provider
SIM Error
SIM Invalid
available, no signal available or out of service area.)
2. Battery charge level i stoo low (recharge battery).
3. Your calling plan is expired, depleted or has reached its
preset limit.
May occur when phone is outside coverage area or in a
coverage hole. Another carrier may be restricting access to
placing emergency calls only. Press or to go back to
the standby screen. When you re-enter the AT&T coverage
area, your phone can receive calls even though Emergency
Calls Only message may still appear on the display.
The selected feature is eit her not suppor ted by the SIM card or
is not available with the current subscription - contact yo ur
wireless service provider
Disabling or enabling the lock co de has failed due to incorrect
entry of the lock code - re-enter lock code
The entered code is incorrect - re-enter code correctly
A message has been recei ve d but t he mes sage sto re i s fu ll - t o
receive messages, delete some of the currently stored
messages or set messages to Auto Delete
The edited or newly created Phonebook number is too long for
the SIM card
The PIN2 is blocked permanent ly because the wrong PUK2
has been entered ten times, s ervices controlled by PIN2
cannot be used - contact your wireless service provider
The network has detected an authentication failure because
your SIM card is not registe red with th at network - cont act your
wireless service provider
The SIM is blocked because one of the PIN/PIN2 unblocking
keys (PUK/PUK2) has been entered incorrectly ten times contact your wireless service provider
The phone has detected a problem with the SIM card- switch
the phone off a nd then ba ck on; if the mes sage is s till di splayed
contact your wireless service provider
The SIM card has failed one or more of the SIM card
personalization checks - contact your wireless service provider
Appendix B: Specifications & Tr ou bl eshooting 95
Page 100
Error MessageMeaning
Ver ification Failure
Warning Store Full Continue?
On changing the phone lock code, verification of the new code
is incorrect - retry changing the lock code with correct
verification
The message area is full. Your messages cannot be stored
until some of the currently stored messages are deleted
96 Appendix B: Specifications & Tro ubl e shooting
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.